16
036-21023-002 Rev A (5/00) FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE 16 SEER 2-5 TON AIR CONDITIONING SPLIT-SYSTEM COOLING TECHNICAL GUIDE TECHNICAL GUIDE ® MODELS: H4TS024 H4TS030 H4TS036 H4TS048 H4TS060 DESCRIPTION The HTS Stealth series condensing units use Twin Single compressor technology to provide cooling efficiencies up to 16.7 SEER. They are to be installed with the matching variable speed Enhancer air handler or Dia- mond furnace, or with a two-stage or single-stage indoor unit, a corre- sponding coil and sweat connect lines. A factory specified balanced port hard shut-off TXV kit must be used for proper installation and optimum performance. These units are backed by a 10 - year limited warranty on the compressor and 1 - year on all other parts. FEATURES QUALITY CONDENSER COILS - The coil is constructed of copper tube and hardened aluminum fins for durability and long lasting efficient opera- tion. The fins on the unit are protected with a decorative grille. DURABLE FINISH - Cabinet is made of powder painted steel over pre- painted primer. The pre-treated flat galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and glossy earth tone finish insure less fading when exposed to sunlight. This finish has been tested to provide 1/3 greater protection than conventional units. PROTECTED COMPRESSORS - The Twin Single compressor is pro- tected against high and low pressure. Hard start components are included to ensure start-up under adverse conditions. All models have standard crankcase heat for added protection. OPTIMUM PERFORMANCE - The solid-state electronic controlboard optimizes the compressor staging based on load requirements, provides a 5-minute anti-short cycle timer for each compressor, and simplifies trou- bleshooting with built in self diagnostics. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. All units contain enough refrig- erant for the smallest matching indoor coil and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. EFFECTIVE HUMIDITY CONTROL - The inherent design of the Stealth system and the staging operation of the Twin Single compressor provide effective humidity control at the lowest possible operating cost. An optional dehumidification control accessory is available to maintain the humidity at a set desired level. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact loca- tion on multi-unit applications. LOW OPERATING SOUND LEVEL - The upward air flow carries the nor- mal operating noise up away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and com- pressor operating sounds. LOW MAINTENANCE - Long life permanently lubricated motor- bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections and a single panel covering the electrical controls make servicing easy. Easy access for coil clearing is also provided. RE-USABLE SERVICE VALVES - Provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

DESCRIPTION - Johnson Supplyjohnsonsupply.com/york2001/PUB/55037/OUT/Tg4y.pdfThe HTS Stealth series condensing units use Twin Single compressor technology to provide cooling efficiencies

Embed Size (px)

Citation preview

036-21023-002 Rev A (5/00)

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

16 SEER 2-5 TON

AIR CONDITIONING

SPLIT-SYSTEM COOLING

TECHNICALGUIDE TECHNICALGUIDE

��

MODELS: H4TS024H4TS030H4TS036H4TS048H4TS060

DESCRIPTIONThe HTS Stealth series condensing units use Twin Single compressor technology to provide cooling efficiencies up to 16.7 SEER. They are to be installed with the matching variable speed Enhancer air handler or Dia-mond furnace, or with a two-stage or single-stage indoor unit, a corre-sponding coil and sweat connect lines. A factory specified balanced port hard shut-off TXV kit must be used for proper installation and optimum performance. These units are backed by a 10 - year limited warranty on the compressor and 1 - year on all other parts.

FEATURESQUALITY CONDENSER COILS - The coil is constructed of copper tube and hardened aluminum fins for durability and long lasting efficient opera-tion. The fins on the unit are protected with a decorative grille.

DURABLE FINISH - Cabinet is made of powder painted steel over pre-painted primer. The pre-treated flat galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and glossy earth tone finish insure less fading when exposed to sunlight. This finish has been tested to provide 1/3 greater protection than conventional units.

PROTECTED COMPRESSORS - The Twin Single compressor is pro-tected against high and low pressure. Hard start components are included to ensure start-up under adverse conditions. All models have standard crankcase heat for added protection.

OPTIMUM PERFORMANCE - The solid-state electronic controlboard optimizes the compressor staging based on load requirements, provides a 5-minute anti-short cycle timer for each compressor, and simplifies trou-bleshooting with built in self diagnostics.

LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. All units contain enough refrig-erant for the smallest matching indoor coil and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof.

EFFECTIVE HUMIDITY CONTROL - The inherent design of the Stealth system and the staging operation of the Twin Single compressor provide effective humidity control at the lowest possible operating cost. An optional dehumidification control accessory is available to maintain the humidity at a set desired level.

TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact loca-tion on multi-unit applications.

LOW OPERATING SOUND LEVEL - The upward air flow carries the nor-mal operating noise up away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and com-pressor operating sounds.

LOW MAINTENANCE - Long life permanently lubricated motor- bearings need no annual servicing.

EASY SERVICE ACCESS - Fully exposed refrigerant connections and a single panel covering the electrical controls make servicing easy. Easy access for coil clearing is also provided.

RE-USABLE SERVICE VALVES - Provided on both the liquid and vapor sweat connections for ease of evacuating and charging.

036-21023-002 Rev. A (5/00)

2 Unitary Products Group

Table 1: COOLING CAPACITY - Variable Speed Air Handler

UNIT MODEL

VAR SPEED AIR HANDLER

COIL MODEL

COOLING

MODEL ELEC. HEAT KW W STAGE RATED

CFM

CAP SYSTEMKW EER1 SEER

TOTAL SENS.

H4TS024 N+VSB12 5,7.5,10,15,18 17

G+FD024S17 1 600 12.4 10.0 0.92 13.5

15.52 820 24.0 16.8 2.00 12.0

G+FD030S17 1 600 12.8 10.2 0.91 14.0

16.02 820 24.6 17.2 1.97 12.5

G+FD036S17 1 600 13.0 10.4 0.91 14.3

16.22 820 25.0 17.5 2.00 12.5

H4TS030

N-VSB12 5,7.5,10,15,18 17

G+FD030S171 670 15.0 12.0 1.09 13.7

15.52 1035 30.0 21.6 2.59 11.6

G+FD036S171 670 15.4 12.2 1.12 13.7

16.02 1035 31.0 22.0 2.67 11.6

N-VSC16 5,7.5,10,15,20 21 G+FD042S211 690 16.4 13.4 1.14 14.4

16.02 1065 31.6 23.4 2.68 11.8

H4TS036 N-VSC16 5,7.5,10,15,20 21

G+FD036S211 770 20.0 16.0 1.46 13.7

15.52 1185 35.0 26.0 2.97 11.8

G+FD042S211 770 20.0 16.0 1.46 13.7

15.52 1185 35.0 26.0 2.97 11.8

G+FD048S211 770 20.6 16.6 1.43 14.4

16.02 1185 36.0 26.6 2.88 12.5

H4TS048

N-VSC16 5, 7.5,10,15,20 21 G+FD048S21

1 1050 25.0 20.0 1.72 14.516.0

2 1605 49.0 36.0 4.45 11.0

N-VSD20 5, 7.5,10,15,20 24

G+FD048S241 1050 25.0 20.0 1.72 14.5

16.02 1570 49.0 36.0 4.45 11.0

G+FD060S241 1050 25.0 21.0 1.79 14.0

16.02 1570 50.0 37.5 4.46 11.2

H4TS060 N-VSD20 5, 7.5,10,15,20 24

G+FD060S241 1250 33.0 26.4 2.44 13.5

15.02 1900 59.0 43.0 5.67 10.4

G+FD061H241 1250 33.0 26.4 2.36 14.0

15.52 1900 59.5 44.0 5.56 10.7

1. See notes on page 5.

SOUND RATINGS

SOUND RATINGSUNIT MODEL SOUND RATING

DECIBELS

H4TS 024 72

H4TS 030 72

H4TS 036 74

H4TS 048 78

H4TS 060 78

036-21023-002 Rev. A (5/00)

Unitary Products Group 3

Table 2: COOLING CAPACITY - Single Speed Furnace

UNIT MODEL

SINGLE SPEED FURNACE

COIL MODEL

COOLING

NOMINAL AIRFLOW W STAGE RATED

CFM

CAP SYSTEMKW EER1 SEER

TOTAL SENS.

H4TS024

--

--

--

--

--

80010001200

14,17G+UA036S14,16,21

1 600 12.0 10.0 0.95 12.613.6

21 2 800 24.0 17.2 2.26 10.6

17 G+UA048S171 600 12.4 10.4 0.95 13.0

14.02 800 24.4 17.6 2.22 11.0

-- G+HD0361 600 12.2 10.2 0.97 12.6

13.62 800 24.4 17.6 2.30 10.6

17 G+FD030S171 600 12.2 10.2 0.97 12.6

13.52 800 24.0 17.2 2.26 10.6

17 G+FD036S171 600 12.4 10.4 0.98 12.6

13.62 800 24.4 17.6 2.22 11.0

H4TS030

--

--

--

--

--

--

100012001400

17,21 G-UA048S17,211 650 15.4 13.4 1.22 12.6

14.02 1000 32.0 23.6 2.91 11.0

-- G1HD0361 650 15.0 12.2 1.27 11.8

13.02 1000 30.0 22.0 2.94 10.2

-- G1HD0481 650 15.4 13.4 1.22 12.6

14.02 1000 32.0 23.6 2.91 11.0

17 G+FD036S171 650 15.0 12.2 1.27 11.8

13.02 1000 30.0 22.0 2.94 10.2

21 G+FD042S211 650 15.2 13.4 1.27 12.0

13.52 1000 30.6 23.4 2.89 10.6

17 G+FD046S171 650 15.0 12.2 1.27 11.8

13.02 1000 30.0 22.0 2.94 10.2

H4TS036

--

--

--

--

--

--

120014001600

-- G+HD0481 750 20.0 16.6 1.67 12.0

13.52 1200 35.0 26.6 3.18 11.0

17,21 G+UA048S17,211 750 19.2 16.6 1.60 12.0

13.52 1200 35.0 26.6 3.18 11.0

17,21 G+FD036S17,211 750 19.2 16.0 1.66 11.6

13.02 1200 34.0 26.0 3.27 10.4

21 G+FD042S211 750 19.2 16.0 1.66 11.6

13.02 1200 34.0 26.0 3.27 10.4

17 G+FD046S171 750 19.2 16.0 1.66 11.6

13.02 1200 34.0 26.0 3.27 10.4

21,24 G-FD048S21,241 750 20.0 16.6 1.67 12.0

13.52 1200 35.0 26.6 3.13 11.2

H4TS048

--

--

--

--

--

16002000

-- G+HD0601 1050 24.4 20.0 2.00 12.2

14.02 1600 49.0 37.5 4.67 10.5

21 G+UA048S211 1050 24.4 20.0 2.00 12.2

14.02 1600 48.0 36.0 4.71 10.2

21,24 G+UA060S21,241 1050 24.0 20.0 1.97 12.2

14.02 1600 48.0 36.0 4.71 10.2

21,24 G+FD048S21,241 1050 24.0 20.0 1.97 12.2

14.02 1600 48.0 36.0 4.71 10.2

24 G+FD060S241 1050 24.4 21.0 2.00 12.2

14.02 1600 49.0 37.5 4.67 10.5

H4TS060

--

--

--

--

2000

-- G+HD0601 1250 32.0 26.4 2.67 12.0

13.52 1900 58.0 43.0 5.69 10.2

21,24 G+UA060S21,241 1250 32.0 26.4 2.67 12.0

13.52 1900 58.0 43.0 5.69 10.2

24 G+FD060S241 1250 32.0 26.4 2.67 12.0

13.52 1900 58.0 43.0 5.69 10.2

24 G+FD061H241 1250 32.4 26.4 2.70 12.0

13.52 1900 58.5 44.0 5.74 10.2

1. See notes on page 5.

036-21023-002 Rev. A (5/00)

4 Unitary Products Group

Table 3: COOLING CAPACITY - Variable Speed Furnace

UNIT MODEL

VARIABLE SPEED FURNACE MODEL W COIL MODEL1

COOLING2

STAGE RATEDCFM

CAP SYSTEMKW EER3 SEER

TOTAL SENS.

H4TS024

P1XUB12V055 17

G+UA036S171 600 12.6 10.2 0.92 13.7

15.52 820 24.4 17.2 2.09 11.7

G+FD024S171 600 12.4 10.2 0.95 13.0

15.02 820 23.8 16.8 2.07 11.5

G+FD030S171 600 12.6 10.2 0.93 13.5

15.52 820 24.4 17.2 2.10 11.6

G-FD036S171 600 12.8 10.2 0.93 13.7

15.52 820 25.0 17.4 2.14 11.7

G+FD046S171 600 12.8 10.4 0.93 13.7

15.52 820 25.0 17.4 2.14 11.7

P1DUA12V064 14

G+UA030S141 600 12.4 10.0 0.95 13.0

15.02 820 23.8 16.8 2.11 11.3

G+UA036S14 1 600 12.6 10.2 0.92 13.7

15.52 820 24.4 17.2 2.09 11.7

H4TS030

P1XUB12V055 17

G1UA036S171 670 15.4 13.4 1.18 13.0

14.52 1035 29.8 21.6 2.68 11.1

G1UA048S171 670 15.0 12.2 1.13 13.3

15.02 1035 29.6 21.6 2.62 11.3

G2FD030S171 670 15.4 12.2 1.18 13.0

14.52 1035 29.8 21.6 2.71 11.0

G2FD036S171 670 15.0 12.0 1.15 13.0

14.52 1035 29.6 21.6 2.69 11.0

G2FD046S171 670 15.0 12.0 1.15 13.0

14.52 1035 29.6 21.6 2.69 11.0

P1XUC16V075 21

G1UA036S211 690 15.0 12.0 1.15 13.0

14.52 1065 29.6 21.6 2.69 11.0

G1UA048S211 690 15.4 12.2 1.18 13.0

14.52 1065 29.4 21.4 2.67 11.0

G2FD036S211 670 15.4 12.2 1.18 13.0

14.52 1065 29.4 21.4 2.67 11.0

G2FD042S211 690 16.0 13.0 1.15 13.9

15.52 1065 31.4 23.0 2.75 11.4

G2FD048S211 690 16.0 13.0 1.15 13.9

15.52 1065 31.4 23.0 2.75 11.4

P1DUA12V064 17 G1UA036S141 670 15.4 12.2 1.19 13.0

14.52 1035 30.2 22.0 2.75 11.0

P1DUB16V080 17

G1UA036S171 670 15.4 12.2 1.18 13.0

14.52 1035 29.8 21.6 2.71 11.0

G1UA048S171 670 15.0 12.0 1.13 13.3

15.02 1035 29.6 21.6 2.64 11.2

G2FD030S171 670 15.0 12.0 1.15 13.0

14.52 1035 29.8 21.6 2.71 11.0

G2FD036S171 670 15.0 12.0 1.14 13.2

15.02 1035 29.6 21.6 2.69 11.0

G2FD046S171 670 15.0 12.0 1.14 13.2

15.02 1035 29.6 21.6 2.64 11.2

036-21023-002 Rev. A (5/00)

Unitary Products Group 5

H4TS036

P1XUB12V055 P1DUB16V080

1717

G1UA048S17 1 750 20.0 16.0 1.49 13.4

15.02 1150 34.8 26.0 3.08 11.3

G2FD036S17 1 750 20.0 16.0 1.49 13.4

15.02 1150 34.8 26.0 3.08 11.3

G2FD046S17 1 750 20.0 16.0 1.49 13.4

15.02 1150 34.8 26.0 3.08 11.3

P1XUC16V075 21

G1UA048S21 1 770 21.0 16.6 1.49 14.1

15.02 1185 36.8 27.0 3.17 11.6

G2FD036S21 1 770 20.4 16.0 1.50 13.6

15.02 1185 35.4 26.0 3.11 11.4

G2FD042S21 1 770 20.4 16.0 1.50 13.6

15.02 1185 35.4 26.0 3.11 11.4

G2FD048S21 1 770 21.0 16.6 1.49 14.1

15.52 1185 36.8 27.0 3.17 11.6

P1XUC20V095 P1DUC20V096 21

G1UA048S21 1 770 21.0 16.0 1.47 14.3

15.52 1200 37.0 27.0 3.19 11.6

G2FD036S21 1 770 20.4 16.4 1.49 13.7

15.02 1200 35.4 26.0 3.11 11.4

G2FD042S21 1 770 20.4 16.4 1.49 13.7

15.02 1200 35.4 26.0 3.11 11.4

G2FD048S21 1 770 21.0 16.6 1.48 14.2

15.52 1200 37.0 27.0 3.19 11.6

P1XUD20V112 24 G2FD048S24 1 770 21.0 16.6 1.48 14.2

15.52 1200 37.0 27.0 3.19 11.6

H4TS048

P1XUC16V075P1XUC20V095P1DUC20V096

21

G-UA048S211 1050 25.0 1.75 14.3

15.52 1600 49.0 36.0 4.54 10.8

G-UA060S211 1050 26.0 21.0 1.82 14.3

15.52 1600 51.0 37.5 4.72 10.8

G-FD048S211 1050 25.0 20.0 1.75 14.3

15.52 1600 49.0 36.0 4.54 10.8

P1XUD20V112 24

G-FD048S241 1050 25.0 20.0 1.75 14.3

15.52 1600 49.0 36.0 4.54 10.8

G-UA060S241 1050 26.0 21.0 1.82 14.3

15.52 1600 51.0 37.5 4.72 10.8

G-FD060S241 1050 26.0 21.0 1.82 14.3

15.52 1600 51.0 37.5 4.72 10.8

H4TS060

P1XUC20V095P1DUC20V096 21 G-UA060S21

1 1250 33.0 26.4 2.52 13.114.5

2 1900 59.0 43.0 5.67 10.4

P1XUD20V112 24

G-UA060S241 1250 33.0 26.4 2.52 13.1

14.52 1900 59.0 43.0 5.67 10.4

G-FD060S241 1250 33.0 26.4 2.52 13.1

14.52 1900 59.0 43.0 5.67 10.4

G-FD061H241 1250 34.0 27.0 2.54 13.4

15.02 1900 60.0 44.0 5.66 10.6

1. Refer to coil installation guide for proper coil application.2. Standard cooling operation is limited to 45°F outdoor ambient.3. EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at a 95°F outdoor ambient divided by the total electric power in

watt-hours at those conditions.

Certified in accordance with the Unitary Small Equipment certification program which is based on ARI Standard 210/240 MBH based on 80°F entering air temperature, 50% RH, and rated air flow KW includes compressor, outdoor fan and indoor blower motor watts. Add-on coils include 365 watts/1000 CFM for blowr motor.

Table 3: COOLING CAPACITY - Variable Speed Furnace (Continued)

UNIT MODEL

VARIABLE SPEED FURNACE MODEL W COIL MODEL1

COOLING2

STAGE RATEDCFM

CAP SYSTEMKW EER3 SEER

TOTAL SENS.

036-21023-002 Rev. A (5/00)

6 Unitary Products Group

Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder1

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

H4TS024 / G+FD024S14, 17

600

85/72 14.9 10.1 0.69 14.3 10.0 0.77 13.5 9.70 0.85 12.7 9.40 0.93 11.9 9.20 1.00

80/67 13.7 10.2 0.69 13.0 9.90 0.77 12.3 9.60 0.84 11.6 9.30 0.91 10.8 9.00 0.98

75/62* 12.4 10.1 0.69 11.8 9.80 0.76 11.3 9.60 0.83 10.7 9.10 0.90 10.0 8.60 0.96

70/57 11.5 9.80 0.69 10.9 9.30 0.76 10.4 8.90 0.82 9.80 8.40 0.89 9.20 7.90 0.95

650

85/72 15.2 10.7 0.69 14.4 10.4 0.77 13.6 10.1 0.85 12.8 9.90 0.93 12.0 9.60 1.00

80/67 13.8 10.6 0.69 13.8 10.3 0.77 12.4 10.0 0.84 11.7 9.70 0.91 11.1 9.40 0.98

75/62* 12.5 10.5 0.69 12.1 10.3 0.76 11.4 9.80 0.83 10.8 9.30 0.90 10.2 8.70 0.97

70/57 11.7 10.0 0.69 11.1 9.50 0.76 10.5 9.00 0.82 9.90 8.50 0.89 9.30 8.00 0.95

700

85/72 15.3 11.1 0.69 14.5 10.8 0.77 13.7 10.5 0.85 12.9 10.3 0.93 12.0 10.0 1.00

80/67 13.9 11.0 0.69 13.2 10.7 0.76 12.5 10.4 0.84 11.9 10.2 0.92 11.2 9.60 0.99

75/62* 12.8 11.0 0.69 12.2 10.4 0.76 11.6 9.90 0.83 10.9 9.40 0.90 10.3 8.80 0.97

70/57 11.8 10.1 0.69 11.2 9.60 0.76 10.6 9.10 0.83 10.0 8.60 0.89 9.40 8.00 0.95

H4TS024 / G+FD030S17

600

85/72 15.4 10.3 0.68 14.7 10.2 0.76 13.9 9.90 0.84 13.1 9.60 0.92 12.3 9.30 0.99

80/67 14.2 10.3 0.68 13.4 10.1 0.75 12.7 9.80 0.83 11.9 9.50 0.90 11.2 9.20 0.97

75/62* 12.9 10.3 0.68 12.2 10.0 0.75 11.7 9.80 0.82 11.0 9.30 0.89 10.4 8.70 0.95

70/57 11.9 10.0 0.68 11.3 9.50 0.75 10.7 9.00 0.81 10.1 8.50 0.88 9.50 8.00 0.94

650

85/72 15.6 10.9 0.68 14.8 10.6 0.76 14.0 10.3 0.84 13.2 10.0 0.92 12.3 9.70 0.99

80/67 14.3 10.8 0.68 13.6 10.5 0.75 12.8 10.2 0.83 12.0 9.90 0.90 11.4 9.60 0.97

75/62* 13.0 10.7 0.68 12.4 10.5 0.75 11.8 10.0 0.82 11.2 9.40 0.89 10.5 8.80 0.95

70/57 12.1 10.2 0.68 11.5 9.70 0.75 10.9 9.20 0.81 10.3 8.80 0.88 9.60 8.10 0.94

700

85/72 15.7 11.3 0.68 14.9 11.0 0.76 14.1 10.7 0.84 13.3 10.5 0.92 12.4 10.2 0.99

80/67 14.4 11.2 0.67 13.6 10.9 0.75 12.9 10.6 0.83 12.3 10.3 0.90 11.5 9.7 0.98

75/62* 13.3 11.2 0.68 12.6 10.6 0.75 12.0 10.1 0.82 11.3 9.50 0.89 10.6 8.90 0.96

70/57 12.2 10.3 0.68 11.6 9.8 0.75 11.0 9.3 0.81 10.4 8.70 0.88 9.70 8.20 0.94

H4TS024 / G+FD036S17

036-21023-002 Rev. A (5/00)

Unitary Products Group 7

600

85/72 15.7 10.4 0.69 14.8 10.2 0.77 14.1 10.0 0.86 13.3 9.80 0.94 12.4 9.50 1.01

80/67 14.4 10.5 0.69 13.7 10.2 0.77 12.9 9.90 0.85 12.1 9.70 0.92 11.3 9.40 0.99

75/62* 13.1 10.5 0.69 12.4 10.2 0.77 11.8 9.90 0.84 11.2 9.40 0.91 10.5 8.80 0.97

70/57 12.1 10.1 0.69 11.5 9.60 0.76 10.9 9.10 0.83 10.3 8.60 0.89 9.70 8.10 0.96

650

85/72 15.9 11.0 0.69 15.1 10.8 0.78 14.2 10.5 0.86 13.4 10.2 0.94 12.5 9.90 1.01

80/67 14.5 10.9 0.69 13.8 10.7 0.77 13.0 10.4 0.85 12.2 10.1 0.92 11.6 9.70 0.99

75/62* 13.3 11.1 0.69 12.7 10.6 0.77 12.0 10.1 0.84 11.4 9.50 0.91 10.7 8.90 0.98

70/57 12.3 10.3 0.69 11.7 9.80 0.76 11.1 9.30 0.83 10.4 8.70 0.90 9.80 8.20 0.96

700

85/72 16.0 11.5 0.69 15.2 11.2 0.78 14.3 11.0 0.86 13.4 10.7 0.94 12.6 10.4 1.01

80/67 14.6 11.4 0.69 13.9 11.1 0.77 13.2 11.0 0.85 12.4 10.4 0.92 11.7 9.80 1.00

75/62* 13.5 11.3 0.69 12.8 10.7 0.76 12.2 10.2 0.84 11.5 9.60 0.91 10.8 9.00 0.98

70/57 12.4 10.4 0.69 11.8 9.90 0.76 11.2 9.4 0.83 10.6 8.80 0.90 9.90 8.30 0.96

H4TS030 / G+FD030S17

650

85/72 18.2 12.3 0.87 17.3 12.0 0.97 16.3 11.7 1.07 15.4 11.4 1.16 14.4 11.0 1.25

80/67 16.7 12.2 0.87 15.8 11.9 0.97 14.9 11.5 1.06 14.0 11.2 1.14 13.3 10.9 1.23

75/62* 15.1 12.1 0.87 14.5 11.9 0.96 13.8 11.3 1.05 13.0 10.6 1.13 12.2 10.0 1.21

70/57 14.1 11.5 0.87 13.4 10.9 0.96 12.7 10.4 1.04 11.9 9.80 1.12 11.2 9.20 1.19

700

85/72 18.3 12.8 0.87 17.4 12.5 0.98 16.4 12.2 1.07 15.4 11.8 1.17 14.4 11.5 1.26

80/67 16.8 12.7 0.87 15.9 12.3 0.97 15.0 12.0 1.06 14.3 11.7 1.15 13.4 11.0 1.24

75/62* 15.4 12.6 0.87 14.7 12.0 0.96 14.0 11.4 1.05 13.2 10.8 1.14 12.4 10.1 1.22

70/57 14.2 11.6 0.88 13.5 11.1 0.96 12.8 10.5 1.04 12.1 9.90 1.12 11.3 9.30 1.19

800

85/72 18.5 13.7 0.88 17.6 13.4 0.98 16.6 13.1 1.08 15.7 12.9 1.18 14.8 12.1 1.27

80/67 16.9 13.6 0.88 16.3 13.3 0.98 15.4 12.6 1.07 14.6 11.9 1.16 13.7 11.2 1.25

75/62* 15.8 12.9 0.88 15.0 12.3 0.97 14.2 11.6 1.06 13.4 11.0 1.14 12.6 10.1 1.22

70/57 14.6 11.9 0.88 13.8 11.3 0.97 13.1 10.7 1.05 12.3 10.0 1.13 11.5 9.4 1.21

H4TS030 / G+FD036S21

650

85/72 18.5 12.4 0.88 17.6 12.1 0.98 16.6 11.9 1.08 15.7 11.6 1.17 14.8 11.3 1.27

80/67 17.0 12.4 0.88 16.2 12.1 0.98 15.3 11.8 1.07 14.4 11.4 1.16 13.6 10.9 1.24

75/62* 15.6 12.3 0.88 14.9 11.9 0.97 14.1 11.3 1.06 13.4 10.7 1.14 12.6 10.1 1.22

70/57 14.4 11.6 0.88 13.8 11.0 0.97 13.0 10.5 1.05 12.3 9.90 1.13 11.6 9.30 1.20

700

85/72 18.6 13.0 0.89 17.6 12.7 0.99 16.8 12.5 1.08 15.8 12.1 1.18 14.8 11.7 1.27

80/67 17.1 12.9 0.88 16.3 12.6 0.98 15.4 12.2 1.07 14.6 11.7 1.16 13.8 11.0 1.25

75/62* 15.8 12.7 0.89 15.1 12.1 0.98 14.3 11.5 1.06 13.5 10.8 1.15 12.7 10.2 1.23

70/57 14.6 11.7 0.89 13.9 11.2 0.97 13.2 10.6 1.05 12.4 10.1 1.13 11.7 9.30 1.21

800

85/72 18.9 14.0 0.89 17.9 13.7 0.99 16.9 13.3 1.09 16.1 12.9 1.19 15.1 12.1 1.29

80/67 17.4 13.8 0.89 16.6 13.3 0.99 15.8 12.6 1.08 14.9 11.9 1.17 14.0 11.2 1.26

75/62* 16.1 13.0 0.89 15.4 12.3 0.98 14.6 11.7 1.07 13.7 11.0 1.16 12.9 10.3 1.24

70/57 14.9 12.0 0.89 14.2 11.4 0.98 13.4 10.7 1.06 12.6 10.1 1.14 11.8 9.50 1.22

H4TS030 / G+FD042S21

650

85/72 19.8 13.6 0.90 18.7 13.3 1.01 17.7 13.0 1.11 16.7 12.7 1.21 15.7 12.4 1.30

80/67 18.1 13.6 0.90 17.2 13.3 1.00 16.3 12.9 1.10 15.3 12.5 1.19 14.5 12.0 1.27

75/62* 16.6 13.5 0.90 15.8 13.1 1.00 15.0 12.4 1.09 14.2 11.7 1.17 13.4 11.0 1.25

70/57 15.4 12.7 0.91 14.6 12.1 0.99 13.9 11.5 1.08 13.1 10.8 1.16 12.3 10.2 1.23

700

85/72 19.9 14.2 0.91 18.8 13.9 1.01 17.9 13.7 1.11 16.8 13.2 1.21 15.8 12.8 1.30

80/67 18.5 14.1 0.91 17.3 13.7 1.00 16.4 13.4 1.10 15.6 12.9 1.19 14.6 12.1 1.28

75/62* 16.8 13.9 0.91 16.0 13.3 1.00 15.2 12.6 1.09 14.4 11.9 1.18 13.5 11.2 1.26

70/57 15.6 12.9 0.91 14.8 12.2 1.00 14.0 11.6 1.08 13.2 10.9 1.16 12.4 10.2 1.24

Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder1 (Continued)

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

036-21023-002 Rev. A (5/00)

8 Unitary Products Group

800

85/72 20.1 15.4 0.91 19.1 15.0 1.02 18.0 14.6 1.12 17.1 14.1 1.22 16.1 13.3 1.32

80/67 18.5 15.1 0.91 17.7 14.6 1.01 16.8 13.9 1.11 15.8 13.1 1.20 14.9 12.3 1.30

75/62* 17.2 14.2 0.91 16.4 13.5 1.01 15.5 12.8 1.10 14.6 12.1 1.19 13.7 11.3 1.27

70/57 15.9 13.1 0.91 15.1 12.5 1.00 14.3 11.8 1.09 13.4 11.1 1.17 12.6 10.4 1.25

H4TS036 / G+FD036S21

700

85/72 23.2 15.1 1.17 22.7 15.4 1.27 21.7 15.5 1.38 20.6 15.2 1.50 19.3 14.8 1.62

80/67 21.1 15.0 1.19 20.8 15.5 1.29 19.9 15.4 1.39 18.7 15.2 1.51 17.5 14.7 1.62

75/62* 19.2 15.2 1.20 18.8 15.5 1.29 17.9 15.5 1.40 16.9 15.2 1.50 15.9 14.7 1.61

70/57 17.3 15.1 1.21 17.0 15.5 1.29 16.3 15.3 1.39 15.5 14.8 1.49 14.6 13.9 1.59

750

85/72 23.4 15.5 1.17 22.8 16.0 1.27 21.9 16.1 1.38 20.7 15.9 1.50 19.4 15.5 1.63

80/67 21.4 15.6 1.19 20.9 16.0 1.29 20.0 16.0 1.39 18.9 15.8 1.51 17.6 15.4 1.62

75/62* 19.4 15.7 1.20 18.9 16.0 1.29 18.1 16.1 1.40 17.1 15.8 1.50 16.1 15.3 1.61

70/57 17.5 15.7 1.21 17.2 15.9 1.30 16.6 15.8 1.39 15.7 15.0 1.50 14.8 14.1 1.60

850

85/72 23.7 16.4 1.16 23.2 17.2 1.26 22.2 17.3 .38 20.9 17.1 1.50 19.6 16.7 1.63

80/67 21.8 16.6 1.19 21.2 17.0 1.28 20.2 17.1 1.39 19.1 17.0 1.51 17.9 16.5 1.63

75/62* 19.7 16.6 1.20 19.2 17.1 1.30 18.4 17.2 1.40 17.5 16.7 1.51 16.5 15.7 1.62

70/57 18.0 16.5 1.21 17.7 16.9 1.30 17.0 16.2 1.40 16.2 15.4 1.50 15.2 14.5 1.61

H4TS036 / G+FD042S21

700

85/72 23.4 15.2 1.17 22.8 15.5 1.27 21.7 15.4 1.38 20.6 15.3 1.50 19.3 14.8 1.62

80/67 21.3 15.1 1.19 20.7 15.4 1.29 19.9 15.4 1.39 18.7 15.1 1.51 17.5 14.7 1.62

75/62* 19.4 15.3 1.20 18.8 15.6 1.29 17.9 15.5 1.40 16.9 15.2 1.50 15.9 14.7 1.61

70/57 17.4 15.2 1.21 17.1 15.5 1.29 16.3 15.3 1.39 15.5 14.8 1.49 14.6 13.9 1.59

750

85/72 23.6 15.6 1.16 22.9 16.0 1.27 21.9 16.1 1.38 20.7 15.9 1.50 19.4 15.4 1.63

80/67 21.4 15.6 1.19 21.0 16.1 1.28 20.0 16.0 1.39 18.8 15.8 1.51 17.6 15.3 1.62

75/62* 19.5 15.8 1.20 19.0 16.1 1.29 18.1 16.1 1.40 17.1 15.8 1.50 16.1 15.3 1.61

70/57 17.6 15.7 1.21 17.3 16.0 1.30 16.6 15.8 1.39 15.7 15.0 1.50 14.8 14.2 1.60

850

85/72 23.9 16.7 1.16 23.3 17.2 1.26 22.2 17.2 1.38 20.9 17.1 1.50 19.5 16.6 1.63

80/67 21.9 16.7 1.18 21.3 17.1 1.28 20.2 17.1 1.39 19.0 17.0 1.51 17.9 16.5 1.63

75/62* 19.8 16.7 1.20 19.2 17.1 1.30 18.4 17.2 1.40 17.5 16.7 1.51 16.5 15.7 1.62

70/57 18.1 16.7 1.21 17.7 16.9 1.30 17.0 16.3 1.40 16.1 15.4 1.50 15.2 14.5 1.61

H4TS036 / G+FD048S21, 24

700

85/72 24.5 16.0 1.15 23.6 16.2 1.26 22.4 16.0 1.37 21.0 15.6 1.50 19.7 15.2 1.62

80/67 22.2 16.0 1.18 21.5 16.1 1.28 20.4 16.0 1.39 19.2 15.6 1.50 17.9 15.1 1.62

75/62* 20.2 16.1 1.19 19.5 16.3 1.29 18.5 16.0 1.39 17.3 15.7 1.50 16.2 15.2 1.61

70/57 18.3 16.1 1.20 17.6 16.1 1.29 16.8 16.0 1.39 15.9 15.3 1.49 15.0 14.4 1.59

750

85/72 24.7 16.5 1.15 23.8 16.8 1.25 22.6 16.7 1.37 21.2 16.3 1.50 19.8 15.9 1.62

80/67 22.4 16.5 1.18 21.7 16.8 1.28 20.6 16.6 1.39 19.3 16.2 1.50 18.1 15.8 1.62

75/62* 20.4 16.7 1.19 19.7 16.9 1.29 18.6 16.7 1.39 17.5 16.3 1.50 16.5 15.8 1.61

70/57 18.4 16.6 1.21 17.9 16.8 1.29 17.1 16.4 1.39 16.2 15.5 1.50 15.2 14.6 1.60

850

85/72 25.0 17.5 1.14 24.1 18.0 1.25 22.8 17.9 1.37 21.4 17.6 1.49 20.0 17.2 1.62

80/67 22.9 17.7 1.17 22.1 18.0 1.27 20.9 17.9 1.39 19.5 17.5 1.50 18.3 17.1 1.62

75/62* 20.7 17.7 1.19 20.0 18.1 1.29 19.0 17.9 1.40 17.9 17.2 1.51 16.9 16.2 1.62

70/57 18.9 17.7 1.20 18.4 17.7 1.29 17.6 16.9 1.40 16.6 15.9 1.50 15.6 15.0 1.61

Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder1 (Continued)

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

036-21023-002 Rev. A (5/00)

Unitary Products Group 9

H4TS048 / G+FD048S21, 24

900

85/72 30.2 20.0 1.39 28.6 19.5 1.55 27.0 18.9 1.70 25.3 18.3 1.84 23.7 17.8 1.97

80/67 27.6 20.0 1.38 26.1 19.4 1.54 24.7 18.9 1.68 23.2 18.3 1.81 21.6 17.7 1.93

75/62 25.1 20.2 1.37 23.8 19.6 1.52 22.4 19.1 1.66 21.0 18.4 1.78 19.5 17.7 1.89

70/57 22.6 20.1 1.36 21.5 19.7 1.51 20.3 19.0 1.63 19.2 18.2 1.75 18.0 17.1 1.86

1000

85/72 30.5 21.1 1.39 28.9 20.6 1.55 27.2 20.0 1.70 25.7 19.5 1.84 23.9 18.9 1.97

80/67 28.0 21.2 1.38 26.5 20.6 1.54 25.0 20.0 1.68 23.4 19.4 1.82 21.9 18.7 1.94

75/62 25.4 21.3 1.37 24.1 20.7 1.52 22.7 20.1 1.66 21.4 19.6 1.79 19.9 18.8 1.90

70/57 23.1 21.3 1.36 21.9 20.6 1.51 20.9 19.8 1.64 19.7 18.6 1.76 18.4 17.5 1.87

1100

85/72 30.7 22.2 1.39 29.3 21.8 1.56 27.6 21.2 1.71 25.9 20.5 1.85 24.1 19.9 1.98

80/67 28.3 22.3 1.38 26.8 21.7 1.54 25.2 21.0 1.69 23.6 20.4 1.82 22.0 19.7 1.94

75/62 25.7 22.4 1.37 24.3 21.7 1.53 23.0 21.2 1.67 21.7 20.6 1.79 20.4 19.3 1.91

70/57 23.6 22.4 1.37 22.5 21.3 1.51 21.3 20.2 1.65 20.0 19.0 1.77 18.7 17.8 1.88

H4TS048 / G+FD060S24

900

85/72 30.3 20.1 1.39 28.7 19.5 1.55 27.0 18.9 1.70 25.5 18.4 1.84 23.8 17.8 1.97

80/67 27.5 20.0 1.38 26.2 19.5 1.54 24.7 18.9 1.68 23.2 18.3 1.81 21.6 17.7 1.93

75/62 25.0 20.2 1.37 23.6 19.5 1.52 22.3 19.0 1.66 20.9 18.3 1.78 19.6 17.7 1.90

70/57 22.5 20.1 1.36 21.4 19.5 1.51 20.2 18.8 1.64 19.1 18.1 1.75 17.9 17.0 1.86

1000

85/72 30.6 21.2 1.39 29.0 20.6 1.55 27.5 20.1 1.71 25.7 19.5 1.84 24.0 18.9 1.97

80/67 28.0 21.2 1.38 26.5 20.6 1.54 25.0 20.0 1.68 23.4 19.4 1.82 21.8 18.7 1.94

75/62 25.3 21.3 1.37 24.0 20.7 1.52 22.6 20.0 1.66 21.3 19.4 1.79 19.8 18.6 1.90

70/57 23.0 21.2 1.36 21.8 20.5 1.51 20.8 19.7 1.64 19.6 18.5 1.76 18.3 17.3 1.87

1100

85/72 30.9 22.3 1.39 29.4 21.8 1.56 27.7 21.2 1.71 25.9 20.5 1.85 24.1 19.9 1.98

80/67 28.3 22.3 1.38 26.8 21.7 1.54 25.2 21.0 1.69 23.6 20.4 1.82 22.1 19.8 1.95

75/62 25.6 22.4 1.37 24.4 21.8 1.53 22.9 21.1 1.67 21.6 20.5 1.79 20.3 19.2 1.91

70/57 23.5 22.3 1.37 22.4 21.2 1.52 21.2 20.1 1.65 19.9 18.9 1.77 18.6 17.6 1.88

H4TS060 / G+FD060S24

1100

85/72 39.7 26.6 1.86 37.7 25.9 2.11 35.6 25.2 2.34 33.5 24.4 2.55 31.4 23.8 2.76

80/67 36.4 26.6 1.87 34.5 25.9 2.09 32.7 25.2 2.31 30.7 24.4 2.51 28.8 23.7 2.69

75/62 33.1 26.9 1.87 31.4 26.2 2.08 29.7 25.4 2.27 27.9 24.6 2.45 26.0 23.8 2.62

70/57 30.0 26.8 1.86 28.4 26.0 2.05 26.9 25.4 2.23 25.3 24.4 2.40 23.9 23.2 2.56

1200

85/72 40.1 27.8 1.86 38.0 27.1 2.11 35.9 26.4 2.34 33.9 25.7 2.56 31.7 24.9 2.77

80/67 36.7 27.8 1.87 34.9 27.2 2.10 33.0 26.4 2.31 31.0 25.6 2.51 29.0 24.8 2.70

75/62 33.5 28.1 1.87 31.8 27.4 2.08 30.0 26.6 2.28 28.1 25.7 2.46 26.4 25.0 2.64

70/57 30.3 28.0 1.86 28.9 27.3 2.06 27.4 26.6 2.24 25.9 25.1 2.41 24.4 23.6 2.58

1300

85/72 40.4 29.0 1.86 38.3 28.3 2.11 36.3 27.7 2.35 34.1 26.9 2.57 31.9 26.1 2.78

80/67 37.1 29.1 1.87 35.2 28.3 2.10 33.3 27.5 2.32 31.2 26.7 2.52 29.1 25.9 2.71

75/62 33.8 29.3 1.87 32.1 28.5 2.08 30.3 27.8 2.28 28.5 27.0 2.47 26.8 26.0 2.65

70/57 30.9 29.3 1.87 29.4 28.5 2.06 27.9 27.1 2.25 26.4 25.6 2.43 24.8 24.0 2.59

H4TS060 / G+FD061H24

1100

85/72 39.8 26.6 1.86 37.8 25.9 2.10 35.7 25.2 2.34 33.5 24.4 2.55 31.4 23.8 2.76

80/67 36.4 26.6 1.86 34.5 25.8 2.09 32.6 25.2 2.30 30.7 24.4 2.51 28.7 23.7 2.70

75/62 33.1 26.9 1.87 31.4 26.2 2.07 29.7 25.4 2.27 27.9 24.6 2.45 26.0 23.8 2.62

70/57 30.0 26.8 1.86 28.4 26.1 2.05 26.9 25.3 2.23 25.4 24.6 2.40 23.9 23.1 2.56

1200

85/72 40.1 27.8 1.86 38.1 27.1 2.11 35.9 26.4 2.34 33.9 25.7 2.56 31.7 25.0 2.77

80/67 36.8 27.9 1.86 34.9 27.2 2.10 33.0 26.4 2.31 31.0 25.6 2.51 28.9 24.8 2.71

75/62 33.5 28.1 1.87 31.8 27.4 2.08 30.0 26.6 2.28 28.1 25.8 2.46 26.4 25.0 2.64

70/57 30.4 28.1 1.86 28.9 27.3 2.06 27.5 26.6 2.24 25.9 25.1 2.41 24.4 23.6 2.58

Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder1 (Continued)

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

036-21023-002 Rev. A (5/00)

10 Unitary Products Group

1300

85/72 40.5 29.1 1.86 38.3 28.3 2.11 36.3 27.7 2.35 34.1 26.9 2.57 31.9 26.1 2.78

80/67 37.2 29.1 1.87 35.2 28.3 2.10 33.3 27.6 2.32 31.2 26.8 2.52 29.1 26.0 2.72

75/62 33.8 29.3 1.87 32.1 28.5 2.08 30.2 27.8 2.28 28.5 27.0 2.47 26.8 26.0 2.65

70/57 30.9 29.3 1.87 29.4 28.5 2.06 28.0 27.1 2.25 26.4 25.5 2.43 24.8 24.0 2.60

1. NOTES : All capacities are net indoor fan heat already deducted. KW rating is for outdoor unit only.*Indicates T.V.A. requirements at 75 DB/65 WB.

Table 4: SYSTEM COOLING CAPACITY - 1 Cylinder1 (Continued)

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder1

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

H4TS024 / G+FD024S14, 17

750

85/72 28.2 16.3 1.63 27.6 16.5 1.78 26.7 16.5 1.94 25.4 16.3 2.09 23.8 15.8 2.23

80/67 25.8 16.3 1.61 25.3 16.5 1.75 24.4 16.5 1.89 23.2 16.3 2.03 21.7 15.8 2.16

75/62* 23.4 16.3 1.58 22.9 16.6 1.71 22.1 16.6 1.84 21.0 16.5 1.97 19.7 16.0 2.09

70/57 21.1 16.3 1.56 20.7 16.6 1.68 20.1 16.7 1.80 19.1 16.4 1.92 17.9 15.8 2.03

800

85/72 28.5 16.7 1.64 27.9 16.9 1.79 26.9 17.1 1.94 25.5 16.9 2.10 23.9 16.4 2.24

80/67 26.0 16.7 1.61 25.5 17.0 1.75 24.6 17.0 1.90 23.3 16.9 2.04 21.8 16.4 2.17

75/62* 23.6 16.7 1.59 23.1 17.1 1.72 22.2 17.2 1.85 21.2 17.0 1.98 19.9 16.5 2.10

70/57 21.3 16.7 1.56 21.2 17.3 1.69 20.4 17.2 1.81 19.2 16.8 1.93 18.2 16.4 2.04

036-21023-002 Rev. A (5/00)

Unitary Products Group 11

850

85/72 28.6 17.1 1.64 28.0 17.4 1.79 27.0 17.5 1.95 25.6 17.4 2.10 23.9 16.9 2.25

80/67 26.2 17.0 1.62 25.7 17.4 1.76 24.7 17.5 1.90 23.4 17.4 2.04 22.0 17.0 2.17

75/62* 23.8 17.2 1.59 23.3 17.6 1.72 22.6 17.9 1.86 21.4 17.5 1.99 20.0 16.9 2.11

70/57 21.5 17.1 1.56 21.4 17.8 1.69 20.5 17.7 1.81 19.4 17.3 1.93 18.4 16.6 2.05

H4TS024 / G+FD030S17

750

85/72 29.0 16.6 1.62 28.4 16.8 1.76 27.3 16.8 1.92 25.9 16.6 2.07 24.2 16.0 2.21

80/67 26.5 16.6 1.59 26.0 16.9 1.73 24.9 16.8 1.87 23.7 16.6 2.01 22.1 16.0 2.14

75/62* 24.1 16.8 1.56 23.5 17.0 1.69 22.6 16.9 1.82 21.4 16.7 1.95 20.1 16.1 2.07

70/57 21.8 16.7 1.54 21.3 17.0 1.66 20.6 17.0 1.78 19.4 16.6 1.90 18.2 16.0 2.00

800

85/72 29.2 17.1 1.62 28.6 17.4 1.77 27.5 17.3 1.92 26.0 17.1 2.07 24.4 16.7 2.21

80/67 26.8 17.1 1.59 26.2 17.4 1.73 25.1 17.3 1.88 23.8 17.1 2.02 22.3 16.6 2.14

75/62* 24.3 17.2 1.57 23.7 17.5 1.70 22.8 17.5 1.83 21.6 17.3 1.96 20.3 16.7 2.08

70/57 22.0 17.2 1.54 21.7 17.7 1.66 20.8 17.6 1.79 19.6 17.1 1.90 18.6 16.7 2.02

850

85/72 29.4 17.5 1.62 28.8 17.8 1.77 27.6 17.9 1.93 26.2 17.7 2.08 24.4 17.2 2.22

80/67 27.0 17.5 1.60 26.4 17.9 1.74 25.3 17.9 1.88 23.9 17.7 2.02 22.4 17.2 2.15

75/62* 24.5 17.7 1.57 23.9 18.0 1.70 23.1 18.2 1.83 21.8 17.8 1.96 20.4 17.2 2.08

70/57 22.1 17.6 1.54 21.9 18.2 1.67 21.0 18.1 1.79 19.8 17.7 1.91 18.8 16.9 2.03

H4TS024 / G+FD036S17

750

85/72 29.8 17.1 1.61 29.0 17.3 1.76 27.8 17.1 1.91 26.2 16.7 2.07 24.5 16.2 2.21

80/67 27.2 17.1 1.59 26.5 17.3 1.73 25.4 17.1 1.87 23.9 16.7 2.01 22.4 16.2 2.13

75/62* 24.7 17.2 1.56 24.0 17.4 1.69 23.0 17.3 1.82 21.7 16.9 1.95 20.4 16.4 2.06

70/57 22.3 17.2 1.53 21.7 17.3 1.65 20.9 17.3 1.78 19.7 16.9 1.89 18.4 16.3 2.00

800

85/72 30.0 17.6 1.62 29.2 17.8 1.77 28.0 17.7 1.92 26.4 17.4 2.07 24.7 16.8 2.21

80/67 27.5 17.6 1.59 26.7 17.8 1.73 25.6 17.7 1.87 24.1 17.3 2.01 22.5 16.8 2.14

75/62* 24.9 17.7 1.56 24.2 17.9 1.70 23.2 17.8 1.82 21.9 17.6 1.95 20.5 17.0 2.07

70/57 22.5 17.7 1.54 22.1 18.1 1.66 21.1 17.8 1.78 19.9 17.5 1.90 18.8 16.9 2.01

850

85/72 30.2 18.0 1.62 29.4 18.3 1.77 28.1 18.2 1.92 26.5 17.9 2.08 24.8 17.4 2.22

80/67 27.7 18.1 1.59 26.9 18.3 1.74 25.7 18.2 1.88 24.3 18.0 2.02 22.8 17.5 2.15

75/62* 25.1 18.2 1.57 24.4 18.5 1.70 23.4 18.5 1.83 22.1 18.1 1.96 20.7 17.5 2.08

70/57 22.7 18.2 1.54 22.4 18.6 1.67 21.3 18.4 1.79 20.3 18.2 1.91 19.1 17.2 2.03

H4TS030 / G+FD030S17

950

85/72 33.8 20.6 1.96 33.4 21.0 2.20 32.4 21.0 2.47 31.0 20.7 2.79 29.5 20.1 3.16

80/67 31.1 20.8 1.92 30.7 21.1 2.15 29.8 21.1 2.41 28.5 20.7 2.72 27.0 20.2 2.08

75/62* 28.5 21.0 1.88 28.1 21.3 2.10 27.3 21.4 2.35 26.1 21.1 2.65 24.7 20.4 3.01

70/57 26.1 21.2 1.85 25.6 21.4 2.06 25.0 21.6 2.31 23.9 21.1 2.60 22.7 20.5 2.95

1000

85/72 34.0 21.1 1.96 33.6 21.4 2.21 32.6 21.5 2.48 31.1 21.1 2.80 29.6 20.7 3.17

80/67 31.3 21.2 1.92 30.9 21.5 2.15 30.0 21.6 2.41 28.6 21.2 2.72 27.2 20.7 3.09

75/62* 28.7 21.5 1.88 28.36 21.8 2.10 27.4 21.8 2.36 26.2 21.6 2.65 24.9 21.1 3.01

70/57 26.2 21.6 1.85 25.8 21.9 2.06 25.2 22.1 2.31 24.1 21.7 2.60 22.9 21.1 2.96

1100

85/72 34.4 21.8 1.97 33.9 22.3 2.21 32.8 22.4 2.48 31.5 22.3 2.80 29.8 21.7 3.18

80/67 31.7 22.0 1.92 31.2 22.4 2.15 30.3 22.6 2.42 28.8 22.2 2.73 27.4 21.8 3.09

75/62* 29.0 22.3 1.88 28.6 22.7 2.10 27.7 22.9 2.36 26.5 22.6 2.66 25.1 22.0 3.02

70/57 26.5 22.4 1.85 26.4 23.2 2.07 25.5 23.0 2.31 24.4 22.6 2.61 23.1 21.9 2.96

H4TS030 / G+FD036S21

950

85/72 35.0 21.0 2.00 34.6 21.4 2.24 33.4 21.3 2.52 32.0 21.0 2.84 30.4 20.4 3.22

80/67 32.2 21.1 1.95 31.8 21.5 2.18 30.8 21.5 2.45 29.5 21.1 2.76 27.9 20.5 3.13

75/62* 29.5 21.4 1.91 29.1 21.8 2.13 28.2 21.7 2.39 26.9 21.3 2.69 25.6 20.7 3.06

70/57 27.0 21.5 1.87 26.7 22.0 2.09 25.8 21.8 2.34 24.6 21.4 2.64 23.4 20.8 2.99

Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder1 (Continued)

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

036-21023-002 Rev. A (5/00)

12 Unitary Products Group

1000

85/72 35.2 21.4 2.00 34.7 21.9 2.25 33.5 21.7 2.52 32.2 21.6 2.85 30.5 21.0 3.22

80/67 32.4 21.5 1.95 32.0 22.0 2.19 31.0 22.0 2.45 29.6 21.7 2.76 28.1 21.1 3.14

75/62* 29.7 21.8 1.91 29.3 22.3 2.13 28.4 22.3 2.39 27.1 21.9 2.70 25.8 21.4 3.06

70/57 27.1 21.9 1.87 26.9 22.5 2.09 26.0 22.4 2.34 24.8 21.9 2.64 23.6 21.4 2.99

1100

85/72 35.5 22.2 2.01 35.1 22.8 2.25 33.9 22.9 2.53 32.5 22.7 2.85 30.8 22.2 3.32

80/67 32.8 22.4 1.96 32.3 22.9 2.19 31.2 22.9 2.46 29.8 22.7 2.77 28.4 22.2 3.14

75/62* 30.0 22.7 1.91 29.7 23.3 2.14 28.8 23.4 2.40 27.4 23.0 2.70 26.0 22.5 3.06

70/57 27.7 23.0 1.88 27.3 23.4 2.10 26.3 23.4 2.35 25.2 23.1 2.64 23.9 22.4 3.00

H4TS030 / G+FD042S21

950

85/72 35.9 22.6 2.00 35.4 22.9 2.25 34.1 22.6 2.52 32.7 22.5 2.84 31.1 21.9 3.22

80/67 33.1 22.7 1.95 32.6 23.0 2.19 31.4 22.8 2.45 30.0 22.5 2.76 28.4 21.8 3.13

75/62* 30.3 23.0 1.91 29.8 23.3 2.13 28.7 23.1 2.39 27.4 22.7 2.69 26.1 22.2 2.99

70/57 27.6 23.1 1.87 27.3 23.5 2.09 26.4 23.3 2.34 25.1 22.9 2.63 23.8 22.3 2.99

1000

85/72 36.1 23.0 2.01 35.6 23.4 2.25 34.3 23.2 2.53 32.9 23.1 2.85 31.1 22.4 3.22

80/67 33.3 23.2 1.96 32.8 23.5 2.19 31.6 23.4 2.46 30.2 23.1 2.76 28.7 22.5 3.13

75/62* 30.5 23.5 1.91 30.0 23.8 2.14 28.9 23.8 2.39 27.6 23.4 2.69 26.2 22.7 3.06

70/57 27.8 23.6 1.87 27.5 24.1 2.09 26.5 23.9 2.34 25.3 23.5 2.64 23.9 22.8 2.99

1100

85/72 36.5 23.9 2.01 35.9 23.4 2.26 34.7 23.2 2.53 33.1 24.2 2.85 31.4 23.6 3.23

80/67 33.6 24.0 1.96 33.1 24.5 2.19 31.9 24.6 2.46 30.4 24.3 2.77 29.0 23.7 3.14

75/62* 30.8 24.4 1.91 30.3 24.9 2.14 29.3 25.0 2.40 27.9 24.5 2.70 26.5 23.9 3.06

70/57 28.3 24.6 1.88 27.9 25.1 2.10 26.9 25.0 2.34 25.6 24.6 2.64 24.3 23.9 3.00

H4TS036 / G+FD036S21

1100

85/72 40.3 24.7 2.31 39.4 24.9 2.52 37.9 24.9 2.73 35.9 24.4 2.95 33.8 23.8 3.16

80/67 36.9 24.6 2.28 36.1 25.0 2.48 34.7 24.9 2.68 32.8 24.4 2.89 30.8 23.7 3.08

75/62* 33.7 24.9 2.25 32.9 25.2 2.43 31.6 25.2 2.62 29.9 24.6 2.82 28.0 23.8 3.00

70/57 30.6 24.9 2.21 30.1 25.3 2.39 28.8 25.2 2.57 27.1 24.6 2.75 25.5 23.8 2.91

1200

85/72 40.7 25.6 2.31 39.7 25.9 2.52 38.2 26.0 2.74 36.2 25.6 2.96 34.0 24.9 3.17

80/67 37.3 25.5 2.28 36.5 25.9 2.48 35.0 26.0 2.69 33.1 25.6 2.89 31.1 24.8 3.09

75/62* 34.0 25.8 2.25 33.4 26.4 2.44 32.0 26.3 2.63 30.2 25.7 2.83 28.3 24.9 3.01

70/57 31.3 26.1 2.22 30.4 26.3 2.40 29.1 26.2 2.58 27.5 25.7 2.76 26.0 24.8 2.94

1300

85/72 40.9 26.3 2.31 40.0 26.8 2.53 38.5 27.0 2.74 36.4 26.7 2.97 34.2 25.9 3.18

80/67 37.6 26.3 2.29 36.7 26.9 2.49 35.4 27.1 2.70 33.4 26.7 290 31.3 25.8 3.10

75/62* 34.3 26.6 2.26 33.7 27.3 2.45 32.3 27.3 2.64 30.4 26.8 2.84 28.6 26.1 3.02

70/57 31.6 26.9 2.23 30.8 27.3 2.40 29.5 27.3 2.59 28.0 26.8 2.78 26.4 25.2 2.96

H4TS036 / G+FD042S21

1100

85/72 40.5 24.8 2.31 39.5 25.1 2.51 38.0 25.0 2.73 35.9 24.5 2.95 33.8 23.8 3.15

80/67 37.1 24.9 2.28 36.2 25.1 2.48 34.7 24.9 2.68 32.8 24.5 2.88 30.8 23.7 3.08

75/62* 33.9 25.1 2.25 33.0 25.4 2.43 31.6 25.3 2.62 29.8 24.6 2.81 27.9 23.8 2.99

70/57 30.8 25.2 2.21 30.1 25.5 2.39 28.8 25.3 2.56 27.0 24.6 2.74 25.4 23.8 2.91

1200

85/72 40.9 25.7 2.31 39.9 26.1 2.52 38.2 26.0 2.74 36.2 25.7 2.95 33.9 24.8 3.17

80/67 37.5 25.8 2.28 36.6 26.1 2.48 35.0 26.0 2.69 33.1 25.6 2.89 31.1 24.8 3.09

75/62* 34.2 26.0 2.25 33.3 26.4 2.44 32.0 26.4 2.63 30.1 25.7 2.82 28.2 24.9 3.01

70/57 31.4 26.4 2.22 30.5 26.5 2.39 29.1 26.3 2.57 27.5 25.7 2.75 25.9 24.9 2.93

1300

85/72 41.2 26.5 2.31 40.2 27.0 2.52 38.5 27.0 2.74 36.3 26.6 2.96 34.2 26.0 3.17

80/67 37.8 26.6 2.29 36.9 27.1 2.49 35.2 27.0 2.69 33.3 26.6 2.90 31.3 25.8 3.10

75/62* 34.5 26.9 2.26 33.8 27.5 2.45 32.3 27.4 2.64 30.4 26.8 2.83 28.5 26.1 3.02

70/57 31.7 27.2 2.22 30.8 27.5 2.40 29.5 27.4 2.59 28.0 26.9 2.77 26.4 25.3 2.95

H4TS036 / G+FD048S21, 24

Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder1 (Continued)

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

036-21023-002 Rev. A (5/00)

Unitary Products Group 13

1100

85/72 42.2 25.8 2.33 40.9 25.9 2.54 39.0 25.5 2.76 36.8 24.9 2.98 34.5 24.1 3.19

80/67 38.7 25.9 2.30 37.5 25.9 2.51 35.7 25.5 2.71 33.6 24.9 2.91 31.5 24.1 3.12

75/62* 35.2 26.1 2.27 34.1 26.1 2.46 32.4 25.7 2.66 30.5 25.1 2.84 28.6 24.2 3.03

70/57 32.0 26.1 2.24 31.1 26.3 2.41 29.4 25.7 2.60 27.7 25.1 2.77 25.9 24.2 2.94

1200

85/72 42.6 26.8 2.33 41.3 26.9 2.55 39.3 26.6 2.77 37.0 26.0 2.99 34.7 25.3 3.20

80/67 39.1 26.9 2.31 37.9 27.0 2.51 36.0 26.6 2.72 33.9 26.0 2.93 31.9 25.4 3.13

75/62* 35.7 27.1 2.28 34.6 27.4 2.47 32.8 26.9 2.67 30.8 26.2 2.86 28.9 25.5 3.04

70/57 32.6 27.4 2.25 31.5 27.3 2.43 29.8 26.8 2.61 28.1 26.2 2.79 26.6 25.4 2.97

1300

85/72 43.0 27.7 2.34 41.7 28.0 2.55 39.7 27.9 2.77 37.3 27.2 3.00 35.1 26.6 3.21

80/67 39.5 27.8 2.31 38.2 28.0 2.52 36.4 27.9 2.73 34.2 27.2 2.94 32.0 26.4 3.14

75/62* 36.0 28.1 2.28 35.0 28.4 2.48 33.2 28.1 2.67 31.2 27.5 2.87 29.2 26.6 3.06

70/57 33.0 28.3 2.25 31.9 28.4 2.43 30.3 28.1 2.62 28.8 27.4 2.81 27.1 25.8 2.99

H4TS048 / G+FD048S21, 24

1450

85/72 58.3 36.5 3.76 55.7 35.5 4.03 53.0 34.5 4.33 50.1 33.4 4.62 47.2 32.3 4.92

80/67 53.5 36.6 3.67 51.0 35.6 3.09 48.5 34.5 4.19 45.8 33.4 4.47 43.1 32.2 4.73

75/62* 48.6 36.9 3.57 46.4 35.9 3.80 44.0 34.8 4.05 41.5 33.6 4.50 39.2 32.8 4.55

70/57 44.2 37.0 3.47 42.3 36.2 3.69 40.1 35.0 3.92 37.8 33.7 4.15 35.5 32.5 4.37

1600

85/72 59.0 38.0 3.78 56.3 37.0 4.06 53.5 36.0 4.35 50.6 34.9 4.65 47.6 33.8 4.95

80/67 54.1 38.1 3.69 51.6 37.1 3.95 49.0 36.0 4.22 46.3 34.9 4.50 43.5 33.7 4.76

75/62* 49.3 38.5 3.60 46.9 37.4 3.83 44.5 36.3 4.08 42.3 35.5 4.34 39.7 34.2 4.59

70/57 45.1 38.9 3.50 42.9 37.7 3.72 40.7 36.5 3.95 38.4 35.2 4.18 36.2 34.4 4.42

1750

85/72 59.6 39.5 3.80 56.8 38.5 4.08 54.0 37.4 4.37 51.0 36.3 4.68 48.0 35.2 4.97

80/67 54.7 39.6 3.71 52.1 38.5 3.97 49.4 37.4 4.24 46.6 36.3 4.52 43.8 35.1 4.79

75/62* 49.8 40.0 3.61 47.4 38.9 3.85 45.3 38.1 4.11 42.7 36.9 4.37 40.1 35.6 4.62

70/57 45.7 40.3 3.52 43.5 39.1 3.74 41.2 37.9 3.98 39.1 37.1 4.22 36.7 35.5 4.45

Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder1 (Continued)

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

036-21023-002 Rev. A (5/00)

14 Unitary Products Group

H4TS048 / G+FD060S24

1450

85/72 59.6 38.1 3.72 56.8 37.0 3.99 54.0 35.9 4.28 51.0 34.7 4.58 48.0 33.5 4.87

80/67 54.7 38.2 3.63 52.1 37.1 3.88 49.4 35.9 4.15 46.7 34.7 4.43 43.8 33.4 4.69

75/62* 49.8 38.6 3.54 47.4 37.4 3.77 44.9 36.2 4.01 42.3 34.9 4.26 39.9 33.9 4.52

70/57 45.2 38.6 3.44 43.3 37.7 3.66 41.0 36.4 3.88 38.6 35.1 4.12 36.1 33.7 4.33

1600

85/72 60.3 39.7 3.74 57.5 38.6 4.01 54.6 37.5 4.31 51.5 36.3 4.61 48.5 35.1 4.90

80/67 55.4 39.9 3.65 52.7 38.7 3.91 50.0 37.5 4.18 47.2 36.3 4.46 44.3 35.0 4.72

75/62* 50.5 40.3 3.56 48.0 39.1 3.79 45.4 37.8 4.04 43.1 36.9 4.30 40.5 35.5 4.55

70/57 46.2 40.6 3.47 44.0 39.3 3.66 41.6 38.0 3.91 39.1 36.6 4.15 36.6 35.2 4.37

1750

85/72 60.9 41.3 3.75 58.0 40.2 4.03 55.0 39.0 4.33 52.0 37.8 4.63 48.8 36.6 4.93

80/67 56.0 41.4 3.67 53.3 40.3 3.92 50.5 39.0 4.20 47.6 37.8 4.48 44.9 36.8 4.76

75/62* 51.0 41.9 3.57 48.5 40.7 3.81 46.3 39.7 4.07 43.6 38.3 4.33 40.9 36.9 4.58

70/57 46.8 41.9 3.49 44.5 40.6 3.70 42.1 39.3 3.94 39.6 37.9 4.17 37.4 36.6 4.42

H4TS060 / G+FD060S24

1700

85/72 69.9 42.9 4.54 66.8 41.8 4.91 63.5 40.7 5.29 60.2 39.5 5.67 56.7 38.3 6.03

80/67 64.2 43.1 4.37 61.3 41.9 4.71 58.3 40.7 5.05 55.1 39.5 5.40 51.8 38.2 5.73

75/62* 58.5 43.5 4.20 55.8 42.3 4.51 53.0 41.1 4.82 51.3 40.1 5.15 47.3 38.7 5.45

70/57 53.5 43.9 4.05 51.0 42.6 4.33 48.4 41.3 4.62 45.7 39.9 4.91 42.9 38.5 5.19

1900

85/72 70.8 45.1 4.58 67.7 44.1 4.95 64.3 42.9 5.33 60.9 41.8 5.70 57.3 40.6 6.07

80/67 65.1 45.4 4.40 62.1 44.2 4.74 59.0 43.0 5.09 55.8 41.8 5.44 52.6 40.7 5.80

75/62* 59.4 45.9 4.23 56.6 44.6 4.54 53.9 43.5 4.88 51.0 42.2 5.20 47.9 40.8 5.51

70/57 54.4 46.1 4.08 51.8 44.8 4.37 49.1 43.4 4.67 46.4 42.1 4.96 43.9 40.9 5.25

2000

85/72 71.2 46.2 4.59 68.0 45.1 4.97 64.6 44.0 5.35 61.1 42.8 5.72 57.5 41.6 6.09

80/67 65.5 46.4 4.41 62.4 45.3 4.76 59.3 44.1 5.11 56.2 43.0 5.49 52.9 41.7 5.82

75/62* 59.8 47.0 4.24 57.1 45.9 4.57 54.3 44.6 4.90 51.3 43.2 5.22 48.2 41.8 5.54

70/57 54.8 47.1 4.10 52.2 45.8 4.39 49.5 44.4 4.69 47.0 43.5 4.99 44.8 42.5 5.33

H4TS060 / G+FD061H24

1700

85/72 70.7 44.1 4.57 67.5 43.0 4.95 64.3 41.8 5.33 60.9 40.6 5.70 57.2 39.3 6.08

80/67 64.9 44.3 4.40 62.0 43.1 4.74 58.9 41.9 5.09 55.7 40.7 5.43 52.3 39.2 5.78

75/62* 59.1 44.8 4.22 56.4 43.5 4.53 53.5 42.3 4.85 50.7 41.0 5.19 47.6 39.6 5.50

70/57 53.9 44.9 4.07 51.4 43.6 4.36 48.8 42.3 4.66 46.0 40.9 4.95 43.2 39.5 5.23

1900

85/72 71.5 46.3 4.62 68.3 45.1 5.00 64.9 43.9 5.38 61.4 42.7 5.76 57.9 41.7 6.12

80/67 65.7 46.4 4.44 62.7 45.2 4.78 59.5 44.0 5.14 56.2 42.7 5.49 53.1 41.9 5.84

75/62* 59.9 46.9 4.26 57.1 45.7 4.58 54.5 44.8 4.91 51.5 43.4 5.23 48.4 42.0 5.54

70/57 54.9 47.3 4.11 52.3 46.0 4.40 49.6 44.7 4.70 47.0 43.5 5.02 44.2 41.9 5.30

2000

85/72 71.9 47.4 4.63 68.6 46.2 5.02 65.2 45.0 5.40 61.8 44.0 5.78 58.0 42.6 6.16

80/67 66.1 47.5 4.45 63.0 46.3 4.80 59.8 45.1 5.16 56.7 44.1 5.53 53.4 42.9 5.86

75/62* 60.3 48.1 4.28 57.7 47.2 4.60 54.8 45.9 4.93 51.8 44.5 5.26 48.6 43.1 5.57

70/57 55.3 48.5 4.12 52.7 47.1 4.42 49.9 45.8 4.72 47.4 44.5 5.03 45.2 43.6 5.38

1. NOTES : All capacities are net indoor fan heat already deducted. KW rating is for outdoor unit only.*Indicates T.V.A. requirements at 75 DB/65 WB.

Table 5: SYSTEM COOLING CAPACITY - 2 Cylinder1 (Continued)

INDOORAIR

CONDENSER ENTERING AIR TEMPERATURE

75 °F 85 °F 95 °F 105 °F 115 °FTotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

TotalCap.MBH

SensibleCap.MBH

PowerInputKW

CFM DB/WD

036-21023-002 Rev. A (5/00)

Unitary Products Group 15

ACCESSORIES (Refer to Price Manual for specific model numbers.)

Dehumidification Control - Model 2HU06700124 available for usein areas where a higher level of humidity control is required.

Room Thermostat - Matching 2-Stage cooling thermostats are avail-able to provide features required for any installation. See list below:

2ET03700024 2ET03700124 2ET03700224 2ET03700324

TXV Kit - Factory specified and required for proper unit performance.H4TS024 = 1TV0701H4TS030 = 1TV0701H4TS036 = 1TV0702

H4TS048 = 1TV0704 (w/ 4 ton evap coils) 1TV0703 (w/ 5 ton evap coils)

H4TS060 = 1TV0703

Table 6: PHYSICAL AND ELECTRICAL DATAMODEL H4TS024 H4TS030 H4TS036 H4TS048 H4TS060

UNIT SUPPLY VOLTAGE 208/230-1-60

NORMAL VOLTAGE RANGE 1 187 to 252

MIN. CIRCUIT AMPACITY 13.4 15.3 18.6 32.8 35.3

MAX. OVERCURRENT DEVICE AMPS 2 20 25 30 50 60

COMPRESSOR TYPE BRISTOL TS

COMPRESSOR AMPSRATED LOAD 10.3 11.7 13.5 25.7 27.0

LOCKED ROTOR 64 65 84 135 147

CRANKCASE HEATER YES YES YES YES YES

FAN MOTOR AMPS RATED LOAD .5 .5 .7 .7 1.5

FAN DIAMETER INCHES 18 18 24 24 24

FAN MOTOR

RATED HP 1/12 1/12 1/10 1/10 1/4

NOMINAL RPM 1100 1100 825 825 850

NOMINAL CFM 1850 1850 2800 2800 3200

COIL

FACE AREA SQ. FT 14.2 14.2 20.0 24.0 24.0

COIL ROWS DEEP 1 1 1 1 1

FIN / INCH 20 20 20 20 20

LIQUID LINE OD 3/8 3/8 3/8 3/8 3/8

VAPOR LINE OD 3/4 3/4 7/8 7/8 7/8

UNIT CHARGE, (LBS - OZ)3 5 - 9 6 - 9 7 - 0 9 - 12 9 - 2

CHARGE PER FOOT, OZ .68 .68 .70 .7 .7

OPERATING WEIGHT LBS. 145 145 200 250 2521 Rated in accordance with ARI Standard 110. utilization range “A”.2 Dual element fuses or HACR circuit breaker.3 The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other

than 15 feet, add or subtract the amount of refrigerant calculated, using the difference in length multiplied by the per foot value.

UNITMODEL

HTS

DIMENSIONS

REFRIGERANTCONNECTION

LINE SIZE

A B C LIQUID VAPOR

024 30-1/8 24 24

3/8

3/4030 30-1/8 24 24

036 31-7/8 35 35

7/8048 37-7/8 35 35

060 37-7/8 35 35

48" OVERHEAD

CLEARANCE

C

B

A

5-1/2

2-3/8

3-1/8

VAPOR

CONNECTION

LIQUID CONNECTION

AIR IN

4 SIDES

��������������� ���� ����

Unitary Products Group5005 York Drive, Norman, Oklahoma 73069Subject to change without notice. Printed in U.S.A. 036-21023-003 Rev. A (0500)Copyright © by Unitary Products Group 2000. All rights reserved. Supersedes: 550.37-TG4Y (0200) & 036-21023-002A (0200)

MATCHING INDOOR COMPONENTSAdd-On Coils - For Furnace Application Air Handlers - For Non-Furnace Application

G-UA COIL

G-HD COIL

G+FD COIL

N-AHBLOWER/

G+FD COIL

F2RC / F2FC OR F2RP / F2FP

FAN COIL UNITS

UPFLOW DOWNFLOW

HORIZONTAL

UPFLOWHORIZONTAL