Embed Size (px)
Citation preview
Three-dimensional adjustment
Side adjustment Rotate the front cam screw to increase or decrease door overlay (+/- 1/16").
Height adjustment Loosen installation screws to adjust door position (+/- 1/8"), then retighten.
Depth adjustment Rotate the rear cam screw to adjust door gap (+ 3/32", - 1/32").
Door adjustment
Subject to technical modifications without notice. © 2011 Blum, Inc.
Drawer insertion Drawer removal 1. Squeeze orange handles on
locking devices2. Pull drawer straight out and up
1. Place drawer on runners and close. Locking devices will automatically connect to runners.
INST-TDM563F.03.12Subject to technical modifications without notice. © 2012 Blum, Inc.
New side adjustment New rear side adjustment2. After front side adjustment is made with the locking devices, rotate the rear side adjustment left or right to re-align the back of the drawer box with the front. Drawer back moves in the same direction as rotation.
R
L
R
L
drawerfront
1. Rotate side adjustment left or right equally on both locking devices. Drawer front moves in the same direction as rotation.
with locking device
Maximum 1.5 (1/16") to left or right (tool-free) Maximum 1.5 (1/16") to left or right (tool-free)
Height adjustment Tilt adjustmentRotate the tilt adjustment lever on the rear of each runner to tilt the top of the drawer front forward.
1. Press up on adjustment tab2. Push towards back of drawer
Maximum 5 (3/16") rise of drawer back (tool-free)Maximum 3 (1/8") rise of drawer front (tool-free) 1
2
New depth adjustment on runner
TANDEM 563 runners feature elongated holes that allow +/- 4.5 (3/16") depth adjustment.
Turning the adjustment screw allows for up to a + 2.5 (3/32") out adjustment
T51.1901.PSLocking device
with side, height and depth adjustment
New profile setback New bottom mounting
L
R
See blum.com for complete technical specifications and installation instructions.
3 (1/8")
X
67 (2-5/8")9 (11/32")
15.5
(5/8
")
22.5
(7/8
")
9 (11/32")32 (1-1/4") 37 (1-15/32")
10 (13/32")
37 (1-15/32")
setback 3 (1/8")
New depth adjustable locking device
Runner 563F5330B 563F4570B 563F3810B
X 448 (17-5/8") 378 (14-7/8") 319 (12-9/16")
TANDEM plus BLUMOTION 563F
T51.19xx
NOTE: Hole locations to the face of the cabinet stay the same. For inset applications see the TANDEM brochure
NOTE: For T51.1901.PS setback in inset applications, see the TANDEM brochure
NOTE: Side adjustment not available on T51.18xx locking devices
NOTE: Height adjustment available on all TANDEM locking devices
BAU0026482453 INDR 5633767 MA-580/0EN TAND 563F/A-B
BLUMOTION deactivation
Switch on the hinge cupFor small or light doors, the BLUMOTION can be deactivated on one of the hinges. COMPACT BLUMOTION comes in the activated position, marked with a “I”. The deactivated position is marked with a “0”.
Door must be closed once for the deactivation to be complete. To reactivate, move switch back to the original position “I”.
2
1
COMPACT BLUMOTION
Subject to technical modifications without notice. © 2011 Blum, Inc.LIT.HNG5501.04.11
Three-dimensional adjustment
Side adjustment
Rotate front screw to increase or decrease door overlay (±2 mm).
Height adjustment
Rotate cam screw on mounting plate to adjust door position (±2 mm).
On non-cam mounting plates, loosen screws, adjust door and retighten screws.
Depth adjustmentRotate rear spiral tech cam screw to adjust door gap (+3 mm, -2 mm).
BLUMOTION deactivation
BLUMOTIONinside
Deactivation switch on hinge cup
For small or light doors, the BLUMOTION can be deactivated on one of the hinges.
Door must be closed once for the deactivation to be complete. To reactivate, move switch back to original position.
1
2
Temperature information
CLIP top BLUMOTION is designed to be used at temperatures between 65° and 85° F. Lower or higher temperatures will not cause damage to the hinge, however they will affect the closing speed. Once the temperature returns to the suggested range the hinge will return to its optimal closing action.
Dimensions in millimeters (inch equivalents as noted) © 2012 Blum, Inc. 9
