DECIMAL EQUIVALENTS - McMillan Rod & Custom 2020.pdf · McMillan Rod & Custom M243 Highway T • Marshfield, WI 54449 Phone: 715-387-6847 • Cell: 715-305-1069 Email: [email protected]

Jim & Carol StaunerMcMillan Rod & Custom

M243 Highway T • Marshfield, WI 54449Phone: 715-387-6847 • Cell: 715-305-1069

Email: [email protected]

www.mcmi l l anrodandcus tom.com

Fabricators of polished stainless steelcomponents for Hotrods and Customs.

CATALOG

DECIMAL EQUIVALENTS

COURTESY OF MCMILLAN ROD & CUSTOM

TO ORDER CALL: 715-387-6847

www.mcmillanrodandcustom.comLIKE US ON FACEBOOK TO WATCH FOR SPECIALS!

TABLE OF CONTENTS

MOLDINGS ..............................................3 RUNNING BOARD STRIP KITS ..........5

NERF BARS..............................................................................6

CHIN BARS AND BUMPERS ..........................................................................................10

HOOD SIDE VENTS..............................14AIR CLEANERS .....................................13

MCMILLAN ROD & CUSTOM PAGE 3


HALF ROUND SOLIDSTAINLESS STEEL MOLDINGS

Moldings are available in 1/4”, 3/8”, 1/2”, 5/8” and 3/4” wide. These moldings have a multitude of possibilities for your vehicle’s interior and/or exterior. Moldings are half round solid stainless steel and sold by the linear foot. The moldings are machined from solid, type 304 stainless steel and polished to a mirror finish.

Call for quote 715-387-6847 or lay out your pattern full size, mark where you want the studs, include shape of ends, roll it up, insert into a shipping tube and mail it to us.

Below are options for end configurations. Diagonal is also available.

TO ORDER CALL: 715-387-6847 MCMILLAN ROD & CUSTOM

www.mcmi l l anrodandcus tom.comLIKE US ON FACEBOOK TO WATCH FOR SPECIALS!


PAGE 14 PAGE 3

MOTORCYCLE ACCENTS

HOOD SIDE VENTS

We offer a line of saddlebag trim products all from polished stainless steel. The trim is built from our 1/2” solid stainless steel molding stock, polished to a mirror finish, complete with studs installed. The set comes with (2) 16” and (4) 12” strips.

Precision cut from 16 gauge stainless steel, these are fully functional vents and are designed to bolt on. Sold in pairs and available in single, double, or triple designs. These also work well for interior accents and saddle bag trim.

HALF ROUND SOLID STAINLESS STEEL MOLDINGS




The studs are either 6-32 (used on the 1/4” molding) or 8-32 (used on 3/8” and up). The 8-32 stud is shown below on ½” molding. Studs are 3/4” long

in stainless steel and installed with a stud welding process. Mounting studs are recommended for door panels and applications outside of your ride.

Bullet (pointed) Rolled Round StraightBullet (Pointed) Rolled Round Straight


in stainless steel and installed with a stud welding process. Mounting studs are recommended for door panels and applications outside of your ride and are $5 each.




PAGE 14 PAGE 3

MOTORCYCLE ACCENTS

HOOD SIDE VENTS









Bullet (pointed) Rolled Round Straight



MOLDINGS3/4” half round ..............................................................................................$25/foot5/8” half round ..............................................................................................$23/foot1/2” half round ................................................................$18-$21/foot (See below) Up to 3 feet is $21/foot 3-10’ is $20/foot 10-20’ is $19/foot Over 20’ is $18/foot3/8” half round ..............................................................................................$24/foot1/4” half round ..............................................................................................$23/foot

LOW PROFILE MOLDINGS

McMillan Rod and Custom low profile moldings offer a lower height profile than there standard half round moldings.

The low profile moldings are solid, type 304 stainless steel and polished to a mirror finish.

Options for end configurations include bullet (pointed), rolled, round, diagonal and straight. Mounting studs are recommended for exterior applications. Recommended studs are an 8-32 x ¾” and are $5 each.

The cost is by the linear foot: 1/2” (5/32” thick) = $20/foot3/4” (3/16” thick) = $25/foot 1” (1/4” thick) = $30/foot 1 1/4” (1/4” thick) = $35/foot



RUNNING BOARD STRIP KITS“Standard Universal Kit” is made from type 304 stainless steel half round strips and polished to a mirror finish. Comes in 1/2” ($435) or 5/8” ($495) wide and includes (2) 42” and (4) 36”. Three studs are installed on each strip with your choice of bullet (pointed) or rounded ends.




PAGE 4 PAGE 13

CUSTOM BUMPER BRACKETSWe offer to take your ugly and pitted bumper brackets and reproduce them in polished stainless steel. We can also shorten them to bring the bumper in closer to the body.

NOTES

RUNNING BOARD STRIP KITS“Standard Universal Kit” is made from type 304 stainless steel half round strips and polished to a mirror finish. Comes in 1/2” or 5/8” wide and includes (2) 42” and (4) 36”. Three studs are installed on each strip with your choice of bullet (pointed) or rounded ends.

“Short Running Board Kit” comes in 1/2” or 5/8” wide and includes (2) 36” and (4) 32” with 3 studs installed on each strip. (These fit shorter running boards including a ‘32 Ford.)

*Other lengths and widths are available. Call for pricing. 715-387-6847




PAGE 4 PAGE 13


NOTES







PAGE 4 PAGE 13


NOTES




“Short Running Board Kit” comes in 1/2” ($395) or 5/8” ($435) wide and includes (2) 36” and (4) 32” with 3 studs installed on each strip. (These fit shorter running boards including a ‘32 Ford.)




NERF BARSAll of our nerf bars are made from 3/4” solid stainless. The mounting bracket is 2”x10”x 3/16” stainless. The entire piece is ground and polished to a mirror finish and sold as a set of two.

8” DOUBLE BEND NERF BARS $150

These are our best sellers. The vertical bar is 8” tall.




PAGE 7PAGE 10

1932 Ford Double Chin Bar with or without V8Built from solid 3/4” diameter, type 304 stainless steel and polished to a mirror like finish. This chin bar offers a new look, and an alternative to the traditional straight or V shaped spreader bar while maintaining the traditional look of a ‘32. Also available for model A’s and pinched frames by special order.

1933/1934 Ford Single Chin BarBuilt specifically for a 1933/34 Ford, it utilizes our 10” nerf bars with 20 degree brackets and joined by a horizontal stainless bar following the contour of the body. TIG welded, ground, and polished to a mirror finish.

1933/1934 Ford Rear BumperBuilt from high quality, solid type 304 stainless steel and polished to a mirror like finish. The horizontal bar is built from 3/4” solid round. Brackets are our popular sleeve style that allows 2 way adjustments for a better fit.

CHIN BARS AND BUMPERS NERF BARS

8” Double bend nerf barsThese are our best sellers. The vertical bar is 8” tall.

All of our nerf bars are made from 3/4” solid stainless. The mounting bracket is 2”x10”x 3/16” stainless. The entire piece is ground and polished to a mirror finish and sold as a set of two.

10” Double bend nerf barsSame as the above only the vertical bar is 10” tall.

10” DOUBLE BEND NERF BARS $160

Same as the above only the vertical bar is 10” tall.




PAGE 7PAGE 10










8” OR 10” DOUBLE BEND NERF BARS WITH 20 DEGREE BRACKETS $165/$175

While built specifically for Ford Model A’s, 32’s, and 33/34 Fords, these nerfs can be used on the front of many streetrods having frame horns that curve down. The mounting brackets have a 20 degree bend in them to keep the vertical bar square to the ground.

V-NERF BARS $145

Vertical bar is 8” tall and bent to a V shape.




PAGE 8 PAGE 9

1933/1934 ford FLAT and drilled nerf barsBuilt from 3/8” thick type 304 stainless steel, these nerf bars are contoured to fit the downward arc of the front frame horns. Each nerf bar is precision cut with a water jet and then polished by hand to a mirror finish. Nerfs come without the mounting holes drilled but if you would like, we can drill them at no extra charge. Comes as a set of two.

BUMPERETTESBumperettes are 12” wide and made from our ¾” moldings and are available in straight or 20 degree brackets.

Gullwing nerfs10” tall vertical bar.

V-nerfsVertical bar is 8” tall and bent to a V shape.

8” or 10” Double bend nerf bars with 20 degree bracketsWhile built specifically for Ford Model A’s, 32’s, and 33/34 Fords, these nerfs can be used on the front of many streetrods having frame horns that curve down. The mounting brackets have a 20 degree bend in them to

keep the vertical bar square to the ground.



GULLWING NERF BARS $175

Vertical bar is 10” tall.




PAGE 8 PAGE 9







BUMPERETTES $225/$240Bumperettes are 12” wide and made from our ¾” moldings and are available in straight or 20 degree brackets.




PAGE 8 PAGE 9







SIDE NERF BARS STARTING AT $350

These are “sprint car style” side nerf bars, built from solid 3/4” type 304 stainless steel to your specifications and polished to a mirror finish.



1933/1934 FORD FLAT AND DRILLED NERF BARS $225

Built from 3/8” thick type 304 stainless steel, these nerf bars are contoured to fit the downward arc of the front frame horns. Each nerf bar is precision cut with a water jet and then polished by hand to a mirror finish. Nerfs come without the mounting holes drilled but if you would like, we can drill them at no extra charge. Comes as a set of two.




PAGE 8 PAGE 9







8” OR 10” CHEVROLET NERF BARS $185/$195

These are built specifically for early Chevrolets. They are available in 8” or 10” double bend versions with 9/16” threads, allowing them to be threaded into the frame rails. Built from solid type 304 stainless steel and polished to a mirror finish. They come as a set of two complete with jam nuts. While originally designed for early Chevy’s they also work well in other applications like the 36 Ford pictured below.



CHIN BARS AND BUMPERS1932 FORD DOUBLE CHIN BAR WITH OR WITHOUT V8

$330/$310Built from solid 3/4” diameter, type 304 stainless steel and polished to a mirror like finish. This chin bar offers a new look, and an alternative to the traditional straight or shaped spreader bar while maintaining the traditional look of a ‘32. Also available for model A’s and pinched frames by special order.




PAGE 7PAGE 10











PAGE 7PAGE 10











PAGE 7PAGE 10








1933/1934 FORD SINGLE CHIN BAR $305Built specifically for a 1933/34 Ford, it utilizes our 10” nerf bars with 20 degree brackets and joined by a horizontal stainless bar following the contour of the body. TIG welded, ground, and polished to a mirror finish.

1933/1934 FORD REAR BUMPER $425Built from high quality, solid type 304 stainless steel and polished to a mirror like finish. The horizontal bar is built from 3/4” solid round. Brackets are our popular sleeve style that allows 2 way adjustments for a better fit.



‘35 - ‘40 FORD SINGLE CHIN BAR $290Built from high quality, solid type 304 stainless steel and polished to a mirror like finish. We use our 10” double bend nerf bars with a horizontal bar built from 3/4” solid round.

’35 – ’40 FORD DOUBLE CHIN BAR $385The two horizontal bars are made from 3/4” solid round with our V nerf bars. This may fit other makes of cars.

‘36-‘40 FORD SINGLE CHIN BAR WITHOUT NERF BARS $325

This bar is made from 3/4” solid round stainless steel and designed to fit cars with filled bumper bracket holes. Our sleeve type brackets allow for maximum adjustability.




PAGE 6 PAGE 11

‘35 - ‘40 Ford Single Chin BarBuilt from high quality, solid type 304 stainless steel and polished to a mirror like finish. We use our 10” double bend nerf bars with a horizontal bar built from 3/4” solid round.

’35 – ’40 Ford Double Chin BarThe two horizontal bars are made from 3/4” solid round with our V nerf bars. This may fit other makes of cars.

‘36-‘40 Ford Single Chin Bar WITHOUT Nerf BarsThis bar is made from 3/4” solid round stainless steel and designed to fit cars with filled bumper bracket holes. Our sleeve type brackets allow for maximum adjustability.

8 STACK INJECTION STYLEThis is a multi-stack injection looking air cleaner complete with filter element, mounting screw and base. Stacks are available in 6” or 8” tall or custom lengths.

8 STACK INJECTION STYLE STAGGEREDThe 8-stack injection air cleaner is available with 8” tall staggered stacks also. If you want something different, this one is for you.




PAGE 6 PAGE 11

‘35 - ‘40 Ford Single Chin BarBuilt from high quality, solid type 304 stainless steel and polished to a mirror like finish. We use our 10” double bend nerf bars with a horizontal bar built from 3/4” solid round.

’35 – ’40 Ford Double Chin BarThe two horizontal bars are made from 3/4” solid round with our V nerf bars. This may fit other makes of cars.

‘36-‘40 Ford Single Chin Bar WITHOUT Nerf BarsThis bar is made from 3/4” solid round stainless steel and designed to fit cars with filled bumper bracket holes. Our sleeve type brackets allow for maximum adjustability.

8 STACK INJECTION STYLEThis is a multi-stack injection looking air cleaner complete with filter element, mounting screw and base. Stacks are available in 6” or 8” tall or custom lengths.

8 STACK INJECTION STYLE STAGGEREDThe 8-stack injection air cleaner is available with 8” tall staggered stacks also. If you want something different, this one is for you.



CUSTOM BUMPERSBe it our design or yours, we will work with you to give your project a look you want while staying within your budget.




PAGE 12 PAGE 5

Be it our design or yours, we will work with you to give your project the look you want while staying within your budget.

715-387-6847

CUSTOM BUMPERS

NOTES

Our air cleaners are carefully formed from type 304 stainless steel, TIG welded, then polished to a mirror finish. These are our most popular designs but we are happy to custom build to your specifications.

Low profile, injection look “straight style”Built off our standard 14” long base, this unit features 8-2” flared stacks cut at a 45 degree angle to allow them to extend out parallel with top of air cleaner. Comes complete with filter, filter base, & mounting screw.

Low profile, injection look “STREAMLINE style”Also built off our standard 14” long base, this unit features 8-2” flared stacks cut at a 45 degree angle then evenly spaced and rotated to angle back giving the unit a “streamlined” look. Comes complete with filter, filter base, & mounting screw.

Air Cleaners




PAGE 12 PAGE 5


715-387-6847

CUSTOM BUMPERS

NOTES




Air Cleaners




PAGE 12 PAGE 5


715-387-6847

CUSTOM BUMPERS

NOTES




Air Cleaners



AIR CLEANERSOur air cleaners are carefully formed from type 304 stainless steel, TIG welded, then polished to a mirror finish. These are our most popular designs, but we are happy to custom build to your specifications.

Air Cleaners are made by special order. Please allow 3-4 weeks delivery.

8 STACK INJECTION STYLE $450

This is a multi-stack injection looking air cleaner complete with filter element, mounting screw and base. Stacks are available in 6” or custom lengths for an additional fee.

8 STACK INJECTION STYLE “STAGGERED” $470

The 8-stack injection air cleaner is available with 8” tall staggered stacks also. If you want something different, this one is for you.






PAGE 14 PAGE 3

MOTORCYCLE ACCENTS

HOOD SIDE VENTS









Bullet (pointed) Rolled Round Straight

HOOD SIDE VENTS

NOTES

Precision cut from 16 gauge stainless steel, these are fully functional vents and are designed to bolt on. Sold in pairs and available in single ($99/pair), double ($149/pair), or triple ($249/pair) designs. These also work well for interior accents and saddle bag trim.



For more pictures, go to www.mcmillanrodandcustom.com


M243 Highway T • Marshfield, WI 54449Phone: 715-387-6847 • Cell: 715-305-1069


www.mcmi l l anrodandcus tom.com

Fabricators of polished stainless steelcomponents for Hotrods and Customs.

CATALOG

DECIMAL EQUIVALENTS

COURTESY OF MCMILLAN ROD & CUSTOM


203160 County Road T • Marshfield, WI 54449Phone: 715-387-6847


Documents

DECIMAL EQUIVALENTS - McMillan Rod & Custom 2020.pdf · McMillan Rod & Custom M243 Highway T • Marshfield, WI 54449 Phone: 715-387-6847 • Cell: 715-305-1069 Email: [email protected]