Crude Oil and E&P Testing - Stanhope-Seta D4007; D96 (Obs); D1796; D2709; ISO 9030 • Specifically designed for testing oils • Heated chamber, ambient to 80°C • Static, near

Crude Oil and E&P TestingLaboratory Instruments for quality control, analysis and calibration

Stanhope-Seta, London Street, Chertsey, Surrey, KT16 8AP, UK t: +44 (0) 1932 564391 | e: [email protected] | www.stanhope-seta.co.uk

H2S Part No: SA4000-3

VPP Part No: SA4015-0

Crude Oil Test Kit: SA4021-0

H2S Analyser range: 0-250 mg/kg in the liquid phase (0-250 ppm H

2S)

Viscosity Range: Up to 3000 mm2/s

Principle of measurement: Advanced Electrochemical sensor

Test duration: 25 minutes with VPP

Sample size: 1ml, 2ml, 5ml (depending on H2S concentration)

Diluent volume: 20ml

Size (HxWxD) /Weight: H2S Analyser: 21 x 30 x 41 cm / 8kg

VPP: 40 x 24 x 20 cm / 7.8kg

H2S Analyser with Vapour Phase Processor (VPP)TM

(SA4000-3 & SA4015-0)ASTM D7621 Appendix X1; IP 570 Procedure A

• Measurement range from 0-250 mg/kg H2S (0-250 ppm H

2S) in the

liquid phase

• Vapour Phase Processor proven to eliminate effects of chemical interference

• A non chemical method, no wet chemistry involved

• Small lab bench footprint, fully portable operation

• Suitable for monitoring crude oils in the distribution system

• Critical Measurement method for Product Safety and Release

The H2S Analyser was developed with Lloyd’s Register’s ‘Fuel Oil and Bunker

Analysis Service’ (FOBAS) along with support of other major international oil companies to offer rapid measurement of H

2S in petroleum products. The VPP

accessory was subsequently developed to eliminate the effects of chemical interference and to enable the analyser to address a broader range of petroleum products. The Crude Oil Test Kit (SA4021-0) allows the H

2S Analyser to be used for

testing Crudes and provides a highly cost effective test giving repeatable results even at low gas levels.

The H2S Analyser is an excellent tool for supporting product Quality Control and

safety ensuring product is within approved specification. It is also ideal for both product remediation treatment of feedstock components and off-spec products with fast repeat sample measurement capability.

H2S is efficiently purged from the test sample by a combination of heat and

agitation, and is measured by an advanced electrochemical sensor. The instrument offers a cost effective solution for H

2S measurement – no costly chemicals are

required and there is no need for analytical preparation by an expert chemist.

View a demo video at: www.stanhope-seta.co.uk/4909/H2S-Analyser

› SA4000-3 & SA4015-0


Crude Oil and E&P Testing

2

Crude Oil Test Kit (SA4021-0)The Crude Oil kit allows the H

2S Analyser to be used with the Vapour Phase

Processor for testing Crudes in accordance with Appendix X1 of ASTM D7621.

› New Test Vessel

› Crude Oil Test Kit

IP 570 Proficiency Test Scheme (PTS)IP 570/14a Mandated Verification Procedure

PTS is an invaluable Quality Assurance tool allowing participants to:

• Evaluate and monitor laboratory and instrument performance

• Provide additional confidence by demonstrating compliance with laboratory accreditation requirements

• Identify inter-laboratory differences by the comparison of test results and calculated statistical parameters with other laboratories in accordance with ISO/IEC 17025

• Identify problems such as inadequate test or measurement processes and procedures

• Identify problems with the calibration of laboratory test equipment

Visit: www.stanhope-seta.co.uk/4418/IP-570-PTS-Quarterly-membership › SA4032-0 IP 570 PTS Pack

Seta Part No: 4 place: 90000-3 or 6 place: 90100-0

Maximum RCF: 2214g

Maximum RPM: 3000

Temperature Range: 30 to 80°C (± 1°C)

Timer Range: 1 to 60 minutes in 1 minute steps, Continuous Operation

Rotor Capacity: 4 or 6 place samples

Power Requirement: 230Vac (110V transformer option) 50/60Hz / 1kW

Size (HxWxD) / Weight: 40 x 56 x 64cm / 86kg

Seta Oil Test Centrifuge for Sediment & Water ASTM D4007; D96 (Obs); D1796; D2709; ISO 9030

• Specifically designed for testing oils

• Heated chamber, ambient to 80°C

• Static, near vertical bucket positioning

• 4 or 6 place swing out rotor

• Membrane ‘touch’ control panel

• Pre-heat facility to ensure bowl is at test temperature prior to test

• Conforms to IEC 1010-1 & 1010-2-D safety requirements

The Centrifuge has a large diameter chamber, with four or six place rotor and cushioned adaptors, which allows the use of 6 and 8 inch conical, pear-shaped, trace sediment and 12.5ml tubes. The swing out rotor ensures that the samples are held near vertical when at rest allowing more precise measurement of sediment. An optional hazard reduction system extracts vapours and gases released from volatile samples.

4-Place Centrifuge (90000-3): www.stanhope-seta.co.uk/3943

6 place Centrifuge (90100-0): www.stanhope-seta.co.uk/4807

Centrifuge Tubes• 100ml Long & Short Cone, Trace Sediment, and 12.5ml Finger Tubes

• Manufactured in strict compliance to test methods

• Permanently etched graduations

• High visibility white lined markings

• Optional factory certified, 7 point, long cone tubes

Salt Content in Crude Analyser (99700-5)ASTM D3230; IP 265

• Automatic salt concentration calculation

• Pre-calibrated for immediate use

• Membrane touch screen

• Interchangeable sensor

• 3 operating modes (ASTM, IP, user defined)

• Verification mode

• Battery or mains voltage operation

• Moistureproof

A portable instrument for determining the approximate chloride (salts) content of crude oils. The instrument is pre-calibrated and automatically calculates the salt concentration in g/m3 or pounds per thousand barrels (ptb) (lb/1000bbl). Measurements can be displayed or downloaded to a PC. The instrument is supplied with carry case, mains adaptor, software, RS232 cable and instruction manual. An optional bench stand is available as an accessory (99701-0).

Visit: www.stanhope-seta.co.uk/4504/Salt-in-Crude-Analyser

SaltCheck - Salt in Crude Analyser Verification Tool (99703-0)A set of 3 ‘SaltCheck’ verification modules which are calibrated to show equivalent salt values of 0 g/m3, 30 g/m3 and 190 g/m3. Instrument verification is easy - simply switch the instrument on and place the sensor into each ‘SaltCheck’ module to confirm that the correct reading is being displayed. Saltcheck is supplied in a convenient storage case with a certificate of verification.

Visit: www.stanhope-seta.co.uk/4716/Salt-Check-Verification-Tool

Seta Part No: 99700-5 Salt in Crude Analyser99703-0 Verification Tool99701-0 Base Unit

Conductivity range: 0 .0 to 151 lb/1000bbl(Res:0.1lb/1000bbl) 0.0 to 430.0 g/m3 (Res: 0.1 g/m3)

Temperature range: -20°C to 150°C (Res: 0.1°C)

Power supply: 9 volt dc battery or mains adaptor 110/240v, 50/60Hz adaptor supplied

Size (HxWxD) / Weight: 20 x 7 x 3.5cm / 1.6kg (including case)

› 99701-0 Base Unit

› 90000-3

› Centrifuge Tubes

› 99700-5

› 99703-0


3

Laboratory instruments for quality control, analysis and calibration

Setavap3 Automatic Vapour Pressure Tester (80500-0) ASTM D5191; D6378; D6377; D6897; D5188; EN 13016-1, 2 & 3; IP 394, 409, 481, Correlates with ASTM D323; D4953; D5190; D5482; D1267

• Rapid automatic vapour pressure testing

• Mini methods – 1 ml sample volume

• 0 to 1550 kPa pressure range

• 0 to 120oC temperature range

• Integrated shaker

• Robust measuring chamber/Valves/piston mechanism

• Results available as DVPE, RVPE VPx Ptot, TVP, Pabs ASVP, T(V/L)

• Easy to use, large colour touch screen

• Test memory: >4 Million test reports

SetaVap 3 provides the next generation of automated vapour pressure testing. The design implements a robust measuring chamber with a movable piston for testing gasoline, solvents, crude oils, LPG and similar products in strict compliance with ASTM, IP and ISO methodology. SetaVap 3 is suitable for a broad range of applications including terminals, refineries, mobile testing, independent laboratories and R&D. SetaVap 3 is extremely easy to operate and can be calibrated in the field, its large colour touch screen allows single press to test functionality and minimises operator involvement. Results are clearly displayed and can be captured using a QR code, emailed, saved to a memory stick, output to LIMS or produced in hard copy with the printer option.

Visit: www.stanhope-seta.co.uk/5056/SetaVap3-Automatic-Vapour-Pressure-Analyser

SetaVap2 Rapid Automatic Vapour Pressure Tester (81000-2) ASTM D5191; IP 409; IP 481; IP 394, EN 13016; Correlates with ASTM D323; D5842; D6378; IP 69

• Multi-Mode - Ptot, DVPE, EPA, Crude, Pabs

• Fixed Liquid/Vapour ratio

• “Mini” method uses only 3ml sample size

• Automatic Drain and Purge

A quick and simple to use instrument for determining the vapour pressure of gasoline, solvents, light crude oils, and similar products using the “Mini” test method.

SetaVap2 is highly automated with step by step instructions and prompts being displayed on the control panel. Once the test procedure has been started operator intervention is only required to inject the sample into the chamber, the purging and cleaning cycle is carried out automatically.

Visit: www.stanhope-seta.co.uk/2984/Setavap-2-Vapour-Pressure-Tester

Crude Oil Filtration Apparatus (19727-0)ASTM D4807

Determines the sediment in crude oils by membrane filtration in accordance with ASTM D4807. This test method has been validated for crude oils with sediments up to approximately 0.15 mass %.

The Apparatus comprises: Insulated Funnel with heating coil (2 parts), bung, clamp, pack of filters (100), Seta steel stand, boss head, clamp, tubes with valves and clips, Buchner flask (500ml), grounding kit including mat, grounding cable assembly, earth bonding plug, earth bonding cord. Supplied with Works Certificate.

Visit: www.stanhope-seta.co.uk/4867

› 19727-0

› 81000-2

Seta Part No: 80500-0 81000-2

Temperature Range: 0 to 120°C 37.8 °C ±0.1°C

Pressure Range: 0 to 1550kPa 0 to 200kPa ±0.5kPa (0 to 29psi ±0.1psi)

Pressure Resolution: Conforms to Methods 0.1kPa (0.1psi)

Units of Pressure: kPa or psi (user selectable) kPa or psi (user selectable)

Vacuum Requirement: Not Required better than 0.01kPa (abs)

Voltage: 100/240VAC 50-60 Hz (Auto) 110/120V or 220/240V, 50/60Hz (switchable)

Power: 230W 70W

Size (HxWxD)/ Weight: 38 x 23 x 37cm / 16kg 37 x 13 x 20cm / 3.5kg

› 80500-0



4

KV-6 Viscometer Bath (84200-2)ASTM D445

• Up to 6 viscometer tubes

• 50 litre oil/water bath

• Temperature stability ±0.002 at 40°C, ±0.005 at 100°C and ±0.01 at 150°C

• Temperature range ambient to 150°C

• Digital display with 0.01°C resolution

• Toughened glass front panel

• Integral back lighting

50 litre temperature controlled bath that can accommodate up to six standard viscometer tubes. Digital temperature control and an inbuilt cold water cooling coil provide accurate and stable test temperatures from ambient to 150°C. The bath is protected by low liquid level and overtemperature cut-outs.

The bath is equipped with a toughened glass front window, easily accessible drain valve, integral back lighting, top plate, and provision for reference thermometer.

Visit: www.stanhope-seta.co.uk/4472/KV6-Viscometer-Bath

Temperature Range: Ambient to 150°C

Temperature Stability: ±0.002 at 40°C, ±0.005 at 100°C, ±0.01 at 150°C

Tube Capacity: 6

Bath Fluid: Oil or Water

Bath Capacity: 50 Litres

Power Requirement: 2.2kW


› 84200-2

Viscometer Operating KitsComprises all items required for using glass capillary viscometer tubes.

• Ubbelohde/Suspended level (84212-0)

• BS U Tube (84214-0)

• U tube reverse flow (84213-0)

• Cannon Fenske Routine (84211-0)

• Cannon Fenske Opaque (84210-0)

Seta Dean & Stark AssemblyASTM D95; D244; D4006; IP 74; IP291; IP358

• Accepts 500ml flasks

• 200W Mantle type heater

• Integral energy regulator

This test provides an indication of the volume of water present using the Dean and Stark distillation procedure.

Seta offer a range of flask heaters, stands and condensers for Dean and Stark Assembly. Please visit our website for more information.

Seta Asphaltenes Apparatus (21200-0) ASTM D6560

• Determines the amount of wax free material insoluble in n-heptane but soluble in hot toluene

• Applicable for crude petroleum which has been topped up to an oil temperature of 260°C

• Comprises condenser, extractor, stoppers, stirrer, funnel and evaporation dish

Visit: www.stanhope-seta.co.uk/3106› 21200-0

› 24410-5


5


Multiflash Automatic Multi-Method Flash Point TestersABEL IP 170; TAG ASTM D56

• Highly automated low cost Modular System with in-built safety

• Strict conformity to test methods

• Fast and reliable performance

• Gas or Electric Ignition

• Temperature in °C or °F

The Seta Multiflash Universal Base can be used with either an Abel or Tag module to conform precisely to reference test methods.

Visit Multiflash ABEL (34200-0): www.stanhope-seta.co.uk/2970

Visit Multiflash TAG (34400-0): www.stanhope-seta.co.uk/2972

PM-93 Pensky-Martens Flash Point Tester (35000-0)ASTM D93; IP 34; ISO 2719

• Temperature range ambient +5 to 400°C

• Easy ‘3-step to test’ operation involving minimal operator intervention

• Unique ‘SafeFlash’ fire extinguishing system

• Large touch screen

• Single action lifting pod

• Small, compact footprint

• Seta ‘Ignite’ - robust and long lasting ignitor

• 30 programmable test profiles, test methods & sample names

• Rapid fan assisted cooling

• Optional barcode reader available

The Seta PM-93 is a fully automated Pensky-Martens Closed Cup Flash Point Tester which combines strict method conformance with state of the art control technology and safety systems to provide the next generation of automated precision flash point instruments.

View demo video: www.stanhope-seta.co.uk/pm-93-flashpoint-video.html

› Multiflash Abel Module

Setaflash Series 8 ActiveCool Closed Cup Tester (Flash/No Flash & Ramp Modes) ASTM D3278; ASTM D3828; ASTM D7236; ASTM E502; IP 523; IP 524; IP 534; ISO 3679; ISO 3680 (obs)

• Temperature range -20 to 130°C or Ambient +5 to 300°C (Depending on model)

• Small sample size, 2 or 4ml

• Corrosion Resistant cup option

• Electric ignitor (with gas option)

• Automatic dipping and flash detection

• ActiveCool electronic Peltier cooling

• 64 Test memory & RS232 interface

• °C or °F temperature display

• Barometric pressure correction

Setaflash Series 3 (Rapid Equilibrium And Ramp Tests) ASTM D3278; D3828; D7236; IP 523; IP 534; ASTM E502; ISO 3679; ISO 3680 (obs)

• Sub-Ambient Tests and Rapid Cool Down

• Temperature range 10 to 130°C or Ambient to 300°C (Depending on model)

• Rapid Equilibrium and Ramp tests

• Corrosion Resistant option

• 1 Minute Flash / No Flash and Actual Flash Point

• 2/4ml Sample Size

View a Series 3 and Series 8 demo video at: www.stanhope-seta.co.uk/setaflash.html

› 82000-0

› 30000-2

› 35000-0



6

SetaStill Distillation Unit (11860-3) ASTM D86; IP 123; ISO 3405

• Ambient to 400°C distillation range

• Adjustable height heater/flask platform

• Toughened glass window

• Cooling fan

The distillation unit, mounted to the left, comprises a flask support mechanism, heater elements, and the heater controller. The flask is supported by a drop-in ceramic-glass support board mounted to a platform that is adjustable for height.

The quartz enclosed heating elements are also attached to the platform, and are powered by a solid-state energy regulator and calibrated control. A cooling fan is installed in the rear of the distillation unit to reduce cooling time between distillations.

The condenser unit is attached to the distillation unit, and may be used with either a static fill of coolant or a laboratory cooling supply.

Visit: www.stanhope-seta.co.uk/3391/Setastill-Distillation

Seta Extraction Apparatus (21300-0) ASTM D473-IP 53; ISO 3735

• Sediment content of crude and fuel oils

• Comprises a tinned copper condenser coil, alumina refractory thimble of porous grade and a 1 litre Erlenmeyer flask

Determines sediment content of crude oil and fuel oils by extraction with toluene. The sample is placed in a refractory thimble and washed with condensed toluene vapours leaving only insoluble matter, the residue is calculated as a percentage of the total mass.

› 21300-0

Distillation range: Ambient to 400°C

Condenser Tank Volume: 7.2 litre


Seta Cloud and Pour Point Cryostat (93531-7)ASTM D97; D5853; IP 15; ISO 3016

• Four Individually temperature controlled compartments • Three compartments ambient to -35° (±1.5°C)• One compartment -35°C to -51°C (±1.5°C)• 2 litre bath capacity in each compartment • Four air wells in each compartment • Independent temperature control • Two stage ‘CFC free’ refrigeration system • Heated ‘anti-condensation’ lid

The Seta Cloud and Pour Point Cryostat has Four 2 litre compartments which are independently temperature controlled and can accommodate four Air Wells. Three compartments have a temperature range of ambient to -35°C and one has a low temperature compartment -35 to -51°C. The lid is electrically heated to prevent the formation of ice and condensation.


Compartment quantity: 3 + 1 low temperature

Compartment volume: 2 litre

Total test positions: 16

Temperature range: Ambient to -35°C (x3), -35°C to -51°C (x1)

Ambient temperature range: 15° to 32°C

Cool down Time (single compartment): Approx 2 hrs (from 32°C to -51°C)

Power supply: 1.8kW


› 93531-7

› 11860-3


7


Seta Ash Furnace (99220-2) ASTM D482-IP 4, ISO 6245-EN 7

• Pre-heated airflow system and extended chimney

• Maximum temperature 1100°C with over-temperature cut-out

• Door safety power cut off switch

The Seta Ash Furnace has a maximum temperature of 1100°C, it incorporates pre-heated airflow system and extended chimney.

The furnace is supplied with an Inconel tray complete with detachable handle, it features a door safety power cut-off switch as well as over-temperature cut out protection. The chambers of the furnace are ceramic muffles wound with resistance wire.


Capacity: 7 litres

Chamber size (HxWxD): 9 x 17 x 46cm

Power: 3.9kW

Voltage: 220/240V, 50/60Hz


Micro Carbon Residue Tester (97400-3)ASTM D4530; IP 398; ISO 10370 (Micro Method). Equivalent to ASTM D189; IP 13

• Carbon residue range 0.1% to 30.0% (m/m)

• 12 sample capacity

• Automatic temperature ramp and gas control

• Digital display flowmeter

• Temperature range ambient to 500°C

Automatic instrument designed to run tests to determine the carbon reside formed after evaporation and pyrolysis of petroleum products as per ASTM and IP test methods. The instrument comprises of an oven and insulating lid with curved top plug as defined in ASTM D4530 and IP 398. Nitrogen gas purging and temperature RAMP sequences are fully automatic and no operator intervention is required when running the test. A digital mass flow meter and high precision temperature control system ensure compliance to the methods.

Visit: www.stanhope-seta.co.uk/4882/Micro-Carbon-Residue-Tester

Temperature Range: Ambient to 500°C ±2°C

Ramp Rate: 10 to 15°C/min

Pressure controller: 20 to 750kPa

Primary pressure: 1400kPa max

Flowmeter: 0.1 to 1 litre/min

Flow Rate: Automatic, 150ml/min or 600ml/min


› 97400-3

› 99220-2

| Issue 1Stanhope-Seta, London Street, Chertsey, Surrey, KT16 8AP, UK t: +44 (0) 1932 564391 | e: [email protected] | www.stanhope-seta.co.uk | Issue 2


Documents

Crude Oil and E&P Testing - Stanhope-Seta D4007; D96 (Obs); D1796; D2709; ISO 9030 • Specifically designed for testing oils • Heated chamber, ambient to 80°C • Static, near