Detailed Product Description

Description/ApplicationStandard Made ToMaterial Size

Small calibration block for site checking of shear wave probes, time base and gain.1.5mmor5mmdiameter hole targetBS 2704IOW (Institute of Welding)Steel12.5x43x75mm

V2(Specify hole diameter)A4(BS)Small calibration block for site checking of shear wave probes, time base and gain. 1.5mm or 5mm diameter hole targetBS 2704IOW (Institute of Welding)Steel12.5x43x75mm

V2/20(Specify hole diameter)A4(BS)Generally as V2. Thicker block eliminates side wall echoes. 1.5mm or 5mm diameter hole target.BS 2704Steel20x43x75mm

AS2083 BLOCK 5 V2-25 ::

AS2083 BLOCK 5 V2-25V2 (A4) Calibration Block, 25mm, Carbon Steel25mm thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain.

Includes A 25mm and 50 mm radius, 1.5mm hole (or optional 5mm hole), Engraved reference mark scales from 35 to 75 degrees. In accordance with British Standard BS 2704 block A4, Fig. 4, and ISO 7963 Cal block No. 2, Fig. 1. Dimensions: 75mm x 43mm x 25mm Made from carbon steel. Fitted wooden storage case optionalAlso avaliable in 12.5mm and 20mm thicknesses for calibration of miniature probes or ranges less then 125mm. Aluminum Stainless Steel Titanium

AS2083 BLOCK 5 V2-20 ::

AS2083 BLOCK 5 V2-2020mm thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain.

Includes A 25mm and 50 mm radius, 1.5mm hole (or optional 5mm hole), Engraved reference mark scales from 35 to 75 degrees. In accordance with British Standard BS 2704 block A4, Fig. 4, and ISO 7963 Cal block No. 2, Fig. 1. Dimensions: 75mm x 43mm x 20mm Made from carbon steel. Come with hard canvas case..Also avaliable in 12.5mm and 25mm thicknesses. Aluminum Stainless Steel TitaniumAustralian Standard AS2083 6.1 DIMENSIONS.Calibration block No 5 shall conform to the dimensions shown in Fig. 6.1. Dimensional tolerances and material conditions shall be as specified in Section 1. The sides of the block shall be engraved at 5-degree intervals to permit beam angle measurement within the range 35 degrees to 70 degrees inclusive, relative to a 1.5 mm or a 5 mm diameter hole.When calibrating minature probes or when using test ranges less than 125 mm, a thinner block, e.g. 12.5 mm or 20 mm thick, may be used.NOTE: There is a difference of approximately 6 dB in reflectance between a 1.5 mm and a 5 mm diameter hole.

Product ID:V2A4.25.AV2 (A4) Calibration Block, 25mm, 7075-T6 Aluminum

25mm thick small calibration block for on-site checking of miniature shear wave probe index, time base, beam angle and gain. Includes a 25mm and 50 mm radius, 1.5mm hole (or 5mm), engraved reference markscalesfrom 35 to 75 degrees. In accordance with British Standard BS 2704 block A4, Fig. 4, and AS 2083. Dimensions: 75mm x 43mm x 25mm Made from aluminum. Also available in 12.5mm and 20mm thicknesses Fitted wooden storage case optional...see below.

Email FriendList Price:$361.00Price:$361.00

Product ID:V2A4.25.MA.SD16864V2/25mm (A4) Calibration Block, 7075-T6 Aluminum

1of 3

- V2/25mm Calibration Block

- Alloy: 7075-T6 Aluminum, anodized

- Condition: Laser engraving startedover the machine engravedtic marks. Stopped, but a line of laser still shows.

- 15% discount

- Serial No. 16864

Email FriendList Price:$361.00Price:$307.00