Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
1.1NBNBN/A
2017N/A1
STANDARD DETAILS - PANEL PROFILE
STRUCTURAL PANELS INC
VARIES TO SUIT
46" FIXED WIDTH SHADOW LINE PROFILE
VARIES TO SUIT
46" FIXED WIDTH MICRORIB PROFILE
102mm 102mm25mm
1.52
mm
EXPOSED SURFACE
1.0 EXTERIOR SKIN PROFILES:
A. SHADOWLINE - 1168mm (46") PANEL MODULE
38.1mm 38.1mm 38.1mm
1.52
mm
EXPOSED SURFACE
1.0 EXTERIOR SKIN PROFILES:
B. MICRORIB - 1168mm (46") PANEL MODULE
GENERAL NOTES FOR SPI ISOWALL PANEL
1.0 Material:Panel: 2" - 10" (50.8mm - 254mm) thick
Core: Rigid Expanded Polystyrene (EPS)
Exterior Siding Sheet: Fabricated from Z275 steel material conforming to ASTM A653M grade 230 steel
Profile: Thickness: Finish: Colour:
Shadowline or MicroRib 0.46mm(26ga) Smooth or Embossed prepainted steel Standard White or custom
Interior Liner Sheet: Fabricated from Z275 steel material conforming to ASTM A653M grade 33 steel
Profile: Thickness: Finish: Colour:
Shadowline or MicroRib 0.46mm(26ga) Smooth or Embossed prepainted steel Standard White or custom
GENERAL NOTES FOR SPI ROCKWALL PANEL
1.0 Material:Panel: 2.5" - 10" (63.5mm - 254mm) thick
Core: PERMANENTLY BONDED MINERAL WOOL
Exterior Siding Sheet: Fabricated from Z275 steel material conforming to ASTM A653M grade 230 steel
Profile: Thickness: Finish: Colour:
Shadowline or MicroRib 0.46mm(26ga) Smooth or Embossed prepainted steel Standard White or custom
Interior Liner Sheet: Fabricated from Z275 steel material conforming to ASTM A653M grade 33 steel
Profile: Thickness: Finish: Colour:
Shadowline or MicroRib 0.46mm(26ga) Smooth or Embossed prepainted steel Standard White or custom
1.0NBN/A
2017N/A2
STANDARD DETAILS - BUTT JOINT CORNER
STRUCTURAL PANELS INC
#8 Tek trim screwColour matched OSC flashingSize to suit panel
Sealant
Sealant
#8 Tek trim screw
Sealant
Sealant
#8 Tek trim screw
Colour matched ISC flashing1-1/2"X1-1/2"
Varies 2" (2.5" Rockwall) - 10"
Sealant
Sealant
#8 Tek trim screw@12" OC
#8 Tek trim screw@12" OC
Colour matched OSC flashingSize to suit panel
Isowall or Rockwall 1168mm panel module @90° butt joint corner
ISOMETRIC VIEW
NOT TO SCALE
TYPICAL OUTSIDE CORNER PANEL AND FLASHING ASSEMBLY
PLAN VIEW
NOT TO SCALE
#8 Tek trim screw@12" OC
#8 Tek trim screw@12" OC
Colour matched ISC flashingSize to suit panel
Isowall or Rockwall 1168mm panel module @90° butt joint corner
Sealant
ISOMETRIC VIEW NOT TO SCALE
TYPICAL INSIDE CORNER PANEL AND FLASHING ASSEMBLY
3.0 Typical Corner Installation
3.01 Once Structural Panels Inc Isowall or Rockwall panels have been erected and secured into place flashing must be installed to complete the installation.
3.02 Apply Adfast Adseal 4800 silicone sealant in one continuous bead to inside of flashing so an air tight seal is achieved.
3.03 Flashing is secured to the panel with #8 Tek self-drilling screws installed ½” – 1” from outside edge at 12” OC increments along the length.
NOTE:CORNERS MUST BE PLUMB AND STRAIGHT WITH ADJACENT PANELS CONTACTING EACH OTHER. IF THESE CONDITIONS ARE NOT MET IT IS POSSIBLE THAT ANY SUPPLIED CORNER FLASHINGS WILL NOT FIT PROPERLY.
1.2NBN/A
2017N/A3
STANDARD DETAILS - PANEL JOINT
STRUCTURAL PANELS INC
CFIA accepted 26ga min G-90 Hot Dipped Galvanized steel pre-coated with standard finish[both interior and exterior]
12"
12"
Varies 2"(2.5" Rockwall) - 10"
EPS or Rockwall core
Male Joint
Female Joint
46" Fixed Panel Width
Field applied silicone in panel joint
CFIA accepted 26ga min G-90 Hot Dipped Galvanized steel pre-coated with standard finish[both interior and exterior]
12"
12"
Varies 2"(2.5" Rockwall) - 10"
EPS or Rockwall core
Male Joint
Female Joint
46" Fixed Panel Width
Field applied silicone on surface of panel joint
PLAN VIEW NOT TO SCALE
Internally caulked panel joint
Externally caulked panel joint
PLAN VIEW NOT TO SCALE
Panel Thickness
Isowall or Rockwall* panel joint
ISOMETRIC VIEW
* NONCOMBUSTIBLE ROCKWALL CONSTRUCTION ONLY. FOR FIRE RATED SYSTEM DETAILS PLEASE REFER TO FIRE RATED DRAWING SET.
0NBN/A
2017N/A4
STANDARD DETAILS - BASE CONNECTIONS
STRUCTURAL PANELS INC
Varies
Isowall or RockwallWall panel
112"
Varies to suit panel
Nail-in anchor
Tek screw #8 x 3/4
AdFast sealant
"U" channel base
SECTION VEIW NOT TO SCALE
Varies
Isowall or RockwallWall panel
Varies to suit panel
Tek screw #8 x 3/4
Tek 5 through panel fastener
Colour matched base trim
Gauged steel base 'L' with dripFastened with nail-in anchors
Sealed with AdFast sealant
*varies
SECTION VEIW NOT TO SCALE
INSTALLING ISOWALL OR ROCKWALL PANELS FROM STRUCTURAL PANELS INC
CONCRETE FLOOR:
1.0 PANEL INSTALLATION:
1.1 Apply AdFast sealant to concrete floor as shown beneath U-channel base.
1.2 Install U-channel base in desired location, fastening U-channel to concrete floor using ¼”X1” nail in fasteners at 16” OC minimum. Special care should be taken to ensure a straight run is maintained for proper installation.
1.3 Stand panel into place and fasten bottom of panel to U-channel using #8 Tek trim screws at 12” OC.
1.4 Stand each additional panel and slide into position and engage lips of adjacent panel. Maintain uniform side joints in order to maintain panel module. Once panel is engaged and in position, repeat step 1.3.
1.5 Repeat steps 1.3 and 1.4 until all wall panels are standing and secured in desired position.
INSTALLING ISOWALL OR ROCKWALL PANELS FROM STRUCTURAL PANELS INC
CONCRETE CURB:
1.0 PANEL INSTALLATION:
1.1 Apply AdFast sealant to concrete curb as shown beneath drip base.
1.2 Install drip base in desired location, fastening drip to concrete floor using ¼”X1” nail in fasteners at 16” OC minimum. Special care should be taken to ensure a straight run is maintained for proper installation.
1.3 Stand panel into place and fasten bottom of panel to drip base using Tek 5 screws, 3 screws per panel minimum.
1.4 Stand each additional panel and slide into position and engage lips of adjacent panel. Maintain uniform side joints in order to maintain panel module. Once panel is engaged and in position, repeat step 1.3.
1.5 Repeat steps 1.3 and 1.4 until all wall panels are standing and secured in desired position.
Nail-in anchor
AdFast 1802Urethane Sealant
Galvanized or colour matched base drip flashing
Offset base flashing.Colour matched to panel
Isowall or Rockwall Wall panel
#8 Tek trim screws@12" OC
Nail-in anchor
AdFast 1802Urethane Sealant
Galvanized or colour matched base drip flashing
U-channel base flashingColour matched to panel
Isowall or Rockwall Wall panel
#8 Tek trim screws@12" OC
ISOMETRIC VIEW
ISOMETRIC VIEW
0NBN/A
2017N/A5
STANDARD DETAILS - WALL TO CEILING
STRUCTURAL PANELS INC
Colour matched OSC flashingSize to suit panel
#8 Tek trim screw
Sealant
Sealant
#8 Tek trim screw
Sealant
Sealant
#8 Tek trim screw
Colour matched ISC flashing1-1/2"X1-1/2"
Varies 2"(2.5" Rockwall) - 10"
Varies 2"(2.5" Rockwall) - 10"
Wall panel
Ceiling panel
Sealant
Sealant
#8 Tek trim screw
Colour matched ISC flashing1-1/2"X1-1/2"
Varies 2"(2.5" Rockwall) - 10"
Varies 2"(2.5" Rockwall) - 10"
Sealant
Sealant
#8 Tek trim screw
Colour matched ISC flashing1-1/2"X1-1/2"
Ceiling panel
Wall panel
WALL TO CEILING CONNECTION
WALL TO CEILING CORNER
SECTION VIEW NOT TO SCALE NOT TO SCALESECTION VIEW
#8 Tek trim screws@12" OC
Colour matched OSC flashingSize to suit panel
Ceiling panel
Sealant
Colour matched ISC flashing1-1/2"X1-1/2"
Wall panel
Colour matched ISC flashing1-1/2"X1-1/2"
Ceiling panel
Wall panel
#8 Tek trim screws@12" OC
Sealant
ISOMETRIC VIEW ISOMETRIC VIEW
0NBN/A
2017N/A7
STANDARD DETAILS - Penetration Flashing
STRUCTURAL PANELS INC
Urethane sealant around perimeter of cut-out
Install penetrant through cut-out
Install flashing around penetrant.
Fasten flashing to panel using self drilling trim scres.
Seal flashing to penetrant using urethane sealant.
Urethane sealant in panel joint, continous into
cut-out.