Curriculum & Syllabus of M.E. Applied Electronicsksrct.ac.in/admin/file_manager/source/academic/curriculum/ME_AE_R...... CMOS transistor theory and logic design. ... Circuit using

Curriculum & Syllabus

of

M.E. Applied Electronics

(For the batch admitted in 2010-11 onwards)

K.S.RANGASAMY COLLEGE OF TECHNOLOGYTIRUCHENGODE – 637 215

(An Autonomous Institution affiliated to Anna University Chennai and approved by AICTE New Delhi)

BoS Chairman Prepared By PAE: M.E. APPLIED ELECTRONICS - REGULATION 2010 - SYLLABUS

2

K.S.Rangasamy College of Technology -Autonomous Regulation R 2010

Department Electronics and CommunicationEngineering

Programme Code & Name PAE : M.E. Applied Electronics


3

K.S.Rangasamy College of Technology , Tiruchengode - 637215Curriculum for the Programmes under Autonomous Scheme

Regulation R 2010Department Department of Electronics and Communication EngineeringProgramme Code & Name PAE : M.E. Applied Electronics

Semester ICourseCode Course Name

Hours/ Week Credit Maximum marksL T P C CA ES Total

THEORY10 PAE 101 Applied Mathematics (PAE, PVL) 3 1 0 4 50 50 100

10 PAE 102 VLSI Design Techniques (PAE,PVL) 3 0 0 3 50 50 100

10 PAE 103 Advanced Digital System Design(PAE, PVL) 3 1 0 4 50 50 100

10 PAE 104 Embedded Systems (PAE, PVL) 3 0 0 3 50 50 10010 PAE 105 Digital Control Engineering 3 1 0 4 50 50 10010 PAE E1* Elective I 3 0 0 3 50 50 100

PRACTICAL10 PAE 106 VLSI Simulation Laboratory 0 0 3 2 50 50 10010 PAE 107 Embedded Systems Laboratory 0 0 3 2 50 50 100

Total 18 3 6 25 800Semester II

CourseCode Course Name


THEORY10 PAE 201 CAD of VLSI Circuits (PAE, PVL) 3 0 0 3 50 50 10010 PAE 202 Analog VLSI circuits (PAE, PVL) 3 0 0 3 50 50 100

10 PAE 203Advanced Computer Architectureand Parallel Processing (PAE,PVL)

3 0 0 3 50 50 100

10 PAE 204 Advanced Digital SignalProcessing 3 1 0 4 50 50 100

10 PAE E2* Elective II 3 0 0 3 50 50 10010 PAE E3* Elective III 3 0 0 3 50 50 100

PRACTICAL

10 PAE 205 Electronics System DesignLaboratory 0 0 3 2 50 50 100

10 PAE 206 Technical Report Preparation andPresentation 0 0 2 0 100 00 100

Total 18 1 5 21 800


4

K.S.Rangasamy College of Technology , Tiruchengode – 637215Curriculum for the Programmes under Autonomous Scheme


Semester IIICourseCode Course Name


THEORY

10 PAE 301 ARM Architecture andProgramming (PAE, PVL) 3 0 0 3 50 50 100

10 PAE E4* Elective IV 3 0 0 3 50 50 10010 PAE E5* Elective V 3 0 0 3 50 50 100

PRACTICAL10 PAE 302 Project Work – Phase I 0 0 12 2 100 00 100

Total 9 0 12 11 400Semester IV

CourseCode Course Name


PRACTICAL10 PAE 401 Project Work – Phase II 0 0 40 10 50 50 100

Total 0 0 40 10 100


5

K.S.Rangasamy College of Technology , Tiruchengode - 637215Curriculum for the Programmes under Autonomous Scheme


Course Code Course NameHours/ Week Credit Maximum marksL T P C CA ES Total

Electives10 PAE E01 Nano Electronics 3 0 0 3 50 50 10010 PAE E02 Neural Networks and Its Applications 3 0 0 3 50 50 100

10 PAE E03 Semiconductor Memory Design andTesting 3 0 0 3 50 50 100

10 PAE E04 Low Power VLSI Design 3 0 0 3 50 50 10010 PAE E05 Computational Intelligent Techniques 3 0 0 3 50 50 100

10 PAE E06 DSP Processor Architecture andprogramming 3 0 0 3 50 50 100

10 PAE E07 VLSI Signal Processing 3 0 0 3 50 50 10010 PAE E08 MEMS System Design 3 0 0 3 50 50 10010 PAE E09 System on Chip 3 0 0 3 50 50 10010 PAE E10 Physical Design of VLSI Circuits 3 0 0 3 50 50 10010 PAE E11 Digital Image processing 3 0 0 3 50 50 100

10 PAE E12 High Performance CommunicationNetwork 3 0 0 3 50 50 100

10 PAE E13 Linear Algebra 3 0 0 3 50 50 10010 PAE E14 Industrial Automation and Control 3 0 0 3 50 50 100

10 PAE E15 Synthesis and Optimization of DigitalCircuits 3 0 0 3 50 50 100

10 PAE E16 Medical Imaging Techniques 3 0 0 3 50 50 10010 PAE E17 ASIC Design 3 0 0 3 50 50 100

10 PAE E18 Digital Signal Processing IntegratedCircuits 3 0 0 3 50 50 100

10 PAE E19 Bio Medical Signal Analysis 3 0 0 3 50 50 10010 PAE E20 Internetworking and Multimedia 3 0 0 3 50 50 10010 PAE E21 Wavelet Transforms and Applications 3 0 0 3 50 50 100

10 PAE E22 Research Methodology - Engineering AndManagement Studies 3 0 0 3 50 50 100


6

K.S.Rangasamy College of Technology - Autonomous Regulation R 2010

Department Electronics and CommunicationEngineering Programme Code & Name PAE : M.E. Applied

ElectronicsSemester I

Course Code Course NameHours/ Week Credit Maximum Marks

L T P C CA ES Total

10 PAE 101 APPLIED MATHEMATICS(PAE, PVL) 3 1 0 4 50 50 100

Objective(s)To develop efficient algorithms for solving numerical methods, to acquire skills in handlingsituation involving random variable. To learn the basics and gained the skill for specializedstudies and research.

1 LINEAR ALGEBRAIC EQUATION AND EIGEN VALUEPROBLEMS Total Hrs 12

System of equations- Solution by Gauss Elimination, Gauss-Jordan and LU decomposition method- Jacobi,Gauss-Seidal iteration method- Eigen values of a matrix by Jacobi and Power method.

2 WAVE EQUATION Total Hrs 12Solution of initial and boundary value problems- Characteristics- D’Alembert’s Solution - Significance ofcharacteristic curves - Laplace transform solutions for displacement in a long string - a long string under itsweight - a bar with prescribed force on one end- free vibrations of a string.

3 SPECIAL FUNCTIONS Total Hrs 12Bessel’s equation - Bessel Functions- Legendre’s equation - Legendre polynomials - Rodrigue’s formula -Recurrence relations- generating functions and orthogonal property for Bessel functions - Legendrepolynomials.

4 RANDOM VARIABLES Total Hrs 12One dimensional Random Variable - Moments and MGF – Binomial, Poisson, Geometrical, NormalDistributions- Two dimensional Random Variables – Marginal and Conditional Distributions – Covariance andCorrelation Coefficient - Functions of Two dimensional random variable.

5 QUEUEING THEORY Total Hrs 12Single and Multiple server Markovian queueing models - Steady state system size probabilities – Little’sformula - priority Queues -M/G/1 queueing system – P.K. formula.Total hours to be taught 60Reference(s) :1 Sankara Rao.K. “Introduction to Partial Differential Equation “, PHI, 1995.2 Taha. H.A., “Operations Research - An Introduction “ 6th Edition, PHI, 1997.

3 Jain M.K. Iyengar, S.R.K. & Jain R.K., “International Methods for Scientific and EngineeringComputation”, New Age International (P) Ltd, Publishers 2003.


7



Programme Code &Name

PAE : M.E. AppliedElectronics

Semester I


L T P C CA ES Total

10 PAE 102 VLSI DESIGN TECHNIQUES(PAE, PVL) 3 0 0 3 50 50 100

Objective(s) To learn the CMOS processing technology and basic CMOS circuits, CMOS transistor theoryand logic design. To study about verilog HDL Programme

1 INTRODUCTION TO MOS TRANSISTOR THEORY Total Hrs 9MOS transistors, CMOS logic, MOS transistor theory – Introduction, Enhancement mode transistor action, IdealI-V characteristics, Simple MOS capacitance Models, Detailed MOS gate capacitance model, Detailed MOSDiffusion capacitance model, Non ideal I-V effects, DC transfer characteristics, VLSI Design flow.

2 CMOS TECHNOLOGY AND DESIGN RULE Total Hrs 9CMOS fabrication and Layout, CMOS technologies, P-Well process, N-Well process, twin-tub process, MOSlayers stick diagrams and Layout diagram, Layout design rules, Latch up in CMOS circuits, CMOS processenhancements, Technology – related CAD issues, Fabrication and packaging.

3 CIRCUIT CHARACTERISATION & PERFORMANCEESTIMATION Total Hrs 9

Determination of Pull-up to Pull-down ratio for NMOS inverter, super buffers, Driving large capacitance loads,Circuits families, transmission gates, Delay estimation, Power dissipation, Design margin, Scaling of MOSCircuits.

4 VLSI SYSTEM COMPONENTS CIRCUITS Total Hrs 9Multiplexers, Decoders, comparators, priority encoders, Shift registers. Arithmetic circuits – Ripple carryadders, Carry look ahead adders, High-speed adders, Multipliers

5 VERILOG HARDWARE DESCRIPTION LANGUAGE Total Hrs 9Overview of digital design with Verilog HDL, hierarchical modeling concepts, basic concepts, modules and portdefinitions, gate level modeling, data flow modeling, behavioral modeling, task & functions, Test Bench.Total hours to be taught 45Reference(s) :

1 Neil H.E.Weste, David Harris and Ayan Banerjee, “CMOS VLSI Design a circuits and systemsperspective, Third Edition, Pearson Education, 2010.

2 Douglas A.Pucknell and Kamran Eshraghian, “Basic VLSI Design”, Third Edition, Prentice-Hall ofIndia2004.

3 Samir Palnitkar, “Verilog HDL a Guide to Digital Design and Synthesis”, Second Edition, PearsonEducation, 2010.

4 John P.Uyemura “Introduction to VLSI Circuits and Systems”, Wiley India Edition, 2006.

5 Neil H.E. Weste and Kamran Eshraghian, Principles of CMOS VLSI Design, Pearson Education ASIA,2nd edition, 2000.


8





L T P C CA ES Total

10 PAE 103 ADVANCED DIGITAL SYSTEMDESIGN(PAE, PVL) 3 1 0 4 50 50 100

Objective(s) To learn how to design programmable logic circuits, logic synthesis compiler based on VHDL.To determine the types of fault that occur in digital circuits

1 SEQUENTIAL CIRCUIT DESIGN Total Hrs 12Analysis of Clocked Synchronous Sequential Networks (CSSN) Modeling of CSSN –State Stable Assignmentand Reduction – Design of CSSN – Design of Iterative Circuits – ASM Chart – ASM Realization.

2 ASYNCHRONOUS SEQUENTIAL CIRCUIT DESIGN Total Hrs 12Analysis of Asynchronous Sequential Circuit (ASC) – Flow Table Reduction – Races in ASC – StateAssignment – Problem and the Transition Table – Design of ASC – Static and Dynamic Hazards – EssentialHazards – Data Synchronizers – Designing Vending Machine Controller – Mixed Operating ModeAsynchronous Circuits.

3 FAULT DIAGNOSIS AND TESTABILITY ALGORITHMS Total Hrs 12Fault Table Method – Path Sensitization Method – Boolean Difference Method – Kohavi Algorithm – ToleranceTechniques – The Compact Algorithm – Practical PLA’s – Fault in PLA – Test Generation – Masking Cycle –DFT Schemes – Built-in Self Test.

4 SYNCHRONOUS DESIGN USING PROGRAMMABLEDEVICES Total Hrs 12

EPROM to Realize a Sequential Circuit – Programmable Logic Devices – Designing a Synchronous SequentialCircuit using a GAL – EPROM – Realization State machine using PLD – FPGA – Xilinx FPGA – Xilinx 2000 -Xilinx 3000.

5 SYSTEM DESIGN USING VHDL Total Hrs 12VHDL Description of Combinational Circuits – Arrays – VHDL Operators –Compilation and Simulation of VHDLCode – Modelling using VHDL – Flip Flops – Registers – Counters – Sequential Machine – CombinationalLogic Circuits – VHDL Code for – Serial Adder, Binary Multiplier – Binary Divider – complete SequentialSystems – Design of a Simple Microprocessor.Total hours to be taught 60Reference(s) :

1 Donald G. Givone “Digital principles and Design” Tata McGraw Hill 2002.2 John M Yarbrough “Digital Logic appns. and Design” Thomson Learning, 2001.3 Nripendra N Biswas “Logic Design Theory” Prentice Hall of India, 2001.4 Charles H. Roth Jr. “Digital System Design using VHDL” Thomson Learning, 1998.


9





L T P C CA ES Total

10 PAE 104 EMBEDDED SYSTEMS(PAE, PVL) 3 0 0 3 50 50 100

Objective(s) To understand the concept of embedded Architecture and emphasis the knowledge of variousprocessors and embedded networking.

1 EMBEDDED SYSTEMS Total Hrs 9Embedded Computers, Characteristics of Embedded Computing Applications, Challenges in EmbeddedComputing system design, Embedded system design process- Requirements, Specification, ArchitecturalDesign, Designing Hardware and Software Components, System Integration, Formalism for System Design-Structural Description, Behavioral Description, Design Example: Model Train Controller.

2 MICROCHIP PIC MICROCONTROLLER -16F87X Total Hrs 9PIC Microcontrollers 16F87X -PIC development tools-CPU Architecture and pipelining-program memoryconsiderations-register file structure and addressing modes-CPU Registers-Instruction set-Loop Timesubroutine-Interrupts-Timers-Capture mode-compare mode and PWM mode.

3 PIC MICROCONTROLLER PERIPHERAL FEATURES Total Hrs 9I/O Port Expansion-Synchronous serial Port (SSP)-Serial Peripheral Interface (SPI)-, I2C Bus for peripheral chipaccess- Analog to Digital converter- UART – Baud Rate – Data Handling – Initialization, special features- SerialProgramming – Parallel Slave Port.

4 EMBEDDED SYSTEM CO-DESIGN Total Hrs 9Distributed Embedded Architecture- Hardware and Software Architectures, Networks for embedded systems-I2C, CAN Bus, SHARC link ports, Ethernet, Myrinet, Internet, Network-Based design- Communication Analysis,system performance Analysis, Hardware platform design, Allocation and scheduling, Design Example: ElevatorController

5 REAL-TIME OPERATING SYSTEMS Total Hrs 9Semaphores and Shared Data Operating System services – Memory Management, Interrupt Routines in anRTOS environment, Basic design using RTOS. Services –I/O subsystems – Network operating systems –Interrupt Routines in RTOS Environment – RTOS Task scheduling models, Interrupt – IEEEstandard POSIX functions for standardization of RTOS and inter-task communication functions.Total hours to be taught 45Reference(s) :

1 John B Pitman, “Design with PIC Micro controllers”, Pearson Education Asia, fourteenth reprint 2004

2 Wayne Wolf, Computers as Components: Principles of Embedded Computing System Design, MorganKaufman Publishers, 2001.

3 Raj kamal ”Embedded System Architecture, Programming and Design”, Second edition ,Tata McGraw-Hill, 2008.

4 David E. Simon, “An Embedded Software Primer”, Pearson Education Asia, 2001.5 C. M. Krishna and K. G. Shin , Real-Time Systems, ,McGraw-Hill, 1997

6 Frank Vahid and Tony Givargi Embedded System Design: A Unified Hardware/Software Introduction, s,John Wiley & Sons, 2000.


10




Course Code Course NameHours/ Week Credit Maximum MarksL T P C CA ES Total

10 PAE 105 DIGITAL CONTROL ENGINEERING 3 1 0 4 50 50 100

Objective(s) To learn and study about the signal processing in digital control and analysis of sampled datacontrol system. To learn design of digital control algorithms.

1 INTRODUCTION Total Hrs 12Overview of frequency and time response analysis and specifications of control systems - Digitalcontrol systems – basic concepts of sampled data control systems – principle of sampling, quantizationand coding – Reconstruction of signals – Sample and Hold circuits – Practical aspects of choice ofsampling rate -Basic discrete time signals – Time domain models for discrete time systems.

2 MODELS OF DIGITAL CONTROL DEVICES AND SYSTEMS Total Hrs 12Z domain description of sampled continuous time plants – models of A/D and D/A converters – Z Domaindescription of systems with dead time – Implementation of digital controllers – Digital PID controllers –Position, velocity algorithms – Tuning – Zeigler – Nichols tuning method.

3 STATE VARIABLE ANALYSIS Total Hrs 12State space representation of discrete time systems – Solution of discrete time state space equation – Statetransition matrix – Decomposition techniques – Controllability and Observability – Multivariable discretesystems.

4 STABILITY ANALYSIS Total Hrs 12Mapping between S plane and Z plane- Jury's stability test - Bilinear transformation and extended Routharray- Root Locus Method – Liapunov Stability Analysis of discrete time systems.

5 DESIGN OF DIGITAL CONTROL SYSTEM Total Hrs 12Z plane specifications of control system design – Digital compensator design – Frequency responsemethod - State feed back – Pole placement design – State Observers – Digital filter properties –Frequency response – Kalman’s filter.Total hours to be taught 60Reference(s) :

1 Gopal M. “Digital Control and State Variable methods”, Tata McGraw Hill Publishing CompanyLtd., New Delhi, India, 2003.

2 Kuo B.C. “Digital Control Systems”, Oxford University Press, Inc., 2003.3 Ogata K. “Discrete Time Control Systems’, Prent ice Hal l Internat ional”, New Gercy, USA, 2002.4 M.Gopal. “Digital Control Engineering”, New age International (p) Ltd, 1999


11





L T P C CA ES Total

10 PAE 106 VLSI SIMULATIONLABORATORY 0 0 3 2 50 50 100

Objective(s) To teach the programming concepts using Verilog HDL, VHDL and usage of Xillinx ISE Tool.LIST OF EXPERIMENTS

1. Design and Simulation of Arithematic /logic operator circuits using verilog/VHDL2. Modeling of Combinational/Sequential Circuits Using Verilog HDL3. Simulation of schematic /RTL using Xilinx ISE Tool4. ARBITER Design using state diagram in Xilinx-ISE Tool5. Simulation of HDL Netlist using Test bench6. Modeling of MAC unit using verilog / VHDL7. Modeling of ALU using verilog / VHDL8. Design and 8-bit signed multiplication algorithm using verilog / VHDL9. Design and technological mapping of RTL netlist in Xillinx ISE Tool

10. Place & route and back annotation for FPGA


12





L T P C CA ES Total

10 PAE 107 EMBEDDED SYSTEMSLABORATORY 0 0 3 2 50 50 100

Objective(s) To teach programming and interfacing concepts of PIC microcontroller, Flash controller andembedded micro controller.

LIST OF EXPERIMENTS1. Study of different addressing modes Using PIC microcontroller.2. General purpose input output (GP10) ports using PIC microcontroller3. Keyboard Interface using embedded micro controller.4. LED and LCD Interface using PIC Micro controller.5. RTD and Thermocouple Interface using embedded micro controller6. ADC and DAC Interface using embedded micro controller.7. I2C RTC interface using embedded micro controller8. Alarm clock using embedded micro controller.9. Testing RTOS Environment and System Programming using KEIL software.

10. Flash controller programming- Data flash with erase , verify, fusing through ATMEL/INTELtools


13



ElectronicsSemester II


L T P C CA ES Total

10 PAE 201 CAD OF VLSI CIRCUITS(PAE, PVL) 3 0 0 3 50 50 100

Objective(s) To know about the algorithms that are used inside VLSI design automation tools and how thesetools are used to design a VLSI chip.

1 BASIC OF CAD ALGORITHMS Total Hrs 9Introduction to VLSI Design methodologies - Review of Data structures and algorithms - Reviewof VLSI Design automation tools - Algorithmic Graph Theory and Computational Complexity - Tractableand Intractable problems - General purpose methods for combinatorial optimization.

2 LAYOUT DESIGN ALGORITHMS Total Hrs 9Layout Compaction - Design rules - Problem formulation - Algorithms for constraint graph compaction -Placement and partitioning - Circuit representation - Placement algorithms – Partitioning.

3 P&R ALGORITHMS Total Hrs 9Floor planning concepts - Shape functions and floorplan sizing - Types of local routing problems -Area routing - Channel routing - Global routing - Algorithms for global routing.

4 SIMULATION AND SYNTHESIS ALGORITHMS Total Hrs 9Simulation - Gate-level modeling and simulation - Switch-level modeling and simulation -Combinational Logic Synthesis - Binary Decision Diagrams - Two Level Logic Synthesis.

5 SYSTEM MODELING ALGORITHMS Total Hrs 9High level Synthesis - Hardware models - Internal representation - Allocation - Assignment andscheduling - Simple scheduling algorithm - Assignment problem – High level transformations.

Total hours to be taught 45Reference(s) :

1 S.H. Gerez, "Algorithms for VLSI Design Automation", John Wiley & Sons, 2e,2006

2 N.A. Sherwani, "Algorithms for VLSI Physical Design Automation", Kluwar AcademicPublishers, 2002.

3 Drechsler,R., Evolutionary Algorithms for VLSI CAD, Kluwer Academic Publishers, Boston, 1998.


14





L T P C CA ES Total

10 PAE 202 ANALOG VLSI CIRCUITS(PAE, PVL) 3 0 0 3 50 50 100

Objective(s) To know about the various analog VLSI circuits, DFT and analog VLSI interconnects.1 ANALOG CIRCUIT BUILDING BLOCKS Total Hrs 9

Switches, active resistors - Current sources and sinks - Current mirrors/amplifiers - Voltage and currentreferences, Comparator, Multiplier.

2 AMPLIFIERS Total Hrs 9MOS and BJT inverting amplifier - Improving performance of inverting amplifier - CMOS and BJT differentialamplifiers - Characterization of Op-Amp - The BJT two stage op-amp - The CMOS two stage op-amp -op-ampswith output stage, Folded Cascode op-amp, Transconductance Amplifier.

3 FILTERS Total Hrs 9Low pass filters - High pass filters – Band Pass filters – Phase Locked Loops.

4 DATA CONVERTER FUNDAMENTALS Total Hrs 9Ideal A/D and D/A converters, Quantization noise, Signed codes, Performance limitations.

5 DESIGN FOR TESTABILITY AND ANALOG VLSIINTERCONNECTS Total Hrs 9

Fault modeling and simulation – Testability- Analysis Technique-Ad Hoc Methods and General Guidelines-ScanTechniques-Boundary Scan-Built-in Self Test Analog Test Buses-Design for Electron-Beam Testability-Physicsof Interconnects in VLSI-Scaling of Interconnects-A Model for Estimating wiring Density-A ConfigurableArchitecture for Prototyping Analog Circuits.Total hours to be taught 45Reference(s) :

1 Randall L. Geiger, Phillip E. Allen, Noel R. Strader, "VLSI Design Techniques for Analog and DigitalCircuits", McGraw Hill, International Edition 1990

2 Mohammed Ismail, Terri Fiez, “ Analog VLSI signal and Information Processing”, McGraw-HillInternational Editions, 1994

3 David A. Johns, Ken Martin, “Analog Integrated Circuit Design” John Wiley & Sons, 2002


15





L T P C CA ES Total

10 PAE 203

ADVANCED COMPUTERARCHITECTURE AND PARALLELPROCESSING(PAE, PVL)

3 0 0 3 50 50 100

Objective(s)To understand the basics of parallel processing and Mechanisms used in parallel processing.To discuss in detail the principle and classification of pipeline processors. To Study thesoftware and parallel programming concepts.

1 THEORY OF PARALLELISM Total Hrs 9Parallel computer models - the state of computing, Multiprocessors and Multicomputer and Multivectors andSIMD computers, PRAM and VLSI models, Architectural development tracks. Program and network properties-Conditions of parallelism.

2 PARTITIONING AND SCHEDULING Total Hrs 9Program partitioning and scheduling, Program flow mechanisms, System interconnect architectures. Principlesof scalable performance - performance matrices and measures, Parallel processing applications, speedupperformance laws, scalability analysis and approaches.

3 HARDWARE TECHNOLOGIES Total Hrs 9Processor and memory hierarchy advanced processor technology, superscalar and vector processors, memoryhierarchy technology, virtual memory technology- Bus cache and Shared Memory - backplane bus systems,cache memory organizations, shared memory organizations, sequential and weak consistency models,Pipelining and superscalar Techniques.

4 PARALLEL AND SCALABLE ARCHITECTURE Total Hrs 9Multiprocessor and Multicomputer, Multivector and SIMD computers, Scalable, Multithreaded and data flowarchitectures.

5 SOFTWARE AND PARALLEL PROGRAMMING Total Hrs 9Parallel models, Languages and compilers, Parallel program development and environments, UNIX, MACHand OSF/1 for parallel computersTotal hours to be taught 45Reference(s) :

1 Kai Hwang, “Advanced Computer Architecture ", McGraw Hill International, 2001.

2 Dezso Sima, Terence Fountain, Peter Kacsuk,”Advanced Computer architecture – A Design SpaceApproach”, Pearson Education, 2003.

3 John P.Shen, “Modern processor design. Fundamentals of super scalar processors”, Tata McGraw Hill2003.


16


Department Electronics andCommunication Engineering Programme Code & Name PAE : M.E. Applied



L T P C CA ES Total

10 PAE 204 ADVANCED DIGITAL SIGNALPROCESSING 3 1 0 4 50 50 100

Objective(s) To learn spectrum estimation, linear estimation, prediction and adaptive filtering concepts.1 DISCRETE RANDOM SIGNAL PROCESSING Total Hrs 12

Random processes –Ensemble Averages, Gaussian Processes-Stationary Process- Auto covariance and autocorrelation matrices, Ergodicity – White noise - Power spectrum – Wiener khintchine Theorem - Filteringrandom processes – Spectral factorization – Special type of random processes.

2 SPECTRUM ESTIMATION (ADSP) Total Hrs 12Parameter estimation: Bias and consistency Nonparametric methods-The Periodogram- Performance of thePeriodogram – Modified periodogram -Bartlett’s Method: Welch’s Method – Blackman – Tukey method –Performance comparisons. Parametric methods- Auto regressive spectrum estimation- Autocorrelation Mehtod– Moving Average Spectrum estimation – Auto regressive moving Average Spectrum estimation.

3 LINEAR PREDICTION Total Hrs 12Forward and backward predictions, Solution of the normal equations – Levinson- Durbin algorithms. Leastmean squared error criterion – FIR Wiener filter and Wiener IIR filters – Wiener filter for filtering and prediction.

4 ADAPTIVE FILTER Total Hrs 12Concepts of adaptive filter – FIR adaptive filters – LMS adaptive algorithm – Adaptive recursive filters–Adaptive noise and echo cancellation – AR lattice and ARMA lattice – ladder filter.

5 MULTIRATE SYSTEM Total Hrs 12Basic multirate operations – Decimation and Interpolation - Interconnection of Building blocks – Nobleidentities- Polyphase representation- efficient structures for Decimation and interpolation fillers - Multistageimplementation - Applications of multirate system–Digital audio system-Subband coding of speech and imagesignals- Quadrature mirror filter.Total hours to be taught 60Reference(s) :

1 Monson H.Hayes, “Statistical Digital Signal Processing and Modeling”, Wiley, 2002.

2 John G. Proakis, Dimitris G.Manolakis, “Digital Signal Processing: Principles Algorithms andApplications” PHI, 12th Indian reprint, 2001.

3 S.K. Mitra, “Digital Signal Processing – A computer based approach”, Tata McGraw Hill, New Delhi,2001.

4 P.PVaidyanathan “Multirate Systems and Filter Banks”, Pearson Education, 1993


17

K.S.Rangasamy College of Technology Autonomous Regulation R 2010

Department Electronics andCommunication Engineering

Programme Code &Name PAE : M.E. Applied Electronics

Semester II

Course Code Course NameHours/Week Credit Maximum Marks

L T P C CA ES Total

10 PAE 205 ELECTRONICS SYSTEM DESIGNLABORATORY 0 0 3 2 50 50 100

Objective(s) To teach designing, simulation and implementation of VLSI circuits & filters using SPICE, DSP,CCS & MATLAB.

List of Experiments

1. Design and Simulation of NMOS and CMOS Logic Gates using SPICE.2. Design and Simulation of CMOS Memory Cell using SPICE.3. Design and Implementation of Convolution algorithm using DSP.4. Implementation of Adaptive Filters using DSP.5. Implementation of multirate sampling system using CCS.6. Periodogram Estimation.7. Adaptive Filter Implementation.8. Time frequency domain properties of different windows using MATLAB.9. Design of FIR filters using windowing Technique.

10. IIR filter design using CCS.


18




Course Code Course NameHours / Week Credit Maximum Marks

L T P C CA ES Total

10 PAE 206TECHNICAL REPORTPREPARATION ANDPRESENTATION

0 0 2 0 100 00 100

Objective(s)To provide exposure to the students to refer, read and review the research articles in referredjournals and conference proceedings.To Improve the technical report writing and presentation skills of the students.

Methodology • Each student is allotted to a faculty of the department by the HOD• By mutual discussions, the faculty guide will assign a topic in the general / subject area

to the student.• The students have to refer the Journals and Conference proceedings and collect the

published literature.• The student is expected to collect atleast 20 such Research Papers published in the

last 5 years.• Using OHP/Power Point, the student has to make presentation for 15-20 minutes

followed by 10 minutes discussion.• The student has make two presentations, one at the middle and the other near the end

of the semester.• The student has to write a Technical Report for about 30-50 pages (Title page, One

page Abstract, Review of Research paper under various subheadings, ConcludingRemarks and List of References). The technical report has to be submitted to the HODone week before the final presentation, after the approval of the faculty guide.

Execution

Week ActivityI Allotment of Faculty Guide by the HoDII Finalizing the topic with the approval of Faculty Guide

III-IV Collection of Technical papersV-VI Mid semester presentation

VII-VIII Report writingIX Report submission

X-XI Final presentation

Evaluation

100% by Continuous Assessment 2 Hrs/week

Component WeightageMid semester presentation 25%Final presentation (Internal) 25%End Semester Examination Report 30%Presentation 20%

Total 100%


19



ElectronicsSemester III


L T P C CA ES Total

10 PAE 301 ARM ARCHITECTURE ANDPROGRAMMING(PAE,PVL) 3 0 0 3 50 50 100

Objective(s) To introduce the architecture and programming of ARM processor. To introduce the CPU coreof ARM processors and its applications

1 ARM ARCHITECTURE Total Hrs 9RISC machine-ARM programmer’s model-Development tools-ARM assembly language programming- ARMorganization-ARM instruction execution-ARM implementation-ARM coprocessor interface

2 ARM INSTRUCTION SET Total Hrs 9ARM instruction set. Floating point architecture-Expressions-Conditional statements- loops-Functions andprocedures-Use of memory- Run time environment

3 THUMB INSTRUCTION SET Total Hrs 9Thumb instruction set-Thumb programmer’s model-Thumb branch instruction-Thumb data processinginstruction-data transfer instruction-implementation.ARM memory interface-Advanced Microcontroller BusArchitecture (AMBA)-ARMulator -JTAG boundary scan test architecture-ARM Debug architecture. Embeddedtrace.

4 ARM PROCESSOR CORE Total Hrs 9Memory hierarchy-Architectural support for operating systems-Memory size and speed-Cache memorymanagement-Operating systems-ARM processor chips.ARM7TDMI-ARM8-ARM9TDMI-ARM10TDMI

5 EMBEDDED ARM APPLICATIONS Total Hrs 9ARM MMU architecture-The ARM710T.ARM740T.ARM810.The ARM920T and ARM940T-The ARM946E-Sand ARM966E-S.ARM1020E-The VLSI ISDN Subscriber Processor. The Ericsson-VLSI Bluetooth BasebandController-The ARM7500-The ARM7100Total hours to be taught 45Reference(s) :

1 S.Furber, ARM System-on-Chip Architecture, Pearson –Third Impression,2010

2 ARM System Developer’s Guide, Designing and optimizing Systems Software: Andrew N. Sloss, D.Symes, C.Wright, Elsevier Reprinted 2010.

3 ARM Architecture Reference Manual, 2nd Ed, Published 2001, edited by David Seal, Addison-Wesley

4 Wayne Wolf, Computers as Components: Principles of Embedded Computing System Design, MorganKaufman Publishers, 2001.


20



ElectronicsSemester III


L T P C CA ES Total

10 PAE 302 PROJECT WORK – PHASE I 0 0 12 2 100 00 100

Objective (s)To impart the practical knowledge to the students and also to make them to carry out thetechnical procedures in their project work. To provide an exposure to the students to refer,read and review the research articles, journals and conference proceedings relevant to theirproject work and placing this as their beginning stage for their final presentation.

Methodology

• Three reviews have to be conducted by the committee of minimum of three members

one of which should be the guide

• Problem should be selected

• Students have to collect about 20 papers related to their work.

• Report has to be prepared by the students as per the format

• Preliminary implementation can be done if possible

• Internal evaluation has to be done for 100 marks


21



ElectronicsSemester IV

Course CodeCourse Name

Hours/ Week Credit Maximum Marks

L T P C CA ES Total

10 PAE 401 PROJECT WORK – PHASE II 0 0 40 10 50 50 100

Objective (s)This enables and strengthens the students to carry out the project on their own and toimplement their innovative ideas to forefront the risk issues and to retrieve the hazards byadopting suitable assessment methodologies and stating it to global.

Methodology

• Three reviews have to be conducted by the committee of minimum of three members

one of which should be the guide

• Each review has to be evaluated for 100 marks.

• Attendance is compulsory for all reviews. If a student fails to attend review for some

valid reason, one or more chance may be given.

• They should publish the paper preferably in the journals/conferences.

• Final review will be done by the committee that consists of minimum of three

members one of which should be the guide (including one external expert examiner)

• The report should be submitted by the students around at the end of May.


22



ElectronicsELECTIVE


L T P C CA ES Total10 PAE E01 NANO ELECTRONICS 3 0 0 3 50 50 100

Objective(s) To understand the concept about Nano structures, logic devices and data transmission,interfaces and displays.

1 TECHNOLOGY AND ANALYSIS Total Hrs 9Film Deposition Methods – Lithography – Material removing techniques – Etching and Chemical – MechanicalPolishing – Scanning Probe Techniques.

2 CARBON NANO STRUCTURES Total Hrs 9Carbon Clusters – Carbon Nano tubes – Fabrication – Electrical, Mechanical and Vibrational Properties-Applications of Carbon Nano tubes.

3 LOGIC DEVICES Total Hrs 9Silicon MOSFET’s – Novel materials and alternative concepts - Ferroelectric Field Effect Transistors – Superconductor digital electronics – Carbon Nano tubes for data processing.

4 RANDOM ACCESS MEMORIES AND MASS STORAGEDEVICES Total Hrs 9

High Permittivity materials for DRAM’s – Ferro electric Random Access Memories - Magneto-resistive RAM.Hard Disk Drives – Magneto Optical Disks – Rewritable DVDs based on Phase Change Materials –Holographic Data Storage.

5 DATA TRANSMISSION AND INTERFACES AND DISPLAYS Total Hrs 9Photonic Networks – Microwave Communication Systems. Liquid Crystal Displays – Organic Light emittingDevices.Total hours to be taught 45Reference(s) :

1 Rainer Waser ,“Nano Electronics and Information Technology “, Wiley VCH – Feb 20052 Charles Poole ,’Introduction to Nano Technology” Wiley Interscience – May 2003


23





ELECTIVE


L T P C CA ES Total

10 PAE E02 NEURAL NETWORKS AND ITSAPPLICATIONS 3 0 0 3 50 50 100

Objective(s) To learn the architecture, training and applications of different neural networks.1 INTRODUCTION TO ARTIFICIAL NEURAL NETWORKS Total Hrs 9

Neuro-physiology- General Processing Element – ADALINE – LMS learning rule – MADALINE – MR2 trainingalgorithm.

2 BPN AND BAM Total Hrs 9Back Propagation Network – update of output and hidden layer weights – application of BPN – associativememory – Bi-Associative Memory – Hopfield memory – traveling sales man problem.

3 SIMULATED ANNEALING AND CPN Total Hrs 9Annealing, Boltzmann machine – learning – application – Counter Propagation Network – architecture –training - Applications

4 SOM AND ART Total Hrs 9Self organizing map- learning algorithm – feature map classifier – applications – architecture of AdaptiveResonance Theory – pattern matching in ART network.

5 NEOCOGNITRON Total Hrs 9Architecture of Neocognitron – Data processing and performance of Neocognitron - Architecture of spatio –temporal networks for speech recognition.Total hours to be taught 45Reference(s) :

1 J.A. Freeman and B.M.Skapura, “Neural Networks, Algorithms Applications and ProgrammingTechniques”, Pearson Education, 2004.

2 Laurene Fausett, “Fundamentals of Neural Networks: Architecture, Algorithms and Application”,Pearson Education, 2009.


24



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E03 SEMICONDUCTOR MEMORYDESIGN AND TESTING 3 0 0 3 50 50 100

Objective(s) To learn the technologies for designing semiconductor memories, methods of testingsemiconductor memories and the techniques involved in packaging of memories

1 RANDOM ACCESS MEMORY TECHNOLOGIES Total Hrs 9Static Random Access Memories (SRAM): SRAM cell structures, MOS SRAM Architecture, MOS SRAM celland peripheral Circuit Operation, Bipolar SRAM Technologies, Silicon on insulator (SOI) Technology. AdvancedSRAM Architectures and Technologies, Application Specific SRAMs. Dynamic Random Access Memories(DRAM): DRAM Technology Development, CMOS DRAM, DRAM cell theory and advanced cell structures,BiCMOS DRAM, soft error failures in DRAM, Advanced DRAM Design and Architecture, Application SpecificDRAM

2 NON-VOLATILE MEMORIES Total Hrs 9Masked Read only Memories (ROM), High Density ROMs, Programmable ROM, Bipolar ROMs, CMOSPROMs, Erasable(UV) Programmable ROM(EPROM), Floating, Gate EPROM Cell, One time ProgrammableEPROM (OTPEPROM), Electrically Erasable PROMS, EEPROM Technology and Architecture, Non volatileSRAM, Flash Memories (EPROM or EEPROM), Advanced Flash Memory Architecture.

3 MEMORY FAULT MODELLING TESTING AND MEMORYDESIGN FOR TESTABILITY AND FAULT TOLERANCE Total Hrs 9

RAM Fault Modeling, Electrical Testing, Peusdo Random Testing-Megabit DRAM Testing-Nonvolatile MemoryModeling and Testing-IDDQ Fault Modeling and Testing-Application Specific Memory Testing. Ram FAULTModelling, BIST Techniques for Memory.

4 SEMICONDUCTOR MEMORY RELIABILITY ANDRADIATION EFFECTS Total Hrs 9

General Reliability Issues-RAM Failure Modes and Mechanism-Nonvolatile Memory Reliability-ReliabilityModeling and Failure Rate Prediction-Design for Reliability-Reliability Test Structures-Reliability Screening andQualification. Radiation Effects-Single Event Phenomenon (SEP)-Radiation Hardening Techniques-RadiationHardening Process and Design Issues-Radiation Hardened Memory Characteristics-Radiation HardnessAssurance and Testing - Radiation Dosimetry-Water Level Radiation Testing and Test Structures

5 ADVANCED MEMORY TECHNOLOGIES AND HIGH-DENSITY MEMORY PACKAGING TECHNOLOGIES Total Hrs 9

Ferroelectric Random Access Memories (FRAMs)-Gallium Arsenide (GaAs) FRAMs-Analog Memories-Magnetoresistive Random Access Memories (MRAMs)-Experimental Memory Devices. Memory Hybrids andMCMs (2D)-Memory Stacks and MCMs (3D)-Memory MCM Testing and Reliability Issues-Memory Cards-HighDensity Memory Packaging Future Directions.Total hours to be taught 45Reference(s) :

1 Ashok K.Sharma, " Semiconductor Memories Technology, Testing and Reliability ",Wiley, 2002

2 Ashok K.Sharma, “Advanced Semiconductor Memories – Architecture, Design and Applications ,Wiley,2002


25



ElectronicsELECTIVE


L T P C CA ES Total10 PAE E04 LOW POWER VLSI DESIGN 3 0 0 3 50 50 100

Objective(s)To emphasize the optimization and trade – off techniques that involve power dissipation, andto highlight the basic principles, methodologies and techniques that are common to CMOSdigital design.

1 POWER DISSIPATION IN CMOS Total Hrs 9Hierarchy of limits of power – Sources of power consumption – Physics of power dissipation in CMOS FETdevices- Basic principle of low power design.

2 POWER OPTIMIZATION Total Hrs 9Logical level power optimization – Circuit level low power design – Circuit techniques for reducing powerconsumption in adders and multipliers.

3 DESIGN OF LOW POWER CMOS CIRCUITS Total Hrs 9Computer Arithmetic techniques for low power systems – Reducing power consumption in memories – Lowpower clock, Interconnect and layout design – Advanced techniques – Special techniques.

4 POWER ESTIMATION Total Hrs 9Power estimation techniques – Logic level power estimation – Simulation power analysis – Probabilistic poweranalysis.

5 SYNTHESIS AND SOFTWARE DESIGN FOR LOW POWER Total Hrs 9Synthesis for low power –Behavioral level transforms- Software design for low power.Total hours to be taught 45Reference(s) :

1 K.Roy and S.C. Prasad , LOW POWER CMOS VLSI circuit design, Wiley, 2000.

2 Dimitrios Soudris, Chirstian Pignet, Costas Goutis, DESIGNING CMOS CIRCUITS FOR LOW POWER,Kluwer,2002.

3 B. Kuo and J.H Lou, Low voltage CMOS VLSI Circuits, Wiley 1999.4 Gary K.Yeap, practical Low Power Digital VLSI Design, Kluwer academic publishers.

5 James B. Kuo, Shin – chia Lin, Low voltage SOI CMOS VLSI Devices and Circuits. John Wiley andsons, inc 2001.


26



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E05 COMPUTATIONAL INTELLIGENTTECHNIQUES 3 0 0 3 50 50 100

Objective(s)To understand the basics of Fuzzy logic and its modeling concepts, fundamentals of neuralnetworks and its learning concepts. To learn the basics of genetic algorithm and its optimizationprinciples.

1 FUZZY LOGIC Total Hrs 9Introduction to Neuro – Fuzzy and soft Computing – Fuzzy Sets – Basic Definition and Terminology –Set-theoretic operations – Member Function Formulation and parameterization – Fuzzy Rules and FuzzyReasoning- Extension principle and Fuzzy Relations – Fuzzy If-Then Rules – Fuzzy Reasoning –Fuzzy Inference Systems – Mamdani Fuzzy Models-Sugeno Fuzzy Models – Tsukamoto FuzzyModels – Input Space Partitioning and Fuzzy Modeling.

2 GENETIC ALGORITHM Total Hrs 9Derivative-based Optimization – Descent Methods – The Method of steepest Descent – ClassicalNewton’s Method – Step Size Determination – Derivative-free Optimization – Genetic Algorithms –Simulated Annealing – Random Search – Downhill Simplex Search.

3 NEURAL NETWORKS Total Hrs 9Introduction -Supervised Learning Neural Networks – Perceptrons - Adaline – Back propagation Multilayerperceptrons Radial Basis Function Networks – Unsupervised Learning and Other Neural Networks –Competitive Learning Networks – Kohonen Self – Organizing Networks – Learning Vector Quantization –Hebbian Learning.

4 NEURO FUZZY MODELING Total Hrs 9Adaptive Neuro-Fuzzy Inference Systems – Architecture – Hybrid Learning Algorithm – learning Methods thatCross-fertilize ANFIS and RBFN – Coactive Neuro-Fuzzy Modeling – Framework – Neuron Functions forAdaptive Networks – Neuro Fuzzy Spectrum.

5 APPLICATIONS Total Hrs 9Printed Character Recognition – Inverse Kinematics Problems – Automobile Fuel Efficiency prediction –Soft Computing for Color Recipe Prediction.Total hours to be taught 45

Reference(s) :1 J.S.R.Jang, C.T.Sun and E.Mizutani, “Neuro-Fuzzy and Soft Computing”, PHI, Pearson Education 2004.

2 Davis E.Goldberg,” Genetic Algorithms: Search, Optimization and Machine Learning” AddisonWesley, N.Y., 1989.

3 S.Rajasekaran and G.A.V.Pai,” Neural Networks, Fuzzy Logic and Genetic Algorithms”, PHI,2003.

4 R.Eberhart, P.Simpson and R.Dobbins,” Computational Intelligence” PC Tools”, AP professional,Boston 1996.


27



ElectronicsELECTIVE


10 PAE E06 DSP PROCESSOR ARCHITECTUREAND PROGRAMMING 3 0 0 3 50 50 100

Objective(s) Introduction to DSP Processors, Architecture of TMS320C5X and TMS320C3X Processor. andintroduction of DSP family processors.

1 FUNDAMENTALS OF PROGRAMMEMABLE DSPs Total Hrs 9Multiplier and Multiplier accumulator – Modified Bus Structures and Memory access in P-DSPs – Multipleaccess memory – Multi-port memory – VLIW architecture- Pipelining – Special Addressing modes in P-DSPs –chip Peripherals.

2 TMS320C5X PROCESSOR Total Hrs 9Architecture – Assembly language syntax - Addressing modes – Assembly language Instructions - Pipelinestructure, Operation – Block Diagram of DSP starter kit – Application Programmes for processing real timesignals.

3 TMS320C3X PROCESSOR Total Hrs 9Architecture – Data formats - Addressing modes – Groups of addressing modes- Instruction sets - Operation –Block Diagram of DSP starter kit – Application Programmes for processing real time signals – Generating andfinding the sum of series, Convolution of two sequences, Filter design.

4 ADSP PROCESSORS Total Hrs 9Architecture of ADSP-21XX and ADSP-210XX series of DSP processors- Addressing modes and assemblylanguage instructions – Application Programmes –Filter design, FFT calculation.

5 ADVANCED PROCESSORS Total Hrs 9Architecture of TMS320C54X: Pipe line operation, Code Composer studio - Architecture of TMS320C6X -Architecture of Motorola DSP563XX – Comparison of the features of DSP family processors.Total hours to be taught 45Reference(s) :

1 B.Venkataramani and M.Bhaskar, “Digital Signal Processors – Architecture, Programming andApplications” – Tata McGraw – Hill Publishing Company Limited. New Delhi, 2nd edition,2003

2 User guides Texas Instrumentation, Analog Devices, Motorola.


28



ElectronicsELECTIVE


L T P C CA ES Total10 PAE E07 VLSI SIGNAL PROCESSING 3 0 0 3 50 50 100

Objective(s)To study the transformation for high speed using pipelining, retiring and parallel processingtechniques and experience on power reduction transformation for supply voltage reduction,capacitance reduction. To learn area reduction using folding techniques.

1 INTRODUCTION TO DSP SYSTEMS Total Hrs 9Introduction TO DSP Systems – Typical DSP algorithms: Iteration Bound – data flow graph representations,loop bound and iteration bound, Longest path Matrix algorithm: Pipelining and parallel processing – Pipeliningof FIR digital filters, parallel processing, pipelining and parallel processing for low power.

2 RRRETIMING, FOLDING AND UNFOLDING Total Hrs 9Retiming – definitions and properties Retiming techniques: Unfolding – an algorithm for Unfolding, properties ofunfolding, sample period reduction and parallel processing application: Folding – Folding transformation –Register minimizing techniques.

3 FAST CONVOLUTION Total Hrs 9Fast convolution – Cook-Took algorithm, modified Cook-Took algorithm, Iterated Convolution – CyclicConvolution: Pipelined and parallel recursive and adaptive filters – inefficient/efficient single channelinterleaving, Look – Ahead pipelining in first – order IIR filters, Look-Ahead pipelining and parallel processing ofIIR filters, pipelined adaptive digital filters.

4 BIT-LEVEL ARITHMETIC ARCHITECTURES AND SYSTOLICARCHITECTURE DESIGN Total Hrs 9

BAIT-Level Arithmetic Architectures-parallel multipliers with sign extension, parallel carry-ripple arraymultipliers, parallel carry-save multiplier, 4x 4 bit Baugh-Wooley carry-save multiplication tabular form andimplementation, design of Lyon’s bit-serial multipliers using Horner’s rule, bit-serial FIR filter, CSDrepresentation, CSD multiplication using Horner’s rule for precision improvement, systolic array designmethodology – FIR systolic Arrays – selection of scheduling vector-matrix multiplication and 2D systolic arraydesign-Systolic design for space representations containing Delays.

5 PROGRAMMEMING DIGITAL SIGNAL PROCESSORS Total Hrs 9Synchronous, Wave and asynchronous pipelining – synchronous pipelining and clocking styles, clock skew inedge-trigged single-phase clocking, two-phase clocking, wave pipelining, asynchronous pipelining bundled dataversus dual rail protocol: Programming Digital Signal Processors - general architecture with importantfeatures.Total hours to be taught 45Reference(s) :

1 Keshab K. Parhi, “VLSI Digital Signal Processing Systems Design and Implementation” Wiley -Inter science, 1999

2 Gary Yeap, “Practical Low Power Digital VLSI Design”, Kluwer Academic Publishers, 1998


29



ElectronicsELECTIVE


L T P C CA ES Total10 PAE E08 MEMS SYSTEM DESIGN 3 0 0 3 50 50 100

Objective(s) To study the fundamentals of MEMS systems, Materials for Microsystems, fabrication process,system design and micro sensors

1 INTRODUCTION Total Hrs 9Overview – Mems and micro system products – Microsystems and Microelectronics – Working Principle ofMicrosystems – Micro actuation techniques.

2 MATERIALS FOR MICRO SYSTEMS Total Hrs 9Substrate and wafer – single crystal silicon wafer formation – ideal substrates – Mechanical properties – siliconcompounds – Sio2, SiC, Si3N4 and polycrystalline silicon – Silicon piezo resistors – Gallium arsenide, quartz –Piezoelectric crystals - polymers.

3 MICRO SYSTEM FABRICATION PROCESS Total Hrs 9Photolithography – Ion implantation – Diffusion – oxidation – CVD – physical vapor deposition- Deposition byepitaxy – etching process

4 Micro system Design Total Hrs 9Design considerations- Process design- mask layout design – Design constraints – Selection of Materials –Manufacturing Process, Signal transduction – packaging – Application of Micro system in automotive industry– Biomedical – Aerospace - telecommunication

5 MICRO SENSORS Total Hrs 9Introduction – Microsensors – Biomedical sensors – Pressure sensors – Thermal Sensors – Chemical sensors– Optical sensors – Microactuatioan – Mems with actuators.Total hours to be taught 45Reference(s) :

1 Tai-Ran Hus, MEMS & Microsystems Design and Manufacture, Tata McGraw-Hill, 2006.2 Mohamed Gad-el-Hak, The MEMS Hand book, CRC press 2002.

3 Julian W.Gardner, Vijay K.Varadan, Osama O.Awadel Karim, Microsensors MEMS and Smart Devices,John Wiby &sons Ltd.,2001.

4 S.Fatikow, U.Rembold, Microsystem Technology and Microrobotics, Springer-Verlag Berlin Heideiberg,1997.


30



ElectronicsELECTIVE


L T P C CA ES Total10 PAE E09 SYSTEM ON CHIP 3 0 0 3 50 50 100

Objective(s) To understand the concepts of basic arm processor architecture. To emphasis the knowledgeabout programming of languages and operating system of ARM based system development

1 INTRODUCTION TO PROCESSOR DESIGN, ARMARCHITECTURE Total Hrs 9

Abstraction in hardware design- MUO – a simple processor – Processor Design trade off- Design for low powerconsumption, Acorn RISC Machine – Architecture Inheritance – ARM Programming Model- ARM DevelopmentTools – 3 and 5 Stage Pipeline ARM Organization - ARM Instruction Execution and Implementation – ARM Co-Processor Interface

2 ARM ASEEMBLY LANGUAGE PROGRAMMING Total Hrs 9ARM Instruction Types – Data Transfer, Data Processing and Control Flow Instructions - ARM Instruction Set –Co-Processor Instructions.

3 ARCHITECTURAL SUPPORT FOR HIGH LEVELLANGAUGE, MEMORY HIERARCHY Total Hrs 9

Data Types – Abstraction in software Design – Expressions – Loops – Functions and Procedures – ConditionalStatements – Use of Memory, Memory Size and Speed – On Chip Memory – Caches – Cache Design – anExample- Memory management

4 ARCHITECTURAL SUPPORT FOR SYSTEMDEVELOPMENT Total Hrs 9

Advanced Microcontroller Bus Architecture – ARM Memory Interface – ARM Reference Peripheral Specification– Hardware System Prototyping Tools – Armulator – Debug Architecture.

5 ARCHITECTURAL SUPPORT FOR OPERTAING SYSTEM Total Hrs 9An Introduction to Operating Systems – ARM System Control Coprocessor- CP15 Protection Unit Registers –ARM Protection Unit – CP15 MMU Registers – ARM MMU Architecture – Synchronization –Context SwitchingInput and Output.Total hours to be taught 45Text book

1 Steve Furber, “ARM System on Chip Architecture” Addison- Wesley Professional 2nd Edition, Aug 2000Reference(s) :

2 Ricardo Reis “Design of System on a Chip: Devices and Components” Springer 1st Edition, July 2004

3 Jason Andrews “Co-Verification of Hardware and Software for ARM System on Chip Design (EmbeddedTechnology)” Newnes, BK and CD-ROM, Aug 2004.


31



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E10 PHYSICAL DESIGN OF VLSICIRCUITS 3 0 0 3 50 50 100

Objective(s) To learn the standard algorithms for VLSI physical design automation, to learn placementand routing algorithms. To learn floor planning algorithms.

1 INTRODUCTION TO VLSI TECHNOLOGY Total Hrs 9Layout Rules-Circuit abstraction Cell generation using Programme able logic array transistor chaining, WeinBerger arrays and gate matrices-layout of standard cells gate arrays and sea of gates, field Programme ablegate array(FPGA)-layout methodologies-Packaging-Computational Complexity-Algorithmic Paradigms

2 PLACEMENT USING TOP-DOWN APPROACH Total Hrs 9Partitioning: Approximation of Hyper Graphs with Graphs, Kernighan-Lin Heuristic- Ratiocut- partition withcapacity and i/o constrants. Floor planning: Rectangular dual floor planning- hierarchial approach- simulatedannealing- Floor plan sizing-Placement: Cost function- force directed method- placement by simulatedannealing- partitioning placement- module placement on a resistive network – regular placement- linearplacement.

3 ROUTING USING TOP DOWN APPROACH Total Hrs 9Fundamentals: Maze Running- line searching- Steiner trees Global Routing: Sequential Approaches-hierarchial approaches- multicommodity flow based techniques- Randomised Routing- One Step approach-Integer Linear Programming Detailed Routing: Channel Routing- Switch box routing. Routing in FPGA: Arraybased FPGA- Row based FPGAs

4 PERFORMANCE ISSUES IN CIRCUIT LAYOUT Total Hrs 9Delay Models: Gate Delay Models- Models for interconnected Delay- Delay in RC trees. Timing – DrivenPlacement: Zero Stack Algorithm- Weight based placement- Linear Programming Approach Timing DrivingRouting: Delay Minimization- Click Skew Problem- Buffered Clock Trees. Minimization: constrained viaMinimization- unconstrained via Minimization- Other issues in minimization

5 SINGLE LAYER ROUTING, CELL GENERATION ANDCOMPACTION Total Hrs 9

Planar subset problem (PSP) - Single layer global routing- Single Layer Global Routing- Single Layer detailedRouting- Wire length and bend minimization technique – Over The Cell (OTC) Routing- Multiple chip modules(MCM) – Programmable Logic Arrays- Transistor chaining- Wein Burger Arrays- Gate matrix layout- 1Dcompaction- 2D compaction.Total hours to be taught 45Reference(s) :

1 Sarafzadeh, C.K. Wong, “An Introduction to VLSI Physical Design”, Mc Graw Hill International Edition1995

2 Preas M. Lorenzatti, “Physical Design and Automation of VLSI systems”, The Benjamin CumminsPublishers, 1998.

3 Naveed A. Sherwani “Algorithm for VLSI Physical Design Automation”, 3rd Edition, Springer, 1998.

4 Sadiq M. Sait, Habib Youssef “VLSI Physical Design Automation, Theory and Practice” WorldScientific Publishing Company, 1st Edition,1999.


32



ElectronicsELECTIVE


L T P C CA ES Total10 PAE E11 DIGITAL IMAGE PROCESSING 3 0 0 3 50 50 100

Objective(s) To study the image fundamentals, mathematical transforms necessary for image Processingand Image Processing techniques

1 DIGITAL IMAGE FUNDAMENTALS AND TRANSFORMS Total Hrs 9Elements of visual perception – Image sampling and quantization Basic relationship between pixels – Basicgeometric transformations-Introduction to Fourier Transform and DFT – Properties of 2D Fourier Transform –FFT – Separable Image Transforms -Walsh – Hadamard – Discrete Cosine Transform, Haar, Slant – Karhunen– Loeve transforms.

2 IMAGE ENHANCEMENT AND RESTORATION Total Hrs 9Basic gray level transformations – Histogram equalization – Histogram matching -spatial filtering – smoothingspatial filters – sharpening spatial filters- model of the image degradation / Restoration process- mean filters –order – statistics filters- Adaptive filters – Inverse filtering – minimum mean square error filtering – constrainedleast squares filtering – Geometric mean filter – geometric transformations.

3 IMAGE SEGMENTATION AND RECOGNITION Total Hrs 9Detection of Discontinuities – Edge linking and boundary detection – Region based segmentation –morphological operators: Dilation, erosion, opening and closing. Image recognition patterns and patternclasses. Recognition based on decision – theoretic methods.

4 COLOR IMAGE PROCESSING & IMAGE COMPRESSION Total Hrs 9Color Fundamentals – Color Models – Pseudo color Image Processing –Basics of Full-Color Image Processing– Color Transformations – Smoothing and Sharpening – Image Segmentation Based on Color – Noise in ColorImages – Image compression Models – Color Image Compression

5 WAVELETS AND MULTIRESOLUTION PROCESSING Total Hrs 9Background – Multiresolution Expansions – Wavelet Transforms in one Dimension – The Fast WaveletTransform – Wavelet Transforms in Two Dimensions – Wavelet PacketsTotal hours to be taught 45Reference(s) :

1 Gonzalez Rafel C, Woods Richard E, "Digital Image Processing", third edition. Prentice Hall, 2006.2 Jain Anil K , "Fundamentals of Digital Image Processing-" , Prentice Hall of India, 2003.

3 Rafael C. Gonzalez Richard E. Woods, Steven Eddins,” Digital Image Processing using MATLAB”,Pearson Education, Inc., 2004.


33



Programme Code& Name


ELECTIVE


10 PAE E12 HIGH PERFORMANCECOMMUNICATION NETWORK 3 0 0 3 50 50 100

Objective(s) To know about the concept of packet switched network ,ISDN, ATM, and Blue toothtechnology.

1 PACKET SWITCHED NETWORKS Total Hrs 9OSI and IP models, Ethernet (IEEE 802.3), Token ring (IEEE 802.5), Wireless LAN (IEEE 802.11) FDDI,DQDB, SMDS: Internetworking with SMDS

2 ISDN AND BROADBAND ISDN Total Hrs 9ISDN - overview, interfaces and functions, Layers and services - Signaling System 7 - Broadband ISDNarchitecture and Protocols.

3 ATM AND FRAME RELAY Total Hrs 9ATM: Main features-addressing, signaling and routing, ATM header structure-adaptation layer, management andControl, ATM switching and transmission.

Frame Relay: Protocols and services, Congestion control, Internetworking with ATM, Internet and ATM, Framerelay via ATM.

4 ADVANCED NETWORK ARCHITECTURE Total Hrs 9IP forwarding architectures overlay model, Multi Protocol Label Switching (MPLS), integrated services in theInternet, Resource Reservation Protocol (RSVP), Differentiated services

5 BLUE TOOTH TECHNOLOGY Total Hrs 9The Blue tooth module-Protocol stack Part I: Antennas, Radio interface, Base band, The Link controller, Audio,The Link Manager, The Host controller interface; The Blue tooth module-Protocol stack Part I: Logical linkcontrol and adaptation protocol, RFCOMM, Service discovery protocol, Wireless access protocol, Telephonycontrol protocol.Total hours to be taught 45Reference(s) :

1 William Stallings,”ISDN and Broadband ISDN with Frame Relay and ATM”, 4th edition, Pearsoneducation Asia, 2002.

2 Leon Gracia, Widjaja, “Communication networks ", Tata McGraw-Hill, New Delhi, 2000.3 Jennifer Bray and Charles F.Sturman,”Blue Tooth” Pearson education Asia, 2001.4 Sumit Kasera, Pankaj Sethi, “ATM Networks ", Tata McGraw-Hill, New Delhi, 2000.

5 Rainer Handel, Manfred N.Huber, Stefan Schroder,”ATM Networks”,3rd edition, Pearson education asia,2002.

6 Jean Walrand and Pravin varaiya, “High Performance Communication networks”, 2nd edition, Harcourtand Morgan Kauffman, London 2000.


34



ElectronicsELECTIVE


L T P C CA ES Total10 PAE E13 LINEAR ALGEBRA 3 0 0 3 50 50 100

Objective(s) To study linear equations, vector spaces, linear transformations, canonical forms, innerproduct spaces, symmetric matrices and applications of linear algebra

1 LINEAR EQUATIONS AND VECTOR SPACES Total Hrs 11Linear equations: Fields; system of linear equations, and its solution sets; elementary row operationsand echelon forms; matrix operations; invertible matrices, LU-factorizationVector Spaces: Vector spaces; subspaces; bases and dimension; coordinates; summary of row-equivalence; computations concerning subspaces

2 LINEAR TRANSFORMATIONS Total Hrs 8Linear Transformations: Linear transformations; algebra of linear transformations; isomorphism; representationof transformations by matrices; linear functionals; transpose of a linear transformation

3 CANONICAL FORMS Total Hrs 8Canonical Forms: Characteristic values; annihilating polynomials; invariant subspaces; direct-sum decompositions; invariant direct sums; primary decomposition theorem; cyclic bases; Jordan canonicalform. Iterative estimates of characteristic values

4 INNER PRODUCT SPACES Total Hrs 9Inner Product Spaces: Inner products; inner product spaces; orthogonal sets and projections; Gram-Schmidt process; QR-factorization; least-squares problems; unitary operators

5 SYMMETRIC MATRICES AND APPLICATIONS OF LINEARALGEBRA Total Hrs 9

Symmetric Matrices and Quadratic Forms: Digitalization; quadratic forms; constrained optimization; singularvalue decompositionApplications of Linear Algebra in DSP, Image Processing, Digital CommunicationTotal hours to be taught 45Reference(s) :

1 Gilbert Strang, "Linear Algebra and its Applications," 4th edition, Thomson Learning Asia, 20082 David C. Lay, “Linear Algebra and its Applications”,4th edition, Pearson Education (Asia) Pte. Ltd, 2009.

3 Bernard Kolman and David R. Hill, "Introductory Linear Algebra with Applications," Pearson Education(Asia) Pte. Ltd, 8th edition, 2009


35



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E14 INDUSTRIAL AUTOMATIONAND CONTROL 3 0 0 3 50 50 100

Objective(s) To know about the basics of PLC, DCS, SCADA and applications of PLC and DCS.1 INTRODUCTION Total Hrs 9

Introduction to automation tools PLC, DCS, SCADA, Hybrid DCS/PLC.2 DCS Total Hrs 9

Introduction to architecture of different makes, DCS Specifications, configuration of DCS blocks for differentapplications, Interfacing of protocol based sensors, actuators and PLC systems, Plant wide databasemanagement, Security and user access management, MES, ERP interface.

3 PROGRAMMABLE LOGIC CONTROLLERS Total Hrs 9Introduction of Advanced PLC programming, Selection of processor, Input/output modules, Interfacing ofInput/output devices, Operator Interface, OPC, study of SCADA software, Interfacing of PLC with SCADAsoftware.

4 DCS PROJECT Total Hrs 9Development of User Requirement Specifications, Functional Design Specifications for automation tool, GAMP,FDA.

5 APPLICATION Total Hrs 9Simple Material Handling Application-Automatic Control Of Ware House Door-Automatic Lubricating OilSupplier-Conveyer Belt motor Control-Automatic Car Washing Machine-Bottle Level Detection Process ControlApplication.Total hours to be taught 45Reference(s) :

1 Frank.D.Petrozella “programmable logic Controller”, 4th Edition, Career Education ,20102 Webb & Reis, ‘Programmable logic controllers’,5th edition , Prentice Hall of India, 20023 Jose A.Romagnoli, Ahmet palazoglu, Introduction to process control , 1st edition CRC press, 20054 Statistical Process Control – ISA Handbook


36



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E15SYNTHESIS ANDOPTIMIZATION OF DIGITALCIRCUITS

3 0 0 3 50 50 100

Objective(s)To Study Microelectronic circuit synthesis and Mapping in detail. To study optimizationtechnique used in system level and circuit level. To study the scheduling algorithm used inmodern logic system design.

1 CIRCUITS AND HARDWARE MODELING Total Hrs 9Design of Microelectronic Circuits - Computer Aided Synthesis and optimization Graph - Optimization problemsand algorithms-Combinatorial optimization-Boolean Algebra and Application-Hardware Modeling Languages –Compilation and Behavioral optimization.

2 ARCHITECTURAL LEVEL SYNTHESIS ANDOPTIMIZATION Total Hrs 9

Circuit specification for Architectural synthesis -Fundamental Architectural synthesis Problems-Area andperformance Estimation-Control unit synthesis-synthesis of pipelined circuits.

3 SCHEDULING ALGORITHMS AND RESOURCE SHARING Total Hrs 9Unconstrained Scheduling-ASAP Algorithm-ALAP Scheduling Algorithm- Scheduling with ResourceConstraints- Scheduling pipelined circuits-Sharing and binding for Dominated circuits-Area Binding-ConcurrentBinding –Module selection problems-Structural testability.

4 LOGIC-LEVEL SYNTHESIS AND OPTIMIZATION Total Hrs 9Logic optimization Principles-Algorithms and logic Minimization –Encoding problems- Multiple-level optimizationof logic networks-Algebraic and Boolean model-Algorithm for delay Evaluation-Rule based logic optimization.

5 CELL-LIBRARY BINDING AND STATE OF ART INSYNTNESSIS Total Hrs 9

Specific problem and algorithm for library Binding – Structural matching - Boolean matching- concurrent logicoptimization and library Binding - production level synthesis systems, Research synthesis systems - Systemlevel synthesis, Hardware software co-design.Total hours to be taught 45Reference(s) :

1 Giovanni De Micheli, “Synthesis and optimization of Digital Circuits”, Tata McGraw-Hill, 2003.2 John Paul Shen, Mikko H. Lipasti, “Modern processor Design”, Tata McGraw Hill, 2003


37



ElectronicsELECTIVE


10 PAE E16 MEDICAL IMAGING TECHNIQUES 3 0 0 3 50 50 100

Objective(s) To learn the concept of MRI, ultrasound imaging, segmentation techniques and 3Dvisualization.

1 INTRODUCTION Total Hrs 9Introduction to imaging modalities-Image quality X-rays in Diagnostic imaging-X-ray production-X-rayinteractions-X-ray spectra-X-ray dosimetry-X-ray detection-radiography-mammography-fluoroscopy. Computedtomography systems- Scanner design-reconstruction techniques-image quality artifacts-multislice imaging-scanner performance..

2 MAGNETIC RESONANCE IMAGING Total Hrs 9Basic principles of nuclear magnetic resonance-Image creation- Slice selection, Frequency encoding, PhaseEncoding, pulse sequence, Image characteristics and artifacts, Hardware and software components

3 ULTRASOUND IMAGING Total Hrs 9The wave equation-Impedance, Power and reflection-Acoustic properties of Biological tissues-Transducers,beam patterns and resolution-Diagnostic imaging modes –Doppler principles.

4 SEGMENTATION Total Hrs 9Image preprocessing-Thersholding-Edge based techniques-Region based segmentation-Classification-deformable models-Image Registration-Geometrical Transformations-Point based methods-Surface basedmethods-Intensity based methods.

5 3D VISUALIZATION Total Hrs 9Pre processing-Scene-based visualization-object based visualization-Manipulation. Medical Applications andSystems– Diagnostics-Therapeutics- Interventions.Total hours to be taught 45Reference(s) :

1 Isaac Bankman, I. N. Bankman , “Handbook of Medical Imaging: Processing and Analysis”, AcademicPress,2000

2 Avinash C.Kak, Malcolm Slaney, “Principles of Computerized Tomographic Imaging”,society of industrialand applied mathemetics,2001.

3 Albert Macowski, “Medical Imaging Systems”, Prentice Hall, New Jersy-1983.


38



ElectronicsELECTIVE


L T P C CA ES Total10 PAE E17 ASIC DESIGN 3 0 0 3 50 50 100

Objective(s) To learn the internal architecture ,types and construction of ASICs

1 INTRODUCTION TO ASICS, CMOS LOGIC AND ASICLIBRARY DESIGN Total Hrs 9

Types of ASICs - Design flow - CMOS transistors - CMOS Design rules - Combinational Logic Cell – Sequentiallogic cell - Data path logic cell - Transistors as Resistors - Transistor Parasitic Capacitance- Logical effort –Library cell design - Library architecture.

2 PROGRAMMABLE ASICS, PROGRAMMABLE ASIC LOGICCELLS AND PROGRAMMABLE ASIC I/O CELLS Total Hrs 9

Anti fuse - Static RAM - EPROM and EEPROM technology - PREP benchmarks - Actel ACT - Xilinx LCA –Altera FLEX - Altera MAX DC & AC inputs and outputs - Clock & Power inputs - Xilinx I/O blocks.

3PROGRAMMABLE ASIC INTERCONNECT,PROGRAMMABLE ASIC DESIGN SOFTWARE AND LOWLEVEL DESIGN ENTRY

Total Hrs 9

Actel ACT -Xilinx LCA - Xilinx EPLD – Altera MAX 5000 and 7000 - Altera MAX 9000 - Altera FLEX –Design systems - Logic Synthesis - Half gate ASIC -Schematic entry - Low level design language - PLA tools-EDIF- CFI design representation.

4 LOGIC SYNTHESIS, SIMULATION AND TESTING Total Hrs 9Verilog and logic synthesis -VHDL and logic synthesis - Types of simulation -Boundary scan test - Faultsimulation - Automatic test pattern generation.

5 ASIC CONSTRUCTION, FLOOR PLANNING, PLACEMENTAND ROUTING Total Hrs 9

System partition - FPGA partitioning - Partitioning methods - Floor planning - Placement - Physical design flow– Global routing - Detailed routing - Special routing - Circuit extraction - DRC.Total hours to be taught 45Reference(s) :

1 M.J.S .Smith, "Application Specific Integrated Circuits, Pearson Education, 2010.

2 Farzad Nekoogar and Faranak Nekoogar, From ASICs to SOCs: A Practical Approach, Prentice HallPTR, 2003.

3 Wayne Wolf, FPGA-Based System Design, Prentice Hall PTR, 2004.


39



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E18 DIGITAL SIGNAL PROCESSINGINTEGRATED CIRCUITS 3 0 0 3 50 50 100

Objective(s) To study DSP system design & CMOS technologies and study DFT & FFT computation and tointroduce the architecture of synthesis of DSP.

1 DSP INTEGARTED CIRCUITS AND VLSI CIRCUITTECHNOLOGIES Total Hrs 9

Standard digital signal processors, Application specific IC’s for DSP, DSP systems, DSP system design,Integrated circuit design. MOS transistors, MOS logic, VLSI process technologies, Trends in CMOStechnologies.

2 DIGITAL SIGNAL PROCESSING Total Hrs 9Digital signal processing, Sampling of analog signals, Selection of sample frequency, Signal-processing systems, Frequency response, Transfer functions, Signal flow graphs, Filter structures, AdaptiveDSP algorithms, DFT-The Discrete Fourier Transform, FFT-The Fast Fourier Transform Algorithm, Imagecoding, Discrete cosine transforms.

3 DIGITAL FILTERS AND FINITE WORD LENGTH EFFECTS Total Hrs 9FIR filters, FIR filter structures, FIR chips, IIR filters, Specifications of IIR filters, Mapping of analog transferfunctions, Mapping of analog filter structures, Multirate systems, Interpolation with an integer factor L, Samplingrate change with a ratio L/M, Multirate filters. Finite word length effects -Parasitic oscillations, Scaling of signallevels, Round-off noise, Measuring round-off noise, Coefficient sensitivity, Sensitivity and noise.

4 DSP ARCHITECTURES AND SYNTHESIS OF DSPARCHITECTURES Total Hrs 9

DSP system architectures, Standard DSP architecture, Ideal DSP architectures, Multiprocessors andmulticomputers, Systolic and Wave front arrays, Shared memory architectures. Mapping of DSP algorithmsonto hardware, Implementation based on complex PEs, Shared memory architecture with Bit – serial PEs.

5 NUMBER SYSTEMS , ARITHMETIC UNITS ANDINTEGARTED CIRCUIT DESIGN Total Hrs 9

Conventional number system, Redundant Number system, Residue Number System .Bit-parallel and Bit-Serialarithmetic, Basic shift accumulator, Reducing the memory size, Complex multipliers, Improved shift-accumulator. Layout of VLSI circuits, FFT processor, DCT processor and Interpolator as case studies.Total hours to be taught 45Reference(s) :

1 Lars Wanhammer, “DSP INTEGRATED CIRCUITS”, Academic press, New York 1999.2 A.V.Oppenheim et.al, ‘Discrete-time Signal Processing’ Pearson education, 2000.3 Emmanuel C. Ifeachor, Barrie W. Jervis, “Digital signal processing – A practical.


40



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E19 BIO MEDICAL SIGNALANALYSIS 3 0 0 3 50 50 100

Objective(s) To know the concept about bio signal waves, Time series analysis and to discuss aboutremoval of artifacts and special topics on bio signal processing.

1 Bio Signal Wave shapes and Waveform complexity Total Hrs 9Introduction to Biomedical signals-overview and characteristics of ECG, ENG, EMG, ERPs, EGG, PCG, Carotidpulse, EOG, VMG, VAG, and Oto acoustic emission signals-Bio signal acquisition-conversion and analysis.Morphological analysis of ECG-Envelope extraction and analysis of PCG-Correlation and Cross spectralanalysis of EEG Channels.

2 Time Series Analysis And Spectral Estimation Total Hrs 9Time series analysis-linear prediction models-Time variant systems-Adaptive segmentation-SpectralEstimation-Blackman Tuckey method-Periodogram and model based estimation

3 Removal of Artifacts Total Hrs 9Noise sources in biomedical signals-Review of optimal filtering-adaptive filters-LMS&RLS Adaptive filters-Removal of Artifacts in ECG-Maternal-Fetal ECG-Muscle contraction interference-use of adaptive filters forsegmentation in ECG and PCG Signals.

4 Bio Signal pattern Classification and Diagnostic Decision Total Hrs 9Pattern classification as applied to Bio signals-supervised pattern classification-unsupervised patternclassification-Probabilistic models and statistical training and test steps-Neural networks-measures ofdiagnostic accuracy and cost-Reliability of classifiers and decisions.

5 Special Topics on Bio signal processing Total Hrs 9Application of wavelet transform-TFR representation-ECG Characterization-wavelet networks-datacompression of ECG and EEG signals-Application of chaos theory on Bio signals.Total hours to be taught 45Reference(s) :

1 Rangaraj. M.Rangayyan, ‘Biomedical Signal Analysis-A Case Study Approach,”IEEE Press-John Wiley& Sons Inc, New York-2002.

2 Arnon-Cohen, “Bio-Medical Signal Processing,” Vol I&II, CRC Press. 1995.3 W.J.Tompkins, “Biomedical Digital signal processing,”Prentice hall, New Jersey-1993.


41



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E20 INTERNETWORKING ANDMULTIMEDIA 3 0 0 3 50 50 100

Objective(s)To study of various compression techniques for audio and video signals. To emphasis theknowledge about modern MPEG technologies across multiple networks. To familiarize theconcept about various real time multimedia based application

1 MULTIMEDIA NETWORKING Total Hrs 9Digital sound, video and graphics, basic multimedia networking, multimedia characteristics, evolution of Internetservices model, network requirements for audio/video transform, multimedia coding and compression for text,image, audio and video.2 BROAD BAND NETWORK TECHNOLOGY Total Hrs 9Broadband services, ATM and IP, IPV6, High speed switching, resource reservation, Buffer management,traffic shaping, caching, scheduling and policing, throughput, delay and jitter performance.3 MULTICAST AND TRANSPORT PROTOCOL Total Hrs 9Multicast over shared media network, multicast routing and addressing, scaping multicast and NBMA networks,Reliable transport protocols, TCP adaptation algorithm, RTP, RTCP.4 MEDIA - ON – DEMAND Total Hrs 9Storage and media servers, voice and video over IP, MPEG over ATM/IP, indexing synchronization of requests,recording and remote control.5 APPLICATIONS Total Hrs 9MIME, Peer-to-peer computing, shared application, video conferencing, centralized and distributed conferencecontrol, distributed virtual reality, light weight session philosophy.Total hours to be taught 45Reference(s) :

1 Jon Crowcroft, Mark Handley, Ian Wakeman. Internetworking Multimedia, Harcourt Asia Pvt.Ltd.Singapore, 1998.

2 B.O. Szuprowicz, Multimedia Networking, McGraw Hill, NewYork. 19953 Tay Vaughan, Multimedia making it to work, 4ed,Tata McGrawHill, NewDelhi,2000


42



ElectronicsELECTIVE


L T P C CA ES Total

10 PAE E21 WAVELET TRANSFORMS ANDAPPLICATIONS 3 0 0 3 50 50 100

Objective(s)

To learn the basic concepts of linear algebra,to study about the aspects of time – frequencyanalysis Multi resolution analysis of construction of various types of wavelets.To study aboutDiscrete wavelet filter bank algorithm. To learn many interning applications of wavelets tosignal processing.

1 MATHEMATICAL PRELIMINARIES Total Hrs 9Linear spaces – Vectors and vector spaces – Basis functions – Dimensions –Orthogonality and biorthogonalilty– Local basis and Riesz basis – Discrete linear normed space – Approximation by orthogonal projection –Matrix algebra and linear transformation.2 TIME FREQUENCY ANALYSIS Total Hrs 9Window function – Short time Fourier transform – Discrete short time Fourier transform – Discrete Gaborrepresentation – Continuous wavelet transform –Discrete wavelet transform – Wigner-Ville distribution –Properties of Wigner-Villedistribution.3 MULTIRESOLUTION ANALYSIS Total Hrs 9Multiresolution spaces – Orthogonal, biorthogonal and semiorthogonal decomposition – Two scale relations –Decomposition relation – Wavelets construction – Orthogonal wavelets – Orthonormal scaling functions –Construction of biorthogonal wavelets.

4 DISCRETE WAVELET TRANSFORM AND FILTER BANKALGORITHMS Total Hrs 9

Decimation and interpolation – Signal representation in the approximation subspace– Wavelet decompositionalgorithm – Reconstruction algorithm – Change of bases – Two channel perfect reconstruction filter bank –Polyphase representation for filter banks.5 DIGITAL SIGNAL PROCESSING APPLICATIONS Total Hrs 9Wavelet packets – Wavelet packet algorithms – Thresholding – Two dimensional wavelets and wavelet packets– Wavelet and wavelet packet algorithms for two dimensional signals – image compression – image coding,wavelet tree coder, EZW code, EZW example.Total hours to be taught 45Reference(s) :

1 Jaideva C. Goswami and Andrew K. Chan, “Fundamentals of Wavelet- Theory, Algorithms andApplications”, A Wiley – Interscience Publication, 1999.

2 Rao RM and AS Bopardikar, “Wavelet Transforms”, Addison Wesley, 1998.3 Strang G Nguyen T, “Wavelet and filter banks”, Wellesley Cambridge Press, 1996.4 S.P.Soman, wavelet transform,PHI K.I. Ramachandran.


43


Department Electronics andCommunication Engineering



Elective

Course Code Course NameHours / Week Credit Maximum Marks

L T P C CA ES Total

10 PAE E22RESEARCH METHODOLOGY -ENGINEERING ANDMANAGEMENT STUDIES

3 0 0 3 50 50 100

1 RESEARCH METHODOLOGY Total Hrs. 9Research methodology – definition, mathematical tools for analysis, Types of research, exploratory research,conclusive research, modeling research, algorithmic research, Research process- steps. Data collectionmethods- Primary data – observation method, personal interview, telephonic interview, mail survey,questionnaire design. Secondary data- internal sources of data, external sources of data.

2 SCALES AND MEASUREMENTS Total Hrs. 9Scales – measurement, Types of scale – Thurstone’s Case V scale model, Osgood’s Semantic Differentialscale, Likert scale, Q- sort scale. Sampling methods- Probability sampling methods – simple random samplingwith replacement, simple random sampling without replacement, stratified sampling, cluster sampling. Non-probability sampling method – convenience sampling, judgment sampling, quota sampling.

3 HYPOTHESES TESTING Total Hrs. 9Hypotheses testing – Testing of hypotheses concerning means (one mean and difference between two means -one tailed and two tailed tests), Concerning variance – one tailed Chi-square test.

4 SAMPLE TESTS Total Hrs. 9Nonparametric tests- One sample tests – one sample sign test, Kolmogorov-Smirnov test, run test forrandomness, Two sample tests – Two sample sign test, Mann-Whitney U test, K-sample test – Kruskal Wallistest (H-Test)

5 ANALYSIS AND REPORT Total Hrs. 9Introduction to Disciminant analysis, Factor analysis, cluster analysis, multidimensional scaling, conjointanalysis. Report writing- Types of report, guidelines to review report, typing instructions, oral presentationTotal hours to be taught 45Reference(s):

1. Kothari, C.R., Research Methodology –Methods and techniques, New Age Publications, New Delhi,2009.

2. Panneerselvam, R., Research Methodology, Prentice-Hall of India, New Delhi, 2004.

Documents

Curriculum & Syllabus of M.E. Applied Electronicsksrct.ac.in/admin/file_manager/source/academic/curriculum/ME_AE_R...... CMOS transistor theory and logic design. ... Circuit using