2010 CA08103002Z-EN www.eaton.com Single phase Two phase Three phase Single phase Two phase Three phase Single phase Three phase Single phase Two phase Three phase Single phase Two phase Three phase 1/10 3.0 1.5 1.0 1/8 3.8 1.9 1.2 1/6 4.4 2.2 1.4 1/4 5.8 2.9 1.8 1/3 7.2 3.6 2.3 1/2 9.8 4.0 4.4 4.9 2.0 2.2 3.2 1.3 2.5 1.0 1.1 2.0 0.8 0.9 3/4 13.8 4.8 6.4 6.9 2.4 3.2 4.5 1.8 3.5 1.2 1.6 2.8 1.0 1.3 1 16.0 6.4 8.4 8.0 3.2 4.2 5.1 2.3 4.0 1.6 2.1 3.2 1.3 1.7 1-1/2 20.0 9.0 12.0 10.0 4.5 6.0 6.4 3.3 5.0 2.3 3.0 4.0 1.8 2.4 2 24.0 11.8 13.6 12.0 5.9 6.8 7.7 4.3 6.0 3.0 3.4 4.8 2.4 2.7 3 34.0 16.6 19.2 17.0 8.3 9.6 10.9 6.1 8.5 4.2 4.8 6.8 3.3 3.9 5 56.0 26.4 30.4 28.0 13.2 15.2 17.9 9.7 14.0 6.6 7.6 11.2 5.3 6.1 7-1/2 80.0 38.0 44.0 40.0 19.0 22.0 27.0 14.0 21.0 9.0 11.0 16.0 8.0 9.0 10 100 48.0 56.0 50.0 24.0 28.0 33.0 18.0 26.0 12.0 14.0 20.0 10.0 11.0 15 135 72.0 84.0 68.0 36.0 42.0 44.0 27.0 34.0 18.0 21.0 27.0 14.0 17.0 20 94.0 108 88.0 47.0 54.0 56.0 34.0 44.0 23.0 27.0 35.0 19.0 22.0 25 118 136 110 59.0 68.0 70.0 44.0 55.0 29.0 34.0 44.0 24.0 27.0 30 138 160 136 69.0 80.0 87.0 51.0 68.0 35.0 40.0 54.0 28.0 32.0 40 180 208 176 90.0 104 112 66.0 88.0 45.0 52.0 70.0 36.0 41.0 50 226 260 216 113 130 139 83.0 108 56.0 65.0 86.0 45.0 52.0 60 133 154 103 67.0 77.0 53.0 62.0 75 166 192 128 83.0 96.0 66.0 77.0 100 218 248 165 109 124 87.0 99.0 125 312 208 135 156 108 125 150 360 240 156 180 125 144 200 480 320 208 240 167 192 250 602 403 302 242 300 482 361 289 350 560 414 336 400 636 477 382 500 786 590 472 a) To obtain full-load currents for 200 and 208 V motors, increase corresponding 220 - 240 V ratings by 15 and 10 percent, respectively. b) To obtain full-load currents for 265 and 277 V motors, decrease corresponding 220 - 240 V ratings by 13 and 17 percent, respectively. Quote from Power Conversion Equipment - UL 508C, May 3, 2002. Reproduced from UL 508 C, Power Conversion Equipment, 3rd edition (May 2, 2002) with permission of Underwriters Laboratories Inc.
