Upload
others
View
27
Download
1
Embed Size (px)
Citation preview
CP124 CLUTCH PUMP SERIES FEATURESq Cubic inch displacements from 0.62 through 2.48q Speeds to 3000 RPM and pressures to 3500 PSIq SAE “A” mounting with bracket or Pad mounting availableq Heavy duty sleeve bushing design in a small frame sizeq Doweled and high strength 3 piece cast iron constructionq 100% factory testedq High strength alloy steel gear and shaft setq NPT, O’ring, or split fl ange porting located on the rear and/or sideq Only high torque clutches used with all the popular clutch confi gurations availableq Pressure balanced wear plates maintain high pump effi ciency throughout all operating rangesq Typical applications include recovery vehicles, snow plows, spreaders, utility vehicles, winches, small hoists,
aerial devices, lift gates, cranes, and light duty equipment
GEAR DISPL GPM/LITERS MAX MIN MAX WIDTH (IN) CU IN/CC @ 1000 RPM RPM RPM PSI/BAR .50 .62/10 2.2/8.3 3000 600 3500/241 .75 .93/15 3.6/13.6 3000 600 3500/241 1.00 1.24/20 4.9/18.5 3000 600 3500/241 1.25 1.55/25 6.1/23.1 3000 600 3500/241 1.50 1.86/30 7.4/28.0 3000 600 3200/220 1.75 2.17/35 8.8/33.3 3000 600 2900/200 2.00 2.48/40 10.0/37.9 3000 600 2500/172
CP124 with Pad Mounting,
Side and Rear Porting
CP124 CLUTCH PUMPS AND ACCESSORIES
CP124 CLUTCH PUMPS AND ACCESSORIES
CP124 with
Bracket Mount, Side SAE O'ring Ports
CLUTCH PUMP KIT MODEL NUMBER CONSTRUCTIONCLUTCH PUMP KIT MODEL NUMBER CONSTRUCTION
CP124 P 5 B P R A SClutch Pump/Series
MountingB - SAE 2 Bolt A Bracket Mount (Includes Bracket)P - Pad mountN - SAE 2 Bolt A Without Bracket (Pump Only)
RotationR - Right-hand (Clockwise)L - Left-hand (Counter Clockwise)
GPM @ 1000 RPM, at rated PSI2 - .50 inch gear3 - .75 inch gear5 - 1.00 inch gear6 - 1.25 inch gear7 - 1.50 inch gear9 - 1.75 inch gear10 - 2.00 inch gear
Port TypeP - NPTO - O'ringF - Split Flange (Code 61)
B - Both Side and Rear (1 1/4" NPT Inlet, 3/4 " NPT Pressure Standard)R - Rear Only (1 1/4" NPT or O'ring Inlet, 1" NPT or O'ring Pressure)S - Side Only (1 1/4" NPT, O'ring or Split Flange Inlet, 1" NPT, O'ring or Split Flange Pressure)
Port Location
Clutch
Switch Kit
A - 90* lb. ft. AA Groove6 - 90* lb. ft. 6 Groove K Type Serpentine8 - 90* lb. ft. 8 Groove K Type SerpentineX - No Clutch
S - Switch Kit IncludedX - No Switch Kit Included
* After burnishing, see Owner's Manual
2.00/2.48
1.75/2.17
1.50/1.86
1.25/1.55
1.00/1.24
.75/.93
.50/.62
Gear Width/ Cubic Inch Displ.
GPM(at rated PSI)
20
15
10
5
25
30
0
RPM 20001000 1500 2500 3000
CP124 Performance Chart/Specifi cations
Though the pump and clutch will handle these fl ows and pressures, belt slippage may occur.Maximum inlet vacuum should not exceed 5 IN. HG.
2.00/50.80
1.70/43.13
1.16/29.34
Pad Mount Foot Print
7/16 - 14 UNC-28 Thread Thru 2 Places
2.42/61.49
2.00/50.80Optional Side or Rear Only
Port End Cover
2.42/61.49
2.42/61.49
Pad Mount with Dual Ports, AA Groove Clutch
Dimensional Data (inches/mm)
Pad Mount with 6 Groove Serpentine Clutch
Pad Mount with 8 Groove Serpentine Clutch
SAE 2 Bolt A with Bracket, Dual Ports, AA Groove Clutch
SAE 2 Bolt A with Bracket, 6 Groove Serpentine Clutch
SAE 2 Bolt A with Bracket, 8 Groove Serpentine Clutch
Pad Mount Shaft End Cover
4.00/101.60
2.00/50.80
Bracket Mount Foot Print
1/2 Inch Diameter Mounting Holes Thru 4 Places
3.13/79.40
2.28/57.942.81/71.45
2.50/63.50
3/4" NPT Pressure Ports, Side and Rear
Standard
1 1/4" NPT Suction
Ports, Side and Rear Standard
Pad Mount with Dual Ports
3.50/88.90
Port CL
Pulley CL
2.75/69.85
1/4 - 20 UNC-28 Thread Thru 4 Places
1/4 - 20 UNC-28 Thread Thru 4 Places
Bracket Mount
3.50/88.90
Port CL
Pulley CL
2.75/69.85
1.70/43.13
2.28/57.94
2.28/57.94
1.70/43.13 2.75/69.85
2.63/66.68
0.62/15.75
2.42/61.49
4.75/120.65
1.47/37.411.16/29.34
2.42/61.49
2.0/50.80
2.42/61.49
2.35/59.74
6.00/152.40
6.00/152.40
5.47/138.94
Gear Width plus .4/10.16
P - NPT O - O'ring F - Split Flange (Code 61)
Drawings not necessarily to scale. Permco reserves the right to make changes in an ongoing effort to improve the product.
3/8-16 UNC Thread Thru 2 Places
Permco Warranty
Permco1500 Frost Rd.P. O. Box 2068Streetsboro, OH USA 44241Phone 330-626-2801Fax 330-626-2805e-mail [email protected]
Permco Hydraulik AGP. O. Box 553
6343 RotkreuzSwitzerland
Phone +41 (0)41 850 86 65Fax +41 (0)41 850 86 67
e-mail [email protected]© Bulletin #CP12404A
Phone 022-25702597, 98, 99Fax 022-25760830
e-mail [email protected]
Permco (Tianjin) Hydraulic Inc. Ltd.#92 Hai Bin Wu Lu, Freezone
Tianjin Port, China
999-00956 Clutch Pump
Switch Kit
CLUTCH PUMP SERVICE PARTSCLUTCH PUMP SERVICE PARTS
BR549 Clutch Pump Bracket for 2 Bolt "A" Mount
515376 8 Groove Type K
Sepentine Clutch, 90 lb.ft.*
520226 6 Groove Type K
Serpentine Clutch, 90 lb.ft.*
512010 AA Groove Clutch,
90 lb.ft.*
Permco WarrantyPermco warrants that its products will not fail due to defects in materials and workmanship. Failure of any product or any one of its components to perform in accordance with design specifi cations, which failure occurs more than (2) two years or 4,000 hours, whichever is less, from the date of shipment of the product from its point of manufacture, shall be presumed to result from deterioration caused by ordinary use. Permco's obligation in the case of defective workmanship or material is limited to replacement or repair of the defective product, or the defective component therein, at Permco's option, in accordance with the procedures explained herein.
$ This warranty is given in lieu of all other warranties, expressed or implied.
$ There are no warranties which extend beyond the description on the face hereof.
When buyer claims a breach of the limited warranty set forth above, the buyer must notify Permco or its agents promptly, whereupon Permco at its option will either examine the product in question at the site, or issue shipping instructions for its return to Permco or one of its authorized warranty repair centers. Transportation cost must be prepaid by buyer on all returns. Credit for freight in and out, based on surface freight rates will be issued if the inspection of the goods shows a defect in materials or workmanship covered by the limited warranty.
* After burnishing, see Owner's Manual