CRIB / BEDASSEMBLY

INSTRUCTIONS

This crib has been designed for your child’s comfortand your convenience. Quality material and workmanshiphave gone into this crib, which will provide a sound andcomfortable bed for your baby if properly assembled andmaintained. For the security of your child and your ownpeace of mind be sure to follow the assembly instructionsexactly. A periodic check should be made of all screws andtighten if needed.

Moisture and heat are harmful to finish materials, forthis reason use caution when a vaporizer or humidifier is inuse.

Some types of soft plastic toys that come into contactwith finish materials could also be harmful to the finish onyour furniture.

BELLINIBARRY IMPORTS EAST CO.

165 OVAL DRIVEISLANDIA NY 11722 USA

BELLINICAL - LINDA IMPORTS INC.

2216 A AGATE COURTSIMI VALLEY CA 93065 USA

READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIBKEEP INSTRUCTIONS FOR FUTURE USE

BE_03_01

2

3

WARNING: FAILURE TO FOLLOWTHESE WARNINGS AND THE ASSEMBLYINSTRUCTIONS COULD RESULT IN SERIOUSINJURY OR DEATH.

� READ ALL INSTRUCTIONS BEFOREASSEMBLING CRIB.

� KEEP INSTRUCTIONS FOR FUTURE USE.

� BEFORE EACH USAGE OR ASSEMBLY,INSPECT CRIB FOR DAMAGED HARDWARE,L00SE JOINTS, MISSING PARTS ORSHARP EDGES.

� DO NOT USE CRIB IF ANY PARTSARE MISSING OR BROKEN. ASK YOURDEALER OR WRITE TO MANUFACTURERFOR REPLACEMENT PART ANDINSTRUCTIONAL LITERATURE IF NEEDED.

DO NOT SUBSTITUTE PARTS.

� AFTER RAISING SIDE, MAKE SURELATCHES ARE SECURE.

�WHEN CHILD IS ABLE TO CLIMB OUT ORREACHES THE HEIGHT OF 35 INCHES (90CM), THE CRIB SHALL NO LONGER BEUSED.

4

�DO NOT PLACE CRIB NEARWINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY STRANGLE A CHILD.

� IF REFINISHING, USE A NON-TOXIC FINISHSPECIFIED FOR CHILDREN'S PRODUCTS(LEAD-FREE).

�DO NOT USE A WATER MATTRESSWITH THIS CRIB.

�REPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE.

�DO NOT LEAVE CHILD IN CRIB WITHSIDE LOWERED. BE SURE SIDE IS RAISEDAND LOCKED IN POSITION WHENEVERCHILD IS IN CRIB.

�WHEN CHILD IS ABLE TO PULL TOSTANDING POSITION, SET MATTRESS TO LOWEST POSITION AND REMOVE BUMPERPADS, LARGE TOYS AND OTHER OBJECTSTHAT COULD SERVE AS STEPS FORCLIMBING OUT.

� THE DIMENSION FROM THE TOP OF THEMATTRESS TO THE TOP OF THE SIDE,WHEN THE SIDE IS IN ITS LOWESTPOSITION SHOULD BE A MINIMUM OF 3INCHES. THIS CAN BE OBTAINED BYLOWERING THE MATTRESS SUPPORT TO

5

A POINT WHERE THIS OCCURSSATISFACTORILY. AS YOUR BABY GROWSAND BECOMES ACTIVE AND MOBILE, BESURE TO LOWER THE SPRING ANDMATTRESS TO THE BOTTOM POSITION.WHEN YOUR CHILD REACHES A HEIGHTOF 35 INCHES, HE SHOULD BE PLACED INA YOUTH BED, OR A REGULAR BED.

� NEVER USE PLASTIC SHIPPING BAGSOR OTHER PLASTIC FILM AS MATTRESSCOVERS BECAUSE THEY CAN CAUSESUFFOCATION.

� CARE: CLEAN ONLY WITH DRY CLOTH.DO NOT USE ANY CHEMICALS TO CLEANCRIB.

� STORAGE: STORE CRIB IN A DRY, COOL,CLEAN ENVIRONMENT.

WARNINGSTRINGS CAN CAUSE STRANGULATION!

DO NOT PLACE ITEMS WITH STRINGAROUND A CHILD'S NECK, SUCH AS HOODSTRINGS OR PACIFIER CORDS.

DO NOT SUSPEND STRINGS OVER ACRIB OR ATTACH STRINGS TO TOYS.

6

WARNINGDO NOT TIE PACIFIERS, NECKLACES,OR ANY OTHER ITEM AROUND A CHILD'SNECK OR ON THE CRIB PARTS, THISCOULD CAUSE STRANGULATION.

WARNINGNEVER LEAVE YOUR BABY UNATTENDEDWHILE THE CRIB SIDE IS LOWERED!

WARNINGA PERIODIC CHECK SHOULD BE MADE OF ALL SCREWS AND TIGHTEN IF NEEDED.

IMPORTANT FOR YOUR CHILD'SSECURITY

WARNINGANY MATTRESS USED IN THISCRIB MUST BE AT LEAST 27-1/4INCHES BY 51-5/8 INCHES WITH ATHICKNESS NOT EXCEEDING 6INCHES.(MATTRESS TO BE MEASUREDSEAM TO SEAM)

7

HARDWARE DIAGRAM (SCALE 1:1)

EBY2 A

N

D

Q RC

H

G

L M F

O

X Y X1

Y1

A – Screw 12B – Small wrench 1C – Nuts 12D – Plastic round washers 14E – Screw 8F – Screw 2G – Screw 8H – Screw 8L – Screw 4M – Screw 2

N – Screw 2O – Screw 2P – Nuts 2X – Screw 2Y – Screw with pin 2Y2 – Spanner 1Q – Caster stud 4R – Caster (n° 2 with brake) 4X1 – Hole masking cap 4Y1 – Hole masking cap 2

TOOLS REQUIRED FOR ASSEMBLY:METRIC ALLEN WRENCH (INCLUDED)STANDARD SIZE SCREWDRIVER (NOT INCLUDED)HAMMER (NOT INCLUDED)

HARDWARE QUANTITY HARDWARE QUANTITY

P

I M P O R T A N T :

Before commencing assembly,

check that screws E and nuts C screw together

correctly and that pins X and Y

can be inserted into the holes pre-drilled

in the legs (see diagram 6).

If not, please contact your dealer.

(SCALE 1:2)

8

ADDITIONAL PARTS (NOT SCALE DRAWING)

DRAWING QUANTITY DESCRIPTION

Stabilizer bar

Crib spring

Dust cover(thin masonite board)

Crib dropside

Crib headboard left

Crib headboard right

Dropside headboard

Drawer metal guide

2

1

1

1

1

1

1

2

Headboardright

Headboardleft

9

ADDITIONAL PARTS (NOT SCALE DRAWING)

DRAWING QUANTITY DESCRIPTION

Drawerfront

N.B.: The shape of the drawerfront varies depending onthe model.

Drawerback

Drawerleftside

Drawercenter

Drawerrightside

Drawerbottomboard

1

1

1

1

1

2

STEP 1

Unpack and familiarize yourself with all parts andcomponents by comparing them with the pic-tures and descriptions on pages 2, 3, 4.

STEP 2

Note: Some Crib designs are made to be viewedin a certain way.Example: Designs, carvings, moldings, etc... Theoption of mounting the dropside and drawer,allows the decorative view of the crib to be seenproperly and the operational portions (dropsideand drawer) to be where needed. The drawerguides can be mounted two ways. You will needto determine which side the drawer will open andmount the guides accordingly. The wheel in thisguide is where the drawer front will be.This option may not be necessary on all cribs.

Diagram 1

Mounting the drawer guides to the bottom of theheadboard and footboard. Using wrench B,mount the two drawer guides to the bottom ofthe headboard and footboard with screws A (pg.2) in the lowest holes on the inside of the endpanels.Tighten screws.

ONLY FOR “BELLA” CRIB / BEDSTEP 2A Diagram 1A

Before fitting the stabilizer bar to the endpanel (on the side without the leg), insert thebushing (“C”) into the pre-drilled hole (“K”).

STEP 3 Diagram 2

STABILIZER BARS ASSEMBLYAttach stabilizer bars (pg 3) to headboard. Fromthe outside of the headboard insert screws Ewith plastic washers D through holes providedand into stabilizer bar. Insert nut C into stabilizerbar and thread screws E with plastic washers Dinto nuts C. Tighten until snug with wrench F.Repeat for footboard.

STEP 3/A

Lie dust cover (thin masonite board) on top ofdust cover supports, on inside of the stabilizerbars.

10

ASSEMBLY INSTRUCTIONS

AB

A

C

E

B

D

DIAGRAM 1

DIAGRAM 2

C

K

DIAGRAM 1/A

11

STEP 4 Diagram 3

SPRING FRAMETo attach the spring frame, carefully place springframe in the crib so it rests on the stabilizer bars.Attach lower portions of the brackets to stabiliz-er bar using 4 screws H and 4 nuts G. Tightenwith wrench B.

Note: Nuts will be to the inside of the stabilizerbars.

DIAGRAM 3

4

3

2

1

HG

32

1

G

H

DIAGRAM 4

1 LOWEST POSITION

2 MIDDLE POSITION

3 HIGHEST POSITION

STEP 5 Diagram 4

The spring frame has three height positions.Use 4 screws H and 4 nuts G to mount upper armof bracket to desired spring height.

Note: nuts will be to the inside of the springframe.

12

XB

Y

Y2

STEP 7 Diagram 6

Insert screw X into the upper hole in the head-board and tighten fully using wrench B.

Proceed in the same way to insert screw Y intothe lower hole using spanner Y2.

DIAGRAM 6

STEP 6 Diagram 5

DROPSIDE HEADBOARD ASSEMBLYTo assemble the “dropside headboard” to thecrib insert through the holes at the top of the legsthe screw M with the plastic round washer D andscrew with the wrench B.Now insert the screws L with the plastic roundwashers D through the holes at the bottom of thelegs. Insert the nuts C in the panel of the head-board and screw everything with the wrench B.

DIAGRAM 5

L

B D

C

M

B D

13

STEP 8 Diagram 8

FITTING THE DROPSIDEPosition the dropside against the ends of the crib (1). At oneend insert screw X into hole W in the guide (2).Press the other end outwards and repeat the proceduredescrived above. Slide the dropside downwards (3).

DIAGRAM 8

1

3

X

W

2

DIAGRAM 6

INTERNAL SIDE

DIAGRAM 7Diagram 7

Detail of the dropside mechanism.

IMPORTANT:THE DROPSIDE MUST BE FITTED WITH THE

REFERENCE MARKS FACING THE INTERIOR

OF THE CRIB.

14

Step 10 Diagram 11

TO TAKE OFF THE DROPSIDE FROM CRIBFrom the crib side where yu want to take offthe dropside:loosen the screws E with wrench B of only oneheadboard. Do not take off the screws com-pletely.

DIAGRAM 11

Step 9 Diagram 10

HOW TO RAISE AND LOWER DROPSIDE:

To Raise:Hold the dropside in the middle with one hand. Pull sideup firmly until it locks.

To Lower:Hold the dropside in the middle with one hand. Pull sideup lightly but firmly and push lightly but firmly with kneetowards the center of the crib. Lower the side.

1

3

2

DIAGRAM 10

4

5

Y6

DIAGRAM 9Diagram 9

Press the pin of screw Y (4), push the dropside inwards(5) until the pin is inserted into the lower part of theguide.

E

B

D

15

X1

Y1

DIAGRAM 14

5

3

4

X

DIAGRAM 13

12

Y

DIAGRAM 12Step 11 Diagram 12

Pull the leg of this headboard towards outside(1). Catch th dropside at the bottom (2) and letthe pin of screw Y goes out from dropsidemechanism.

Step 12 Diagram 13

Lift up the dropside (3) and let the screw Xgoes out from dropside mechanism.Take off the dropside (4).Tighten again the screw E with the wrench B(5).

Step 13 Diagram 14

MASKING THE HOLES IN THE LEGSUse wrench “B” to remove screws X and thespanner “Y2” for screw Y. Replace the screwswith the masking caps X1 and Y1 as shown indiagram 12.

16

N

B

DIAGRAM 15

DIAGRAM 16

DIAGRAM 17

R

Q

DIAGRAM 18

P

F or O

Rear Side

Step 14 Diagram 15

TO FIX SIDERaise side until it locks. Use 2 screws N to fix side.Tighten screws.

Step 15 Diagram 16

MOUNTING THE CASTERSDO NOT STRIKE THE WHEELS! Place a piece of wood orsomething similar that will fit between the wheels andgently tap with a hammer.

Step 16 Diagram 17

USING THE DROPSIDE HEADBOARD TO BUILD AFULL-SIZE BED

Secure the mattress spring to the dropside head-board with screws A using the four holes with bush-ings located at the base of the legs.

Step 17 Diagram 18

MASKING THE HOLES IN THE TOP OF THE LEGSInsert in rear side of the legs through the holes the screwF (for crib-bed Bella) or O (for crib-bed Alexandra) and infront side of the legs through the holes the nut P; screweverything with the wrench B.

17

M

1

2

2

2

4

4

3M

DRAWER ASSEMBLY INSTRUCTIONS

M

M

5

6

6

7

Step 18 Diagram 19-20

DRAWER ASSEMBLYTurn the metal tabs so they are in theunlocked position (tabs up, diagram 10-1)Attach drawer sides and drawer center todrawerback and push metal tabs down tolock sides and center into place. (diagram14-3) Indert two drawer bottom boards (dia-gram 14-4) into channels.

Step 19 Diagram 21Attach the drawer front to drawer sides andcenter and lock tabs.

Diagram 22Slide drawer into guides on crib end panels.(Wheel to Wheel)

DIAGRAM 19

DIAGRAM 20

DIAGRAM 21DIAGRAM 22

18

Use the page opposite to order spare parts.Simply cut along the dotted line and giveor send the page to your nearest dealer.

19

FOR CRIB MODEL _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ COLOUR _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

LIST OF REPLACEMENT PARTS

1

3

5

4

5

2

711

813

13

12

9

10

6

1

14

Headboard L

Quantity

Headboard R

Quantity

Dropside

Quantity

Dropside/Headboard

Quantity

Spring

Quantity

Drawer bottom board

Quantity

Dust cover

Quantity

Drawer center

Quantity

Drawer right side

Quantity

Drawer left side

Quantity

Drawer front

Quantity

Drawer back

Quantity

Drawer guide right

Quantity

Drawer guide left

Quantity

Stabilizer bar

Quantity

1

2

3

4

13

14

12

11

10

9

8

7

6

5

✃