Dimensiones de Catarinas

1) Relacin = 1500 / 375 = 4 2) Potencia corregida = 5 HP x 1,50 (Factor de servicio) = 7,5 HP 3) Cadena 5/8 x 3/8 (15,87 x 9,70) simple hilera con pin de 19 dientes. 4) Rueda: 19 dientes x 4 (Relacin de transmisin) = 76 dientes.

Suministrar los siguientes datos:

C) Luz interior. D) Dimetro de rodillo. E) Cantidad de hileras (Simple, Doble o Triple) y de ser doble o triple, indicar el paso transversal. F) Especificar si se necesitan Uniones o Medias Mallas.

ANGEL LARREINA S.A.Moreno 901 (C1091AAS) - Buenos Aires

Tel.: 011-4334-2808 (lneas rot.) - Fax: 011-4334-3480

http://www.angellarreina.com - [email protected]

Velocidad de la mquina accionada: 375 RPM Motor elctrico de 5 HP trabajando 24hs. diarias con servicio semi-pesado.

COMO SELECCIONAR UN MANDO A CADENA

Calcular un mando a cadena con los siguientes datos:

Velocidad eje motriz: 1500 RPM

engranajes. B) Velocidades excesivas para la cadena de simple hilera elegida (ver velocidades mximas al pie de las tablas de potencia).

6) Se optar por cadena de doble o triple hilera (Doble o Triple capacidad de potencia) en el supuesto caso de que surjan algunos de los inconvenientes que a continuacin se enumeran:

A) Limitaciones de espacio que obliguen a elegir una cadena de menor paso, resultando por lo tanto ms chicos los

A) Dimetro exterior accesible al lugar disponible. B) Dimetro de la maza adecuada para el eje en que se va a montar (ver tabla de dimensiones). De resultar escasa, se tomar un pin mayor y se aumentar proporcionalmente la rueda, manteniendo siempre la relacin de transmisin.

B) Paso.

C) Ancho mximo que no exceda el disponible (ver tabla de dimensiones) y controlar a la vez el ancho exterior sobre cabezas de pernos en la cadena elegida.

COMO PEDIR UNA CADENA

A) Longitud (en metros, en pasos o cantidad de rodillos).

EJEMPLO DE CALCULO

proporcionalmente la cantidad de dientes del pin para mantener la relacin de transmisin. 5) Controlar si los engranajes elegidos renen las dimensiones necesarias para el caso:

para transmitir los HP ya corregidos, evitando en lo posible usar piones menores de 15 dientes. 4) Multiplicar la cantidad de dientes del pin por la relacin de transmisin para establecer los dientes de la rueda. En caso de resultar una cantidad de dientes fuera de lo normal, se optar por la mas prxima, aumentado o disminuyendo

3) Buscar en las tablas de potencia, en base a las RPM del eje motriz, qu cadena y cantidad de dientes son necesarios

1) Establecer la relacin de transmisin dividiendo las RPM del eje motriz por las RPM del eje accionado. No es conveniente proyectar mandos con relaciones mayores de 8 a 1.

5) La clsica elasticidad de la cadena, sumada a la pelcula lubricante que se forma entre las partes movibles, amortiguan los golpes por cargas intermitentes.

2) Corregir la potencia a transmitir por medio de la tabla de factores de servicio.

1) No se producen resbalamientos. 2) Se mantiene constante la relacin de velocidades. 3) El rendimiento es elevado: 98%. 4) La carga repartida sobre varios dientes del pin prolonga la vida til de la cadena.

engranajes respectivos, como as tambin el montaje y lubricacin adecuados.

Las transmisiones a cadena renen las siguientes ventajas:

TRANSMISIONES POR CADENAS DE RODILLOS

El accionamiento por medio de cadena de rodillos y engranajes, constituye un slido y seguro sistema de transmisin de la energa mecnica. Para obtener un resultado ptimo de una transmisin de este tipo, es fundamental seleccionar correctamente la cadena y

8 - 10 hs. 24 hs. 8 - 10 hs. 24 hs.1,00 1,25 1,25 1,501,25 1,50 1,50 1,751,50 1,75 1,75 2,00

para que penetre en todos los pernos, bujes y rodillos. Luego, dejar escurrir fuera del bao caliente y volver a colocar sobre los engranajes. C) Observar peridicamente el estado de los diversos elementos componentes.


Tel.: 011-4334-2808 (lneas rot.) - Fax: 011-4334-3480


Condiciones de Trabajo


TABLA DE FACTORES DE SERVICIOEs aconsejable al calcular un mando a cadena, tener en cuenta la tabla de factores de servicio siguiente:

Procedimiento para su uso:

Semi PesadoPesado

Motor Elctrico Motor Diesel

Uniforme

B) Lo mas frecuentemente posible, quitar la cadena, lavarla a fondo con nafta y sumergirla en aceite pesado o grasa caliente,

Multiplicar la potencia a transmitir por el factor correspondiente a las condiciones de trabajo y con ese valor proceder como indica el punto 3.

LUBRICACION

A) Por goteo: desde las RPM mas bajas hasta la primer cifra destacada de las RPM en la tabla de potencias. B) Por bao: entre las dos cifras destacadas en la misma tabla. C) Por bomba: desde la segunda cifra destacada hasta las RPM mximas. El lubricante adecuado para una temperatura ambiente de 5 a 40 C, es el SAE 30.

INSTALACION

La correcta instalacin de una transmisin por cadena de rodillos es factor preponderante en la duracin y eficacia del mando. Es aconsejable prestar atencin a los siguientes puntos: A) Montar slidamente los engranajes sobre los ejes, con chaveta y prisionero para sujetar la misma. B) Ubicar los engranajes lo mas cerca posible de los cojinetes de apoyo. C) Alinear con sumo cuidado ambos engranajes entre s y controlar el perfecto paralelismo de los ejes. D) Prever la posibilidad de variar la distancia entre ambos ejes, para facilitar el mantener la tensin correcta de la cadena, que no debe estar muy tensa, ni muy floja. E) No colocar una cadena nueva sobre engranajes desgastados o viceversa, pues resulta perjudicial para el elemento nuevo.

Para mantener adecuadamente una instalacin, es conveniente cuidar los siguientes detalles:

A) Tipo de lubricacin correcta de acuerdo a la velocidad de la cadena.

MANTENIMIENTO

Por goteo Por bao Por bomba

NOTA: Normalmente los piones y ruedas se entregan con agujero central chico, para luego ser agrandado a la medida deseada por el usuario.

La formula para hallar el largo de la cadena (expresado en pasos), conocindose la distancia entre ejes en pasos y la cantidad de dientes de la rueda y pin, es la siguiente:

Donde: L = Longitud de la cadena expresada en pasos.C = Distancia entre ejes expresado en pasos.N = Nmero de dientes de la rueda.n = Nmero de dientes del pin.

Una vez obtenido el resultado en pasos, se multiplica por el paso de la cadena en mm y se logra as la longitud de la cadena en mm.

EJEMPLO DE CALCULO

Para una cadena paso 15,88 mm (5/8") calcular su longitud, siendo:

C = 450 mm = 28,34 pasos N = 76 dientes Luego: n = 19 dientes

o sea: L = 56,80 + 47,50 + 2,90 = 107,08 pasos

y finalmente: L = 107,08 x 15,88 = 1700,43 mm


Tel.: 011-4334-2808 (lneas rot.) - Fax: 011-4334-3480


UNION: Es la pieza necesaria para empalmar entre s los extremos de una cadena.

MEDIA MALLA: Es el elemento necesario para quitar o aadir un solo paso de cadena y poder ajustar as, la tensin de la

LARGO DE LA CADENA

Dentro de una amplia escala, est determinada como distancia mnima entre ejes, la equivalencia de: Una vez el dimetro de la rueda grande mas la mitad del dimetro del pin.

DISTANCIA ENTRE EJES

mando es elevada.

misma, especialmente cuando se trata de distancias fijas entre ejes.

C) Dimetro del eje en que ser montado.

Las distancias excesivas tampoco son convenientes, por la flexin y el peso de la cadena.

Los mandos a cadena no tienen centros precisamente limitados, a menos que ello sea una necesidad determinada por losrganos accionados. Es conveniente tener presente que una distancia demasiado corta, es causa de desgaste prematuro de la cadena, con el inconveniente adems, de reducir la cantidad de dientes engranados, particularmente cuando la relacin del

ACCESORIOS PARA LAS CADENAS

B) Datos de la cadena correspondiente segn se detalla en: "Como pedir una Cadena".


COMO PEDIR UN PION O RUEDA

Suministrar los siguientes datos: A) Cantidad de dientes (ver tabla de dimensiones de ruedas y piones)

Unin Media malla largaMedia malla corta

N n L = 2 C + N + n + 2 x 3,14 2 C

76 19 L = 2 x 28,34 + 76 + 19 + 2 x 3,14 2 28,34

Paso Transversal

Tmm Pulgadas mm Pulgadas mm Pulgadas mm Kg.

6,35 * 1/4 3,17 1/8 3,30 0,130 6,45 400 ASA 258 0,314 3 0,118 5 0,196 5,64 450 BS

9,53 3/8 4,76 3/16 5,08 0,200 10,16 950 ASA 35 9,53 * 3/8 5,70 7/32 6,35 1/4 10,24 910 BS 12,70 * 1/2 3,30 1/8 7,75 0,306 ---- 800 BS

12,70 1/2 4,90 3/16 7,75 0,306 ---- 850/1100 BS12,70 1/2 5,20 0,204 8,51 0,334 ---- 1800 BS12,70 1/2 6,35 1/4 7,75 0,306 ---- 910/1500 ASA 4112,70 1/2 6,35 1/4 8,51 0,334 ---- 1800 BS12,70 1/2 7,91 5/16 7,91 5/16 14,30 1600 ASA 40

12,70 * 1/2 7,91 5/16 8,51 0,334 13,92 1800 BS15,80 5/8 6,35 1/4 10,16 0,400 ---- 2600 ASA

15,80 * 5/8 9,52 3/8 10,16 0,400 17,95 2600 ASA 50 15,80 * 5/8 9,70 3/8 10,16 0,400 16,59 2500 BS 19,05 * 3/4 12,70 1/2 11,91 0,469 22,65 3300 ASA 60 19,05 * 3/4 11,70 7/18 12,07 0,474 19,46 3100 BS 25,40 * 1 15,80 5/8 15,80 5/8 29,46 6500 ASA 80 25,40 * 1 17 0,669 15,80 5/8 31,83 6500 BS 31,75 * 1 1/4 19,05 3/4 19,05 3/4 35,84 10500 ASA 100 31,75 * 1 1/4 19,60 3/4 19,05 3/4 36,45 10500 BS 38,10 * 1 1/2 25,40 1 22,22 7/8 45,62 15000 ASA 120

38,10 1 1/2 25,40 1 25,40 1 48,36 16000 BS 44,45 * 1 3/4 25,40 1 25,40 1 49 20500 ASA 140

44,45 1 3/4 31 1 1/4 27,94 1,100 59,56 21000 BS 50,80 * 2 31,75 1 1/4 28,57 1 1/8 58,44 26000 ASA 160

50,80 2 31 1 1/4 29,21 1,150 58,55 26000 BS 63,50 * 2 1/2 38,10 1 1/2 39,67 1,560 71,12 43000 ASA 200

63,50 2 1/2 38,10 1 1/2 39,37 1,550 72,29 42000 BS

Nota: Las cadenas de 2 o ms hileras de rodillos son de idnticas medidas que las de simple hilera, siendo su carga de rotura 2 o msveces mayor segn sea la cantidad de hileras.

Al proyectar instalaciones nuevas es conveniente adoptar las cadenas marcadas con el asterisco, pues son de ms facil reposicin,como as tambien los respectivos engranajes.

ASA: Norma AmericanaBS: Norma Britnica


Tel.: 011-4334-2808 (lineas rot.) - Fax: 011-4334-3480


TRANSMISIONES POR CADENAS DE RODILLOSCADENAS DE RODILLOS DE USO MAS COMUN

DIAM. DEL RODILLO

D

Carga de Rotura Norma

PASO

P

LUZ INTERIOR

W

MacizoSolid

Cubo soldadoWelded Hub

Pieza soldadaWelded Piece

M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

Paso - Pitch 1/4" ASA 25 Rodillo - Roller 3,3 mm 6,35 mm

Discos, Piones y Ruedas de Aceropara Transmisiones de CadenasSprockets and Plate Wheels for Roller Chain

1011121314151617181920212223242526272829303845577695

20.5522.5424.5326.5328.5430.5432.5534.5636.5738.5840.5942.6144.6246.6348.6550.6652.6854.7056.7158.7360.7576.9091.03

115.27153.66192.06

23.3525.4427.5129.5731.6333.6835.7337.7839.8241.8643.9045.9447.9850.0152.0454.0856.1158.1460.1762.2064.2380.4494.62

118.91157.34195.76

1316162020252628303034343440404040444450506060656565

DimetroPrimitivo(d)

Z

S

1316162020252628303034343440404040444450506060656565

D

1515151515151515152020202020202525252525252828282828

S

2424242424242424242929292929293434343434343737373737

D

DimetroExterior(A)

Pitch Circle Diameter(d)

TopDiameter(A)

Dimetro Cubo(B)Hub Diameter(B)

Largo Total(C)Total Length(C)

Dimensiones para tipo Americano - (ASA - ANSI)Measurement for American type (ASA - ANSI)

PASO/PitchASA25 (1/4)

T2.8

N3.6

M29.2

M3-

T12.8

Los dimetros y largos estn sujetos a modificacin sin previo aviso por razones de fabricacin.Diameters and lenghts can be modified without any previous advise due to production reasons.

DARIOlogo3

Potencia expresada en HP/Power in HP

Potencia Engranajes para cadena paso 1/4" (ASA 25)Potencia Engranajes para cadena paso 1/4" (ASA 25)

11121314151617181920212223242526283032354045

Ndientes

Z

0.050.060.060.070.070.080.080.090.090.100.110.110.120.130.130.140.150.160.170.190.220.25

100

0.230.250.270.300.320.340.370.390.410.440.460.480.510.530.560.580.630.680.730.800.921.05

500

0.390.430.470.500.540.580.620.660.700.740.780.820.860.900.940.981.071.151.231.361.571.78

900

0.500.550.600.650.700.760.810.860.910.961.011.071.121.171.221.281.381.491.601.762.032.31

1200

0.730.800.870.941.011.091.161.241.311.381.461.531.611.691.761.841.992.152.302.532.933.32

1800

0.981.071.171.271.361.461.561.661.761.861.962.062.162.272.372.472.682.883.093.413.934.47

2500

1.151.261.381.491.611.721.841.962.072.192.312.432.552.672.792.913.153.403.644.014.645.26

3000

1.321.451.581.711.851.982.112.252.382.522.662.792.933.073.213.343.623.904.184.615.326.05

3500

1.381.571.771.932.082.232.382.532.692.842.993.153.303.463.613.774.094.404.725.206.006.82

4000

1.161.321.491.661.842.032.222.422.622.833.053.273.503.733.964.194.544.895.255.786.687.58

4500

0.991.121.271.421.571.731.902.072.242.422.602.792.983.183.383.594.014.454.905.606.858.17

5000

0.860.971.101.231.361.501.641.791.942.102.262.422.592.762.933.113.473.854.254.865.937.08

5500

0.750.860.961.081.201.321.441.571.701.841.982.122.272.422.572.733.053.383.734.265.216.21

6000

0.670.760.860.961.061.171.281.391.511.631.761.882.012.152.282.422.703.003.303.784.625.51

6500

0.600.680.770.860.951.051.141.251.351.461.571.691.801.922.042.172.422.682.963.384.134.93

7000

0.540.610.690.770.860.941.031.121.221.321.421.521.621.731.841.952.182.422.673.053.734.45

7500

0.490.560.630.700.780.860.941.021.111.201.291.381.471.571.671.771.982.202.422.773.384.04

8000

0.450.510.570.640.710.780.860.931.011.091.171.261.351.441.531.621.812.012.212.533.093.69

8500

0.410.470.530.590.650.720.790.860.931.001.081.161.241.321.401.491.661.842.032.322.833.38

9000

0.350.400.450.500.560.610.670.730.790.860.920.991.061.121.201.271.421.571.731.982.422.89

10000

Revoluciones por minuto (RPM) engranaje ms chico - RPM Sprocket

Factores de hileras mltiplesMultiple Line Factor

Hileras 1234

Factor hilera 1.0 1.9 2.8 3.7

Esta tabla equivale a engranajes de una hilera de dientes, multiplicar por el factor de hileras mltiples para engranajes de mayor cantidad de hileras.

The values shown above are for simplex sprockets. Use the multiple line factor according to the sprocket lines.

DARIOlogo3

MacizoSolid



M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

Paso - Pitch BS 05 Rodillo - Roller 5 mm 8 mm


1011121314151617181920212223242526272829303845577695

25.8928.4030.9133.4335.9538.4841.0143.5446.0748.6051.1453.6856.2158.7561.2963.8366.3768.9171.4573.9976.5396.88

114.68145.22193.59241.96

29.0031.6034.0036.7039.3041.8044.5047.0049.8052.5055.0057.7060.0062.7065.0067.8070.0073.0075.0078.0080.50

100.80118.60149.20197.50246.00

1718202325283034344040444450505050555555656565656565

Z

S

1718202325283034344040444450505050555555656565656565

D

1515151515202020202025252525252528282828282828282828

S

2323232323282828282833333333333336363636363636363636

D

Dimensiones para tipo Europeo - (BS - ISO)Measurement for European type (BS - ISO)

PASO/Pitch05 - 8 mm

T2.7

N2.9

M28.3

M3-

T12.8

DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




DARIOlogo3

MacizoSolid



M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

Paso -Pitch 3/8" ASA 35 Rodillo - Roller 5,08 mm 9,52 mm BS 06 Rodillo - Roller 6,35 mm


9101112131415161718192021222324252627282930353840455057607695

114

27.8530.8233.8136.8039.8042.8045.8148.8251.8454.8557.8760.8963.9166.9369.9572.9776.0079.0282.0585.0788.1091.12

106.26115.34121.40136.55151.69172.91182.00230.49288.08345.68

31.8835.0338.1541.2644.3647.4550.5353.6056.6759.7362.8065.8568.9171.9675.0178.0681.1184.1687.2190.2593.3096.34

111.55120.66126.74141.93157.11178.36187.46236.01293.64351.26

Z



T4.1

N6

M214.2

M324.3

T14.3


PASO/Pitch06 - 3/8

T5.2

N5

M215.4

M325.6

T15.2

1720222528313437404345464850525457606060606065707070707070709090

17202225283134374043464852555861646770737679808080808080808090

100

1720222528313437404346485255586164677073767980808090909090

100100100

2222252525252528282828282828282828282828282830303032323235354040

2525303030303030303030303030303030303030303040404040404040404545

4040404040404040404040404040404040404040404040404056565656566060

S D T S D T

DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




DARIOlogo3


11121314151617181920212223242526283032354045

Ndientes

Z

0.180.200.220.240.250.270.290.310.330.350.370.380.400.420.440.460.500.540.580.640.730.83

100

0.770.850.931.011.081.161.241.321.401.481.561.641.721.801.881.962.122.292.452.703.123.55

500

1.311.441.571.711.841.972.102.242.372.512.642.782.923.053.193.333.613.894.174.595.306.02

900

1.701.872.042.212.382.552.732.903.073.253.423.603.783.964.134.314.675.035.405.956.877.80

1200

2.452.702.943.183.433.683.934.184.434.684.935.195.445.705.956.216.737.257.778.569.89

11.20

1800

3.303.623.954.284.614.945.285.615.956.296.636.977.317.668.008.359.059.74

10.4011.5013.3015.10

2500

2.943.353.774.224.685.155.646.156.677.207.758.218.629.029.439.84

10.7011.5012.3013.6015.7017.80

3000

2.332.663.003.353.714.094.484.885.295.726.156.597.057.517.998.479.47

10.5011.6013.2016.2019.30

3500

1.912.172.452.743.043.353.673.994.334.685.035.405.776.156.546.937.758.599.47

10.8013.2015.80

4000

1.601.822.052.302.552.813.073.353.633.924.224.524.835.155.485.186.497.207.939.08

11.1013.20

4500

1.371.561.751.962.172.402.622.863.103.353.603.864.134.404.684.965.556.156.777.759.47

11.30

5000

1.181.351.521.701.882.082.272.482.692.903.123.353.583.814.054.304.815.335.876.728.219.79

5500

1.041.181.331.491.651.822.002.172.362.552.742.943.143.353.563.774.224.685.155.907.208.59

6000

0.921.051.181.321.471.621.771.932.092.262.432.612.792.973.163.353.744.154.575.236.397.62

6500

0.820.941.061.181.311.451.581.731.872.022.172.332.492.662.823.003.353.714.094.685.726.82

7000

0.740.850.951.071.181.301.431.561.691.821.962.102.252.402.552.703.023.353.694.225.15

-

7500

0.670.770.870.971.071.181.301.411.531.651.781.912.042.172.312.452.743.043.353.834.68

-

8000

0.620.700.790.880.981.081.181.291.401.511.621.741.851.992.112.242.502.773.063.50

--

8500

0.570.640.730.810.900.991.091.181.281.391.491.601.711.821.942.052.302.552.813.21

--

9000

0.480.550.620.690.770.850.931.011.101.181.271.371.461.561.651.751.962.17

----

10000


Hileras 1234






DARIOlogo3

MacizoSolid



DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




Paso - Pitch 1/2" ASA 40 Rodillo - Roller 7,925 mm 12,7 mm BS 08 Rodillo - Roller 8,51 mm

9101112131415161718192021222324252627282930353840455057607695

114

37.1341.1045.0849.0753.0757.0761.0865.1069.1273.1477.1681.1885.2189.2493.2797.30

101.33105.36109.40113.43117.46121.50141.68153.79161.87182.06202.26230.54242.66307.32384.11460.91

42.5146.7150.8755.0259.1563.2667.3771.4775.5679.6583.7387.8091.8895.95

100.02104.09108.15112.21116.28120.34124.39128.45148.73160.89168.99189.24209.48237.81249.95314.68391.52468.35

2426293337414550525660646870707070707070808070707070707080808080

242832353842465054586266707070758085859095

1001009090909090

100100100100

242832353842465054586266707070758085859095

100100100100100100100100100120120

2828282828282828282828282828282828303030303040404040404040404545

3535353535353538383838384040404040404040404050505050505050565663

5050505050505050505050505555555555555555555560606060606060606767

Z

S D T S D T



T7

N7.4

M221.4

M335.8

T17.2


PASO/Pitch08 - 1/2

T7.1

N6.8

M221

M334.9

T17.1


M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

DARIOlogo3


11121314151617181920212223242526283032354045

Ndientes

Z

0.230.250.280.300.320.350.370.390.420.440.460.490.510.540.560.580.630.680.730.810.931.06

50

0.430.470.520.560.600.650.690.730.780.820.870.910.961.001.051.091.181.271.361.501.741.97

100

0.800.880.961.041.121.201.291.371.451.531.621.701.781.871.952.042.202.382.552.813.243.68

200

1.501.651.801.952.102.252.402.552.712.863.023.173.333.483.643.804.114.434.755.246.056.87

400

1.832.012.202.382.562.752.933.123.313.503.693.884.074.264.454.645.035.425.816.407.398.40

500

2.482.732.973.223.473.723.974.224.484.734.995.255.515.766.026.286.817.337.868.66

10.0011.40

700 900

3.113.423.734.044.354.664.985.305.625.946.266.586.907.237.557.888.549.209.86

10.9012.5014.20

1200

4.635.095.556.016.476.947.417.888.368.839.319.79

10.3010.8011.2011.7012.7013.7014.7016.2018.7021.20

1800

4.665.315.996.707.438.188.969.76

10.5011.1011.7012.3012.9013.5014.1014.7015.9017.2018.4020.3023.4026.60

2400

3.033.453.894.354.825.315.826.346.887.437.998.579.139.7610.4011.0012.3013.6015.0017.2021.0025.10

3000

2.172.472.793.113.453.804.174.544.925.315.726.136.556.997.437.888.809.7610.8012.3015.0017.90

3500

1.721.962.212.472.743.023.313.603.914.224.544.875.205.545.896.256.997.758.649.7611.9014.20

4000

1.011.151.291.451.601.771.942.112.292.472.662.853.053.253.453.664.094.545.005.766.99

-

1.411.601.812.022.242.472.712.953.203.453.713.984.264.544.825.125.726.346.997.999.7611.70

5000

0.770.870.981.101.221.341.471.601.741.882.022.172.312.472.632.793.113.45

----

6000

0.610.690.780.870.971.071.171.271.381.491.601.721.841.96

--------

7000

0.500.570.640.710.790.870.96

---------------

8000


Hileras 1234







DARIOlogo3

MacizoSolid



M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T



9101112131415161718192021222324252627282930353840455057607695

114

46.4251.3756.3561.3466.3371.3476.3581.3786.3991.4296.45

101.48106.51111.55116.59121.62126.66131.70136.74141.79146.83151.87177.10192.24202.33227.58252.82288.18303.33384.15480.14576.13

53.1458.3863.5968.7773.9379.0884.2189.3394.4599.56

104.66109.76114.85119.94125.02130.11135.19140.27145.34150.42155.49160.57185.91201.11211.24236.55261.85297.26312.44393.35489.40585.44

303537424752576060707075758080808085859090908080808090909090

100100

303539444954596469747984859095

100105110110115115120100100100100100100100100110110

303539444954596469747984859095

100105110110115115120100100100100100100100110120120

3030303030303030303030303030303030353535353540404040454550505656

4040404040404045454545454545454545454545454550505050505050506363

6060606060606060606060606060606060606060606060606060636367677070

Z

S D T S D T


PASOASA50 (5/8)

T8.4

N9.7

M226.5

M344.6

T18.7


PASO10 - 5/8

T9

N7.6

M225.6

M342.2

T19

DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




DARIOlogo3


11121314151617181920212223242526283032354045

Ndientes

Z

0.450.490.540.580.630.670.720.760.810.860.900.951.001.041.091.141.231.331.421.571.812.06

50

0.840.921.001.091.171.231.341.431.511.601.691.771.861.952.032.122.302.492.662.933.383.84

100

2.252.472.702.923.153.383.613.834.074.304.534.765.005.235.475.706.186.667.147.869.08

10.30

300

3.573.924.274.634.995.355.716.076.446.807.177.547.918.298.669.039.79

10.5011.3012.5014.4016.30

500

6.066.657.257.868.479.089.69

10.3010.9011.5012.2012.8013.4014.1014.7015.3016.6017.9019.2021.1024.4027.70

900

7.858.629.40

10.2011.0011.8012.6013.4014.2015.0015.8016.6017.4018.2019.0019.9021.5023.2024.9027.4031.6035.90

1200 1400

8.139.26

10.4011.7012.6013.5014.4015.3016.3017.2018.1019.1020.0020.9021.9022.8024.7026.6028.6031.5036.0041.30

1800

5.586.347.168.018.889.78

10.7011.7012.7013.7014.7015.8016.9018.0019.1020.3022.6025.1027.7031.6038.7046.10

2100

4.425.045.696.357.057.768.509.26

10.0010.8011.7012.5013.4014.3015.2016.1018.0019.9022.0025.1030.7036.60

2400

3.624.134.655.205.776.356.967.588.228.889.5510.2011.0011.7012.4013.2014.7016.3018.0020.6025.1030.00

2700

3.043.463.904.364.835.325.836.356.897.448.018.599.189.7810.4011.0012.3013.7015.1017.2021.0025.10

3000

2.592.953.333.724.134.554.985.425.886.356.847.397.848.368.889.4210.5011.7012.9014.7018.0021.40

3500

1.681.922.162.422.682.953.233.523.824.134.444.765.095.425.776.126.847.588.329.55

--

2.062.342.642.953.273.613.954.304.675.045.425.826.226.337.057.478.359.2610.2011.7014.30

-

4000

1.411.641.812.032.252.472.712.953.203.463.723.994.274.554.835.135.73

-----

4500

1.201.371.551.731.922.112.312.522.732.953.183.41

----------

5000

1.041.191.341.501.661.832.01

---------------

5500

1.041.191.341.501.661.832.01

---------------

5500 6000


Hileras 1234


0.921.04

--------------------





DARIOlogo3

MacizoSolid



M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

Paso - Pitch 3/4" ASA 60 Rodillo - Roller 11,913 mm19,05 mm BS 12 Rodillo - Roller 12,07 mm


9101112131415161718192021222324252627282930353840455057607695

114

55.7061.6567.6273.6079.6085.6191.6397.65

103.67109.70115.74121.78127.82133.86139.90145.95151.99158.04164.09170.14176.19182.25212.52230.69242.80273.09303.39345.81363.99460.98576.17691.36

63.7770.0676.3182.5388.7294.89

101.05107.20113.34119.47125.59131.71137.82143.93150.03156.13162.23168.32174.41180.50186.59192.68223.09241.33253.48283.86314.22356.72374.93472.02587.28702.53

3742465258647075808080809090909095959595959590

100100100100100100100100100

3742475359657177838995

100100100110110120120120120120120100110110110120120120130130130

3742475359657177838995

100100100110110120120120120120120120120120120140140140150160160

3535353535353535353535354040404040404040404040404056565656566565

5656565656565656565656565656565656565656565663636363636363637070

7070707070707070707070707070707070707070707080808080808080809090

Z

S D T S D T



T11.3

N11.5

M234.1

M3 56.9

T111.7


PASO12 - 3/4

T10.9

N8.6

M230.4

M349.8

T110.9

DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




DARIOlogo3


11121314151617181920212223242526283032354045

Ndientes

Z

0.770.850.921.001.081.131.241.311.391.471.551.631.711.791.871.952.122.282.452.693.113.53

50

1.441.581.731.872.012.162.312.452.602.752.903.053.193.353.503.653.954.264.565.035.816.60

100

2.692.953.223.493.764.034.304.584.855.135.405.685.966.246.526.817.377.948.529.38

10.8012.30

200

6.136.747.347.968.579.199.81

10.4011.1011.7012.3013.0013.6014.2014.9015.5016.8018.1019.4021.4023.7028.10

500

8.309.129.94

10.8011.6012.4013.3014.4015.0015.8016.7017.5018.4019.3020.1021.0022.8024.5026.3029.0033.5038.00

700

10.4011.4012.5013.5014.5015.6016.7017.7018.8019.8020.9022.0023.1024.1025.3026.4028.5030.8033.0036.3042.0047.70

900 1200

11.9013.5015.2017.0018.8020.2021.6022.9024.3025.7027.1028.5029.9031.3032.7034.1037.0039.8042.7047.1054.4061.70

1400

9.4110.7012.1013.5015.0016.5018.1019.7021.4023.1024.8026.6028.4030.3032.2034.2038.2042.4046.7053.4062.5070.90

1600

7.708.779.89

11.1012.3013.5014.8016.1017.5018.9020.3021.8023.3024.8026.4028.0031.3034.7038.2043.7053.4063.70

1800

6.457.358.299.26

10.3011.3012.4013.5014.6015.8017.0018.2019.5020.8022.1023.4026.2029.1032.0036.6044.7053.40

2000

5.516.287.087.918.779.66

10.6011.5012.5013.5014.5015.6016.7017.8018.9020.0022.40

248.0027.3031.3038.2045.60

2500

3.944.495.065.666.289.617.578.258.959.66

10.4011.1011.9012.7013.5014.3016.0017.8019.6022.4027.3032.60

3000

2.382.713.063.423.794.174.574.985.405.836.286.737.197.678.158.65

------

3.003.423.854.314.775.265.766.286.817.357.918.489.079.66

10.3010.9012.2013.5014.9017.00

--

3500

1.952.222.502.803.103.423.744.084.42

-------------

4000

1.631.86

--------------------

4500


Hileras 1234






DARIOlogo3

MacizoSolid



Paso- Pitch 1" ASA 80 Rodillo - Roller 15,88 mm 25,4 mm BS 16 Rodillo - Roller 15,88 mm


9101112131415161718192021222324252627282930353840455057607695

114

74.2682.2090.1698.14

106.14114.15122.17130.20138.23146.27154.32162.37170.42178.48186.54194.60202.66210.72218.79226.86234.93243.00283.36307.58323.74364.12404.52461.08485.33614.64768.22921.81

85.0393.41

101.74110.03118.29126.52134.74142.93151.12159.29167.45175.61183.76191.90200.04208.17216.30224.43232.55240.67248.79256.90297.46321.77337.98378.48418.96475.62499.90629.36783.04936.70

50556169788492

100100100100100110110110110110120120120120120120120120120125125125140140150

50566472808896

104112120128130130130130130130130130130130130140140140140140150150150160160

50566472808896

104112120128130130130130130130130130130130130150150150150150160160160180180

4040404040404545454545455050505050505050505050505070707080808080

7070707070707070707070707070707070707070707070757575909090959595

100100100100100100100100100100100100100100100100100100100100100100100100100100100100115115120130

Z

S D T S D T


PASO/PitchASA80 (1)

T14.1

N15.2

M243.4

M372.7

T114.6


PASO/Pitch16 - 1

T15.5

N16.1

M247.7

M379.6

T115

DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

DARIOlogo3

Potencia Engranajes para cadena paso 1" (ASA 80)Potencia Engranajes para cadena paso 1" (ASA 80)

11121314151617181920212223242526283032354045

Ndientes

Z

0.971.061.161.251.351.451.551.641.741.841.942.042.142.242.342.452.652.853.063.373.894.4

25

1.81.982.162.342.522.72.883.073.253.443.623.81

44.194.374.564.945.335.716.297.278.25

50

3.363.694.034.364.7

5.045.385.726.076.416.767.117.467.818.168.529.239.9410.711.713.615.4

100

6.286.897.528.148.779.4110

10.711.312

12.613.613.914.615.215.917.218.519.921.925.328.7

200

9.049.9310.811.712.613.514.515.416.317.218.219.120.121

21.922.924.826.728.631.636.441.4

300

11.712.914

15.216.417.618.719.921.122.323.524.826

27.228.429.732.134.637.140.947.253.6

400

14.315.717.118.620

21.522.924.425.827.328.830.331.833.234.736.239.342.345.450

57.765.6

500

19.421.323.225.127.129313335373941434547

49.153.257.361.467.678.188.7

700

2326.229.131.534

36.438.941.443.846.348.951.453.956.459

61.566.771.877

84.898

111

900

19.622.325.228.231.234.437.741.144.548.151.755.559.362

64.867.673.378.984.693.3108122

1000

14.917

19.221.423.826.228.731.233.936.639.442.245.148.151.154.260.667.274

84.7103123

1200

11.813.515.217

18.920.822.724.826.929

31.233.535.838.240.643

48.153.358.767.282.198

1400

9.6911

12.513.915.417

18.620.322

23.825.627.429.331.233.235.239.443.648.155

67.280.2

1600

8.129.2510.411.712.914.215.617

18.419.921.423

24.626.227.829.533

36.640.346.156.367.2

1800

6.937.9

8.919.9611

12.213.314.515.717

18.319.621

22.323.825.228.231.234.439.447.154.1

2000

6.016.857.726.839.5710.511.512.613.614.715.917

18.219.420.621.824.427.129.834.120-

2200

5.276.016.787.578.4

9.2510.11112

12.913.914.915.917

18.119.221.423.826.2

---

2400

4.425.045.686.357.047.768.499.2510

10.511.712.513.414.215.116.1

------

2700

3.774.3

4.855.426.016.627.257.9

8.57-------------

3000

1.7---------------------

3400


Hileras 1234




Esta tabla equivale a engranajes de una hilera de dientes, multiplicar por el factor de hileras mltiples para engranajes de mayor cantidad de hileras.The values shown above are for simplex sprockets. Use the multiple line factor according to the sprocket lines.

DARIOlogo3

MacizoSolid



M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T



9101112131415161718192021222324252627282930353840455057607695

92.83102.75112.70122.67132.67142.68152.71162.75172.79182.84192.90202.96213.03223.10233.17243.25253.32263.41273.49283.57293.66303.75354.20384.48404.67455.15505.65576.35606.66768.30960.28

106.28116.77127.18137.54147.86158.16168.42178.67188.90199.11209.32219.51229.70239.88250.05260.22270.38280.53290.69300.84310.99321.13371.82402.22422.47473.10523.70594.53624.88786.69978.80

6570778898

10890

100100100100110110110110120120120120120120120130130130130140140140140150

65707788

10010890

100110120120120140140140180200200200200200200200140140140150150150160180

65707788

10010890

100110120120120140140140180200200200200200200200140140140150150150160180

45454545454550505050505055555555555555555555607070708080809090

8080808080808080808080808080808080808080808090909090

100100100110110

115115115115115115115115115115115115115115115115115115115115115115130130130130130130130140140

Z

S D T S D T


PASO/Pitch ASA100 (11/4)

T17

N18.8

M252.8

M388.6

T117.6


PASO/Pitch20 - 11/4

T18.2

N18.2

M254.6

M391.1

T118.2

DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




DARIOlogo3


11121314151617181920212223242526283032354045

Ndientes

Z

0.810.890.971.051.131.221.301.381.461.551.631.711.801.881.972.052.222.402.572.833.273.71

10

1.852.032.222.402.592.772.963.153.343.533.723.914.104.304.494.685.075.475.866.467.468.47

25

3.453.794.134.484.835.175.525.886.236.586.947.307.668.028.388.749.4710.2010.9012.0013.9015.80

50

6.447.087.728.369.019.6610.3011.0011.6012.3013.0013.6014.3015.0015.6016.3017.7019.0020.4022.5026.0029.50

100

12.0013.2014.4015.6016.8018.0019.2020.5021.7022.9024.2025.4026.7027.9029.2030.4033.0035.5038.1042.0048.5055.00

200

17.3019.0020.7022.5024.2026.0027.7029.5031.2033.0034.8036.6038.4040.2042.0043.8047.5051.2054.9060.4069.8079.30

300

22.4024.6026.9029.1031.4033.6035.9038.2040.5042.8045.1047.4049.8052.1054.4056.8061.5066.3071.1078.3090.40103

400

27.4030.1032.8035.6038.3041.1043.9046.7049.5052.3055.1058.0060.8063.7066.6069.4075.2081.0086.9095.70111.0126.0

500

32.3035.5038.7041.9045.2048.4051.7055.0058.3061.6065.0068.3071.7075.0078.4081.8088.6095.50102.0113.0130.0148.0

600

37.1040.8044.5048.2051.9055.6059.4063.2067.0070.8074.6078.5082.3086.2090.1094.00102.0110.0118.0130.0150.0170.0

700

32.8037.3042.1047.0052.2057.5063.0068.6074.4079.8084.2088.5092.8097.20102.0106.0115.0124.0133.0146.0169.0192.0

800

27.5031.3035.3039.4043.7048.2052.8057.5062.3067.3072.4077.7083.0088.5094.1099.80112.0124.0136.0156.0188.0213.0

900

23.4026.7030.1033.7037.3041.1045.0049.1053.2057.5061.8066.3070.9075.6080.3085.2095.20106.0116.0133.0163.0194.0

1000

20.3023.2026.1029.2032.4035.7039.0042.5046.1049.8053.6057.5061.4065.5069.60738082.5091.50101.0115.0141.0168.0

1100

17.8020.3022.9025.6028.4031.3034.3037.3040.5043.7047.0050.4053.9057.5061.1064.8072.4080.3088.50101.0124.0148.0

1200

15.8018.0020.3022.7025.2027.7030.4033.1035.9038.8041.7044.7047.8051.0054.2057.5064.2071.2078.5089.80110.0131.0

1300

14.2016.1018.2020.3022.5024.8027.2029.6032.1034.7037.3040.0042.8045.6048.5051.4057.5063.7070.2080.3098.10117.0

1400

11.6013.2014.9016.6018.4020.3022.3024.2026.3028.4030.6032.8035.0037.3039.7042.1047.0052.2057.5065.8080.3045.30

1600

9.7111.1012.5013.9015.5017.0018.7020.3022.0023.8025.6027.5029.4031.3033.3035.3039.4043.7048.2055.10

--

1800

8.299.4510.6011.9013.2014.5015.9017.4018.8020.3021.9023.4025.1026.7028.4030.1033.7010.00

----

2000

7.198.199.2310.3011.4012.8013.8015.0016.3017.6019.0020.307.74

---------

2200

6.317.198.109.0610.0011.1010.79

---------------

2400

1.29---------------------

2600


Hileras 1234





DARIOlogo3

MacizoSolid



Pitch Circle Diameter

TopDiameter

Dimetro CuboHub Diameter

Largo TotalTotal Length

M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

Paso 11/2" ASA 120 Rodillo 22,22 mm Roller 38.1 mm BS 24 Rodillo 25,4 mm


9101112131415161718192021222324252627282930353840455057607695

111.40123.29135.23147.21159.20171.22183.25195.29207.35219.41231.48243.55255.63267.72279.80291.90303.99316.09328.19340.29352.39364.49425.04461.37485.60546.19606.78691.62727.99921.96

1152.33

127.54140.12152.62165.05177.44189.79202.11214.40226.68238.94251.18263.41275.64287.85300.06312.26324.45336.64348.83361.01373.18385.36446.19482.66506.97567.72628.44713.43749.85944.03

1174.56

708090

102114100110120130130130130130140140140140140140150150150150150150150150150160160175

708090

102114100110130140140140180200200200200200200200200200160160160160160160160170170180

708090

102114100110130140140140180200200200200200200200200200160160160160160160160170170180

555555555560606060606060656565656565656565656590909090

100100100100

100100100100100100100100100100100100100100100100100100100100100100100110110110110120120120140

140140140140140140140140140140140140140140140140140140140140140140140140140140140140140140150

DimetroPrimitivo

Z

S D T S D T(1)

DimetroExterior


PASOASA120 (11/2)Chain Pitch

T22.7

T

N22.7

N

M268.1M2

M3 113.5

M3

T123.5T1


PASO24 - 1 1/2

Chain Pitch

T23.6

T

N24.8

N

M272M2

M3120.3M3

T123.6T1 (1) B.S. Largo Total ms 10 mm.


DARIOlogo3


11121314151617181920212223242526283032354045

Ndientes

Z

1.371.501.641.781.912.052.192.332.472.612.752.903.043.183.323.473.764.054.344.785.526.27

10

3.123.433.744.054.374.685.005.325.645.966.286.606.937.257.587.918.579.239.9010.9012.6014.30

25

5.836.406.987.568.158.749.399.9210.5011.1011.7012.3012.9013.5014.1014.8016.0017.2018.5020.3023.5026.70

50

10.9011.9013.0014.1015.2016.3017.4018.5019.6020.7021.9023.0024.1025.3026.4027.8029.8032.1034.5038.0043.9049.80

100

15.7017.2018.8020.3021.9023.5025.1026.7028.3029.9031.5033.1034.8036.4038.0039.7043.0046.3049.6054.7063.2071.70

150

20.3022.3024.3026.3028.4030.4032.5034.6036.6038.7040.8042.9045.0047.1049.3051.4055.7060.0064.3070.9081.8092.90

200

29.2032.1035.0037.9040.9043.8046.8049.8052.8055.8058.8061.8064.9067.9071.0074.0080.2086.4092.60102.0118.0134.0

300

37.9041.6045.4049.1053.0056.8060.6064.5068.4072.2076.2080.1084.0088.0091.9095.90104.0112.0120.0132.0153.0173.0

400

46.3050.9055.5060.1064.7069.4074.1078.8083.6088.3098.1097.90103.0108.0112.0117.0127.0137.0147.0162.0187.0212.0

500

54.6059.9065.3070.8076.3081.8087.3092.9098.50104.0110.0115.0121.0127.0132.0138.0150.0161.0173.0190.0220.0250.0

600

46.3052.8059.5066.5073.8081.3089.0097.00105.0114.0122.0131.0139.0146.0152.0159.0172.0185.0199.0219.0253.0287.0

700

37.9043.2048.7054.4060.4066.5072.8079.4086.1092.90100.0107.0115.0122.0130.0138.0154.0171.0188.0215.0263.0314.0

800

31.8036.2040.8045.6050.6055.7061.0066.5072.1077.9083.8089.9096.10102.0109.0115.0129.0143.0158.0180.0220.0263.0

900

27.1030.9034.9039.0043.2047.6052.1056.8061.6066.5071.6076.7082.0087.4092.9098.60110.0122.0135.0154.0188.0224.0

1000

23.5026.8030.2033.8037.4041.2045.2049.2053.4057.6062.0066.5071.1075.8080.6085.4095.50106.0117.0133.0163.0195.0

1100

20.6023.5026.5029.6032.9036.2039.6043.2046.8050.6054.4058.4062.4066.5070.7075.0083.8092.90102.0117.0143.0171.0

1200

18.3020.9023.5026.3029.1032.1035.2038.3041.5044.9048.3051.8055.3059.0062.7066.5074.3082.4090.80104.0127.080.00

1300

16.4018.7021.0023.5026.1028.7031.5034.3037.2040.1043.2046.3049.5052.8056.1059.5066.5073.8081.3092.9059.50

-

1400

13.8016.8019.0021.2023.5025.9028.4030.9033.5036.2039.0041.8044.6047.6050.6053.7060.0066.5073.3047.70

--

1500

14.4015.3017.2019.2021.3023.5025.8028.1030.4032.9035.4037.9040.5043.2045.9048.7054.4042.40

----

1600

12.2013.9015.7017.6019.5021.5023.5025.6027.8030.0032.3034.6037.0039.4041.3026.60

------

1700

11.2012.8014.4016.1017.0019.7021.6023.5025.5027.5029.6016.60

----------

1800

10.4011.8013.3014.9016.5018.2019.9011.30

--------------

1900

9.5910.9012.308.94

------------------

2000

----------------------

2200


Hileras 1234





DARIOlogo3

MacizoSolid



M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

Paso- Pitch 13/4" ASA 140 Rodillo - Roller 25,4 mm 44,45 mm BS 28 Rodillo - Roller 27,94 mm


9101112131415161718192021222324252627282930353840455057607695

129.96143.84157.77171.74185.74199.76213.79227.84241.91255.98270.06284.14298.24312.34326.44340.54354.65368.77382.88397.00411.12425.24495.88538.27566.54637.22707.91806.89849.32

1075.621344.39

148.80163.47178.05192.56207.01221.42235.79250.14264.46278.76293.04307.32321.58335.83350.07364.30378.53392.75406.96421.17435.38449.58520.55563.10591.46662.33733.18832.34874.83

1101.371370.32

88100112100110120120120130130130130130140140140140150150150150150160160160160175175175175190

88100112100110130130130160180200200200200200200200160160160160160160160160160175175175175190

88100112100110130130130160180200200200200200200200160160160160160160160160160175175175175190

60606060606060606060707070707070707070707070707070709090909090

100100100100100100100100100100100100100100100100100100100100100100120120120120130130130130130

150150150150150150150150150150150150150150150150150150150150150150150150150150150150150150150

Z

S D T S(1) D(2) T(2)


PASO/PitchASA140(1 3/4)

T22.7

N26.2

M271.6

M3 120.5

T123.5


PASO/Pitch28 - 1 3/4

T28.8

N30.8

M288.4

M3148

T128.8

(1) B.S. Largo Total ms 10 mm.(2) B.S. Largo Total ms 20 mm.

DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




DARIOlogo3

Potencia Engranajes para cadena paso 1 3/4" (ASA 140)Potencia Engranajes para cadena paso 1 3/4" (ASA 140)

11121314151617181920212223242526283032354045

Ndientes

Z

2.122.332.542.752.963.183.393.613.824.044.264.484.704.925.145.375.816.266.717.408.549.70

10

4.835.315.796.276.767.247.738.238.729.229.7210.2010.7011.2011.7012.2013.3014.3015.3016.9019.5022.10

25

9.029.9110.8011.7012.6013.5014.4015.4016.3017.2018.1019.1020.0020.9021.9022.8024.7026.7028.6031.5036.4041.30

50

16.8018.5020.2021.8023.5025.2026.9028.6030.4032.1033.8035.6037.3039.1040.8042.6046.2049.7053.3058.7067.9077.10

100

24.2026.6029.0031.5033.9036.3038.8041.3043.7046.2048.7051.3053.8056.3058.8061.4066.5071.6076.8084.6097.70111.0

150

31.4034.5037.6040.8043.9047.1050.3053.5056.7059.9063.1066.4069.7072.9076.2079.5086.2092.8099.50110.0127.0144.0

200

38.4042.2046.0049.8053.7057.5061.4065.3060.3073.2077.2081.2085.2089.2093.2097.20105.0113.0122.0134.0155.0176.0

250

45.2049.7054.2058.7063.2067.8072.4077.0081.6086.3091.0095.60100.0105.0110.0115.0124.0134.0143.0158.0182.0207.0

300

52.0057.1062.2067.4072.7077.9083.2088.5093.8099.10104.0110.0115.0121.0126.0132.0143.0154.0165.0181.0210.0238.0

350

58.6064.4070.2076.0081.9087.8093.8099.80106.0112.0118.0124.0130.0136.0142.0148.0161.0173.0186.0205.0236.0268.0

400

65.2071.6078.0084.5091.1097.70104.0111.0118.0124.0131.0138.0145.0151.0158.0165.0179.0193.0203.0227.0263.0298.0

450

71.6078.7085.8093.00100.0107.0115.0122.0129.0137.0144.0151.0159.0166.0174.0181.0197.0212.0227.0250.0289.0328.0

500

75.2085.7093.50101.0109.0117.0125.0133.0141.0149.0157.0165.0173.0181.0189.0198.0214.0231.0247.0272.0315.0357.0

550

66.0075.2084.8094.80100.5116.0127.0138.0150.0161.0170.0178.0187.0196.0205.0214.0232.0249.0267.0295.0340.0387.0

600

52.4059.7067.3075.2083.4091.90101.0110.0119.0128.0138.0148.0158.0169.0180.0190.0213.0236.0260.0297.0363.0434.0

700

42.9048.9055.1061.6068.3075.2082.4089.8097.40105.0113.0121.0130.0138.0147.0156.0174.0193.0213.0243.0297.0355.0

800

35.9041.0046.2051.6057.2063.1069.1075.2081.6088.1094.80102.0109.0116.0123.0131.0143.0162.0178.0204.0249.0297.0

900

30.7035.0039.4044.1048.9053.8059.0064.2069.7075.2080.9086.8092.8098.90105.0112.0125.0138.0152.0174.0213.0237.0

1000

26.6030.3034.2038.2042.4046.7051.1055.7050.4065.2070.2075.2080.4085.7091.1096.70108.0120.0132.0151.0178.092.70

1100

23.3026.6030.0033.5037.2041.0044.9048.9053.0057.2061.6066.0070.6075.2080.0084.8094.80105.0116.0130.0

--

1200

20.7023.6026.5029.7033.0036.3039.8043.3047.0050.8054.6058.6062.6066.7070.9075.2084.1093.20

----

1300

18.5021.1023.8026.6029.5032.5035.6038.8042.1045.4048.9052.4056.0059.7063.50

-------

1400

16.7019.0021.5024.0026.6029.3032.1035.0037.90

-------------

1500

15.2017.3019.5021.80

------------------

1600

----------------------

1700

Hileras 1234






DARIOlogo3

MacizoSolid



M3

B d A

C

B d A

M2

C

B d Ad A

T1 T

C

NT T TNT N T

Paso - Pitch 2" ASA 160 Rodillo - Roller 28,57 mm 50,8 mm BS 32 Rodillo - Roller 29,21 mm


9101112131415161718192021222324252627282930353840455057607695

148.53164.39180.31196.28212.27228.29244.33260.39276.46292.55308.64324.74340.84356.96373.07389.19405.32421.45437.58453.72469.85485.99566.72615.17647.47728.25809.04922.16970.65

1229.281536.44

170.05186.83203.49220.07236.58253.05269.48285.87302.24318.58334.91351.22367.52383.80400.08416.34432.60448.86465.10481.34497.58513.81594.91643.54675.96756.95837.92951.24999.80

1258.711566.08

92108140130130140140150150150150160160160170170170170170170170170170170170200200200230230230

92108140130140150150160180200200200200200200200200200200200200200200200200200230230250250250

92108140130140150150160180200200200200200200200200200200200200200200200200200230230250250250

7070708080808080808080808080808080909090909090909090

110110110110110

125125125125125125125125125125125125125125125125125140140140140140140140140140140140140160160

180180180180180180180180180180180180180180180180180195195195195195195195195195195195195200200

Z

S D T S D T


PASO/PitchASA160 (2)

T28.4

N30.1

M286.9

M3 145.4

T129


PASO/Pitch32 - 2

T28.8

N29.8

M287.4

M3146

T128.8

DimetroPrimitivo(d)

DimetroExterior(A)


TopDiameter(A)




DARIOlogo3

Potencia Engranajes para cadena paso 2" (ASA 160)Potencia Engranajes para cadena paso 2" (ASA 160)

11121314151617181920212223242526283032354045

Ndientes

Z

3.073.383.683.994.304.614.925.235.555.866.186.506.827.147.467.788.439.089.74

10.7012.4014.10

10

7.017.708.409.109.80

10.5011.2011.9012.7013.4014.1014.8015.6016.3017.0017.8019.2020.7022.2024.5028.3032.10

25

13.1014.4015.7017.0018.3019.6020.9022.3023.6025.0026.3027.7029.0030.4031.8033.1035.9038.7041.5045.7052.8059.90

50

24.4026.8029.2031.7034.1036.6039.1041.6044.1046.6049.1051.6054.2056.7059.3061.8067.0072.2077.4085.2098.50112.00

100

35.2038.6042.1045.6049.2052.7056.3059.9063.5067.1070.7074.4078.0081.7085.4089.1096.50104.00111.00123.00142.00161.00

150

45.6050.1054.6059.1063.7068.3072.9077.6082.2086.9091.6096.30101.00106.00111.00115.00125.00135.00144.00159.00184.00209.00

200

55.7061.2066.7072.3077.9083.5089.1094.80101.00106.00112.00118.00124.00129.00135.00141.00153.00165.00176.00194.00225.00255.00

250

65.6072.1078.6085.2091.7098.40105.00112.00118.00125.00132.00139.00146.00152.00159.00166.00180.00194.00208.00229.00265.00301.00

300

75.4082.8090.3097.80105.00113.00121.00128.00136.00144.00152.00159.00167.00175.00183.00191.00207.00223.00239.00263.00304.00345.00

350

85.0093.40102.0110.0119.0127.0136.0145.0153.0162.0171.0180.0189.0197.0206.0215.0233.0251.0269.0297.0343.0389.0

400

94.50104.0113.0123.0132.0142.0151.0161.0171.0180.0190.0200.0210.0220.0229.0239.0259.0279.0300.0330.0381.0433.0

450

96.60110.0124.0135.0145.0156.0166.0177.0188.0198.0209.0220.0231.0241.0252.0263.0285.0307.0329.0363.0419.0476.0

500

83.7095.40108.0120.0133.0147.0161.0175.0190.0205.0221.0237.0251.0263.0275.0287.0311.0335.0359.0395.0457.0519.0

550

73.5083.7094.40105.0117.0129.0141.0154.0167.0180.0195.0208.0222.0237.0252.0267.0298.0331.0365.0417.0494.0561.0

600

65.2074.2083.7093.60104.0114.0125.0136.0148.0160.0172.0184.0197.0210.0223.0237.0265.0293.0323.0370.0452.0538.0

650

58.3066.4074.9083.7092.80102.0112.0122.0132.0143.0154.0165.0176.0188.0200.0212.0237.0263.0289.0331.0404.0482.0

700

52.6059.9067.5075.5083.7092.20101.0110.0119.0129.0139.0149.0159.0169.0180.0191.0214.0237.0261.0298.0364.0418.0

750

47.7054.4061.3068.5076.0083.7091.7099.90108.0117.0126.0135.0144.0154.0164.0173.0194.0215.0237.0271.0331.0348.0

800

43.6049.6056.0062.6069.4076.4083.7091.2098.9093.10115.0123.0132.0140.0149.0159.0177.0196.0216.0247.0302.0271.0

850

40.0045.6051.4057.4063.7070.2075.8083.7090.8097.30105.0113.0121.0129.0137.0145.0162.0180.0198.0227.0257.0189.0

900

34.1038.9043.9049.0045.4059.9065.6071.5077.6072.6090.1096.60103.0110.0117.0124.0139.0154.0169.0180.0

--

1000

29.6033.7038.0042.5047.1051.9056.9062.0067.2063.7078.1083.7098.5095.40101.0108.0120.0

-----

1100

26.0029.6033.4037.3041.4045.6049.9054.4059.00

-68.50

-----------

1200

23.0026.3029.6033.10

------------------

1300

Hileras 1234






DARIOlogo3

Documents

Dimensiones de Catarinas