Specifications subject to change without notice. The information in this document does not form part of any quotation or contract

Page 1 www.comrod.com

AMX91 9.1m (30ft) Composite Man-Portable Sectional Mast

AMX91.pub (01/22-1)

The AMX91 is an 9.1 metre (30 ft) tactical lightweight composite sectional mast designed to be carried and deployed by a single person. The mast can be erected in a matter of minutes and can support lightweight top loads such as antennas or sensors. • 9 lightweight composite sections, 1.1 m (43 in)

long. Tube outside diameter Ø44.5 mm (1.75 in)

• Halyard cleat on one mast section for raising wire antennas. Optional lanyard for raising wire antennas

• Mast sections fit together to lock azimuth rotation. Enables the use of directional antennas.

• Two level, four way rope guys

• Packs down into a single, easy to carry case

• Quickly and easily deployed by a single person.

• Maintenance free composite glass fibre construction.

• Highly resistant to corrosion. Suitable for marine or coastal environments.

Guy locking ring and top load interface spigot

Ø39mm OD x 100mm long

Baseplate Assembly

Guy Winders and Stake

Mast sections fit together to lock azimuth rotation

AMX91-MIL-SD-0001

Mast section with Halyard cleat

Specifications subject to change without notice. The information in this document does not form part of any quotation or contract

www.comrod.com Page 2

Mechanical Specification

Mast sections Fibreglass tube outside diameter Ø44.5 mm, 1000 mm long with 100 mm aluminium spigot. Olive drab lacquer finish. 9 pcs (one with halyard cleat).

Total Kit Weight 15.6 Kg (24 lbs)

Top Interface Ø39 mm OD spigot, 100 mm long (to fit 40 mm socket)

Guys Top - 4 pcs, 3 mm braided rope on winder with adjustable lock and snap hooks each end. Middle - 4 pcs, 3 mm braided rope on winder with adjustable lock and snap hooks each end.

Guy pegs 6 pcs powder coated steel.

Base support Fibreglass with spikes and peg down loop.

Top load (Max) 6.0 kg (13 lbs) *

Wind Speed (Max) 96 km/h (60 mph), including gust

Temperature range -55 °C, +55 °C; -67 °F, +131 °F

Standard Kit List

1

3

8

6

7

10

11

9

Part Item Qty Dimensions / Weights

Mast section 1 8 1.0 kg

Mast section with cleat 2 1 1.0 kg

Upper guy rope with winder 3 4 0.2 kg

Middle guy rope with winder 4 4 0.2 kg

Lanyard (*optional) 5 1 0.2kg

Guy Ring Locking 6 2 0.05 kg

Guy pegs 7 5 0.3 kg

Base support 8 1 0.2 kg

Hammer 9 1 1.2 kg

User Manual 10 1 A5 Booklet

Carrying bag 11 1 115 x 22 x 16 cm / 2.2 kg

* Subject to top load wind surface area.

4

2

5*

Specifications subject to change without notice. The information in this document does not form part of any quotation or contract

www.comrod.com Page 3

AMX91 Mast Options

Antenna Brackets Antenna brackets are available to mount Comrod monopole and dipole antennas onto the AMX91 mast. Antennas can be mounted on the top section and well as below the top load. Brackets are available to fit the standard Comrod VM or CEF type antenna interface connection. Please contact Comrod with your specific requirement.

Adaptor - Ø50mm Top load adaptor - Ø50mm OD (1,97 in) spigot, Ø40mm ID (1.57 in) socket

RF Cable Assemblies Comrod can supply RF cable assemblies to suit the customer requirement. Cables can be specified by cable type and length, connector type, strain relief etc. Please contact Comrod with your specific requirement.

160

mm

(6.

3 in

)

Ø50 OD spigot, Ø40 ID socket

Interface to top of AMX85 mast section

VM Connector

CEF Connector