• Heat-shrinkable composite joint closure system for cables: aerial, buried orducted, non filled or jelly filled, withpolyethylene, lead, steel or aluminiumsheaths

• Composite structure of the sleeve offersan excellent resistance to mechanicalabuse during and after the installation

• Integrated moisture barrier reconstitutesthe cable sheath over the total splicearea

• Hot-melt adhesive forms a watertightseal to the cable sheath

• Variable non-hygroscope liner insulates,shapes and mechanically protects the splice bundle

• Excellent performance under highhumidity and in tropical conditions

• Up to 3 cables at each end can beaccommodated using three finger clipswith hot-melt adhesive

• Installation indicators: heat-sensitivepaint, adhesive flow and white line

• Extended size range can accommodatesplices up to 800 pairs

• Unlimited shelf life

XAGA 530Joint closure system for unpressurized copper networks

Jonathan HewittJJH

Tyco Electronics Raychem bvbaDiestsesteenweg 6923010 Kessel-Lo, BelgiumTel 32-16 351 011 (USA)1-919-557-8900Fax 32-16 351 697 (USA)1-919-557-8498www.tycoelectronics.comwww.telecomosp.comTC 310/DS/4 10/98

Tyco Electronics, TE logo and XAGA are trademarks.

The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, Tyco Electronicsmakes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. Tyco Electronics’ obligations shall only be as set forth in Tyco Electronics’Standard Terms and Conditions of Sale for this product and in no case will Tyco Electronics be liable for any incidental, indirect or consequential damages arising out of the sale,resale, use or misuse of the product. Users of Tyco Electronics products should make their own evaluation to determine the suitability of each such product for the specific application.

XAGA 530 kit content

• Heat-shrinkable sleeve• Channels with underclip • Flexible liner• Cleaning tissue• Abrasive strip• Desiccant (Silica gel)• Aluminium foil• Branch-off kit• Shield continuity wire• Installation procedure

* Note for branched joints

1 The standard XAGA 530 kit is designed for max. 2 cables branched at one end only.Branched joints with more cables require the use of one additional branch-off kit(BOKT-5S or 5M) per added cable.

BOKT kit content• Branch off clip• Shield continuity clip + connector• Cleaning tissue• Aluminium foil• Tie wrap

Sizing/ordering informationDescription BOKT kit

BOKT-5S-43/8-75/15 XAGA 530-43/8-xxx and XAGA 530-75/15-xxxBOKT-5M-92/25-125/30 XAGA 530-100/25-xxx and XAGA 530-125/30-xxx

2 For joints with 2 or more cables in oneend the overall diameter must bedetermined.Add 6 mm for every small clip or 8 mm forevery medium clip. In each case the totaldiameter may not exceed the maximum jointOK diameter. See below.

Effective diameter 50 mm

Clip Clip

20 mm 10 mm 8 mm

Use kit XAGA 530-75/15-xxx depending thejoint length.

* Note for filled joints (optional)A special filling compound RSS and filling kitcomponents are available. Tyco Electronicsdescription XAGA-530-xx/xx-xxxS

Description Splice bundle Cable Max. joint Overall joint Branch-offdia. D max. dia. D min. gap L length S kit (BOKT)

XAGA 530-43/8-150 43 8 150 350 smallXAGA 530-43/8-300 43 8 300 500 smallXAGA 530-55/12-150 55 12 150 360 smallXAGA 530-55/12-300 55 12 300 510 smallXAGA 530-75/15-240 75 15 240 450 smallXAGA 530-75/15-300 75 15 300 510 smallXAGA 530-75/15-400 75 15 400 630 smallXAGA 530-75/15-450 75 15 450 670 smallXAGA 530-100/25-250 100 25 250 580 mediumXAGA 530-100/25-450 100 25 450 760 mediumXAGA 530-100/25-600 100 25 600 930 mediumXAGA 530-125/30-250 125 30 250 600 mediumXAGA 530-125/30-450 125 30 450 760 medium

Sizing/ordering information(dimensions in mm)

Jonathan HewittJJH