Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Data SheetSS/S264_8
■ Wide range of remote seal types- allow optimum design for each application
without compromise of performance
■ Large selection of options, materials and fillfluids- meet nearly all process requirements
■ All welded constructions- combine an economically feasible and technically
sound solution ensuring total reliability at linepressure down to full vacuum
■ Special designed remote seals for individualprocess solutions- add flexibility for most demanding services
2600T Series Pressure Transmitters
Models S264 Remote Seals
ABB 2600T SeriesEngineered solutions
for all applications
2600T Pressure TransmittersModels S264 SS/S264_8
2
Remote Seals OverviewThe S264x seals are used in combination with 2600T transmitters,allowing differential, gauge or absolute pressure measurements.Connection of the seal(s) to the relevant transmitter can beachieved as follows :- directly mounted with a short capillary connecting the "integral"
seal to the transmitter sensor;- through a capillary system which link the transmitter sensor to
a "remote" seal of any version.Using remote seal the transmitter can be selected with- two seals using same fill fluid, capillary and diaphragm size- one seal having the other side configured with a process flange
for wet/dry leg connection or a blind flange providing vacuum oratmospheric reference.
Model 264HR/NR transmitters have always one remote seal only,with a selectable reference to atmosphere or vacuum respectivelyfor gauge or absolute pressure measurements.The S264x Series Seal System is a protective device used toisolate 2600T series transmitters from the process fluid.The seal system provides a flexible diaphragm seal between theprocess fluid and a liquid filled capillary tube connected to thebody of the transmitter. The diaphragm isolates the process fluidwhile the filled capillary tube hydraulically transmits the processpressure to the transmitter sensor. The capillary of remote seal iscorrosion-resistant with robust costruction in stainless steel withspiral armour protection, also PVC jacket; PVC protection isalways recommended except for high temperature application,where stainless steel armour is suggested.The all welded construction assures reliable operation over thewidest range of operating temperature and under vacuumconditions.For certain applications, use of seal is necessary to prevent theprocess fluid from leaving its enclosure, due to reasons such as :• the process fluid has solids in suspension or is highly viscous
and can foul impulse lines.• the process fluid can solidify in impulse lines or the
transmitter.• the process fluid is too hazardous to enter the control area
where the transmitter is located.• the process temperature exceeds the recommended limits
for the transmitter.• the application is interface level or density measurement.
Remote seals offer the required constant and equal specificgravity of the pressure transfer fluid on the high and low sidesof the transmitter.
• the transmitter must be located away from the process foreasier maintenance.
The S264x series is available with process connections for ASMEor EN pipe flanges, wedge flow elements, chemical tees, andthreaded pipe fittings. Extended diaphragm remote seals,suitable for connection to 2in - 3in or 4in flanged tank nozzles orflanged tees, permit the seal diaphragm to be located flush withthe inside of a tank or pipe. Sanitary type seals meet the stringentrequirements of sanitary food, dairy, pharmaceutical and BioTech applications, offering FDA approved fillings and compliancewith 3-A Sanitary Standards.Fill fluids with FDA are defined as food fills and are GenerallyRecognized As Safe (GRAS) by the US Food and DrugAdministration (FDA).
Seal system selection criteriaApplication of an S264x system in direct mount or remote sealconfiguration to 2600T transmitters affects performances oforiginal devices. Effects are evident in:- Accuracy- Temperature effects- Dynamic response
• AccuracyAccuracy is only marginally affected when seal diaphragmstiffness is relevant compared with sensor stiffness. This is theonly characteristic of the S264x system which has role onaccuracy performance. High stiffness of diaphragm associatedwith low URL might produce increased errors of linearity,hysteresis, and long term stability; when diaphragm stiffness isaccuracy related also temperature effects are significantlyaffected. Some basic considerations on diaphragm stiffness helpunderstanding effects introduced by S264x system associatedwith transmitters. This is physically defined by the ratio betweenthe pressure variation applied to the diaphragm and thecorresponding volume variation. The stiffness is not linear alongthe whole diaphragm volumetric displacement, but the S264xdesign is such to maintain the system linear within the serviceconditions of the transmitter such as:- Operating pressure range- Operating static pressure (for differential transmitters)- Ambient & process temperature limitsDiaphragm stiffness is a function of material & thickness (elasticcoefficient), diameter (type), convolution shape and geometry(design defined)
• Temperature effectsS26 system has effect on temperature performance of the com-plete transmitter. This effect is mostly on zero of the instrumentand is produced by the expansion of the fill fluid into the closedvolume formed by the transmitter flange cavity the capillaryvolume and the remote seal volume. This volume filled with a fluidwith specific expansion coefficient; change in temperature of themeasuring device produce a volume variation which is absorbedby the remote diaphragm, whose stiffness produces a change inthe fluid pressure: this is the zero error. In real application thetransmitter/seal system is not the same and stable temperature.Therefore the errors referred in this document for each type ofdiaphragm and different fluids should be taken as a reference forqualitatively evaluation and not a true behaviour in normalapplication conditions. Should again be recognized that thestiffness of diaphragm and in this case, the thermal coefficient offluid are the parameter to take into account.
• Time responseApplication of S264x seal to transmitters increases the originaltime response. The amount of the increase depends from thenumber of elements and condition of the instrument as follows :- transmitter sensor range- physical configuration (i.e. a remote seal on other side)- type of measure/number of seal (one or two)- fill fluid viscosity of the S264x system applied- ambient temperature (affects the transmitter and the capillary)
and process temperature on the seal diaphragm- capillary length
2600T Pressure TransmittersModels S264 SS/S264_8
3
The delay introduced by the seal may be considered as an addedconstant time to the one of the associated transmitterFor obtaining the best application solution :• choose sensor code with URL closest to application SPAN• select largest diameter diaphragm seal related to URL.• keep the capillary length as short as possible• select the fill fluid that suits the most extreme process
conditions expected (highest temperature and lowestpressure) and it is compatible with the process fluid.
• In vacuum application, choose always the all welded versionand mount the transmitter primary 30 cm/12 inches or morebelow the bottom seal connection.
• In a two-seal system use the same diaphragm size, capillarylength and fill fluid on each side of the transmitter.
Ordering InformationThe transmitter and each seal system are each identified by aproduct code number. These code numbers are stamped on thetransmitter nameplate and each character identifies specificproduct features. Refer to ordering information for a detailedexplanation of the product code numbers.A typical example of the product code stamping is as follows :
Transmitter Product Code 264DRFSSA1AH–V1E1D3Seal System Product Code S264WHBCDFSBES1NNN
Industrial application in chemical, sanitary, food and any otherprocess industries may require seal configurations and/orprocess connection different from those reported in thisdocument. Each “special” should be evaluated by ABB to checkthe correctness and its level of functionality. Ask for the “S264xseries seal form” to define precisely the measuring problem andapplication requirements.
The following table shows the types of standard seals consideredin this leaflet. The mnemonics will be used as shortest crossreferences with the transmitter data sheet which should be read inconjunction with this data sheet.
ABB can also cooperate with you by developing a special remote seal for problems requiring individual solutions.
PLEASE CONTACT YOUR LOCAL ABB OFFICE OR REPRESENTATIVE FOR ADDITIONAL INFORMATION, SPECIFIC SEAL DATAAND APPLICABILITY.
Absolute viscosity (cP) = Kinematic Viscosity (cSt) x Specific gravity at specified temperature.The absolute viscosity value is used for response time calculation.
SEALS DIMENSIONS ON FOLLOWING PAGES ARE IN mm (in)
FILL FLUID CHARACTERISTICS (Table A)
ledoM epytlaeS eziS cinomenM
W462SrefaW
)doof(refaW
1 1/2 04ND/ni05ND/ni208ND/ni3
5.1P2P3P
C462SeetlacimehC
degnalfni3 3P
A462SE462SG462SR462S
degnalFmgarhpaidhsulftnioJgniRosla(
)dradnatsSIJdna
-1 1/2 )ylnoJREMSA(ni05A/05ND/ni2
/001-08ND/ni4-3001-08A
5.1P2P3P
degnalFdednetxemgarhpaid
05ND/ni208ND/ni3001ND/ni4
2E3E3P
U462S noinU 1 1/2 ni 5.1Z
T462S enil-ffodedaerhT 2 1/2 ni 5.2T
M462S enil-ffodegnalF 2 1/2 ni 5.2T
S462S
tunnoinUpmalcirT
lerruByrrehCcitpesA,yratinaS
05F/ni208F/ni3
ni4
2S3S3S
B462S nottuB ni1 1B
P462SecivresaerU
degnalf1 1/2 ni2 1/2 ni
5.1U5.2U
SDIULFLLIF)NOITACILPPA(
SNOITIDNOCGNITAREPO )F°77(C°52TANOITACIFICEPS
xamTfo>sbaP@
nimPsbarabm
)aisp(
xamTnimP@
nimT cificepSytivarg
citameniKytisocsiv
)tSc(
lamrehTnoisnapxe
01x( 3- )C°/™002CD-lioenociliS
)esopruplareneG()093(002rabm53@
7.0)10.0(
061)023(
04–)04–(
439.0 01 80.1
™041NA-lioenociliS)erutarepmethgiH(
)617(083rab1@
7.0)10.0(
003)275(
5–)32+(
70.1 04 46.0
™TLXmrehtlyS–remyloPenociliS)erutarepmetwoL(
)212(001rabm011@
2)30.0(
02)86(
001–)841–(
258.0 4.1 1
™02-MeeboeN-lioelbategeVADF)yratinaS-dooF(
)093(002rab1@
031)9.1(
051)003(
81–)0(
29.0 8.9 2.1
)%07(retaWnirecylGADF)yratinaS-dooF(
)002(39rab1@
0001)5.41(
39)002(
7–)02+(
80.1 2.2 63.0
™28LOCRAM-liolareniMADF)yratinaS-dooF(
)093(002rabm002@
33)5.0(
04)401(
04–)04–(
48.0 62 40.1
™nedlaG–trenI)ecivreSnegyxO(
)023(061rab1@
2)30.0(
07)851(
02–)4–(
28.1 4.4 1.1
2.4™nobracolaH–trenI)ecivreSnegyxO(
)653(081rabm004@
4)60.0(
07)851(
02–)4–(
78.1 3.6 468.0
2600T Pressure TransmittersModels S264 SS/S264_8
4
S264W Model Wafer Remote SealThe wafer remote seal is designed to be clamped between two ASME or EN raised face flanges. The diaphragm side of the seal facesthe process flange and a blind back-up flange is used on the other side of the seal.The wafer variant is also available as food design for 11/2in and 3in sizes.
134
(5.3
)
B
A /
A1
C
D
Flushing ring(OPTION)
25 (0.98) for 1/4 NPT
33 (1.30) for 1/2 NPTflushing thread(s)
Capillary toinstrument
Capillary toinstrument
Gasket seat finish
23 (0.9);25 (0.98)
for 1-1/2in food
eziS
)ni(mmSNOISNEMID
)aid(A.hpaid
1AgnihsulF
.aid.tnignir
)aid(B C D
1 1/2 ni )79.1(05 )50.2(25 )78.2(37 )20.3(8.67
6.1)60.0(
ni2 )63.2(06 )44.2(26 )26.3(29 )77.3(8.59
ni3 )5.3(98 )26.3(29 )5(7218.031)51.5(
04ND )79.1(05 )50.2(25 )64.3(88 )26.3(29
3)21.0(
05ND )63.2(06 )44.2(26201
)20.4()71.4(601
08ND )5.3(98 )26.3(29831
)34.5()95.5(241
1 1/2 ni)doof(
)79.1(05 )50.2(25 )78.2(37 )20.3(8.67 .A.N
ni3)doof(
)5.3(98 )26.3(29 )5(7218.031)51.5(
7.3)51.0(
2600T Pressure TransmittersModels S264 SS/S264_8
5
Maximum Working Pressure
WAFER SEAL ELEMENT : 16 MPa, 160 bar, 2320 psi but notgreater than the backup flange rating (not supplied).
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Minimum pressure with tantalum diaphragm is 1kPa abs, 10mbar abs,0.15psia.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
260°C (500°F) for Tantalum diaphragm.
204°C (400°F) for use with Teflon anti-stick coating.
320°C (608°F) for AISI gold plated diaphragm.
Limits for gaskets of flushing rings
Gasket seat finish
Smooth (ASME or EN): 0.8µm (Ra)
Serrated (ASME): 3.2 to 6.3µm (Ra)
Serrated (EN 1092-1 Type B1; up to PN40): 3.2 to 12.5 µm (Ra)
Serrated (EN 1092-1 Type B2; PN63 - 100): 0.8 to 3.2 µm (Ra)
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a seal ofspecific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES
eziSlaeSrefaW rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
1 1/2 04ND/ni Hni5.3,rabm7.8,aPk78.0 2O Hni2.1,rabm3,aPk3.0 2O Hni6.3,rabm9,aPk9.0 2O
05ND/ni2 Hni61.1,rabm9.2,aPk92.0 2O Hni82.0,rabm7.0,aPk70.0 2O Hni8.0,rabm2,aPk2.0 2O
08ND/ni3 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
lairetaM erusserP).xam(
erutarepmeT).nim().xam(
timilTxP
kcolraG,rab96,aPM9.6
isp0001C°402
)F°004(C°37–
)F°001–(000052
)ispxF°(
etihparG,rab52,aPM5.2
isp263C°083
)F°617(C°001–
)F°841–(
EFTP,rab06,aPM6
isp078C°052
)F°284(C°001–
)F°841–(
2600T Pressure TransmittersModels S264 SS/S264_8
6
BASIC ORDERING INFORMATION model S264W Wafer Remote SealSelect one character or set of characters from each category and specify complete catalog number.
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 W X X X X F X X X X X d'tnoC
laeSetomeRrefaW
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
metsysgniretneC 7– ht retcarahc)egnalfpukcabEMSArofelbatius(retemaidkcabnotaeS B
eziS – 8 ht retcarahc
1 1/2 EMSAniEMSAni2EMSAni3
1 1/2 ngiseddoofEMSAningiseddoofEMSAni3
04NDNE05NDNE08NDNE
ABC12DEF
hsiniftaeS 9– ht retcarahc
)EMSArofelbatius(hsinifdetarreS)EMSArofelbatius(hsinifhtoomS
04NPotpu;1BepyT1-2901NEothsinifdetarreS001NPot36NP;2BepyT1-2901NEothsinifdetarreS
)NErofelbatius(hsinifhtoomS
)2,1setoN()1etoN(
)3,2setoN()3,2setoN()3,2setoN(
DERST
edocesU 01– ht retcarahc F
lairetammgarhpaiD 11– ht retcarahc
ssL613ISIA™672CyolletsaH
™0002CyolletsaH526lenocnI
mulatnaTdetalpdlogssL613ISIA
gnitaockcits–itnahtiwssL613ISIAgnitaockcits–itnahtiw™672CyolletsaH
gnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA)tnemtaertnoisarbAitnAhtiwISIA(xelfaiD
)974ASMTSAot05723SSNU(ssxelpudrepuS
)4,2setoN()4,2setoN()4,2setoN()4,2setoN()4,2setoN()4,2setoN()4,2setoN()4,2setoN(
)2etoN()2etoN(
ECANECANECANECAN
ECANECANECANECANECANECAN
SHMLTNKYWFE
noitcetorpyrallipaC 21– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 31– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9
)33(01)04(21)74(41)35(61
ABCDEFGHJKLMNPQRSTUV
diulflliF 41– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)5,2setoN()5,2setoN(
)2etoN()2etoN()6etoN()6etoN()6etoN(
SNDHCWAB
noitacifitreC 51– ht retcarahc
enoN 1
2600T Pressure TransmittersModels S264 SS/S264_8
7
Note 1: Not available with EN size code D, E, F
Note 2: Not available with food design size code 1, 2
Note 3: Not available with ASME size code A, B, C
Note 4: Not available with serrated seat finish code D, R, S
Note 5: Suitable for oxygen service
Note 6: Suitable for food application
Note 7: Not available with flushing ring - hole and thread code 2, 3, 4, 5
Note 8: Not available with flushing ring - hole and thread code N
Note 9: Not available with flushing ring material code H
Note 10: Not available with AISI 316L flushing ring material code A
W462SNOITAMROFNIGNIREDROCISAB X X X
daerhtdnaeloh:gnirgnihsulF 61– ht retcarahc
enoNTPNni2/1-eloh1TPNni2/1-seloh2
TPNni4/1-eloh1TPNni4/1-seloh2
N2345
lairetamgnirgnihsulF 71– ht retcarahc
enoNssL613ISIA
672CyolletsaH
)7etoN()8etoN(
)8,4setoN(ECANECAN
NAH
teksagdnagulp:gnirgnihsulF 81– ht retcarahc
teksagon-gulpoNkcolrag-gulpoN
EFTP-gulpoNetihparg-gulpoN
teksagon-ssL613ISIAkcolrag-ssL613ISIA
EFTP-ssL613ISIAetihparg-ssL613ISIA
teksagon-672CyolletsaHkcolrag-672CyolletsaH
EFTP-672CyolletsaHetihparg-672CyolletsaH
)8etoN()8etoN()8etoN(
)9,8setoN()9,8setoN()9,8setoN()9,8setoN(
)01,8setoN()01,8setoN()01,8setoN()01,8setoN(
NABCDEFGHLMP
2600T Pressure TransmittersModels S264 SS/S264_8
8
S264C Model Chemical Tee Remote SealThe chemical tee remote seal is designed to connect to a Wedge Flow Element or to any process fitting with appropriate matingcondition.Chemical tee elements cannot be connected to a standard ASME or DIN pipe flange.
Maximum Working Pressure
2 MPa, 20 bar, 300 psi
Vacuum Service
Full vacuum subject to fill fluid limits.
Refer to table A.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
204°C (400°F) for use with Teflon anti-stick coating.
–100°C (–148°F) to 260°C (500°F) with PTFE gasket
–100°C (–148°F) to 340°C (645°F) with graphite gasket
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a seal ofspecific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4FOR TRANSMITTERS USING SAME REMOTE SEAL ON THE TWOSIDES
Capillary to instrument
DiaphragmSurface
eeTlacimehCeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
ni3 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
dia 127 (5)
dia
89 (3
.5)
8 Mounting Holesdia 8.73 (0.34)Equally Spaced
134 (5.3)
25 (1)12 (0.47)
dia 111 (4.38)
2600T Pressure TransmittersModels S264 SS/S264_8
9
BASIC ORDERING INFORMATION model S264C Chemical Tee Remote SealSelect one character or set of characters from each category and specify complete catalog number.
Note 1: Suitable for oxygen service
Note 2: Suitable for food application
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 C X X X P X X X X X
laeSetomeReeTlacimehC
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
egnalfgnitnuoM 7– ht retcarahclaeshtiwlargetnI P
eziS 8– ht retcarahc)gnitarrab02;dradnatsyrateirporp(ni3 G
edocesU 9– ht retcarahc
lairetammgarhpaiD 01– ht retcarahc
ssL613ISIA™672CyolletsaH
gnitaockcits–itnahtiwssL613ISIAgnitaockcits–itnahtiw™672CyolletsaH
gnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA
ECANECANECANECANECAN
SHKYW
noitcetorpyrallipaC 11– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 21– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9
)33(01
ABCDEFGHJKLMNPQRS
diulflliF 31– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)1etoN()1etoN(
)2etoN()2etoN()2etoN(
SNDHCWAB
teksaG 41– ht retcarahc
enoNrellifaciliShtiwEFTP
etihparG
167
2600T Pressure TransmittersModels S264 SS/S264_8
10
S264F Model Flanged Extended and Flush Diaphragm Remote SealThe extended and flush diaphragm remote seal is designed to connect to ASME or EN flanged pipe fitting. For liquid levelmeasurement installations the seal connects to an ASME or EN flanged tank nozzle (Schedule 40).The sealing is provided by a selectable smooth or serrated gasket seat surface finish.
Flanged Extended Diaphragm Seal Flanged Flush Diaphragm Seal
Capillary toInstrument
Capillary toInstrument
158 (6.22)
E
C A B
F G
D
158 (6.22)
B
F G
C
E
A D
50, 100 or 150mm(1.97, 3.94 or 5.91)
insertion length is available
gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS
)ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiDfo°N fo°N fo°N fo°N fo°Nseloh seloh seloh seloh seloh)aid(A )aid(A )aid(A )aid(A )aid(A
)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGGhsulf hsulf hsulf hsulf hsulf dednetxe dednetxe dednetxe dednetxe dednetxe
61NPNE05ND04NPNE05ND36NPNE05ND001NPNE05ND
61NPNE08ND04NPNE08ND36NPNE08ND001NPNE08ND61NPNE001ND04NPNE001ND
)63.2(06)63.2(06)63.2(06)63.2(06
)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98
)9.1(84)9.1(84
ANAN
)38.2(27)38.2(27
ANAN
)7.3(49)7.3(49
)20.4(201)20.4(201)20.4(201)20.4(201)34.5(831)34.5(831)34.5(831)34.5(831)22.6(851)83.6(261
)29.4(521)29.4(521)13.5(531)17.5(541
)3.6(061)3.6(061)7.6(071)80.7(081)80.7(081)84.7(091
)5.6(561)5.6(561)80.7(081)76.7(591)78.7(002)78.7(002)64.8(512)50.9(032)66.8(022)52.9(532
)17.0(81)17.0(81)68.0(22)20.1(62)17.0(81)17.0(81)68.0(22)20.1(62)17.0(81)68.0(22
)97.0(02)97.0(02)20.1(62
)1.1(82)97.0(02)49.0(42
)1.1(82)62.1(23)97.0(02)49.0(42
)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9
4444888888
gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS
)ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiDfo°N fo°N fo°N fo°N fo°Nseloh seloh seloh seloh seloh)aid(A )aid(A )aid(A )aid(A )aid(A
)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGGhsulf hsulf hsulf hsulf hsulf dednetxe dednetxe dednetxe dednetxe dednetxe
051LCEMSAni2003LCEMSAni2006LCEMSAni2009LCEMSAni2051LCEMSAni3003LCEMSAni3006LCEMSAni3009LCEMSAni3051LCEMSAni4003LCEMSAni4
)63.2(06)63.2(06)63.2(06)63.2(06
)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98
)9.1(84)9.1(84
ANAN
)38.2(27)38.2(27
ANAN
)7.3(49)7.3(49
)26.3(29)26.3(29)26.3(29)26.3(29
)5(721)5(721)5(721)5(721
)2.6(2.751)2.6(2.751
)57.4(56.021)5(721)5(721
)5.6(561)6(4.251
)26.6(51.861)26.6(51.861
)5.7(5.091)5.7(5.091
)88.7(2.002
)6(4.251)5.6(1.561)5.6(1.561)5.8(9.512)5.7(5.091
)52.8(55.902)52.8(55.902
)84.9(142)9(6.822)01(452
)97.0(02)97.0(02)97.0(02)20.1(62)97.0(02)68.0(22)68.0(22)20.1(62)97.0(02)68.0(22
)57.0(50.91)88.0(53.22
)1(4.52)5.1(1.83
)49.0(78.32)21.1(44.82)52.1(57.13
)05.1(1.83)49.0(42)62.1(23
)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9
4888488888
2600T Pressure TransmittersModels S264 SS/S264_8
11
Maximum Working Pressure
The pressure limit decreases with increasing temperature above120°C for carbon steel or 20°C for AISI 316 stainless steel,according to DIN 2401 standards.
The pressure limit decreases with increasing temperature above100°F (38°C), according to ASME B16.5 standards.
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Minimum pressure with tantalum diaphragm is 1kPa abs, 10mbar abs,0.15psia.
dednetxEdegnalFmgarhpaiDeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
05ND/ni2 Hni2.1,rabm3,aPk3.0 2O Hni4.0,rabm1,aPk1.0 2O Hn2.1,rabm3,aPk3.0 2O
08ND/ni3 Hni6.0,rabm5.1,aPk51.0 2O Hni23.0,rabm8.0,aPk80.0 2O Hni82.0,rabm7.0,aPk70.0 2O
001ND/ni4 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
hsulFdegnalFmgarhpaiDeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
05ND/ni2 Hni61.1,rabm9.2,aPk92.0 2O Hni82.0,rabm7.0,aPk70.0 2O Hni8.0,rabm2,aPk2.0 2O
08ND/ni3 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
001ND/ni4 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
Flanged Extended Diaphragm Remote Seal
Flanged Flush Diaphragm Remote Seal
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
260°C (500°F) for Tantalum diaphragm.
204°C (400°F) for use with Teflon anti-stick coating.
Gasket seat finish
Smooth (ASME or EN): 0.8µm (Ra)
Serrated (ASME): 3.2 to 6.3µm (Ra)
Serrated (EN 1092-1 Type B1; up to PN40): 3.2 to 12.5 µm (Ra)
Serrated (EN 1092-1 Type B2; PN63 - 100): 0.8 to 3.2 µm (Ra)
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a sealof specific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES
ssalC/gnitaR1-2901NEot
leetSnobraCC°021@
leetSsselniatS613ISIAC°02@
61NP rab61 rab61
04NP rab04 rab04
36NP rab36 rab36
001NP rab001 rab001
ssalC/gnitaR5.61BEMSAot
leetSnobraC)C°83(F°001@
leetSsselniatS613ISIA)C°83(F°001@
051ssalC isp582 isp572
003ssalC isp047 isp027
006ssalC isp0841 isp0441
009ssalC isp0222 isp0612
2600T Pressure TransmittersModels S264 SS/S264_8
12
BASIC ORDERING INFORMATION model S264F Flanged Remote Seal (flush and extended)Select one character or set of characters from each category and specify complete catalog number.
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 F X X X X X X X d'tnoC
)dednetxednahsulf(laesetomeRdegnalF
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
egnalfgnitnuoM 7– ht retcarahcgnitatoR R
eziS – 8 ht retcarahc
ni2ni2ni2ni2ni3
ngiseddoofni3ni3ni3ni3ni4ni4
05ND05ND05ND08ND08ND08ND08ND001ND001ND
051LCEMSA003LCEMSA006LCEMSA009LCEMSA051LCEMSA051LCEMSA003LCEMSA006LCEMSA009LCEMSA051LCEMSA003LCEMSA
04/61NPNE36NPNE
001NPNE61NPNE04NPNE36NPNE
001NPNE61NPNE04NPNE
ADGJB1EHKCFMPRNLQSTU
)laes(mroftaeS/egnalfgnitnuoM 9– ht retcarahc
leetsnobraCleetsnobraCleetsnobraCleetsnobraC
ss613ISIAss613ISIAss613ISIAss613ISIA
hsinifdetarres–)ecafdesiar(FRmroFhsinifhtooms–)ecafdesiar(FRmroF
hsinifdetarres–2B/1BepyT1-2901NEhsinifhtooms–2B/1BepyT1-2901NE
hsinifdetarres–)ecafdesiar(FRmroFhsinifhtooms–)ecafdesiar(FRmroF
hsinifdetarres–2B/1BepyT1-2901NEhsinifhtooms–2B/1BepyT1-2901NE
)3,1setoN()3,1setoN()3,2setoN()3,2setoN()3,1setoN(
)1etoN()3,2setoN()3,2setoN(
ABGPDELQ
lairetamdnahtgnelsnoisnetxE 01– ht retcarahc
)lairetammgarhpaidroftxenees(hsulF)ni2(mm05)ni2(mm05)ni4(mm001)ni4(mm001)ni6(mm051)ni6(mm051
ssL613ISIA™672yolletsaH
ssL613ISIA™672yolletsaH
ssL613ISIA™672yolletsaH
)4,3setoN()6,4,3setoN(
)4,3setoN()6,4,3setoN(
)4,3setoN()6,4,3setoN(
F123456
)laes(lairetammgarhpaiD 11– ht retcarahc
ssL613ISIA™672CyolletsaH
mulatnaTgnitaockcits–itnahtiwssL613ISIA
gnitaockcits–itnahtiw™672CyolletsaHgnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA
)5etoN()6etoN(
)7,6setoN()8,6,5setoN(
)8,6setoN()6,5setoN(
ECANECAN
ECANECANECAN
SHTKYW
noitcetorpyrallipaC 21– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
2600T Pressure TransmittersModels S264 SS/S264_8
13
Note 1: Not available with EN mounting flange code M, P, R, N, L, Q, S, T, U
Note 2: Not available with ASME mounting flange code A, D, G, J, B, E, H, K, C, F
Note 3: Not available with 3in ASME CL150 food design size code 1
Note 4: Not available with ASME CL 600 and CL 900 mounting flange rating code G, J, H, K and with EN PN63, PN100
mounting flange code P, R, Q, S
Note 5: Not available with Hastelloy C276 extension code 2, 4, 6
Note 6: Not available with serrated seat finish code A, G, D, L
Note 7: Not available with extension code 1, 2, 3, 4, 5, 6
Note 8: Not available with 2in, DN50, DN80, DN100 mounting flange code A, D, G, J, M, P, R, N, L, Q, S, T, U
Note 9: Suitable for oxygen service
Note 10: Suitable for food application
F462SNOITAMROFNIGNIREDROCISAB X X X
)teef(mhtgnelyrallipaC 31– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9
)33(01)04(21)74(41)35(61
ABCDEFGHJKLMNPQRSTUV
diulflliF 41– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)9,3setoN()9,3setoN(
)3etoN()3etoN(
)01etoN()01etoN()01etoN(
SNDHCWAB
noitacifitreC 51– ht retcarahc
enoN 1
2600T Pressure TransmittersModels S264 SS/S264_8
14
S264A - S264E Models Flanged Extended and Flush Diaphragm Remote SealThe extended and flush diaphragm remote seal is designed to connect to flanged pipe fitting, according to ASME (mod. S264A) orEN (mod. S264E) standards. For liquid level measurement installations the seal connects to an ASME or EN flanged tank nozzle(Schedule 40). The sealing is provided by a selectable smooth or serrated gasket seat surface finish.
Flanged Extended Diaphragm Seal Flanged Flush Diaphragm Seal
Capillary toInstrument
Capillary toInstrument
158 (6.22)
E
C A B
F G
D50, 100 or 150mm(1.97, 3.94 or 5.91)
insertion length is available
gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS
)ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiDfo°N fo°N fo°N fo°N fo°Nseloh seloh seloh seloh seloh)aid(A )aid(A )aid(A )aid(A )aid(A
)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGGdednetxe dednetxe dednetxe dednetxe dednetxemgarhpaid mgarhpaid mgarhpaid mgarhpaid mgarhpaid
hsulf hsulf hsulf hsulf hsulfmgarhpaid mgarhpaid mgarhpaid mgarhpaid mgarhpaid
gnirgnihsulf gnirgnihsulf gnirgnihsulf gnirgnihsulf gnirgnihsulfaidlanretni aidlanretni aidlanretni aidlanretni aidlanretni
051LCEMSAni2003LCEMSAni2006LCEMSAni2009LCEMSAni20051LCEMSAni2
051LCEMSAni3003LCEMSAni3006LCEMSAni3009LCEMSAni30051LCEMSAni3051LCEMSAni4003LCEMSAni4
)9.1(84)9.1(84
ANANAN
)38.2(27)38.2(27
ANANAN
)7.3(49)7.3(49
)63.2(06)63.2(06)63.2(06)63.2(06)63.2(06
)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98
)44.2(26)44.2(26)44.2(26)44.2(26)44.2(26)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29
)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29
)5(721)5(721)5(721)5(721)5(721
)2.6(2.751)2.6(2.751
)57.4(56.021)5(721)5(721)5.6(561)5.6(561)6(4.251
)26.6(51.861)26.6(51.861
)5.7(5.091)8(2.302)5.7(5.091)88.7(2.002
)6(4.251)5.6(1.561)5.6(1.561)5.8(9.512)5.8(9.512)5.7(5.091)52.8(55.902)52.8(55.902
)84.9(142)5.01(7.662
)9(6.822)01(452
)97.0(02)97.0(02)97.0(02)20.1(62)20.1(62)97.0(02)68.0(22)68.0(22)20.1(62
)52.1(57.13)97.0(02)68.0(22
)57.0(50.91)88.0(53.22
)1(4.52)5.1(1.83)5.1(1.83)49.0(78.32)21.1(44.82)52.1(57.13
)05.1(1.83)88.1(8.74
)49.0(42)62.1(23
)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9
488884888888
gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS
)ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiDfo°N fo°N fo°N fo°N fo°Nseloh seloh seloh seloh seloh)aid(A )aid(A )aid(A )aid(A )aid(A
)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGGdednetxe dednetxe dednetxe dednetxe dednetxemgarhpaid mgarhpaid mgarhpaid mgarhpaid mgarhpaid
hsulf hsulf hsulf hsulf hsulfmgarhpaid mgarhpaid mgarhpaid mgarhpaid mgarhpaid
gnirgnihsulf gnirgnihsulf gnirgnihsulf gnirgnihsulf gnirgnihsulfaidlanretni aidlanretni aidlanretni aidlanretni aidlanretni
61NPNE05ND04NPNE05ND36NPNE05ND001NPNE05ND
61NPNE08ND04NPNE08ND36NPNE08ND001NPNE08ND61NPNE001ND04NPNE001ND
)9.1(84)9.1(84
ANAN
)38.2(27)38.2(27
ANAN
)7.3(49)7.3(49
)63.2(06)63.2(06)63.2(06)63.2(06
)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98
)44.2(26)44.2(26)44.2(26)44.2(26)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29)26.3(29
)20.4(201)20.4(201)20.4(201)20.4(201)34.5(831)34.5(831)34.5(831)34.5(831)22.6(851)83.6(261
)29.4(521)29.4(521)13.5(531)17.5(541)3.6(061)3.6(061)7.6(071)80.7(081)80.7(081)84.7(091
)5.6(561)5.6(561)80.7(081)76.7(591)78.7(002)78.7(002)64.8(512)50.9(032)66.8(022)52.9(532
)17.0(81)17.0(81)68.0(22)20.1(62)17.0(81)17.0(81)68.0(22)20.1(62)17.0(81)68.0(22
)97.0(02)97.0(02)20.1(62)1.1(82)97.0(02)49.0(42)1.1(82)62.1(23)97.0(02)49.0(42
)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9
4444888888
25 (0.98) for 1/4 NPT
33 (1.30) for 1/2 NPTflushing thread(s)
Flushing ring(OPTION)
158 (6.22)
B
F G
C
E
A D
2600T Pressure TransmittersModels S264 SS/S264_8
15
Maximum Working Pressure
The pressure limit decreases with increasing temperature above120°C for carbon steel or 20°C for AISI 316 stainless steel,according to DIN 2401 standards.
The pressure limit decreases with increasing temperature above100°F (38°C), according to ASME B16.5 standards.
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Minimum pressure with tantalum diaphragm is 1kPa abs,10mbar abs, 0.15psia.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
260°C (500°F) for Tantalum diaphragm.
204°C (400°F) for use with Teflon anti-stick coating.
320°C (608°F) for AISI gold plated diaphragm.
dednetxEdegnalFmgarhpaiDeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
05ND/ni2 Hni2.1,rabm3,aPk3.0 2O Hni4.0,rabm1,aPk1.0 2O Hn2.1,rabm3,aPk3.0 2O
08ND/ni3 Hni6.0,rabm5.1,aPk51.0 2O Hni23.0,rabm8.0,aPk80.0 2O Hni82.0,rabm7.0,aPk70.0 2O
001ND/ni4 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
hsulFdegnalFmgarhpaiDeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
05ND/ni2 Hni61.1,rabm9.2,aPk92.0 2O Hni82.0,rabm7.0,aPk70.0 2O Hni8.0,rabm2,aPk2.0 2O
08ND/ni3 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
001ND/ni4 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
Flanged Extended Diaphragm Remote Seal
Flanged Flush Diaphragm Remote Seal
Gasket seat finish
Smooth (ASME or EN): 0.8µm (Ra)
Serrated (ASME): 3.2 to 6.3µm (Ra)
Serrated (EN 1092-1 Type B1; up to PN40): 3.2 to 12.5 µm (Ra)
Serrated (EN 1092-1 Type B2; PN63 - 100): 0.8 to 3.2 µm (Ra)
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a sealof specific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES
ssalC/gnitaR1-2901NEot
leetSnobraCC°021@
leetSsselniatS613ISIAC°02@
61NP rab61 rab61
04NP rab04 rab04
36NP rab36 rab36
001NP rab001 rab001
ssalC/gnitaR5.61BEMSAot
leetSnobraC)C°83(F°001@
leetSsselniatS613ISIA)C°83(F°001@
051ssalC isp582 isp572
003ssalC isp047 isp027
006ssalC isp0841 isp0441
009ssalC isp0222 isp0612
0051ssalC isp5073 isp0063
Limits for gaskets of flushing rings
lairetaM erusserP).xam(
erutarepmeT).nim().xam(
timilTxP
kcolraG,rab96,aPM9.6
isp0001C°402
)F°004(C°37–
)F°001–(000052
)ispxF°(
etihparG,rab52,aPM5.2
isp263C°083
)F°617(C°001–
)F°841–(
EFTP,rab06,aPM6
isp078C°052
)F°284(C°001–
)F°841–(
2600T Pressure TransmittersModels S264 SS/S264_8
16
BASIC ORDERING INFORMATION model S264A Flanged Remote Seal (flush and extended)Select one character or set of characters from each category and specify complete catalog number.
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 A X X X X X X X X X X d'tnoC
5.61BEMSAot)dednetxednahsulf(laesetomeRdegnalF
–noitcennocfoedisrettimsnarT 6 ht retcarahc
edishgiHediswoL
HL
egnalfgnitnuoM 7– ht retcarahc
gnitatoR R
eziS – 8 ht retcarahc
ni2ni3ni4
CDE
gnitaR – 9 ht retcarahc
051LCEMSA003LCEMSA006LCEMSA009LCEMSA
0051LCEMSA
)ezisni4htiwelbaliavatoN()ezisni4htiwelbaliavatoN()ezisni4htiwelbaliavatoN(
)1etoN()1etoN()1etoN(
12345
lairetamegnalfgnitnuoM 01– ht retcarahc
leetsnobraCss613ISIA
AB
lairetamdnahtgnelsnoisnetxE 11– ht retcarahc
)lairetammgarhpaidroftxenees(hsulF)ni2(mm05)ni2(mm05)ni4(mm001)ni4(mm001)ni6(mm051)ni6(mm051
ssL613ISIA™672yolletsaH
ssL613ISIA™672yolletsaH
ssL613ISIA™672yolletsaH
)2etoN()2etoN()2etoN()2etoN()2etoN()2etoN(
F123456
)laes(lairetammgarhpaiD 21– ht retcarahc
ssL613ISIA™672CyolletsaH
)smgarhpaiddednetxerofton(-™0002CyolletsaH)smgarhpaiddednetxerofton(-526lenocnI
)smgarhpaiddednetxerofton(-mulatnaT)smgarhpaiddednetxerofton(-detalpdlogssL613ISIA
gnitaockcits–itnahtiwssL613ISIAgnitaockcits–itnahtiw™672CyolletsaH
gnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA)tnemtaertnoisarbAitnAhtiwISIA(xelfaiD
)smgarhpaiddednetxerofton(-)974ASMTSAot05723SSNU(ssxelpudrepuS
)3etoN(
)4etoN()4etoN()4etoN()4etoN()3etoN(
)3etoN()3etoN()4etoN(
ECANECANECANECAN
ECANECANECAN
SHMLTNKYWFE
hsinifecafruslaeS 31– ht retcarahc
detarreShtoomS
)5,3setoN( 12
noitcetorpyrallipaC 41– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 51– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9
)33(01)04(21)74(41)35(61
ABCDEFGHJKLMNPQRSTUV
2600T Pressure TransmittersModels S264 SS/S264_8
17
Note 1: Not available with size code E
Note 2: Not available with mounting flange rating code 3, 4, 5
Note 3: Not available with extensions length and material code 2, 4, 6
Note 4: Not available with extensions length and material code 1, 2, 3, 4, 5, 6
Note 5: Not available with diaphragm material code M, L, T, N, K, Y, W and H when selected with extension length and material code F, 2, 4, 6
Note 6: Suitable for oxygen service
Note 7: Suitable for food application
Note 8: Not available with Flushing ring: hole and thread code 2, 3, 4, 5
Note 9: Not available with Flushing ring: hole and thread code N
Note 10: Not available with seal surface finish code 1 (serrated)
Note 11: Not available with flushing ring material code H
Note 12: Not available with AISI 316L flushing ring material code A
A462SNOITAMROFNIGNIREDROCISAB X X X X X
diulflliF 61– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)6etoN()6etoN(
)7etoN()7etoN()7etoN(
SNDHCWAB
noitacifitreC 71– ht retcarahc
enoN 1
daerhtdnaeloh:gnirgnihsulF 81– ht retcarahc
)SNOISREVDEDNETXEROFDETCELESEBOT(enoNTPNni2/1-eloh1TPNni2/1-seloh2
TPNni4/1-eloh1TPNni4/1-seloh2
)4etoN()4etoN()4etoN()4etoN(
N2345
lairetamgnirgnihsulF 91– ht retcarahc
enoNssL613ISIA
672CyolletsaH
)8etoN()9etoN(
)01,9setoN(ECANECAN
NAH
teksagdnagulp:gnirgnihsulF 02– ht retcarahc
teksagon-gulpoNkcolrag-gulpoN
EFTP-gulpoNetihparg-gulpoN
teksagon-ssL613ISIAkcolrag-ssL613ISIA
EFTP-ssL613ISIAetihparg-ssL613ISIA
teksagon-672CyolletsaHkcolrag-672CyolletsaH
EFTP-672CyolletsaHetihparg-672CyolletsaH
)9etoN()9etoN()9etoN(
)11,9setoN()11,9setoN()11,9setoN()11,9setoN()21,9setoN()21,9setoN()21,9setoN()21,9setoN(
NABCDEFGHLMP
2600T Pressure TransmittersModels S264 SS/S264_8
18
BASIC ORDERING INFORMATION model S264E Flanged Remote Seal (flush and extended)Select one character or set of characters from each category and specify complete catalog number.
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 E X X X X X X X X X X d'tnoC
1-2901NEot)dednetxednahsulf(laesetomeRdegnalF
–noitcennocfoedisrettimsnarT 6 ht retcarahc
edishgiHediswoL
HL
egnalfgnitnuoM 7– ht retcarahc
gnitatoR R
eziS – 8 ht retcarahc
05ND08ND
001ND
CDE
gnitaR – 9 ht retcarahc
61NP04NP36NP
001NP)ezis001NDroftoN()ezis001NDroftoN(
)1etoN()1etoN(
1234
lairetamegnalfgnitnuoM 01– ht retcarahc
leetsnobraCss613ISIA
AB
lairetamdnahtgnelsnoisnetxE 11– ht retcarahc
)lairetammgarhpaidroftxenees(hsulF)ni2(mm05)ni2(mm05)ni4(mm001)ni4(mm001)ni6(mm051)ni6(mm051
ssL613ISIA™672yolletsaH
ssL613ISIA™672yolletsaH
ssL613ISIA™672yolletsaH
)2etoN()2etoN()2etoN()2etoN()2etoN()2etoN(
F123456
)laes(lairetammgarhpaiD 21– ht retcarahc
ssL613ISIA™672CyolletsaH
)mgarhpaiddednetxerofton(-™0002CyolletsaH)mgarhpaiddednetxerofton(-526lenocnI
)mgarhpaiddednetxerofton(-mulatnaT)mgarhpaiddednetxerofton(-detalpdlogssL613ISIA
gnitaockcits-itnahtiwssL613ISIAgnitaockcits-itnahtiw™672CyolletsaH
gnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA)tnemtaertnoisarbAitnAhtiwISIA(xelfaiD
)mgarhpaiddednetxerofton(-)974ASMTSAot05723SSNU(ssxelpudrepuS
)3etoN(
)4etoN()4etoN(
)4etoN()3etoN(
)3etoN()3etoN()4etoN(
ECANECANECANECAN
ECANECANECAN
SHMLTNKYWFE
hsinifecafruslaeS 31– ht retcarahc
detarreShtoomS
)5,3setoN( 12
noitcetorpyrallipaC 41– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 51– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9
)33(01)04(21)74(41)35(61
ABCDEFGHJKLMNPQRSTUV
2600T Pressure TransmittersModels S264 SS/S264_8
19
Note 1: Not available with size code E
Note 2: Not available with mounting flange rating code 3, 4
Note 3: Not available with extensions length and material code 2, 4, 6
Note 4: Not available with extensions length and material code 1, 2, 3, 4, 5, 6
Note 5: Not available with diaphragm material code M, L, T, N, K, Y, W and H when selected with extension length and material code F, 2, 4, 6
Note 6: Suitable for oxygen service
Note 7: Suitable for food application
Note 8: Not available with Flushing ring: hole and thread code 2, 3, 4, 5
Note 9: Not available with Flushing ring: hole and thread code N
Note 10: Not available with seat surface finish code 1 (serrated)
Note 11: Not available with flushing ring material code H
Note 12: Not available with AISI 316L flushing ring material code A
E462SNOITAMROFNIGNIREDROCISAB X X X X X
diulflliF 61– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)6etoN()6etoN(
)7etoN()7etoN()7etoN(
SNDHCWAB
noitacifitreC 71– ht retcarahc
enoN 1
daerhtdnaeloh:gnirgnihsulF 81– ht retcarahc
)SNOISREVDEDNETXEROFDETCELESEBOT(enoNTPNni2/1-eloh1TPNni2/1-seloh2
TPNni4/1-eloh1TPNni4/1-seloh2
)4etoN()4etoN()4etoN()4etoN(
N2345
lairetamgnirgnihsulF 91– ht retcarahc
enoNssL613ISIA
672CyolletsaH
)8etoN()9etoN(
)01,9setoN(ECANECAN
NAH
teksagdnagulp:gnirgnihsulF 02– ht retcarahc
teksagon-gulpoNkcolrag-gulpoN
EFTP-gulpoNetihparg-gulpoN
teksagon-ssL613ISIAkcolrag-ssL613ISIA
EFTP-ssL613ISIAetihparg-ssL613ISIA
teksagon-672CyolletsaHkcolrag-672CyolletsaH
EFTP-672CyolletsaHetihparg-672CyolletsaH
)9etoN()9etoN()9etoN(
)11,9setoN()11,9setoN()11,9setoN()11,9setoN()21,9setoN()21,9setoN()21,9setoN()21,9setoN(
NABCDEFGHLMP
2600T Pressure TransmittersModels S264 SS/S264_8
20
S264G Model Flanged Flush Diaphragm Remote Seal to JISThis model identifies a diaphragm remote seal designed to connect to flanged pipe fitting, according to JIS standards.For liquid level measurement installations, the seal connects to an JIS flanged tank nozzle. The sealing is provided by a selectablesmooth or serrated gasket seat surface finish.
Capillary toInstrument
158 (6.22)
B
F G
C
E
A D
gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS
)ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiDfo°N fo°N fo°N fo°N fo°Nseloh seloh seloh seloh seloh)aid(A )aid(A )aid(A )aid(A )aid(A
hsulf hsulf hsulf hsulf hsulfmgarhpaid mgarhpaid mgarhpaid mgarhpaid mgarhpaid
)aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGG
K01ssalC05AK02ssalC05AK04ssalC05AK01ssalC08AK02ssalC08AK04ssalC08AK01ssalC001AK02ssalC001A
)63.2(06)63.2(06)63.2(06
)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98
)87.3(69)87.3(69
)11.4(3.401)69.4(621
)2.5(231)94.5(4.931
)49.5(151)3.6(061
)27.4(021)27.4(021)21.5(031)19.5(051
)3.6(061)96.6(071)98.6(571)82.7(581
)1.6(551)1.6(551)5.6(561)82.7(581)78.7(002)72.8(012)72.8(012)68.8(522
)95.0(51)57.0(91)57.0(91)95.0(51)19.0(32)19.0(32)57.0(91)19.0(32
)36.0(61)17.0(81)20.1(62)17.0(81)78.0(22)62.1(23)17.0(81)49.0(42
)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9)73.0(5.9
44888888
2600T Pressure TransmittersModels S264 SS/S264_8
21
Maximum Working Pressure
The pressure limit decreases with increasing temperature above120°C according to JIS B 2220 standards.
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Minimum pressure with tantalum diaphragm is 1kPa abs,10mbar abs, 0.15psia.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
260°C (500°F) for Tantalum diaphragm.
204°C (400°F) for use with Teflon anti-stick coating.
320°C (608°F) for AISI gold plated diaphragm.
Flanged Flush Diaphragm Remote Seal
Gasket seat finish
Smooth : 0.8µm (Ra)
Serrated : 3.2 to 6.3µm (Ra)
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a sealof specific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES
ssalC/gnitaR0222BSIJot
leetSnobraCC°021@
leetSsselniatS613ISIAC°021@
K01 rab41 rab41
K02 rab63 rab63
K04 rab86 rab86
hsulFdegnalFmgarhpaiDeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
05A Hni61.1,rabm9.2,aPk92.0 2O Hni82.0,rabm7.0,aPk70.0 2O Hni8.0,rabm2,aPk2.0 2O
08A Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
001A Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
2600T Pressure TransmittersModels S264 SS/S264_8
22
BASIC ORDERING INFORMATION model S264G Flanged Flush Remote Seal to JISSelect one character or set of characters from each category and specify complete catalog number.
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 G X X X X X X X X X X d'tnoC
SIJotlaesetomeRhsulFdegnalF
–noitcennocfoedisrettimsnarT 6 ht retcarahc
edishgiHediswoL
HL
egnalfgnitnuoM 7– ht retcarahc
gnitatoR R
eziS – 8 ht retcarahc
05A08A001A
BCD
gnitaR – 9 ht retcarahc
K01K02K04 )1etoN(
246
lairetamegnalfgnitnuoM 01– ht retcarahc
leetsnobraCss613ISIA
AB
lairetamdnahtgnelsnoisnetxE 11– ht retcarahc
)lairetammgarhpaidroftxenees(hsulF F
)laes(lairetammgarhpaiD 21– ht retcarahc
ssL613ISIA™672CyolletsaH™0002CyolletsaH
526lenocnImulatnaT
detalpdlogssL613ISIAgnitaockcits–itnahtiwssL613ISIA
gnitaockcits–itnahtiw™672CyolletsaHgnitaockcits-itnadnanoisorroc-itnahtiwssL613ISIA
)974ASMTSAot05723SSNU(ssxelpudrepuS
ECANECANECANECAN
ECANECANECANECANECAN
SHMLTNKYWE
hsinifecafruslaeS 31– ht retcarahc
detarreShtoomS
)2etoN( 12
noitcetorpyrallipaC 41– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 51– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9)33(01)04(21)74(41)35(61
ABCDEFGHJKLMNPQRSTUV
2600T Pressure TransmittersModels S264 SS/S264_8
23
Note 1: Not available with A100 size code D
Note 2: Not available with diaphragm material code H, M, L, T, N, K, Y, W
Note 3: Suitable for oxygen service
Note 4: Suitable for food application
G462SNOITAMROFNIGNIREDROCISAB X X X X X
diulflliF 61– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)3etoN()3etoN(
)4etoN()4etoN()4etoN(
SNDHCWAB
noitacifitreC 71– ht retcarahc
enoN 1
daerhtdnaeloh:gnirgnihsulF 81– ht retcarahc
enoN N
lairetamgnirgnihsulF 91– ht retcarahc
enoN N
teksagdnagulp:gnirgnihsulF 02– ht retcarahc
teksagon-gulpoN N
2600T Pressure TransmittersModels S264 SS/S264_8
24
This flush diaphragm remote seal is designed to connect to ASME flanged pipe fitting, the sealing is provided by a metal ring in theprovided groove. For liquid level measurement installations the seal connects to an ASME flanged tank nozzle (Schedule 40).
Capillary toInstrument
158 (6.22)
B
F G
C
E
A DH
gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS gnitaR/eziS
)ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD )ni(mmsnoisnemiD
RRRRRfo°N fo°N fo°N fo°N fo°Nseloh seloh seloh seloh seloh
)aid(A )aid(A )aid(A )aid(A )aid(A )aid(B )aid(B )aid(B )aid(B )aid(B )aid(C )aid(C )aid(C )aid(C )aid(C )aid(D )aid(D )aid(D )aid(D )aid(D )aid(E )aid(E )aid(E )aid(E )aid(E FFFFF GGGGG )aid(H )aid(H )aid(H )aid(H )aid(H
051LCEMSAni2/1-1003LCEMSAni2/1-1006LCEMSAni2/1-1
0051/009LCEMSAni2/1-10052LCEMSAni2/1-1
051LCEMSAni2003LCEMSAni2006LCEMSAni2
0051/009LCEMSAni20052LCEMSAni2
051LCEMSAni3003LCEMSAni3006LCEMSAni3009LCEMSAni30051LCEMSAni30052LCEMSAni3
)98.1(84)98.1(84)98.1(84)98.1(84)98.1(84)63.2(06)63.2(06)63.2(06)63.2(06)63.2(06
)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98)5.3(98
)72.3(38)45.3(09)45.3(09)26.3(29)94.4(411)20.4(201)52.4(801)52.4(801)88.4(421)42.5(331)42.5(331)57.5(641)57.5(641)01.6(551)16.6(861)16.6(861
)88.3(6.89)5.4(3.411)5.4(3.411
)88.4(421)57.5(1.641)57.4(56.021
)5(721)5(721
)5.6(561)57.6(5.171
)6(4.251)26.6(51.861)26.6(51.861
)5.7(5.091)8(2.302)9(6.822
)5(721)21.6(5.551)21.6(5.551
)7(8.771)8(2.302)6(4.251
)5.6(1.561)5.6(1.561)5.8(9.512
)52.9(532)5.7(5.091
)52.8(55.902)52.8(55.902
)5.9(3.142)5.01(7.662
)21(8.403
)26.0(57.51)88.0(53.22)88.0(53.22)21.1(54.82)52.1(57.13)57.0(50.91)57.0(50.91)57.0(50.91
)1(4.52)21.1(54.82)57.0(50.91)88.0(53.22)88.0(53.22
)1(4.52)52.1(57.13)83.1(50.53
)96.0(5.71)18.0(6.02)88.0(4.22)52.1(8.13)57.1(5.44)57.0(50.91)88.0(53.22
)1(4.52)5.1(1.83
)2(8.05)49.0(78.32)21.1(44.82)52.1(57.13
)05.1(1.83)88.1(8.74)26.2(5.66
)86.0(3.71)86.0(3.71)86.0(3.71)28.0(8.02)28.0(8.02)86.0(3.71)86.0(3.71)86.0(3.71)28.0(8.02)28.0(8.02)86.0(3.71)86.0(3.71)86.0(3.71)28.0(8.02)28.0(8.02)28.0(8.02
)65.2(1.56)96.2(3.86)96.2(3.86)96.2(3.86)52.3(6.28)52.3(6.28)52.3(6.28)52.3(6.28)57.3(3.59
)4(6.101)5.4(3.411)78.4(8.321)78.4(8.321)78.4(8.321)73.5(5.631
)5(721
91R02R02R02R32R22R32R32R42R62R92R13R13R13R53R23R
4444448888488888
S264R Model Flanged Flush Diaphragm Remote Seal - Ring Joint
2600T Pressure TransmittersModels S264 SS/S264_8
25
Maximum Working Pressure
The pressure limit decreases with increasing temperature above100°F (38°C), according to ASME B16.5 standards.
Flanged Flush Diaphragm Remote Seal - Ring Joint
ssalC/gnitaR5.61BEMSAot
leetSnobraC)C°83(F°001@
leetSsselniatS613ISIA)C°83(F°001@
051ssalC isp582 isp572
003ssalC isp047 isp027
006ssalC isp0841 isp0441
009ssalC isp0222 isp0612
0051ssalC isp5073 isp0063
0052ssalC isp0716 isp0006
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a sealof specific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES
hsulFdegnalFmgarhpaiD
eziSlaeStnioJgniRrorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
1 1/2 ni Hni5.3,rabm7.8,aPk78.0 2O Hni2.1,rabm3,aPk3.0 2O Hni6.3,rabm9,aPk9.0 2O
ni2 Hni61.1,rabm9.2,aPk92.0 2O Hni82.0,rabm7.0,aPk70.0 2O Hni8.0,rabm2,aPk2.0 2O
ni3 Hni63.0,rabm9.0,aPk90.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
2600T Pressure TransmittersModels S264 SS/S264_8
26
BASIC ORDERING INFORMATION model S264R Flanged Remote Seal - Ring JointSelect one character or set of characters from each category and specify complete catalog number.
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 R X X X X X X X X X X d'tnoC
5.61BEMSAottniojgniRlaesetomeRdegnalF
–noitcennocfoedisrettimsnarT 6 ht retcarahc
edishgiHediswoL
HL
egnalfgnitnuoM 7– ht retcarahc
gnitatoR R
eziS – 8 ht retcarahc
ni2/1-1ni2ni3
BCD
gnitaR – 9 ht retcarahc
051LCEMSA003LCEMSA006LCEMSA009LCEMSA
0051LCEMSA0052LCEMSA
123456
lairetamegnalfgnitnuoM 01– ht retcarahc
leetsnobraCss613ISIA
AB
lairetamdnahtgnelsnoisnetxE 11– ht retcarahc
)lairetammgarhpaidroftxenees(hsulF F
lairetammgarhpaiD 21– ht retcarahc
ssL613ISIA™672CyolletsaH
526lenocnI
ECANECANECAN
SHL
hsinifecafruslaeS 31– ht retcarahc
tniojgniR 3
noitcetorpyrallipaC 41– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 51– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9
)33(01)04(21)74(41)35(61
ABCDEFGHJKLMNPQRSTUV
2600T Pressure TransmittersModels S264 SS/S264_8
27
Note 1: Suitable for oxygen service
Note 2: Suitable for food application
R462SNOITAMROFNIGNIREDROCISAB X X X X X
diulflliF 61– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)1etoN()1etoN(
)2etoN()2etoN()2etoN(
SNDHCWAB
noitacifitreC 71– ht retcarahc
enoN 1
daerhtdnaeloh:gnirgnihsulF 81– ht retcarahc
dettiftoN N
lairetamgnirgnihsulF 91– ht retcarahc
enoN N
teksagdnagulp:gnirgnihsulF 02– ht retcarahc
enoN N
2600T Pressure TransmittersModels S264 SS/S264_8
28
S264T Model Off-line Threaded Connection Remote SealThe off-line threaded connection remote seals are designed to connect directly to a process pipe via the NPT connection in the lowerhousing . These elements are available with a flushing connection, on request, in the lower housing.
Maximum Working Pressure
16 MPa, 160 bar, 2320 psi @ 20°C (68°F)
The pressure limit decreases with increasing temperature above 20°C(68°F)
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Minimum pressure with tantalum diaphragm is 1kPa abs, 10mbar abs,0.15psia.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
260°C (500°F) for Tantalum diaphragm
320°C (608°F) for AISI gold plated diaphragm
–100°C (–148°F) to 260°C (500°F) with PTFE gasket
–20°C (-4°F) to 200°C (392°F) with Viton gasket
360°C (680°F) with Graphite gasket
Mounting flange
AISI 316 L ss, Hastelloy C
Gasket (flange to seal)
Viton, PTFE, Graphite
Bolts
AISI 316 ss bolts Class A4-80 and nuts Class A4-70 per EN ISO3506;Carbon steel bolts Class 8.8 per EN ISO 4014 and nuts Class 8 perEN ISO 898/2;Alloy steel bolts per ASTM-A-193-77a grade B7M and nuts perASTM A194/A 194 M-90 grade 2HM, in compliance with NACEMR0175 Class II.
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a seal ofspecific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES
Gasket
DiaphragmProcess
Connection
Lower Housing
1/4in NPT-fFlushing connection
(option)
dedaerhTeniL-ffOeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
2 1/2 ni Hni82.1,rabm2.3,aPk23.0 2O Hni27.0,rabm8.1,aPk81.0 2O Hni6.0,rabm5.1,aPk51.0 2O
Q
D
134
(5.3
) eziS)ni(mmsnoisnemiD
)aid(D Q
1/4 TPNni )3.4(2.901 )1.2(3.35
1/2 TPNni )3.4(2.901 )1.2(3.35
3/4 TPNni )3.4(2.901 )5.2(5.36
TPNni1 )3.4(2.901 )5.2(5.36
1 1/2 TPNni )3.4(2.901 )5.2(5.36
2600T Pressure TransmittersModels S264 SS/S264_8
29
BASIC ORDERING INFORMATION model S264T Off-Line Threaded Connection Remote Seal
Note 1: Suitable for oxygen service
Note 2: Suitable for food application
Note 3: Not available with Size code 4
Select one character or set of characters from each category and specify complete catalog number.LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 T X X X X X X X X X X
laesetomerdedaerhtenil-ffO
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
eziS 7– ht retcarahc1/4 f-TPNni1/2 f-TPNni3/4 f-TPNni
f-TPNni1-1 1/2 f-TPNni
12534
stloB – 8 ht retcarahc
ss613ISIAleetsnobraC
leetsyollA ECAN
123
lairetamegnalF 9– ht retcarahc
ssL613ISIA™672CyolletsaH
ECANECAN
12
lairetammgarhpaiD 01– ht retcarahc
ssL613ISIA™672CyolletsaH
™0002CyolletsaH526lenocnI
mulatnaTdetalpdlogssL613ISIA
ECANECANECANECAN
SHMLTN
noitcetorpyrallipaC 11– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 21– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9
ABCDEFGHJKLMNPQR
diulflliF 31– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)1etoN()1etoN(
)2etoN()2etoN()2etoN(
SNDHCWAB
snoitcennocgnihsulF 41– ht retcarahc
deriuqertoNdedivorP )3etoN(
1Q
teksaG 51– ht retcarahc
EFTP™notiV
etihparG
237
2600T Pressure TransmittersModels S264 SS/S264_8
30
The off-line flanged connection remote seals are designed toconnect directly to ASME or EN flanged tank nozzles.These elements are available with a flushing connection in thelower housing, selectable on request in the ordering code.
Maximum Working Pressure
Class 150 to ASME B16.5: 230psi @ 100°F (38°C)
Class 300 to ASME B16.5: 600psi @ 100°F (38°C)
PN16-40 to EN 1092-1: 34bar @ 20°C
The pressure limit decreases with increasing temperature above to thespecified values respectively for ASME B16.5 or EN 1092-1 std.
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Minimum pressure with tantalum diaphragm is 1kPa abs, 10mbar abs,0.15psia.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
260°C (500°F) for Tantalum diaphragm
320°C (608°F) for AISI gold plated diaphragm
–100°C (–148°F) to 260°C (500°F) with PTFE gasket
–20°C (-4°F) to 200°C (392°F) with Viton gasket
360°C (680°F) with Graphite gasket
Gasket seat finish (flange to process)
serrated (ASME): 3.2 to 6.3µm (Ra)
serrated (EN 1092-1 Type B1): 3.2 to 12.5µm (Ra)
Mounting flange
AISI 316 L ss, Hastelloy C
Gasket (flange to seal)
Viton, PTFE, Graphite
Bolts
bolts (seal/flange): AISI 316 ss Class A4-70 per EN ISO 3506;
studs with nuts (flange/process): AISI 3xx per ASTM-SA-193/194grade B8C or B8T
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a seal ofspecific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fluid characteristics table.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES.
1/4in NPT-fFlushing connections(2 opposite at 180°
as option)
GasketSeatfinish
degnalFeniL-ffOeziSlaeS
rorrelaeS rorrEyrallipaCm1rorrE)rosneS(metsyS
2 1/2 ni Hni82.1,rabm2.3,aPk23.0 2O Hni27.0,rabm8.1,aPk81.0 2O Hni6.0,rabm5.1,aPk51.0 2O
63.5
(2.5
)
dia 110 (4.33)
B
E
D
F
A
C
134
(5.3
)
S264M Model Off-line Flanged Connection Remote Seal
noitcennoC )ni(mmsnoisnemiD
eziS dradnatS )aid(A )aid(B)sduts4(C
)aid(D )aid(E FhtgneL daerhT
1/2 ni051LCEMSA )33.4(011 )83.2(5.06 )35.1(93 CNU31–ni2/1
)83.1(1.53 )26.0(8.51 )60.0(6.1003LCEMSA )33.4(011 )26.2(5.66 )35.1(93 CNU31–ni2/1
ni1051LCEMSA )33.4(011 )21.3(4.97 )35.1(93 CNU31–ni2/1
)2(8.05 )50.1(7.62 )60.0(6.1003LCEMSA )88.4(421 )5.3(9.88 )2(15 CNU11–ni8/5
1 1/2 ni051LCEMSA )5(721 )78.3(4.89 )35.1(93 CNU31–ni2/1
)78.2(37 )16.1(14 )60.0(6.1003LCEMSA )1.6(551 )5.4(3.411 )42.2(75 CNU01–ni4/3
52ND 04-61NPNE )25.4(511 )43.3(58 )56.1(24 21M )76.2(86 )21.1(5.82 )70.0(204ND 04-61NPNE )9.5(051 )33.4(011 )98.1(84 61M )64.3(88 )96.1(1.34 )21.0(3
2600T Pressure TransmittersModels S264 SS/S264_8
31
BASIC ORDERING INFORMATION model S264M Off-line Flanged Connection Remote SealSelect one character or set of characters from each category and specify complete catalog number.
Note 1: Not available with EN mounting flange code M, N
Note 2: Not available with ASME mounting flange code A, B, C, D, 6, 7
Note 3: Suitable for oxygen service
Note 4: Suitable for food application
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 M X X X X X X X X X X
laesetomerdegnalf-inimenil-ffO
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
egnalfgnitnuoM 7– ht retcarahclaeshtiwlargetnI P
gnitaregnalfgnitnuoM/eziS – 8 ht retcarahc
1/2 ni1/2 ni
ni1ni1
1 1/2 ni1 1/2 ni
52ND04ND
051LCEMSA003LCEMSA051LCEMSA003LCEMSA051LCEMSA003LCEMSA
04/61NPNE04/61NPNE
67ACBDMN
)laes(mroftaeS/egnalfgnitnuoM 9– ht retcarahc
ssL613ISIAssL613ISIA
™672CyolletsaH™672CyolletsaH
hsinifdetarres–)ecafdesiar(FRmroFhsinifdetarres–1BepyT1-2901NE
hsinifdetarres–)ecafdesiar(FRmroFhsinifdetarres–1BepyT1-2901NE
)1etoN()2etoN()1etoN()2etoN(
ECANECANECANECAN
DLUV
)laes(lairetammgarhpaiD 01– ht retcarahc
ssL613ISIA™672CyolletsaH
™0002CyolletsaH526lenocnI
mulatnaTdetalpdlogssL613ISIA
ECANECANECANECAN
SHMLTN
noitcetorpyrallipaC 11– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 21– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
)21(5.3)31(4
)51(5.4)71(5
)81(5.5)02(6
)22(5.6)32(7
)52(5.7)72(8)03(9
ABCDEFGHJKLMNPQR
diulflliF 31– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)3etoN()3etoN(
)4etoN()4etoN()4etoN(
SNDHCWAB
snoitcennocgnihsulF 41– ht retcarahc
deriuqertoNdedivorP
1Q
teksaG 51– ht retcarahc
EFTP™notiV
etihparG
237
2600T Pressure TransmittersModels S264 SS/S264_8
32
S264U Model Union Connection Remote Seal (To be used only for gauge pressure)The union connection remote seal are used exclusively for pressure measurement with gauge pressure transmitter.The seal is available with an optional weld bushing, or with an optional chemical tee flange.The remote seal with a weld bushing,includes a bushing which provides the mating surface for the seal element. The union connection seal with a chemical tee flange, isdesigned to connect to any process fitting which accepts a chemical tee seal element (refer to Chemical Tee Seal for more information).The union seal connects to the chemical tee flange which serves as an adaptor to permit connection of the union seal to a chemical teetype fitting.
Maximum Working Pressure
Union Connection: 10.3 MPa, 103 bar, 1500 psi
With Chemical Tee Flange : 2 MPa, 20 bar, 300 psi
Vacuum Service
Full vacuum subject to fill fluid limits.
Refer to table A.
Process Temperature Limits
Same as fill fluid limits.
Refer to table A.
–50°C (–58°F) to 204°C (400°F) with silicone rubber gasket
–100°C (–148°F) to 260°C (500°F) with PTFE gasket
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a seal ofspecific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
Capillary toinstrument
DiaphragmSurface
WeldingBushing
Capillary toInstrument
Capillary toinstrument
UnionConnection Seal
UnionConnection
DiaphragmSurface
Chemical TeeFlange
O-Ring
noitcennoCnoinUeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
1 1/2 ni Hni5.3,rabm7.8,aPk78.0 2O Hni2.1,rabm3,aPk3.0 2O Hni6.3,rabm9,aPk9.0 2O
Union Connection Seal without weld bushing
Union Connection Sealwith chemical tee flange
Union Connection Sealwith weld bushing
120 (4.7) 25 (1)
dia
42 (1
.65)
dia
89 (3
.5)
UnionConnection
57 (2.25)
120 (4.7) 25 (1)
12 (0.47)
dia
96 (3
.78)
dia
42 (1
.65)
dia
127
(5)
8 Mounting Holes dia 8.7 (0.34)Equally Spaced on 111.125 (4.37)
Bolt Circle
dia
41 (1
.61)
dia
42 (1
.65)
dia
51 (2
) 29 (1.14)
134 (5.3)
16 (0.63)
9 (0.35)14 (0.55)
45°
5 (0.19)
5 (0.19)
4 (0.16)
dia
42 (1
.65)
2 (0.08)
54 (2.12) - 16N210 (0.39) Full Thread
2600T Pressure TransmittersModels S264 SS/S264_8
33
BASIC ORDERING INFORMATION model S264U Union Connection Remote SealSelect one character or set of characters from each category and specify complete catalog number.
Note 1: Suitable for oxygen service
Note 2: Suitable for food application
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 U X X X X X X X X
)RETTIMSNARTHCAEROFYLNOENOEBTSUM(laesetomernoitcennocnoinU
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
eziS 7– ht retcarahc1 1/2 ni L
)laes(lairetammgarhpaiD 8– ht retcarahc
ssL613ISIA™672CyolletsaH
ECANECAN
SH
noitcetorpyrallipaC 9– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 01– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2
)01(3
ABCDE
diulflliF 11– ht retcarahc
lioenociliSnedlaG-diulftrenI
nobracolaH-diulftrenIerutarepmethgihroflioenocilIS
erutarepmetwolrofremylopenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)1etoN()1etoN(
)2etoN()2etoN()2etoN(
SNDHCWAB
snoitpO 21– ht retcarahc
enoNgnihsubdlewss613ISIA
egnalfeetlacimehC
134
teksaG 31– ht retcarahc
rebburenociliSEFTP
58
2600T Pressure TransmittersModels S264 SS/S264_8
34
S264S Food and Sanitary Remote SealsThe Union Nut and Triclamp remote seals are designed for connection by Union Nut according to DIN 11851 - F50 or F80 and 2 in,3 in, 4 in Triclamp sanitary fittings. A variety of gaskets and clamp rings for the seals are available.
pmalcirT
ni2 ni3 ni4
)aid(A )2.2(3.65 )62.3(38 )43.4(3.011
)aid(B )5.2(46 )85.3(19 86.4(911
Union Nut Seal (to DIN 11851)
Triclamp Seal
The Cherry Burrell remote seals are designed for connection to 2in, 3in or 4in Cherry Burrell I-Line sanitary fittings.A 4in V-band clamp is optionally available for the 4in variant.
tuNnoinU
05F 08F
)aid(A )86.2(86 )39.3(001
)DR(B )70.3(87 )33.4(011
C )36.0(61 )47.0(91
A
B
C13
4 (5
.3)
27 (1
.06)A
B
20
(0.7
9)
2.8
5 (0
.11)
134
(5.3
)
E
FH
G
B
A
C
D
eziS)ni(mmSNOISNEMID
)aid(A )aid(B )aid(C )aid(D E F G H
ni2 )46.2(76 )2.2(65 )56.1(24 )42.2(75 )31.0(2.3 )62.0(5.6 )94.0(5.21 )21.0(3
ni3 )78.3(4.89 )91.3(18 )58.2(24.27 )3.3(8.38 )90.0(4.2 )13.0(9.7 )95.0(51 )21.0(3
ni4 )88.4(421 )83.4(52.111 )58.2(24.27 )3.4(3.901 90.0(4.2 )13.0(9.7 )95.0(51 )21.0(3
Note: seal model not3-A authorized
2600T Pressure TransmittersModels S264 SS/S264_8
35
The sanitary remote seal with flush diaphragm is designed to connect to a 4in sanitary tank spud. The tank spud and process gasketare available as options with the seal suitable V-band clamp is also available on request.NOTE: The tank spud required for connection of this seal element must be welded to the process vessel prior to connecting the seal,following a recommended welding and pressure testing procedure.
The sanitary remote seal with extended diaphragm is designed to connect to a 4in sanitary tank spud. The tank spud and processgasket are available with the seal.NOTE: The tank spud required for connection of this seal element must be welded to the process vessel prior to connecting the seal,following a recommended welding and pressure testing procedure.
eziS)ni(mmsnoisnemiD
A
ni2 )1.2(3.35
ni4 )1.4(1.401
ni6 )1.6(9.451
dia 72 (2.83)
dia 110 (4.33)
dia 152.4 (6)
19.3
(0.7
5)
18.5
(0.7
2)
8 (0
.31)
for
thin
wal
l
13 (0
.51)
for
thic
k w
all
dia 119 (4.68)
dia 85.5 (3.36)dia 36 (1.41)
dia 72 (2.83)dia 100 (3.93)dia 152 (5.98)
A10
(0.3
9)
5.6
(0.2
2)
dia 132.6 (5.22)
2600T Pressure TransmittersModels S264 SS/S264_8
36
The sanitary aseptic remote seal is designed to connect to a 4in sanitary fitting: either an aseptic tank spud or a 4in Cherry Burrellaseptic ferrule. The tank spud, gaskets and V-band clamp are available option with the seal element.NOTE: The tank spud or ferrule required for connection of this seal element must be welded to the process vessel prior toconnecting the element, following recommended welding and pressure testing procedure. Weld the Cherry Burrell ferrule to theprocess vessel in accordance with manufacturers recommandations.
4in Aseptic Flanged Connection
4in Cherry Burrell Aseptic
Maximum Working Pressure @ 20°C (68°F)
2 in Triclamp : 3.8 MPa, 38 bar, 550 psi
3 in Triclamp : 2.4 MPa, 24 bar, 350 psi
4 in Triclamp : 1.7 MPa, 17 bar, 250 psi
F50/F80 Union nut : 2.5 MPa, 25 bar, 360 psi
Cherry Burrell: 1.9MPa, 19bar, 275psi
4in Sanitary flush or extended or aseptic: 1.9MPa, 19bar, 275psi
4in V-band clamp option: 1MPa, 10bar, 145psi
4in schedule 5 V-band clamp option: 0.7MPa, 7bar, 100psi @ 21°C.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
Process Gasket Temperature Limits
Ethylene Propylene EPDM 3-A 18-03 Class II:–40 to 121°C (–40 to 250°F)
Ethylene Propylene: –40 to149°C (–40 to 300°F)
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a seal ofspecific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES
,llerruByrrehC,pmalcirT,tuNnoinUeziSlaeScitpesAdnayratinaS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
05F/ni2 Hn8.2,rabm7,aPk7.0 2O Hni7.1,rabm2.4,aPk24.0 2O Hni6.5,rabm41,aPk4.1 2O
08F/ni3 Hni42.0,rabm6.0,aPk60.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
ni4 Hni42.0,rabm6.0,aPk60.0 2O Hni21.0,rabm3.0,aPk30.0 2O Hni21.0,rabm3.0,aPk30.0 2O
2 holes 1/8in–27NPT(180° symmetrical for steam connection)
dia 119 (4.68)
dia 105 (4.13)
dia 85.5 (3.36)
dia 79.6 (3.13)dia 62 (2.44)
4.2
(0.1
6)
19.3
(0.7
5)
11.2
(0.7
5)
dia 72.4 (2.85)
dia 82.6 (3.25)
dia 111.25 (4.37)
dia 124 (4.88)
2.4
(0.0
9)
7.9
(0.3
1)3
(0.1
1)
15 (0
.59)
2600T Pressure TransmittersModels S264 SS/S264_8
37
BASIC ORDERING INFORMATION model S264S Food and Sanitary Remote SealsSelect one character or set of characters from each category and specify complete catalog number.
Note 1: Union nut DIN 11851 (F50 and F80) are not 3-A authorized models
Note 2: Suitable for food application
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 S X X X X X X X X
slaesetomeryratinaSdnadooF
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
noitcennocgnitnuoM 7– ht retcarahc05F–15811NIDtunnoinU08F–15811NIDtunnoinU
pmalcirTni2pmalcirTni3pmalcirTni4
llerruByrrehCni2llerruByrrehCni3llerruByrrehCni4
mgarhpaidhsulfyratinaSni4mgarhpaid)ni2(dednetxeyratinaSni4mgarhpaid)ni4(dednetxeyratinaSni4mgarhpaid)ni6(dednetxeyratinaSni4
citpesallerruByrrehCni4noitcennocdegnalfcitpesani4
)1etoN()1etoN(
ABFGHLMNPQRSWJ
lairetammgarhpaidlaeS – 8 ht retcarahc
ssL613ISIA S
noitcetorpyrallipaC 9– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 01– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2
)01(3)21(5.3
)31(4)51(5.4
)71(5)81(5.5
)02(6)22(5.6
)32(7)52(5.7
)72(8)03(9
)33(01
ABCDEFGHJKLMNPQRS
diulflliF 11– ht retcarahc
lioenociliS)devorppaADF(liolareniM
)devorppaADF(lioelbategeV)devorppaADF(retaw-nirecylG
)2etoN()2etoN()2etoN(
SWAB
sgnittiF/pmalC 21– ht retcarahc
enoN)pmalcirTni2rof(pmalCdnab-Vni2)pmalcirTni3rof(pmalCdnab-Vni3
)degnalfcitpesani4dnahsulfyratinaSni4,llerruByrrehCni4,pmalcirTni4rof(pmalCdnab-Vni4)laeshsulfyratinaSni4rof(pmalCdnab-Vni4dna)81.0(mm7.4otpullawknat,dupsknaTni4)laeshsulfyratinaSni4rof(pmalCdnab-Vni4dna)73.0(mm5.9otpullawknat,dupsknaTni4
)laesdednetxeyratinaSni4rof(pmalcdnab-V5eludehcsni4)laesni2dednetxeyratinaSni4rof(pmalcdnab-V5eludehcsni4dnanoisnetxeni2rofdupsknaT)laesni4dednetxeyratinaSni4rof(pmalcdnab-V5eludehcsni4dnanoisnetxeni4rofdupsknaT)laesni6dednetxeyratinaSni4rof(pmalcdnab-V5eludehcsni4dnanoisnetxeni6rofdupsknaT
)laesdegnalfcitpesani4rof(dupsknatcitpesA
1ABCDEFGHJP
teksaG 31– ht retcarahc
enoN)IIssalC30-81A-3MDPE(-)laesdednetxeyratinaSni4rof(001NDteksagenelyporpenelyhtE
)laestunnoinU05Frof(05NDteksagenelyporpenelyhtE)laestunnoinU08Frof(08NDteksagenelyporpenelyhtE
)IIssalC30-81A-3MDPE(-)laesdegnalfcitpesadnahsulfyratinasni4rof(teksagenelyporpenelyhtE
1ACDG
2600T Pressure TransmittersModels S264 SS/S264_8
38
S264P Remote seal(s) for Urea Service
Maximum Working Pressure @ 20°C (68°F)
3in, ASME 600 flange:
- 8 MPa, 80 bar, 1160 psi
2in ASME 2500 threaded flange:
- 32 MPa, 320 bar, 4640 psi
Vacuum Service
Full vacuum subject to fill fluid limits. Refer to table A.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a seal ofspecific size/type)
referred to silicone oil (DC 200) filling and AISI 316 L ss diaphragmmaterials.
For filling different from silicone oil (DC200) the errors can be multipliedby ratio between the thermal expansion coefficients of the selectedfilling divided by the one of DC200, listed in the fill fluid characteristicstable.
THE ERRORS IN TABLE CAN BE CONSIDERED DIVIDED BY 4 FORTRANSMITTERS USING SAME REMOTE SEAL ON THE TWO SIDES
Flange ASME 600, 3in Threaded Flange ASME 2500, 2in
ecivreSaerUeziSlaeSdegnalF
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
1 1/2 ni Hni6.5,rabm41,aPk4.1 2O Hni42.2,rabm6.5,aPk65.0 2O Hni2.7,rabm81,aPk8.1 2O
2 1/2 ni Hni88.0,rabm2.2,aPk22.0 2O Hni4.0,rabm1,aPk1.0 2O Hni63.0,rabm9.0,aPk90.0 2O
131
(5.1
6)45
(1.7
7)
dia 155 (6.10)
no. 4 holesdia 25.4 (1)
dia 53(2.08)
dia37.5(1.47)
~15
(0.5
9)
dia 110 (4.33)
dia 60(2.36)
2(0.07) ANSI B2.1 NPS
69 or 94(2.71 or 3.7)
69(2.71)
dia 127 (5)
3.5
(0.1
4)
31.8
(1.2
5)
6.4
(0.2
5)
40.3
(1.
59)
dia 168.3 (6.63)
dia 209.6 (8.25)
no. 8 holesdia 22.2 (0.87)
2600T Pressure TransmittersModels S264 SS/S264_8
39
BASIC ORDERING INFORMATION model S264P Remote Seal for Urea ServiceSelect one character or set of characters from each category and specify complete catalog number.
Note 1: Not available with Size/Mounting flange code J
Note 2: Not available with Size/Mounting flange code H
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 P X X X X X X X X
ecivreSaerUroflaesetomeR
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
lairetaM/gnitargnitnuoM/eziS 7– ht retcarahcni3ni2
FR006EMSAegnalfdedaerhT
edarGaerUssL613ISIAleetsnobraC
HJ
retemaiD/htgnelnoisnetxE – 8 ht retcarahc
)ni95.1(mm3.04)ni95.1(mm3.04
)ni61.5(mm131
ni7.2(mm96)ni17.3(mm49
)ni74.1(mm5.73
)1etoN()1etoN()2etoN(
RST
)laes(lairetammgarhpaiD 9– ht retcarahc
edarGaerUssL613ISIA S
noitcetorpyrallipaC 01– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 11– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2
)01(3)21(5.3
)31(4)51(5.4
)71(5)81(5.5
)02(6
ABCDEFGHJKL
diulflliF 21– ht retcarahc
lioenociliSerutarepmethgihroflioenocilIS
SH
noitpO 31– ht retcarahc
enoNtsetyeuH
13
2600T Pressure TransmittersModels S264 SS/S264_8
40
S264B Model Button Type Remote Seal (To be used only for gauge pressure)These remote seals are designed to connect directly to a process pipe via the NPT threaded connection or to match pipe fitting withan interface suitable for the provided mating flange. The button seals, due to their design, are dedicated for measurement with medium/high calibrated span (2 MPa/20 bar/290 psi approx. or greater).
3 1/4in flange extended - type 91
3 1/2in flange extended - type 91 modified
1 1/2in threaded uniontype 92/92 modified
Flange
Spacer
Flange Spacer
6.35 (1/4)
13.49 (17/32)
19 (3/4)
2.3 (3/32)Thick Gasket
146 (5-3/4)
dia
83 (3
-1/4
)
4 Holes equally spaced33/64in dia on2-1/8in dia Bolt Circle
2 Holes5/16-18NC–2 on2-1/8in Dia Bolt Circle
51 (2)
dia 24 (15/16)dia 23 (59/64)
dia
35 (1
-3/8
)di
a 34
(1-2
3/64
)
dia 24 (15/16)dia 23 (59/64)
6.35 (1/4)
13.49 (17/32)
128 (5-1/32)25 (1)
2.3 (3/32)Thick Gasket
212 (8-11/32) Max
dia
89 (3
-1/2
)
4 Holes equally spaced17/32in dia on2-1/2in dia Bolt Circle
2 Holes1/2-13NC–2 on2-1/2in Dia Bolt Circle
dia
35 (1
-3/8
)di
a 34
(1-2
3/64
)
dia 24 (15/16)dia 23 (59/64)
19 (3/4) 38 (1-1/2)
146 (5-3/4)
2.3 (3/32)Thick Gasket
dia
24 (1
5/16
)di
a 23
(59/
64)
76 (3) 6.35 (1/4)
13.49 (17/32)
1-1/2 16N-2 for Type 921-1/2 12FG for Type 92 modified
2600T Pressure TransmittersModels S264 SS/S264_8
41
Maximum Working Pressure (20 to 120°C; 68 to 248°F)
Types 89, 90 and 92: 42MPa, 420bar, 6090psi
Types 91: 35MPa, 350bar, 5075psi
Vacuum Service
Full vacuum subject to fill fluid limits.
Refer to table A.
Process Temperature Limits
Same as fill fluid limits. Refer to table A.
Temperature effect
The following table shows the temperature effect for 20K (36°F)change, detailed separately for
a) the seal (one element)
b) the capillary per meter
c) the system (transmitter sensor when combined with a seal ofspecific size/type)
referred to silicone oil for high temperature filling and Hastelloy C276diaphragm materials.
epyTnottuBeziSlaeS
rorrelaeS rorrEyrallipaCm1 rorrE)rosneS(metsyS
ni1 Hni23,rabm08,aPk8 2O Hni27,rabm81,aPk8.1 2O Hni8.21,rabm23,aPk2.3 2O
Capillary toinstrument
Bracket – type 89
Universal– type 90
dia 24 (15/16)dia 23 (59/64)
13.49 (17/32)
28.58 (1-1/8) 2.3 (3/32)Thick Gasket
dia 33.34 (1-5/16 )
6.35 (1/4)
125.41 (4-15/16)
138.
11 (5
-7/1
6)
dia 22.23 (7/8)
95.25 (3-3/4)
60.33 (2-3/8)
47.6 (1-7/8) 30.16 (1-3/16)
21.4
3 (2
7/32
)
42.8
6 (1
-11/
16)
2 Holesdia 17.46 (11/16)
6.35 (1/4)
13 (17/32)
78 (3-1/16)
52 (2-1/16)
146 (5-3/4)
2.3 (3/32)Thick Gasket
dia 24 (15/16)dia 23 (59/64)
2600T Pressure TransmittersModels S264 SS/S264_8
42
BASIC ORDERING INFORMATION model S264B Button Type Remote SealSelect one character or set of characters from each category and specify complete catalog number.
Note 1: Only available with Bracket type 89 version and suitable for food application
LEDOMESAB 1– ts 5ot ht sretcarahc S 2 6 4 B X X X X X X X X X
)RETTIMSNARTHCAEROFYLNOENOEBTSUM(laesetomerepytnottuB
–noitcennocfoedisrettimsnarT 6 ht retcarahcedishgiHediswoL
HL
eziS 7– ht retcarahcni1 M
epytnoitcennocgnitnuoM – 8 ht retcarahc
3 1/4 19epyt–dednetxeegnalfni3 1/2 deifidom19epyt–dednetxeegnalfni1 1/2 29epyt–noinudedaerht2-N61ni1 1/2 deifidom29epyt–noinudedaerhtFN21ni
98epyt–tekcarB09epyt–lasrevinU
ABCFDE
)laes(lairetammgarhpaiD 9– ht retcarahc
™672CyolletsaH H
noitcetorpyrallipaC 01– ht retcarahc
ruomrassL613ISIArevocevitcetorpCVPhtiwruomrassL613ISIA
)ERUTAREPMETHGIHROFDEDNEMMOCER( AB
)teef(mhtgnelyrallipaC 11– ht retcarahc
)3(1)5(5.1
)7(2)8(5.2)01(3
ABCDE
diulflliF 21– ht retcarahc
lioenociliSerutarepmethgihroflioenocilIS
)devorppaADF(liolareniM )1etoN(
SHW
noitpO 31– ht retcarahc
deriuqertoN)98epytrofton(ssecorproflavomerlaesrofralloctuokcaJ
12
teksaG 41– ht retcarahc
enoNmuinimulA
ss613ISIA
1EF
2600T Pressure TransmittersModels S264 SS/S264_8
43
™ Hastelloy C276 is a Cabot Corporation trademark
™ Hastelloy C2000 is an Haynes International trademark
™ Monel is an International Nickel Co. trademark
™ Viton is a Dupont de Nemour trademark
™ DC200 is a Dow Corning Corporation trademark
™ Galden is a Montefluos trademark
™ Halocarbon is a Halocarbon Products Co. trademark
™ AN140 is a Wacker-Chemie trademark
™ Neobee M20 is a Stepan Company trademark
™ Marcol is a Esso Italiana trademark
™ Syltherm is a Dow Chemical Company trademark
2600T Pressure TransmittersModel S264
SS
/S26
4_8
ABB has Sales & Customer Supportexpertise in over 100 countries worldwide
www.abb.com/instrumentation
The Company’s policy is one of continuous productimprovement and the right is reserved to modify the
information contained herein without notice.
Printed in Italy (12.2008)
© ABB 2008
ABB LtdHoward Road, St. NeotsCambridgeshire, PE19 8EUUKTel: +44(0)1480 475321Fax: +44(0)1480 217948
ABB Inc.125 E. County Line RoadWarminster, PA 18974USATel: +1 215 674 6000Fax: +1 215 674 7183
ABB SACEA division of ABB S.p.A.Via Statale 11322016 Lenno (CO) ItalyTel: +39 0344 58111Fax: +39 0344 56278