CubaseLE Setup With SDR-1000

7/29/2019 CubaseLE Setup With SDR-1000

1/17

Configuring and using the CubaseLE software with your SDR-1000

Introduction:

You should have your SDR-1000 working properly with the Presonus Fireboxbefore you continue.

The first thing to note is that there is a complete manual provided as a PDF file with thesoftware. My purpose here is simply to get CubaseLE operating with the SDR so that you

can utilize its mixer properties and its onboard plug-ins (e.g. EQ and Dynamics)

to tailor your TRANSMIT audio.

Understand that the software in all its functioning has a rather steep learning curve and

that there are also other issues, such as latency, revolving around the particular computer

that the software is used with. The more horsepower and memory you have with your

computer the better. However this should not discourage you to try the software as youcan make adjustments - see the PDF manual.

Hopefully the instructions below and/or the supplied MASTER file posted on the Flex

Radio download site will get you up and running the CubaseLE software that came with

your Presonus Firebox.

Regarding the use of the startup file called Master see Appendix A at the end of this

document.

SDR-1000 External Wiring Setup:

When using the Cubase LE software with the SDR the following external wiring

changes are required:

(1)Your microphone will be plugged into Input 2 Mic/Instrutment (XLR) on thefront of the Presonsus Firebox.

(2) You will need to use a shortjumper cable with stereo inch phono plugs oneach end. This cable is to jumper Mic/Instrutment #1 on the front of the Presonus

(using the inch stereo jack in the center of the XLR) to the REAR OUTPUT # 6on the back of the Presonsus.

Connect this up BEFORE you start the procedure below so you can hear thesoftware working . You do NOT have to have the SDR turned on to do the install

or to play with the CubaseLE software and plug-ins, so do NOT have your SDR

on for this initial setup. Just have your Presonus firebox connected to yourcomputer

as normal ( as with your SDR) with the above 2 changes in place.


2/17

INSTALLATION OF THE CUBASE LE SOFTWARE

Insert the Cubase LE CD in your computer CD drive and the program should

auto play (start automatically). If not you can go into the directory of the CubaseLe CD

and start it from there. Follow the install instructions accepting its choices unless youhave other reasons to install it for example in a different directory. My advice is to accept

its choices. It will also ask you for the Installation Serial Number which can be found on

the envelope that the CD was in. If you get an Asio Multimedia Test Screen upon thecompletion of the software simply ignore it as we want Cubase LE to use the Presonus

Firebox and not any other card connected to or found in your computer. So for now

ignore the asio test if it appears.

SETTING UP CUBASE LE TO WORK WITH THE SDR.

The Simple Approach:

For those wishing the simple route you can try using the Master CubaseLE file on the

download portion of the Flex-Radio website . You however must first know how to call it

up within the software and have the Cubase Le software installed BEFORE you can use

the MASTER file, so please read Appendix A below and remember too the hardwiringinstructions provided above.

For those wanting to learn how to do to their own setup from scratch and in so-

doing learn about the software:

For those wanting to learn something about how to configure CubaseLE the following

procedure should be followed. This is essentially nothing more than the method required

to inform the CubaseLE software which soundcard or device (i.e. firewire or USB sound

device) is to be associated with the program and how that sound device is to be addressedIn our case we want CubaseLE to see the Presonsus Firebox as its audio device and not

another audio device.

Getting Started with CubaseLE.

1) Once you have installed CubaseLE double click the CubaseLE desktop icongenerated by your install or open the program from the windows START menu

You will get the following screen.


3/17

You can move the Tape Transport out of the way or close it by clicking the small square

in the upper right corner. You will NOT need to use it in the setup under discussion.

Again, you can read all about other items of the software in the PDF manual.

NB: I could not capture with my software (Snagit) all the windows I would have liked so

please pay attention to the sequences in the text and follow along carefully.

2) You will see running across the top of the Cubase LE screen a number of dropdown menus: e.g. FILE , EDIT, PROCESS etc.,

3) Click on FILE and since you want to generate a new, and in our case first, project,choose NEW PROJECT. This will open the NEW PROJECT choice screen. For

the sake of convenience choose 24 TRACK AUDIO RECORDER and click OKat the bottom of the New Project window.


4/17

4) You will then have the SELECT DIRECTORY window open. This is where youwill save your projects so you can load them easily into CubaseLe. You can havestored as many project files as you like to accommodate a wide variety of audio

configurations and settings. You can use the default folder choice or use the

CREATE button on the bottom of the Select Directory screen to generate a folder

with a unique name and location of your choice.

(The Cubase LE software will remember your choice of folder each time you openthe program.)

You may then get a yellow triangle explanation window telling you that

sample rate can not be set. Ignore this by simply clicking the OK

You can again ignore or close the tape transport and Marker indication box as you

will not need them. You can always get them back from the menu but you do NOT needthem here.


5/17

SETTING UP YOUR FIRST PROJECT TO SEE YOUR PRESONUS FIREBOX .

NB: You will likely find some screen items disappear from view when you click on an

item to bring it to the foreground. To find a missing item again just move your CubaseLEitems around with your mouse or get it via the top line running across the CubaseLe main

screen..

PART 1

On the top of the Cubase LE screen in front of you click on the DEVICES tab of the

menu running along the top of the CubaseLE screen. A new window will drop down.

Choose DEVICE SETUP at the very bottom of the list. A subsequent new window willopen. You will see running down the left hand side of that window a number of choices

starting with ALL MIDI PORTS. Choose the VST MULTITRACK option from the list.


6/17

You will then have a new screen open for you on the right hand side of the Device Setupwindow. You will notice beside one of the small black oblong rectangular windows the

text ASIO DRIVER. This is where you want to see the phrase PRESONUS ASIODRIVER (Firebox). If you do not see that text at this time then simply click on the

small downward arrow in the gray box beside the black rectangle and choose it. If youhave to make a change a window will come up asking: Do you want to switch the ASIO

DRIVER? Click on SWITCH.


7/17


8/17

You may then get the ASIO MULTIMEDIA window asking if you want to test your

choice of the Presonus Asio Driver you can say YES and hopefully it will complete with

an ok. If it does not, for now, carry on. You can deal with those issues later via the PDFmanual.

Click on the line VST SYSTEM LINK in the Device Setup window, If you clicked OK in

the previous asio driver screen and your window closed simply go back up to the top of

your Cubase LE screen and choose Device Setup again under the Devices tab.

You want to see the following text appear in the ASIO INPUT and ASIO OUTPUT black

rectangles. If you do not see it, simple click on the black arrow in the gray square at theside of each of the black rectangles and choose the following:

For ASIO INPUT = Mic/Instn 1 & 2 left

For ASIO OUTPUT = MainOut 1 & 2 left

Then choose OK at the bottom of the Device Setup screen.

Part 2

You will notice on the Cubase LE Project main screen running down the left hand side

the 24 AUDIO tracks. In track AUDIO 01 you will notice two grey rectangles withsymbols in them ( a dot in one case and a speaker in the other) on the left of that rack and

in fact on all the tracks. One of the buttons may already be colored red (i.e. initialized).


9/17

Click on the other button and it will turn orange in color. YOU MUST HAVE BOTHTHOSE BUTTONS colored to use the software with the SDR-1000. If you dont

have both colored it will not work properly !! So ALWAYS remember this fact .You canread the onboard manual to find out what any button in the software will do.

[NB: Once you SAVE your information for a Project you will not have to worry

about the above. Just remember it if you are creating another new project fromscratch or if you suddenly can not hear/see your transmit audio when you later usethe software with the SDR 1000 SDR.

You can of course simply modify existing projects and provide a new name for the new

project rather than start at the beginning every time.]

Part3

USING the MIXER and using PLUGINS.

1) From the Cubase LE Project window menu running along the top edge clickDEVICES and choose MIXER


10/17

Your 24 channel mixer will appear with sliders to adjust the levels. You are only

concerned here with one channel of the mixer and its Output channel at the extreme

right.

You will notice at the bottom of the output channel the words

MAINOUT 1 &2. Click on that line and a menu will drop down

with the choices: MainOut 12 Left

LineOut 34 LeftLineOut 56 Left

SpdifOut Left

Click on LINEOUT 56 Left and this will then assign the output you want


11/17

If everything is done correctly you should see your audio deflect in the input and

output tracks of the mixer. You do NOT need to have your SDR powered up to see

this audio deflection. The SDR should be off as we indicated earlier for thispreliminary setup. You should now also hear your audio in the output jack 5 and 6 on

the back of the Presonus Firebox. You can plug a pair of headphones in to hear it. .If

you play with the mixers active channel and output channel sliders (the whiterectangles on the channel) you can adjust your audio level.

NB: Your audio level is also affected by the Presonus controls on the front of

your Firebox so makesure these are set up properly.

This will now allow you to operate your SDR-1000 with CubaseLE/ butconclude the instructions first to learn more.

2) Playing with plug-in e.g. adjusting an EQ.In order to use the EQ plug-in that came with your CubaseLE software you do as

follows:

You will notice at the top of each of the channels of your Cubase mixer 6 grey

squares with symbols in them, one of those squares (at the bottom LEFT ) has an e.This e is for equalizer. If you click the e a 4 band parametric EQ will open up.

You can adjust the eq by pulling the flat trace line up or down OR by adjusting the bands

via the controls of the EQ beneath its screen. Full details of these controls are in themanual. One thing to remember is that IF you use the controls to set up the eq bands you

must activate each band by clicking on the gray square above the control it goes green

when you click on it. If you pull the trace line (up or down) the squares will go green (on)


12/17

automatically. You can now listen to your audio change in real time if you play with the

trace or the controls.

To add other plug-in to your project

You will notice on your EQ screen to black squares on its left hand side with the

words NO EFFECT. If you want to add an EFFECT click inside that square.

You will then see a list of effects appear. If you click on one of those effects it will

automatically install itself in the channel along with the EQ.

A list of the Effects details can be found in the manual. REMEMBER most of these

effects apply to music and will not do anything for you with the audio you want forvoice communications with the SDR. You can however utilize things like

DYNAMICS and REVERB. You will have to learn from the onboard PDF manualhow to use these, turn them on, adjust the levels etc., There are many suppliers ofplug-ins available to you to purchase and demo on the web or from your local audio

Shop. See the photos at the end of this setup.


13/17

Once you have established a project you like you can save it. You do this by going to

the top of your CubaseLE screen and choose FILE then SAVE AS. You can then

provide a unique name for your project and save it. You can also always modify an

existing project and save it with another name as an entirely new project.

Once you have saved the project you can call it up at will anytime you want. You

simply call up your CubaseLE software and under FILE choose OPEN and you willsee your various projects. Click on the one you want and it will install.

USING THE CUBASE LE SOFTWARE WITH THE SDR AFTER

COMPLETING THE SETUP.

1) Turn on the SDR first , then open the Cubase Le software after you have the SRworking. Select your PROJECT choice in CubaseLE and you should have the

software working with your SDR in transmit.. When you transmit you will begenerating your audio through the CubaseLE software and your specific choice of

project. You can adjust your CubaseLe plugins on the fly in real time even while

transmitting. Also remember that your SDR mic level , eq etc., will affect the

working levels and sound of your cubase project.


14/17

There are other issues such as hearing your transmitted audio which I can not go into

here. Hopefully others will find new ways to operate with digital software programs like

CubaseLE. To try to anticipate all the possible issues here is just not possible. Hopefullythis gets everyone started and other minds can build on the above instructions.

IF you want to use your SDR without CubaseLe simply

put your microphone directly into XLR 1 on the front of

the Presonus and close down CubaseLE.

CONCLUDING REMARKS:

The use of digital mixing software can be confusing even if one has a manual.Hopefully the above setup will have worked for you. You can then go to the PDF

manual and make your own setup choices as there is more than one way to set up and

operate CubaseLE.

There are issues that may arise with latency which may require you to make changes

with the buffer size in CubaseLE etc. These are discussed in the manual.

There are also hundreds of other PLUG-INS available that could be used with

CubaseLE many can be found free on the web and others can be purchased after you

demo them.

Take a look at the following 2 sites as examples:

http://waves.com

http://pspaudioware.com

I provide a few pictures of what one could have available if you wish to go further in

acquiring more plug-ins . These again are NOT supplied with CubaseLE


15/17

IF you want to utilize a large number of plug-ins at any one time it will be necessary topurchase a new professional version of the CubaseLE software such as CubaseSX3.


16/17

Cubase LE allows for only a few plug-ins at any one time. You can visit the Steinberg

site on the web and see the packages available. I provide a shot of such a setup where

many plug-ins can be used at one time under another Steinberg program..

APPENDIX A

Using the shortcut of simply loading the MASTER file.

If you want to avoid configuring Cubase LE from scratch as described above youcan try loading the Master file into CubaseLE after first installing the CubaseLe

software . You must install the software to use the MASTER file you can

download from the Flex Radio website.

Once you have installed the CubaseLE software you can put the MASTER file

into a folder where you can find it.

To use the Master file you open (start) the CubaseLE program from the desktop icon

or the windows Start menu and then under FILE (in the CubaseLE startup window


17/17

that runs along the top edge of the Cubase LE screen) choose OPEN and direct the

software to where the Master file you downloaded is located. You then simply click

on it (select it) and hopefully Cubase LE will be correctly configured for use with theSDR 1000. Again you can test things out by plugging a pair of headphones into the

output jacks (5 or 6) on the back of the Presonus Firebox.

To use any plug-ins read the PDF manual or my remarks above.

Remember to OPEN your SDR program first , then open cubaseLE if you want

to use CubaseLE with the SDR . Remember of course to hardwire the Firebox

as I have outlined above.

Good Luck!

Documents

CubaseLE Setup With SDR-1000