Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
COURSE HANDOUT
Part-A
PROGRAM : B.Tech., VI-Sem., Civil
ACADEMIC YEAR : 2018-19
COURSE NAME & CODE : Design of Steel Structures (S 185)
L-T-P STRUCTURE : 3-1-0
COURSE CREDITS : 3
COURSE INSTRUCTOR : M.Satyanarayana
COURSE COORDINATOR : M.Satyanarayana
PRE-REQUISITES: EM, SM-I, DRCS -1
COURSE EDUCATIONAL OBJECTIVES (CEOs) :
1. To learn the procedures of limit state design.
2. To develop knowledge in designing of tension members and compression members.
3. To study the built up section in case of heavy loads.
4. To get aware of design of steel beams under various loading conditions economically.
5. To know the design of various types of trusses.
COURSE OUTCOMES (COs):
COURSE ARTICULATION MATRIX (Correlation between COs&POs,PSOs):
COs PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12 PSO1 PSO2 PSO3
CO1 2 2 2 -- -- -- -- -- -- -- -- 1
2 -- 1
CO2 2 2 3 -- -- -- -- -- -- -- -- 1
2 -- 1
CO3 2 2 3 -- -- -- -- -- -- -- -- 1
3 -- 1
CO4 2 2 3 -- -- -- -- -- -- -- -- 1
2 -- 1
CO5 1 2 3 -- -- -- -- -- -- -- -- 1
3 -- 1
Note: Enter Correlation Levels 1 or 2 or 3. If there is no correlation, put ‘-’
1- Slight (Low), 2 – Moderate (Medium), 3 - Substantial (High).
BOS APPROVED TEXT BOOKS:
T1 S.K.Duggal, Design of Steel Structures –Tata McGraw Hill, New Delhi
T2 S.S.Bhavikatti, Design of Steel Structures – I.K.International Publishing House Pvt. Ltd
BOS APPROVED REFERENCE BOOKS:
R1 N.Subramanian, Design of Steel Structures, Oxford University Press
R2 K.S.Sai Ram, Design of Steel Structures, Pearson Education.
R3 Limit State Design of steel structures IS:800-2007-V.L.Shah and Veena Gore Structures
Publications, Jai – Tarang, 30 Parvati, Pune.
Part-B
COURSE DELIVERY PLAN (LESSON PLAN): Section-A/B/C
UNIT-I : Bolted and Welded ConnectionS
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
1. Review for Basics
1 19/11/18
TLM-1 CO 1 T1
2. Introduction to Steel
structures
1
20/11/18
TLM-1
CO 1
T1
3.
Structural steel,
Products of steel
structures
1
24/11/18
TLM-1 CO 1 T1
4.
Standards, codes and
specifications,
Fatigue, Brittle
fracture, corrosion
1
26/11/18
TLM-1 CO 1 T1
5.
Design philosophies,
Methods of structural
analysis
1
27/11/18
TLM-1 CO 1 T1
6.
Plate buckling, classification of
sections, Types of
connections
1
29/11/18
TLM-1 CO 1 T1
7. Tutorial -1
1 01/12/18
TLM-3 CO 1
8. Welded connections
under axial loads
1
03/12/18
TLM-1
CO 1
T1
9. Problems on axial
load 1
04/12/18 TLM-1
CO 1
T1
10. Welded connections under eccentric load
1 06/12/18
TLM-2 CO 1 T1
11. Problems on eccentric
load 1
10/12/18 TLM-2 CO 1 T1
12. Bolted connections, Problems on axial
loads
1 11/12/18
TLM-1 CO 1 T1
13.
Bolted connections
under eccentric load, Problems on Eccentric
load
1
13/12/18
TLM-1 CO 1 T1
14. Tutorial -2
1 15/12/18
TLM-3 CO 1
15. Assignment/Quiz-1 1 15/12/18
TLM-1
No. of classes required to
complete UNIT-I 15 No. of classes taken:
UNIT-II : Compression and Tension Member
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
16.
Introduction to
compression members
1 17/12/18 TLM-1 CO 2 T1
17.
Euler's buckling
theory, Behaviour of
real columns, Types of sections
1 18/12/18 TLM-1 CO 2 T1
18.
Design procedure of
compression
members, Problems on compression
members
1 20/12/18 TLM-1 CO 2 T1
19. Problems on compression
members
1 22/12/18 TLM-1 CO 2 T1
20. Tutorial-3
2 24/12/18 TLM-3 CO 2
21. Design procedure of
tension members 1 27/12/18 TLM-1 CO 2
T1
22. Problems on tension
members 2 29/12/18 TLM-1 CO 2
T1
23. Problems on tension
members 2 31/12/18 TLM-1 CO 2
T1
24.
Tension splices, Design of lug angles,
Problem on lug
angles
1 03/01/19 TLM-1 CO 2
T1
25. Tutorial-4 1 05/01/19 TLM-3 CO 2
T1
26. Quiz-2 1 07/01/19
No. of classes required to
complete UNIT-II 11 No. of classes taken:
UNIT-III : Design Of Lacing ,Batten& Bases
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
follow
ed
HOD
Sign
Week
ly
27.
Design procedure of laced columns,
Problem on laced
columns
1 08/01/19 TLM-1 CO 3
T1
28. Design procedure of battened
columns
1 10/01/19 TLM-1 CO 3
T1
29. Problem on Batten columns
1 12/01/19 TLM-1 CO 3
T1
30. Tutorial-5 1 28/01/19 TLM-3 CO 3
31.
Introduction about
bases, Design of
column bases
1 29/01/19 TLM-1 CO 3
T1
32. Design Procedure of slab bases
1 31/01/19 TLM-1 CO 3
T1
33. Problem on slab
base 1 02/02/18 TLM-1 CO 3
T1
34.
Design Procedure of gusseted base,
Problem on
gusseted base
1 04/02/18 TLM-1 CO 3
T2
35.
Problem on
gusseted base,
Problem on slab
base
1 05/02/18 TLM-1 CO 3
T2
36. Tutorial-6
1 07/02/18 TLM-3 CO 3
37. Quiz-3 1 11/02/18
No. of classes required to
complete UNIT-III 11 No. of classes taken:
UNIT-IV : Design of Beams
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
38.
Behaviour of steel beams
1
12/02/18 TLM-1
CO 4
T1
39.
Limit state of serviceability, Design
procedure of laterally
restrained steel beam
1 14/02/18 TLM-1
CO 4
T1
40. Problems on laterally restrained steel beam
1 16/02/18 TLM-1
CO 4
T1
41. Tutorial-7
1 18/02/18 TLM-3
CO 4
42.
Problems on laterally
restrained steel beam
1 19/02/18 TLM-1
CO 4
T1
43.
Design procedure of
laterally unrestrained
steel beams
1 21/02/18 TLM-1
CO 4
T1
44.
Problems on laterally
unrestrained steel
beam
1 23/02/18 TLM-1
CO 4
T1
45. Problems on laterally unrestrained steel
beam
1 25/02/18 TLM-1
CO 4
T1
46. Lateral torsional buckling of beams
1 26/02/18 TLM-1 CO 4 T1
47. Problem on lateral 2 28/02/18, TLM-1
torsional buckling of beams, Problem on
lateral torsional
buckling of beams
02/03/18
48.
Factors affecting lateral stability,
Problems on laterally
restrained steel beam
1
05/03/18
TLM-1 CO 4 T1
49. Tutorial-8 1 11/03/18 TLM-3 CO 4
50. Quiz-4 1 11/03/18
No. of classes required to complete UNIT-IV
13 No. of classes taken:
UNIT-V : Design Of Roof Trusses and Purlins
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
51.
Design of roof
trusses 1
12/03/18
TLM-1 CO 5 T1
52. Materials of roof trusses, Loads on
roof truss
1 14/03/18
TLM-1 CO 5 T1
53. Design problem on roof trusses
1 16/03/18
TLM-1 CO 5 T1
54. Wind pressure
problems 1
18/03/18 TLM-3 CO 5 T1
55. Tutorial -9 1
19/03/18 TLM-3 CO 5
56. Wind pressure
problems 1
23/03/18 TLM-1 CO 5 T1
57. Design of Purlin Problems
2 25/03/18
TLM-1 CO 5 T1
58. Design of Purlin
Problems 1
26/03/18 TLM-1 CO 5 T1
59. Design of Purlin
Problems 1
28/03/18 TLM-1 CO 5 T1
60. Tutorial -10,
Revision 1
30/03/18 TLM-3 CO 5
No. of classes required to
complete UNIT-V 10 No. of classes taken:
Contents beyond the Syllabus
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
61. Design of roof truss
62. Design of roof
truss
63.
Teaching Learning Methods
TLM1 Chalk and Talk TLM4 Demonstration (Lab/Field Visit)
TLM2 PPT TLM5 ICT (NPTEL/Swayam Prabha/MOOCS)
TLM3 Tutorial TLM6 Group Discussion/Project
Part - C
EVALUATION PROCESS:
Evaluation Task COs Marks
Assignment/Quiz – 1 1 A1=5
Assignment/Quiz – 2 2 A2=5
I-Mid Examination 1,2 B1=20
Assignment/Quiz – 3 3 A3=5
Assignment/Quiz – 4 4 A4=5
Assignment/Quiz – 5 5 A5=5
II-Mid Examination 3,4,5 B2=20
Evaluation of Assignment/Quiz Marks: A=(A1+A2+A3+A4+A5)/5 1,2,3,4,5 A=5
Evaluation of Mid Marks: B=75% of Max(B1,B2)+25% of Min(B1,B2) 1,2,3,4,5 B=20
Cumulative Internal Examination : A+B 1,2,3,4,5 A+B=25
Semester End Examinations 1,2,3,4,5 C=75
Total Marks: A+B+C 1,2,3,4,5 100
Course Instructor Module Coordinator HOD
COURSE HANDOUT
PROGRAM : B.Tech., VI-Sem., CIVIL
ACADEMIC YEAR : 2018-19
COURSE NAME & CODE : GEO TECHNICAL ENGINEERING – II- S256
L-T-P STRUCTURE : 3-1-0
COURSE CREDITS : 3
COURSE INSTRUCTOR : B. NARASIMHA RAO
COURSE COORDINATOR : B. NARASIMHA RAO
PRE-REQUISITE: GEO TECHNICAL ENGINEERING – I
COURSE OBJECTIVE : 1. Understand the principles of soil mechanics.
2. To study the applicable of soil mechanics in design of foundations.
3. Learn the importance of safe bearing capacity of soil for construction purposes. 4. Study about retaining structures design.
COURSE OUTCOMES(CO)
CO1: Understand soil exploration. CO2: Understand role of safe bearing capacity in the construction of foundations and Determine
safe bearing capacity for design of buildings.
CO3: Knowledge about soil structure interaction and group capacity of soils. CO4: Determine the earth pressure and Knowledge about design principles of retaining walls.
CO5: Get information about special foundations and design principles of caissons.
COURSE ARTICULATION MATRIX (Correlation between COs&POs,PSOs):
COs PO
1
PO
2
PO
3
PO
4
PO
5
PO
6
PO
7
PO
8
PO
9
PO
10
PO
11
PSO
1
PSO
2
PSO
3
CO1 3 - - 1 1 1 3 - - - 3 2 1 2
CO2 3 3 - 1 1 1 3 - - - 3 3 1 2
CO3 3 3 - 1 1 1 3 - - - 3 3 1 2
CO4 3 3 3 1 1 1 3 - - - 3 3 1 2
CO5 3 3 - 1 1 1 3 - - - 3 3 1 2
Note: Enter Correlation Levels 1 or 2 or 3. If there is no correlation, put ‘-’
1- Slight(Low), 2 - Moderate(Medium), 3 - Substantial (High).
BOS APPROVED TEXT BOOKS:
T1 Arora K.R, “Soil Mechanics and Foundation Engineering”, Standard Publishers & Distributors, Nai Sarak, Delhi. 1987.
T2
T3
Brahma.S.P, “Foundation Engineering”, Tata McGraw Hill Publishing Co., Ltd., NewDelhi.
1985.
Shamsher Prakash, Swamisaran and Gopal Ranjan , “Analysis and Design of Foundations and
Retaining Structures”, Sarita Prakashan, Meerut, New Delhi. 1987.
BOS APPROVED REFERENCE BOOKS:
R1 Wayne C. Teng, “Foundation Design”, Printice Hall of India Ltd., New Delhi. 1965.
R2 Peck.R.B, Hanson,W.E and Thomburn.T.W, “Foundation Engineering”, John Wiley and Sons, New York. 1974.
COURSE DELIVERY PLAN (LESSON PLAN): Civil
UNIT-I : Site investigation and Selection of foundations
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
1.
Introduction to site
investigation 1 20/11/2018 TLM-1
CO1 T1
2.
Objectives and methods of site
investigation 1 22/11/2018 TLM-1
CO1 T1
3.
Significant depth and depth of
exploration 1 24/11/2018 TLM-1
CO1 T1
4.
Methods of obtaining
undisturbed samples 1 27/11/2018 TLM-4
CO1 T1
5. Standard penetration test
1 28/11/2018 TLM4 CO1 T1
6. Tutorial-1 1 29/11/2018 TLM-3
7. Site investigation report
1 01/12/2018 TLM-1 CO1 T1
8. Types of foundation
1 04/12/2018 TLM-1 CO1 T1
9. Requirements of foundation
1 05/12/2018 TLM-1 CO1 T1
10. Depth of footing
1 06/12/2018 TLM-1 CO1 T1
11. Problems and revision
1 11/12/2018 TLM-4 CO1 T1
12. Tutorial-2
1 12/12/2018 TLM-3 CO1
13. Assignment/Quiz-1 1 12/12/2018 TLM-6 CO1
No. of classes required to complete UNIT-I
10
No. of classes taken:
UNIT-II : Shallow Foundations and Bearing Capacity of Soils
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
14. Introduction to BC of soils
1 13/12/2018 TLM-1 CO2 T1
15.
Terzaghi’s Bearing Capacity
theory and Types of BC
failures 1 15/12/2018 TLM-1
CO2 T1
16.
Meyerhof
BearingCapacitytheory and
factorsaffectingBC of soils 1 18/12/2018 TLM-1
CO2 T1
17.
Differenciate b/w T.B.T and
M.B.T and Problems 1 19/12/2018 TLM-1
CO2
18. Problems 1 20/12/2018 TLM-4 CO2 T1
19. Tutorial-3 1 22/12/2018 TLM-3 T1
20. Plate load test and its limitations
1 26/12/2018 TLM-1 CO2
21. General principal of shallow
foundations 1 27/12/2018 TLM-1
CO2 T1
22. Vibro-flotation methods of improving BC of sandy soils
1 29/12/2018 TLM-1 CO2 T1
23.
Total and Differential
Settlement of foundations in
sand and clays and problems
1 02/01/2019 TLM-4
CO2 T1
24. problems 1 03/01/2019 T1
25. Tutorial-4
1 05/01/2019 TLM-3 CO1
26. Assignment/Quiz-2 1 05/01/2019 TLM-6 CO1
No. of classes required to complete
UNIT-II 10
No. of classes taken:
UNIT-III : Deep Foundations and Group Capacity of Piles
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
27. Introduction to pile foundation
1 29/01/2019 TLM-1 CO3 T3
28. Selection of pile foundation
1 30/01/2019 TLM-1 CO3 T3
29.
Functions of pile foundation
and types of piles 1 31/01/2019 TLM-1
CO3 T3
30.
Pile grouping and Soil
structure interaction 1 02/02/2019 TLM-9
CO3 T3
31.
Pile capacity by static and
dynamic approaches and Problems
1 05/02/2019 TLM-4
CO3 T3
32. Tutorial -5 1 06/02/2019 TLM-3
33. Pile group efficiency
1 07/02/2019 TLM-4 CO3 T3
34. Downward drag phenomenon 1 12/02/2019 TLM-4 CO3 T3
on piles
35.
Pile load test and Impact of
pile driving 1 13/02/2019 TLM-4
CO3 T3
36. Problems
1 14/02/2019 TLM-4 CO3 T3
37. Tutorial -6
1 16/02/2019 TLM-3 CO1
38. Assignment/Quiz-3 1 16/02/2019 TLM-6 CO1
No. of classes required to complete
UNIT-III 09
No. of classes taken:
UNIT-IV : Earth Pressure Theories and Retaining Walls
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
39. Introduction to earth pressure
1 19/02/2019 TLM-1 CO4 T1
40.
Rankine’s earth pressure
theory at rest, active and
passive earth pressure for
cohesive and cohesion less
soils
1 20/02/2019 TLM-1
CO4 T1
41.
coulomb’s earth pressure
theory at rest, active and
passive earth pressure for
cohesive soils
1 21/02/2019 TLM-1
CO4 T1
42. Problems
1 23/02/2019 TLM-4 CO4 T1
43. Tutorial -7 1 26/02/2019 TLM-3
44. Types of retaining walls
1 27/02/2019 TLM-1 CO4 T1
45.
Design of cantilever retaining
walls 1 28/02/2019 TLM-4
CO4 T1
46.
Design of cantilever retaining
walls 1 02/03/2019 TLM-4
CO4 T1
47.
Design of counterfort retaining
walls 1 05/03/2019 TLM-4
CO4 T1
48. Problems
06/03/2019
49. Tutorial-8
1 07/03/2019 TLM-3 CO1 T1
50. Assignment/Quiz-4 1 07/03/2019 TLM-6 CO1 T1
No. of classes required to complete
UNIT-IV 08
No. of classes taken:
UNIT-V : Special Foundations and Stability of slopes
S.No. Topics to be covered No. of Tentative Actual Teaching Learning Text HOD
Classes
Required
Date of
Completion
Date of
Completion
Learning
Methods
Outcome
COs
Book
followed
Sign
Weekly
51.
Necessity and types of
caisson foundation and
Design principles of caisson
foundation
1 12/03/2019 TLM-1
CO5 T3
52.
Foundation in filled up
grounds and Foundation on
expansive soil 1 13/03/2019 TLM-1
CO5 T3
53.
Machine foundation design
principles 1 14/03/2019 TLM-1
CO5 T3
54. Problems
1 16/03/2019 TLM-4 CO5 T3
55. Tutorial -9 1 19/03/2019 TLM-3
56.
Stability analysis of finite
earth slopes and Factors of
safety
1 20/03/2019 TLM-1
CO5 T1
57. Taylor's stability number
1 21/03/2019 TLM-1 CO5 T1
58. Method of slices
1 23/03/2019 TLM-7 CO5 T1
59. Problems
1 26/03/2019 TLM-4 CO5 T1
60. Tutorial -10
1 27/03/2019 TLM-3 CO1
61. Assignment/Quiz-5 1 27/03/2019 TLM-5 CO1
No. of classes required to complete
UNIT-V 08
No. of classes taken:
Contents beyond the Syllabus
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
62. Site investigation (case study) 1 01//01/2019 TLM-9 CO1 T1
63. Theory of vibrations 1 28/03/2019 TLM-1 CO5 T3
64. Stability analysis of infinite earth slopes and Factors of
safety
1 30/03/2019 TLM-1
CO5 T1
Teaching Learning Methods
TLM1 Chalk and Talk TLM4 Problem Solving TLM7 Seminars or GD
TLM2 PPT TLM5 Programming TLM8 Lab Demo
TLM3 Tutorial TLM6 Assignment or Quiz TLM9 Case Study
EVALUATION PROCESS:
Evaluation Task COs Marks
Assignment/Quiz – 1 1 A1=5
Assignment/Quiz – 2 2 A2=5
I-Mid Examination 1,2 B1=20
Assignment/Quiz – 3 3 A3=5
Assignment/Quiz – 4 4 A4=5
Assignment/Quiz – 5 5 A5=5
II-Mid Examination 3,4,5 B2=20
Evaluation of Assignment/Quiz Marks: A=(A1+A2+A3+A4+A5)/5 1,2,3,4,5 A=5
Evaluation of Mid Marks: B=75% of Max(B1,B2)+25% of Min(B1,B2) 1,2,3,4,5 B=20
Cumulative Internal Examination : A+B 1,2,3,4,5 A+B=25
Semester End Examinations 1,2,3,4,5 C=75
Total Marks: A+B+C 1,2,3,4,5 100
Course Instructor Module Coordinator HOD
COURSE
HANDOUT
Part-A
PROGRAM : B.Tech,VI-SEM, Civil
ACADEMIC YEAR : 2018-19
COURSE NAME & CODE : Transportation Engineering -II - S 413
L-T-P STRUCTURE : 3-1-0
COURSE CREDITS : 3
COURSE INSTRUCTOR : M.Manoj kumar
COURSE COORDINATOR : M.Manoj kumar
PRE-REQUISITES: TE-1
COURSE OBJECTIVE: To get acquainted knowledge regarding railway development, planning aspects of
junction and aspects of signaling system and interlocking of railways. To indentify technical aspects of planning, design of airport and water way system.
COURSE OUTCOMES (COs):
CO1 Summarize the rail network development and railway planning in India.
CO2 Analyse different technical aspects of railway junctions.
CO3 Characterise the concepts of railway Interlocking and signalling systems.
CO4 Identify the technical issues related to planning and design of airports
CO5 Illustrate the technical components of harbour.
COURSE ARTICULATION MATRIX (Correlation between COs &POs, PSOs):
COs PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12 PSO1 PSO2 PSO3
CO1 -- -- -- 1 -- -- -- -- -- 1 2 -- 2 1 1
CO2 -- 1 -- 1 -- -- -- -- -- -- 1 -- 1 1 1
CO3 -- -- -- 1 -- -- -- -- -- 1 2 -- 1 1 1
CO4 -- -- -- 1 -- -- -- -- -- 1 2 -- 1 1 1
CO5 -- -- -- 1 -- -- -- -- 1 2 -- 1 1 1
Note: Enter Correlation Levels 1 or 2 or 3. If there is no correlation, put ‘-’
1- Slight (Low), 2 – Moderate (Medium), 3 - Substantial (High).
BOS APPROVED TEXT BOOKS:
1. Saxena.S.C and Arora.S, “A Text Book of Railway Engineering”, Dhanpat Rai Publications
Pvt., Ltd,New Delhi, 2005
2. Bindra.S.P, “A course work in Docks and Harbour Engineering”, Dhanpat Rai Publications
Pvt., Ltd, New Delhi, 2003
3. Khanna,S.K and Arora, M.G & Jain,S.S, “Airport Planning and Design”, New Chand and
Bros, Roorkee, 2001. BOS APPROVED REFERENCE BOOKS:
1. Bindra.S.P, “A course in Bridge, Tunnel and Railway Engineering”, Dhanpat Rai Publications
Pvt., Ltd, New Delhi, 1996
2. Ahuja and Birdi, “Roads, Railways, Bridges and Tunnels Engineering”, Standard Book House,
New Delhi, 2000
3. Srinivasan.R, “Dock, Harbour and Tunnel Engineering”, Charotar Publishing House, Court
Road, Anand, 1989 Part-B
COURSE DELIVERY PLAN (LESSON PLAN):
UNIT- I:
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
1. Course Outcomes Introduction
1 19-11-2018 TLM 1 CO 1 T1
2.
Role of Indian
railways in national
development,
alignments
1 20-11-2018
TLM 1
CO 1
T1
3. Role of remote sensing
1
23-11-2018 TLM 1 CO 1 T1
4.
Permanent way and its
components
Specification of
gauges
2
24-11-2018,
26-11-2018 TLM 1 CO 1 T1
5. Ballast ,sleepers 1 27-11-2018 TLM 1 CO 1 T1
6. TUTORIAL-1 1 30-11-2018 TLM 3 CO 1
7. Construction of
railway track
1
1-12-2018
TLM 1
CO 1
T1
8. Renewal and
maintenance
2
3-12-2018
4-12-2018
TLM 1
CO 1
T1
9. Rail joints 1 7-12-2018 TLM 1 CO 1 T1
10. Welding of railways 1 8-12-2018 TLM 1 CO 1 T1
11. TUTORIAL-2 1 10-12-2018 TLM 3 CO 1 T1
No. of classes required to
complete UNIT-I 12 No. of classes taken:
UNIT-II:
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
12.
Introduction to
track junctions 1 11-12-2018 TLM 1 CO 2 T1
13. Points or switches 2 14-12-2018
15-12-2018 TLM 1 CO 2 T1
14. Crossings or
turnouts 2
17-12-2018
18-12-2018 TLM 1 CO 2 T1
15. Devices and layouts 1 21-12-2018 TLM 1 CO 2 T1
16.
Most commonly
used layout of track
junctions
2 22-12-2018 TLM 1 CO 2
T1
17. Special fittings,
Safety devices 1 24-12-2018 TLM 1
T1
18. TUTORIAL-3 2 28-12-2018 TLM 3 CO 2 T1
19. Station ,yards and
their layout 2 29-12-2018 TLM 1 CO 2
T1
20.
General
equipment’s in
railways
1 31-12-2018 TLM 1 CO 2
T1
21. Track junctions 1 1-01-2019 TLM 1 CO 2 T1
22. TUTORIAL-4 1 4-01-2019 TLM 3 T1
No. of classes required to
complete UNIT-II 16 No. of classes taken:
UNIT-III :
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
23.
Signals and their
types and working
principles
1 5-01-2019 TLM 1 CO 3
T1
24. Principles of
interlocking 1 7-01-2019 TLM 1 CO 3
T1
25. Types of
interlocking 1 8-01-2019 TLM 1 CO 3
T1
26. TUTORIAL-5
1 11-01-2019 TLM 3 CO 3
T1
27. Safety devices in
signals 1 12-01-2019 TLM 1 CO 3
T1
28. Control systems
on trains 1 25-01-2019 TLM 1 CO 3
T1
29. Modern trends in
Indian railways 1 26-01-2019 TLM 1 CO3
T1
30. suburban railways,
Electric traction 1 28-01-2019 TLM 1 CO 3
T1
31.
Design adopted
for high speed
tracks
1 29-01-2019 TLM 1 CO 3
T1
32. MRTS suburban
railways 1 1-02-2019 TLM 1 CO 3
T1
33. TUTORIAL-6 1 2-02-2019 TLM 3 CO 3
T1
34.
High speed trains,
BOT and BOLT
concepts
1 4-02-2019 TLM 1
CO3
T1
No. of classes required to complete UNIT-III
12 No. of classes taken:
UNIT-IV:
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
35. Introduction to
Airport engineering
1
5-02-2019
TLM 1
CO 4
T3
36. Airport planning 1 8-02-2019
TLM 1
CO 4
T3
37.
Standards for
planning of airports
as per ICAO,
1
9-02-2019
TLM 1
CO 4
T3
38. Airport zoning and
runway orientation
1 11-02-2019 TLM 1
CO4 T3
39. Site selection survey
1
12-02-2019 TLM 1
CO 4
T3
40. Geometric design
elements
1
15-02-2019 TLM 1
CO 4
T3
41.
Different types,
patterns and layout of
taxiways
1
16-02-2019
TLM 1
CO 4
T3
42. Aprons and holding
aprons
1 18-02-2019 TLM 1
CO4 T3
43. Planning and layout
of terminal buildings
1
19-02-2019
22-02-2019
TLM 1
CO 4
T3
44. TUTORIAL-7 1 23-02-2019 TLM 3 CO 4 T3
45. Hangars and parking area
1 25-02-2019 TLM 1
CO 4 T3
46. TUTORIAL-8 1 26-02-2019 TLM 3 CO 4 T3
47. Assignment/Quiz-4 1 1-03-2019 TLM 1 CO 4 T3
No. of classes required to
complete UNIT-IV 13 No. of classes taken:
UNIT-V:
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
48.
Introduction to ports
and harbours,
classification
1 2-03-2019 TLM 1 CO 5 T2
49. Wind and waves
concept 1 4-03-2019 TLM 1 CO 5 T2
50. Hydro graphic
surveying 1 5-03-2019 TLM 1 CO5 T2
51. Components of
harbour 2 8-03-2019
9-03-2019 TLM 1 CO 5 T2
52. TUTORIAL-9 1 11--03-2019 TLM 3 CO 5 T2
53. Docks and types of
docks 1 12-03-2019 TLM 1 CO5 T2
54. Terminal building 1 15-03-2019 TLM 1 CO5 T2
55. navigational aids 1 16-03-2019 TLM 1 CO 5 T2
56. signals 1 18-03-2019 TLM 1 CO5 T2
57. Dredging methods 1 19-03-2019 TLM 1 CO 5 T2
58. Dredger equipments 1 22-03-2019 TLM 1 CO5 T2
59. TUTORIAL-10 1 23-03-2019 TLM 3 CO5 T2
60. Assignment/Quiz-5 1 25-03-2019 CO5 T2
No. of classes required to
complete UNIT-V 14 No. of classes taken:
Contents beyond the Syllabus
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
61. Geometric design of
railway track
3 26-03-2019 29-03-2019
30-03-2019
CO2 T1
Teaching Learning Methods
TLM1 Chalk and Talk TLM4 Demonstration (Lab/Field Visit)
TLM2 PPT TLM5 ICT (NPTEL/Swayam Prabha/MOOCS)
TLM3 Tutorial TLM6 Group Discussion/Project
Part – C
EVALUATION PROCESS:
Evaluation Task COs Marks
Assignment/Quiz – 1 1 A1=5
Assignment/Quiz – 2 2 A2=5
I-Mid Examination 1,2 B1=20
Assignment/Quiz – 3 3 A3=5
Assignment/Quiz – 4 4 A4=5
Assignment/Quiz – 5 5 A5=5
II-Mid Examination 3,4,5 B2=20
Evaluation of Assignment/Quiz Marks: A=(A1+A2+A3+A4+A5)/5 1,2,3,4,5 A=5
Evaluation of Mid Marks: B=75% of Max(B1,B2)+25% of Min(B1,B2) 1,2,3,4,5 B=20
Cumulative Internal Examination : A+B 1,2,3,4,5 A+B=25
Semester End Examinations 1,2,3,4,5 C=75
Total Marks: A+B+C 1,2,3,4,5 100
Course Instructor Module Coordinator HOD
COURSE HANDOUT
PROGRAM : B.Tech., VI-Sem., CIVIL
ACADEMIC YEAR : 2018-19
COURSE NAME & CODE : Water Resources Engineering (S421)
L-T-P STRUCTURE : 3-1-0
COURSE CREDITS : 3
COURSE INSTRUCTOR : J.Rangaiah
COURSE COORDINATOR : J.Rangaiah
PRE-REQUISITE : Applied Mechanics, Mechanics of Fluids,
Hydraulics and Hydraulic Machinery, Hydrology
COURSE OBJECTIVE : 1. Learn the concept of reservoir planning and importance of reservoir sedimentation.
2. Study the gravity and earth dams and perform their stability analysis.
3. Learn the various types of head works constructed at the head of the canal and types and
different components and their purposes.
4. Identify canal regulation structures and cross drainage structures featuring in the alignment of
the channels.
5. Know about classification of canals and design irrigation canals by Kennedys and Laceys
theories
COURSE OUTCOMES (CO) :
CO1: Understand importance of reservoir sedimentation in planning for water resources.
CO2: Perform stability analysis for gravity and earth dams.
CO3: Analyze the parameters needed in the design of weirs/barrages in permeable soils.
CO4: Design the irrigation canals, canal regulation structures and cross drainage structures.
CO5: Design canals using existing theories.
COURSE ARTICULATION MATRIX (Correlation between COs&POs,PSOs):
COs PO
1
PO
2
PO
3
PO
4
PO
5
PO
6
PO
7
PO
8
PO
9
PO
10
PO
11
PO
12
PSO
1
PSO
2
PSO
3
CO1
2 2 2 3 1 2 2 2 2 1 1
CO2
2 2 2 3 1 2 2 2 2 1 2
CO3
3 2 3 3 2 2 2 2 2 3 2 1 2
CO4
3 2 2 3 2 3 2 2 3 2 3 2 3
CO5
3 2 3 2 3 2 2 2 2 2 3 2 3
Note: Enter Correlation Levels 1 or 2 or 3. If there is no correlation, put ‘-’ 1- Slight(Low), 2 - Moderate(Medium), 3 - Substantial (High).
BOS APPROVED TEXT BOOKS:
T1 Santhosh Kumar Garg, “Irrigation Engineering and Hydraulic Structures,” Khann
Publishers, New Delhi, 2003
T2
Punmia.B.C, “Irrigation and Water Power Engineering,” Standard Publishers, New Delhi, 1997.
BOS APPROVED REFERENCE BOOKS:
R1
R2
R3
Michael A.M., “Irrigation – Theory and Practice”, Vikas Publishing House, New Delhi, 1990.
Sharma R.K., “Irrigation Engineering and Hydraulic Structures”, Oxford and IBH Publishing company, New Delhi, 1994.
Dilip Kumar Majumdar, “Irrigation Water Management Principles and Practice”, Prentice –
Hall of India, Private Limited, New Delhi, 2000.
R4 Modi.P.N., “Irrigation Water Resources and Water Power Engineering”, Standard Book House, Delhi, 1995.
COURSE DELIVERY PLAN (LESSON PLAN): Civil
UNIT-I RESERVOIR PLANNING & DAMS
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
1.
Types of reservoirs,
Selection of
site for
reservoir
1 19/11/18 TLM-1 CO1 T2
2.
Zones of
storage of a
reservoir, reservoir
yield
1 20/11/18 TLM-1 CO1 T2
3.
Estimation of
capacity of reservoir
using mass
curve
1 21/11/18 TLM-1 CO1 T2
4. Problems on reservoir
capacity
1 23/11/18 TLM-4 CO1 T2
5. Reservoir sedimentation
1 26/11/18 TLM-1 CO1 T2
6. Tutorial-1 1 27/11/18 TLM-3 CO1
7.
Types of
dams, Merits
and demerits of varies
types of dams
1 28/11/18 TLM-1 CO1 T2
8.
Factors
affecting selection of
type of dam,
1 30/11/18 TLM-1 CO1 T2
9. Quiz-1 1 03/12/18 TLM-6 CO1 T2
10.
Factors
governing selecting site
for dam
1 04/12/18 TLM-1 CO1 T2
11. Tutorial-2 1 05/12/18 TLM-3 CO1 T2
No. of classes
required to complete UNIT-II
10
No. of classes taken:
UNIT-II GRAVITY DAMS & EARTH DAMS
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
12.
Forces acting on a gravity
dam, Causes of
failure of a gravity dam
1 07/12/18 TLM-1 CO2 T1
13.
Elementary
profile and
practical profile of a gravity
dam, Limiting
height of a low gravity dam
1 10/12/18 TLM-1 CO2 T1
14. Stability
analysis 1 11/12/18 TLM-1 CO2 T1
15. Problems on stability
analysis
1 12/12/18 TLM-4 CO2 T1
16. Drainage
galleries. 1 14/12/18 TLM-1 CO2 T1
17. Tutorial-3 1 17/12/18 TLM-3 CO2
18.
Types &
Causes of
failure of earth
dam
1 18/12/18 TLM-2 CO2 T2
19.
Criteria for safe
design of earth
dam,
1 19/12/18 TLM-1 CO2 T2
20.
Seepage through earth
dam, Graphical
method
1 21/12/18 TLM-1 CO2 T2
21.
Measures for
control of
seepage.
1 24/12/18 TLM-1 CO2 T2
22. Spillways: types of
spillways
1 26/12/18 TLM-1 CO2 T2
23.
Design principles of
Ogee spillways,
Types of
spillway gates
1 28/12/18 TLM-1 CO2 T2
24. Tutorial-4 1 31/12/18 TLM-3 CO2
No. of classes required
to complete UNIT-II 13
No. of classes taken:
UNIT-III : DIVERSION HEAD WORKS
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
25.
Types of
Diversion head
works, Layout of
diversion head works
1 25/01/18 TLM-1 CO3 T2
26.
Causes and
failure of hydraulic
structures on
permeable
foundations
1 28/01/18 TLM-1 CO3 T2
27. Bligh’s creep
theory 1 29/01/18 TLM-1 CO3 T2
28. Problems 1 30/01/18 TLM-4 CO3 T2
29. Khosla’s theory 1 01/02/18 TLM-1 CO3 T2
30. Problems 1 04/02/18 TLM-4 CO3 T2
31. Tutorial-5 1 05/02/18 TLM-3 CO3
32. Determination of
uplift pressure 1 06/02/18 TLM-1 CO3 T2
33. Impervious floors using Bligh’s
theory
1 08/02/18 TLM-1 CO3 T2
34.
Impervious floors
using Khosla’s theory
1 11/02/18 TLM-1 CO3 T2
35.
Exit gradient,
Functions of U/s
and d/s sheet piles.
1 12/02/18 TLM-1 CO3 T2
36. Tutorial-6 1 13/02/18 TLM-3 CO3
No. of classes required to
complete UNIT-III 12
No. of classes taken:
UNIT-IV : CANALS AND CANAL STRUCTURES
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
37.
Canals:
Classification
of canals
1 15/02/18 TLM-1 CO4 T1
38.
Design of
canals by
Kennedy’s
theories
1 18/02/18 TLM-1 CO4 T1
39.
Design of
canals by
Lacey’s
theories
1 19/02/18 TLM-1 CO4 T1
40.
Balancing
depth of
cutting, Canal
lining,
1 20/02/18 TLM-1 CO4 T1
41.
design of lined
canal,
Economics of
canal lining
1 22/02/18 TLM-1 CO4 T1
42. Tutorial-7 1 25/02/18 TLM-3 CO4
43. Canal
structures 1 26/02/18 TLM-1 CO4 T1
44.
Types of falls
and their
location
1 27/02/18 TLM-1 CO4 T1
45.
Design
principles of
Sarda type fall
1 01/03/18 TLM-1 CO4 T1
46.
Design
principles of
trapezoidal
notch fall
1 05/03/18 TLM-1 CO4 T1
47.
Design
principles of
straight glacis
fall.
1 06/03/18 TLM-1 CO4 T1
48. Tutorial-8 1 08/03/18 TLM-3 CO4
No. of classes required
to complete
UNIT-IV
12
No. of classes taken:
UNIT-V CANAL REGULATION WORKS & CROSS DRAINAGE WORKS
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
49.
Head regulator
and cross
regulator
1 11/03/18 TLM-1 CO5 T1
50.
Design
principles of
cross regulator
1 12/03/18 TLM-1 CO5 T1
51.
Design
principles of
head regulators
1 13/03/18 TLM-1 CO5 T1
52.
Canal outlets,
types of canal
modules
1 15/03/18 TLM-1 CO5 T1
53.
Proportionality,
sensitivity and
flexibility
1 18/03/18 TLM-1 CO5 T1
54. Tutorial-9 1 19/03/18 TLM-3 CO5
55.
Types, selection
of site for Cross
Drainage works
1 19/03/18 TLM-1 CO5 T1
56.
Design
principles of
aqueduct
1 22/03/18 TLM-1 CO5 T1
57.
Design
principles of
siphon aqueduct
1 25/03/18 TLM-1 CO5 T1
58. Tutorial-10 1 26/03/18 TLM-3 CO5
No. of classes required to complete
UNIT-V
10
No. of classes taken:
Contents beyond the Syllabus
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
59.
60.
61.
Teaching Learning Methods
TLM1 Chalk and Talk TLM4 Problem Solving TLM7 Seminars or GD
TLM2 PPT TLM5 Programming TLM8 Lab Demo
TLM3 Tutorial TLM6 Assignment or Quiz TLM9 Case Study
ACADEMIC CALENDAR
Description From To Weeks
I Phase of Instructions 19-11-18 12-01-19 7W
I Mid Examinations 18-01-19 24-01-19 1W
II Phase of Instructions 25-01-19 30-03-19 9W
II Mid Examinations 01-04-19 06-04-19 1W
Preparation and Practicals 08-04-19 20-04-19 2W
Semester End Examinations 22-04-19 04-05-19 2W
EVALUATION PROCESS
Evaluation Task COs Marks
Assignment/Quiz – 1 1 A1=5
Assignment/Quiz – 2 2 A2=5
I-Mid Examination 1,2 B1=20
Assignment/Quiz – 3 3 A3=5
Assignment/Quiz – 4 4 A4=5
Assignment/Quiz – 5 5 A5=5
II-Mid Examination 3,4,5 B2=20
Evaluation of Assignment/Quiz Marks: A=(A1+A2+A3+A4+A5)/5 1,2,3,4,5 A=5
Evaluation of Mid Marks: B=75% of Max(B1,B2)+25% of Min(B1,B2) 1,2,3,4,5 B=20
Cumulative Internal Examination : A+B 1,2,3,4,5 A+B=25
Semester End Examinations 1,2,3,4,5 C=75
Total Marks: A+B+C 1,2,3,4,5 100
Course Instructor
Course Coordinator
Module Coordinator
HOD
COURSE HANDOUT
PROGRAM : B.Tech., VI-Sem., CE
ACADEMIC YEAR : 2018-19
COURSE NAME & CODE : Waste Water Engineering - S 420
L-T-P STRUCTURE : 3-1-0
COURSE CREDITS : 3
COURSE INSTRUCTOR : Dr V. Ramakrishna
COURSE COORDINATOR : Dr V. Ramakrishna
PRE-REQUISITE: Nil
COURSE OBJECTIVES:
1. To estimate the quantity of sewage generation and design the sewers
2. To analyze the impacts of wastewater quality parameters on environment
3. To select and design the wastewater treatment systems based on quality parameters
4. To choose the appropriate sludge handling and sewage disposal options.
5. To identify the sewer appurtenances used in sewerage system and the plumbing systems.
COURSE OUTCOMES (CO):
CO1: Describe the sanitation systems, estimate the sewage generation and design the sewers.
CO2: Interpret the impact of wastewater quality parameters on receptors
CO3: Design the wastewater treatment systems
CO4: Design the sludge handling systems
CO5: Analyze the various sewer appurtenances used in the sewerage system and plumbing systems
for their application in field.
COURSE ARTICULATION MATRIX (Correlation between COs & POs, PSOs):
COs PO
1
PO
2
PO
3
PO
4
PO
5
PO
6
PO
7
PO
8
PO
9
PO
10
PO
11
PO
12
PSO
1
PSO
2
PSO
3
CO1 1 2 2 - - 1 - - - - - 1 2 - -
CO2 2 1 - - - 2 - - - - - 1 - 2 -
CO3 2 2 3 - - - - - - - - 1 3 - 2
CO4 2 2 3 - - - - - - - - 1 3 - 2
CO5 - 1 - - - 1 1 - - - - 1 - - 1
Note: Enter Correlation Levels 1 or 2 or 3. If there is no correlation, put ‘-’
1- Slight (Low), 2 – Moderate (Medium), 3 - Substantial (High).
BOS APPROVED TEXT BOOKS:
T1 Garg.S.K, “Sewage disposal and Air Pollution Engineering”, Khanna Publishers New
Delhi. 2001. T2 Punmia B.C, Jain and Jain, “Waste water Engineering”, Laxmi Publications, New Delhi, 1998.
BOS APPROVED REFERENCE BOOKS:
R1 Birdie G.S, Birdie J.S, “Water Supply and Sanitary Engineering”, Dhanpat Rai Publishing
Company, New Delhi, 1998.
R2 Modi P.N. “Sewage Disposal and Air pollution Engineering”, Standard Publishing House, 2015.
R3 Manual on sewerage and sewage treatment, CPHEEO, Ministry of urban affairs and
employment, Govt. of India, New Delhi, 2001.
COURSE DELIVERY PLAN (LESSON PLAN)
UNIT-I: SANITATION SYSTEMS AND SEWER DESIGN
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
1. Introduction and Sanitation 1 20.11.18 27.11.18 1 CO1 _
2. Basic definitions, Systems of
sanitation 1 22.11.18 28.11.18 1
CO1 T2
3. Storm water estimation 1 24.11.18 1 CO1 T2
4. Flow rates, Sewer design 1 27.11.18 1 CO1 T2
5. Problems 1 28.11.18 1 CO1 T2
6. Problems/Tutorial-1 1 29.11.18 1 CO1 T2
7. Storm drains, Problems 1 1.12.18 4 CO1 T1, T2
8. Problems/ Tutorial-2 1 4.12.18 1,4 CO1 T1, T2
9. Assignment/Quiz-1
1 5.12.18 1 CO1 T1, T2,
R2
No. of classes required to complete
UNIT-I 8
No. of classes taken:
UNIT-II: SEWAGE QUALITY PARAMETERS AND SELF PURIFICATION OF RIVERS
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
1. Sewage Quality, Decomposition cycles
1 6.12.18 1 CO2 T2
2. Physical parameters, Problems 1 8.12.18 1 CO2 T2
3. Chemical parameters, BOD 1 11.12.18 1 CO2 T2
4. BOD Equation 1 12.11.18 1 CO2 T2
5. Problems 1 13.12.18 4 CO2 T1, T2
6. Dilution factor 1 15.12.18 1 CO2 T2
7. DO Model 1 18.12.18 4 CO2 T1, T2
8. Problems/ Tutorial-3 1 19.12.18 4 CO2 T1, T2
9. Zones of Pollution 1 20.12.18 3 CO2 T1, T2, R2
10. COD & other parameters 1 22.12.18 1 CO2 T1, T2, R2
11. Problems/ Tutorial-4 1 26.12.18 1 CO2 T2
12. Assignment/Quiz 1 27.12.18 1 CO2 T2
No. of classes required to complete
UNIT-II 12
No. of classes taken:
Mid-I Exam: Jan 18-24, 2019
UNIT-III: DESIGN OF SEWAGE TREATMENT UNITS
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text Book
followed
HOD
Sign
Weekly
1. Sewage treatment basics 1 29.12.18 1 CO3 T2
2. Screens, Grit channel 1 2.1.19 1 CO3 T2
3. Skimming tank, Primary
clarifier 1 3.1.19 1
CO3 T2
4. Aeration system basics 1 5.1.19 1 CO3 T1,T2
5. ASP parameters 1 8.1.19 1 CO3 T2
6. Complete mix process- Design 1 9.1.19 1 CO3 T2
7. Diffused aeration process - Design
1 10.1.19 4 CO3 T1, T2
8. Revision of design systems 1 12.1.19 4 CO3 T1, T2
9. Tutorial-5 1 29.1.19 3 CO3 T1, T2, R2
10. Secondary clarifier 1 30.1.19 1 CO3 T1, T2
11. Problems 1 31.1.19 4 CO3 T2
12. Ponds 1 2.2.19 1 CO3 T1, T2
13. Problems 1 5.2.19 4 CO3 T2
14. Oxidation ditch, Revision 1 6.2.19 2 CO3 T1, T2
15. Tutorial-6 1 7.2.19 3 CO3 T1, T2, R2
16. Assignment/Quiz-3 1 9.2.19 6 CO3 T1, T2, R2
No. of classes required to complete
UNIT-III 16
No. of classes taken:
UNIT-IV: SEWAGE TREATMENT AND SLUDGE HANDLING TECHNIQUES
S.No. Topics to be cover1ed
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text Book
followed
HOD
Sign
Weekly
1. Trickling filter 1 12.2.19 2 CO3 T2
2. Types of filters 1 13.2.19 2 CO3 T2
3. Problems 1 14.2.19 4 CO3 T1, T2
4. Sludge handling basics 1 16.2.19 1 CO4 T2
5. Problems 1 19.2.19 4 CO4 T1, T2
6. Tutorial-7 1 20.2.19 3 CO4 T1, T2, R2
7. Sludge digestion 1 21.2.19 2 CO4 T1
8. Problems 1 23.2.19 4 CO4 T1
9. Sludge drying beds 1 26.2.19 1 CO4 T1, T2
10. Sludge processing techniques 1 27.2.19 2 CO4 T2, T1
11. Septic tank 1 28.2.19 2 CO3 T2
12. Tutorial-8 1 2.3.19 3 CO4 T1, T2, R2
13. Assignment/Quiz-4 1 5.3.19 6 CO3/4 T1, T2, R2
No. of classes required to complete
UNIT-IV 13
No. of classes taken:
UNIT-V: SEWER APPURTENANCES AND PLUMBING SYSTEMS
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text Book
followed
HOD
Sign
Weekly
1. Sewer appurtenances 1 6.3.19 2 CO5 T2
2. Traps and pipes, Sewage disposal
1 7.3.19 2 CO5 T2
3. Sewer materials 1 9.3.19 2 CO4 T2
4. Forces on sewers 1 12.3.19 2 CO5 T2
5. Rural sanitation/Tutorial 1 13.3.19 2 CO5 T2
6. Assignment/Quiz-5 1 14.3.19 6 CO5 T2
No. of classes required to complete UNIT-V
6
No. of classes taken:
Mid-II Exam: Apr 1-6, 2019
CONTENTS BEYOND THE SYLLABUS
S.No. Topics to be covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
7. Industrial wastewater treatment 1 16.3.18 2/9 1-5 T1, T2
Teaching Learning Methods
TLM1 Chalk and Talk TLM4 Problem Solving TLM7 Seminars or GD
TLM2 PPT TLM5 Programming TLM8 Lab Demo
TLM3 Tutorial TLM6 Assignment or Quiz TLM9 Case Study
EVALUATION PROCESS
Evaluation Task COs Marks
Assignment/Quiz – 1 1 A1=5
Assignment/Quiz – 2 2 A2=5
I-Mid Examination 1,2 B1=20
Assignment/Quiz – 3 3 A3=5
Assignment/Quiz – 4 4 A4=5
Assignment/Quiz – 5 5 A5=5
II-Mid Examination 3,4,5 B2=20
Evaluation of Assignment/Quiz Marks: A= (A1+A2+A3+A4+A5)/5 1,2,3,4,5 A=5
Evaluation of Mid Marks: B = 75% of Max (B1, B2) + 25% of Min (B1,B2) 1,2,3,4,5 B=20
Cumulative Internal Examination : A+B 1,2,3,4,5 A+B=25
Semester End Examinations 1,2,3,4,5 C=75
Total Marks: A+B+C 1,2,3,4,5 100
COURSE HANDOUT
Part-A
PROGRAM : B.Tech., VI-Sem., Civil
ACADEMIC YEAR : 2018-19
COURSE NAME & CODE : Repair and Rehabilitation of Structures – S437
L-T-P STRUCTURE : 3-1-0
COURSE CREDITS : 3
COURSE INSTRUCTOR : K. Harish Kumar
COURSE COORDINATOR :
PRE-REQUISITES : Reinforced Concrete Elements, Building materials and
Concrete technology.
COURSE EDUCATIONAL OBJECTIVES (CEOs) :
1. To understand the various types of cracks and maintenance in R.C and masonry
structures.
2. To identify requirements of serviceability and durability in concrete.
3. To understand the various types of repairing materials to regain its strength.
4. To identify the damages of the structures by Non-destructive testing.
5. To understand the various techniques of rehabilitation of structures.
COURSE OUTCOMES (COs):
CO1: Understand the various types of cracks and maintenance in R.C and masonry Structures.
CO2:Identifyrequirementsofserviceabilityanddurabilityinconcrete.
CO3:Understandthevarioustypesofrepairingmaterialstoregainitsstrength.
CO4:IdentifythedamagesofthestructuresbyNon-destructivetesting.
CO5: Understand the various techniques of rehabilitation of structures.
COURSE ARTICULATION MATRIX (Correlation between COs&POs,PSOs):
COs PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12 PSO1 PSO2 PSO3
CO1 3 - 1 3 1 - 1 - - 2 2 - 2 1 1
CO2 2 - 2 3 2 - 1 - - - 1 - 3 1 2
CO3 2 2 2 3 2 2 2 - - - 1 - 3 3 1
CO4 2 3 3 3 2 - 1 - - - 1 - 3 2 1
CO5 3 1 2 3 2 - 3 - - 2 1 - 3 3 1
Note: Enter Correlation Levels 1 or 2 or 3. If there is no correlation, put ‘-’
1- Slight (Low), 2 – Moderate (Medium), 3 - Substantial (High).
BOS APPROVED TEXT BOOKS:
T1-Noel P. Mailvaganam, “Repair and protection of concrete structures” CRC press,
London.
T2-Pankaj Agarwal and Manish Shrikande, “Earthquake resistant design of
structures”, PHI.
T3-R.T. Allen and S.C. Edwards, “Repair of concrete structures”, Blakie and sons,
UK,1987.
T4-Peter.H.Emmons, “Concrete repair and maintenance illustrated” Galgotia
publishers.
BOS APPROVED REFERENCE BOOKS:
R1 Champion, “Failures and repair of concrete structures” John Wilesy and Sons.
R2 “Handbook on repair and rehabilitation of RCC buildings”, CPWD, India.
R3 R.N. Raikar, “Diagnosis and treatment of structures in distress”
Published by R & D centre of structural designers and consultants Pvt.ltd,
Mumbai.
R4 “Handbook on seismic retrofit of buildings”, CPWD, Indian buildings congress,
IIT Madras, Narosa Publishing House.
Part-B
COURSE DELIVERY PLAN (LESSON PLAN): Section-A/B/C
UNIT-I : Cracks and Maintenance
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
64.
Introduction to CO & POs & Introduction to rehabilitation of structures and its need
2
19/11/18 21/11/18
TLM-1
CO1
R2
65.
Introduction to Maintenance, rehabilitation, repair, retrofit and strengthening
1 22/11/18
TLM-1
CO1
R4
66.
Importance of maintenance and different kinds of maintenance
1
24/11/18
TLM-1 CO1 T4
67.
Various cracks in R.C buildings, causes and its effects.
1
26/11/18
TLM-1,2 CO1 R4
68. Tutorial -1 1 28/11/18
TLM-3
69.
Various damages to masonry structures and causes
1
29/11/18
TLM-1 CO1 R1
70.
Step by step procedure to damages of structures
2 01/12/18 03/12/18
TLM-1 CO1 R4
71. Tutorial -2
1 05/12/18
TLM-3
72. Assignment/Quiz-1
No. of classes required to
complete UNIT-I 10 No. of classes taken:
UNIT-II : Serviceability and durability of concrete
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
73.
Introduction to
concrete
properties
1 06/12/18
TLM-1 CO2 R4
74.
Quality
assurance for
concrete
construction
1 10/12/18
TLM-1 CO2 R4
75.
Concrete
properties-
Strength,
permeability,
thermal
properties and
cracking.
2
12/12/18
13/12/18
TLM-
1,2
CO2
R1
76. Tutorial-3 1 15/12/18 TLM-3
77.
Effects due to
climate,
temperature &
chemicals
2
17/12/18
19/12/18
TLM-1
CO2
R2
78.
Effects due to
corrosion
design and
construction
errors
2
20/12/18
22/12/18
TLM-1
CO2
R1
79.
Effects of cover
thickness and
cracking
1 24/12/18
TLM-1 CO2 R1
80. Tutorial-4 1 26/12/18
TLM-3 CO2 R4
81.
Revision on
1st& 2nd Units 1
27/12/18
CO2 R4
82. Assignment/Quiz
-2
No. of classes required to complete UNIT-II
12 No. of classes taken:
UNIT-III : Repair and grouting materials
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
follow
ed
HOD
Sign
Week
ly
83. Introduction 1 29/12/18 TLM-1 CO3 T1
84.
Various repair
materials,
criteria for
material
selection
2
31/12/18
02/01/19
TLM-1,2
CO3 T1
85.
Methodology of
selection, health
and safety
precautions for
handling
2
03/01/19
05/01/19
TLM-1
CO3 R4
86.
Applications of
repair materials
and polymer
concrete
1
07/01/19
TLM-1
CO3 R4
87.
Motor concrete
and quick setting
compounds
2
09/01/19
10/01/19
TLM-1,2
CO3 R1
88. Tutorial-5 1 12/01/19 TLM-3
89.
Grouting
materials: Gas
forming grouts,
polymer grouts
2
30/01/19
31/01/19
TLM-1,2
CO3 R2
90.
Salfoalumate
grouts,
acrylate and
urethane grouts
1
02/02/19
TLM-1,2
CO3 R2
91.
Bonding
agents: Latex
emulsions,
epoxy bonding
agents
2
04/02/19
06/02/19
TLM-1,2
CO3 R4
92.
Protective
coatings:
Protective
coatings
for concrete and steel
1
07/02/19
TLM-1,2
CO3 R2
93. Tutorial-6 1 09/02/19
TLM-3
94. Assignment/Qui
z-3
No. of classes required to
complete UNIT-III 15 No. of classes taken:
UNIT-IV : Damage diagnosis and substrate preparation
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
95.
Visual
inspection,
Non-
Destructive
Testing using
Rebound hammer
2
11/02/19
TLM-
1,2
CO4 R3
96.
Ultra-sonic pulse
velocity, semi
destructive
testing, probe test
2
13/02/19
14/02/19
TLM-1
CO4 R3
97.
Pull out test,
chloride
penetration test
1 16/02/19
TLM-1 CO4 R3
98.
Carbonation and
its depth testing,
corrosion activity
measurement
2
18/02/19
20/02/19
TLM-1
CO4 R3
99. Tutorial-7 1 21/02/19 TLM-3
100.
Importance of
substrate/surface
preparation,
surface
preparation methods
1
23/02/19
TLM-1
CO4 R3
101.
Surface
preparation
procedure,
Reinforcing steel
cleaning
1
25/02/19
TLM-1
CO4 R3
102. Tutorial-8 1 27/02/19 TLM-3
103. Assignment/Quiz-
4
No. of classes required to
complete UNIT-IV 11 No. of classes taken:
UNIT-V : Crack repair methods
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
Weekly
104.
Various
methods of
crack repair,
Grouting,
Routing &
Sealing
2
28/02/19
02/03/19
TLM-
1,2
CO5 R4
105. Stitching, Dry
packing,
1
06/03/19
TLM-1
CO5 R2
Autogenous
healing, Overlays
106.
Repair to active
cracks, Repair to
dormant cracks
1
07/03/19
TLM-
1,2
CO5 T1
107.
Corrosion of
embedded steel
in concrete,
mechanism,
stages of
corrosion
damage
2
09/03/19
11/03/19
TLM-
1,2
CO5 T1
108.
Repair of various
corrosion
damaged of
structural elements
1
13/03/19
TLM-1
CO5 R2
109. Tutorial-9 1 14/03/19 TLM-3
110.
Jacketing and its
types (beam,
column, beam
column joint)
2
16/03/19
18/03/19
TLM-
1,2
CO5 T3
111.
Types of
jacketing
(Reinforced
concrete, steel,
FRP)
2
20/03/19
21/03/19
TLM-
1,2
CO5 T3
112.
Strengthening,
beam
shear strengthening
1 23/03/19
TLM-1 CO5 T3
113.
Beam shear and
flexural strengthening
1 25/03/19
TLM-1 CO5 T3
114. Tutorial-10 1
26/03/19 TLM-3
115. Assignment &
Quiz-5
No. of classes required to complete UNIT-V
15 No. of classes taken:
Contents beyond the Syllabus
S.No. Topics to be
covered
No. of
Classes
Required
Tentative
Date of
Completion
Actual
Date of
Completion
Teaching
Learning
Methods
Learning
Outcome
COs
Text
Book
followed
HOD
Sign
116.
117.
Teaching Learning Methods
TLM1 Chalk and Talk TLM4 Demonstration (Lab/Field Visit)
TLM2 PPT TLM5 ICT (NPTEL/Swayam Prabha/MOOCS)
TLM3 Tutorial TLM6 Group Discussion/Project
Part - C
EVALUATION PROCESS:
Evaluation Task COs Marks
Assignment/Quiz – 1 1 A1=5
Assignment/Quiz – 2 2 A2=5
I-Mid Examination 1,2 B1=20
Assignment/Quiz – 3 3 A3=5
Assignment/Quiz – 4 4 A4=5
Assignment/Quiz – 5 5 A5=5
II-Mid Examination 3,4,5 B2=20
Evaluation of Assignment/Quiz Marks: A=(A1+A2+A3+A4+A5)/5 1,2,3,4,5 A=5
Evaluation of Mid Marks: B=75% of Max(B1,B2)+25% of Min(B1,B2) 1,2,3,4,5 B=20
Cumulative Internal Examination : A+B 1,2,3,4,5 A+B=25
Semester End Examinations 1,2,3,4,5 C=75
Total Marks: A+B+C 1,2,3,4,5 100
Course Instructor Module Coordinator HOD
DEPERTMENT OF CIVIL ENGINEERING
NOTIFICATION OF SCHEDULE
GEOTECHNICAL ENGINEERING LAB
Faculty Name: B. NARASIMHA RAO subject code: L149
M. SATYANARAYANA
B.Tech (VI SEM) A.Y 2018-2019
CYCLE-I
DATE B-1 B-2 B-3 B-4 B-5 B-6
19/11/2018 INTRO-1 INTRO-1 INTRO-1 INTRO-1 INTRO-1 INTRO-1
26/11/2018 EXP-I EXP-I EXP-II EXP-II EXP-III EXP-III
03/12/2018 EXP-II EXP-II EXP-III EXP-III EXP-I EXP-I
10/12/2018 EXP-III EXP-III EXP-I EXP-I EXP-II EXP-II
DATE B-7 B-8 B-9 B-10 B-11 B-12
22/11/2018 INTRO-1 INTRO-1 INTRO-1 INTRO-1 INTRO-1 INTRO-1
29/11/2018 EXP-I EXP-I EXP-II EXP-II EXP-III EXP-III
06/12/2018 EXP-II EXP-II EXP-III EXP-III EXP-I EXP-I
13/12/2018 EXP-III EXP-III EXP-I EXP-I EXP-II EXP-II
CYCLE-II
DATE B-1 B-2 B-3 B-4 B-5 B-6
17/12/2018 EXP-IV EXP-IV EXP-V EXP-V EXP-VI EXP-VI
24/12/2018 EXP-V EXP-V EXP-VI EXP-VI EXP-IV EXP-IV
31/12/2018 EXP-VI EXP-VI EXP-IV EXP-IV EXP-V EXP-V
DATE B-7 B-8 B-9 B-10 B-11 B-12
20/12/2018 EXP-IV EXP-IV EXP-V EXP-V EXP-VI EXP-VI
27/12/2018 EXP-V EXP-V EXP-VI EXP-VI EXP-IV EXP-IV
03/01/2019 EXP-VI EXP-VI EXP-IV EXP-IV EXP-V EXP-V
LAB-INCHARGE HOD-CIVIL
CYCLE-III
DATE B-1 B-2 B-3 B-4 B-5 B-6
28/01/2019 INTRO-II INTRO-II INTRO-II INTRO-II INTRO-II INTRO-II
04/02/2019 EXP-VII EXP-VII EXP-VIII EXP-VIII EXP-IX EXP-IX
11/02/2019 EXP-VIII EXP-VIII EXP-IX EXP-IX EXP-VII EXP-VII
18/02/2019 EXP-IX EXP-IX EXP-VII EXP-VII EXP-VIII EXP-VIII
DATE B-7 B-8 B-9 B-10 B-11 B-12
31/01/2019 INTRO-II INTRO-II INTRO-II INTRO-II INTRO-II INTRO-II
07/02/2019 EXP-VII EXP-VII EXP-VIII EXP-VIII EXP-IX EXP-IX
14/02/2019 EXP-VIII EXP-VIII EXP-IX EXP-IX EXP-VII EXP-VII
21/02/2019 EXP-IX EXP-IX EXP-VII EXP-VII EXP-VIII EXP-VIII
CYCLE-IV
DATE B-1 B-2 B-3 B-4 B-5 B-6
25/02/2019 EXP-X EXP-X EXP-XI EXP-XI EXP-XII EXP-XII
04/03/2019 EXP-XI EXP-XI EXP-XII EXP-XII EXP-X EXP-X
11/03/2019 EXP-XII EXP-XII EXP-X EXP-X EXP-XI EXP-XI
18/03/2019 REPETATION REPETATION REPETATION REPETATION REPETATION REPETATION
25/03/2018 INTERNAL INTERNAL INTERNAL INTERNAL INTERNAL INTERNAL
DATE B-7 B-8 B-9 B-10 B-11 B-12
25/02/2019 EXP-X EXP-X EXP-XI EXP-XI EXP-XII EXP-XII
04/03/2019 EXP-XI EXP-XI EXP-XII EXP-XII EXP-X EXP-X
11/03/2019 EXP-XII EXP-XII EXP-X EXP-X EXP-XI EXP-XI
18/03/2019 REPETATION REPETATION REPETATION REPETATION REPETATION REPETATION
25/03/2018 INTERNAL INTERNAL INTERNAL INTERNAL INTERNAL INTERNAL
LAB-INCHARGE HOD-CIVIL
BATECHES ROLL NO:
B-1 15761A0112 TO 16761A0106
B-2 16761A0107 TO 16761A0113
B-3 16761A0114 TO 16761A0119
B-4 16761A0120 TO 16761A0125
B-5 16761A0126 TO 16761A0130
B-6 16761A0131 TO 16761A0135
B-7 16761A0136 TO 16761A0143
B-8 16761A0144 TO 16761A0150
B-9 16761A0151 TO 16761A0156
B-10 16761A0157 TO 17765A0103
B-11 17765A0104 TO 17765A0108
B-12 17765A0109 TO 17765A0113
LAB-INCHARGE HOD-CIVIL
L-145 Environmental Engineering Lab A.Y:2018-19
Faculty Name : Dr. V.Rama Krishna
K. Jaya Rao
B.Tech (VISEM)
Cycle-1
C-1-1. Determination of PH
C-1-2. Determination of TDS
C-1-3. Determination of conductivity
C-1-4. DO Meter
C-1-5 Determination of turbidity.
C-1-6. Determination of settleable solids
Cycle-2
C-2-1.Determination of Acidity and alkalinity
C-2-2. Determination of turbidity (TH, PH, Ca, mg)
C-2-3. Determination of chlorides
C-2-4. Determination of DO
C-2-5. Determination of optimum coagulant (Jar test)
C-2-6 Determination of total solids and suspended solids
Cycle-3
C-3-1. Determination of COD
C-3-2. Determination of fluorides
C-3-3. Determination of sulphates
C-3-4. Determination of BOD
INCHARGE HOD
Faculty Name : Dr. V.Rama Krishna
K. Jaya Rao
B.Tech (VISEM)
Batch-A
A1 15761A0112 to 16761A0106
A2 16761A0107 to 16761A0113
A3 16761A0114 to 16761A0119
A4 16761A0120 to 16761A0125
A5 16761A0126 to 16761A0130
A6 16761A0131 to 16761A0135
Batch-B
B1 16761A0136 to 16761A0143
B2 16761A0144 to 16761A0150
B3 16761A0151 to 16761A0156
B4 16761A0157 to 17765A0103
B5 17765A0104 to 17765A0108
B6 17765A0109 to 16765A0113
INCHARGE HOD
Faculty Name : Dr. V.Rama Krishna
K. Jaya Rao
B.Tech (VISEM)
Batch-A
INCHARGE
HOD
Faculty Name : Dr. V.Rama Krishna
Date/batch A1 A2 A3 A4 A5 A6
22/11/2018 Introduction Introduction Introduction Introduction Introduction Introduction
29/11/2018 C-1-1
C-1-2
C-1-1
C-1-2
C-1-3
C-1-4
C-1-3
C-1-4
C-1-5
C-1-6
C-1-5
C-1-6
22/11/2018 C-1-3 C-1-4
C-1-3 C-1-4
C-1-5 C-1-6
C-1-5 C-1-6
C-1-1 C-1-2
C-1-1 C-1-2
06/12/2018 C-1-5
C-1-6
C-1-5
C-1-6
C-1-1
C-1-2
C-1-1
C-1-2
C-1-3
C-1-4
C-1-3
C-1-4
13/12/2018 C-2-1 C-2-2 C-2-3 C-2-4 C-2-5 C-2-6
20/12/2018 C-2-2 C-2-3 C-2-4 C-2-5 C-2-6 C-2-1
27/12/2018 C-2-3 C-2-4 C-2-5 C-2-6 C-2-1 C-2-2
03/01/2019 C-2-4 C-2-5 C-2-6 C-2-1 C-2-2 C-2-3
31/01/2019 C-2-5 C-2-6 C-2-1 C-2-2 C-2-3 C-2-4
01/02/2019 C-2-6 C-2-1 C-2-2 C-2-3 C-2-4 C-2-5
14/02/2019 C-3-2
C-3-3 C-3-1 C-3-4
C-3-2
C-3-3 C-3-1 C-3-4
21/02/2019 C-3-4
C-3-2
C-3-3 C-3-1 C-3-4
C-3-2
C-3-3 C-3-1
28/02/2019 C-3-1 C-3-4
C-3-2
C-3-3 C-3-1 C-3-4
C-3-2
C-3-3
07/03/2019 Additional Experiments
14/03/2019 repetition repetition repetition repetition repetition repetition
28/03/2019 Internal Internal Internal Internal Internal Internal
K. Jaya Rao
B.Tech (VISEM)
Batch-B
Date/batch B1 B2 B3 B4 B5 B6
19/11/2018 Introduction Introduction Introduction Introduction Introduction Introduction
26/11/2018 C-1-1
C-1-2
C-1-1
C-1-2
C-1-3
C-1-4
C-1-3
C-1-4
C-1-5
C-1-6
C-1-5
C-1-6
03/12/2018 C-1-3
C-1-4
C-1-3
C-1-4
C-1-5
C-1-6
C-1-5
C-1-6
C-1-1
C-1-2
C-1-1
C-1-2
10/12/2018 C-1-5
C-1-6
C-1-5
C-1-6
C-1-1
C-1-2
C-1-1
C-1-2
C-1-3
C-1-4
C-1-3
C-1-4
17/12/2018 C-2-1 C-2-2 C-2-3 C-2-4 C-2-5 C-2-6
24/12/2018 C-2-2 C-2-3 C-2-4 C-2-5 C-2-6 C-2-1
31/12/2018 C-2-3 C-2-4 C-2-5 C-2-6 C-2-1 C-2-2
28/01/2019 C-2-4 C-2-5 C-2-6 C-2-1 C-2-2 C-2-3
04/02/2019 C-2-5 C-2-6 C-2-1 C-2-2 C-2-3 C-2-4
11/02/2019 C-2-6 C-2-1 C-2-2 C-2-3 C-2-4 C-2-5
18/02/2019 C-3-2
C-3-3 C-3-1 C-3-4
C-3-2
C-3-3 C-3-1 C-3-4
25/02/2019 C-3-4
C-3-2
C-3-3 C-3-1 C-3-4
C-3-2
C-3-3 C-3-1
04/03/2019 C-3-1 C-3-4
C-3-2
C-3-3 C-3-1 C-3-4
C-3-2
C-3-3
11/03/2019 repetition repetition repetition repetition repetition repetition
18/03/2019 Additional Experiments
28/03/2019 Internal Internal Internal Internal Internal Internal
INCHARGE HOD