Upload
kovacs-tamas
View
250
Download
5
Embed Size (px)
Citation preview
2
The contents enclosed in this catalogue define a policy of sound commercialpractice, but also accept that legislation covering the performance of productsis increasing. With the introduction of BS EN ISO 9000 there is a greater tendency for large purchasers to buy from suppliers who have registered quality systems.Therefore the increasing concern for quality must reflect in our company’s products themselves. The relevant back up documentation is an important application of the qualityrequirement and it is our company’s policy to provide this with all its products.
A strict adherence to all aspects of our company’s policies and proceduresinvolves the total workforce which has been educated to meet these demands.
Standards and ServicesDirected by our BS EN ISO 9000 registration, Batch Testing and Practicability
Procedures are incorporated into the Standard Davico practices, and the majority of
the products contained in this catalogue are tested to meet most International
Standard requirements internally or externally.
What is Quality?Quality as expected by Davico employees is defined in the following eight points:
• Knowing the customer’s needs and expectations
• Faultless construction
• Certified performance and safety
• Clear instruction manuals
• Punctual delivery
• Efficient back-up services
• Feedback of field experience
• Value for money
The Quality ManualThe Davico Quality Manual is an effective way of promoting recognition of quality
throughout the company.
It demonstrates the company’s ability to operate an efficient quality assurance
system which will result in preventing the supply of inferior goods and services.
Certificates of Conformity are essential when complying with BS EN ISO 9000
requirements. Submission of these is again a major function of the Davico
organisation and creates customer confidence in the products.
Introduction
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1 3
Technical SupportWith the introduction of new and continuing changes to National Standards and
Specifications on performance and characteristics of product, new methods and
improved procedures are being evolved to achieve this end. This takes into
consideration all safety parameters of the product application.
Should you require any additional information regarding product specification or
application please contact our office: expert technical advice is always available,
either via telephone or an onsite visit from our sales engineers.
The Case for MaintenanceThe most important means of measuring quality is at the hands of the customer.
Many products are sold to distributors, agencies and manufacturing organisations
and it is with this in mind that our company will contract to repair and service all
equipment supplied. The company management has developed an efficient system
of two way information.
To ensure customer satisfaction under this system and together with the
maintenance procedures it is essential that tool calibration is conducted in
accordance with the directives of BS EN ISO 9000 and other International Standards.
On this basis the necessary documented evidence is provided to ensure a
meaningful relationship between our company and our customers.
Service and Field InformationAs part of the maintenance system Davico implements the following five
procedures:
• Monitored policy on servicing
• Methods of feedback of field information to all relevant company departments
• Methods of supplying up-to-date information to company field staff and
customers
• Procedure for handling customer complaints and return of goods
• Procedures for handling incoming supplies
Tool Check and CalibrationIt is very important that tooling compression is monitored regularly. Checks are
conducted together with go and no-go gauge tolerancing. These should be
implemented at a minimum of one check per year, and possibly more dependant on
the number of tools in service. Correct calibration is an important function of
meeting National Standards for service and maintenance.
MaintenanceThe maintenance procedures are implemented as detailed in the Davico Quality
Manual. All hand and hydraulic tools can be serviced or repaired in accordance with
the requirement. Service checks include for replacement of oil seals, reservoirs, stops
etc. Service reports are available and on completion Certificates of Conformity of
Service are issued.
Introduction
6
No 1 TERMINALS (INSULATED)
LD Terminals • Hand Tools • Accessories
Pin
Flanged Fork
Hooked Blade
Ring Blade
Part Dimensions mm Stud
Number d D L Size mm
DVR 1-3 3.2 5.7 17.3 3.0
DVR 1-3L 3.2 8.0 21.0 3.0
DVR 1-3.7 3.7 5.7 21.0 3.5
DVR 1-3.7L 3.7 6.6 21.0 3.5
DVR 1-4 4.3 6.6 19.6 4.0
DVR 1-4L 4.3 8.0 21.0 4.0
DVR 1-5 5.3 8.0 21.0 5.0
DVR 1-6 6.4 11.6 27.0 6.0
DVR 1-8 8.4 11.6 27.0 8.0
DVR 1-10 10.5 13.6 31.1 10.0
DVR 1-12 13.0 19.3 38.0 12.0
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 1, DHCR 15,
DBMT 1, 3 & 4.
Part Dimensions mm Stud
Number d D L Size mm
DVF 1-3 3.2 5.7 21.2 3.0
DVF 1-3N 3.7 6.4 21.2 3.5
DVF 1-3W 3.7 7.2 21.2 3.5
DVF 1-4N 4.3 6.4 21.2 4.0
DVF 1-4 4.3 7.2 21.2 4.0
DVF 1-4W 4.3 8.1 21.2 4.0
DVF 1-5 5.3 9.5 21.2 5.0
DVF 1-6 6.4 12.0 27.7 6.0
Part Dimensions mm Stud
Number d D L Size mm
DVF 1-3F 3.7 7.6 23.7 3.5
DVF 1-4F 4.3 7.6 23.7 4.0
DVF 1-5F 5.3 8.5 23.7 5.0
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 1, DHCR 15,
DBMT 1, 3 & 4.
Part Dimensions mm
Number D W L
DVB 1-10 10.4 2.3 19.4
DVB 1-18 18.4 2.3 27.5
DVB 1-11 11.1 3.0 20.1
DVB 1-14 14.5 3.0 23.5
Part Dimensions mm
Number D W L
DVB 1-13H 13.0 3.0 27.2
DVB 1-17H 16.75 4.6 28.2
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 1, DHCR 15, DBMT 1, 3 & 4.
Part Dimensions mm
Number D W L
DVP 1-9 1.9 9.0 18.5
DVP 1-12 1.9 12.0 21.2
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 1, DHCR 15, DBMT 1, 3 & 4.
Also available with twin grip copper sleevesupport. When ordering add TG to Part No.i.e DVR 1-4TG.
Conductor Sizes: 0.25–1.65mm2 22–16 AWGSingle Strand: 0.57–1.44 Dia.
For high temperature applications Davico cansupply an insulated Makrolon terminal witha working temperature of –40°C to 125°C.
Fork
Davico Terminals aredesigned for easy entryapplication as indicated.
Red Vinyl Red Vinyl Red Vinyl
Red Flared Vinyl
Red Vinyl
Red Vinyl
7
No 1 TERMINALS (NON INSULATED)
LD Terminals • Hand Tools • Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Pin
Flanged Fork
Hooked Blade
Ring Fork Blade
Part Dimensions mm Stud
Number d D L Size mm
DR 1-3 3.2 5.7 12.6 3.0
DR 1-3L 3.2 8.0 15.8 3.0
DR 1-3.7 3.7 5.7 12.6 3.5
DR 1-3.7L 3.7 6.6 15.8 3.5
DR 1-4 4.3 6.6 14.4 4.0
DR 1-4L 4.3 8.0 15.8 4.0
DR 1-5 5.3 8.0 15.8 5.0
DR 1-6 6.4 11.6 21.8 6.0
DR 1-8 8.4 11.6 21.8 8.0
DR 1-10 10.5 13.6 25.5 10.0
DR 1-12 13.0 19.3 31.0 12.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 1510,
DHCR 1516, DBMT 1, 3 & 4.
Part Dimensions mm Stud
Number d D L Size mm
DF 1-3 3.2 5.7 16.0 3.0
DF 1-3N 3.7 6.4 16.0 3.5
DF 1-3W 3.7 7.2 16.0 3.5
DF 1-4N 4.3 6.4 16.0 4.0
DF 1-4 4.3 7.2 16.0 4.0
DF 1-4W 4.3 8.1 16.0 4.0
DF 1-5 5.3 9.5 16.0 5.0
DF 1-6 6.4 12.0 22.0 6.0
Part Dimensions mm Stud
Number d D L Size mm
DF 1-3F 3.7 7.6 13.1 3.5
DF 1-4F 4.3 7.6 13.1 4.0
DF 1-5F 5.3 8.5 13.1 5.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 1510, DHCR 1516,
DBMT 1, 3 & 4.
Part Dimensions mm
Number D W L
DB 1-10 10.4 2.3 15.2
DB 1-18 18.4 2.3 23.2
DB 1-11 11.1 3.0 15.9
DB 1-14 14.5 3.0 19.3
Part Dimensions mm
Number D W L
DB 1-13H 13.0 3.0 23.0
Suitable crimping tools:
DHC 15, DHCR0516, DHCR 1510, DHCR 1516,
DBMT 1, 3 & 4.
Part Dimensions mm
Number D W L
DP 1-9 1.9 9.0 14.3
DP 1-12 1.9 12.0 17.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 1510, DHCR 1516,
DBMT 1, 3 & 4.
Conductor Sizes: 0.25–1.65mm2 22–16 AWGSingle Strand: 0.57–1.44 Dia.
8
No 2 TERMINALS (INSULATED)
Blade
LD Terminals • Hand Tools • Accessories
Ring
Part Dimensions mm Stud
Number d D L Size mm
DVR 2-3 3.2 6.6 17.3 3.0
DVR 2-3L 3.2 8.5 22.0 3.0
DVR 2-3.7 3.7 6.6 17.3 3.5
DVR 2-3.7L 3.7 6.6 22.0 3.5
DVR 2-4 4.3 6.6 19.6 4.0
DVR 2-4L 4.3 8.5 22.0 4.0
DVR 2-5 5.3 8.5 22.0 5.0
DVR 2-5L 5.3 9.5 22.0 5.0
DVR 2-6 6.4 12.0 27.1 6.0
DVR 2-8 8.4 12.0 27.1 8.0
DVR 2-10 10.5 13.6 29.7 10.0
DVR 2-12 13.0 19.0 35.2 12.0
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 2,
DHCR 15, DBMT 1, 3 & 4.
Pin
Hooked Blade
Part Dimensions mm
Number D W L
DVB 2-9 9.0 2.8 17.7
DVB 2-18 18.4 2.3 27.4
Part Dimensions mm
Number D W L
DVB 2-13H 13.0 3.0 27.2
DVB 2-17H 16.75 4.6 27.2
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 2, DHCR 15, DBMT 1, 3 & 4.
Part Dimensions mm
Number D W L
DVP 2-9 1.9 9.0 18.5
DVP 2-12 1.9 12.0 21.2
Suitable crimping tools: DHC 15, DHC 15Y, DHCR 2,
DHCR 1, 3 & 4.
Flanged Fork
Fork
Part Dimensions mm Stud
Number d D L Size mm
DVF 2-3 3.2 5.7 21.2 3.0
DVF 2-3N 3.7 6.4 21.2 3.5
DVF 2-3W 3.7 7.2 21.2 3.5
DVF 2-4N 4.3 6.4 21.2 4.0
DVF 2-4 4.3 7.2 21.2 4.0
DVF 2-4W 4.3 8.1 21.2 4.0
DVF 2-5 5.3 9.5 21.2 5.0
DVF 2-6 6.4 12.0 27.7 6.0
Part Dimensions mm Stud
Number d D L Size mm
DVF 2-3F 3.7 7.6 23.7 3.5
DVF 2-4F 4.3 7.6 23.7 4.0
DVF 2-5F 5.3 8.5 23.7 5.0
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 2, DHCR 15, DBMT 1,
3 & 4.
Blue Vinyl
Blue Vinyl
Blue Flared Vinyl
Blue VinylBlue VinylBlue Vinyl
Also available with twin grip copper sleevesupport. When ordering add TG to Part No.i.e DVR 2-4TG.
For high temperature applications Davico cansupply an insulated Makrolon terminal witha working temperature of –40°C to 125°C.
Davico Terminals aredesigned for easy entryapplication as indicated.
Conductor Sizes: 1.04–2.63mm2 16–14 AWGSingle Strand: 1.14–1.82 Dia.
9
Pin
Flanged Fork
Hooked Blade
No 2 TERMINALS (NON INSULATED)
LD Terminals • Hand Tools • Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Ring Fork Blade
Part Dimensions mm Stud
Number d D L Size mm
DR 2-3 3.2 6.6 12.3 3.0
DR 2-3L 3.2 8.5 16.8 3.0
DR 2-3.7 3.7 6.6 16.8 3.5
DR 2-3.7L 3.7 6.6 16.8 3.5
DR 2-4 4.3 6.6 14.4 4.0
DR 2-4L 4.3 8.5 16.8 4.0
DR 2-5 5.3 8.5 16.8 5.0
DR 2-5L 5.3 9.5 16.8 5.0
DR 2-6 6.4 12.0 21.8 6.0
DR 2-8 8.4 12.0 21.8 8.0
DR 2-10 10.5 13.6 25.5 10.0
DR 2-12 13.0 19.0 31.0 12.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 1510,
DHCR 1516, DBMT 1, 3 & 4.
Part Dimensions mm Stud
Number d D L Size mm
DF 2-3 3.2 5.7 14.5 3.0
DF 2-3N 3.7 6.4 15.4 3.5
DF 2-3W 3.7 7.2 16.0 3.5
DF 2-4N 4.3 6.4 15.4 4.0
DF 2-4 4.3 7.2 16.0 4.0
DF 2-4W 4.3 8.1 16.8 4.0
DF 2-5 5.3 9.5 16.8 5.0
DF 2-6 6.4 12.0 22.0 6.0
Part Dimensions mm Stud
Number d D L Size mm
DF 2-3F 3.7 7.6 14.0 3.5
DF 2-4F 4.3 7.6 14.0 4.0
DF 2-5F 5.3 8.5 14.0 5.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 1510, DHCR 1516,
DBMT 1, 3 & 4.
Part Dimensions mm
Number D W L
DB 2-9 9.0 2.8 13.3
DB 2-18 18.4 2.3 23.2
Part Dimensions mm
Number D W L
DB 2-13H 13.0 3.0 23.0
Suitable crimping tools:
DHC 15, DHCR0516, DHCR 1510, DHCR 1516, DBMT 1,
3 & 4.
Part Dimensions mm
Number D W L
DP 2-9 9.0 1.9 14.3
DP 2-12 12.0 1.9 17.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 1510, DHCR 1516,
DBMT 1, 3 & 4.
Conductor Sizes: 1.04–2.63mm2 16–14 AWGSingle Strand: 1.14–1.82mm Dia
10
No 5 TERMINALS (INSULATED)
Ring Fork
Pin
Blade
LD Terminals • Hand Tools • Accessories
Part Dimensions mm Stud Size
Number d D L mm
DVR 5-3 3.2 7.2 20.9 3.0
DVR 5-3.7 3.7 7.2 20.9 3.5
DVR 5-4 4.3 7.2 20.9 4.0
DVR 5-4L 4.3 9.5 25.0 4.0
DVR 5-5 5.3 9.5 25.0 5.0
DVR 5-5L 5.3 12.0 31.0 5.0
DVR 5-6 6.4 12.0 31.0 6.0
DVR 5-6L 6.4 15.0 33.2 6.0
DVR 5-8 8.4 12.0 33.2 8.0
DVR 5-8L 8.4 15.0 33.2 8.0
DVR 5-10 10.5 15.0 33.2 10.0
DVR 5-12 13.0 19.2 37.6 12.0
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 5, DHCR 15,
DBMT 1, 3 & 4.
Part Dimensions mm Stud Size
Number d D L mm
DVF 5-3 3.2 8.3 25.2 3.5
DVF 5-4 4.3 8.3 25.2 4.0
DVF 5-4W 4.3 9.0 23.9 4.0
DVF 5-5 5.3 9.0 23.9 5.0
DVF 5-6 6.4 12.0 31.2 6.0
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR 5, DHCR 15,
DBMT 1, 3 & 4
Part Dimensions mm
Number W D L
DVB 5-10 2.8 10.0 20.4
DVB 5-14 4.5 14.0 26.0
Part Dimensions mm
Number W D L
DVP 5-14 2.9 14.0 27.2
Suitable crimping tools:
DHC 15, DHC 15Y, DHCR5, DHCR 15,
DBMT 1, 3 & 4
Yellow Vinyl
Yellow Vinyl
Yellow VinylYellow Vinyl
Also available with twin grip copper sleevesupport. When ordering add TG to Part No.i.e DVR 5-4TG.
Conductor Sizes: 2.63–6.64mm2 12–10 AWGSingle Strand: 1.82–2.89 Dia.
For high temperature applications Davico cansupply an insulated Makrolon terminal witha working temperature of –40°C to 125°C.
Davico Terminals aredesigned for easy entryapplication as indicated.
Hooked Blade
Part Dimensions mm
Number D W L
DVB 5-13H 3.0 17.2 30.2
DVB 5-17H 4.6 17.2 30.2
Yellow Flared Vinyl
11
Ring Fork
Pin
No 5 TERMINALS (NON INSULATED)
LD Terminals • Hand Tools • Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Part Dimensions mm Stud Size
Number d D L mm
DR 5-3 3.2 7.2 15.7 3.0
DR 5-3.7 3.7 7.2 15.7 3.5
DR 5-4 4.3 7.2 15.7 4.0
DR 5-4L 4.3 9.5 19.8 4.0
DR 5-5 5.3 9.5 19.8 5.0
DR 5-5L 5.3 12.0 25.8 5.0
DR 5-6 6.4 12.0 25.8 6.0
DR 5-6L 6.4 15.0 28.0 6.0
DR 5-8 8.4 15.0 28.0 8.0
DR 5-8L 8.4 15.0 28.0 8.0
DR -10 10.5 15.0 28.0 10.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 15N, DHCR 1510,
DBMT 1, 3 & 4.
Part Dimensions mm Stud Size
Number d D L mm
DF 5-3 3.2 8.3 19.5 3.5
DF 5-4 4.3 8.3 19.5 4.0
DF 5-4W 4.3 9.0 18.2 4.0
DF 5-5 5.3 9.0 18.2 5.0
DF 5-6 6.4 12.0 25.5 6.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 15N, DHCR 1510,
DBMT 1, 3 & 4.
Part Dimensions mm
Number W D L
DB 5-10 2.8 10.0 16.2
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 15N, DHCR 1510,
DBMT 1, 3 & 4.
Part Dimensions mm
Number W D L
DB 5-14 2.9 14.0 20.0
Suitable crimping tools:
DHC 15, DHCR 0516, DHCR 15N, DHCR 1510,
DBMT 1, 3 & 4.
Blade
Conductor Sizes: 2.63–6.64mm2 12–10 AWGSingle Strand: 1.82–2.89mm Dia.
12
CONNECTORS (INSULATED AND NON INSULATED)
LD Terminals • Hand Tools • Accessories
Parallel (Insulated)
Butt (Non Insulated)
Parallel (Non Insulated)
Butt (Insulated)
Closed End (Insulated)
Conductor Sizes: Red 0.25–1.65mm2 Blue 1.04–2.63mm2 Yellow 2.63–6.64mm2
Part Dimensions mm Vinyl
Number d D L Colour
DVPC1 1.7 3.3 16.0 Red
DVPC2 2.3 4.0 16.0 Blue
DVPC5 3.4 5.5 20.5 Yellow
Part Dimensions mm Vinyl
Number d D L Colour
DVBC1 1.7 3.3 22.7 Red
DVBC2 2.3 4.0 22.7 Blue
DVBC5 3.4 5.5 26.7 Yellow
Suitable crimping tools:
Red: DHC 15, DHC 1 5Y, DHCR 1, DHCR 15,
DBMT 1, 3 & 4.
Blue: DHC 15, DHC 15Y, DHCR 2, DHCR 15,
DBMT 1, 3 & 4.
Yellow: DHC 15, DHC 15Y, DHCR 5, DHCR 15,
DBMT 1, 3 & 4.
Part Dimensions mm Conductor
Number d D L Size mm2
DN 1-CEC 4.9 6.4 15.3 1.0–1.75
DN 2-CEC 5.7 6.6 15.3 1.0–2.5
DN 5-CEC 7.2 9.4 17.7 2.0–5.5
Suitable crimping tools:
DHCR-HS, DHC 15, DHCR 15, DBMT 1, 3 and 4.
Part Dimensions mm
Number d D L
DPC1 1.7 3.3 8.0
DPC2 2.3 4.0 8.0
DPC5 3.4 5.5 8.5
Part Dimensions mm
Number d D L
DBC1 1.7 3.3 15.0
DBC2 2.3 4.0 15.0
DBC5 3.4 5.5 15.0
13
Female Female
Female
PUSH ON TERMINALS (INSULATED AND NON INSULATED)
LD Terminals • Hand Tools • Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Male
Part Conductor To Suit Colour
Number Size mm2 width mm
DVPO1-2.8F5 0.25–1.65 2.8 x 0.5 Red
DVPO1-2.8F8 0.25–1.65 2.8 x 0.8 Red
DVPO1-4.8F5 0.25–1.65 4.8 x 0.5 Red
DVPO1-4.8F8 0.25–1.65 4.8 x 0.8 Red
DVPO1-6.3F 0.25–1.65 6.3 Red
DVPO2-4.8F5 1.04–2.63 4.8 x 0.5 Blue
DVPO2-4.8F8 1.04–2.63 4.8 x 0.8 Blue
DVPO2-6.3F 1.04–2.63 6.3 Blue
DVPO2-8.0F 1.04–2.63 8.0 x 0.8 Blue
DVPO5-6.3F 2.63–6.64 6.3 Yellow
DVPO5-9.5F 2.63–6.64 9.5 Yellow
Suitable crimping tools:
Red: DHC 15, DHC 15Y, DHCR 1, DHCR 15, DBMT
1, 3 &4
Blue: DHC 15, DHC 15Y, DHCR 2, DHCR 15, DBMT
1, 3 & 4
Yellow: DHC 15, DHC 15Y, DHCR 5, DHCR 15,
DBMT 1, 3 & 4
Part Conductor To Suit Colour
Number Size mm2 width mm
*DNFP01-2.8F5 0.25-1.65 2.8 x 0.5 Red
*DNFP01-2.8F8 0.25-1.65 2.8 x 0.8 Red
DVFP01-4.8F5 0.25-1.65 4.8 x 0.5 Red
DVFP01-4.8F8 0.25-1.65 4.8 x 0.8 Red
DVFP01-6.3F 0.25-1.65 6.3 Red
DVFP02-4.8F5 1.04-2.63 4.8 x 0.5 Blue
DVFP02-4.8F8 1.04-2.63 4.8 Blue
DVFP02-6.3F 1.04-2.63 6.3 Blue
DVFP05-6.3F 2.63-6.64 6.3 Yellow
DVFP05-9.5F 2.63-6.64 6.3 Yellow
*DNFPO Nylon Insulated
Part Conductor To Suit
Number Size mm2 width mm
DP01-2.8F5 0.25 1.65 2.8 x 0.5
DP01-2.8F8 0.25 1.65 2.8 x 0.8
DP01-4.8F5 0.25 1.65 4.8 x 0.5
DP01-4.8F8 0.25 1.65 4.8 x 0.8
DP01-6.3F 0.25 1.65 6.3
DP02-4.8F5 1.04 2.63 4.8 x 0.5
DP02-4.8F8 1 04 2.63 4.8 x 0.8
DP02-6.3F 1.04 2.63 6.3
DP05-6.3F 2.63 6.64 6.3
DP05-9.5F 2.63 6.64 9.5
Suitable crimping tools:
DHCF 15, DHCRF 15, DBMT 1, 3 & 4.
Part Dimensions mm Conductor Colour
Number W T L Size mm2
DVPO 1-4.8M 4.75 0.8 9.5 0.25 x 1.65 Red
DVPO 1-6.3M 6.35 0.8 9.5 0.25 x 1.65 Red
DVPO 2-4.8M 4.75 0.8 9.5 1.04 x 2.63 Blue
DVPO 2-6.3M 6.35 0.8 9.5 1.04 x 2.63 Blue
DVPO 5 6.3M 6.35 0.8 9.5 2.63 x 6.64 Yellow
Suitable crimping tools:
Red: DHC 15, DHC 15Y, DHCR 1, DHCR 15, DBMT 1, 3 & 4
Blue: DHC 15, DHC 15Y, DHCR 2, DHCR 15, DBMT 1, 3 & 4
Yellow: DHC 15, DHC 15Y, DHCR5, DHCR 15, DBMT 1, 3 & 4
Vinyl insulated
Male
Part Dimensions mm Conductor
Number d D L Size mm2
DPO 1-4.8M 4.75 0.5 6.35 0.3–0.75
DPO 1-6.3M 6.35 0.8 9.5 0.5–2.0
DPO 2-6.3M 6.3 6.3 9.5 1.0–2.5
Suitable crimping tools:
DHCF 15, DHCRF 15, DBMT 1, 3 and 4
Vinyl insulated Vinyl insulated
14
PUSH ON TERMINALS (INSULATED AND NON INSULATED)
Male/Female
Piggyback Adaptors
Push-on Terminal Type
PVC Insulating Covers
Flag Terminal Type PVC
Insulating CoversFemale Nylon Flag
Disconnectors
LD Terminals • Hand Tools • Accessories
Part Conductor Colour
Number Size mm2
DVPOA 1-6.3 0.25–1.65 Red
DVPOA 2-6.3 1.04–2.63 Blue
DVPOA 5-6.3 2.63–6.64 Yellow
Suitable crimping tools:
Red DHC 15, DHC 15Y, DHCR 1, DHCR 15,
DBMT 1, 3 & 4.
Blue DHC 15, DHC 15Y, DHCR 2, DHCR 15,
DBMT 1, 3 & 4.
Yellow DHC 15, DHC 15Y, DHCR 5, DHCR 15,
DBMT 1, 3 & 4.
Part Conductor Colour
Number Size mm2
DNFPO 1-6.3 FLAG 0.25-1.65 Red
DNFPO 2-6.3 FLAG 1.04-2.63 Blue
DNFPO 1-4.8 FIAG 0.25-1.65 Red
DNFPO 2-4.8 FLAG 1.04-2.63 Blue
Suitable crimping tool: DHCR-FL
Part Width mm
Number
DVC6.3 FLAG 6.3
Part To suit
Number Width mm
DPO1-6.3 FLAG 6.3
Vinyl insulated
Part To Suit Male/
Number Width mm2 Female
DVFPO 1-6.3FIT 6.3 Female
DVFPO 1-6.3MIT 6.3 Male
DVFPO 2-6.3FIT 6.3 Female
DVFPO 2-6.3MIT 6.3 Male
DVFPO 5-6.3FIT 6.3 Female
DVFPO 5-6.3MIT 6.3 Male
Suitable crimping tools:
DHCR 15, DHCR HS.
Part Dimensions mm
Number A C
DVC 2.8 2.8 4.0 x 2.4
DVC 4.g 2.4 5.2 x 2.0
DVC 6.3 1 2.8 8.0 x 2.0
DVC 6.3 2 5.6 x 2.0 8.0 x 2.0
DVC 9.5 4.8 10.3 x 4.0
For use with:
DVC 2.8 2.8 Push On (0.110")
DVC 6 3 1 6.3 Push On (0.250")
DVC 6 3 2 6.3 Push On (0.250")
DVC 9.5 9.5 Push On (0.375")
Fully insulated
Part Conductor
Number Size mm2
DPOA 1 6.3 0.25–1.65
DPOA 2 6.3 1.04–2.63
DPOA 5 6.3 2.63–6.64
Suitable crimping tools:
DHCF 15, DHCRF 15, DBMT 1, 3 & 4.
Part
Number
DPOA 6.3
Non insulated
Non Crimp Adaptor
For Insulated DisconnectTerminals without coppersleeve please add NTG to theend of part number i.e. DVPO1 6.3F NTG
These adaptors are to suit all6.3mm (0.250”) Series pushon terminals.
Female Flag
Disconnector
Interlocking Nylon
Disconnectors (Non Twin Grip)
16
CORD END TERMINALS (INSULATED)
LD Terminals • Hand Tools • Accessories
CODE T (FRENCH) CODE W (GERMAN)
Part Number Colour Part Number
DICE1125 Violet PET1125
DICE1134 Pink PET1134
DICE0505/M PET0505/M
DICE0505 White PET0505
DICE0505/L PET0505/L
DICE7575/M PET7575/M
DICE7575 PET7575
DICE7575/L PET7575/L
DICE7575/XL PET7575/XL
DICE1010/M PET1010/M
DICE1010 PET1010
DICE 1010/L PET1010/L
DICE1010/XL PET1010/XL
DICE 1515/M PET 1515/M
DICE 1515/L Black PET 1515/L
DICE 1515/XL PET 1515/XL
DICE2525 PET2525
DICE2525/L Grey PET2525/L
DICE2525/XL PET2525/XL
DICE4040 PET4040
DICE4040/L Orange PET4040/
DICE4040/XL PET4040/XL
DICE6040 PET6060
DICE6040/L PET6060/L
DICE0010 PET0010
DICE0010/L PET0010/L
DICE0016 PET0016
DICE0016/L PET0016/L
DICE0025 PET0025
DICE0025/L PET0025/L
Size mm
Colour mm2 d 1 S1 d3 S2 L1 L2
Lt Blue 0.25 0.8 0.15 2.0 0.25 10.4 6.0
Turquoise 0.34 0.8 0.15 2.0 0.25 10.4 6.0
12.0 6.0
Orange 0.5 1.0 0.15 2.65 0.25 14.0 8.0
16.0 10.0
12.4 6.0
14.6 8.2
16.4 10.0
18.4 12.0
12.4 6.0
14.6 8.2
16.4 10.0
18.4 12.0
14.6 8.2
Red 1.5 1.7 0.15 3.5 0.25 16.4 10.0
24.4 18
15.2 8.2
Blue 2.5 2.2 0.15 4.0 0.25 19.0 12.0
25.0 18.0
16.5 9.0
Grey 4.0 2 8 0 2 4 5 0 3 16.5 12.0
25.5 18.0
20.0 12.0
26.0 18 0
21.5 12.0
27.5 18.0
22.2 12.0
28.2 18.0
29.0 16.0
35.0 22.0
In accordance with DIN Standard 46228 Part 4 suitable for tri-rated cables. * Denotes Standard Stock Items.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
White 0.75 1 2 0 15 3 0 0.25Blue
Red Yellow 1.0 1.4 0.15 3.3 0.25
Green Black 6.0 3.5 0.2 6 3 0.3
Brown Ivory 10.0 4.5 0.2 7.6 0.4
Green 16.0 5.8 0.2 8.8 0.4Ivory
Black Brown 25.0 7.3 0.2 11.2 0.4
17
CORD END TERMINALS(INSULATED WITH PARALLEL SLEEVE)
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
CORD END TERMINALS(NON INSULATED)
CODE T (FRENCH) CODE W (GERMAN)
Part Number Colour Part Number
DICE0035 PET0035
Red
DICE0035/L PET0035/L
DICE0050 PET0050
Blue
DICE0050/L PET0050/L
DICE0070 Yellow
DICE0095 Red
In accordance with DIN Standard 46228 Part 1.
Suitable for Tri rated cables.
Cable Size
Part Number mm2 L2 D1 S1
DUCE0505 0.5 6.00 1.00 0.15
DUCE7575 0.75 10.00 1.4 0.15
DUCE1010 1.00 10.00 1.6 0.15
DUCE1515 1.50 10.00 1.8 0.15
DUCE2525 2.50 12.00 2.3 0.15
DUCE4040 4.00 12.00 2.8 0.20
DUCE6040 6.00 15.00 3.6 0.20
DUCEOO10 10.00 15.00 4.5 0.20
DUCE0016 16.00 15.00 5.8 0.20
DUCE0025 25.00 15.00 7.3 0.20
DUCE0035 35.00 20.00 8.3 0.30
DUCE0050 50.00 22.00 10.3 0.30
DUCE0070 70.00 26.00 12.6 0.30
DUCE0095 95.00 30.00 15.2 0.40
Size mm
Colour mm2 d 1 S1 d3 S2 L1 L2
16.0
Beige 35 8.3 0.3 12.7 0.4 28.4
25.0
20.0
Olive 50 10.3 0.3 15.0 0.5 34.0
25.0
70 13.5 0.3 16.0 0.5 35.0 20.0
95 14.5 0.7 16.0 0.5 42.0 25.0
Din Standard Colour Scheme, French & German can be supplied to order.
Code Sizes mm
Part Number Colour mm2 dl S1 d3 d2 S2 L1 L2
DICE2005 White 2 x 0.5 1.5 0.15 5.6 3.6 0.25 15.0 8.0
DICE2075 Grey 2 c 75 1.8 O 15 6 2 3 6 0 75 15 0 8 0
DICE2010 Red 2 x 1.0 2.0 0.15 6.0 4.0 0.30 15.0 8.0
DICE2015 Black 2 x 1.5 2.3 0.15 7.2 4.2 0.30 16.0 8.0
DICE2025 Blue 2 x 2.5 2.9 0.15 8.5 5.0 0.30 18.0 10.0
DICE2040 Lt Grey 2 x 4.0 3.8 0.20 9.2 5.7 0.35 23.0 12 0
DICE2060 Yellow 2 x 6.0 4.9 0.20 10.5 6.8 0.35 24.0 14.0
DICE2100 Red 2 x 10.0 6.5 0.20 13.0 8.0 0.40 26.0 14.0
DICE2160 Blue 2 x 16.0 3 7 0.20 19.3 10 5 0.40 31.0 14 0
Suitable Crimping Tools
DCER 510, DCER 1635, DCE 025, DCE 516.
*
*
*
*
*
*
18
AUTO BULLET AND SOCKET CONNECTORS
LD Terminals • Hand Tools • Accessories
Double Female Socket
Connector
Brass Bullet
Single Female Socket
Connector
BRASS TABS
Female
Male
Use indent ratchet tool DHCRBT
BLACK VINYL
Part Dimensions mmNumber d L
DVSC2 4.5 30.0
For use with Brass Bullet DAB
BLACK VINYL
Part Dimensions mmNumber d L
DVSC1 4.5 30.0
For use with Brass Bullet DAB
Part Dimensions mmNumber D L d
DAB 4.6 11.5 1.95
For use with Brass Bullet DAB
VINYL INSULATED
Part Dimensions mm Conductor
Number A B D Size mm2 Colour
DVAB1M 9.0 23.0 4.0 0.25–1.65 Red
DVAB2M 9.0 23.0 5.0 1.04–2.63 Blue
DVAB2M4 11 23.0 4.0 1.04–2.63 Blue
DVAB5M 9.0 23.0 5.0 2.63–6.64 Yellow
FULLY VINYL INSULATED
Part Dimensions mm Conductor
Number A L Size mm2 Colour
DVAB1F 9.0 26.0 0.25–1.65 Red
DVAB2F 9.0 26.0 1.04–2.63 Blue
DVAB2F4 14 26.0 1.04–2.63 Blue
DVAB5F 9.0 26.0 2.63–6.64 Yellow
AUTO BULLET
20
LD Terminals • Hand Tools • Accessories
TYPE DBMT 3AA bench mounted air operated crimping toolsuitable for crimping many types of terminal upto 6.0 sq mm.
Will accept all jaw sets as detailed below.Reduces operator fatigue on volume output. Thefoot pedal control automatically adjusts jawclosing time longer or shorter so that eachcrimp is consistent regardless of operator. Jawsare sold separately (see below).
SPECIFICATIONSAir Pressure 80–115 PSi
Air Consumption 34L/min at 30 crimps per min
Dimensions 190 (L) x 99 (H) x 92 (W) mm
Weight 2.5Kgs
JAW PART NUMBER
DBMT3A-NI
CABLE RANGE
0.5 TO 6.0 SQ MM
TERMINAL
NONINSULATED
DBMT3A-PE1 0.5 TO 6.0 SQ MM INSULATED
DBMT3A-UPO 6.3 0.5 TO 6.0 SQ MMOPEN
BARREL
DBMT3A-CE1 0.5 TO 4.0 SQ MMCORDEND
DBMT3A-CE3 6 TO 10 SQ MMCORDEND
DBMT3CT (CUTTER)COPPER WIRE 6 DIA
ALUMINIUM WIRE 7 DIA
CRIMP SAMPLE
PNEUMATIC CRIMPING EQUIPMENT
24
LD Terminals • Hand Tools • Accessories
HAND CRIMPING TOOLS(WITH CONTROLLED CALIBRATING DEVICES)
THE ABOVE TOOLS CAN BE CALIBRATED MANUALLY AND PROVED IN
ACCORDANCE WITH ALL INTERNATIONAL STANDARDS
The Davico range of hand crimping tools has been selected tocomply with all variations to customer specification and havethe added advantage of compressing other manufacturers terminals.
DHCR 10Triple Jaw Ratchet Tool with controlled calibration suitable for crimping miniature insulated terminals 0.05to 2.55 sq. mm.
DHCR 15Triple Jaw Ratchet Indent Tool with controlled calibrationsuitable for crimping 0.25 to 6 sq. mm insulated terminals.
DHCR 1516Four Jaw Ratchet Tool for with controlled calibrationsuitable for crimping 1.5 to 16 sq. mm Davico coppertube terminals.
DHCRF 15Triple Jaw Ratchet Tool with controlled calibration suitable for crimping non insulated male/female disconnect terminals with ‘F’ crimp configuration.
DHCRF 025Double Jaw Ratchet Tool with controlled calibration suitable for ‘F’ crimp type miniature terminals/pins0.102 to 0.25 sq. mm.
DHCRF 05Double Jaw Ratchet Tool with controlled calibration suitable for ‘F’ crimp type miniature terminals 0.12 to 0.5 sq. mm.
DCER 510Six Jaw Ratchet Tool with controlled calibration suitablefor crimping insulated and non insulated cord end terminals 0.5 to 10 sq. mm.
DCER 1635Triple Jaw Ratchet Tool with controlled calibration suitable for crimping non insulated and insulated cordend terminals 16, 25 and 35 sq. mm.
DHCR – HS
Triple Jaw Ratchet Tool with controlled calibration suitable for crimping insulated heat shrink prior toapplication of heat gun. The compression ratio has nodetrimental effect on the heatshrink insulation 0.25 to6 sq. mm.
DHCR – FLDouble Jaw Ratchet Tool with controlled calibration suitable for crimping fully insulated nylon right angleflag terminals 0.25 to 2.5 sq. mm.
DHCR – CARatchet Tool for co-axial cables with controlled calibra-tion jaw sets RG58/RG59 but other sets are available.
26
Standard Industrial Terminals
Durable low cost copper or brass connectors.Manufacturer as single piece connectorsElectro tinned to protect from corrosion
Insulated with flared entry, colour codedvinyl sleevesAll disconnect terminals supplied with anti-vibration copper sleeve.
Ring
Part Number Stud Size
ERR3 3mm
ERR3.7 3.7mm
ERR4 4mm
ERR5 5mm
ERR6 6mm
ERR8 8mm
ERR10 10mm
ERR12 12mm
Ring
Part Number Stud Size
EBR3 3mm
EBR3.7 3.7mm
EBR4 4mm
EBR5 5mm
EBR6 6mm
EBR8 8mm
EBR10 10mm
EBR12 12mm
Ring
Part Number Stud Size
EYR3 3mm
EYR4 4mm
EYR5 5mm
EYR6 6mm
EYR8 8mm
EYR10 10mm
EYR112 12mm
Spade
Part Number Stud Size
ERF3 3.2mm
ERF3N 3.5mm
ERF4N 4mm
ERF5 5mm
ERF6 6mm
Spade
Part Number Stud Size
EBF3 3.2mm
EBF3N 3.5mm
EBF4N 4mm
EBF5 5mm
EBF6 6mm
Spade
Part Number Stud Size
EYF3N 3.5mm
EYF4N 4mm
EYF5 5mm
EYF6 6mm
Blade
Part Diameter x Length
Number mm
ERBL10 2.3 x 10.4
ERBL18 2.3 x 18.4
Blade
Part Diameter x Length
Number mm
EBBL9 2.8 x 9
EBBL18 2.3 x 18.4
Blade
Part Number Diameter x Length
mm
EYBL10 2.8 x 10
Pin
Part Diameter x Length
Number mm
ERP12 1.9 x 12
Pin
Part Diameter x Length
Number mm
EBP12 1.9 x 12
Pin
Part Number Diameter x Length
mm
ERP14 2.9 x 14
Butt
Part Number
ERB
27C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Standard Industrial Terminals
Female Push-on
Part Number Tab Size
ERPO 28 F5 2.8 x 0.5
ERPO 28 F8 2.8 x 0.8
ERPO 48 F5 4.8 x 0.5
ERPO 48 F8 4.8 x 0.8
ERPO 63 F 6.3 x 0.8
Female Push-on
Part Number Tab Size
EBPO 48 F5 4.8 x 0.5
EBPO 48 F8 4.8 x 0.8
EBPO 63 F 6.3 x 0.8
EBPO 85 F 8.5 x 0.8
Female Push-on
Part Number Tab Size
EYPO 28 F5 6.3 x 0.8
EYPO 28 F8 9.5 x 1.1
Male Push-on
Part Number Tab Size
ERPO 63M 6.3 x 0.8
Male Push-on
Part Number Tab Size
EBPO 63M 6.3 x 0.8
Male Push-on
Part Number Tab Size
EYPO 63M 6.3 x 0.8
Female Push-on
Fully Insulated
Part Number Tab Size
ERFPO 48 F5 4.8 x 0.5
ERFPO 48 F8 4.8 x 0.8
ERFPO 63 F 6.3 x 0.8
Female Push-on
Fully Insulated
Part Number Tab Size
EBFPO 48 F5 4.8 x 0.5
EBFPO 48 F8 4.8 x 0.8
EBFPO 63 F 6.3 x 0.8
Female Push-on
Fully Insulated
Part Number Tab Size
EYFPO 63F 6.3 x 0.8
EYFPO 95F 9.5 x 1.1
Push-on
Connector
Part Number Tab Size
ERPOA 63 6.3 x 0.8
Push-on
Connector
Part Number Tab Size
EBPOA 63 6.3 x 0.8
Push-on
Connector
Part Number Tab Size
EYPOA 63 6.3 x 0.8
Female Bullet
Part Number Bullet Dia
mm
ERAB 4F 4
Female Bullet
Part Number Bullet Dia
mm
EBAB 4F 4
EBAB 5F 5
Female Bullet
Part Number Bullet Dia
mm
EYAB 5F 5
Male Bullet
Part Number Bullet Dia
mm
ERAB 4M 4
Male Bullet
Part Number Bullet Dia
mm
EBAB 4M 4
EBAB 5M 5
Male Bullet
Part Number Bullet Dia
mm
EYAB 5M 5
28
Cable Stud Nominal Dimensions mmSize Size Partsq mm mm dia ØA B D ØE F G H J K Number
10 4 4.5 12 8.7 4.2 1.42 4 5 24 3 DX 10-45 4.5 12 8.7 5.2 1.42 4 5 24 3 DX 10-56 4.5 12 12 6.2 1.3 5 6 26 3 DX 10-68 4.5 12 12 8.4 1.03 6 9 30 3 DX 10-810 4.5 12 19 10.5 1.8 10 10 35 3 DX 10-1012 4.5 12 19 13 1.8 12 12 39 3 DX 10-12
16 5 5.5 15 11 5.2 1.4 4 9 32 4 DX 16-56 5.5 15 11 6.5 1.4 5 9 33 4 DX 16-68 5.5 15 11 8.4 1.31 6 9 34 4 DX 16-810 5.5 15 19 10.3 1.8 10 10 39 4 DX 16-1012 5.5 15 19 13 1.8 12 12 43 4 DX 16-12
25 5 7 15 12.6 5.2 2 5 6 30 4 DX 25-56 7 15 12.6 6.5 2 5 6 30 4 DX 25-68 7 15 16 8.4 1.6 6 9 34 4 DX 25-810 7 15 17.5 10.5 1.5 10 10 39 4 DX 25-1012 7 15 17.5 13 1.5 12 12 43 4 DX 25-12
35 6 8.6 18 15.7 6.4 2.2 8 8 39 5 DX 35-68 8.6 18 15.7 8.4 2.2 8 8 39 5 DX 35-810 8.6 18 16.2 10.5 2 9 11 43 5 DX 35-1012 8.6 18 18 13 1.8 9.2 10.8 43 5 DX 35-12
50 6 9.6 23 17.4 6.4 2.4 8.5 8.5 46 6 DX 50-68 9.6 23 17.4 8.4 2.4 8.5 8.5 46 6 DX 50-810 9.6 23 17.4 10.5 2.4 10 10 49 6 DX 50-1012 9.6 23 17.2 13 2.4 12 13 54 6 DX 50-12
All Copper TubeTerminals have aradiused entry
Copper Tube Terminals 1.5–240 Sq mm – Bell Entry
SPECIFICATION REQUIREMENT
a. Finish Electro tinnedb. Copper Conductivity to 97% IACSc. Copper tube double annealedd. All terminals up to 240mm2 will have bell mouth
cable entrancee. Working temperature up to 180°C (Standard)f. Working temperature with nickel plating up to
350°C (Special)
Copper Tube • HD Terminals • Tooling
29
Copper Tube • HD Terminals • Tooling
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Cable Stud Nominal Dimensions mmSize Size Partsq mm mm dia ØA B D ØE F G H J K Number
70 6 11.2 23 21.5 6.5 3 11 1 52 7 DX 70-68 11.2 23 21.5 8.4 3 11 11 52 7 DX 70-810 11.2 23 21.5 10.5 3 11 11 52 7 DX 70-1012 11.2 23 21.5 13 3 11 11 52 7 DX 70-1214 11.2 23 25 15 3 12.5 12.5 55 7 DX 70-1416 11.2 23 25 17 3 12.5 12.5 55 7 DX 70-16
95 8 13.5 30 21.5 8.4 3.9 12 12 63 9 DX 95-810 13.5 30 25 10.5 3.9 12 12 63 9 DX 95-1012 13.5 30 25 13 3.9 12 12 63 9 DX 95-1214 13.5 30 28 4.7 3.9 14 14 67 9 DX 95-1416 13.5 30 28 17 3.9 16 16 71 9 DX 95-16
120 8 15 25 27.5 8.4 3.9 12 12 59 10 DX 120-810 15 25 27.5 10.5 3.9 12 12 59 10 DX 120-1012 15 25 27.5 13 3.9 12 12 59 10 DX 120-1214 15 25 27.5 15 3.9 15 15 65 10 DX 120-1416 15 25 27.5 17 3.9 15 15 65 10 DX 120-1620 15 25 27.5 21 3.9 20 20 75 10 DX 120-20
150 8 16.5 26 30.2 8.4 4.38 14 14 65 11 DX 150-810 16.5 26 30.2 10.5 4.38 14 14 65 11 DX 150-1012 16.5 26 30.2 13 4.38 14 14 65 11 DX 150-1214 16.5 26 30.2 15 4.38 14 14 65 11 DX 150-1416 16.5 26 30.2 17 4.38 16 16 73 11 DX 150-1620 16.5 26 30.2 21 4.38 20 20 77 11 DX 150-20
185 10 19 28 34 10.5 4 14 14 68 12 DX 185-1012 19 28 34 13 4 14 14 68 12 DX 185-1214 19 28 34 15 4 14 14 68 12 DX 185-1416 19 28 34 17 4 16 16 72 12 DX 185-1620 19 28 34 21 4 18 18 76 12 DX 185-20
240 10 21 33 37.6 10.5 5 15 15 77 14 DX 240-1012 21 33 37.6 13 5 15 15 77 14 DX 240-1214 21 33 37.6 15 5 15 15 77 14 DX 240-1416 21 33 37.6 17 5 19 19 85 14 DX 240-1620 21 33 37.6 21 5 19 19 85 14 DX 240-20
Note 1 Blank terminal palms areavailable from 10 sq mm to 240 sqmm.
Note 2 When usinq flexible finestrand or welding cable it may benecessary to select the next largerterminal size, i.e. 70 sq mm fine
strand, select 95 sq mm terminal.
30
Copper Tube • HD Terminals • Tooling
Cable Stud Nominal Dimensions mmSize Size Partsq mm mm dia ØA B D ØE F G H J K Number
1.5 3 1.8 5 8 3.2 1 4 5 16 2 D 1.5-34 1.8 5 8 4.2 1 4 5 16 2 D 1.5-45 1.8 5 8 5.2 1 4 5 16 2 D 1.5-5
2.5 3 2.4 7 8 3.2 1 4 5 18 2 D 2.5-34 2.4 7 8 4.2 1 4 5 18 2 D 2.5-45 2.4 7 10 5.2 0.8 5 6 20 2 D 2.5-56 2.4 7 10 6.5 0.8 5 6 20 2 D 2.5-6
4–6 4 3.8 9 10 4.2 1.2 5 6 23 3 D 6-45 3.8 9 10 5.2 1.2 5 6 23 3 D 6-56 3.8 9 12 6.5 1 6 9 27 3 D 6-68 3.8 9 12 8.4 1 6 9 27 3 D 6-810 3.8 9 17 10.5 1.7 11 11 34 3 D 6-10
10 5 4.5 9 12 5.2 1.2 6 7 25 3 D 10-56 4.5 9 12 6.5 1.2 6 7 25 3 D 10-68 4.5 9 12 8.4 1.2 6 9 27 3 D 10-810 4.5 9 19 10.5 1.8 10 10 32 3 D 10-1012 4.5 9 19 13 1.8 12 12 37 4 D 10-12
16 5 5.4 12 12 5.2 1.4 7 7 30 4 D 16-56 5.4 12 12 6.5 1.4 7 7 30 4 D 16-68 5.4 12 12 8.4 1.4 7 9 32 4 D 16-810 5.4 12 19 10.5 1.8 10 10 36 4 D 16-1012 5.4 12 19 13 1.8 12 12 40 4 D 16-12
25 6 6.8 12 13 6.5 2 7 7 30 4 D 25-68 6.8 12 16 8.4 1.6 10 11 37 4 D 25-810 6.8 12 16 10.5 1.6 10 11 37 4 D 25-1012 6.8 12 16 13 1.6 12 11 39 4 D 25-12
35 6 8.2 15 15.3 6.5 2.4 9 9 38 5 D 35-68 8.2 15 15.3 8.4 2.4 9 9 38 5 D 35-810 8.2 15 18 10.5 2 10 11 38 5 D 35-1012 8.2 15 18 13 2 10 11 38 5 D 35-12
50 6 9.5 16 18 6.5 2.9 10 11 43 6 D 50-68 9.5 16 18 8.4 2.9 10 11 43 6 D 50-810 9.5 16 18 10.5 2.9 10 11 43 6 D 50-1012 9.5 16 18 13 2.9 10 11 43 6 D 50-12
70 6 11.2 18 21 6.5 3.5 12 13 50 7 D 70-68 11.2 18 21 8.4 3.5 12 13 50 7 D 70-810 11.2 18 21 10.5 3.5 12 13 50 7 D 70-1012 11.2 18 21 13 3.5 12 13 50 7 D 70-1214 11.2 18 28 15 2.2 16 16 57 7 D 70-1416 11.2 18 28 17 2.2 16 16 57 7 D 70-16
Copper Tube Terminals 1.5–1000 Sq mm – Straight Entry
All Copper TubeTerminals have aradiused entry
31
Copper Tube • HD Terminals • Tooling
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Cable Stud Nominal Dimensions mmSize Size Partsq mm mm dia ØA B D ØE F G H J K Number
95 8 13.5 20 25 8.4 3.9 13 13 55 9 D 95-810 13.5 20 25 10.5 3.9 13 13 55 9 D 95-1012 13.5 20 25 13 3.9 13 13 55 9 D 95-1214 13.5 20 28 15 3.2 16 16 61 9 D 95-1416 13.5 20 28 17 3.2 16 16 61 9 D 95-16
120 8 15 22 28 8.4 4.4 14 14 60 10 D 120-810 15 22 28 10.5 4.4 14 14 60 10 D 120-1012 15 22 28 13 4.4 14 14 60 10 D 120-1214 15 22 28 15 4.4 16 16 64 10 D 120-1416 15 22 28 17 4.4 16 16 64 10 D 120-16
150 8 16.5 26 30 8.4 4.7 16 16 69 11 D 150-810 16.5 26 30 10.5 4.7 16 16 69 11 D 150-1012 16.5 26 30 13 4.7 16 16 69 11 D 150-1214 16.5 26 30 15 4.7 16 16 69 11 D 150-1416 16.5 26 30.6 17 4.7 16 16 69 11 D 150-1620 16.5 26 30.6 21 4.2 19 23 79 11 D 150-20
185 10 18.5 32 34 10.5 5 17 17 78 12 D 185-1012 18.5 32 34 13 5 17 17 78 12 D 185-1214 18.5 32 34 15 5 17 17 78 12 D 185-1416 18.5 32 34 17 5 17 17 78 12 D 185-1620 18.5 32 34 21 5 17 17 78 12 D 185-20
240 10 21 38 38 10.5 5.5 20 20 92 14 D 240-1012 21 38 38 13 5.5 20 20 92 14 D 240-1214 21 38 38 15 5.5 20 20 92 14 D 240-1416 21 38 38 17 5.5 20 20 92 14 D 240-1620 21 38 38 21 5.5 20 20 92 14 D 240-20
300 12 23.5 42 43 13 6.5 22 22 101 15 D 300-1214 23.5 42 43 15 6.5 22 22 101 15 D 300-1416 23.5 42 43 17 6.5 22 22 101 15 D 300-1620 23.5 42 43.4 21 6.5 22 22 101 15 D 300-20
400 16 26.8 44 50.1 17 8 26 26 114 18 D400-1620 26.8 44 50.1 21 8 26 26 114 18 D 400-20
500 16 30 48 56 17 9 28 28 124 20 D 500-1620 30 48 56 21 9 28 28 124 20 D 500-20
630 16 35 56 65 17 10 33 33 144 22 D 630-1620 35 56 65 21 10 33 33 144 22 D 630-20
800 - 39 78 73 - 11.6 - - 170 17 D 800-B
1000 - 43 90 80.8 - 13.2 - - 200 20 D 1000-B
Note 1 Blank terminal palms are availablefrom 10 sq mm to 1000 sq mm.
Note 2 When usinq flexible fine strand orwelding cable it may be necessary to selectthe next larger terminal size, i.e. 70 sq mmfine strand, select 95 sq mm terminal.
32
Butt Connectors
Cable Dimensions mm Part Cable Dimensions mm PartSize Number Size NumberSq mm A B J Sq mm A B J
1.5 1.8 6 12 DBC1 95 13.5 22.5 45 DB952.5 2.4 7.5 15 DBC2 120 15 22.5 45 DB1204 to 6 3.8 7.5 15 DBC5 150 16.5 27.5 55 DB15010 4.5 10 20 DB10 185 18.5 32.5 65 DB18516 5.4 10 20 DB16 240 21 40 80 DB24025 6.8 16 32 DB25 300 23.5 42.5 85 DB30035 8.2 18 36 DB35 400 26.8 45 90 DB40050 9.5 20 40 DB50 500 30 50 100 DB50070 11.2 20 40 DB70 630 35 55 110 DB630
Larger sizes are available to order
Parallel Connectors
Cable Dimensions mm Part Cable Dimensions mm PartSize Number Size NumberSq mm A B J Sq mm A B J
1.5 1.8 7 DPC1 35 8.2 12 DP352.5 2.4 7 DPC2 50 9.5 16 DP504 to 6 3.8 7 DPC5 70 11.2 18 DP7010 4.5 9 DP10 95 13.5 20 DP9516 5.4 10 DP16 120 15 23 DP12025 6.8 11 DP25
Larger sizes are available to order
Solid Pin Connectors
Cable CableSize Part Size PartSq mm A B C D E Number Sq mm A B C D E Number
10 10 13 23 6.2 3.8 DSP10 95 25 26 51 17.5 11.5 DSP9516 13 17 30 7.1 3.8 DSP16 120 25 28 53 19.4 11.5 DSP12025 20 17 37 9.0 7.5 DSP25 150 32 32 64 21.5 15.6 DSP15035 20 17 37 10.6 7.5 DSP35 185 32 38 70 24.0 15.6 DSP18550 20 21 41 12.4 7.5 DSP50 240 32 44 76 27.3 15.6 DSP24070 25 23 48 14.7 11.5 DSP70 300 32 48 80 30.6 15.6 DSP300
Transformer Terminals (Four Bolt Fixing)
Cable Dimensions mmSize Stud PartSq mm Size D L M J N P Number
300 4 x 8 51 25.4 34.9 109 52 13.3 T300400 4 x 8 52 25.4 34.9 114 52 13.3 T400500 4 x 8 56 25.4 34.9 124 56 15.3 T500630 4 x 8 65 25.4 34.9 144 66 20.3 T630
Copper Tube • HD Terminals • Tooling
33C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Insulation Black Nylon.
Other colours can be manufacturedto quantity orders.MANUFACTURED TO ORDER.Nylon Insulated Copper Tube Terminals
Cable Dimensions mm PartSize NumberSq mm ØA A1 B1 D ØE G J J1
10 4.5 8 11 12 6.5 6 38 22 DN 10-64.5 8 11 12 8.4 6 40 22 DN 10-84.5 8 11 18 10.5 9 44 22 DN 10-10
16 5.4 9 13 12 6.5 7 45 27 DN 16-615.4 9 13 12 8.4 7 47 27 DN 16-815.4 9 13 18 10.5 9 50 27 DN 16-10
25 6.8 11 13 13 6.5 7 46 28 DN 25-66.8 11 13 16 8.4 10 53 28 DN 25-86.8 11 13 16 10.5 10 53 28 DN 25-10
35 8.2 14 14 15.3 8.4 9 53 30 DN 35-88.2 14 14 18 10.5 10 56 30 DN 35-108.2 14 14 18 13 10 60 30 DN 35-12
50 9.5 16 16 16 8.4 10 63 36 DN 50-89.5 16 16 16 10.5 10 63 36 DN 50-109.5 16 16 16 13 10 67 36 DN 50-12
70 11.2 18 18 18 8.4 12 72 40 DN 70-811.2 18 18 18 10.5 12 72 40 DN 70-1011.2 18 18 18 13 12 72 40 DN 70-12
95 13.5 20 20 20 8.4 13 79 44 DN 95-813.5 20 20 20 10.5 13 79 44 DN 95-1013.5 20 20 20 13 13 79 44 DN 95-12
HD Nylon Insulated Pins
Cable Dimensions mm PartSize NumberSq mm A A1 B1 D E G J J1
10 4.3 8 13 4.3 2.4 12 35 21 DNP10-1216 9 5.8 15 5.5 2.6 13 41 25 DNP16-1425 11 7.5 14 7 4 16 45 25 DNP25-1635 14 9 16 8 4 20 53 28 DNP35-2050 16 10.5 19 9 4 20 61 35 DNP50-20
HD Non Insulated Pins
Cable Dimensions mm PartSize NumberSq mm A A1 B1 D E G J
10 4.3 8 6.7 4.3 2.4 12 22 DP10-1216 5.8 10 8.2 5.5 2.6 13 26 DP16-1425 7.5 11 11.1 7 4 16 31 DP25-1635 9 12 12.6 8 4 20 37 DP35-2050 10.5 16 14.1 9 4 20 42 DP50-2070 11 18 16 10 4.5 20 45 DP70-20
Copper Tube • HD Terminals • Tooling
36
Manual Hand Compression Tooling
Copper Tube • HD Terminals • Tooling
DHCR1516
DHC95
DHC50HDHC120HDHC150H
DHCR1510 or DHCR0516
DHCRN2570
DHCR1516Four jaw ratchet tool with controlled calibrationsuitable for crimping 1.5 to 16 sq mm Davico copper tube terminals.
DHCR1510Ratchet controlled tool, designed to indent crimpsheet and tube terminals up to 10 sq mm. Range 1.5 to 10 sq mm.
DHCR0516Ratchet controlled tool with four jaw apertures suitable for indent crimping from 0.5 to 16 sq mmon copper tube terminals. When using Davico U.K.terminals this tool will crimp 25 sq mm.
DHC95Heavy duty indent crimping tool for tube and sheetterminals 10 to 95 sq mm with non ratchet screwadjustment.
DHCRN2570Hand ratchet crimping tool for crimping un insulatedor insulated Nylon / Vinyl tube oF sheet terminals.
Range Tube: Insulated 25 to 70 sq mm Sheet: Insulated AWG6 to AWG1/0 Tube: Un-insulated 25 to 95 sq mm Sheet: Un-insulated AWG4 to AWG2/0 Length: 409mm.Weight: 2.12Kg.
DHC50H,DH120H and DHC150H
DHC50H for tubular cable lugs of 6 up to 50 sq mm.Length: 390mm, Weight: 1.1OKg
DHC 120H for tubular cable lugs of 6 up to 120 sq mm.Length: 650mm, Weight: 2.90Kg
DHC 150H for tubular cable lugs of 25 up to 150 sq mm.
37
Copper Tube • HD Terminals • Tooling
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
DHY150Hydraulic compression tool with crimping force of50Kn. The compact design incorporates hexagonal,indent and 'M' and 'W' indent crimping from 10 to150 sq mm with two applications. Adjustable dieram.
The tool is supplied complete with a steel carryingcase.
DHY240As the DHY150 but with die sets to incorporate thecompression crimping up to 240 sq mm.
DHHCH630Hydraulic press head, complete with 3/8" NPTfemale quick coupler to crimp connectors up to 630sq mm.
To operate, this head must be fitted to a hydraulicpump, developing a pressure of 10,000 Ib/in2
(7OObar), such as the DHPN10.
Hexagon and indent form dies are available.
DHYCC400Twin stage hydraulic hand compressor to crimp connectors up to 400 sq mm (hexagonal).
This tool features a double speed action to saveoperator time and effort.
The press head is rotatable by 180° to permit easyoperation even in difficult conditions.
The DHYCC400 is supplied in a stout steel case provided with a compartment to house 12 sets ofdies.
Hexagon and indent form dies are available.
DHHCC400Hydraulic press head, complete with 3/8" NPTfemale quick coupler to crimp connectors up to 400sq mm (hexagonal).
The DHHCC400 uses the same dies as theDHYCC400. To operate, this head must be fitted to ahydraulic pump, developing a pressure of 10,000Ib/in2 1700bar), such as the DHPN10.
Hydraulic Compression Tooling
DHY150
DHYCC400
DHHCC400DHHCH630
DHY240
38
DHFPC 2Two stage hydraulic foot pump developing a pressure of10,000 Ib/in2 (7OO bar).
This pump is provided with 3 metres of high pressure
flexible hose featuring a 3/8" NPT male quick coupler.
Pressure release is effected by means of an easy actionsmall pedal, situated on the back part of the pump.
The DHFPC 2 is supplied in a stout steel case.
DHPN 10Hydro pneumatic foot operated power source for usewith Davico hydrautic crimpinq heads. Develops a pressure of 10,000 Ib/in2 (7OObar).
Hoses are available as additions.
DHEPC 1Electrically controlled pump unit with basic unitpower supply of 220/240V complete with motorprotection cut off for regulating working pressureIncludes integral foot pedal and 2.5 metre hose.Pressure is adjustable from 450 to 700 bars.Power 0.9 Kw.
The unit can also be connected to a remote footpedal if required.
Also available at 11OV and 380V supplies.
DHEPC 2Electrically controlled pump unit with 220/240V supplycomplete with motor protection, they are designed forintermittent duty and will start under full load conditions.
All models have 3 metre remote control foot feature anda 2 gallon thermoplastic reservoir.
HD Pump Units
Copper Tube • HD Terminals • Tooling
DHFPC 2
DHEPC 1 DHEPC 2
DHPN 10
42
Cable Ties and Accessories
Miniature Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
80 2.5 14 8.1 NT14M NTB14M
100 2.5 20 8.1 NT20M NTB20M
120 2.5 24 8.1 NT24M NTB24M
160 2 5 36 8.1 NT36M NTB36M
200 2.5 50 8.1 NT50M NTB50M
Intermediate Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
140 3.6 30 18.2 NT30I NTB30I
200 3.6 50 18.2 NT50I NTB50I
295 3.6 75 18.2 NT75I NTB75I
370 3.6 100 18.2 NT100I NTB100I
Standard Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
120 4.8 24 22.2 NT24S NTB24S
160 4.8 36 22.2 NT36S NTB36S
180 4 8 40 22.2 NT40S NTB40S
200 4.8 50 22.2 NT50S NTB50S
250 4.8 70 22.2 NT70S NTB70S
295 4.8 75 22.2 NT75S NTB75S
370 4.8 100 22.2 NT100S NTB100S
430 4.8 115 22.2 NT115S NTB115S
*In cases where page width does not allow ties to be shown to scale thedimension indicated should be added to give correct proportion.
Add 100mm*
NT/NTB 14M NT/NTB 20M NT/NTB 24M
NT/NTB 30I
NT/NTB 24S NT/NTB 36S NT/NTB 40S NT/NTB 50S NT/NTB 70S NT/NTB 75S
NT/NTB 50I NT/NTB 75I
NT/NTB 36M NT/NTB 50M
Add 100mm*
43
Cable Ties and Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Eurolok Cable Ties are produced on multi impression tools which mould complete one piece ties
with no metal parts.
They are manufactured from tough durable Nylon 6/6 which has been tested to underwriters laboratory
UL94V2. The material is zero halogenated and also has a low smoke and fume capability when compared
with materials such as PVC, PP, PE, ABS, POM, ECT. The classified oxygen index at max 28% dry is
considered excellent in halogen free and L.S.F. situations, with the test method conducted in accordance
with data sheet DAV1826 and the test status as indicated below in table A. The health and safety
directives are substantiated on data sheet DAV1825 both of which are available upon application. In the
case of Underwriters Laboratory specification requirements, the full implications of UL1565 have been
applied as indicated against file No.E155866 and E157276. (Copies are available on application).
These specifications include for the performance testing requirements with regard to Flammability,
Tensile Strength, Vibration, Corrosion, etc., and in most cases exceed the recommendations. The ties can be
tensioned by hand or by the use of applied tensioning tools. When using tensioning tools it is advisable to
pre set the tooling to the proposed setting as detailed in Table 'B' Page 55.
The colour shade of the standard ties is naturai nylon or black, but other colours are available to special
order. Black cable ties are recommended for general outdoor use and have a highly durable resistance to
Ultra Violet Light.
Due to the variation in requirement for this type of application the cable ties can be manufactured from
a higher performance Nylon 6/6 with intensive weather resistant qualities. All general specification details
are incorporated as indicated in Table 'A' and for any additional information please contact our offices.
Table ATest Method
Material Nylon 66
Working Temperature Range -40°C to 85°C
UL Flammability Rating UI94 V2
Oxygen Index 25%–28%
Smoke Density Flaming 35Non Flaming 13
Water Absorbtion (24 hours) 1.3%
Loop Tensile Strength (Kgs)
Miniature 8.1 Kgs
Intermediate 18.2 Kgs
Standard 22.2 Kgs
Light Heavy 54.5 Kgs
Heavy 79.4 Kgs
Extra Heavy 113.5 Kgs
NT/NTB 100S NT/NTB 115S
NT/NTB 100I
44
Cable Ties and Accessories
Light Heavy Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
150 7.6 36 54.5 NT36LH NTB36LH
200 7.6 50 54.5 NT50LH NTB50LH
290 7.6 80 54.5 NT80LH NTB80LH
370 7.6 105 54.5 NT105LH NTB105LH
Heavy Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
450 8.0 115 62 NT115H NTB115H
550 8.0 140 62 NT140H NTB140H
762 9.0 190 79.4 NT19OH NTB19OH
812 9.0 230 79.4 NT230H NTB230H
*In cases where page widthdoes not allow ties to beshown to scale the dimensionindicated should be added togive correct proportion.
Add 50mm*
Add 200mm*
Add 500mm*
Add 300mm*
Add 500mm*
NT/NTB 100XH
NT/NTB 36LH NT/NTB 50LH
45C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Cable Ties and Accessories
Extra Heavy Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
230 12.7 50 113.5 NT50XH NTB50XH
280 12.7 70 113.5 NT70XH NTB70XH
380 12.7 100 113.5 NT100XH NTB100XH
450 12.8 125 113.5 NT115XH NTB115XH
550 12.8 150 113.5 NT140XH NTB140XH
762 12.8 200 113.5 NT190XH NTB190XH
880 12.7 250 113.5 NT250XH NTB250XH
1000 12.7 300 113.5 NT300XH NTB300XH
Extra Wide Ties
The Eurolok range of heavy duty cable ties are designed for applications that require combined high strength fixing and a positive
locking capability. They are particularly suitable in difficult situations frequently found in Petro Chemical or Marine Industries.
They are available in two colours natural or black. See Table A (page 43) for full specification of nylon material.
NT/NTB 115XH
NT/NTB 190XH NT/NTB 250XH NT/NTB 300XH
NT/NTB 140XH
NT/NTB 50XH NT/NTB 70XH
NT/NTB 190H NT/NTB 230H
NT/NTB 115H NT/NTB 140H
NT/NTB 80LH NT/NTB 105LH
46
Cable Ties and Accessories
Releasable Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
200 4.8 50 22.2 NT5ORE NTB5ORE
300 4.8 75 22.2 NT75RE NTB75RE
370 4.8 100 22.2 NT100RE NTB1OORE
Standard Mounting Head Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
205 4.2 50 22.2 NT50SFH NTB50SFH
370 4.8 100 22.2 NT1OOSFH NTB1OOSFH
Add 100mm*
Add 50mm*
NT/NTB 50RE
NT/NTB 50SFH
NT/NTB 120LHFH
Hole Size 6mm Dia.
Hole Size 6mm Dia.
*In cases where page width does not allow ties to be shown to scalethe dimension indicated should be added to give correct proportion.
47
Cable Ties and Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Light Heavy Mounting Head Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
400 7.9 120 58 NT12OLHFH NTB12OLHFH
Push Mount Tie
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural Black
155 3.5 40 18 NT30IPM NTB30IPM
Releasable cable ties, designed to facilitate routing changes and repairs. Press tab for easy removal. Mountable headcable ties used to secure bundled harnesses to panels. They may also be pre mounted to existing installations beforefinal assembly.
See ‘Table A’ for full specification of nylon material. See page 56 for explanation of Part Numbering System.
NT/NTB 75RE NT/NTB 100RE
NT/NTB 100SFH
NT/NTB 30IPMPre drilled hole 3.5 dia
48
Cable Ties and Accessories
Miniature Marker Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural
100 2.5 18 8.1 NT18MMT
Standard Marker Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural
200 4.6 50 22 NT40SMT
270 4.8 68 22 NT70SMT
Add 50mm*
NT 18MMT
NTB 40LT
*In cases where page width doesnot allow ties to be shown toscale the dimension indicatedshould be added to give correctproportion.
49
Cable Ties and Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Nylon 6.6. Data
Working Temperature -40°C to +85°C
Water Absorbtion 1.3%
Flammability Rating UL 94 V2
NT 40SMT NT 70SMT
NTB 70LT NTB 100LT NTB 140LT NTB 220LT
Nylon Lashing Tie Range
LENGTH WIDTH MAX. DIA. MIN. STRENGTH PART NUMBER
mm mm mm kg Natural
180 9 40 40 NTB40LT
265 9 70 40 NTB70LT
360 9 100 40 NTB100LT
500 9 140 40 NTB140LT
750 9 220 40 NTB220LT
50
Cable Ties and Accessories
1-Way Adhesive Bases
DIMENSIONS mm MAX. CABLE PART NUMBER
TIE WIDTH Natural Black
A B C F H mm
19 19 4.3 4 5 3.6 NB1 NBB1
25 25 4.3 5 7 4.8 NB2 NBB2
2-Way Adhesive Bases
DIMENSIONS mm MAX. CABLE PART NUMBER
TIE WIDTH Natural Black
A B C F H mm
19 19 4.3 4 5 3.6 NB12 NBB12
25 25 4.3 5 7 4.8 NB22 NBB22
1-Way 2-Way
51C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Cable Ties and Accessories
Cradles
• They maintain the ties firmly in position increasing their resistance.
• They are supplied with holes for fixing screws.
MAX. CABLE DIMENSIONS PART NUMBER
TIE WIDTH mm Natural Black
mm A B C F H
9 15 23 4.9 9 9 CTM2 CTMB2
Eyelets
• The eyelet enables the cable tie to be secured from either direction.
MAX. CABLE DIMENSIONS PART NUMBER
TIE WIDTH mm Natural Black
mm A B C F H
4.8 9.5 19.1 4.3 5 5 CTM 1 CTMB1
Eurolok accessories are designed to incorporate the majority of features applicable to the positioning
of cable ties.
Self adhesive bases, cradles, eyelets, and clamps, are supplied and manufactured from A.B.S. or
Nylon 6/6 material.
In case of self adhesive components the adhesive pads themselves have a base synthetic rubber
foundation which when applied gives a high permanent bond to most surfaces. On all applications a
dual option of bolt fixings is designed into the base as a preference if required.
Cradles Eyelets
52
Cable Ties and Accessories
Cable Mounts• Designed for heavy duty harnessing applications.
• Self adhesive.
• Provides fast, strong mounting system for securing cables.
DIMENSIONS mm PART NUMBER
A B C D Natural Black
16 9.5 4.5 4.5 NCC5 NCCB5
25 12.5 7.5 11 NCC11 NCCB11
25 16 14.5 18 NCC18 NCCB18
‘P’ CLIPS• For economical fixing of cables
• Material: Nylon
• Colour: Natural or Black
DIMENSIONS mm PART NUMBER
A B C D E F Natural Black
5.7x4.6 10.5 9.5 4.8 19.8 1.3 PC19 PC19B
6.7x4.6 12.0 10.0 6.0 22.0 1.0 PC22 PC22B
6.7x4.6 12.5 12.0 9.0 24.0 1.0 PC24 PC24B
6.7x4.6 15.2 12.0 12.0 31.0 1.0 PC31 PC31B
6.7x4.6 18.0 12.0 19.1 35.0 1.0 PC35 PC35B
6.7x4.6 22.0 12.0 25.4 43.0 1.0 PC43 PC43B
54
Cable Ties and Accessories
NYLON CABLE MARKINGS
If cable identification is required the natural coloured nylon markers
can be fitted to any 4.8 wide tie in a horizontal or vertical position.
DIMENSIONS mm PART NUMBER
A B C
40 20 1.3 NCM1
MASONRY MOUNT
The MM9 masonry mount is used to secure cabie ties to a
wall. Manufactured from Nylon, the maximum width of
cable tie that can be used with the masonry mount is 9mm.
Fix by drilling a 7mm diameter hole for use in soft materials
wood, chipboard, plasterboard etc) and an 8mm diameter
hole in hard materials (brick etc).
Part No Max Tie Size Length mm
MM9 9.5mm 42.6 mm
A C
B
55C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Cable Ties and Accessories
TENSIONING TOOLS
DTG1
Standard Adjustable nylon tensioning tool for cable tie widths
from 2.2 to 4.8mm.
DTGM1
Standard Adjustable metal tensioning tool for cable tie
widths from 2.2 to 4.8mm.
DTGM1/HD
Standard metal tensioning tool for cable tie widths from
4.8 to 13mm.
Table B
TIE WIDTH RECOMMENDED GUN SETTINGS
mm DTG 1 DTGM 1 DTGM 1/HD
2.5 2.5kg NO.0 -
3.6 6.0kg NO.1 -
4.8 14.0kg NO.3 -
7.6 - - To suit
90 - - To suit
56
Cable Ties and Accessories
EXPLANATION OF EUROLOK PART NUMBERING SYSTEM
Example: NT 50M
NT 50 M
Nylon Maximum Miniature
Tie Bundle
Diameter
Example: NTB 50M
NT B 50 M
Nylon Black Maximum Miniature
Tie Bundle
Diameter
FULL CODE LIST
WIDTH
M Miniature 2.5
I Intermediate 3.6 or 3.2
S Standard 4.8, 4.6 or 4.2
LH Light Heavy Duty 7.6
H Heavy Duty 9.0
MPM Miniature Push Mount Tie 2.5
XH Extra Heavy Duty 12.7
RE Releasable 4.8 and 12.7
FH Fixing Head 4.8 and 7.6
LT Lashing Tie 9
MMT Miniature Marker Tie 2.5
SMT Standard Marker Tie 4.8
Every Part Number should include one of the above codes to denote its width.
65
Electrical Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
TIE DIAGRAM SHOWN IS THAT OF A COATED STAINLESS STEEL ROLLER BALL CABLE TIE
Minimum loop tensile strength 4.6 mm wide = 44 KgsMinimum loop tensile strength 7.9 mm wide = 110 Kgs
S = Standard Dimension A Nominal Dimension D NominalLH = Light Heavy Dimension B + -0.4mm Dimension E NominalAll dimensions are in mm Dimension C + -0.04mm
Part NumberNatural Coated A B C D E Max. Dia.
SRBT20S SRBTC20S 100 4.6 0.25 6.3 4.0 20
SRBT24S SRBTC24S 125 4.6 0.25 6.3 4.0 24
SRBT30S SRBTC30S 150 4.6 0.25 6.3 4.0 35
SRBT50S SRBTC50S 200 4.6 0.25 6.3 4.0 50
SRBT1OOS SRBTC1OOS 360 4.6 0.25 6.3 4.0 100
SRBT115S SRBTC115S 520 4.6 0.25 6.3 4.0 150
SRBT175S SRBTC175S 680 4.6 0.25 6.3 4.0 200
SRBT225S SRBTC225S 840 4.6 0.25 6.3 4.0 250
SRBT300S SRBTC300S 1000 4.6 0.25 6.3 4.0 300
SRBT350S SRBTC350S 1200 4.6 0.25 6.3 4.0 370
SRBT400S SRBTC400S 1400 4.6 0.25 6.3 4.0 430
SRBT50LH SRBTC50LH 200 7.9 0.25 10.3 5.4 50
SRBT1OOLH SRBTC1OOLH 360 7.9 0.25 1 0.3 5.4 100
SRBT115LH SRBTC115LH 520 7.9 0.25 10.3 5.4 150
SRBT175LH SRBTC175LH 680 7.9 0.25 1 0.3 5.4 200
SRBT225LH SRBTC225LH 840 7.9 0.25 10.3 5.4 250
SRBT300LH SRBTC300LH 1000 7.9 0.25 1 0.3 5.4 300
SRBT350LH SRBTC350LH 1200 7.9 0.25 10.3 5.4 370
SRBT400LH SRBTC400LH 1400 7.9 0.25 10.3 5.4 430
STAINLESS STEEL ROLLER BALL CABLE TIE
66
Electrical Accessories
Minimum loop tensile strength 7.0 mm wide = 32 KgsMinimum loop tensile strength 12.0 mm wide = 50 Kgs
S = Standard Dimension A Nominal Dimension D NominalLH = Light Heavy Dimension B + -0.4mm Dimension E NominalXH = Extra Heavy Dimension C + -0.04mm All dimensions are in mm
Part Number
Natural Coated A B C D E Max. Dia.
SLT36LH SLTC36LH 150 7.0 0.30 8.0 3.2 45
SLT50LH SLTC50LH 200 7.0 0.30 8.0 3.2 60
SLT60LH SLTC60LH 225 7.0 0.30 8.0 3.2 70
SLT70LH SLTC70LH 250 7.0 0.30 8.0 32 75
SLT80LH SLTC80LH 300 7.0 0.30 8.0 3 2 95
SLT105LH SLTC105LH 360 7.0 0.30 8.0 3.2 110
SLT115LH SLTC115LH 450 7.0 0.30 8.0 3.2 140
SLT140LH SLTC 140LH 600 7.0 0.30 8.0 3.2 190
SLT150LH SLTC150LH 610 7.0 0.30 8.0 3.2 190
SLT200LH SLTC200LH 750 7.0 0.30 8.0 3 2 235
SLT300LH SLTC300LH 1000 7.0 0.30 8.0 32 315
SLT36XH SLTC36XH 150 12.0 0.35 13.0 3.8 45
SLT50XH SLTC50XH 200 120 035 13.0 3.8 60
SLT60XH SLTC60XH 225 12.0 0.35 13.0 38 70
SLT70XH SLTC70XH 250 12.0 0.35 13.0 38 75
SLT105XH SLTC105XH 360 12.0 0.35 13.0 3.8 110
SLT115XH SLTC115XH 450 12.0 0.35 13.0 3.8 140
SLT140XH SLTC140XH 600 12.0 0.35 13.0 3.8 190
SLT150XH SLTC150XH 610 12.0 0.35 13.0 38 190
SLT200XH SLTC200XH 750 12.0 0.35 13.0 38 235
SLT30OXH SLTC300XH 1000 12.0 0.35 13.0 3.8 315
STAINLESS STEEL LADDER CABLE TIES
67
Electrical Accessories
C A L L + 4 4 ( 0 ) 1 2 1 5 2 2 3 0 4 0 / 5 2 0 7 1 0 1
Part Number Coated A B C D E F G Max. Dia.
SRTC36S 145 5.0 0.50 12.5 3.5 7.5 13.0 36
SRTC60S 225 5.0 0.50 12.5 3.5 7.5 13.0 60
SRTC75S 325 5.0 0.50 12.5 3.5 7.5 13.0 95
SRTC115S 445 5.0 0.50 12.5 3.5 7.5 13.0 130
SRTC36LH 150 10.0 0.50 23.0 5.0 8.0 29.0 36
SRTC60LH 230 10.0 0.50 23.0 5.0 8.0 29.0 60
SRTC75LH 330 10.0 0.50 23.0 5.0 8.0 29.0 95
SRTC115LH 450 10.0 0.50 23.0 5.0 8.0 29.0 130
Technical Information
A range of high tensile cable ties with exceptional resistance to both weathering andageing. The ties have a high resistance to corrosion and chemical attack, with specialdurability against salt water and spray. TheA.I.S.I. 316 stainless material can achieve veryhigh working temperatures and these are as indicated in Table 1. In order to achieve evenhigher degrees of protection some of the tiescan be coated with a matt heat resisting polysetser powder.
From Table 1 you will notice that the coatingdoes restrict the working temperature, butenhances durability, for specification and testof the coating see Table 2.
The ties are supplied in three designs: 1. Roller Ball Type2. Ladder Type 3. Releasable
Stainless Steel cable ties can be used in manyvaried applications of extreme mechanical,chemical, radiation and temperature environments such as aircraft, power plants,mines, tunnels, oil and gas platforms.
TABLE 1 (TEMPERATURE RATING)
TYPE DESCRIPTION WORKING TEMPERATURECOATED UNCOATED (NATURAL)
SRBT ROLLER BALL (NATURAL) - -80 DEG C to 540 DEG C
SLT LADDER (NATURAL) - -80 DEG C to 540 DEG C
SLTC LADDER (COATED) -80 DEG C to 150 DEG C
SRTC RELEASEABLE (COATED -80 DEG C to 150 DEG C
TABLE 2 (COATING) PROPERTIES
MATERIAL HT POLYESTER POWDER COATTHICKNESS 50 MICRONS
CHEMICAL AND DURABILITY TESTS
Salt Spray ASIM B1117 AT 35 Deg C Pass at 250 HRS. No Corrosion or Creep
Cyclic Humidity Pass at 100 HRS. No Blisteringor loss of gloss
Exterior durability Excellent. Non chalking, slight loss ofgloss after continous exposure butno breakdown or reduction inproductive properties
Colour stability at elevated Excellent for continuous temperatureselevated temperature up to 150 Deg C
Chemical resistance Generally good to acids, alkalinesand oils at normal temperature
S = STANDARD DIMENSION A NOMINAL DIMENSION D NOMINALLH = LIGHT HEAW DIMENSION B + - 0.4mm DIMENSION E NOMINALALL DIMENSIONS ARE IN mm DIMENSION C + - 0.04mm DIMENSION F NOMINAL
STAINLESS STEEL RELEASABLE CABLE TIE
68
Electrical Accessories
DSTG1 – STAINLESS STEEL CABLE TIE GUN
Specification
Length: 178 x 140 x 29 (mm)Weight: 560gStainless Steel Tie: Thickness up to 0.3mm
Width up to 7.9mm
TENSION SETTING TENSION APPLIED (Min)Kgs
1 31.52 47.03 58.74 65.0
FASTEN AND AUTOMATIC CUT MECHANISM
SuitabilityFor use on natural or coated stainless steel roller ball orladder type cable ties.
DSTG2 – Stainless Steel Cable Tie Gun
SuitabilityFor use on natural or coated stainless steel roller ball orladder type cable ties.
Application Method For Product DSTG2
A. Place the tie around the object to be secured.B. Insert the tail through the slot and into the ratchet
jaw and tension by repeatedly pressing the tool handles together.
C. After tensioning, move the tool with an up and downaction and twist the tool in a clockwise direction. Thiswill shear off the tail adjacent to the cable tie head.
DSTG2 – STAINLESS STEEL CABLE TIE GUN
70
Electrical Accessories
The Mark-On cable marking system is a real timeand money saver. It consists of a handy dispenserwith tear off mechanism filled with 10 rolls ofself adhesive vinyl cloth tape. (one roll each 0–9).
Rolls are 5mm wide and 2.4 metres long withapproximately 500 markings.
Temperature Range: 29°C to +93°C.Tape Colour: White Yellow available on request.Refills supplied in bags of 10 rolls.
Range of products allows you to choose the exactcombination of markers for your problem.Numbers: O–9
CABLE MARKING SYSTEMS
• Strong Transparent Shells are larger than normal to allow plenty of room for jointing.
• Easy Mix Twin Pack Quality Polyurethane Resin has a minimum two year shelf life.
• Have sufficient quantity of resin in the kits so extra bags to top up are not required.
• Kits are complete with earth continuity, safety gloves, step by step instructions.
• Mechanical connectors can be supplied for any combination of cable in kits so that the kit is complete and ready for customer to utilise.
• Technical staff are available at all times to answer your queries quickly and efficiently.
CABLE JOINTING KITS AND ACCESSORIES Snaplock Shell
Larger Shell
96
Heatshrink Tubing and Accessories
Mini Reel Packs
Commercial Grade Polyolefin can be supplied on mini reels. It canbe used to provide insulation for electrical connections, components and wiring. This tubing has a minimum shrink temperature of 120°C. Higher temperatures may be used withoutdamaging the tubing, if rapid shrinking is required.
Type HST
• Shrink Ratio 2:1• Operating Temperature Range -55°C to 135°C• Shrink Temperature 100°C• Suitable for general use on high quality equipment requiring
military / UL approval
TECHNICAL FEATURES
Continuous Operating Temperature Range: -55 to 135 °CShrink Ratio: 2 : 1Flammability: Self ExtinguishingBase Material: PolyolefinShrink Temperature: >120°C
PART No. ORDERING SIZE MINIMUM EXPANSION MAXIMUM RECOVERED NOMINAL RECOVERED WALL
Ordering Data Type HST
TO COMPLIMENT THE HEATSHRINK TUBE PRODUCTS, DAVICO CAN SUPPLY A COMPLETE RANGE OFHEATSHRINK COMPRESSION TERMINALS AND TOOLING.
ins mm ins mm ins mm ins mm
HST 1.2 3/64 1.2 0.046 1.2 0.023 0.6 0.018 0.45HST 1.6 1/16 1.6 0.063 1.6 0.031 0.8 0.018 0.45HST 2.4 3/32 2.4 0.093 2.4 0.046 1.2 0.019 0.50HST 3.2* 1/8 3.2 0.125 3.2 0.062 1.6 0.019 0.50HST 4.8* 3/16 4.8 0.187 4.8 0.093 2.4 0.019 0.50HST 6.4* 1/4 6.4 0.250 6.4 0.125 3.2 0.026 0.65HST 9.5* 3/8 9.5 0.375 9.5 0.187 4.8 0.026 0.65HST 12.7* 1/2 12.7 0.500 12.7 0.250 6.4 0.026 0.65HST 19.1* 3/4 19.1 0.750 19.0 0.375 9.5 0.029 0.75HST 25.4* 1 25.4 1.000 25.4 0.500 12.7 0.035 0.90
Colour: Black, Red, Yellow, Blue, White, Green / Yellow, Grey, BrownNote: Green / Yellow only available in sizes marked*
Display Stands Single Packs