ClearFlex ME
For more information or for the Triangle sales person in your
area, please contact:
INX Digital International Co.2125 Williams StreetSan Leandro, CA
94577+1 510.895.8001 tel800.895.8001 toll free+1 510.895.8080
[email protected]
Website:www.INXdigital.comwww.greenINX.com
ClearFlex MED320 is a premium, extremely durable, waterborne,
clear coat-ing. Containing both ultraviolet absorbers and hindered
amine light stabilizers for the maxi-mum in UV light
protec-tion.
ClearFlex ME is a fourth generation product formulated to
protect digitally produced images that have been applied to exible
vinyl to pop color development, waterproof and seal, and to provide
ultraviolet light and abrasion resistance. Advantages include:
UV inhibiting--Long lasting Good abrasion resistance Chemical
resistant to gasoline, oils, diesel fuel, and detergent. RF
weldable Non-yellowing Fast dry*, low odor Flexible Very resistant
to water exposure Easy water cleanup Low VOC DOT nonhazardous
*Slower to dry in very high humidity. Full curing may be
aected.
UV PERFORMANCETest results show that a one mil (0.001 inch or
25.4 microns) dry lm, when applied in two applications of 0.5 mils
each, blocks >90% transmission of ultraviolet light. UV
protection extends the color life of the image.
PHYSICAL PROPERTIESVOC: [averaged as packed] .. 235g/l
(1.96#/gal)[Check your local air quality control regulations for
compliance as this coating may not be suitable for your application
surface or use in communi-ties with VOC regulations.
APPEARANCE:D320.........................Gloss........................80
5
WEIGHT PER LITER: [average]........ 2.4lbs
FLASH POINT: [setaash]............ >200F
PACKAGE VISCOSITY: ....28-32 #2 Zahn Cup
SOLIDS: [average] By Weight.............. 33.5 2% By
Volume............. 31.5 2%
COVERAGE: [average]Theoretical at 1/2 mil DFT....1010
sqft/galTheoretical at 1 mil DFT...........505 sqft/galRecommended
min. DFT...................... 1 mil
DRY SCHEDULE: [at 50% RH and 1 mil DFT
Touch
Recoat
Hard Cure
50F 60F 70F 85F
2 hrs
2 hrs
1 hr
1 hr
4 hrs 2 hrs8 hrs 1 hr
15 mins
30 mins 15 mins
30 mins
MINIMUM AIR DRY TEMPERATURE: ..... 50F
FORCED CURE: [@ 190F] ............... 15 mins
ORDER NUMBER AND
COLOR:D320.......................................... Clear UV
Gloss
PACKAGING:Six each 1 liter bottle per case........... 15lbs4
each 5 liter jugs per case.............. 595 lbs1 each 20 liter jug
per case............... 49 lbs
This information has been carefully studied from experience
gained in the laboratory and under commercial situations. It is
subject to change without notice. All sales are subject to our
standard terms and conditions of sale. Since applications vary
tremendously, the user assumes the obligation to test this product
in their specic situation to determine its suitability an assumes
all risk and liability related to such use. INX Digital
International Co. makes no warranty, express or implied, for the
use of the product for any particular application. In no event
shall INX Digital International Co. be liable for damages in excess
of the original cost of the product nor shall INX Digital
International Co. be liable for any special or consequential
damages. The Triangle logo is a registered trademark of Triangle
Coatings, Inc. used under license.
Technical Data Sheet
This information has been carefully studied from experience
gained in the laboratory and under commercial situations. It is
subject to change without notice. All sales are subject to our
standard terms and conditions of sale. Since applications vary
tremendously, the user assumes the obligation to test this product
in their specic situation to determine its suitability an assumes
all risk and liability related to such use. INX Digital
International Co. makes no warranty, express or implied, for the
use of the product for any particular application. In no event
shall INX Digital International Co. be liable for damages in excess
of the original cost of the product nor shall INX Digital
International Co. be liable for any special or consequential
damages. The Triangle logo is a registered trademark of Triangle
Coatings, Inc. used under license.
Technical Data Sheet
APPLICATION DATASURFACE PREPARATIONClean surface thoroughly of
foreign contaminants.
Vinyl: apply one or two coats to provide 1 mil dry lm
thickness.*+
THINNING:This is a water soluble product. Thinning is not
recommended as it will reduce the eectiveness of the product.
APPLICATION METHODS:Hand Application: Use a 1/4 inch close nap
roller for the best performance on large surfaces. For small
pictorial areas or digital prints, brushing is better using a 4
inch foam brush or foam paint pad.Always load the applicator with
the maximum amount of coating as possible and apply with light
pressure. This will prevent bubbling. Vigorous rolling and high
pressure may produce a frothy surface.
Spray Application: Do not use Wagner or airless spray equipment.
This type of equipment puts too much material on the surface. Use
conventional air atomiza-tion equipment. Fluid tip size should be
0.045 - 0.060 at 30 pounds atomizing pressure at 9 - 12 cfm.
*Since applications for this product vary tremen-dously, the
user assumes the obligation to test this product in their specic
application to determine the suitability for reach application and
assumes all risk and liability related to such use.
+ Do not leave digital prints folded face-to-face sitting on hot
asphalt - they may stick together, damaging the image.
AUTOMATIC APPLICATION
For automatic application using the Seal AquaSeal 1600 or 3200
series liquid laminator, ll the machines reservoir 3/4 full and
0-10% water to reduce.
Using more water will result in thinner laminate and less
protection. Remem-ber, at 10% reduction with one pass will give a
lm not exceeding 1/2 mil. For full protection use D320 unthinned
and apply two more coats.
UV PERFORMANCETest results show that a one mil (0.001 inch/25.4
microns) dry lm, when applied in two applications of 0.5 mil each,
blocks >90% transmission of ultraviolet light.
LIMITATIONS: ALWAYS TEST BEFORE USE!Do not apply to murals that
have been applied to walls or any surface that is subject to water
absorption or nega-tive hydrostatic pressure. Do not apply to
exible vinyl that will be rolled and stored in high humid
temperatures. This coating may crack or delaminate on high gloss
blackout vinyl when the vinyl is aggressively seam sown. Not for
use on NON-waterproof paper substrates.
CLEANUP SOLVENT: Water or MEK (methyl ethyl ketone) for dried
spots.
SAFETY AND HANDLING
FLASH POINT: [Setaash] .............. >200F
SHIPPING DESCRIPTION: [CFR 49] Ground/Air/Vessel: Non regulated
material
Required Label & Marking: Not required
IMDG Packaging: Not required
IMDG Stowage: Not regulated
UNIFORM FIRE CODE: [cfr 29]: Class III-A
STORAGE TEMPERATURE: 120 F max
SHELF LIFE: [warranted] 1 year
HMIS RATINGS: H - 1; F - 1; R - 0, PP - B
www.INXdigital.com
D320 front_1D320 back_1
