Embed Size (px)
Citation preview
SEE BEST PRACTICE RECOMMENDATIONS
Diamond TILE Blades DUT-HH
GLASS / REINFORCED PLASTIC
FIBREGLASS MARBLE - DRY CUTTING STEEL BARS, PIPE & SECTIONS SG & GREY IRON PORCELAIN & HARD TILES CERAMIC TILES INDIAN STONE GRANITE SLATE CLASS A ENGINEERING BRICKS CLAY PAVIORS / PIPES / TILES FLINT AGGREGATE PRODUCT CLASS B ENGINEERING BRICKS HEAVILY REINFORCED CONCRETE MEDIUM REINFORCED CONCRETE LIGHTLY REINFORCED CONCRETE CONCRETE HARD YORK STONE QUARTZITE LONDON BRICK HARD CONCRETE PRODUCTS KERBS / LINTELS / BEAMS CAST PIPES BRICKS / CONCRETE FLAGS HAND MADE BRICKS FACING BRICKS CONCRETE ROOF TILES SOFT CONCRETE PAVIORS SAND BASED PAVIORS GREEN CONCRETE CEMENT SCREED LIGHTWEIGHT CONCRETE BLOCK HOT ROLLED ASPHALT ABRASIVE SAND / GRITSTONE ASPHALT OVER CONCRETE ASPHALT ABRASIVE MORTAR
material type
POLYURETHANEHARD /DENSE
MATERIAL
SOFT / ABRASIVE MATERIAL
THE TOP-LINE FROM DURO, WHERE MAXIMUM PERFORMANCE IS THE ONLY CONSIDERATION DURING THE PRODUCT DESIGN PROCESS. THE VERY BEST QUALITY RAW MATERIALS ARE UTILISED TO ENSURE THE HIGHEST POSSIBLE OUTPUT.
ORDER LINE; 01909 552470 / 1 www.duro-diamonds.com www.YOKOTA..CO.UK
The blade for cutting hard tile
with hand held machinesfor the best finish & to minimise chipping in
external porcelain tile follow the guidelines here
HIGHLY SUITED
SUITABLE WITH RESERVATIONS
NOT SUITABLE
EXTERNAL PORCELAIN & HARD STONE TILES
DIMENSIONS DUT-HH
(9") 230 X 2.0 X 22.22 230DUT-HH £111.08
(12") 300 X 2.4 X 20.00 300DUT-HH £177.71
DUT-HH external pORCELAIN TILes
EXCELLENT SPEED OF CUT
HOT PRESSED 10MM SEGMENT HEIGHT
HIGH DENSITY/DIAMOND CONCENTRATION
LASER CUT TENSION REDUCING SLOTS
FOR HAND HELD MACHINES
DESCRIPTION ; For angle grinders, petrol saws and other hand held power tools to cut external porcelain (grade 5), ceramic, natural stone and other very hard tiles. Use of water is recommended (Do Not Use Water With Electric Angle Grinders).
• DRY OR WET CUTTING (DO NOT USE WATER WITH HAND HELD ELECTRIC ANGLE GRINDERS)
• CUT IN ONE SINGLE PASS• DO NOT USE IN A RECIPROCATING MOTION• SECURE TO A SUITABLE FLAT SURFACE TO REDUCE
VIBRATION
- A WOODEN PALLET IS RECOMMENDED- SECURE THE TILE ON THE PALLET SO THAT THERE IS
NO TILE OVERHANGING- CUT THROUGH THE TILE FULLY IN ONE SLOW PASS- CUTTING INTO THE PALLET WILL HAVE NO
DETRIMENTAL EFFECT ON THE BLADE- THIS WILL PREVENT BREAKING OF THE TILE DURING
THE CUTTING PROCESS
![B C&% % 1 % 8 : G ':&% I G J & D %7L% . 3 · [ $3 hh hh$#hh 1 [hhh hh hh dhhphh #hhm#hhbhh hh&lhh < w) d?. {lhh hh$ @b#-p 3 c 3:;hhh $# #" )j p d] #hhm#hhbhh hh&x %hh | x4 3 hh?hh](https://img.dokumen.tips/doc/110x75/5ea61d5cbec94348cc54f9a5/b-c-1-8-g-i-g-j-d-7l-3-3-hh-hhhh-1-hhh-hh-hh.jpg)
