Drawer and cabinet specifications

Rear mounting bracket

Front view Drawer back preparation

10 (3/8")

37 (1-7/16")

Profile length

A

B

9 (11/32")

4 (5/32") Setback

Inside cabinet depth

295.3750.01

Rearmountingbracket

612TH

Min. topclearance

6 (1/4") Inside cabinet width

Drawer width

Ope

ning

13 (1/2”) Bottom recess

Drawer side thicknessmaximum 16 (5/8”)

14 (9/16”)Bottom clearance

37

(1-7

/16"

)

21 (13/16")

Drawer height maximum =

opening minus 20 (13/16”)

System or #7 profilemountingscrews

page 52

Inside cabinet width

7 (9/32")

1 1 (7/ 1 6")

Ø6 x 1 0 bo r e f or hook

33 (1-5/16") minimum rear notch

13 (1/2")

12

Face frame rail

Face

fram

e st

ile

1632

14 (9/16")

(1-1

/4")

(5/8

")(3

/32"

)2

21(13/16")

(15/32")

*NOTE: For panel applications the first screw location is always 37 (1-7/16")

21Dimensions in millimeters (inch equivalents as noted)

Drawer and cabinet specifications

25 (31/32")

37 (1-7/16")

32 (1-1/4”)

33 (1-5/16”)

6 (1/4”)

9 (11/32”)

Profile close-up

NOTE: For frame applications. Minimum 3 screws per bracket.Example: For 21" inside cabinet width and a 5/8" thick drawer, 21" minus 3/8" = 20-5/8" drawer width

Profile mounting specifications

Calculating outside drawer width

For drawer side thickness 16 (5/8") 15 (19/32") 14 (9/16") 13 (1/2") 12 (15/32")Deduct from inside cabinet width 10 (3/8") 12 (15/32") 14 (9/16") 16 (5/8") 18 (23/32")

TANDEM plus TANDEM plus BLUMOTION

Drawer length

Inside cabinet depth with 295.3750.01 bracket

Profile length

Screw locations for panel cabinets

Maximum Minimum A B

562H2290B10 229 (9") 299 (11-3/4") 266 (10-1/2") 262 (105/16") 133 (5-1/2") 229 (9")562H3050C 562H3050B 305 (12") 369 (14-9/16") 326 (12-7/8") 317 (12-1/2") 165 (6-1/2") 261 (10-1/4")562H3810C 562H3810B 381 (15") 446 (17-9/16") 403 (15-7/8") 394 (15-1/2") 165 (6-1/2") 357 (14-1/16")562H4570C 562H4570B 457 (18") 522 (20-9/16") 479 (18-7/8") 470 (18-1/2") 261 (10-1/4") 453 (17-13/16")562H5330C 562H5330B 533 (21") 598 (23-9/16") 555 (21-7/8") 546 (21-1/2") 261 (10-1/4") 517 (20-3/8")

NOTE: Orange dots indicate screw locations required to meet specified load capacities

Extension FullMax. drawer material 16 (5/8")

Dynamic load capacity 75 lbStatic load capacity 100 lb

TANDEM plus 562F full extension drawer runners

pg. 28 pg. 32 pg. 33 pg. 38 pg. 46

Installation screw 707NInstallation screw 661.1300HG

Runner profileLocking device

22Subject to technical modifications without notice. © 2008

Description Basic components

Full extension concealed drawer runners █

Available with integrated BLUMOTION █

For █ 19 (3/4) max. drawer side thicknessRear tilt adjustment █

Concealed roller carriages with █

permanently lubricated synthetic rollers create a smooth running actionLocking devices enable easy drawer █

insertion and removalForce guided right side and ± █ 1.5 (1/16") tolerance - compensating left sideDynamic load capacity of 75 lb █

Static load capacity of 100 lb █

Components

For overall cabinet depth

Drawer length Over extension TANDEM plus

TANDEM plus BLUMOTION

305 (12") 229 (9") 0 562F2290B10381 (15") 305 (12") 0 562F3050C 562F3050B457 (18") 381 (15") 0 562F3810C 562F3810B533 (21") 457 (18") 6 (1/4") 562F4570C 562F4570B610 (24") 533 (21") 16 (5/8") 562F5330C 562F5330B

Other applications

NOTE: These runners are for 19 (3/4") max. drawer side thickness

One set required per drawer

Overlay application

pg. 30Narrow drawer Deep drawerORGA-LINEBottom mountRoll-out shelfInset drawer

Using TANDEM page 14 Drawer preparation page 15 Accessories page 52 Assembly aids page 54

Profile set

Rear mounting bracket for frame cabinets

Two required per drawer █

Depth and side-to-side self-alignment █

Zinc-plated steel █

Non-handed bracket 295.3750.01Installation screw 612TH

For use when installing TANDEM runners in face frame cabinets. Not necessary for panel cabinet installation.

Standard locking device

page 14

Right locking device T51.1700.04 R

Left locking device T51.1700.04 LInstallation screw 612TH

One right and one left required per drawer █Minimum interior drawer width █ 121 (4-3/4")Height adjustable █ +3 (1/8")

Installation

NOTE: See page 48 for other optionsPart no.

Part no.

Part no.

NOTE: See page 50 for 9" TANDEM rear attachment options

Rear mounting bracket


10 (3/8")

37 (1-7/16")

Profile length

A

B

9 (11/32")

4 (5/32") Setback


295.3750.01

Rearmountingbracket

612TH

Min. topclearance


Drawer width

Ope

ning




37

(1-7

/16"

)

25 (15/16”)



System or #7 woodscrews

page 52

Inside cabinet width7 (9/32")

1 1 (7/ 1 6")



13 (1/2")

12

Face frame rail

Face

fram

e st

ile

1632

14 (9/16")

(1-1

/4")

(5/8

")(3

/32"

)2

21(13/16")

(15/32")




25 (31/32")

37 (1-7/16")

32 (1-1/4”)

33 (1-5/16”)

6 (1/4”)

9 (11/32”)

Profile close-up

Example: For 21" inside cabinet width and a 3/4" thick drawer, 21" minus 7/16" = 20-9/16" drawer width

NOTE: For frame applications. Minimum 3 screws per bracket.


Calculating outside drawer width

For drawer side thickness 19 (3/4") 18 (23/32") 17 (21/32") 16 (5/8") 15 (19/32")Deduct from inside cabinet width 11 (7/16") 13 (15/32") 14 (9/16") 10 (3/8") 12 (15/32")

TANDEM plus TANDEM plus BLUMOTION Drawer length

Inside cabinet depth with 295.3750.01 bracket Profile length

Screw locations for panel cabinets

Maximum Minimum A B

562F2290B10 229 (9") 299 (11-3/4") 266 (10-1/2") 262 (10-5/16") 133 (5-1/2") 229 (9")

562F3050C 562F3050B 305 (12") 369 (14-9/16") 326 (12-7/8") 317 (12-1/2") 165 (6-1/2") 261 (10-1/4")

562F3810C 562F3810B 381 (15") 446 (17-9/16") 403 (15-7/8") 394 (15-1/2") 165 (6-1/2") 357 (14-1/16")

562F4570C 562F4570B 457 (18") 522 (20-9/16") 479 (18-7/8") 470 (18-1/2") 261 (10-1/4") 453 (17-13/16")

562F5330C 562F5330B 533 (21") 598 (23-9/16") 555 (21-7/8") 546 (21-1/2") 261 (10-1/4") 517 (20-3/8")




TANDEM plus 568H/568. heavy duty drawer runners


pg. 28 pg. 33 pg. 34

Installation screw 707N Installation screw 661.1300HG



Full extension concealed drawer runners █with integrated BLUMOTIONFor █ 16 (5/8") max. drawer side thicknessFrame applications must be blocked out █Rear tilt adjustment █Concealed roller carriages with █permanently lubricated synthetic rollers create a smooth running actionLocking devices enable easy drawer █insertion and removalForce guided right side and ± █ 1.5 (1/16") tolerance - compensating left sideDynamic load capacity of 110 lb █Static load capacity of 125 lb █

Components


Drawer length

Over extension


533 (21") 457 (18") — 568H4570B610 (24") 533 (21") — 568H5330B686 (27") 610 (24") 19 (3/4”) 568.6100B762 (30") 686 (27") 20 (13/16”) 568.6860B838 (33") 762 (30") 28 (1-1/8”) 568.7620B

Other applications

NOTE: These runners are for 16 (5/8") max. drawer side thicknessOne set required per drawer

Overlay application

pg. 46pg. 38ORGA-LINE Deep drawerBottom mountInset drawer SPACE CORNER


NOTE: For heavy duty applications, rear brackets and sockets cannot be used. Cabinet sides must be blocked out flush with the inside of the frame. See page 25.

Profile set



page 14



One right and one left required per drawer █

Minimum interior drawer width █ 121 (4-3/4")Height adjustable █ +3 (1/8")

Installation


Part no.


10 (3/8")

37 (1-7/16")

4 (5/32") Setback

Profile length

A

B

9 (11/32")


Blocking forframe applications

Min. topclearance


Drawer width

Ope

ning




37

(1-7

/16"

)

21 (13/16")



System or #7 profilemountingscrews

page 52


7 (9/32")

1 1 (7/ 1 6")



13 (1/2")





25 (31/32")

37 (1-7/16")

32 (1-1/4”)

33 (1-5/16”)

6 (1/4”)

9 (11/32”)

Profile close-up



TANDEM plus BLUMOTION Drawer length Minimum inside

cabinet depth Profile lengthScrew locations for panel cabinets

A B568H4570B 457 (18") 477 (18-3/4") 470 (18-1/2") 261 (10-1/4") 453 (17-13/16")568H5330B 533 (21") 553 (21-3/4") 546 (21-1/2") 261 (10-1/4") 517 (20-3/8")568.6100B 610 (24") 633 (24-15/16") 626 (24-11/16") 261 (10-1/4") 389 (15-5/16")568.6860B 686 (27") 703 (27-11/16") 696 (27-7/16") 261 (10-1/4") 389 (15-5/16")568.7620B 762 (30") 778 (30-5/8") 771 (30-3/8") 261 (10-1/4") 389 (15-5/16")

Calculating outside drawer widthFor drawer side thickness 16 (5/8") 15 (19/32") 14 (9/16") 13 (1/2") 12 (15/32")

Deduct from inside cabinet width 10 (3/8") 12 (15/32") 14 (9/16") 16 (5/8") 18 (23/32")



TANDEM plus 568F/568A heavy duty drawer runners

pg. 34pg. 28 pg. 33

Installation screw 707NInstallation screw 661.1300HG


Drawer length Over extension


533 (21") 457 (18") — 568F4570B610 (24") 533 (21") — 568F5330B686 (27") 610 (24") 19 (3/4”) 568A6100B762 (30") 686 (27") 20 (13/16”) 568A6860B838 (33") 762 (30") 28 (1-1/8”) 568A7620B

NOTE: These runners are for 19 (3/4") max. drawer side thicknessPart no.



Full extension concealed drawer runners █

with integrated BLUMOTIONFor █ 19 (3/4) max. drawer side thicknessFrame applications must be blocked out █

Rear tilt adjustment █

Concealed roller carriages with █

permanently lubricated synthetic rollers create a smooth running actionLocking devices enable easy drawer █

insertion and removalForce guided right side and ± █ 1.5 (1/16") tolerance - compensating left sideDynamic load capacity of 110 lb █

Static load capacity of 125 lb █


Other applications


Overlay application

Bottom mountInset drawer SPACE CORNER pg. 46pg. 38ORGA-LINE Deep drawer


NOTE: For heavy duty applications, rear brackets and sockets cannot be used. Cabinet sides must be flush with the inside of the frame. See page 27.

Profile set

Rear mounting bracket for frame cabinets Standard locking device

page 14





Installation

NOTE: See page 48 for other options

Part no.


10 (3/8")

37 (1-7/16")

4 (5/32") Setback

Profile length

A

B

9 (11/32")


Blocking forframe applications

Min. topclearance


Drawer width

Ope

ning




37

(1-7

/16"

)

25 (15/16”)



System or #7 woodscrews

page 52


7 (9/32")

1 1 (7/ 1 6")



13 (1/2")





25 (31/32")

37 (1-7/16")

32 (1-1/4”)

33 (1-5/16”)

6 (1/4”)

9 (11/32”)

Profile close-up



TANDEM plus BLUMOTION Drawer length Minimum inside

cabinet depth Profile lengthScrew locations for panel cabinets

A B568F4570B 457 (18") 477 (18-3/4") 470 (18-1/2") 261 (10-1/4") 453 (17-13/16")568F5330B 533 (21") 553 (21-3/4") 546 (21-1/2") 261 (10-1/4") 517 (20-3/8")568A6100B 610 (24") 633 (24-15/16") 626 (24-11/16") 261 (10-1/4") 389 (15-5/16")568A6860B 686 (27") 703 (27-11/16") 696 (27-7/16") 261 (10-1/4") 389 (15-5/16")568A7620B 762 (30") 778 (30-5/8") 771 (30-3/8") 261 (10-1/4") 389 (15-5/16")

Calculating outside drawer widthFor drawer side thickness 19 (3/4") 18 (23/32") 17 (21/32") 16 (5/8") 15 (19/32")

Deduct from inside cabinet width 11 (7/16") 13 (15/32") 14 (9/16") 10 (3/8") 12 (15/32")




Two required per drawer █Depth and side-to-side self-alignment █Zinc-plated steel █For use with 552/562 █




Part no.

Part no.

Inset drawers


Profile setbackSee table on right pageTrial recommended

Blocking behind frame

Inside depth range

Minimum =profile length + setback + 6 (1/4")

Maximum with bracket =profile length + setback + 48 (1-15/16")

Profile setbackSee table on right pageTrial recommended

Blocking behind frame (heavy duty)

Inside depth range

Minimum =profile length + setback + 6 (1/4")

Requires increased setback of cabinet █profileFrame applications require blocking-out █behind face frame

Application Description

Applications

Basic components


Rear mounting bracketfor face frame only

The depth adjustable locking device is specially designed for inset applications to allow installers to perfectly align drawer fronts.



Offers █ 4 (3/16") out adjustment, preset at 0Designed for 1/2" bottom recess █Height adjustable █ +3 (1/8")For use with 562/568 █

Depth adjustable locking device (inset)

Frame cabinet Panel cabinet or heavy duty application

Right T51.1700.PV RLeft T51.1700.PV LInstallation screw 612TH


Installation

NOTE: For mounting hole position, add 6 mm to profile setback.

After installation, adjust the locking device until the drawer front is in the desired position (out adjustment only).

Setbacks shown are for drawer fronts that are flush with the face frame. For recessed drawer fronts or to allow for adjustability, the setback must be increased.

Mounting hole position

Profile setbackN

OTE

: R

unne

r can

not b

e m

ount

ed b

elow

ope

ning

Depth adjustment

Turning the adjustment screw, using a Phillips or POZI driver, allows for up to 4 (3/16") out adjustment.

Bottom recess

Drawer sub front thickness

Designed for a █ 13 (1/2") bottom recess13 █ (1/2") drawer sub front thickness

Mounting the TANDEM profile for inset application562H Profile setback

Sub

front

th

ickn

ess 13 (1/2") 18 21 24

16 (5/8") 21 24 2719 (3/4") 24 27 30

16 (5/8") 19 (3/4") 22 (7/8")Drawer front thickness

562F Profile setback

Sub

front

th

ickn

ess 13 (1/2") 15 18 21

16 (5/8") 18 21 2419 (3/4") 21 24 27

16 (5/8") 19 (3/4") 22 (7/8")Drawer front thickness

Narrow drawers


One right and one left required per drawer █Maximum load rating of 25 lb █For interior drawer widths of █ 95 (3-3/4") to 121 (4-3/4")Requires █ 13 (1/2") drawer bottom recessRequires █ 16 (5/8") min. sub front thicknessHeight adjustable █ +3 (1/8")For use with 552/562 █

For interior drawer widths of █ 95 (3-3/4") to 121 (4-3/4")Special narrow locking device required █Maximum load rating for narrow drawer █locking device is 25 lbMinimum █ 16 (5/8") drawer materialSingle or full extension █

Application Description Basic components


Rear mounting bracketfor face frame only

Components


Narrow drawer application is possible with any TANDEM, TANDEM plus or TANDEM plus BLUMOTION profile. See the installation instructions for the profile used.

Two required per drawer █Depth and side-to-side self-alignment █Zinc-plated steel █For use with 552/562 █



Narrow drawer locking device Rear mounting bracket for frame cabinets

Profile set

Right T51.0700.20 RLeft T51.0700.20 LInstallation screw 606N or 606P


Partial extension552H series page 16552F series page 18

Full extension

562H series page 21562F series page 23

Part no.

Part no.

16 (5/8”) min.

95 (3-3/4") to 121 (4-3/4")

7 (9/32")

11 (7/16")

Ø6 x 10 bore for hook


13 (1/2")



1. Position locking device in front corner of the drawer.

2. Pre-bore locking device mounting screw holes with Ø2 mm piloting bit.

3. Attach with two 606N or 606P screws.

4. Repeat on the other side.

NOTE: A minimum of 16 (5/8") drawer material is required for mounting the narrow drawer locking device.

Drawer back preparation

Attach locking devices

Possible with any TANDEM runner █Dynamic load capacity of 75 lb █

Description

Roll-out shelf13

(1/2

”)

X

Outside shelf width

Inside shelf width =Inside cabinet width - 42 (1-5/8”) for H

Inside cabinet width - 49 (1-15/16”) for F


8 (5/16”)

16 (5/8”)

20 (3/4”)

10 (13/32”)


Eliminates the need to edge bore holes █for hooks on roll-outs

Attach rear mounting block to the back of the shelf instead of notching and boring.

Basic componentsApplication

Components

One right and one left required per █drawerFor interior roll-out applications █Height adjustable █ +3 (1/8")For use with all TANDEM runners █

page 14Installation

For use when a precise stopping position is required.

Set side apron 1/8" from back shelf panel

Align inside of mounting block tip with insideedge of the apron

T51.1700.POPositive stop locking device for roll-out shelf applications


Positive stop locking device

Rear mounting block

Shelf assembly

Right T51.1700.PO RLeft T51.1700.PO LInstallation screw 612TH

Rear mounting block T51.7000Installation screw 606N or 606P

Shelf size and position in opening

Part no.

Part no.

Calculating outside tray widthApron

thickness (X) 19 (3/4") 18 (23/32") 17 (21/32") 16 (5/8") 15 (19/32") 14 (9/16") 13 (1/2") 12 (15/32")Deduct

from inside cabinet width

11 (7/16") 13 (15/32") 14 (9/16") 10 (3/8") 12 (15/32") 14 (9/16") 16 (5/8") 18 (23/32")

Bottom mount drawer

19.5(3/4") 30(1

-3/16

")

42(1

-5/8

”)


Possible with any TANDEM runner █Dynamic load capacity of up to 110 lb █


19.5 (3/4") 30(1

-3/1

6")

Screws612TH

Universal mounting

bracket

295.4000

page 5219.5 (3/4") 30

(1-3

/16")

Screws612TH

Universal mounting

bracket

295.4000

page 52

Drawer bottom mount installation Roll-out tray bottom mount installation

Dual mount application Standard locking device

page 14

Right T51.1700.04 RLeft T51.1700.04 LInstallation screw 612TH



Installation


SPACE CORNER


34

Use longer length heavy duty TANDEM █plus BLUMOTION runnersRequires special cabinet and drawer █construction (see note below)For █ 16 (5/8") max. drawer side material use TANDEM plus 568. seriesFor █ 19 (3/4") max. drawer side material use TANDEM plus 568A seriesDynamic load capacity of 110 lb █Static load capacity of 125 lb █


Components

Corner cabinet size

Max. 5/8" drawer sidethickness

Max. 3/4" drawer sidethickness

36", 39" or 42" 568.6860B 568A6860BNOTE: SPACE CORNER requires special cabinet and drawer construction. See suggestions on cabinet construction at www.blum.com.


Corner cabinet size

Subject to technical modifications without notice. © 2008

Profile set

Measuring corner cabinet size


page 14

Right T51.1700.04 R

Left T51.1700.04 LInstallation screw 612TH



Installation


A

B

Setback

Profile length

C

D

9 (11/32")

NOTE: Detailed drawings for cabinet construction are available at www.blum.com



Drawer construction

Mounting locations

For a 39" SPACE CORNER using 5/8" material and 568.6860B For a 39" SPACE CORNER using 3/4" material and 568A6860B

TANDEM plus BLUMOTION Drawer material Setback A B C D

568.6860B 16 (5/8") 108 (4-1/4") 114 (4-1/2") 141 (5-9/16") 365 (14-3/8") 493 (19-3/8") 568A6860B 19 (3/4") 117 (4-5/8") 123 (4-7/8") 150 (5-15/16") 374 (14-3/4") 502 (19-3/4")

110 lb.

TIP-ON for TANDEM plus

1click

2

Designed for drawers without pulls ■

Opens the drawer with just a touch ■of the drawer front

Tool-free attachment of mechanism ■and trigger to the cabinet profile

Performs best with loads up to 45 lb ■

Only works with TANDEM plus 562 H/F ■series runners without BLUMOTION

+-

+

-

Trigger allows in -3 (1/8") and out +2 (1/16") adjustment of the drawer front.


Assembly and adjustment

Runner profile

TIP-ON mechanism

Overlay application

Package contains:2 TIP-ON mechanisms2 adjustable triggers2 rear hook spacers

One set required per drawer T55.7150TIP-ON set

21

2

TIP-ON set

13

Step one — Attachment of mechanism Step two — Attachment of trigger

Step three — Attachment of rear hook spacer Step four — Adjustment

Subject to technical modifications without notice. © 2008

Part no.

36

3

12

Installation

Rear notching6

(1/4

”) m

in.

1 (1

/32”

) min

.

38(1

-1/2

”)

21 (13/16”)106 (4-3/16”)

6 (1

/4”)

min

. 1

(1/3

2”) m

in.

38(1

-1/2

”)

24.5 (15/16”)109.5 (4-5/16”)

7 (9/32")

11 (7/16")



13 (1/2”)

2.5 (3/32”)min.

TANDEM 562H dimensions TANDEM 562F dimensions

Minimum front gap Drawer back preparation

Dimensions in millimeters (inch equivalents as noted) 37

NOTE: Minimum cabinet opening for TIP-ON is 229 (9")

606N or 606PInstallation screw

ORGA-LINE Spice tray


Quick and easy removal of Spice tray █from cabinet High quality stainless steel combined with █wear resistant nylon parts in gray (R737)Form fitting locating tabs with anti-slip █surfaceContents visible due to angled surface █Dishwasher safe to 170° F █


Specifications

ZFZ.38G0I Spice tray set

120

(4-3

/4”)

282 (11-1/8”)

504 (19-7/8”)

190 (7-1/2”)

Dimensions Installation

Part no.

Part no.

Roll-out shelf application Standard drawer application

page 32 page 16

3 trays █

6 locating tabs █

Set contains:

a

Capacity

ORGA-LINE Knife holder

280180

60

606N or 606PInstallation screw



Attaches to ORGA-LINE utensil set or █drawer bottom High quality stainless steel combined with █wear resistant nylon parts in gray (R737)Holds up to 9 knives of varying sizes █Plastic and stainless steel construction █Four handle supports for large knives █Dishwasher safe to 170° F █

Specifications

Mounting to drawer bottom (attachment screws required)

Installation with ORGA-LINE set (no attachment screws required)

ZSZ.02M0 Knife holder set

4 includedMax. 9 knives

Designed to fit ZHI.533FI3A

Handle supports Dimensions

Part no.

Knife holder █4 handle supports █Locating tab █

Set contains:

1 2 3

a

ORGA-LINE

88 (3-1/2”)

264

(10-

3/8”

)

88 (3-1/2”)

88 (3-1/2”) 176

(7”)

88 (

3-1/

2”)

64 (2

-9/1

6”)

60 (2

-3/8

”)

88 (3-1/2”)


Application Description Use

ORGA-LINE flexible dividing system █High quality stainless steel utensil █dividers combined with wear resistant nylon parts in gray (R737)Removable cutlery trays, dishwasher safe █to 170o FSpring-loaded compensation tray and █side railsDesigned for drawer side thickness of █ 13 (1/2") to 19 (3/4")For █ 533 (21") or 457 (18") drawer lengths

16-1/4"to17"

Cutlery tray

Tray partition

End connector

Inside drawer length must be within this range for the spring-loaded side rails to fit properly.

Specifications

19-1/4"to20"

Compensation tray Side rail

Inside drawer length must be within this range for the spring-loaded side rails to fit properly.


Tray dimensions Set heights

Example of 21" drawer with ZHI.533BI3A Example of 18" drawer with ZHI.457GI3A

NOTE: For assembly instructions see page 56

Documents

Drawer and cabinet specifications