Embed Size (px)
Citation preview
Page 1
Data sheet
Important: read the present data sheet before putting the unit in operation.
CODEInlet DSP DN 40- 1308Inlet Storz C/52 – 9038Inlet Storz B/75 – 9039Male inlet thread G 2'' B – 9037Female thread inlet 1.5 '' NST - 9963
Expansion tube
¼ turn valve
Operating handle
Inlet coupling
Handle
MATERIALS OF CONSTRUCTION
Construction in light aluminum alloy AGS T5Hard anodized body / corrosion resistant Teflon impregnation or polyester paintConnectors in stainless steelAxle in BronzeSeals in Nitrile
PERFORMANCE
Flow rate: 400 or 600 or 800 L/min – 105 or 158 or 210 GPMOpening and closing with ¼ turn valveEasy operation by two handle pointsPressure gauge from 0 to 16 bar
Pressure gauge
Bumper
Doc 1733 EN.des
DATA SHEETFOAM BRANCHPIPES
MEDIUM EXPANSION 400/600/800 LPMWITH DIN BALL VALVE SHUTOFF
POK S.A. FRANCE - z.i. "Les Guignons" - 10400 Nogent-sur-Seine - Tél : (33) 03 25 39 84 78 - Fax : (33) 03 25 39 84 90 - E-mail : - Web-site : POK OF NORTH AMERICA INC. - 500 Henry Street - Cambridge, Maryland, USA 21613 - Tel : 410.901.9900 - Fax : 410.901.9160 - E-mail : - Web-site :
POK CHINA - Room 788, Poly Plaza Office Building No.14, DongZhiMen South Ave , DongCheng District, Beijing 100027, China . Tel: 86-10-64667868 Fax: 86-10-64678864- E-mail : - Web-site :
[email protected] [email protected] www.pokfire.com
[email protected] www.pokfire.com
OPERATING INSTRUCTIONSThis material is intended for trained personnel in firefightingFailure to comply with these instructions and the use of the foam branchpipe above the recommended pressure can be dangerous and can even lead to death.For fires in electrical installations, it is necessary to
1) shut down electrical power as soon as possible2) maintain the biggest possible security distance
Before putting the foam branchpipe in operation, verify:no piece of the equipment has been damaged, broken or missingthe foam branchpipe should not be blockedthe inlet coupling should be connected to the supply hose
We recommend to clean the apparatus with clean water, exterior and interior (operation under pressure) after each use.In the case of repeated use with sea water or brackish water, it is recommended once per year to demount the foam branchpipe and clean all the pieces and reassemble it by following the maintenance procedure (which is in the spare part kit provided upon request). This work can be done in our workshop for which you can request a quote.
PERFORMANCE LIMITS
The foam branchpipe is guaranteed for functioning at the maximum service pressure of 16 bar.Unless stated otherwise, our guarantee does not cover usage above these hydraulic characteristics.
Page 2
Doc 1733 EN.des
DATA SHEETFOAM BRANCHPIPES
MEDIUM EXPANSION 400/600/800 LPMWITH DIN BALL VALVE SHUTOFF
POK S.A. FRANCE - z.i. "Les Guignons" - 10400 Nogent-sur-Seine - Tél : (33) 03 25 39 84 78 - Fax : (33) 03 25 39 84 90 - E-mail : - Web-site : POK OF NORTH AMERICA INC. - 500 Henry Street - Cambridge, Maryland, USA 21613 - Tel : 410.901.9900 - Fax : 410.901.9160 - E-mail : - Web-site :
POK CHINA - Room 788, Poly Plaza Office Building No.14, DongZhiMen South Ave , DongCheng District, Beijing 100027, China . Tel: 86-10-64667868 Fax: 86-10-64678864- E-mail : - Web-site :
[email protected] [email protected] www.pokfire.com
[email protected] www.pokfire.com
Doc 1733 EN.des
DATA SHEETFOAM BRANCHPIPES
MEDIUM EXPANSION 400/600/800 LPMWITH DIN BALL VALVE SHUTOFF
POK S.A. FRANCE - z.i. "Les Guignons" - 10400 Nogent-sur-Seine - Tél : (33) 03 25 39 84 78 - Fax : (33) 03 25 39 84 90 - E-mail : - Web-site : POK OF NORTH AMERICA INC. - 500 Henry Street - Cambridge, Maryland, USA 21613 - Tel : 410.901.9900 - Fax : 410.901.9160 - E-mail : - Web-site :
POK CHINA - Room 788, Poly Plaza Office Building No.14, DongZhiMen South Ave , DongCheng District, Beijing 100027, China . Tel: 86-10-64667868 Fax: 86-10-64678864- E-mail : - Web-site :
[email protected] [email protected] www.pokfire.com
[email protected] www.pokfire.com
INSTALLATION
Connect the foam branchpipe to an eductor with a supply hoseConnect the eductor to a pump via a supply hoseAttention: you must use an eductor adapted to the foam hose and take into account the pressure loss in the hosesUse a pump that is sufficiently powerful to obtain a pressure of 5 bar at the inlet of the foam branchpipe.
USAGE
Start the pump and increase the pressure to obtain 5 bar at the inlet of the foam branchpipe.Insert the suction hose in the foam containerThe foam is automatically sucked and mixed with water to produce a pre-mix.The foam is created at the outlet of the foam branchpipe.The length of the hoses affects the pressure loss. Take this into account.
Pump
Installation diagram
Foam
Foam branchpipe in operation
5 bar minimum
Page 3
Foam branchpipe
Eductor
Pump
Foam
Foam branchpipe
Eductor
