Data sheet Sheet No.: DIMENSIONS AND TECHNICAL DETAILS

Data sheetSheet No.: Date: November 2009

EL MaticTMEL MaticTM

www.emerson.com/elomaticCopyright © Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/elomatic or from your nearest Actuation Technologies Center: America’s: +1 281 477 4100 (fax 477 2809) Europe: +36 22 530 950 (fax +36 22 54 37 00) Asia Pacific: +65 650 14 600 (fax +65 626 80 028)

A5.113 Rev. A DIMENSIONS AND TECHNICAL DETAILS - ELECTRIC ACTUATOR ELQ

M

O

V1

V2

øH

P4x W1

4x W2

D

C

A B F G

N

2x ‘E’

Visual position indication

Space for cover removal

Power supply terminal box

Entry "E"

Entries for control & feedback signals

Standard:Other drives optional

Dim. in inches ELQ100 ELQ200 ELQ300 ELQ500 ELQ800A 5.83 5.83 5.83 7.17 7.17B 5.79 5.79 5.79 7.36 7.36C 11.30 11.30 11.30 13.19 13.19D 3.94 3.94 3.94 3.94 3.94E 1/2" NPT 1/2" NPT 1/2" NPT 1/2" NPT 1/2" NPTF 4.65 6.14 6.14 8.62 10.08G 4.06 4.06 4.06 5.20 5.20H 4.92 4.92 4.92 6.89 6.89M 1.97 1.97 1.97 2.36 2.36N 3.94 7.09 7.09 11.81 15.75

O max. 0.748 0.748 0.866 1.063 1.417O min. 0.748 0.748 0.866 1.063 1.417

P 0.99 0.99 1.11 1.43 1.90V1 2.756 2.756 2.756 4.016 4.016V2 4.016 4.016 4.016 5.512 5.512W1 5/16-18 x .53 5/16-18 x .53 5/16-18 x .53 3/8-16 x .63 3/8-16 x .63W2 3/8-16 x .63 3/8-16 x .63 3/8-16 x .63 5/8"-11 x .98 5/8"-11 x. 98

DescriptionSeries ELQ electric actuators are powerful, 1/4 turn units with five sizes covering the torque range from 885 to 7081 In.lb. They incorporate High Ratio Drive (HRD) gearing which provides a compact backflash free reduction gear idealy suited for both tight positional control and long trouble free ON/OFF operation. Universal power control allows direct connection to all the usual voltages.The aluminum alloy housing contains the motor, gear reduction and the Electronic Control Unit (ECU). - Electronic control enables precise control of the actuators internal functions and a ready interface to a wide range of control options. Electronic torque control is included as a standard feature. Modulair construction is used throughout and allows for a wide range of “kit” and “factory” options.The manual override handwheel is constantly engaged, it is non-rotating and arranged so that at no time can be back driven by the motor. The handwheel is equipped with a spinner and so can be easily removed. The mounting/drive is to ISO 5211.

SpecificationNominal Rotation : 90° - Analogue adjustable from 10° up to 100° of strokeEnclosure : IP65 / NEMA 4Temperature : -4°F to +158°FElectrical Entry : 3 x 1/2” NPT (Option M20 x 1.5 )Electrical Connection : By internal terminal block- Power supply : AC - 115V, 230V, or 400V (+10% / -6%) 50/60 Hz : DC - 24V (±10%)- Control signal : 24VDC (±10%)- Limit Switches : 2 x SPDT, Micro switches (500mA at 30 VDC/VAC)Torque Control : ElectronicDuty cycle : 100%Mechanical Stops : At 0° and 90°, adjustable +/- 10°Heater : Standard, 10 WattVisual Indication : By raised dome on top coverFinish : Two component polyurethane coatingMaterials : Housing : Aluminum alloy : External Steel Parts : Stainless Steel

Kit options• Position control• Extra limit switches • Position transmitter• Local control station • Speed control• Status option

Factory options• IP68• Explosion proof

ATEX or FM• High temperature• Low temperature• Bus communication:

Fieldbus Foundation

Performance ELQ100 ELQ200 ELQ300 ELQ500 ELQ800Torque (In.lb.) 885 1770 2655 4425 7081

Speed/90° (Sec.) Max. load 10 14 18 22 36No load 6 8 13 17 28

Power Supply 115VAC 1 1 1 1.7 1.7Max. Current (A) 230VAC 0.5 0.5 0.5 0.9 0.9Max. 400VAC 0.3 0.3 0.3 0.5 0.5

24V DC 4.1 4.3 4 5.3 5.1Power (W) Nominal 98 102 96 130 125Weight (lb.) 29 31 32 62 66

Data sheetSheet No.: Date:



December 2011A5.115 Rev. C DIMENSIONS AND TECHNICAL DETAILS - ELECTRIC ACTUATOR ELQ-XP ATEX

D

C

A B

2x 'E'

F G

N

P

V1

V2

øHøH

4x W1

4x W2

M

O


Power supplyterminal box



Entry "E"


DescriptionSeries ELQ FM electric actuators are powerful, 1/4 turn units with five sizes covering the torque range from 885 to 7081 In.lb. They incorporate High Ratio Drive (HRD) gearing which provides a compact backflash free reduction gear idealy suited for both tight positional control and long trouble free ON/OFF operation. Universal power control allows direct connection to all the usual voltages.The explosionproof housing contains the motor, gear reduction and the Electronic Control Unit (ECU). - Electronic control enables precise control of the actuators internal functions and a ready interface to a wide range of control options. Electronic torque control is included as a standard feature. Modulair construction is used throughout and allows for a wide range of “kit” and “factory” options.The manual override handwheel is constantly engaged, it is non-rotating and arranged so that at no time can be back driven by the motor. The handwheel is equipped with a spinner and so can be easily removed. The mounting/drive is to ISO 5211.

SpecificationNominal Rotation : 90° - Analogue adjustable from 10° up to 100° of strokeEnclosure : IP67 according to IEC 60529Explosion proof : II 2 G Ex db IIB T4, acc. to EN60079-1 and EN60079-0Certificate nr. : KEMA 03ATEX2128XTemperature : -4°F to +140°FElectrical Entries : 3 x 1/2” NPT (Option M20 x 1.5)Electrical Connection : By internal terminal block.- Power supply : AC - 115V, 230V, or 400V (+10% / -6%) 50/60 Hz : DC - 24V (±10%)- Control signal : 24VDC (±10%)- Limit Switches : 2 x SPDT, Micro switches (500mA at 30 VDC/VAC)Duty cycle : 100%Torque Control : ElectronicMechanical Stops : At 0° and 90°, adjustable +/- 10°Heater : Standard, 10 WattVisual Indication : On top coverFinish : Two component polyurethane coatingMaterials : External Steel Parts : Aluminum alloy : Housing : Stainless Steel

Kit options• Position control• Extra limit switches• Position transmitter • Local control station• Speed control• Status option

Factory options• IP68• Low temperature• Fieldbus Foundation™

Bus Communication






O max. 0.752 0.752 0.871 1.068 1.424O min. 0.748 0.748 0.866 1.063 1.417

P 0.99 0.99 1.11 1.43 1.90V1 2.756 2.756 2.756 4.016 4.016V2 4.016 4.016 4.016 5.512 5.512W1 5/16-18 x .53 5/16-18 x .53 5/16-18 x .53 3/8-16 x .63 3/8-16 x .63W2 3/8-16 x .63 3/8-16 x .63 3/8-16 x .63 5/8"-11x .98 5/8"-11x .98




November 2010A5.115.2 Rev. B DIMENSIONS AND TECHNICAL DETAILS - ELECTRIC ACTUATOR ELQ XP FM

D

C

A B

2x 'E'

F G

N

P

V1

V2

øHøH

4x W1

4x W2

M

O


Power supplyterminal box



Entry "E"


DescriptionSeries ELQ FM electric actuators are powerful, 1/4 turn units with five sizes covering the torque range from 885 to 7081 In.lb. They incorporate High Ratio Drive (HRD) gearing which provides a compact backflash free reduction gear idealy suited for both tight positional control and long trouble free ON/OFF operation. Universal power control allows direct connection to all the usual voltages.The explosionproof housing contains the motor, gear reduction and the Electronic Control Unit (ECU). - Electronic control enables precise control of the actuators internal functions and a ready interface to a wide range of control options. Electronic torque control is included as a standard feature. Modulair construction is used throughout and allows for a wide range of “kit” and “factory” options.The manual override handwheel is constantly engaged, it is non-rotating and arranged so that at no time can be back driven by the motor. The handwheel is equipped with a spinner and so can be easily removed. The mounting/drive is to ISO 5211.

SpecificationNominal Rotation : 90° - Analogue adjustable from 10° up to 100° of strokeExplostion proof : Class 1, Div. 1, Groups C/D, NEMA 4Certificate : Factory Mutual Approval report J.I. 3D6A1.AETemperature : Class T4; -40°F to +140°FElectrical Entry : 3 x 1/2” NPTElectrical Connection : By internal terminal block- Power supply : AC - 115V, 230V, or 400V (+10% / -6%) 50/60 Hz : DC - 24V (±10%)- Control signal : 24VDC (±10%)- Limit Switches : 2 x SPDT, Micro switches (500mA at 30 VDC/VAC)Duty cycle : 100%Torque Control : ElectronicMechanical Stops : At 0° and 90°, adjustable +/- 10°Heater : Standard, 10 WattVisual Indication : On top coverFinish : Polyurethane paintMaterials : External Steel Parts : Stainless Steel : Housing : Aluminum alloy

Kit options• Position control• Extra limit switches• Position transmitter • Local control station• Speed control• Status option

Factory options• IP68• Low temperature• Bus communication:

Profibus DP or Fieldbus Foundation


O max. 0.752 0.752 0.871 1.068 1.424O min. 0.748 0.748 0.866 1.063 1.417

P 0.99 0.99 1.11 1.43 1.90V1 2.756 2.756 2.756 4.016 4.016V2 4.016 4.016 4.016 5.512 5.512W1 5/16-18 x .53 5/16-18 x .53 5/16-18 x .53 3/8-16 x .63 3/8-16 x .63W2 3/8-16 x .63 3/8-16 x .63 3/8-16 x .63 5/8"-11x .98 5/8"-11x .98








October 2010A5.301 Rev. B ELQ ACTUATOR WITH TWO EXTRA SWITCHES Q-XS2

-

+Vmax = 30 V DC/ACImax = 500 mA

1 10875 6432 9

2019181715 16141312

26 3736333230 31292827 342522 242321 35

111 10875 6432 9

2019181715 16141312

26 3736333230 31292827 342522 242321 35

11

Vmax = 30 V DC/ACImax = 500 mA

com

nc no

com

nc no

+

-

com

nc no

com

nc no

2

3

1

4

5

6

7

Act

uato

r w

iring

Fie

ld w

iring

Red cam"Closed"

Green cam"Open"

ClosedOpen

Act

uato

r w

iring

Fie

ld w

iring

Green cam"Open"

Red cam"Closed"

OpenClosed

Standard limit switches

Extra limit switches

DescriptionThis ELQ electric actuator option provides two extra single pole double throw limit switches for indicating the fully open and the fully closed actuator position. This option can be used when higher voltages than 24V are used for position indication, for instance 110V or 220V.

This option makes use of V3 type switches. As a variation of this option 3-wire proximity switches (V3 type) can be provided.

ConstructionThe kit is mounted on top of the mainboard (1). The switches are operated by their own cams (2) which are driven by the indicator shaft (3). The two switches on the top are the standard switches (6), the switches on bottom are the extra switches (7).

The ELQ-actuator has a yellow 6 pole connector (4) to connect the extra limit switches to the terminals in the terminal compartment. The connectors (5) for motor switches and standard limit switches can be plugged into the sockets on the mainboard.

Specifications Limit switches Extra limit switchesType : V3, mechanical V3, mechanicalVoltage : max. 30 VAC or DC max. 30 VAC or DCCurrent : 500mA at 30 VDC/VAC 500mA at 30VDC/VACTemperature : -4.0° to +158°F -4.0°F to +158°F

IdentificationFactory option : Add "+ Q-XS2" to the basic actuator size e.g. ELQ100 + Q-XS2Kit option : Actuator size is added to: "Kit Q-XS2" e.g. Kit Q-XS2/ ELQ100




A5.302 Rev. A ELQ ACTUATOR WITH POTENTIOMETER Q-POT

12 13 14 15 16 17 18 19 20

1 2 3 4 5 6 7 8 9 10 11

21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

5

1

3

4

2

10KOhm

UMax.30VDC

Actuatorpre-wiring

TERMINAL ON ELQ

Fieldwiring

DescriptionThis ELQ electric actuator option provides a varying indication of the actuator and valve position by means of an electrical potentiometer. When connected as shown a voltage signal will indicate an analog position.

ConstructionThe potentiometer (1) is mounted in the limit switch assembly (2) on top of the mainboard (3). The potentiometer is driven by the indicator shaft (4) and an intermediate gear in the limit switch assembly. The potentiometer connector (5) is plugged in the mainboard. The mainboard is prewired to the terminal strip in the terminal compartment.

SpecificationsVoltage : Up to 30VDCCurrent : 15 mA max.Power max. : 0.5 WTemperature : -4.0° to +158°FResistance : 10KW; (see variations)Type : PA11Linearity : 1 %Mechanical rotation : 300° ±5°Electrical rotation : 270° ±10°

IdentificationFactory option : Add "+ Q-POT" to the basic actuator size : eg. ELQ100 + Q-POTKit option : Actuator size is added to: "Kit Q-POT" : eg. Kit Q-POT / ELQ100

Variations1KOhm to 470KOhm

Note 1 When a combination of two options is needed, both of which need a feedback potentiometer,

the second plug from the double potentiometer can be used.




A5.304 Rev. A ELQ ACTUATOR WITH SPEED CONTROL OPTION Q-SC

DescriptionThis electric actuator option controls the speed of the ELQ-actuator. It has an electronic card and a feedback potentiometer. The electronic card is equiped with an initialization button, a potentiometer and a switch for speed range selection. A two speed range selection is made with a "linear/pulse" switch and further fine adjustment made by means of a potentiometer. The linear setting is for the "high" speed range (shorter cycle times) and the pulse setting is for the "low" speed range (longer cycle times).

ConstructionThe speed control card (1) is mounted on top of the mainboard (2). The feedback potentiometer (3) is mounted in the limit switch assembly (4) on top of the mainboard. The potentiometer is driven by the indicator shaft (5) and an intermediate gear in the limit switch assembly. The potentiometer connector (6) is plugged in to the speed control card.

SpecificationsTemperature : -4.0° to +158°F

IdentificationFactory Option : Add “+ Q-SC” to the basic actuator size : eg. ELQ100 + Q-SCKit Option : Actuator size is added to: “Kit, Q-SC” : eg. Kit, Q-SC/ELQ100

VariationsA combination of cards also can incorporate position transmitters, status information etc.

Note1 When a combination of two options is needed, both of which need a feedback potentiometer,


ImportantWith the speed control the cycle times can be fixed, this means that during the cycle time variations in the speed may occur, depending on the load.

Cycle times speed control option

Type Linear (sec) Pulse (sec)

Min. Max. Min. Max.

ELQ100 6 11 11 88

ELQ200 8 15 15 120

ELQ300 13 24 24 200

ELQ500 17 31 31 240

ELQ800 28 51 51 400

6

1

2

3

5

4




A5.305 Rev. A ELQ ACTUATOR WITH 4-20mA POSITION TRANSMITTER Q-PT

DescriptionThis ELQ electric actuator option provides a varying indication of the actuator and valve position by transmitting a 4- 20 mA signal, this is proportional to the output shaft. Feedback is reversable from a 4-20mA signal to a 20-4mA signal by means of a jumper setting (3).

This option consists of an electronic card and a potentiometer fed from an external (24VDC) power supply. The card is equipped with trimmers for zero (1) and span (2) adjustment. When mounted on top of the mainboard the option is connected to the terminal compartment by internal wiring.

ConstructionThe electronic card (4) is mounted on top of the mainboard (5). The potentiometer (6) is mounted in the limit switch assembly (7) and is driven by the indicator shaft (8) and an intermediate gear in the limit switch assembly. The potentiometer connector (9) is plugged in the mainboard. The mainboard is prewired to the terminal strip in the terminal compartment.

SpecificationsInput : 15 to 30 VDCOutput : 4 to 20 mA, with adjustable zero and spanTemperature : -4.0° to +158°FPotentiometer : 10KW; other values on requestVoltage drop : 2V max.Accuracy : 2 %

IdentificationFactory option : Add "+ Q-PT" to the basic actuator size : eg. ELQ100 + Q-PTKit option : Actuator size is added to: "Kit Q-PT" : eg. Kit Q-PT / ELQ100



4-20mA

Max. 30VDC

6

8

7

5

2

1

4

9

3

2 1

Actuatorpre-wiring

Fieldwiring

TERMINAL ON ELQ




A5.306 Rev. A ELQ ACTUATOR WITH POSITIONER Q-MOD

12 13 14 15 16 17 18 19 20

1 2 3 4 5 6 7 8 9 10 11

21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37

E- + R INIT

INIT

R+

-E

-

+

5

4

3

1

6

2

4-20mA0-10V

Actuatorpre-wiring

ELQ positionerboard

Fieldwiring

TERMINAL ON ELQ

DescriptionThis ELQ electric actuator option is the most advanced positioner available on the market today. This version is made possible by a combination of the latest developments in micro processor technology together with a low power interface for the ultimate in actuator control.

The positioner option provides a modulationg position control from an incoming 4 to 20 mA, 0 to 10VDC or digital signal. After initialization the micro processor senses what is required and sets it self up accordingly.

All the usual control characteristics are provided, these are easily reset from the five button control panel - Split range, equal percentage, quick opening and custom curves, direct/reverse acting.

ConstructionThe electronic card (1) is mounted on top of the mainboard (2). The potentiometer (3) is mounted in the limit switch assembly (4) and is driven by the indicator shaft (5) and an intermediate gear in the limit switch assembly. The potentiometer connector (6) is plugged in the positioner card. The mainboard is prewired to the terminal strip in the terminal compartment.

SpecificationControl input Signal : 2 wire 4 to 20 mA, 0 to 10VDC Max. resistance : 197Ohm for 4-20mA signal at 20mA : 498Ohm for 0-10V signalPerformance Min. deadband : 0.8% full scale Resolution : 10 bits A/DTemperature : -4.0° to +158°FAdjustable settings : Zero, range : Response characteristics : Split range : Custom curves : Action : Direct/Reverse action : Deadband

IdentificationFactory option : Add "+ Q-MOD" to the basic actuator size : eg. ELQ100 + Q-MODKit option : Actuator size is added to: "Kit Q-MOD" : eg. Kit Q-MOD / ELQ100






A5.307 Rev. A INSTALLATION OF SPRINGS OF P-SERIES ACTUATOR P

2.91”

6.38”

4.57”

3.19”

4.57”

OFF

CLOSEOPEN

LOCAL REMOTE

OFF

CLOSEOPEN

LOCAL REMOTE

2

1

42 3

Moto

r swi

tchCL

OSE

Moto

r swi

tchOP

EN

OPEN

Limit s

witch

CLOS

ELim

it swi

tch

O E

NEPC L OS

DescriptionThis ELQ electric actuator option provides a local control box. The box is equipped with buttons for "Local", "Remote", "Open" and "Closed". LED's indicate the "Local", "Remote" or the "Off" status.

When “LOCAL” is selected the valve may be moved to the "Open" or "Closed" position by pressing the "Open" or "Closed" button.

The "Open" and "Closed" buttons are locked out when “Remote” is selected and the control is returned to the remote control station.

The optional status module (see data sheet A5.308) can give a signal to the control room indicating that the ELQ-actuator is switched to local control.

ConstructionThe control box (1) is located on the side of the actuator casting. All the connection wiring is contained internally. The connector (2) is plugged in on top of the mainboard (3). The cover (4) may be locked by an optional pad lock.

SpecificationSwitches Temperature : -4.0° to +158°FHousing Material : Aluminum Finish : Two component polyurethaneEnclosure : : IP67Steel parts : Stainless steel

IdentificationFactory Option : Add “+ Q-LC” to the basic actuator size : eg. ELQ100 + Q-LCKit Option : Actuator size is added to: “Kit, Q-LC” : eg. Kit, Q-LC/ELQ100VariationsLocal control box with pad lock




A5.307.1 Rev. A ELQ ACTUATOR WITH LOCAL CONTROL STATION Q-LC Ex

DO NOT OPENWHILE

ENERGIZED

OPE

N CLOSE

CLOS

E

Moto

r swi

tch

OPEN

OPEN

CLOS

E

Limit s

witch

Moto

r swi

tch

Limit s

witch

LOCALCLOSE

REMOTELOCAL OFF

REMOTE

LOCALOPEN

DescriptionThis ELQ electric actuator option provides a local control box for use on explosion proof actuators.

The switch selects between “LOCAL OPEN”, “REMOTE”, “OFF”, “REMOTE” and “LOCAL CLOSE”. When in “LOCAL OPEN”, “LOCAL CLOSE” or "OFF" position the actuator can not be operated remotely.

This local control station is FM explosion proof certified and water and dust proof to IP67/NEMA4.

The optional status module (see data sheet A 5.308) can give a signal to the control room indicating that the ELQ-actuator is switched to local control.

ConstructionThe control box (1) is located on the side of an FM explosion proof actuator. All the connection wiring is contained internally. The connector (2) can be plugged in on top of the mainboard (3).Optional a pad lockable execution is available.

SpecificationTemperature : -4.0° to +158°FMaterial : AluminumFinish : Two component polyurethaneEnclosure : IP67/NEMA4Steel parts : Stainless steel

Explosion proofFatory Mutual (FM) : Class 1, Div. 1, Groups C/D, NEMA 4 : Certificate: Approval report J.I. 3D6A1.AE : Temperature: Class T4; -40°C to +60°C

IdentificationFactory Option : Add “+ Q-LC Ex” to the basic actuator size : eg. ELQ100 + Q-LC Ex

VariationsLocal control box with pad lock




A5.308 Rev. A ELQ ACTUATOR WITH STATUS MODULE Q-STM

DescriptionThis ELQ electric actuator option provides status information from the ELQ-actuator. Signals are provided for motor running, whether the ELQ-actuator is switched to the Local control box and if the power supply is properly connected. These signals or a combination of these signals can tell what is happening with the ELQ-actuator/valve unit.

ConstructionThe option consists of an electronic card (1) with three potential free contacts providing the signals and is mounted on top of the mainboard (2). The ELQ-actuator has an intermediate 6 pole connector (3) to connect the status module to the terminals in the terminal compartment.

SpecificationRelays : Potential free contactsVoltage : 0-30V DC/ACCurrent : 2 A max.

Signal StatusMotor running Contact closedSwitched to Local control Contact closedPower present Contact closed

IdentificationFactory Option : Add “+ Q-STM” to the basic actuator size : eg. ELQ100 + Q-STMKit Option : Actuator size is added to: “Kit, Q-STM” : eg. Kit, Q-STM/ELQ100

Moto

r swi

tch

CLOS

E

Moto

r swi

tch

OPEN

OPEN

Limit s

witch

CLOS

E

Limit s

witch

+

-

2

3

1

Motor running

Power supply connected

ELQ switched toLocal control station

Actuatorpre-wiring

Field wiring U-source

TERMINAL ON ELQ




A5.310 Rev. A ELQ ELECTRIC ACTUATOR WITH RELAY BOX Q-RB

Dim in mm. ELQ100 ELQ200 ELQ300 ELQ500 ELQ800A 205 205 205 258 258B 323 361 361 477 514C 120 120 120 120 120D 2x M20x1.5 2x M20x1.5 2x M20x1.5 2x M20x1.5 2x M20x1.5

DescriptionThis option provides two sets of relays for controlling and position indication of an ELQ electric actuator. These relays are suitable for high voltages or amperages, for instance 24VDC/5A, 48V/5A, 110V/2A or 220V/10A.

ConstructionThe relays are mounted in a relay box on the side of the ELQ-actuator. The relay box is connected to the terminal compartment by a pipe connection.

Control and feedback signals from the remote control system can be connected to the terminals in this box. The wiring of the relay box can be connected to the terminal compartment for 24V power supply, control- and feedback signals.

SpecificationsRelay type : Silver nickel contactControl and feedback : 24 VDC - 1200Ohm signal voltages : 48 VDC - 4170Ohm : 115 VAC - 50/60Hz : 230 VAC - 50/60HzCurrent max. : 10AElectrical entry : 2x 1/2"NPT (optional M20x1.5)Finish : Two component polyurethaneEnclosure : IP67Temperature : -40°F to +158°FHousing : Aluminum alloyCover : Aluminum alloy

Explosion proof - FM : Class 1, Div. 1, Groups C/D, NEMA 4 Certificate : FM Approval report J.I. 3D6A1.AE

IdentificationFactory option : Add "+ Q-RB-WP" or "+ Q-RB-XP" and voltage to the basic actuator size

e.g. ELQ100 + Q-RB-WP / 115 VACKit option : Actuator size, electrical entry dimension and voltage are added to:

"Kit Q-RB-WP" or "Kit Q-RB-XP" e.g. Kit Q-RB-WP / ELQ100 / 1/2'NPT / 115 VAC

: Note: Explosion Proof version only as factory option available

OptionsOther voltages, Q-XS2 for extra feedback signals

BA

D

C

D

65

43

21

87

2 110 9

O

ES

LCN

E

PO

109876542

201918171615141312

111

27 37363534333231302928262524232221

3

65

43

21

87

91012

FC

12345678

123456789

10

11

Feedback "Closed"

Feedback "Open"

Control signal "Close"

Control signal "Open"

Relay box for control and feedback signals

Wiring in terminal compartment

GreenGray

Black for NCBlack for NO

Red for NCRed for NOBrownPurpleWhiteBlue

Wiring in Relay box

Documents

Data sheet Sheet No.: DIMENSIONS AND TECHNICAL DETAILS