SINGLE UNITModel PES-1X

TWO UNITS WITH GATEModel PES-DBLX

Printed in U.S.A.

97 Witmer RoadNorth Tonawanda, New York 14120-2421

Toll Free U.S. 800-635-3213 • FAX 716-694-3100www.conferladders.com

MADE IN THE USA

SAVE THESE INSTRUCTIONSDEALER/INSTALLER: GIVE TO HOMEOWNER

POOL ENTRY SYSTEMADJUSTS TO FIT 48” TO 54” POOLS AND DECKS

ASSEMBLY AND INSTALLATION MANUALAssembly video available online: www.conferplastics.com

WEIGHT LIMIT 400 LBS.

2

➀➁

➂

➃

➇

➆

➅

RISER GROOVE

FASTENINGFLANGE

RISERRECESS

Parts List

Code# Qty. Description CTN#

1 2 Side Panel 27 2 Anti-Entrapment Panel 28 4 Threaded Height Adjuster 2

(Factory Installed)

2 5 Step w/4 wedges 13 4 Riser 14 1 Kickplate 15 1 Deck Connector 16 2 Base 1

Hardware Pak

Qty. Description CTN#

3 1/4 - 20 Hex Nut 13 1/4 - 20 X 1” Screw 13 #10 x 1-1/4” Self Tapping Screw 12 Large Plug/Side Panels 11 Label for Top Riser 12 Threaded Cap 12 Red Plug 11 Instructions 11 Registration Card 1

Tools Required For Assembly

• Mallet or Hammer• Phillips Screwdriver• Cordless Drill Motor• 1/8” Drill Bit• Level• Hacksaw• Knife• Small Block of Wood• Tape Measure

Assembly InstructionsCONFER PLASTICS, INC. POOL ENTRY SYSTEM FOR ABOVE-GROUND POOLS

Adjusts to fit most above-ground pools with flat or slightly dished bottomsBill of Materials

➄

3

Step 2.Remove thewedges from everystep using a utilityknife. Do notdiscard.

Remove Wedges and SAVE.They will be needed in step 7

Step 3.

Lay the side panel on a clean flat surface. Firmlypush the protrusion of the steps into the opening ofthe handrail section. Insert the risers into thegrooves on the steps as shown above.

Step 4.

Continue adding steps and risers until all are firmlyin position.Note: position risers so center hole faces “back” ofsteps.

Step 5.

After determining the correct height from measurement#2 in step 1, cut the kickplate to the appropriateheight. Use a hacksaw to cut the ends (next to thepre-scored line) and a knife to separate the kickplateat the pre-scored line. Place the kickplate in positionbelow the bottom step.

Affix the warninglabel to center oftop riser.

The risers slip intogrooves on steps.

FOR DECK ATTACHMENT, MEASURE FROM HERE.

MEASURE FROM HERE FOR 2 UNITS ATTACHED (GROUND LEVEL ENTRY).TO ACCOUNT FOR THE POOLTOP SEAT, ADD 1/2" TO MEASUREMENTS.

MEASUREMENT #1

MEASUREMENT #2

8"

36"

WRITE MEASUREMENTS

MEASUREMENT #1 ______

MEASUREMENT #2 ______

1. Measure the Depth of Your Pool.A) For Deck Level Pool Entry (one (1) unit

attached to a deck), measure from the top of the deck to the bottom of the pool approxi-mately eight (8) inches out from the pool wall(Measurement #1). Take a second measure-ment approximately three (3) feet out from thepool wall (Measurement #2).

B) For Ground Level Pool Entry (two (2) unitsattached to each other), take the measure-ments from the top of the pool top seat. Addone-half (1/2) inch to these measurements forclearance.

*Whether you use method “A” or “B”, write yourmeasurements for future reference.

Step 1.

48" to 50", Cut Here50" to 52", Cut Here52" to 54", Cut Here

Protrusion

Opening

Step 6.

Step 9.

Use a mallet totap each baseonto the heightadjusters.

Step 11.

Attach the anti-entrapment panel (item 7) to both sides of the unit as shown. Position and push firmlydown into base until it locks securely into place.Note: Anti-Entrapment panels are not needed if the unit is left at 48".

Step 7.

Secure each step by tappinga locking wedge(saved from Step 2)between the sidepanel and the topsurface of the step protrusions.

Push the second side panel firmly down on the step protrusions. It may be necessary to tap the side panelusing a hammer and block of wood until seated correctly.

Push down firmly

Step 10.If you are fasteningthe pool entry systemto a deck: Attach thedeck connector to thetop step using thethree (3) 1/4-20x1"screws and hex nuts(nuts are installed onunderside of deckconnector).

4

Step 8.

On the bottom edgeof each side panel isa drain hole. Plugthese holes by firstinserting a (Red)plug into the holeand then coveringwith the threadedcap.

NOTE: If you are fasteningtwo units together, do notattach deck connector. Skipto Page 5 “Joining two PESPool Entry Systems”.

Red plug

Threaded cap

With a screwdriver, turn the heightadjusters to the desired height asdetermined in Step 1.

Proper exposed lengthis measurement #2minus 48-1/2"

To attach the base,position the unit asshown.

Proper exposed length is measurement #1 minus 48-1/2"

The maximumadjusted heightof the EntrySystem is (54 1/2) inches.

3 1/4-20 x 1" screws

3 hex nuts

5

Step 13.Step 12.

Carefully submerge the unit into the pool. Add water tothe side panels through the water fill openings locatednear the top of each side panel. When completely filled,press the supplied (white) plugs into the openings onboth side panels.

Water fillopeningson bothside panels.To preventalgae, adda cup ofhouseholdbleach(optional).

Step 14.

Joining two Pool Entry Systems.When joining two units together, the deck connectors will not be used.

Assemble both units and position the in-pool unitin the desired location, after filling it in the samemanner as step #12. Allow approximately two (2)inches of clearance between the side of the pool(pool liner) and the Entry System. Make any nec-essary height adjustments to ensure that all four(4) threaded adjustors are supporting the unit, thatthe unit is level and does not wobble, and that theunderside of the top step is about (1/2) inch above

the pool top seat. The outside unit should rest on cement patio blocks.Position and level the outside unit so that both units can be joinedusing the six (6) 1/4-20 x 1" machine screws and hex nuts. The hexnuts should be on the outside of the fastening flange of the side panels (See diagram on pg 2). Press the large plugs into the fill opening of the outside unit. It is not necessary to fill the outside unit with water.Note: Gate instructions and hardware are supplied with the gate.

Tilt the unit to allow the steps to fill with water. Whenbubbling ceases, steps are filled. Steps must be filledcompletely to prevent floating.

Note: Two people arerequired for this operation

Position the PES with attached deck connector and drillthree pilot holes. Attach to deck using 3 #10 x 1-1/4" SelfTapping Screws. Keep 2" clearance between unit andpool wall.

Attach with 3 #10 x 1-1/4" Self Tapping Screws

Safety Information1) Always follow the manufacturerʼs recommendations

for the safe use of all hand tools and equipment.

2) Always use a cordless drill.

3) Do not use the Pool Entry System for any purpose other than that for which it is intended.

4) When lifting awkward or heavy loads, haveanother person help you.

5) Maximum weight on steps not to exceed 400 lbs.

6) Consult your local building department beforeinstallation of your pool and equipment.

Warning: Exceeding the recommended weight requirement may cause the unit to fail.

Replacement Parts

Thank you for purchasing a C.P.I. product. Althoughwe make exceptional effort to ensure the quality ofour products, occasionally an error or omission mayoccur. If you discover that a part of this product ismissing or defective, please contact us for a replacement.

In The U.S.A. Call: (800) 635-3213or (716) 694-3100

Or Write To: Confer Plastics, Inc.

97 Witmer Road, North Tonawanda, NY 14120 U.S.A.

www.conferladders.com

Optional mounting method when deck height isgreater than (54-1/2) inches.Adjust the height of the entry system so that the topstep, at minimum, reaches the face board of the deck,however, the height of the bottom surface of the top stepmust not exceed (54-1/2) inches. Cut a piece of 2 x 4pressure treated lumber (28-1/4" long) and place it edgedown on the top step between the two flanges of theside panels. Secure in place with four #10 x 1-1/4"screws (not provided) through the two lower holes ineach of the mounting flanges of the side panel. Aftersecuring the 2 x 4 to the unit, position the unit so thatthe 2 x 4 meets the face board of the deck. It can thenbe secured in place using wood lag screws. Three 2-1/2"long lag screws are required (Lag screws not provided).

6

2" x 4" x 28-1/4" LONG

2-1/2" LONG LAG SCREWS

#10 x 1-1/4" LONG SELF-TAPPING SCREWS Order online @ www.conferladders.com

3-PESX-89APES-1X / PES-DBLX 5M 12/16

Removal and storage of Pool Entry System:In cold climates the Entry System must beremoved from the pool and drained to preventfreezing and cracking. To remove the unit discon-nect it from the deck (or the outside unit), pulllarge plugs and tip it so that some of the waterdrains from the large fill openings. Once the unitis lighter it will become buoyant so that it can beturned onto its side and the bottom drain capsand plugs can be removed. With the unit on itsside, slowly pull the Entry System from the waterallowing the water to drain out of the unit. Oncethe unit is out of the pool be sure that all thewater drains out. If desired the unit can be disas-sembled for winter storage. Use a flat bladescrewdriver to remove the locking wedges andcarefully pull the side panels away from the steps.(Be sure to save all caps and locking wedgesfor reassembly).

OPTIONAL ACCESSORY

SKIM-IT—SKIMS OFF DEBRIS. Cut cleaning time 75% with skimmer extensionthat guides debris directly into your skimmer. Fits most in-ground and above-ground poolskimmers. Corrosion-resistant plastic Skim-It

installs in seconds without tools.

DECK FACEBOARD

CONFER PLASTICS, INC. FIVE YEAR WARRANTYConfer Plastics, Inc. warrants their swimming pool ladders and steps to be free fromdefects in workmanship for five years from date of purchase.

DO NOT RETURN DEFECTIVE PART TO DEALERE-MAIL CONFER PLASTICS AT: LADDERS@CONFERPLASTICS.COM

A PICTURE [S] OF DEFECTIVE PART, A BRIEF DESCRIPTION OF PROBLEM, PROOF OF PURCHASE AND YOUR CONTACT INFORMATION.

INFORMATION MAY ALSO BE FAXED TO CONFER PLASTICS AT: 716-694-3102 OR MAILED TO THE ADDRESS BELOW. UPON REVIEW OF THE INFORMATION YOU

WILL BE NOTIFIED IF PART IS COVERED UNDER THE WARRANTY AND THE SHIPPING/HANDLING CHARGES.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Confer Plastics, Inc.97 Witmer Road

North Tonawanda, N.Y. 14120-2421