86
Material Markup Language Public Review Draft 01, 06 June 2006 Document identifier: materials-matml-spec-pr-01 Location: http://docs.oasis-open.org/materials/ Editor: Brett Johanson, The Boeing Company <[email protected]> Contributors: J.G. (Gil) Kaufman, Individual Sally Fahrenholz-Mann,.ASM International Craig Seymour, Associate Member TC Members: Sally Fahrenholz-Mann, ASM International David Celznick, ASM International Fran Cverna, ASM International Craig Seymour, Individual Michael Mitchell, NASA Carlos Beauchamp, NIST Kent Reed, NIST Brett Johanson, The Boeing Company James Pillers, The Boeing Company David Goodall, Rolls-Royce, plc Abstract: This specification describes a standard XML format for the exchange of materials information. Information such as product form, heat treatment, mechanical properties and chemistry can be transmitted. Status: This document was last revised or approved by the OASIS Materials Markup Language TC on the above date. The level of approval is also listed above. Check the current location noted above for possible later revisions of this document. This document is updated periodically on no particular schedule. OASIS-materials-draft-spec-06-6-2006 06 June 2006 Copyright © OASIS Open 2006. All Rights Reserved. Page 1 of 86 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 2 3 4

docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  • Upload
    others

  • View
    15

  • Download
    0

Embed Size (px)

Citation preview

Page 1: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Material Markup LanguagePublic Review Draft 01, 06 June 2006Document identifier:

materials-matml-spec-pr-01

Location:http://docs.oasis-open.org/materials/

Editor:Brett Johanson, The Boeing Company <[email protected]>

Contributors:J.G. (Gil) Kaufman, IndividualSally Fahrenholz-Mann,.ASM InternationalCraig Seymour, Associate Member

TC Members:Sally Fahrenholz-Mann, ASM International David Celznick, ASM InternationalFran Cverna, ASM InternationalCraig Seymour, Individual Michael Mitchell, NASA Carlos Beauchamp, NIST Kent Reed, NIST Brett Johanson, The Boeing CompanyJames Pillers, The Boeing CompanyDavid Goodall, Rolls-Royce, plc

Abstract:This specification describes a standard XML format for the exchange of materials information. Information such as product form, heat treatment, mechanical properties and chemistry can be transmitted.

Status:This document was last revised or approved by the OASIS Materials Markup Language TC on the above date. The level of approval is also listed above. Check the current location noted above for possible later revisions of this document. This document is updated periodically on no particular schedule.Technical Committee members should send comments on this specification to the Technical Committee’s email list. Others should send comments to the Technical Committee by using the “Send A Comment” button on the Technical Committee’s web page at www.oasis-open.org/committees/materials.For information on whether any patents have been disclosed that may be essential to implementing this specification, and any offers of patent licensing terms, please refer to the Intellectual Property Rights section of the Technical Committee web page (www.oasis-open.org/committees/materials/ipr.php).The non-normative errata page for this specification is located at www.oasis-open.org/committees/materials.

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 1 of 68

1

2

3

45

67

89

10111213

1415161718192021222324

25262728

293031323334353637383940414243

12

3

Page 2: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Table of Contents1 Introduction............................................................................................................................ 4

1.1 Terminology.......................................................................................................................... 42 Schema Format...................................................................................................................... 5

2.1 Schema Format.................................................................................................................... 52.1.1 MatML_Doc................................................................................................................... 52.1.2 Associate....................................................................................................................... 52.1.3 AssociationDetails.........................................................................................................62.1.4 BulkDetails.................................................................................................................... 62.1.5 Characterization............................................................................................................72.1.6 ChemicalComposition...................................................................................................82.1.7 Class............................................................................................................................. 82.1.8 ComponentDetails.........................................................................................................92.1.9 Compound................................................................................................................... 102.1.10 Concentration............................................................................................................112.1.11 DataFormat...............................................................................................................112.1.12 DimensionalDetails....................................................................................................122.1.13 Element.....................................................................................................................122.1.14 Symbol...................................................................................................................... 132.1.15 Form.......................................................................................................................... 132.1.16 Formula.....................................................................................................................142.1.17 Geometry..................................................................................................................142.1.18 Glossary.................................................................................................................... 142.1.19 GlossaryTerm............................................................................................................152.1.20 Graphs......................................................................................................................152.1.21 Material.....................................................................................................................162.1.22 Metadata...................................................................................................................162.1.23 Name.........................................................................................................................172.1.24 Notes......................................................................................................................... 182.1.25 ParameterValue........................................................................................................182.1.26 PhaseComposition....................................................................................................192.1.27 ProcessingDetails......................................................................................................192.1.28 PropertyData.............................................................................................................202.1.29 Qualifier..................................................................................................................... 212.1.30 Relationship...............................................................................................................212.1.31 Source.......................................................................................................................222.1.32 Specification..............................................................................................................222.1.33 Uncertainty................................................................................................................222.1.34 Unit............................................................................................................................ 232.1.35 Unitless.....................................................................................................................242.1.36 Units..........................................................................................................................242.1.37 Value.........................................................................................................................24

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 2 of 68

44

4546474849505152535455565758596061626364656667686970717273747576777879808182838485

45

6

Page 3: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

2.1.38 AuthorityDetails.........................................................................................................252.1.39 DataSourceDetails....................................................................................................252.1.40 MeasurementTechniqueDetails.................................................................................262.1.41 ParameterDetails.......................................................................................................262.1.42 PropertyDetails..........................................................................................................272.1.43 SourceDetails............................................................................................................272.1.44 SpecimenDetails.......................................................................................................282.1.45 TestConditionDetails.................................................................................................282.1.46 ChemicalElementSymbol..........................................................................................292.1.47 CurrencyCode...........................................................................................................38

2.2 Character Styles.................................................................................................................533 References........................................................................................................................... 54

3.1 Normative........................................................................................................................... 54Appendix A. Acknowledgments....................................................................................................55Appendix B. Revision History........................................................................................................56Appendix C. Notices..................................................................................................................... 57Appendix D. Terminology Specifications and Materials Nomenclature.........................................58

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 3 of 68

8687888990919293949596979899100101102

103

78

9

Page 4: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

1 IntroductionThe materials markup language or MatML was initially developed by the National Institute of Standards and Technology (NIST). Prior versions to this work can be found on www.matml.org and are authored and edited by E.F. Begley on behalf of the MatML working group (1999-2001) and the MatML Steering Committee (2002).

The intent of this document is to standardize the way companies such as material suppliers, test houses, manufacturing companies and all other companies who use and depend on materials information exchange data.

1.1 TerminologyThe key words must, must not, required, shall, shall not, should, should not, recommended, may, and optional in this document are to be interpreted as described in [RFC2119]. For a list of terminology and recommended naming conventions for materials related data transmittal, refer to table 1 of appendix D.

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 4 of 68

104105106107108109110111112

113114115116117

1011

12

Page 5: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

2 Schema FormatThe following sections and subsections of this document outline the recommended format to be used in the electronic submission, transmission and collection of materials related information, properties and characteristics used in the materials industry.

2.1 Schema FormatFor schema code and other normative code, use the Code paragraph style. It fits 71 characters. For example:

- <xsd:schema xmlns:xsd="http://www.w3.org/2001/XMLSchema" elementFormDefault="qualified" attributeFormDefault="unqualified">- <!--

2.1.1 MatML_Doc This element declares the content model for MatML_Doc, topmost in the hierarchy of elements that comprise a document marked up using MatML. Content models describe the relationships of the element and its child elements. MatML_Doc must contain one or more Material elements. Metadata contains descriptions of the data sources, properties, measurement techniques, specimens, and parameters which are referenced when materials property data are encoded using other elements. Metadata may occur once or not at all within the Material element. For more information, see the documentation for the Metadata element.

The main element:  --> - <xsd:element name="MatML_Doc">- <xsd:annotation>  <xsd:documentation>

</xsd:documentation>   </xsd:annotation>- <xsd:complexType>- <xsd:sequence>  <xsd:element name="Material" type="Material" maxOccurs="unbounded" />   <xsd:element name="Metadata" type="Metadata" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>  </xsd:element>- <!--

2.1.2 AssociateThis element declares the content model for Associate, which contains a string representing a component's associate.OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 5 of 68

118119120121122

123124125126

127128129130

131

132133134135136137138139140

141

142143144145146147148149150151152153154155156157158

159

1601611621314

15

Page 6: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Type definitions follow:  --> - <xsd:simpleType name="Associate">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>  <xsd:restriction base="xsd:string" />   </xsd:simpleType>

2.1.3 AssociationDetails This element declares the content model for AssociationDetails, which contains a description of a relationship of the component to another component in a complex material system such as a composite, weld, or multilayer material. AssociationDetails is composed of the following elements. Associate contains the name of a component's associate. For example, a TiC coating has been placed on AISI 1018 steel coupons. The Associate of the steel, then, is the "titanium carbide coating." Associate must occur once and only once within the AssociationDetails element. Relationship contains a description of the relationship between a component and the associate. For example, the associate of the "steel" component is the "titanium carbide coating." The relationship of the "steel" to the "titanium carbide coating" is that the steel is the "substrate" for the coating. Relationship must occur once and only once within the AssociationDetails element. Notes contains any additional information concerning the association and may occur once or not at all within the AssociationDetails element.

- <xsd:complexType name="AssociationDetails">- <xsd:annotation>  <xsd:documentation> </xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Associate" type="Associate" minOccurs="0" />   <xsd:element name="Relationship" type="Relationship" minOccurs="0" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.4 BulkDetails This element declares the content model for BulkDetails, which contains a description of the bulk material and is composed of the following elements. Name contains the material's name and has one optional attribute, authority, for identifying an authoritative source of material names. Name must occur once and only once within the BulkDetails element. Class contains the material's class and may occur zero or more times within the BulkDetails element. Subclass contains the material's subclass(es) and may occur zero or more times within the BulkDetails element. Specification contains the material's specification(s) and has one optional attribute, authority, for identifying an authoritative source of material specifications. Specification may occur zero or more times within the BulkDetails element. Source contains the name of the source of the material and may occur once or not at all within the BulkDetails element. Form contains the form of the material and may occur once or not at all within the BulkDetails element. It has an optional

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 6 of 68

163

164

165166167168169170171172173

174

175176177178179180181182183184185186187188

189190191192193194195196197198199200

201

202203204205206207208209210211212213

1617

18

Page 7: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

element Geometry, for describing the dimensions of the Component. For additional information, see the documentation for the Form type. ProcessingDetails contains a description of a processing step for the material and may occur zero or more times within the BulkDetails element. For additional information, see the documentation for the ProcessingDetails element. Characterization contains the characterization of the material, including the formula, chemical composition, phase composition, and dimensional details. Characterization may occur once or not at all within the BulkDetails element. For additional information, see the documentation for the Characterization element. PropertyData contains the property data for the material and may occur zero or more times within the BulkDetails element. For additional information, see the documentation for the PropertyData element. Notes contains any additional information concerning the bulk material and may occur once or not at all within the BulkDetails element.

- <xsd:complexType name="BulkDetails">- <xsd:annotation>  <xsd:documentation> </xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Class" type="Class" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Subclass" type="Class" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Specification" type="Specification" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Source" type="Source" minOccurs="0" />   <xsd:element name="Form" type="Form" minOccurs="0" />   <xsd:element name="ProcessingDetails" type="ProcessingDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Characterization" type="Characterization" minOccurs="0" />   <xsd:element name="PropertyData" type="PropertyData" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.5 CharacterizationThis element declares the content model for Characterization, which contains a description of the chemical composition of the bulk material or component and is composed of the following elements. Formula contains a string representation of the chemical formula for the bulk material or component and must occur once and only once within the Characterization element. For further details see documentation of the Formula element. ChemicalComposition contains a description of the compounds and elements that comprise the bulk material or component and may occur once or not at all within the Characterization element. For additional information, see the documentation for the ChemicalComposition element. PhaseComposition contains a description of the phases that comprise the bulk material or component and may occur zero or more times within the Characterization element. For additional information, see the documentation for the PhaseComposition element. DimensionalDetails contains information relating to component or bulk material dimensional characteristics such as grain size, porosity, precipitate size and distribution, etc., and may occur zero or more times within the Characterization element. For additional information, see the documentation for the DimensionalDetails element. Notes contains any additional information concerning the Characterization and may occur once or not at all within the Characterization element.OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 7 of 68

214215216217218219220221222223224225

226227228229230231232233234235236237238239240241242243244245246247248249250

251

2522532542552562572582592602612622632642652662672681920

21

Page 8: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:complexType name="Characterization">- <xsd:annotation> <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Formula" type="Formula" />   <xsd:element name="ChemicalComposition" type="ChemicalComposition" minOccurs="0" />   <xsd:element name="PhaseComposition" type="PhaseComposition" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="DimensionalDetails" type="DimensionalDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.6 ChemicalComposition This element declares the content model for ChemicalComposition, which contains a detailed description of the compounds and elements that comprise the bulk material or component. ChemicalComposition must contain at least one Compound element or Element element but may contain as many of each element as needed. Compound contains a description of a compound. For additional information, see the documentation for the Compound element. Element contains a description of an element. For additional information, see the documentation for the Element element.

- <xsd:complexType name="ChemicalComposition">- <xsd:annotation>  <xsd:documentation> </xsd:documentation>   </xsd:annotation>- <xsd:choice maxOccurs="unbounded">  <xsd:element name="Compound" type="Compound" />   <xsd:element name="Element" type="Element" />   </xsd:choice>  </xsd:complexType>

2.1.7 Class This element declares the content model for Class, which is the material class to which the Material belongs. The Class can either have a Name or ParentMaterial element: Name contains a string representing the name of the material's class and may occur only once within the Class element. ParentMaterial is an reference by ID to another Material in the MatML_Doc and can occur only once in the Class element.

- <xsd:complexType name="Class">- <xsd:annotation> <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 8 of 68

269

270271272273274275276277278279280281282283284285286

287288289290291292293294295

296297298299300301302303304305306

307

308309310311312313314

315316317318319320

2223

24

Page 9: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:choice>  <xsd:element name="Name" type="Name" /> - <xsd:element name="ParentMaterial" minOccurs="0" maxOccurs="unbounded">- <xsd:complexType>  <xsd:attribute name="id" type="xsd:IDREF" use="required" />   </xsd:complexType>  </xsd:element>  </xsd:choice>  <xsd:element name="ParentSubClass" type="Class" minOccurs="0" maxOccurs="unbounded" />   </xsd:sequence>  </xsd:complexType>

2.1.8 ComponentDetailsThis element declares the content model for ComponentDetails, which contains a description of a component within the bulk material and has one optional attribute, id, which may be used as an identification specifier for the component and is especially useful for complex systems such as composite laminates. ComponentDetails is composed of the following elements. Name contains the component's name and has one optional attribute, authority, for identifying an authoritative source of component names. Name must occur once and only once within the ComponentDetails type. Class contains the component's class and may occur zero or more times within the ComponentDetails element. For additional information, see the documentation for the Class type. Subclass contains the component's subclass(es) and may occur zero or more times within the ComponentDetails element. For additional information, see the documentation for the SubClass type. Specification contains the component's specification(s) and has one optional attribute, authority, for identifying an authoritative source of component specifications. Specification may occur zero or more times within the ComponentDetails type. Source contains the name of the source of the component and may occur once or not at all within the ComponentDetails type. For additional information, see the documentation for the SourceDetails element. Form contains the form of the component and may occur once or not at all within the ComponentDetails type. It has an optional element Geometry, for describing the dimensions of the Component. For additional information, see the documentation for the Form type. ProcessingDetails contains a description of a processing step for the component and may occur zero or more times within the ComponentDetails type. For additional information, see the documentation for the ProcessingDetails element. Characterization contains the characterization of the component, including the formula, chemical composition, phase composition, and dimensional details. Characterization may occur once or not at all within the ComponentDetails type. For additional information, see the documentation for the Characterization element. PropertyData contains the property data for the component and may occur zero or more times within the ComponentDetails type. For additional information, see the documentation for the PropertyData element. AssociationDetails contains a description of a relationship of the component to another component and may occur zero or more times within the ComponentDetails type. For additional information, see the documentation for the AssociationDetails element. Notes contains any additional information concerning the component and may occur once or not at all within the ComponentDetails type. ComponentDetails contains a description of a component within the component and is used to support encoding of information for complex materials systems such as composites. ComponentDetails may occur zero or more times within a ComponentDetails element.

- <xsd:complexType name="ComponentDetails">- <xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 9 of 68

321322323324325326327328329330331332333334

335

336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371

372373

2526

27

Page 10: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

 <xsd:documentation>

</xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Class" type="Class" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Subclass" type="Class" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Specification" type="Specification" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Source" type="Source" minOccurs="0" />   <xsd:element name="Form" type="Form" minOccurs="0" />   <xsd:element name="ProcessingDetails" type="ProcessingDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Characterization" type="Characterization" minOccurs="0" />   <xsd:element name="PropertyData" type="PropertyData" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="AssociationDetails" type="AssociationDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="ComponentDetails" type="ComponentDetails" minOccurs="0" maxOccurs="unbounded" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="optional" />   </xsd:complexType>

2.1.9 CompoundThis element declares the content model for Compound, which contains the elemental description of a chemical compound and is composed the following elements. Element contains the description of a chemical element and must occur one or more times within the Compound element. For additional information, see the documentation for the Element element. Concentration contains the concentration of the compound and may occur once or not at all within the Compound element. For additional information, see the documentation for the Concentration element. Notes contains any additional information concerning the compound and may occur once or not at all within the Compound element.

- <xsd:complexType name="Compound">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Element" type="Element" maxOccurs="unbounded" />   <xsd:element name="Concentration" type="Concentration" minOccurs="0" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 10 of 68

374375376377378379380381382383384385386387388389390391392393394395396397398399400401

402

403404405406407408409410411412

413414415416417418419420421422423424425

426

2829

30

Page 11: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

2.1.10 ConcentrationThis element declares the content model for Concentration and is composed of the following elements. Value contains the value of the concentration and has one required attribute, format, for indicating the format of the value. Value must occur once and only once within the Concentration element. Units contains the units for the value of the concentration and must occur once and only once within the Concentration element. For additional information, see the documentation for the Units element. Qualifier contains any qualifier pertinent to the value of the concentration (e.g. "min," "max," etc.) and may occur once or not at all within the Concentration element. Uncertainty contains the measurement uncertainty(ies) of the data in Data and may occur zero or more times within the Concentration element. For additional information, see the documentation for the Uncertainty type. Notes contains any additional information concerning the concentration and may occur once or not at all within the Concentration element.

- <xsd:complexType name="Concentration">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Value" type="Value" />   <xsd:element name="Units" type="Units" />   <xsd:element name="Qualifier" type="Qualifier" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Uncertainty" type="Uncertainty" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.11 DataFormatThis element declares the content model for DataFormat and is composed of the following elements. DataFormat is used to indicate the format of a value with which it is associated ("float," "integer," "string,", "exponential" or "mixed") "mixed" is only used for a group of data where each individual member of the group can be given a unique format.

- <xsd:simpleType name="DataFormat">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:restriction base="xsd:string">  <xsd:enumeration value="float" />   <xsd:enumeration value="integer" />   <xsd:enumeration value="string" />   <xsd:enumeration value="exponential" />   <xsd:enumeration value="mixed" />   </xsd:restriction>  </xsd:simpleType>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 11 of 68

427428429430431432433434435436437438439

440441442443444445446447448449450451452453454455456

457

458459460461462463

464465466467468469470471472473474475476477

478

3132

33

Page 12: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

2.1.12 DimensionalDetailsThis element declares the content model for DimensionalDetails, which contains a description of a dimensional characteristic (e.g. grain size, porosity, precipitate size and distribution, etc.) of the bulk material or component and is composed of the following elements. Name contains the name of the characteristic and has one optional attribute, authority, for identifying an authoritative source of dimensional characteristic names. Name must occur once and only once within the DimensionalDetails element. Value contains the value of the dimensional characteristic and has one required attribute, format, for indicating the format of the value. Value must occur once and only once within the DimensionalDetails element. Units contains the units for the value of the dimensional characteristic and must occur once and only once within the DimensionalDetails element. For additional information, see the documentation for the Units type. Qualifier contains any qualifier pertinent to the value of the dimensional characteristic (e.g. "min," "max," etc.) and may occur once or not at all within the DimensionalDetails element. Uncertainty contains the measurement uncertainty(ies) of the data in Data and may occur zero or more times within the DimensionalDetails element. For additional information, see the documentation for the Uncertainty type. Notes contains any additional information concerning the dimensional characteristic and may occur once or not at all within the DimensionalDetails element.

- <xsd:complexType name="DimensionalDetails">- <xsd:annotation> <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Value" type="Value" />   <xsd:element name="Units" type="Units" />   <xsd:element name="Qualifier" type="Qualifier" minOccurs="0" />   <xsd:element name="Uncertainty" type="Uncertainty" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.13 ElementThis element declares the content model for Element and is composed of the following elements. Symbol contains the symbol for the chemical element, which is one among those enumerated by the ChemicalElementSymbol datatype. Symbol has one optional attribute, subscript, for indicating the subscript (formula units) of the chemical element. Symbol must occur once and only once within the Element element. For additional information, see the documentation for the ChemicalElementSymbol datatype. Concentration contains the concentration of the element and may occur once or not at all within the Element element. For additional information, see the documentation for the Concentration element. Notes contains any additional information concerning the element and may occur once or not at all within the Element element.

- <xsd:complexType name="Element">- <xsd:annotation> <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 12 of 68

479480481482483484485486487488489490491492493494495496

497498499500501502503504505506507508509510511512

513

514515516517518519520521522523524

525526527528529530531

3435

36

Page 13: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

2.1.14 SymbolThis element declares the content model for Symbol, which contains the symbol for the chemical element. The entry for Symbol is selected from among the strings enumerated by the ChemicalElementSymbol datatype. Symbol has one optional attribute, subscript, for indicating the subscript (formula units) of the chemical element.

- <xsd:element name="Symbol">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:complexType>- <xsd:simpleContent>- <xsd:extension base="ChemicalElementSymbol">  <xsd:attribute name="subscript" type="xsd:string" use="optional" default="1" />   </xsd:extension>  </xsd:simpleContent>  </xsd:complexType>  </xsd:element>  <xsd:element name="Concentration" type="Concentration" minOccurs="0" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.15 FormThis element declares the content model for Form, which contains a description of the form of the bulk material or component. It also contains an element to describe the geometry of the the form and an element for any notes. For additional information, see the documentation for the Geometry element.

- <xsd:complexType name="Form">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Description" type="Name" />   <xsd:element name="Geometry" type="Geometry" minOccurs="0" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 13 of 68

532

533534535536537538

539540541542543544545546547548549550551552553554555556557558

559

560561562563564565

566567568569570571572573574575576577578

579580581

3738

39

Page 14: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

2.1.16 FormulaFormula contains a string representation of the chemical formula for the bulk material or component and must occur once and only once within the Characterization element.

- <xsd:simpleType name="Formula">- <xsd:annotation> <xsd:documentation></xsd:documentation>   </xsd:annotation>  <xsd:restriction base="xsd:string" />   </xsd:simpleType>

2.1.17 GeometryThis element declares the content model for Geometry, which contains a description of the geometry of the bulk material, component or specimen and is composed of the following elements. Shape is a string describing the shape of the bulk material or component and must occur once and only once within the Geometry element. Dimensions is a string describing the dimensions of the bulk material or component and may occur once or not at all within the Geometry element. Orientation is a string describing the orientation of the bulk material or component and may occur once or not at all within the Geometry element. Notes contains any additional information concerning the geometry and may occur once or not at all within the Geometry element.

- <xsd:complexType name="Geometry">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Shape" type="xsd:string" />   <xsd:element name="Dimensions" type="xsd:string" minOccurs="0" />   <xsd:element name="Orientation" type="xsd:string" minOccurs="0" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.18 GlossaryThis element declares the content model for Glossary, which contains descriptions of material and property terms used in the document. Glossary must contain one or more Term elements.

- <xsd:complexType name="Glossary">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Term" type="GlossaryTerm" maxOccurs="unbounded" />

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 14 of 68

582583584585

586587588589590591592

593

594595596597598599600601602603604

605606607608609610611612613614615616617

618619

620621622623

624625626627628629630

4041

42

Page 15: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:sequence>  </xsd:complexType>

2.1.19 GlossaryTermThis element declares the content model for GlossaryTerm which is composed of the following elements. Name contains the term's name and has one optional attribute, authority, for identifying an authoritative source of terms. Name must occur once and only once within the Term element. Definition contains the term's definition and must occur once and only once within the Term element. Abbreviation contains the term's abbreviations and may occur zero or more times within the Term element. Synonym contains the term's synonyms and may occur zero or more times within the Term element. Notes contains any additional information concerning the term and may occur once or not at all within the Term element.

- <xsd:complexType name="GlossaryTerm">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Definition" type="xsd:string" />   <xsd:element name="Abbreviation" type="xsd:string" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Synonym" type="xsd:string" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.20 GraphsThis element declares the content model for Graphs, which must contain one or more Graph elements. Graph uses the W3C's Scalable Vector Graphics markup language (SVG) for describing two dimensional graphics and allows for three types of graphical objects: vector graphics shapes, images, and text. Graph must occur one or more times within the Graphs element. For more information concerning SVG, see the documentation at http://www.w3.org/TR/SVG/.

- <xsd:complexType name="Graphs">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence maxOccurs="unbounded">- <xsd:element name="Graph">- <xsd:complexType>- <xsd:sequence>  <xsd:any namespace="http://www.w3.org/2000/svg" processContents="lax" maxOccurs="unbounded" />   </xsd:sequence>  </xsd:complexType>  </xsd:element>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 15 of 68

631632

633

634635636637638639640641642643

644645646647648649650651652653654655656657658659

660

661662663664665666667668

669670671672673674675676677678679680681682

4344

45

Page 16: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:sequence>  </xsd:complexType>

2.1.21 MaterialThis element declares the content model for Material, which contains materials data. Material has three optional attributes. The first attribute, id, may be used as an identification specifier for the material, which is especially useful for complex systems such as composite laminates. The second attribute, layers, may be used to indicate the number of layers in complex systems such as composite laminates. The third attribute, local_frame_of_reference, may be used as an identification specifier for the local material orientation relative to the global frame of reference, which is especially useful for complex systems such as anisotropic materials. Material is composed of the following elements. BulkDetails contains a description of the bulk material and must occur once and only once within the Material element. For additional information, see the documentation for the BulkDetails element. ComponentDetails contains a description of a component within the bulk material and may occur zero or more times within the Material element. ComponentDetails may be used to describe complex materials systems such as welds (e.g. the base metal, the heat affected zone, and the weld metal) or composites (e.g. the whiskers, fibers, and matrix of a fiber-reinforced composite material). For additional information, see the documentation for the ComponentDetails element. Graphs contains descriptions of two dimensional graphics and may occur once or not at all within the Material element. For additional information, see the documentation for the Graphs element. Glossary contains descriptions of the material and property terms used in the document and may occur once or not at all within the Material element. For additional information, see the documentation for the Glossary element.

- <xsd:complexType name="Material">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="BulkDetails" type="BulkDetails" />   <xsd:element name="ComponentDetails" type="ComponentDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Graphs" type="Graphs" minOccurs="0" />   <xsd:element name="Glossary" type="Glossary" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="optional" />   <xsd:attribute name="layers" type="xsd:integer" use="optional" />   <xsd:attribute name="local_frame_of_reference" type="xsd:string" use="optional" />   </xsd:complexType>

2.1.22 MetadataThis element declares the content model for Metadata, which contains descriptions of authorities, data sources, measurement techniques, parameters, properties, material and component sources, specimens, and test conditions. Metadata is composed of the following elements. AuthorityDetails contains a description of authorities referenced from the Specification and Name elements and may occur zero or more times within the Metadata element. For additional information, see the documentation for the AuthorityDetails element. DataSourceDetails contains a description of a data source referenced using the PropertyData element and may occur zero or OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 16 of 68

683684685

686

687688689690691692693694695696697698699700701702703704705706707

708709710711712713714715716717718719720721722723724725

726

7277287297307317327337344647

48

Page 17: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

more times within the Metadata element. For additional information, see the documentation for the DataSourceDetails element. MeasurementTechniqueDetails contains a description of a measurement technique referenced using the PropertyData element and may occur zero or more times within the Metadata element. For additional information, see the documentation for the MeasurementTechniqueDetails element. ParameterDetails contains a description of a parameter referenced using the PropertyData element and may occur zero or more times within the Metadata element. For additional information, see the documentation for the ParameterDetails element. PropertyDetails contains a description of a property for which materials data are encoded using the PropertyData element and may occur zero or more times within the Metadata element. For additional information, see the documentation for the PropertyDetails element. SourceDetails contains a description of the source of a material or component referenced using the Source element and may occur zero or more times within the Metadata element. For additional information, see the documentation for the SourceDetails element. SpecimenDetails contains a description of a specimen referenced using the PropertyData element and may occur zero or more times within the Metadata element. For additional information, see the documentation for the SpecimenDetails element. TestCondtionDetails contains a description of the test condtion(s) referenced using the PropertyData element and may occur zero or more times within the Metadata element. For additional information, see the documentation for the TestCondtionDetails element.

- <xsd:complexType name="Metadata">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="AuthorityDetails" type="AuthorityDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="DataSourceDetails" type="DataSourceDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="MeasurementTechniqueDetails" type="MeasurementTechniqueDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="ParameterDetails" type="ParameterDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="PropertyDetails" type="PropertyDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="SourceDetails" type="SourceDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="SpecimenDetails" type="SpecimenDetails" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="TestConditionDetails" type="TestConditionDetails" minOccurs="0" maxOccurs="unbounded" />   </xsd:sequence>  </xsd:complexType>

2.1.23 NameThis element declares the content model for Name, which contains a string representing a name and has one optional attribute, authority, for identifying an authoritative source of names in the context in which the Name element is used.

- <xsd:complexType name="Name">- <xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 17 of 68

735736737738739740741742743744745746747748749750751752753754

755756757758759760761762763764765766767768769770771772773774775776777778779780

781

782783784785786

787788

4950

51

Page 18: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:simpleContent>- <xsd:extension base="xsd:string">  <xsd:attribute name="authority" type="xsd:IDREF" use="optional" />   </xsd:extension>  </xsd:simpleContent>  </xsd:complexType>

2.1.24 Notes This element declares the content model for Notes, which contains a string representing descriptive notes.

- <xsd:simpleType name="Notes">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>  <xsd:restriction base="xsd:string" />   </xsd:simpleType>

2.1.25 ParameterValueThis element declares the content model for ParameterValue, which contains the value of a parameter. ParameterValue has two required attributes. The first attribute, parameter, references an id attribute specified in a ParameterDetails element so that the descriptive details of the parameter are tied to the value. The second attribute, format, indicates the format of the value. If used, "mixed" indicates that the not all of the parameter values are of the same type (e.g. a "No Break" value for an otherwise numeric set of Charpy Izod test results). If used, then the "format" attribute on each "Data" item should be individually set. ParameterValue is composed of the following elements. Data contains the property data and has one required attribute, format, for indicating the format of the data. Data must occur once and only once within the ParameterValue element. Qualifier contains any qualifier(s) pertinent to the data in ParameterValue(e.g. "min," "max," etc.) and may occur zero or more times within the PropertyData element. Uncertainty contains the measurement uncertainty(ies) of the data in ParameterValue and may occur once or not at all within the ParameterValue element. For additional information, see the documentation for the Uncertainty element. Notes contains any additional information concerning the property data and may occur once or not at all within the PropertyData element.

- <xsd:complexType name="ParameterValue">- <xsd:annotation> <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>- <xsd:element name="Data">- <xsd:complexType>- <xsd:simpleContent>- <xsd:extension base="xsd:string">  <xsd:attribute name="format" type="DataFormat" use="optional" />

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 18 of 68

789790791792793794795796797798

799

800801802803

804805806807808809810

811

812813814815816817818819820821822823824825826827828

829830831832833834835836837838839

5253

54

Page 19: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:extension>  </xsd:simpleContent>  </xsd:complexType>  </xsd:element>  <xsd:element name="Uncertainty" type="Uncertainty" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Qualifier" type="Qualifier" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="parameter" type="xsd:IDREF" use="required" />   <xsd:attribute name="format" type="DataFormat" use="required" />   </xsd:complexType>

2.1.26 PhaseCompositionThis element declares the content model for PhaseComposition, which contains a description of a phase that comprises the bulk material or component and is composed of the following elements. Name contains the name of the phase and has one optional attribute, authority, for identifying an authoritative source of phase names. Name must occur once and only once within the PhaseComposition element. Concentration contains the concentration of the phase and may occur once or not at all within the PhaseComposition element. For additional information, see the documentation for the Concentration element. PropertyData contains property data for the phase and may occur zero or more times within the PhaseComposition element. For additional information, see the documentation for the PropertyData element. Notes contains any additional information concerning the phase and may occur once or not at all within the PhaseComposition element.

- <xsd:complexType name="PhaseComposition">- <xsd:annotation> <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Concentration" type="Concentration" minOccurs="0" />   <xsd:element name="PropertyData" type="PropertyData" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.27 ProcessingDetailsThis element declares the content model for ProcessingDetails, which contains a description of a processing step for the bulk material or component. ProcessingDetails is composed of the following elements. Name contains the name of the processing step and has one optional attribute, authority, for identifying an authoritative source of processing step names. Name must occur once and only once within the ProcessingDetails element. ParameterValue contains the value of a parameter under which the processing step occurred and may occur zero or more

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 19 of 68

840841842843844845846847848849850851852853

854855

856857858859860861862863864865866867868

869870871872873874875876877878879880881882883

884

885886887888889890891

5556

57

Page 20: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

times within the ProcessingDetails element. For additional information, see the documentation for the ParameterValue element. Result is a string that contains a description of the outcome or result of the processing step and may occur once or not at all within the ProcessingDetails element. Notes contains any additional information concerning the processing step and may occur once or not at all within the ProcessingDetails element.

- <xsd:complexType name="ProcessingDetails">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="ParameterValue" type="ParameterValue" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Result" type="xsd:string" minOccurs="0" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  </xsd:complexType>

2.1.28 PropertyDataThis element declares the content model for PropertyData, which contains property data. PropertyData has seven attributes. The first attribute, property, is required and references an id attribute specified in a PropertyDetails element so that the descriptive details for the property are tied to the data found in the Data element. The second attribute, technique, is optional and references an id attribute Specified in a MeasurementTechniqueDetails element so that the Descriptive details for the measurement technique are tied to the data found In the Data element. The third attribute, source, is optional and references an id attribute specified in a DataSourceDetails element so that the descriptive details for the data source are tied to the data found in the Data element. The fourth attribute, specimen, is optional and references an id attribute specified in a SpecimenDetails element so that the descriptive details for the specimen are tied to the data found in the Data element. The fifth attribute, test, is optional and references an id attribute specified in a TestCondtionDetails element so that the descriptive details for the test condition(s) are tied to the data found in the Data element. The sixth attribute, delimiter, specifies the delimiter that separates multiple values in the Data, Qualifier, Uncertainty, and ParameterValue elements. The default value is a comma (',') The seventh attribute, quote, specifies the string that is used to quote values in the Data, Qualifier, Uncertainty and ParameterValue elements. The default value is a null string, which is equivalent to saying that the values are not quoted. PropertyData is composed of the following elements. Data contains the property data and has one required attribute, format, for indicating the format of the data. Data must occur once and only once within the PropertyData element. Qualifier contains any qualifier(s) pertinent to the data in Data (e.g. "min," "max," etc.) and may occur once or not at all within the PropertyData element. Uncertainty contains the measurement uncertainty(ies) of the data in Data and may occur once or not at all within the PropertyData element. For additional information, see the documentation for the Uncertainty element. ParameterValue contains the value(s) of a parameter under which the data were determined and may occur zero or more times within the PropertyData element. For additional information, see the documentation for the ParameterValue element. Notes contains any additional information concerning the property data and may occur once or not at all within the PropertyData element. Note - Multiple entries in the Data, Qualifier, Uncertainty Value, and ParameterValue elements must be comma delimited and synchronized across elements, i.e., the number of entries in each of these four elements must be equal.

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 20 of 68

892893894895896897

898899900901902903904905906907908909910

911

912913914915916917918919920921922923924925926927928929930931932933934935936937938939940941942943944

5859

60

Page 21: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

 - <xsd:complexType name="PropertyData">- <xsd:annotation>  <xsd:documentation></xsd:documentation> </xsd:annotation>- <xsd:sequence>- <xsd:element name="Data">- <xsd:complexType>- <xsd:simpleContent>- <xsd:extension base="xsd:string">  <xsd:attribute name="format" type="DataFormat" use="required" />   </xsd:extension>  </xsd:simpleContent>  </xsd:complexType>  </xsd:element>  <xsd:element name="Uncertainty" type="Uncertainty" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Qualifier" type="Qualifier" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="ParameterValue" type="ParameterValue" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="property" type="xsd:IDREF" use="required" />   <xsd:attribute name="technique" type="xsd:IDREF" />   <xsd:attribute name="source" type="xsd:IDREF" />   <xsd:attribute name="specimen" type="xsd:IDREF" />   <xsd:attribute name="test" type="xsd:IDREF" /> - <xsd:attribute name="delimiter" default=",">- <xsd:simpleType>- <xsd:restriction base="xsd:string">  <xsd:minLength value="1" />   <xsd:whiteSpace value="preserve" />   </xsd:restriction>  </xsd:simpleType>  </xsd:attribute>  <xsd:attribute name="quote" type="xsd:string" />   </xsd:complexType>

2.1.29 QualifierThis element declares the content model for Qualifier, which contains a string representing a qualifier.

- <xsd:simpleType name="Qualifier">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>  <xsd:restriction base="xsd:string" />   </xsd:simpleType>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 21 of 68

945

946947948949950951952953954955956957958959960961962963964965966967968969970971972973974975976977978979980981982983

984

985986987988

989990991992993994995996

997

6162

63

Page 22: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

2.1.30 RelationshipThis element declares the content model for Relationship, which contains a string representing the relationship between a component and the associate.

- <xsd:simpleType name="Relationship">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>  <xsd:restriction base="xsd:string" />   </xsd:simpleType>

2.1.31 SourceThis element declares the content model for Source, which contains an id attribute specified in a SourceDetails element representing the source of the bulk material or component.

- <xsd:complexType name="Source">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>  <xsd:attribute name="source" type="xsd:IDREF" use="optional" />   </xsd:complexType>

2.1.32 SpecificationThis element declares the content model for Specification, which contains a string representing the specification for the bulk material or component and has one optional attribute, authority, for identifying an authoritative source of specifications.

- <xsd:complexType name="Specification">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:simpleContent>- <xsd:extension base="xsd:string">  <xsd:attribute name="authority" type="xsd:IDREF" use="optional" />   </xsd:extension>  </xsd:simpleContent>  </xsd:complexType>

2.1.33 UncertaintyThis element declares the content model for Uncertainty, which contains a description of the measurement uncertainty of the data. Uncertainty has 1 optional attributes: Name is a description of the nature of the uncertainty value, for example '6 sigma', 'Gaussian' or '2 std dev.' Uncertainty is composed of the following elements. Value contains the value of the uncertainty and has one required attribute, format, for indicating the format of the value. Value must occur once and only

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 22 of 68

99899910001001

1002100310041005100610071008

1009

1010101110121013

1014101510161017101810191020

1021

10221023102410251026

10271028102910301031103210331034103510361037

1038

103910401041104210431044

6465

66

Page 23: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

once within the Uncertainty element. Units contains the units for the value of the uncertainty and must occur once and only once within the Uncertainty element. For additional information, see the documentation for the Units element. Percentile is a value indicating the percentage of the data population that have values less than or equal to that expressed by the Uncertainty value. Percentile can occur sero or more times. If Percentile is not given then Value is interpreted as being an equal and unspecified deviation above and below the Property value(s). An uncertainty of 2 standard deviations below the mean for a normally distributed dataset would have a uncertainty percentile of 5%, and 2 standard deviations above the mean would be 95%. Notes contains any additional information concerning the uncertainty, such as a description of the evaluation of the uncertainty, and may occur once or not at all within the Uncertainty element.

- <xsd:complexType name="Uncertainty">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Value" type="Value" /> - <xsd:choice>  <xsd:element name="Units" type="Units" />   <xsd:element name="Unitless" type="Unitless" />   </xsd:choice>  <xsd:element name="Notes" type="Notes" minOccurs="0" /> - <xsd:element name="Scale" default="Linear" minOccurs="0">- <xsd:simpleType>- <xsd:restriction base="xsd:string">  <xsd:enumeration value="Linear" />   <xsd:enumeration value="Logarithmic" />   </xsd:restriction>  </xsd:simpleType>  </xsd:element>  </xsd:sequence>  <xsd:attribute name="DistributionType" type="xsd:string" use="optional" default="Normal/Gaussian" />   <xsd:attribute name="Num_Std_Dev" type="xsd:float" use="optional" default="2" />   <xsd:attribute name="Percentile" type="xsd:float" use="optional" />   <xsd:attribute name="ConfidenceLevel" type="xsd:float" use="optional" />   </xsd:complexType>

2.1.34 UnitThis element declares the content model for Unit, which contains a unit and has two optional attributes. The first attribute, power, is used to indicate the exponent for Unit. The second attribute, description, is used to describe Unit. Note - Multiple Unit elements are multiplied together to form units. Division is specified by setting the power attribute of Unit equal to "-1." For additional information, see the documentation for the Units element. Unit has a choice between two elements: Name is the Name of the unit, and can occur only once in the Unit element. Currency is the CurrencyCode for the unit, if it is a unit expressing cost in an ISO 4217 recognised currency.

- <xsd:complexType name="Unit">- <xsd:annotation>  <xsd:documentation></xsd:documentation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 23 of 68

10451046104710481049105010511052105310541055

10561057105810591060106110621063106410651066106710681069107010711072107310741075107610771078107910801081108210831084

1085

1086108710881089109010911092109310941095

1096109710981099

6768

69

Page 24: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:annotation>- <xsd:choice>  <xsd:element name="Name" type="xsd:string" />   <xsd:element name="Currency" type="CurrencyCode" />   </xsd:choice>  <xsd:attribute name="power" type="xsd:decimal" />   <xsd:attribute name="description" type="xsd:string" />   </xsd:complexType>

2.1.35 Unitless This element declares the content model for Unitless, which is an empty element used whenever a property, parameter, or uncertainty value has no units.

- <xsd:complexType name="Unitless">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>  </xsd:complexType>

2.1.36 Units This element declares the content model for Units, which contains units and has four optional attributes. The first attribute, system, is used to indicate the units system, such as "SI." The second attribute, factor, is used to indicate a constant multiplier in floating point format. The third attribute, name, is used to indicate the name of the units The fourth attribute, description, is used to describe the units. Units is composed of the following elements. Unit contains a unit and must occur one or more times within the Units element. For additional information, see the documentation for the Unit element. Note - Multiple Unit elements are multiplied together to form the units. Division is specified by using setting the power attribute of Unit equal to "-1."

- <xsd:complexType name="Units">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Unit" type="Unit" maxOccurs="unbounded" />   </xsd:sequence>  <xsd:attribute name="system" type="xsd:string" />   <xsd:attribute name="factor" type="xsd:float" />   <xsd:attribute name="name" type="xsd:string" />   <xsd:attribute name="description" type="xsd:string" />   </xsd:complexType>

2.1.37 Value This element declares the content model for value, which contains a string representing a value. Value has one required attribute, format, for indicating the format of the value.

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 24 of 68

11001101110211031104110511061107

1108

1109111011111112

111311141115111611171118

1119

1120112111221123112411251126112711281129

1130113111321133113411351136113711381139114011411142

1143

1144114511461147

7071

72

Page 25: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:complexType name="Value">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:simpleContent>- <xsd:extension base="xsd:string">  <xsd:attribute name="format" type="DataFormat" use="required" />   </xsd:extension>  </xsd:simpleContent>  </xsd:complexType>

2.1.38 AuthorityDetails This element declares the content model for AuthorityDetails, which contains a description of an authority referenced by other elements, such as the Specification and Name elements. An authority is typically an organisation that is the authoritative source of information about the element that is referencing it. AuthorityDetails has one required attribute, id, which may be arbitrarily assigned but must be unique among id attributes assigned elsewhere in a MatML document. AuthorityDetails additionally has two elements, Name and Notes. Name contains the name of the Authority. Name must occur once and only once within the AuthorityDetails element. Notes contains any additional information concerning the parameter and may occur once or not at all within the AuthorityDetails element.

- <!-- MetaData Type Definitions follow   --> - <xsd:complexType name="AuthorityDetails">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="required" />   </xsd:complexType>

2.1.39 DataSourceDetails This element declares the content model for DataSourceDetails, which contains a description of a data source referenced by the PropertyData element. DataSourceDetails has one required attribute, id, which may be arbitrarily assigned but must be unique among id attributes assigned elsewhere in a MatML document. DataSourceDetails also has one optional attribute, type, for specifying the type of the data source (examples include "unpublished report," "journal," "handbook," etc.) DataSourceDetails is composed of the following elements. Name contains the name of the data source and has one optional attribute, authority, for identifying an authoritative source of data source names. Name must occur once and only once within the DataSourceDetails element. Notes contains any additional information concerning the data source and may occur once or not at all within the DataSourceDetails element.

- <xsd:complexType name="DataSourceDetails">OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 25 of 68

11481149115011511152115311541155115611571158

1159

11601161116211631164116511661167116811691170

11711172

117311741175117611771178117911801181118211831184

1185

118611871188118911901191119211931194119511961197

1198

7374

75

Page 26: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="required" />   <xsd:attribute name="type" type="xsd:string" use="optional" />   </xsd:complexType>

2.1.40 MeasurementTechniqueDetails This element declares the content model for MeasurementTechniqueDetails, which contains a description of a measurement technique referenced by the PropertyData element. MeasurementTechniqueDetails has one required attribute, id, which may be arbitrarily assigned but must be unique among id attributes assigned elsewhere in a MatML document. MeasurementTechniqueDetails is composed of the following elements. Name contains the name of the measurement technique and has one optional attribute, authority, for identifying an authoritative source of measurement techniques. Name must occur once and only once within the MeasurementTechniqueDetails element. Notes contains any additional information concerning the measurement technique, such as a description of the technique, and may occur once or not at all within the MeasurementTechniqueDetails element.

- <xsd:complexType name="MeasurementTechniqueDetails">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="required" />   </xsd:complexType>

2.1.41 ParameterDetails This element declares the content model for ParameterDetails, which contains a description of a parameter referenced by the ParameterValue element. ParameterDetails has one required attribute, id, which may be arbitrarily assigned but must be unique among id attributes assigned elsewhere in a MatML document. ParameterDetails is composed of the following elements. Name contains the name of the parameter and has one optional attribute, authority, for identifying an authoritative source of parameter names. Name must occur once and only once within the ParameterDetails element. Units and Unitless are mutually exclusive elements for describing the parameter's units. Units or Unitless must occur once and only once within the ParameterDetails element. For additional information, see the documentation for the Units and Unitless elements. Notes contains any additional information concerning the parameter and may occur once or not at all within the ParameterDetails element.

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 26 of 68

119912001201120212031204120512061207120812091210

1211

121212131214121512161217121812191220122112221223

1224122512261227122812291230123112321233123412351236

1237123812391240124112421243124412451246124712481249

7677

78

Page 27: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:complexType name="ParameterDetails">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" /> - <xsd:choice>  <xsd:element name="Units" type="Units" />   <xsd:element name="Unitless" type="Unitless" />   </xsd:choice>  <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="required" />   </xsd:complexType>

2.1.42 PropertyDetails This element declares the content model for PropertyDetails, which contains a description of a property referenced by the PropertyData element. PropertyDetails has one required attribute, id, which may be arbitrarily assigned but must be unique among id attributes assigned elsewhere in a MatML document. PropertyDetails also has one optional attribute, type, for specifying the type of the property (examples include "thermal," "mechanical," "electrical," etc.) PropertyDetails is composed of the following elements. Name contains the name of the property and has one optional attribute, authority, for identifying an authoritative source of property names. Name must occur once and only once within the PropertyDetails element. Units and Unitless are mutually exclusive elements for describing the property's units. Units or Unitless must occur once and only once within the PropertyDetails element. For additional information, see the documentation for the Units and Unitless elements. Notes contains any additional information concerning the property and may occur once or not at all within the PropertyDetails element.

- <xsd:complexType name="PropertyDetails">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" /> - <xsd:choice>  <xsd:element name="Units" type="Units" />   <xsd:element name="Unitless" type="Unitless" />   </xsd:choice>  <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="required" />   <xsd:attribute name="type" type="xsd:string" use="optional" />   </xsd:complexType>

2.1.43 SourceDetails This element declares the content model for SourceDetails, which contains the name of the source of the component. Name contains the name of the source and has one optional attribute,

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 27 of 68

1250125112521253125412551256125712581259126012611262126312641265

1266

12671268126912701271127212731274127512761277127812791280

128112821283128412851286128712881289129012911292129312941295129612971298

1299

130013011302

7980

81

Page 28: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Notes. Notes contains any additional information concerning the data source and may occur once or not at all within the DataSourceDetails element.

- <xsd:complexType name="SourceDetails">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="required" />   <xsd:attribute name="type" type="xsd:string" use="optional" />   </xsd:complexType>

2.1.44 SpecimenDetails This element declares the content model for SpecimenDetails, which contains a description of a specimen referenced by the PropertyData element. SpecimenDetails has one required attribute, id, which may be arbitrarily assigned but must be unique among id attributes assigned elsewhere in a MatML document. SpecimenDetails also has one optional attribute, type, for specifying the type of the specimen (examples include "cylindrical," "rectangular," "full cross-section," "pressed," etc.) SpecimenDetails is composed of the following elements. SpecimenDetails also has 3 optional elements, Name, Geometry, and Notes. Name contains the name of the specimen and has one optional attribute, authority, for identifying an authoritative source of specimen names. Name may occur once or not at all within the SpecimenDetails element. Geometry describes the dimensions of the Component. For additional information, see the documentation for the Geometry type. Geometry may occur once or not at all within the SpecimenDetails element. Notes contains any additional information concerning the specimen and may occur once or not at all within the SpecimenDetails element.

- <xsd:complexType name="SpecimenDetails">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="Name" type="Name" minOccurs="0" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   <xsd:element name="Geometry" type="Geometry" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="required" />   <xsd:attribute name="type" type="xsd:string" use="optional" />   </xsd:complexType>

2.1.45 TestConditionDetails This element declares the content model for TestConditionDetails, which contains a description of the test conditions referenced by the PropertyData element. TestConditionDetails has one required attribute, id, which may be arbitrarily assigned but must be unique among id attributes assigned elsewhere in a MatML document. TestConditionDetails has two optional elements,

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 28 of 68

130313041305

13061307130813091310131113121313131413151316131713181319

132013211322132313241325132613271328132913301331133213331334

13351336133713381339134013411342134313441345134613471348

1349

13501351135213531354

8283

84

Page 29: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

ParameterValue and Notes. ParameterValue contains the value(s) of a parameter, i.e., a test condition, and may occur zero or more times within the TestConditionDetails element. For additional information, see the documentation for the ParameterValue element. Notes contains any additional information concerning the test conditions and may occur once or not at all within the TestConditionDetails element.

- <xsd:complexType name="TestConditionDetails">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:sequence>  <xsd:element name="ParameterValue" type="ParameterValue" minOccurs="0" maxOccurs="unbounded" />   <xsd:element name="Notes" type="Notes" minOccurs="0" />   </xsd:sequence>  <xsd:attribute name="id" type="xsd:ID" use="required" />   </xsd:complexType>

2.1.46 ChemicalElementSymbol This datatype enumerates the valid strings representing chemical elements, which may be used in the Symbol element.

- <!-- Enumerated type definitions follow:  --> - <xsd:simpleType name="ChemicalElementSymbol">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:restriction base="xsd:string">- <xsd:enumeration value="H">- <xsd:annotation>  <xsd:documentation>Hydrogen</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="He">- <xsd:annotation>  <xsd:documentation>Helium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Li">- <xsd:annotation>  <xsd:documentation>Lithium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Be">- <xsd:annotation>  <xsd:documentation>Beryllium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="B">- <xsd:annotation>  <xsd:documentation>Boron</xsd:documentation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 29 of 68

135513561357135813591360

1361136213631364136513661367136813691370137113721373

1374

1375137613771378

13791380

138113821383138413851386138713881389139013911392139313941395139613971398139914001401140214031404140514061407140814091410

8586

87

Page 30: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="C">- <xsd:annotation>  <xsd:documentation>Carbon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="N">- <xsd:annotation>  <xsd:documentation>Nitrogen</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="O">- <xsd:annotation>  <xsd:documentation>Oxygen</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="F">- <xsd:annotation>  <xsd:documentation>Fluorine</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ne">- <xsd:annotation>  <xsd:documentation>Neon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Na">- <xsd:annotation>  <xsd:documentation>Sodium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Mg">- <xsd:annotation>  <xsd:documentation>Magnesium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Al">- <xsd:annotation>  <xsd:documentation>Aluminium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Si">- <xsd:annotation>  <xsd:documentation>Silicon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="P">- <xsd:annotation>  <xsd:documentation>Phosphorus</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="S">- <xsd:annotation>  <xsd:documentation>Sulfur</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Cl">- <xsd:annotation>  <xsd:documentation>Chlorine</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 30 of 68

14111412141314141415141614171418141914201421142214231424142514261427142814291430143114321433143414351436143714381439144014411442144314441445144614471448144914501451145214531454145514561457145814591460146114621463146414651466146714681469147014711472

8889

90

Page 31: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:enumeration value="Ar">- <xsd:annotation>  <xsd:documentation>Argon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="K">- <xsd:annotation>  <xsd:documentation>Potassium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ca">- <xsd:annotation>  <xsd:documentation>Calcium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Sc">- <xsd:annotation>  <xsd:documentation>Scandium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ti">- <xsd:annotation>  <xsd:documentation>Titanium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="V">- <xsd:annotation>  <xsd:documentation>Vanadium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Cr">- <xsd:annotation>  <xsd:documentation>Chromium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Mn">- <xsd:annotation>  <xsd:documentation>Manganese</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Fe">- <xsd:annotation>  <xsd:documentation>Iron</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Co">- <xsd:annotation>  <xsd:documentation>Cobalt</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ni">- <xsd:annotation>  <xsd:documentation>Nickel</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Cu">- <xsd:annotation>  <xsd:documentation>Copper</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Zn">- <xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 31 of 68

14731474147514761477147814791480148114821483148414851486148714881489149014911492149314941495149614971498149915001501150215031504150515061507150815091510151115121513151415151516151715181519152015211522152315241525152615271528152915301531153215331534

9192

93

Page 32: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  <xsd:documentation>Zinc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ga">- <xsd:annotation>  <xsd:documentation>Gallium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ge">- <xsd:annotation>  <xsd:documentation>Germanium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="As">- <xsd:annotation>  <xsd:documentation>Arsenic</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Se">- <xsd:annotation>  <xsd:documentation>Selenium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Br">- <xsd:annotation>  <xsd:documentation>Bromine</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Kr">- <xsd:annotation>  <xsd:documentation>Krypton</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Rb">- <xsd:annotation>  <xsd:documentation>Rubidium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Sr">- <xsd:annotation>  <xsd:documentation>Strontium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Y">- <xsd:annotation>  <xsd:documentation>Yttrium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Zr">- <xsd:annotation>  <xsd:documentation>Zirconium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Nb">- <xsd:annotation>  <xsd:documentation>Niobium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Mo">- <xsd:annotation>  <xsd:documentation>Molybdenum</xsd:documentation>   </xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 32 of 68

15351536153715381539154015411542154315441545154615471548154915501551155215531554155515561557155815591560156115621563156415651566156715681569157015711572157315741575157615771578157915801581158215831584158515861587158815891590159115921593159415951596

9495

96

Page 33: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:enumeration>- <xsd:enumeration value="Tc">- <xsd:annotation>  <xsd:documentation>Technetium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ru">- <xsd:annotation>  <xsd:documentation>Ruthenium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Rh">- <xsd:annotation>  <xsd:documentation>Rhodium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Pd">- <xsd:annotation>  <xsd:documentation>Palladium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ag">- <xsd:annotation>  <xsd:documentation>Silver</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Cd">- <xsd:annotation>  <xsd:documentation>Cadmium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="In">- <xsd:annotation>  <xsd:documentation>Indium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Sn">- <xsd:annotation>  <xsd:documentation>Tin</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Sb">- <xsd:annotation>  <xsd:documentation>Antimony</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Te">- <xsd:annotation>  <xsd:documentation>Tellurium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="I">- <xsd:annotation>  <xsd:documentation>Iodine</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Xe">- <xsd:annotation>  <xsd:documentation>Xenon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Cs">

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 33 of 68

15971598159916001601160216031604160516061607160816091610161116121613161416151616161716181619162016211622162316241625162616271628162916301631163216331634163516361637163816391640164116421643164416451646164716481649165016511652165316541655165616571658

9798

99

Page 34: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:annotation>  <xsd:documentation>Caesium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ba">- <xsd:annotation>  <xsd:documentation>Barium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="La">- <xsd:annotation>  <xsd:documentation>Lanthanum</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ce">- <xsd:annotation>  <xsd:documentation>Cerium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Pr">- <xsd:annotation>  <xsd:documentation>Praseodymium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Nd">- <xsd:annotation>  <xsd:documentation>Neodymium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Pm">- <xsd:annotation>  <xsd:documentation>Promethium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Sm">- <xsd:annotation>  <xsd:documentation>Samarium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Eu">- <xsd:annotation>  <xsd:documentation>Europium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Gd">- <xsd:annotation>  <xsd:documentation>Gadolinium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Tb">- <xsd:annotation>  <xsd:documentation>Terbium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Dy">- <xsd:annotation>  <xsd:documentation>Dysprosium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ho">- <xsd:annotation>  <xsd:documentation>Holmium</xsd:documentation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 34 of 68

16591660166116621663166416651666166716681669167016711672167316741675167616771678167916801681168216831684168516861687168816891690169116921693169416951696169716981699170017011702170317041705170617071708170917101711171217131714171517161717171817191720

100101

102

Page 35: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Er">- <xsd:annotation>  <xsd:documentation>Erbium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Tm">- <xsd:annotation>  <xsd:documentation>Thulium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Yb">- <xsd:annotation>  <xsd:documentation>Ytterbium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Lu">- <xsd:annotation>  <xsd:documentation>Lutetium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Hf">- <xsd:annotation>  <xsd:documentation>Hafnium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ta">- <xsd:annotation>  <xsd:documentation>Tantalum</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="W">- <xsd:annotation>  <xsd:documentation>Tungsten</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Re">- <xsd:annotation>  <xsd:documentation>Rhenium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Os">- <xsd:annotation>  <xsd:documentation>Osmium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ir">- <xsd:annotation>  <xsd:documentation>Iridium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Pt">- <xsd:annotation>  <xsd:documentation>Platinum</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Au">- <xsd:annotation>  <xsd:documentation>Gold</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 35 of 68

17211722172317241725172617271728172917301731173217331734173517361737173817391740174117421743174417451746174717481749175017511752175317541755175617571758175917601761176217631764176517661767176817691770177117721773177417751776177717781779178017811782

103104

105

Page 36: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:enumeration value="Hg">- <xsd:annotation>  <xsd:documentation>Mercury</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Tl">- <xsd:annotation>  <xsd:documentation>Thallium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Pb">- <xsd:annotation>  <xsd:documentation>Lead</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Bi">- <xsd:annotation>  <xsd:documentation>Bismuth</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Po">- <xsd:annotation>  <xsd:documentation>Polonium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="At">- <xsd:annotation>  <xsd:documentation>Astatine</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Rn">- <xsd:annotation>  <xsd:documentation>Radon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Fr">- <xsd:annotation>  <xsd:documentation>Francium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ra">- <xsd:annotation>  <xsd:documentation>Radium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Ac">- <xsd:annotation>  <xsd:documentation>Actinium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Th">- <xsd:annotation>  <xsd:documentation>Thorium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Pa">- <xsd:annotation>  <xsd:documentation>Protactinium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="U">- <xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 36 of 68

17831784178517861787178817891790179117921793179417951796179717981799180018011802180318041805180618071808180918101811181218131814181518161817181818191820182118221823182418251826182718281829183018311832183318341835183618371838183918401841184218431844

106107

108

Page 37: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  <xsd:documentation>Uranium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Np">- <xsd:annotation>  <xsd:documentation>Neptunium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Pu">- <xsd:annotation>  <xsd:documentation>Plutonium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Am">- <xsd:annotation>  <xsd:documentation>Americium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Cm">- <xsd:annotation>  <xsd:documentation>Curium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Bk">- <xsd:annotation>  <xsd:documentation>Berkelium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Cf">- <xsd:annotation>  <xsd:documentation>Californium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Es">- <xsd:annotation>  <xsd:documentation>Einsteinium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Fm">- <xsd:annotation>  <xsd:documentation>Fermium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Md">- <xsd:annotation>  <xsd:documentation>Mendelevium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="No">- <xsd:annotation>  <xsd:documentation>Nobelium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Lr">- <xsd:annotation>  <xsd:documentation>Lawrencium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Rf">- <xsd:annotation>  <xsd:documentation>Rutherfordium</xsd:documentation>   </xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 37 of 68

18451846184718481849185018511852185318541855185618571858185918601861186218631864186518661867186818691870187118721873187418751876187718781879188018811882188318841885188618871888188918901891189218931894189518961897189818991900190119021903190419051906

109110

111

Page 38: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:enumeration>- <xsd:enumeration value="Db">- <xsd:annotation>  <xsd:documentation>Dubnium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Sg">- <xsd:annotation>  <xsd:documentation>Seaborgium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Bh">- <xsd:annotation>  <xsd:documentation>Bohrium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Hs">- <xsd:annotation>  <xsd:documentation>Hassium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Mt">- <xsd:annotation>  <xsd:documentation>Meitnerium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Uun">- <xsd:annotation>  <xsd:documentation>Ununnilium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Uuu">- <xsd:annotation>  <xsd:documentation>Unununium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Uub">- <xsd:annotation>  <xsd:documentation>Ununbium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Uuq">- <xsd:annotation>  <xsd:documentation>Ununquadium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Uuh">- <xsd:annotation>  <xsd:documentation>Ununhexium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="Uuo">- <xsd:annotation>  <xsd:documentation>Ununoctium</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>  </xsd:restriction>  </xsd:simpleType>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 38 of 68

19071908190919101911191219131914191519161917191819191920192119221923192419251926192719281929193019311932193319341935193619371938193919401941194219431944194519461947194819491950195119521953195419551956195719581959196019611962196319641965

19661967

112113

114

Page 39: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

2.1.47 CurrencyCode Based on ISO-4217, and taken from paper N699 on http://www.jtc1sc32.org/ As of 2003-12-11 permission to use this element has been sought from, but not yet been granted by, the authors of the paper. This element declares the content model for value, which contains a string representing a currency. For the most current updates, refer to http://www.din.de/gremien/nas/nabd/iso4217ma/codlistp1/en_listp1.html.

- <xsd:simpleType name="CurrencyCode">- <xsd:annotation>  <xsd:documentation></xsd:documentation>   </xsd:annotation>- <xsd:restriction base="xsd:string">  <xsd:length value="3" /> - <xsd:enumeration value="AFA">- <xsd:annotation>  <xsd:documentation>Afghani</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ALL">- <xsd:annotation>  <xsd:documentation>Lek</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="AMD">- <xsd:annotation>  <xsd:documentation>Armenian Dram</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ANG">- <xsd:annotation>  <xsd:documentation>Netherlands Antillian Guilder</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="AOA">- <xsd:annotation>  <xsd:documentation>Kwanza</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ARS">- <xsd:annotation>  <xsd:documentation>Argentine Peso</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ATS">- <xsd:annotation>  <xsd:documentation>Schilling</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="AUD">- <xsd:annotation>  <xsd:documentation>Australian Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="AWG">- <xsd:annotation>  <xsd:documentation>Aruban Guilder</xsd:documentation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 39 of 68

1968

1969197019711972197319741975

19761977197819791980198119821983198419851986198719881989199019911992199319941995199619971998199920002001200220032004200520062007200820092010201120122013201420152016201720182019202020212022202320242025

115116

117

Page 40: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="AZM">- <xsd:annotation>  <xsd:documentation>Azerbaijanian Manat</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BAM">- <xsd:annotation>  <xsd:documentation>Convertible Marks</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BBD">- <xsd:annotation>  <xsd:documentation>Barbados Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BDT">- <xsd:annotation>  <xsd:documentation>Taka</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BEF">- <xsd:annotation>  <xsd:documentation>Belgian Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BGL">- <xsd:annotation>  <xsd:documentation>Lev</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BGN">- <xsd:annotation>  <xsd:documentation>Bulgarian Lev</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BHD">- <xsd:annotation>  <xsd:documentation>Bahraini Dinar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BIF">- <xsd:annotation>  <xsd:documentation>Burundi Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BMD">- <xsd:annotation>  <xsd:documentation>Bermudian Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BND">- <xsd:annotation>  <xsd:documentation>Brunei Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BOB">- <xsd:annotation>  <xsd:documentation>Boliviano</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 40 of 68

20262027202820292030203120322033203420352036203720382039204020412042204320442045204620472048204920502051205220532054205520562057205820592060206120622063206420652066206720682069207020712072207320742075207620772078207920802081208220832084208520862087

118119

120

Page 41: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:enumeration value="BOV">- <xsd:annotation>  <xsd:documentation>Mvdol</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BRL">- <xsd:annotation>  <xsd:documentation>Brazilian Real</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BSD">- <xsd:annotation>  <xsd:documentation>Bahamian Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BTN">- <xsd:annotation>  <xsd:documentation>Ngultrum</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BWP">- <xsd:annotation>  <xsd:documentation>Pula</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BYB">- <xsd:annotation>  <xsd:documentation>Belarussian Ruble</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BYR">- <xsd:annotation>  <xsd:documentation>Belarussian Ruble</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="BZD">- <xsd:annotation>  <xsd:documentation>Belize Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CAD">- <xsd:annotation>  <xsd:documentation>Canadian Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CDF">- <xsd:annotation>  <xsd:documentation>Franc Congolais</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CHF">- <xsd:annotation>  <xsd:documentation>Swiss Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CLF">- <xsd:annotation>  <xsd:documentation>Unidades de fomento</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CLP">- <xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 41 of 68

20882089209020912092209320942095209620972098209921002101210221032104210521062107210821092110211121122113211421152116211721182119212021212122212321242125212621272128212921302131213221332134213521362137213821392140214121422143214421452146214721482149

121122

123

Page 42: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  <xsd:documentation>Chilean Peso</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CNY">- <xsd:annotation>  <xsd:documentation>Yuan Renminbi</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="COP">- <xsd:annotation>  <xsd:documentation>Colombian Peso</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CRC">- <xsd:annotation>  <xsd:documentation>Costa Rican Colon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CUP">- <xsd:annotation>  <xsd:documentation>Cuban Peso</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CVE">- <xsd:annotation>  <xsd:documentation>Cape Verde Escudo</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CYP">- <xsd:annotation>  <xsd:documentation>Cyprus Pound</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="CZK">- <xsd:annotation>  <xsd:documentation>Czech Koruna</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="DEM">- <xsd:annotation>  <xsd:documentation>Deutsche Mark</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="DJF">- <xsd:annotation>  <xsd:documentation>Djibouti Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="DKK">- <xsd:annotation>  <xsd:documentation>Danish Krone</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="DOP">- <xsd:annotation>  <xsd:documentation>Dominican Peso</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="DZD">- <xsd:annotation>  <xsd:documentation>Algerian Dinar</xsd:documentation>   </xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 42 of 68

21502151215221532154215521562157215821592160216121622163216421652166216721682169217021712172217321742175217621772178217921802181218221832184218521862187218821892190219121922193219421952196219721982199220022012202220322042205220622072208220922102211

124125

126

Page 43: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:enumeration>- <xsd:enumeration value="EEK">- <xsd:annotation>  <xsd:documentation>Kroon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="EGP">- <xsd:annotation>  <xsd:documentation>Egyptian Pound</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ERN">- <xsd:annotation>  <xsd:documentation>Nakfa</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ESP">- <xsd:annotation>  <xsd:documentation>Spanish Peseta</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ETB">- <xsd:annotation>  <xsd:documentation>Ethiopian Birr</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="EUR">- <xsd:annotation>  <xsd:documentation>Euro</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="FIM">- <xsd:annotation>  <xsd:documentation>Markka</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="FJD">- <xsd:annotation>  <xsd:documentation>Fiji Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="FKP">- <xsd:annotation>  <xsd:documentation>Falkland Islands Pound</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="FRF">- <xsd:annotation>  <xsd:documentation>French Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GBP">- <xsd:annotation>  <xsd:documentation>Pound Sterling</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GEL">- <xsd:annotation>  <xsd:documentation>Lari</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GHC">

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 43 of 68

22122213221422152216221722182219222022212222222322242225222622272228222922302231223222332234223522362237223822392240224122422243224422452246224722482249225022512252225322542255225622572258225922602261226222632264226522662267226822692270227122722273

127128

129

Page 44: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:annotation>  <xsd:documentation>Cedi</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GIP">- <xsd:annotation>  <xsd:documentation>Gibraltar Pound</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GMD">- <xsd:annotation>  <xsd:documentation>Dalasi</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GNF">- <xsd:annotation>  <xsd:documentation>Guinea Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GRD">- <xsd:annotation>  <xsd:documentation>Drachma</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GTQ">- <xsd:annotation>  <xsd:documentation>Quetzal</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GWP">- <xsd:annotation>  <xsd:documentation>Guinea-Bissau Peso</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="GYD">- <xsd:annotation>  <xsd:documentation>Guyana Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="HKD">- <xsd:annotation>  <xsd:documentation>Hong Kong Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="HNL">- <xsd:annotation>  <xsd:documentation>Lempira</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="HRK">- <xsd:annotation>  <xsd:documentation>Croatian kuna</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="HTG">- <xsd:annotation>  <xsd:documentation>Gourde</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="HUF">- <xsd:annotation>  <xsd:documentation>Forint</xsd:documentation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 44 of 68

22742275227622772278227922802281228222832284228522862287228822892290229122922293229422952296229722982299230023012302230323042305230623072308230923102311231223132314231523162317231823192320232123222323232423252326232723282329233023312332233323342335

130131

132

Page 45: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="IDR">- <xsd:annotation>  <xsd:documentation>Rupiah</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="IEP">- <xsd:annotation>  <xsd:documentation>Irish Pound</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ILS">- <xsd:annotation>  <xsd:documentation>New Israeli Sheqel</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="INR">- <xsd:annotation>  <xsd:documentation>Indian Rupee</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="IQD">- <xsd:annotation>  <xsd:documentation>Iraqi Dinar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="IRR">- <xsd:annotation>  <xsd:documentation>Iranian Rial</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ISK">- <xsd:annotation>  <xsd:documentation>Iceland Krona</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ITL">- <xsd:annotation>  <xsd:documentation>Italian Lira</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="JMD">- <xsd:annotation>  <xsd:documentation>Jamaican Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="JOD">- <xsd:annotation>  <xsd:documentation>Jordanian Dinar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="JPY">- <xsd:annotation>  <xsd:documentation>Yen</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="KES">- <xsd:annotation>  <xsd:documentation>Kenyan Shilling</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 45 of 68

23362337233823392340234123422343234423452346234723482349235023512352235323542355235623572358235923602361236223632364236523662367236823692370237123722373237423752376237723782379238023812382238323842385238623872388238923902391239223932394239523962397

133134

135

Page 46: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:enumeration value="KGS">- <xsd:annotation>  <xsd:documentation>Som</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="KHR">- <xsd:annotation>  <xsd:documentation>Riel</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="KMF">- <xsd:annotation>  <xsd:documentation>Comoro Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="KPW">- <xsd:annotation>  <xsd:documentation>North Korean Won</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="KRW">- <xsd:annotation>  <xsd:documentation>Won</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="KWD">- <xsd:annotation>  <xsd:documentation>Kuwaiti Dinar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="KYD">- <xsd:annotation>  <xsd:documentation>Cayman Islands Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="KZT">- <xsd:annotation>  <xsd:documentation>Tenge</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LAK">- <xsd:annotation>  <xsd:documentation>Kip</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LBP">- <xsd:annotation>  <xsd:documentation>Lebanese Pound</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LKR">- <xsd:annotation>  <xsd:documentation>Sri Lanka Rupee</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LRD">- <xsd:annotation>  <xsd:documentation>Liberian Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LSL">- <xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 46 of 68

23982399240024012402240324042405240624072408240924102411241224132414241524162417241824192420242124222423242424252426242724282429243024312432243324342435243624372438243924402441244224432444244524462447244824492450245124522453245424552456245724582459

136137

138

Page 47: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  <xsd:documentation>Loti</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LTL">- <xsd:annotation>  <xsd:documentation>Lithuanian Litus</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LUF">- <xsd:annotation>  <xsd:documentation>Luxembourg Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LVL">- <xsd:annotation>  <xsd:documentation>Latvian Lats</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="LYD">- <xsd:annotation>  <xsd:documentation>Libyan Dinar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MAD">- <xsd:annotation>  <xsd:documentation>Moroccan Dirham</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MDL">- <xsd:annotation>  <xsd:documentation>Moldovan Leu</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MGF">- <xsd:annotation>  <xsd:documentation>Malagasy Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MKD">- <xsd:annotation>  <xsd:documentation>Denar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MMK">- <xsd:annotation>  <xsd:documentation>Kyat</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MNT">- <xsd:annotation>  <xsd:documentation>Tugrik</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MOP">- <xsd:annotation>  <xsd:documentation>Pataca</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MRO">- <xsd:annotation>  <xsd:documentation>Ouguiya</xsd:documentation>   </xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 47 of 68

24602461246224632464246524662467246824692470247124722473247424752476247724782479248024812482248324842485248624872488248924902491249224932494249524962497249824992500250125022503250425052506250725082509251025112512251325142515251625172518251925202521

139140

141

Page 48: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:enumeration>- <xsd:enumeration value="MTL">- <xsd:annotation>  <xsd:documentation>Maltese Lira</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MUR">- <xsd:annotation>  <xsd:documentation>Mauritius Rupee</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MVR">- <xsd:annotation>  <xsd:documentation>Rufiyaa</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MWK">- <xsd:annotation>  <xsd:documentation>Kwacha</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MXN">- <xsd:annotation>  <xsd:documentation>Mexican Peso</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MXV">- <xsd:annotation>  <xsd:documentation>Mexican Unidad de Inversion (UDI)</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MYR">- <xsd:annotation>  <xsd:documentation>Malaysian Ringgit</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="MZM">- <xsd:annotation>  <xsd:documentation>Metical</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="NAD">- <xsd:annotation>  <xsd:documentation>Namibia Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="NGN">- <xsd:annotation>  <xsd:documentation>Naira</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="NIO">- <xsd:annotation>  <xsd:documentation>Cordoba Oro</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="NLG">- <xsd:annotation>  <xsd:documentation>Netherlands Guilder</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 48 of 68

25222523252425252526252725282529253025312532253325342535253625372538253925402541254225432544254525462547254825492550255125522553255425552556255725582559256025612562256325642565256625672568256925702571257225732574257525762577257825792580258125822583

142143

144

Page 49: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:enumeration value="NOK">- <xsd:annotation>  <xsd:documentation>Norwegian Krone</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="NPR">- <xsd:annotation>  <xsd:documentation>Nepalese Rupee</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="NZD">- <xsd:annotation>  <xsd:documentation>New Zealand Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="OMR">- <xsd:annotation>  <xsd:documentation>Rial Omani</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="PAB">- <xsd:annotation>  <xsd:documentation>Balboa</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="PEN">- <xsd:annotation>  <xsd:documentation>Nuevo Sol</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="PGK">- <xsd:annotation>  <xsd:documentation>Kina</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="PHP">- <xsd:annotation>  <xsd:documentation>Philippine Peso</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="PKR">- <xsd:annotation>  <xsd:documentation>Pakistan Rupee</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="PLN">- <xsd:annotation>  <xsd:documentation>Zloty</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="PTE">- <xsd:annotation>  <xsd:documentation>Portuguese Escudo</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="PYG">- <xsd:annotation>  <xsd:documentation>Guarani</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="QAR">- <xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 49 of 68

25842585258625872588258925902591259225932594259525962597259825992600260126022603260426052606260726082609261026112612261326142615261626172618261926202621262226232624262526262627262826292630263126322633263426352636263726382639264026412642264326442645

145146

147

Page 50: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  <xsd:documentation>Qatari Rial</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ROL">- <xsd:annotation>  <xsd:documentation>Leu</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="RUB">- <xsd:annotation>  <xsd:documentation>Russian Ruble</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="RUR">- <xsd:annotation>  <xsd:documentation>Russian Ruble</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="RWF">- <xsd:annotation>  <xsd:documentation>Rwanda Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SAR">- <xsd:annotation>  <xsd:documentation>Saudi Riyal</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SBD">- <xsd:annotation>  <xsd:documentation>Solomon Islands Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SCR">- <xsd:annotation>  <xsd:documentation>Seychelles Rupee</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SDD">- <xsd:annotation>  <xsd:documentation>Sudanese Dinar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SEK">- <xsd:annotation>  <xsd:documentation>Swedish Krona</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SGD">- <xsd:annotation>  <xsd:documentation>Singapore Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SHP">- <xsd:annotation>  <xsd:documentation>Saint Helena Pound</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SIT">- <xsd:annotation>  <xsd:documentation>Tolar</xsd:documentation>   </xsd:annotation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 50 of 68

26462647264826492650265126522653265426552656265726582659266026612662266326642665266626672668266926702671267226732674267526762677267826792680268126822683268426852686268726882689269026912692269326942695269626972698269927002701270227032704270527062707

148149

150

Page 51: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:enumeration>- <xsd:enumeration value="SKK">- <xsd:annotation>  <xsd:documentation>Slovak Koruna</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SLL">- <xsd:annotation>  <xsd:documentation>Leone</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SOS">- <xsd:annotation>  <xsd:documentation>Somali Shilling</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SRG">- <xsd:annotation>  <xsd:documentation>Suriname Guilder</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="STD">- <xsd:annotation>  <xsd:documentation>Dobra</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SVC">- <xsd:annotation>  <xsd:documentation>El Salvador Colon</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SYP">- <xsd:annotation>  <xsd:documentation>Syrian Pound</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="SZL">- <xsd:annotation>  <xsd:documentation>Lilangeni</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="THB">- <xsd:annotation>  <xsd:documentation>Baht</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TJR">- <xsd:annotation>  <xsd:documentation>Tajik Ruble</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TMM">- <xsd:annotation>  <xsd:documentation>Manat</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TND">- <xsd:annotation>  <xsd:documentation>Tunisian Dinar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TOP">

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 51 of 68

27082709271027112712271327142715271627172718271927202721272227232724272527262727272827292730273127322733273427352736273727382739274027412742274327442745274627472748274927502751275227532754275527562757275827592760276127622763276427652766276727682769

151152

153

Page 52: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

- <xsd:annotation>  <xsd:documentation>Pa’anga</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TPE">- <xsd:annotation>  <xsd:documentation>Timor Escudo</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TRL">- <xsd:annotation>  <xsd:documentation>Turkish Lira</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TTD">- <xsd:annotation>  <xsd:documentation>Trinidad and Tobago Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TWD">- <xsd:annotation>  <xsd:documentation>New Taiwan Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="TZS">- <xsd:annotation>  <xsd:documentation>Tanzanian Shilling</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="UAH">- <xsd:annotation>  <xsd:documentation>Hryvnia</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="UGX">- <xsd:annotation>  <xsd:documentation>Uganda Shilling</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="USD">- <xsd:annotation>  <xsd:documentation>US Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="UYU">- <xsd:annotation>  <xsd:documentation>Peso Uruguayo</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="UZS">- <xsd:annotation>  <xsd:documentation>Uzbekistan Sum</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="VEB">- <xsd:annotation>  <xsd:documentation>Bolivar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="VND">- <xsd:annotation>  <xsd:documentation>Dong</xsd:documentation>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 52 of 68

27702771277227732774277527762777277827792780278127822783278427852786278727882789279027912792279327942795279627972798279928002801280228032804280528062807280828092810281128122813281428152816281728182819282028212822282328242825282628272828282928302831

154155

156

Page 53: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="VUV">- <xsd:annotation>  <xsd:documentation>Vatu</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="WST">- <xsd:annotation>  <xsd:documentation>Tala</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="XAF">- <xsd:annotation>  <xsd:documentation>CFA Franc BEAC</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="XCD">- <xsd:annotation>  <xsd:documentation>East Caribbean Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="XDR">- <xsd:annotation>  <xsd:documentation>SDR</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="XOF">- <xsd:annotation>  <xsd:documentation>CFA Franc BCEAO</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="XPF">- <xsd:annotation>  <xsd:documentation>CFP Franc</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="YER">- <xsd:annotation>  <xsd:documentation>Yemeni Rial</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="YUM">- <xsd:annotation>  <xsd:documentation>Yugoslavian Dinar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ZAR">- <xsd:annotation>  <xsd:documentation>Rand</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ZMK">- <xsd:annotation>  <xsd:documentation>Kwacha</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>- <xsd:enumeration value="ZWD">- <xsd:annotation>  <xsd:documentation>Zimbabwe Dollar</xsd:documentation>   </xsd:annotation>  </xsd:enumeration>

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 53 of 68

28322833283428352836283728382839284028412842284328442845284628472848284928502851285228532854285528562857285828592860286128622863286428652866286728682869287028712872287328742875287628772878287928802881288228832884288528862887288828892890289128922893

157158

159

Page 54: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

  </xsd:restriction>  </xsd:simpleType>  </xsd:schema>

2.2 Character StylesThis template defines several character styles for general text use: Element style (shortcut Ctrl-Shift-E) for <NativeElement> names and

<ns:ForeignElement> names; add the angle brackets yourself

Attribute style (shortcut Ctrl-Shift-A) for attributeNames

Datatype style (shortcut Ctrl-Shift-Alt-D) for DataType names

Keyword style (shortcut Ctrl-Shift-K) for OtherKeyword names

Variable style (shortcut Ctrl-Shift-Alt-V) for variable names

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 54 of 68

289428952896

2897

28982899290029012902290329042905

160161

162

Page 55: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

3 References3.1 Normative

[RFC2119] S. Bradner, Key words for use in RFCs to Indicate Requirement Levels, http://www.ietf.org/rfc/rfc2119.txt, IETF RFC 2119, March 1997.

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 55 of 68

2906

290729082909

163164

165

Page 56: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Appendix A. AcknowledgmentsThe OASIS Materials Markup Language Technical Committee acknowledges members of the committee during the development of this specification and those who have contributed through the MatML Coordination Committee:

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 56 of 68

2910

291129122913

166167

168

Page 57: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Appendix B. Revision HistoryRev Date By Whom What

wd-00 2005-09-15 B. Johanson Draft

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 57 of 68

2914

2915

169170

171

Page 58: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Appendix C. NoticesOASIS takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on OASIS's procedures with respect to rights in OASIS specifications can be found at the OASIS website. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification, can be obtained from the OASIS Executive Director.OASIS invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to implement this specification. Please address the information to the OASIS Executive Director.Copyright © OASIS Open 2002. All Rights Reserved.This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself does not be modified in any way, such as by removing the copyright notice or references to OASIS, except as needed for the purpose of developing OASIS specifications, in which case the procedures for copyrights defined in the OASIS Intellectual Property Rights document must be followed, or as required to translate it into languages other than English.The limited permissions granted above are perpetual and will not be revoked by OASIS or its successors or assigns.This document and the information contained herein is provided on an “AS IS” basis and OASIS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 58 of 68

2916

291729182919292029212922292329242925292629272928292929302931293229332934293529362937293829392940294129422943294429452946

172173

174

Page 59: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Appendix D. Terminology Specifications and Materials Nomenclature

Table 1. List of recommended specifications and standards for terminology and naming conventions of materials related information.

Source

Doc Number

Pub Date Title

ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners

ASME SEC II A SA-751

7/1/2004 SA-751 Specification for Test Methods, Practices, and terminology for Chemical Analysis of Steel Products-ASTM A 751-01

ASME SEC II A SA-941

7/1/2004 SA-941 Specification for terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys-ASTM A941-99B

ASTM A 340 REV A

6/10/2003 Standard terminology of Symbols and Definitions Relating to Magnetic Testing

ASTM A 644 12/10/1998 Standard terminology Relating to Iron Castings

ASTM A 902 4/1/2005 Standard terminology Relating to Metallic Coated Steel Products

ASTM A 941 REV A

7/1/2004 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

ASTM B 243 REV A

3/31/2005 Standard terminology of Powder Metallurgy

ASTM B 354 3/1/2005 Standard terminology Relating to Uninsulated Metallic Electrical Conductors

ASTM B 374 5/10/1996 Standard terminology Relating to Electroplating

ASTM B 542 5/1/2004 Standard terminology Relating to Electrical Contacts and Their Use

ASTM B 846 5/10/2001 Standard terminology for Copper and Copper Alloys

ASTM B 881 REV A

1/10/1998 Standard terminology Relating to Aluminum- and Magnesium-Alloy Products

ASTM B 899 5/1/2004 Standard terminology Relating to Non-Ferrous Metals and Alloys

ASTM C 11 5/1/2005 Standard terminology Relating to Gypsum and Related Building Materials and Systems

ASTM C 43 2/1/2005 Standard terminology of Structural Clay Products

ASTM C 51 2/1/2005 Standard terminology Relating to Lime and Limestone (as Used by the Industry)

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 59 of 68

2947

2948

29492950

175176

177

Page 60: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

ASTM C 71 REV A

12/10/2001 Standard terminology Relating to Refractories

ASTM C 125 6/10/2003 Standard terminology Relating to Concrete and Concrete Aggregates

ASTM C 162 6/1/2004 Standard terminology of Glass and Glass Products

ASTM C 168 6/1/2005 Standard terminology Relating to Thermal Insulation

ASTM C 219 2/10/2003 Standard terminology Relating to Hydraulic Cement

ASTM C 242 7/10/2001 Standard terminology of Ceramic Whitewares and Related Products

ASTM C 274 10/10/1999 Standard terminology of Structural Sandwich Constructions

ASTM C 286 10/10/1999 Standard terminology Relating to Porcelain Enamel and Ceramic-Metal Systems

ASTM C 709 REV A

11/1/2003 Standard terminology Relating to Manufactured Carbon and Graphite

ASTM C 717 REV A

7/1/2005 Standard terminology of Building Seals and Sealants

ASTM C 822 REV A

5/15/2005 Standard terminology Relating to Concrete Pipe and Related Products

ASTM C 896 11/1/2004 Standard terminology Relating to Clay Products

ASTM C 904 5/10/2001 Standard terminology Relating to Chemical-Resistant Nonmetallic Materials

ASTM C 1145 1/1/2005 Standard terminology of Advanced Ceramics

ASTM C 1154 11/10/2002 Standard terminology for Non-Asbestos Fiber-Reinforced Cement Products

ASTM C 1180 REV A

9/10/2003 Standard terminology of Mortar and Grout for Unit Masonry

ASTM C 1209 2/1/2005 Standard terminology of Concrete Masonry Units and Related Units

ASTM C 1232 1/1/2005 Standard terminology of Masonry

ASTM D 8 7/10/2002 Standard terminology Relating to Materials for Roads and Pavements

ASTM D 9 3/9/1987 Standard terminology Relating to Wood

ASTM D 16 7/10/2003 Standard terminology for Paint, Related Coatings, Materials, and Applications

ASTM D 121 5/1/2005 Standard terminology of Coal and Coke

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 60 of 68

178179

180

Page 61: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

ASTM D 123 2/10/2003 Standard terminology Relating to Textiles

ASTM D 653 7/1/2005 Standard terminology Relating to Soil, Rock, and Contained Fluids

ASTM D 883 8/10/2000 Standard terminology Relating to Plastics

ASTM D 907 4/1/2005 Standard terminology of Adhesives

ASTM D 996 4/1/2004 Standard terminology of Packaging and Distribution Environments

ASTM D 1038 2/25/1983 Standard terminology Relating to Veneer and Plywood

ASTM D 1554 2/10/2001 Standard terminology Relating to Wood-Base Fiber and Particle Panel Materials

ASTM D 1566 REV A

3/1/2005 Standard terminology Relating to Rubber

ASTM D 1600 11/10/1999 Standard terminology for Abbreviated Terms Relating to Plastics

ASTM D 1711 3/10/2002 Standard terminology Relating to Electrical Insulation

ASTM D 1968 REV A

10/10/2002 Standard terminology Relating to Paper and Paper Products

ASTM D 2050 10/1/2004 Standard terminology Relating to Subassemblies

ASTM D 2652 REV A

7/1/2005 Standard terminology Relating to Activated Carbon

ASTM D 2825 9/10/2002 Standard terminology Relating to Polishes and Related Materials

ASTM D 2864 6/10/2002 Standard terminology Relating to Electrical Insulating Liquids and Gases

ASTM D 2946 1/10/2001 Standard terminology for Asbestos and Asbestos-Cement Products

ASTM D 3053 REV B

11/1/2004 Standard terminology Relating to Carbon Black

ASTM D 3853 1/10/2003 Standard terminology Relating to Rubber and Rubber LaticesAbbreviations for Chemicals Used in Compounding

ASTM D 3878 REV A

5/1/2004 Standard terminology for Composite Materials

ASTM D 3918 11/10/1996 Standard terminology Relating to Reinforced Plastic Pultruded Products

ASTM D 3990 9/10/1999 Standard terminology Relating to Fabric Defects

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 61 of 68

181182

183

Page 62: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

ASTM D 4092 9/10/2001 Standard terminology Plastics: Dynamic Mechanical Properties

ASTM D 4127 1/10/2002 Standard terminology Used with Ion-Selective Electrodes

ASTM D 4150 8/10/2003 Standard terminology Relating to Gaseous Fuels

ASTM D 4175 REV A

8/10/2002 Standard terminology Relating to Petroleum, Petroleum Products, and Lubricants

ASTM D 4391 REV A

11/15/1993 Standard terminology Relating to the Burning Behavior of Textiles

ASTM D 4439 6/1/2004 Standard terminology for Geosynthetics

ASTM D 4466 1/10/2002 Standard terminology for Multicomponent Textile Fibers

ASTM D 4538 1/15/1995 Standard terminology Relating to Protective Coating and Lining Work for Power Generation Facilities

ASTM D 4725 5/1/2004 Standard terminology for Engine Coolants

ASTM D 4790 6/10/1999 Standard terminology of Aromatic Hydrocarbons and Related Chemicals

ASTM D 5077 6/29/1990 Standard terminology Relating to Electrostatic Discharge (ESD) Packaging Materials

ASTM D 5535 2/10/1998 Standard terminology Relating to Formed-In-Place Sealants for Joints and Cracks in Pavements

ASTM D 6161 6/1/2005 Standard terminology Used for Microfiltration, Ultrafiltration, Nanofiltration and Reverse Osmosis Membrane Processes

ASTM D 6384 REV A

5/10/1999 Standard terminology Relating to Biodegradability and Ecotoxicity of Lubricants

ASTM D 6440 12/10/2001 Standard terminology Relating to Hydrocarbon Resins

ASTM D 7188 7/1/2005 Standard terminology for Printing Inks, Materials, and Processes

ASTM E 6 6/10/2003 Standard terminology Relating to Methods of Mechanical Testing

ASTM E 7 5/10/2003 Standard terminology Relating to Metallography

ASTM E 41 5/15/1992 Standard terminology Relating to Conditioning

ASTM E 131 9/10/2002 Standard terminology Relating to Molecular Spectroscopy

ASTM E 135 7/25/2005 Standard terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 62 of 68

184185

186

Page 63: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

ASTM E 170 1/1/2005 Standard terminology Relating to Radiation Measurements and Dosimetry

ASTM E 175 1/1/1982 Standard terminology of Microscopy

ASTM E 176 REV A

7/1/2005 Standard terminology of Fire Standards

ASTM E 253 8/1/2005 Standard terminology Relating to Sensory Evaluation of Materials and Products

ASTM E 456 10/10/2002 Standard terminology Relating to Quality and Statistics

ASTM E 473 10/1/2004 Standard terminology Relating to Thermal Analysis and Rheology

ASTM E 631 REV A

8/15/1993 Standard terminology of Building Constructions

ASTM E 673 12/1/2003 Standard terminology Relating to Surface Analysis

ASTM E 1102 5/15/1991 Standard terminology Relating to Agricultural Chemical Application

ASTM E 1142 12/1/2004 Standard terminology Relating to Thermophysical Properties

ASTM E 1316 3/1/2005 Standard terminology for Nondestructive Testing

ASTM E 1325 10/10/2002 Standard terminology Relating to Design of Experiments

ASTM E 1402 11/10/1999 Standard terminology Relating to Sampling

ASTM E 1445 7/10/2003 Standard terminology Relating to Hazardous Potential of Chemicals

ASTM E 1481 REV A

4/10/2000 Standard terminology of Railing Systems and Rails for Buildings

ASTM E 1547 9/10/1999 Standard terminology Relating to Industrial and Specialty Chemicals

ASTM E 1605 11/1/2004 Standard terminology Relating to Lead in Buildings

ASTM E 1638 11/15/1994 Standard terminology Relating to Sieve Analysis

ASTM E 1658 10/1/2004 Standard terminology for Expressing Conclusions of Forensic Document Examiners

ASTM E 1705 4/15/1995 Standard terminology Relating to Biotechnology

ASTM E 1732 REV A

5/10/1996 Standard terminology Relating to Forensic Science

ASTM E 1823 5/1/2005 Standard terminology Relating to Fatigue and Fracture Testing

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 63 of 68

187188

189

Page 64: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

ASTM E 1964 7/10/1998 Standard Practice for Compiling and Writing & terminology

ASTM E 1992 REV B

9/10/1999 Standard terminology Relating to terminology Management

ASTM E 2444 5/1/2005 terminology Relating to Measurements Taken on Thin, Reflecting Films

ASTM F 17 10/10/2002 Standard terminology Relating to Flexible Barrier Materials

ASTM F 149 REV B

12/15/1992 Standard terminology Relating to Optical Character Recognition

ASTM F 221 12/10/1998 Standard terminology Relating to Carbon Paper and Inked Ribbon Products and Images Made Therefrom

ASTM F 1251 11/24/1989 Standard terminology Relating to Polymeric Biomaterials in Medical and Surgical Devices

ASTM F 1327 4/1/2005 Standard terminology Relating to Barrier Materials for Medical Packaging

ASTM F 2005 1/10/2000 Standard terminology for Nickel-Titanium Shape Memory Alloys

ASTM F 2078 5/10/2001 Standard terminology Relating to Hydrogen Embrittlement Testing

ASTM F 2488 7/1/2005 Standard terminology for Rolling Element Bearings

ASTM G 15 6/15/2005 Standard terminology Relating to Corrosion and Corrosion Testing

ASTM G 40 5/1/2005 Standard terminology Relating to Wear and Erosion

ASTM E 1338 10/7/1997 Standard Guide for the Identification of Metals and Alloys in Computerized Material Property Databases-Replaces E1339-90

ASTM E 1761 10/11/1995 Standard Guide for Recommended Formats for Data Records Used in Computerization of Fatigue and Fracture Data of Metals

AWS CM CH 5 1/1/2000 Weld Geometry and Welding terminology

AWS WJT-G 1/1/1995 Joint - Weld terminology and Standard Welding Symbols Interpretation

BSI BS 2737 1/1/1956 Terminology of Internal Defects in Castings as Revealed by Radiography

BSI BS 7238 1/1/1990 Glossary for terminology Related to Microprocessors

BSI BS 7776 1/1/1995 Glossary of Torque terminology for Threaded Fasteners (E)

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 64 of 68

190191

192

Page 65: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

BSI BS 7848 2/15/1996 Gears - Wear and Damage to Gear Teeth - terminology

BSI BS EN 303-1

8/15/1999 Heating Boilers - Part 1: Heating Boilers with Forced Draught Burners - terminology, General Requirements, Testing and Marking-Supersedes BS 4256-2: 1972;

BSI BS EN 303-4

8/15/1999 Heating Boilers - Part 4: Heating Boilers with Forced Draught Burners - Special Requirements for Boilers with Forced Draught Oil Burners with Outputs up to 70 kW and a Maximum Operating Pressure of 3 Bar - terminology, Special Requirements, Testing and Marking-Partially Supersedes BS 779:1989, and BS 855:1990;

BSI BS EN 303-5

11/15/1999 Heating Boilers - Part 5: Heating Boilers for Solid Fuels, Hand and Automatically Fired, Nominal Heat Output of up to 300 kW - terminology, Requirements, Testing and Marking

BSI BS EN 657 1/1/1994 Thermal Spraying - terminology, Classification

BSI BS EN 764-1

6/14/2004 Pressure equipment Part 1: terminology Pressure, temperature, volume, nominal size-Supersedes BS EN 764:1995

BSI BS EN 932-3

1/15/1997 Tests for general properties of aggregates Part 3: Procedure and terminology for simplified petrographic description-AMD 14865: February 26, 2004

BSI BS EN 1094-1

8/15/1997 Insulating Refractory Products Part 1: terminology for Ceramic Fibre Products

BSI BS EN 1330-1

12/15/1998 Non-Destructive Testing - terminology - Part 1: List of General Terms

BSI BS EN 1330-2

12/15/1998 Non-Destructive Testing - terminology - Part 2: Terms Common to the Non-Destructive Testing Methods

BSI BS EN 1330-3

9/15/1997 Non-Destructive Testing - terminology Part 3: Terms Used in Industrial Radiographic Testing-Supersedes BS 3683: Part 3: 1984;

BSI BS EN 1330-4

4/15/2000 Non-Destructive Testing - terminology - Part 4: Terms Used in Ultrasonic Testing-Supersedes BS 3683-4:1985;

BSI BS EN 1330-5

11/15/1998 Non-Destructive Testing - terminology - Part 5: Terms Used in Eddy Current Testing-Supersedes BS 3683-5: 1965;

BSI BS EN 1330-7

2/4/2005 Non-destructive testing terminology Part 7: Terms used in magnetic particle testing-Supersedes BS 3683-2:1985

BSI BS EN 1330-8

8/15/1998 Non-Destructive Testing - terminology - Part 8: Terms Used in Leak Tightness Testing

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 65 of 68

193194

195

Page 66: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

BSI BS EN 1330-9

4/15/2000 Non-Destructive Testing - terminology - Part 9: Terms Used in Acoustic Emission Testing

BSI BS EN 1330-10

3/12/2003 Non-destructive testing - terminology - Part 10: Terms used in visual testing

BSI BS EN 1556

12/15/1998 Bar Coding - terminology

BSI BS EN 12670

2/27/2002 Natural Stone - terminology

BSI BS EN 13193

9/15/2000 Packaging - Packaging and the Enviroment - terminology

BSI BS EN 13360

12/19/2002 Rubber- or plastics-coated fabrics terminology

BSI BS EN 13622

6/10/2002 Gas Welding Equipment - terminology - Terms Used for Gas Welding Equipment-Partially Supersedes BS 499-1:1991;

BSI BS EN 13857-1

7/25/2003 Explosives for civil uses Part 1: terminology

BSI BS EN 14035-1

8/8/2003 Fireworks Part 1: terminology-Together with BS EN 14035-2:2003,it supersedes BS 7114-1:1988;

BSI BS EN 14182

12/12/2002 Packaging terminology Basic terms and definitions

BSI BS EN 14564

10/29/2004 Tanks for transport of dangerous goods terminology

BSI BS EN 14618

4/18/2005 Agglomerated stone terminology and classification

BSI BS EN 61512-1

10/15/1999 Batch Control - Part 1: Models and terminology-IEC 61512-1:1997;

BSI BS EN ISO 12706

1/15/2001 Non-Destructive Testing - terminology - Terms Used in Penetrant Testing-Supersedes BS 3683-1:1985;

BSI BS EN ISO 14588

3/15/2001 Blind rivets terminology and definitions-AMD 15340:November 22, 2004; Together with BS EN ISO 14589:2001, BS EN ISO 15973:2000, BS EN ISO 15974:2001, BS EN ISO 15975:2002, BS EN ISO 15976:2002, BS EN ISO 15977:2002, BS EN ISO 15978:2002 and BS EN ISO 15979:2002 supersedes BS 7349-1:1993

BSI BS EN ISO 15367-1

10/22/2003 Lasers and laser-related equipment Test methods for determination of the shape of a laser beam wavefront Part 1: terminology and fundamental aspects-CORR 14872: November 24, 2003;

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 66 of 68

196197

198

Page 67: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

BSI BS ISO 1087-1

9/26/2002 Terminology work Vocabulary Part 1: Theory and application

BSI BS ISO 1087-2

6/15/2000 Terminology Work - Vocabulary - Part 2: Computer Applications

BSI BS ISO 1998-1

1/1/1998 Petroleum Industry - terminology - Part 1: Raw Materials and Products-CORR 10792; April 2001;

BSI BS ISO 1998-2

1/1/1998 Petroleum Industry - terminology - Part 2: Properties and Tests

BSI BS ISO 1998-3

1/1/1998 Petroleum Industry - terminology - Part 3: Exploration and Production

BSI BS ISO 1998-4

1/1/1998 Petroleum Industry - terminology - Part 4: Refining

BSI BS ISO 1998-5

1/1/1998 Petroleum Industry - terminology - Part 5: Transport, Storage, Distribution-CORR 10793: February 2001;

BSI BS ISO 1998-6

10/15/2000 Petroleum Industry - terminology - Part 6: Measurement

BSI BS ISO 1998-7

1/1/1998 Petroleum Industry - terminology - Part 7: Miscellaneous Terms

BSI BS ISO 1998-99

10/15/2000 Petroleum Industry - terminology - Part 99: General and Index

BSI BS ISO 4046-2

1/1/2002 Paper, board, pulps and related terms Vocabulary Part 2: Pulping terminology-Together with BS ISO 4046-1, BS ISO 4046-3, BS ISO 4046-4 and BS ISO 4046-5, it supersedes BS 3203:1979;

BSI BS ISO 4046-3

1/1/2002 Paper, board, pulps and related terms Vocabulary Part 3: Paper-making terminology-Together with BS ISO 4046-1, BS ISO 4046-2, BS ISO 4046-4 and BS ISO 4046-5, it supersedes BS 3203:1979;

BSI BS ISO 11090-1

5/15/1998 Machine Tools - Test Conditions for Die Sinking Electro-Discharge Machines (EDM) - terminology and Testing of Accuracy - Part 1: Single Column Machines (Cross Slide Table Type and Fixed Table Type)

BSI BS ISO 11090-2

12/15/1998 Machine Tools - Test Conditions for Die Sinking Electro-Discharge Machines (EDM) - terminology and Testing of Accuracy - Part 2: Two Column Machines (Slide-Head Type and Cross-Slide Table Type)

BSI BS ISO 12620

1/1/1999 Computer applications in terminology Data categories

BSI BS ISO 12637-5

9/15/2001 Graphic Technology - Multilingual terminology of Printing Arts - Part 5: Screen Printing Terms-Supersedes BS ISO 12637-2: 1997;

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 67 of 68

199200

201

Page 68: docs.oasis-open.org · Web viewSource Doc Number Pub Date Title ASME B18.12 1/1/2001 Glossary of Terms for Mechanical Fasteners ASME SEC II A SA-751 7/1/2004 SA-751 Specification

Source

Doc Number

Pub Date Title

BSI BS ISO 16165

8/15/2001 Ships and Marine Technology - Marine Environment Protection - terminology Relating to Oil Spill Response

BSI BS ISO 16642

9/15/2003 Computer applications in terminology Terminological markup framework

BSI DD IEC TS 62282-1

4/18/2005 Fuel cell technologies Part 1: terminology

BSI PD R009-002

8/15/1999 Railway Applications - Guide for the Use of the terminology for Testing Procedures

OASIS-materials-draft-spec-06-6-2006 06 June 2006Copyright © OASIS Open 2006. All Rights Reserved. Page 68 of 68

2951

202203

204