Customer Training - ARBURG · 8 Course objective: Basic principles of injection moulding machines and control systems Target group: Those new to the injection moulding sector,

ww

w.a

rbur

g.co

.uk

Great Britain

2018

Customer Training

3

Dear Customer,

The trademark of the ARBURG ALLROUNDER is its

versatility and flexibility. It is important therefore

that you, the end user, should be able to obtain a

full understanding and appreciation of its full capability.

For this particular reason ARBURG Ltd have put together this booklet to

offer you and your technicians the possibility of participating in training

courses which will enable you to acquire all the skills required to work

with the ALLROUNDER range of injection moulding machines.

Contained within this booklet is the current ARBURG training pro-

gramme subdivided into different courses according to your specific

requirements. These courses cover a wide cross section of disciplines

from the general practice of injection moulding through to in depth

theoretical and ‘hands on’ training on the machines.

Should you have questions or require any further information please do

not hesitate to contact us.

Yours faithfully

Colin Tirel

Managing Director

ARBURG LIMITED

Introduction

4

General Information

Courses are arranged according

to demand. Please E-Mail your

request to [email protected] or

telephone 01926 457000

Times and Duration

for courses at Warwick:

Day 1: 9.30–16.30

Day 2: 9.30–16.30

Times and Duration for courses

at customer’s premises:

Dependant on course and location.

Costs:

One day course at ARBURG Ltd

£ 250.00 per delegate & VAT sub-

ject to a minimum of 3 attendees.

Two day course at ARBURG Ltd.

£ 400.00 per delegate & VAT. Includ-

ed in the price is a detailed course

book, lunch and beverage subject to

a minimum of 3 attendees.

Two day course conducted at cus-

tomer premises in Wales and Eng-

land £ 1300.00 per course & VAT.

Training courses conducted at

customer premises in Ireland and

Scotland prices upon request.

Course enquiries are also possible

via our website.

Note:

All courses are available subject

to machine availability and a

minimum number of participants

having registered.

Should you require advice on

the suitability of courses for your

requirements please contact either

Mr. R Hambrook (Service Manager)

or Mr. Derek Cheetham (Applica-

tions Engineer). General course

enquiries should be made to

Donna White.

All enquiries regarding training

at customer premises should be

made to Mr. R Hambrook.

Special bespoke machine training

courses or information seminars

can be arranged for individual

customers at our facility at a cost

of £ 650 per day irrespective of

number of personnel but a maxi-

mum of 6 is recommended.

Worldwide standards:

ARBURG places high demands

on its trainers. All our courses are

carried out according to a unified

standard worldwide.

5

Local Hotel Information

Accommodation:

We have listed for your informa-

tion a list of local hotels and

contact telephone/fax numbers.:

It is the customer’s responsibility

to arrange their accommodation

and the payment of same.

In the case of late bookings we

can of course assist with hotel

booking but on the strict un-

derstanding that hotel costs will

be settled by the customer on

departure.

The Falstaff, Leamington Spa

Approx. 2 miles from ARBURG Ltd

Tel.: 01926 312044

Fax: 01926 450574

The Holiday Inn Express,

Warwick


Reservations: 0800 897121

The Angel, Leamington Spa


Tel.: 01926 881296

Woodland Grange,


Tel.: 01926 336621

6

Spares Department: 01926 457021

Darren Hunt, Spares

Service Department: 01926 457031

Robin Hambrook, Service Manager

Roger Talbot, Service Controller

Kim Sharpe, Internal Customer

Service Engineer, Stephen Redman-

Windsor, Service Contract and

Support Administrator

General: 01926 457000

Colin Tirel, Managing Director

Lorraine McSharry, Finance Controller

Donna White, PA to the directors

Derek Cheetham, Applications Eng.

Matt Knight, Automation Engineer

ARBURG Ltd Warwick

ARBURG Ltd

Tachbrook Park Drive

Warwick CV34 6RH

Tel.: 01926 457000

Fax: 01926 457030

www.arburg.co.uk

E-Mail: [email protected]

[email protected]

[email protected]

ARBURG Ltd

Sales Department:

01926 457001

Simon Wrighton, Sales Director

David Kenny, New M/C Sales

Vince Crossan, New M/C Sales

Training Place/Address/Contact List

7

Courses Overview

Basic courses p. 10

Introductory course on machine operation

Machine adjustment courses p. 11

Main course on machine adjustment and

programming

Service training p. 12-13

Electrical and hydraulic machine appreciation

course

Plastics technology course p. 14

Clamp and injection data considerations and

applications

Information seminar p. 15

One-day seminars on the SELOGICA control and

ARBURG ALS host computer system

Courses on robotic systems p. 16

Six-axis robotic systems, MULTILIFT V /

MULTILIFT SELECT, MULTILIFT H

G

M

SC

KT

I

HP

We are also pleased to offer individualised courses upon

request, with customer-specific content. These courses can be

held either at your premises or at ARBURG.

Machine

Service

One-day seminar

Technology

Automation

8

Course objective: Basic principles of injection moulding machines

and control systems

Target group: Those new to the injection moulding sector,

machine operators

Prerequisites: No previous knowledge required

Course duration: 2 days

Course fee: £ 400.00

Documents: Course folder with accompanying texts and CD

Note: To enhance your knowledge, we also recommend participation in

the machine adjustment courses

Course description

G Basic courses

Course content

• Design of the injection moulding machine

• Injection moulding process

• Basic principles of the control system and the control panels

• Typical plastics processing requirements

• Practical situations: starting / ending the injection moulding

process, troubleshooting / fault remedy, mould changes, chang-

ing the moulding material with cylinder and screw cleaning

• Machine maintenance

Machine Control Code

ALLROUNDER A SELOGICA direct G-A d

ALLROUNDER E SELOGICA direct G-E

ALLROUNDER H SELOGICA direct G-H

ALLROUNDER GE SELOGICA direct G-GE

ALLROUNDER S SELOGICA direct G-S

9

Course content

M Machine adjustment courses

• Typical machine features

• Programming the control system

• Setting up the clamping unit and the injection unit

• Adopting the set values

• Quality monitoring and data recording / backup

• Machine maintenance

Course objective: Adjustment an injection moulding

machine independently

Target group: Installation technicians, machine operator

Prerequisites: Basic knowledge of injection moulding




Course description


ALLROUNDER A SELOGICA direct M-A d

ALLROUNDER E SELOGICA direct M-E

ALLROUNDER H SELOGICA direct M-H

ALLROUNDER GE SELOGICA direct M-GE

ALLROUNDER S SELOGICA direct M-S

10

SC H/M

Course content

Service courses hydraulics / mechanics

• Explanation of the hydraulic circuit diagram

• Explanation of the most important function screens of the

SELOGICA and SELOGICA direct control system

• Pump control

• Operating principle of the injection and clamping units

• Regulating valves

• Measurement and diagnostic options


ALLROUNDER S SELOGICA direct SCS H/M

Course objective: Working with the hydraulic circuit diagram, knowl-

edge of the hydraulic machine sequence, fast fault detection and

rectification

Target group: Service personnel, fitters, electricians, electronics engineers

Prerequisites: Basic knowledge of hydraulics, mechanics



Documents: Course folder with accompanying text and data medium

Course description

11

Course content

SC EL Service courses electrics, electronics

• Explanation of the electric circuit diagram

• Explanation of the most important function screens of the

SELOGICA and SELOGICA direct control system

• Machine sequence, block diagrams

• Regulating valves

• Measurement and diagnostic options


ALLROUNDER S SELOGICA direct SCS EL

Course objective: Working with the electric circuit diagram, knowledge

of the electric machine sequence, fast fault detection and rectification

Target group: Service personnel, electricians, electronics engineers

Prerequisites: Knowledge of electrics and electronics



Documents: Course folder with accompanying text and data medium

Course description

12

Course content

KT 1

Injection moulding materials

• Structure / properties of the plastics

• Condition ranges / fine structure of plastics

• Overview of the most important plastics

Injection moulding process

• Design of the injection moulding machine

• Various injection moulding processes

• Process parameters and their influence on moulded parts

Technology Code

Injection moulding materials /

injection moulding process KT 1

Course objective: Introduction to injection moulding materials and

processing

Target group: Installation technicians, machine operators, production

managers, controllers, sales, designers, planners

Prerequisites: Basic knowledge of injection moulding and

injection moulding materials




Course description

Plastics technology courses Injection moulding materials / injection moulding processs

13

Course content

I SEL

• Requirements on the plastic parts

• Influence of the injection moulding machine

on the moulded parts

• Design of the injection unit and clamping unit

• Function of the control hydraulics of the SELOGICA / SELOGICA

direct control system (control and operating concepts, selection

and configuration of mould, product and order-specific machine

equipment, sequence programming, machine movement

parameter programming, programming monitoring / documen-

tation / help functions, examples of programming steps when

setting up the mould, summary of the SELOGICA / SELOGICA

direct control system)

Subject Code

SELOGICA direct control system options I SEL d

SELOGICA information seminars

Seminar objectives: Familiarisation with the SELOGICA /

SELOGICA direct user interface

Target group: The seminars are aimed at all those wishing to familiar-

ise themselves with the advantages of the SELOGICA / SELOGICA direct

control systems

Seminar duration: 1 day (9.00 a.m. - 3 p.m.) per seminar

Tuition fee: Free of charge

Documents: Detailed seminar documentation

Course description

14

• Operation of the vertically (V) operating MULTILIFT V or

the horizontally (H) operating MULTILIFT H

• Programming of the MULTILIFT on ALLROUNDERs

• Various practical applications: teach-in programming,

programming of sequences, patterned part set-down and

monitoring functions

• Function description of the inputs and outputs

• Data set management

• Maintenance and inspections of the safety equipment

Course objective: Unaided programming of the ARBURG robotic

system MULTILIFT V, SELECT and H

Target group: Programmers of MULTILIFT robotic systems

Requirements: Basic knowledge in the operation of injection moulding

machines



Documents: Course folder and CD

Course description

RP ML

Robotic system Control Code

MULTILIFT V, SELECT SELOGICA ‘direct’ RP ML-V1

Course content

Course on robotic systemsMULTILIFT Programmer - Level 1

16

M40

A425

A425

A445

A429

A452

A452

N

S

EW

1 km

2000 ft

52.27339,-1.54449

ARBURG Ltd.Tachbrook Park Drive | Warwick CV34 6RH

Euro

pa

Way

Old Warwick RdMyton Rd

Stra

tfor

d Rd

Banburg Rd

Emscote Rd

Location map

ARBURG Ltd

Tachbrook Park Drive

Warwick CV34 6RH

Tel.: 01926 457000

Fax: 01926 457030

www.arburg.co.uk

E-Mail: [email protected]

Enrolment for Training Course

Your signature is an acceptance to our non-liability with regard to

personal damage within our premises

To: ARBURG Ltd, Donna White +44 (0) 1926 457020

or post (in separate envelope) to: ARBURG Ltd, Tachbrook Park Drive,

Warwick, CV34 6RH, Attention: Donna White

from: (please complete this form)

O/N Position

Fax

Company:

Address:

Telephone: Fax:

Customer number:

I/We will arrive on:

and depart on:

Date Signature

Course Date Participant`s Names

6800

17_G

B_09

2017

· Su

bjec

t to

alte

ratio

ns

Pr

inte

d in

Ger

man

y

ARBURG GmbH + Co KG

Arthur-Hehl-Strasse · 72290 Lossburg · Tel.: +49 7446 33-0 ·

www.arburg.com · [email protected]

With locations in Europe: Germany, Belgium, Denmark, France, United

Kingdom, Italy, Netherlands, Austria, Poland, Switzerland, Slovakia,

Spain, Czech Republic, Turkey, Hungary | Asia: People’s Republic of

China, Indonesia, Malaysia, Singapore, Taiwan, Thailand, United Arab

Emirates | America: Brazil, Mexico, USA

For more information, please go to www.arburg.com.

© 2017 ARBURG GmbH + Co KGThe brochure is protected by copyright. Any utilisation, which is not expressly permitted under copyright legislation, requires the previous approval of ARBURG.

All data and technical information have been compiled with great care. However we accept no responsibility for correctness. Individual illustra-tions and information may deviate from the actual delivery condition of the machine. The relevant valid operating instructions are applicable for the installation and operation of the machine.

ARBURG GmbH + Co KGDIN EN ISO 9001 + 14001 + 50001 certified