Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
REVISION NO: 002PRODUCT DATA SHEET REPORT NO: 024
PRODUCT CODE: DA300
DAVIT ARM
024
For any technical queries please call our advice line on 0845 241 9102 3
AVIATOR DAVIT ARM
024
PRODUCT DESCRIPTION:The Aviator Davit Arm is designed to beremovable and to be used together with thepermanent Davit base plates. They are designedfor lifting and lowering personnel and materials. The hook on the end of the arm allows abseil and lifting ropes to extend over the roof edge or balustrading. The Davit base can also be used to anchor a personal fall arrest system when the user is being lifted and lowered. It is essential when designing rope access to ensure at least 2 abseil rope connection points (one for working line and the other for safety line) are available to connect to at any one time. Davit arms, up to 1m, are manufactured in aluminium section to ensure they are light weight and easily transportable. The davit arm is designed to fold to facilitate storage and transport.
In use
The Standard DA300 davit arm can be manufactured up to a height of 1500mm with a maximum reach of 850mm. It weighs approximately 15Kg. The arm can be locked into 2 positions – 135 degrees and 90 degrees off the vertical arm. The locking pin and clip are permanently fixed to the Davit arm to prevent them being mislaid.
Folded not in use
Removable
1.25m
0.8m
For any technical queries please call our advice line on 0845 241 91024
AVIATOR DAVIT ARM
024
900
SWL136Kg
For personnel
1350 SWL272Kg
For materials
only
Pulley
Handwinch
The DA300 Davit arm has a maximum safe working load of 136kg. This is a greater than 10:1 safety factor for personnel use and a greater than 5:1 safety factor for materials (272Kg). In the event of an emergency or for rescue situations 2 persons can use the Davit arm. The Davit arm can be supplied with a hand winch and pulley for material lifting. The Aviator Davit arms are designed and manufactured to fit into the Aviator Davit base plates. Never use the Aviator arm on any other make or model of Davit base or the system warranty will be invalidated
For any technical queries please call our advice line on 0845 241 9102 5
AVIATOR DAVIT ARM
024
MATERIAL SPECIFICATION:
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035;
S < 0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range
I-F Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel: 93 W/m°C
at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Davit armAluminium 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength 186MPa Yield strength 110MPa
Component parts and fixingsStainless Steel - Grade 304 (UNS S30400)Fe, <0.08% C, 17.5-20% Cr, 8-11% Ni, <2% Mn, <1% Si, <0.045% P, <0.03% Stainless Steel
Brackets - galvanised steel
Galvanised hand winch
Folding joint
Stainless steel rope guides
Stainless steel fixings
Aluminium arm
Aluminium locating spiggot
For any technical queries please call our advice line on 0845 241 91026
AVIATOR DAVIT ARM
024
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a Sayfa Systems Ltd, Aviator users course.
Courses are available from Sayfa Systems UK Ltd.
Courses cover the use of all Aviator and Payload products, the legal and practical side of the Working at Height legislation - 2005 and how to use and carry out safety checks on harnesses and all necessary PPE equipment.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers. Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
3Months
in harsh environments
d
12 Months
From date of installation
6Months
in harsh environments
d
CERTIFICATEOF
OPERATIVE INSTRUCTIONAL TECHNIQUES AND
WORKING AT HEIGHT SAFETY
In recognition of successful completion of training for the installation and assembly, use, handling and safety checks of:-
Aviator Safety Line Systems nAviator Mobile Anchors
Payload Access Ladder Systems
Payload Handrail Systems
Aviator PPE n
To:
........................................................................
Location of Training:
............................................................................0......................................................................
Certificate Number:
........................................................................
Name of trainee: ...................................................... Signed by trainee: .............................................
Inductor’s name: Adrian Stutterheim .................. Signed: Adrian Stutterheim ................................
Date of Training: 00 January 1900 .......................
For any technical queries please call our advice line on 0845 241 9102 7
AVIATOR DAVIT ARM
024
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN
British standards are designated by BS• BS/EN 795• Steel – EN10 113 and EN 10 025• BS 7985: 2013 Code of Practice for Rope Access
Methods for industrial purposes• The lifting operations and lifting equipment
regulations 1998• LOLER REG. 5(1) (a and b) for design• LOLER REG. 7(a, d and e) for marking• LOLER REG. 9 (1, 2 , 3 a and b) for examination• ISO 9001:2008, ISO14001:2004, BS OHSAS
18001:2007• Management of health and safety at work
regulations 1999 (MHSWR) ref.2• Work at height regulations 2005 (Ref 7)• Work at height (amended) regulations 2007 (Ref.8)
WAHR• BS ISO 22846 - 2 2012 Personal Equipment for
protection against falls code of practice• BS ISO 22846 - 1 : 2003 Personal Equipment for
protection against falls Fundamental principles for a system of work
• Provision and use of work equipment regulations 1999 PUWER 98 (Ref.5)
• The work at height safety association WAHSA- guidance on inspecting eyebolts for personal fall protection purposes
✔
BS ENISO
Standards
The company operates to the following standards
Typical connection loads (Maximum SWL 136kg for single user with a factor of safety greater than 10:1 with maximum davit arm cantilever of 0.8m)
Note: For guidelines only to be checked by Chief Engineer
Table of bracket moments
12kN for 800mm arm
15kN for 1000mm arm
18kN for 1200mm arm
22.5kN for 1500mm arm
In Use
ULS15kN
For any technical queries please call our advice line on 0845 241 91028
AVIATOR DAVIT ARM
024
COMPONENT PART DETAILS:Davit arm personnel use DA300 BIM No: SpecEquip_RfSftySymDvtArm_SayfaSystems_DA300_
M3_G2
Davit arm materials lifting DA400 BIM No: SpecEquip_RfSftySymDvtArm_SayfaSystems_DA400_
M3_G2
Winch Bracket DAWB01BIM No: SpecEquip_RfSftySymDvtArmWnchBkt_SayfaSystems_
DAWB01_M3_G2
Material Lifting Folding Aluminium Davit Arm DA500
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA500
Mark.S CS 13/04/2017
D
Designed by Checked by Approved by Date
1 / 7 Edition Sheet
Date
DA500Material Lifting Folding Aluminium
Davit Arm
Portable
Folded
135 Degrees
90 Degrees
R T
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA300
Mark.S MW 10/06/2015
B
Designed by Checked by Approved by Date
1 / 4 Edition Sheet
Date
DA300Single User Folding Aluminium
Davit Arm
Portable
Folded
135 Degrees
90 Degrees
R T
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA300
Mark.S MW 10/06/2015
B
Designed by Checked by Approved by Date
1 / 4 Edition Sheet
Date
DA300Single User Folding Aluminium
Davit Arm
Portab
le
Fold
ed
135
Degr
ees
90 D
egre
es
R
T
1 1
2 2
3 3
4 4
5 5
6 6
AA
BB
CC
DD
Fold
ing
Davit
Arm
DA30
0
Mar
k.S
MW
10/0
6/20
15
B
Desig
ned
byCh
ecke
d by
Appr
oved
by
Date
1 / 4
Ed
ition
Shee
t
Date
DA3
00Si
ngle
Use
r Fol
ding
Alu
min
ium
D
avit
Arm 135 Degrees
Portable
90 Degrees
Folded
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA400
Mark.S MW 10/06/2015
C
Designed by Checked by Approved by Date
1 / 7 Edition Sheet
Date
DA400Material Lifting Folding Aluminium
Davit Arm
135 Degrees
Portable
90 Degrees
Folded
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA400
Mark.S MW 10/06/2015
C
Designed by Checked by Approved by Date
1 / 7 Edition Sheet
Date
DA400Material Lifting Folding Aluminium
Davit Arm
135 Degrees
Portable
90 Degrees
Folded
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA400
Mark.S MW 10/06/2015
C
Designed by Checked by Approved by Date
1 / 7 Edition Sheet
Date
DA400Material Lifting Folding Aluminium
Davit Arm
135
Deg
rees
Portable
90 D
egre
es
Fold
ed
1 1
2 2
3 3
4 4
5 5
6 6
AA
BB
CC
DD
Fold
ing
Dav
it Ar
m
DA4
00
Mar
k.S
MW
10/0
6/20
15
C
Des
igne
d by
Chec
ked
byAp
prov
ed b
yD
ate
1 /
7 Ed
ition
Shee
t
Dat
e
DA
400
Mat
eria
l Lif
ting
Fol
ding
Alu
min
ium
D
avit
Arm
Portable
Folded
135 Degrees
90 Degrees
R T
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA300
Mark.S MW 10/06/2015
B
Designed by Checked by Approved by Date
1 / 4 Edition Sheet
Date
DA300Single User Folding Aluminium
Davit Arm
Portable
Folded
135 Degrees
90 Degrees
R T
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA300
Mark.S MW 10/06/2015
B
Designed by Checked by Approved by Date
1 / 4 Edition Sheet
Date
DA300Single User Folding Aluminium
Davit Arm
1
1
2
2
3
3
4
4
5
5
6
6
A A
B B
C C
D D
Folding Davit Arm
DA500
Mark.S CS 13/04/2017
D
Designed by Checked by Approved by Date
1 / 7 Edition Sheet
Date
DA500Material Lifting Folding Aluminium
Davit Arm
For any technical queries please call our advice line on 0845 241 9102 9
AVIATOR DAVIT ARM
024
Aviator™ Da300/Da400 Fixed To Cast Concrete Slab With Parapet Wall
MOUNTING HOLESTO SECURE DAVIT ARMTO DAVIT BASE WITH 8M16 BOLTS
8NR M16 BOLTS RESIN FIXEDINTO CONCRETE SLAB
PITCH POCKET WEATHERING(RECOMMENDED) BY ROOFINGCONTRACTOR
DB400GALVANIZED STEELBRACKET 150-350mm
DA300/400ALUMINUM FOLDING ARMWEIGHT 35kg Approximately
DAWDAVIT ARM WINCHONLY SUITABLE FOR USEWITH DA400 - MATERIALSLIFTING DAVIT ARM
· Bases to be located as indicated on theroof plan.
· Arm primarily used to gain access toexposed facades.
· Incorporates Aviator™ units and allSayfa Systems components required.
· Fixing details for Aviator™ units asindicated within layout.
· Structural Engineer to confirmsubstructure can wistand LSD12-15kN. SLD 4-6kN of post/davit.
System Details
Jubilee House
ShepshedLeicestershireLE12 9NHT:01509 502 155F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
UNDER THE CDM REGULATIONS 2015, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
THIS DRAWING WAS CREATED INCONJUNCTION WITH N/A
DRAWING NO. N/A
DRAWING REVISIONS
REV BY DATE COMMENTS
A M.W 07/09/2015 Issued forinternal review
B C.S 26/06/2018 Part No.s added
Client:
Contract:
Project Title:
SAYFA SYSTEMS UKLIMITED
FIXING DETAILS
AVIATOR™ DA300/DA400FIXED TO CAST CONCRETESLAB WITH PARAPET WALL
Revision:
Drawn By:
Scale:
Date:
Checked By:
Job No:
DWG No:
Status:
Released By:
N/A
N/A
B
C.S
FOR DESIGN
1:12 @ A3
26/06/2018
M.S
For any technical queries please call our advice line on 0845 241 910210
AVIATOR DAVIT ARM
024
Aviator™ Da500 Davit Arm Fixed To Cast Concrete Slab With Parapet Wall
MOUNTING HOLESTO SECURE DAVIT ARMTO DAVIT BASE WITH 8M16 BOLTS
8NR M16 BOLTS RESIN FIXEDINTO CONCRETE SLAB
PITCH POCKET WEATHERING(RECOMMENDED) BY ROOFINGCONTRACTOR
DB400GALVANIZED STEELBRACKET 150-350mm
DA500ALUMINUM FOLDING ARMWEIGHT
DAWDAVIT ARM WINCH(OPTIONAL)
· Bases to be located as indicated on theroof plan.
· Arm primarily used to gain access toexposed facades.
· Incorporates Aviator™ units and allSayfa Systems components required.
· Fixing details for Aviator™ units asindicated within layout.
· Structural Engineer to confirmsubstructure can wistand LSD12-15kN. SLD 4-6kN of post/davit.
System Details
Jubilee House
ShepshedLeicestershireLE12 9NHT:01509 502 155F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
UNDER THE CDM REGULATIONS 2015, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
THIS DRAWING WAS CREATED INCONJUNCTION WITH N/A
DRAWING NO. N/A
DRAWING REVISIONS
REV BY DATE COMMENTS
A C.S 26/06/2018 Issued forinformation
Client:
Contract:
Project Title:
SAYFA SYSTEMS UKLIMITED
FIXING DETAILS
AVIATOR™ DA500 DAVIT ARMFIXED TO CAST CONCRETESLAB WITH PARAPET WALL
Revision:
Drawn By:
Scale:
Date:
Checked By:
Job No:
DWG No:
Status:
Released By:
N/A
N/A
A
C.S
FOR DESIGN
1:12 @ A3
26/06/2018
M.S
Sayfa Systems UK LtdJubilee HouseNo. 3 Gelders Hall RoadShepshed, LoughboroughLeicestershire LE12 9NH
T: 0845 241 9102F: 0845 130 4520email: [email protected]
Ref: 125/024-11/18