D:cno projectCNO RTDCNO RTD RTD... · 2015. 4. 23. · 1) Power Indication LED Red Power off Green Normal mode Red blinking Power saving mode or Check signal cable mode 2) MENU 1)

AD Board Specification

MODEL NAME:

CNO_RTD_REV36 Pages : 1/21

DATE : 2008/07/15

1. SCOPE …………………………………………………………………… 3

2. ENVIRONMENTAL and RELIABILITY SPECIFICATIONS

2.1 Operating Conditions ……………………………………………… 3

2.2 Storage Conditions ……………………………………………… 3

3. POWER AND INPUT SIGNAL

3.1 DC Input Power Requirements ……………………………… 3

3.2 PC Input Signal …………………………………………………… 4

3.3 VIDEO Input Signal …………………………………………… 5

4. USER CONTROL FUNCTIONS

4.1 User Control …………………………………………………… 6

4.2 OSD Structure (Analog RGB) ……………………………… 7

4.3 OSD Structure (VIDEO) ……………………………………… 8

4.4 OSD Process …………………………………………………… 9

4.5 OSD Message …………………………………………………… 13

5. ELECTRICAL CHARACTERISTICS

5.1 Operating Condition …………………………………………… 14

5.2 Test Condition …………………………………………………… 14

5.3 Power Management …………………………………………… 14

6. MICROPROCESSOR

6.1 Input Signal Recognition …………………………………… 15

6.2 Sync Range …………………………………………………… 15

6.3 Check Cable …………………………………………………… 15

6.4 Signal Recognition for Power Management ……………… 15

REFERENCE 1: CONNECTORS CONFIGURATION ……… 16

REFERENCE 2: BOARD DIMENSION ……………………………… 17

REFERENCE 3: WAFER CONNECTOR PIN-MAPPING ………… 18


MODEL NAME:Pages : 2/21

DATE : 2008/07/15

CNO_RTD_REV36

1. SCOPE

CNO_RTD_REV36 is an advanced TFT LCD Monitor Control Board. This design

enables a full conventional CRT monitor replacement with a large size Active

Matrix LCD module.

It is suitable for video resolution up to WUXGA@75Hz in all video modes, the

full display Area of the module is used. The design is implemented as a single

printed circuit board.

This CNO_RTD_REV36 is designed to act as a full monitor interface.

Besides the main functionality for a high resolution color monitor to be

operated in Analog input.

The CNO_RTD_REV36 is designed to support various TFT LCD modules under

WUXGA resolution by BIOS option, customers line-up their monitors with their

own identity with following options.

2. ENVIRONMENTAL and RELIABILITY SPECIFICATIONS

2.1 Operating Conditions

Temperature 0 ~ 50

Humidity 20% ~ 90%,(Ta ≤40), non-condensiong

2.2 Storage Conditions

Temperature -20 ~ 65

Humidity 5% ~ 90%,(Ta ≤40), non-condensiong

3. POWER AND INPUT SIGNAL

3.1 DC Input Power Requirements

Typical Input Voltage +12V DCInput Voltage Range +11.4 ~ 12.6V DCCurrent min 2.5A



DATE : 2008/07/15

CNO_RTD_REV36

3.2 PC Input Signal

Analog

Video Signal

1) Signal type R/G/B Analog

2) Gain level 0.714V ±5%3) Input impedance 75Ω ±5% (terminated)4) Pixel frequency max. 210MHz5) Resolution max. 1920x1200/75Hz

Input syncsignal(Analog)

1) Type H/V, Separate only

2) Gain levelTTL level(High ≥2.0V, Low ≤0.8V)

3) Polarity positive or negative4) Maximum Duty 25% max

5) Frequency RangeHorizontal 31~80 KHzVertical 56~75 Hz

Signal Connectors 15pin D-sub, angle type, fermale

* Signal Cable Pin Connection

PIN NO SIGNAL NAME REMARK1 RED SHIELDED2 GREEN SHIELDED3 BLUE SHIELDED4 N.C5 GROUND6 RED GND SHIELDED7 GREEN GND SHIELDED8 BLUE GND SHIELDED9 5V INPUT10 GROUND11 N.C12 SDA13 H-SYNC14 V-SYNC15 SCL



DATE : 2008/07/15

CNO_RTD_REV36

3.3 Video Input Signal

Video

Type NTSC

Output Level 1Vp-p (75ohms LOAD)Impedance 75ohmDiff. Amplification 10% MaxDiff. Phase 10 Degree MaxInput Connector (for CVBS) RCJ jack



DATE : 2008/07/15

CNO_RTD_REV36

4. USER CONTROL FUNCTIONS

4.1 User Control

1) Power Indication LED

Red Power offGreen Normal modeRedblinking

Power saving mode or Check signal cable mode

2) MENU1) Access to the OSD system2) With OSD off3) With OSD on, Choose the highlighted function

3) AUTO1) Input Source change, RGB, AV1, AV22) With OSD on, Select the highlighted function

4) POWER Turn off/on the display unit.

5) DOWN1) Move the cursor to down2) Decrease selected value3) With RGB mode, "AUTOADJUST"

6) UP1) Move the cursor to up2) Increase selected value3) If day/night enable, Select "day" or "night"



DATE : 2008/07/15

CNO_RTD_REV36

4.2 OSD Structure (Analog RGB)

Main Item Sub Item 1 Sub Item 2 Action

Analog

RGB

Color

Contrast Adjust the value of contrast

Brightness Adjust the value of brightness

Gamma Select gamma table

Color Temp Adjust color temperature value

Color Adjust

Red Adjust red color

Green Adjust green color

Blue Adjust blue color

Picture

H Position Adjust horizontal position of image

V Position Adjust vertical position of image

Phase Adjust phase of image

Clock Adjust clock of image

Sharpness Adjust sharpness of image

FunctionAuto Adjust Do tracking the image automatically

Auto Color Do white color balance automatically

OSD Menu

Language

English Select English

French Select French

German Select German

Spanish Select Spanish

Italian Select Italian

Korean Select Korean

OSD H Pos Adjust horizontal position of main menu

OSD V Pos Adjust vertical position of main menu

OSD Timer Adjust On-time of main menu

Translucent Adjust translucent of main menu

Misc

Signal Source

Analog Set input source to analog input

Composite

Video1Set input source to Composite Video1 input

Composite


Mode Select contrast mode

Reset Initialize the value of all item

Day/Night Select "day" or "night"

level Select brightness level



DATE : 2008/07/15

CNO_RTD_REV36

4.3 OSD Structure (Video)

Main Item Sub Item 1 Sub Item 2 Action

Video

Picture

Brightness Adjust the value of brightness

Contrast Adjust the value of contrast

Gamma Select gamma table

Color Temp Adjust color temperature value

Sharpness Adjust sharpness of image

VideoHue Adjust the value of Hue

Saturation Adjust the value of Saturation

Osd Menu

Language

English Select English

German Select German

French Select French

Italian Select Italian

Spanish Select Spanish

Korean Select Korean

OSD H Pos Adjust horizontal position of main menu

OSD V Pos Adjust vertical position of main menu

OSD Timer Adjust On-time of main menu

Translucent Adjust translucent of main menu

Utilities

Signal Source

Analog Set input source to analog input

Composite


Composite


Reset Initialize the value of all item

Day/Night Select "day" or "night"

level Select brightness level



DATE : 2008/07/15

CNO_RTD_REV36

4.4 OSD Process

1) Menu Key

If there is no main menu, main menu will show up, else main menu will be

disappeared.

Color

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Contrast

Brightness

Color Temp

Color Adjust

Color

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Contrast

Brightness

Color Temp

Color Adjust

2) Up Key / Down Key

Main cursor will move up and down.

Color

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

H.Position

V.Position

Phase

Clock

Color

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

H.Position

V.Position

Phase

Clock



DATE : 2008/07/15

CNO_RTD_REV36

3) Select Key

Sub cursor will show up.

Color

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Brightness

Color Temp

Color Adjust

ContrastColor

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Brightness

Color Temp

Color Adjust

Contrast


Sub cursor will move up and down.

Color

Picture

Function

OSD Menu

Misc.

1280x 60Hz

Brightness

Color Temp

Color Adjust

ContrastColor

Picture

Function

OSD Menu

Misc.

1280x 60Hz

Brightness

Color Temp

Color Adjust

Contrast



DATE : 2008/07/15

CNO_RTD_REV36

5) Select Key

Sub Item will be selected.

Color

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Brightness

Color Temp

Color Adjust

ContrastColor

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Brightness

Color Temp

Color Adjust

Contrast


The value of item is adjusted.

Color

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Brightness

Color Temp

Color Adjust

ContrastColor

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Brightness

Color Temp

Color Adjust

Contrast



DATE : 2008/07/15

CNO_RTD_REV36

7) MENU Key

OSD Menu will go back to previous status.

Color

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Brightness

Color Temp

Color Adjust

ContrastColor

Picture

Function

OSD Menu

Misc.

1280x1024 60Hz

Brightness

Color Temp

Color Adjust

Contrast



DATE : 2008/07/15

CNO_RTD_REV36

4.5 OSD Message

OUT OF RANGE

This message will show up when current input mode is out of range.

OUT OF RANGEOUT OF RANGE

NO SIGNAL

This message will show up when there is no input signal.

NO SIGNALNO SIGNAL

CHECK CABLE

This message will show up when the signal cable is not connected.

CHECK CABLECHECK CABLE



DATE : 2008/07/15

CNO_RTD_REV36

5. ELECTRICAL CHARACTERISTICS

5.1 Operating Condition

1) Ambient temperature 25 ±5

2) Brightness / Contrast Level control to maximum level

5.2 Test Condition

1) Warm up time ≥30min.2) AC supply voltage 12V ±5% / 60Hz3) Ambient temperature 25 ±5

4) Humidity 30% ~ 80%5) Display mode 1280 x 1024, 60Hz, Full white pattern

6) Brightness ControlFull brightness (backlight dimming)Set to distinguishable lower grey scales

7) Contrast ControlSet to default (OSD max. level), which allows that thebrightness two of 32 linear distributed grey scales (0-700mV)can be distinguished.

8) Black level ControlSet to default (OSD max. level), which allows that the darkesttwo of 32 linear distributed grey scales (0-700mV) can bedistinguished.

9) Input Signal 700 mVpp Analog Signal10) External Controls for picture position and dimensions

5.3 Power Management

Power On status

Normal Mode(Display mode)

less than 40W

Power Saving Mode(stand-by, suspend, off)

less than 1W Analog Signal



DATE : 2008/07/15

CNO_RTD_REV36

6. MICROPROCESSOR

6.1 Input Signal Recognition

1) Determine the polarity of horizontal and vertical sync (positive or negative).

2) If the horizontal and vertical polarities are same and the detected frequencies

are within the tolerance range (see below), the microprocessor recognizes

it as the same signal and load saved data from user mode.

3) Horizontal frequency tolerance : ±500 Hz

4) Vertical frequency tolerance : ±0.1 Hz

6.2 Sync Range

1) If input signal goes off the limited range, "NONE SUPPORTED" will appear

on the screen.

2) The limited range

- 26KHz ≤ Horizontal frequency ≤ 80KHz

- 56Hz ≤ Vertical frequency ≤ 75Hz

- 20MHz ≤ Dot Clock ≤ 140MHz

6.3 Check Cable

: When the cable is not connected with monitor, Check Cable icon will appear

on the screen.

6.4 Signal Recognition for Power Management

Power save mode (stand-by, suspend, power-off mode)

1) Horizontal frequency ＜ 10Khz,

2) Vertical frequency ＜ 40Hz maintain more than 10 seconds



DATE : 2008/07/15

CNO_RTD_REV36

REFERENCE 1: CONNECTORS CONFIGURATION



DATE : 2008/07/15

CNO_RTD_REV36

REFERENCE 2: BOARD DIMENSION



DATE : 2008/07/15

CNO_RTD_REV36

REFERENCE 3: WAFER CONNECTOR PIN-MAPPING

1) CNO_RTD_REV36 BOARD CONNECTOR

CONNECTOR

PART DISCRIPTION VENDORMATING

CONNECTOR

J9 SMAW200-10Wire-to-Board Wafer, Right Angle, 12PIN,2.0mm pitch, Mount

YEONHO SMH200-10

J8 FH-40S-0.5SH 0.5mm Pitch FFC Connector HIROSE

J1904-6298-006-000

-8830.5mm Pitch FFC Connector KYOCERA



DATE : 2008/07/15

CNO_RTD_REV36

2) J9 Connection - OSD_board

PIN NAME DISCRIPTION REMARK

1 GND Ground

2 UP Up_Key Active "LOW"

3 POWER Power_Key Active "LOW"

4 MENU Menu_Key Active "LOW"

5 DOWN Down_Key Active "LOW"

6 SEL Select_Key Active "LOW"

7 LED_G LED_Green

8 LED_R LED_Red

9 IR

10 VCC +5V

3) J19 Connection - LED Bcak-light


1 VLED-Anode1

2 VLED-Cathode1

3 VLED-Anode2

4 VLED-Cathode2

5 VLED-Anode3

6 VLED-Cathode3



DATE : 2008/07/15

CNO_RTD_REV36

4) J8 Connection - TFT-LCD


1 GND Ground

2 GND Ground

3 VCC System Power Supply

4 VCC System Power Supply

5 PD16 Red data 0

6 PD17 Red data 1

7 PD18 Red data 2

8 PD19 Red data 3

9 PD20 Red data 4

10 PD21 Red data 5

11 PD22 Red data 6

12 PD23 Red data 7

13 PD8 Green data 0

14 PD9 Green data 1

15 PD10 Green data 2






21 PD0 Blue data 0

22 PD1 Blue data 1

23 PD2 Blue data 2

24 PD3 Blue data 3

25 PD4 Blue data 4

26 PD5 Blue data 5

27 PD6 Blue data 6

28 PD7 Blue data 7

29 GND Ground

30 DOTCLK DOT CLOCK



DATE : 2008/07/15

CNO_RTD_REV36


31 PCI Display Mode *Note

32 HSYNC Horizontal Sync.

33 VSYNC Vertical Sync.

34 DE Data Enabling Signal

35 NC No Connect

36 NC No Connect

37 GND Ground

38 GND Ground

39 NC No Connect

40 NC No Connect

*Note : Regarding to the PCI, Please refer to the Power up/down sequence



DATE : 2008/07/15

CNO_RTD_REV36

Documents

D:cno projectCNO RTDCNO RTD RTD... · 2015. 4. 23. · 1) Power Indication LED Red Power off Green Normal mode Red blinking Power saving mode or Check signal cable mode 2) MENU 1)