Erection Testing &

Commissioning

AMCShutdown Activity

Licensed Electrical

Contractor

Control Panel Manufacturing

Relay CoordinationShort Circuit

Arc Flash

Consultant Engineering

CRPCRP Control EngineersISO 9001 : 2015 Certified Company

0360Electrical Services

Company Profile

ABOUT THE COMPANY

AIM

CRP CONTROL ENGINEERS is ‘The Total Solution Provider’ to give the customers 360° Electrical Services under one roof.

MANUFACTURERS

Power Control Centre

Motor Control Centre

Lighting Distribution Panel

Power Distribution Panel

DG Synchronisation Panels

VFD Panels

APFC Panels

PLC Based Power Panels

PRODUCTS

Transformers

Ring Main Unit / HT Panels

Meters

Switchgears

Ladder/Perforated Cable Tray

Changeover Switches

Power Capacitors

Voltage Stabilizers

Cables & Wires

Jointing Kits

Cable Gland & Lugs

GI / Copper Earthing Sets & Strips

Lighting Fittings

Transformer Oil

CRP

SHUTDOWN SERVICES

Panel Servicing

Transformer Servicing

HT Panel/RMU Servicing

Routine Testing of Transformers as per IS

Relay Testing by Primary/Secondary Injection

Sandwiched type Bus duct/ Riser Servicing

OIL FILTRATION

Oil Filtration is used to enhance the insulation properties

of oil and enhance the life of transformers.

ONLINE EARTH RESISTANCE CHECKUP

Quick and precise resistance measurements

by online Fluke Earth ground testers.

Finding out leakages in Electrical Systems.

Soil resistivity measurements.

CRP

CRP

Consultant Engineering

Installation Testing And Comissioning Of Transformers.

Installation Testing And Commissioning Of RMU /HT & LT Panels, DG Sets,

Busducts.

Installation Of Cable Trays And Cables.

Chemical Earthings.

Laying Of HT XLPE Cable And Termination Of HT Cables.

Transformer / DG / Panel Painting.

OTHER SERVICES

HT PANELS SUPPLY & INSTALLATION

HT CABLE WORK - RAYCHEM

CRP

Arc Flash Analysis by ETAP Software

Short Circuit Analysis by ETAP Software

Relay Coordination by ETAP Software

ARC FLASH / SHORT CIRCUIT / RELAY COORDINATION

INSTALLATION OF DG SETS

INTEGRATED SYSTEM TEST

66 KV SWITCHYARD

Integrated System Test involves the overall testing of systems present in the

facility and their dependency on each other.

HT/ LT Panel / Transformer / DG Logic Testing

UPS Transfer & Retransfer Test

ATS / STS Logic Test

PAC Operation/ Redundancy Test

Gas Suppression System Test

Vesda / WLD Test

Fire Alarm System Test

Fire Hydrant System Test

CRP

LICENSED ELECTRICAL CONTRACTOR

Registered With Reliance Infrastructure Ltd.

Approvals From Central Electricity Authority / PWD Department

Insulation / Earth Resistance Check Up With Test Report

POWER QUALITY & HARMONICS ANALYSIS

Power Quality monitoring in compliance with EN 50160 at Main Incomer

Power Quality monitoring at UPS input / output

The above included logging of power and P.Q. parameters such as-

RAW POWER

KW, KVA, KAVR, PF and DPF

Harmonics in voltages and currents

Dips, swells, rapid changes in voltages

Imbalance in supply voltages

Power frequency violations

Recording of switching transients

CONDITIONED POWER

Crest factor of voltages

Monitoring DPF trend

Output voltage regulation

Recording Noise in voltage

THERMOGRAPHY

LOOP IMPEDANCE & ELCB TEST

Non intrusive visual recording of Electrical

Installation to highlight Hot Spots and areas

prone to failure due to persistent high

temperature.

Loop Impedance Test

RCD Testing from 10mA to 1000mA

Auto RCD Testing

Non-Trip Loop Testing

CRP

PORTABLE APPLIANCE TESTING

PAT test is a routine inspection of portable

electrical appliance to check they are safe to

use. Its purpose is to prevent electrical

accidents in workplace.

PAT test includes visual inspection,

operation test, earth continuity, lead polarity,

insulation resistance, alternative leakage,

RCD test, flash test & microwave leakage

test.

LIGHTING AUDIT

Lighting Audit is to save energy and to give better

illumination.

ONLINE ENERGY METER CALIBRATION

Online Energy Meter/ Ammeter/ Voltmeter Calibration.

In online calibration, CT Faults, Wiring Faults can also

be captured.

Meter Calibration is carried out by Fluke make Class A

(0.1% Accuracy) Energy Analyzer.

No Shutdown required for calibration of Meter.

ELECTRICAL/FIRE/SAFETY/RISK AUDIT

Design Adequacy of the Installation

Power Distribution & General Installation Review

Review of System Safety with respect to Installation as per I.E. Rules

Electrical Energy Bill Monitoring

Reporting Diu- Diligence report on electrical & fire system

Review of Standby & Redundancy

Scope for Improvements

Office:A/202B, Jaswanti Allied Business Centre, Kachpada Ramchandra Lane, Malad (W), Mumbai – 400 064.

Tel: +91 22 49728784

Works:Unit No: 14, Anil Singh Compound, Village Malvani,

Kharodi, Malad West, Mumbai - 400 064.Tel: +91 9004092069

In case of special attention contact: Mr. Ramesh Jhunjhunwala

Mob: +91 9323901534Email: ramesh@crpcontrol.com

Website: www.crpcontrol.com

CRPISO 9001 : 2015 Certified Company