Control Grips

KSeries SSeries CSeries JSeries LSeries

This compact joystick "Knob"is available with a grey or black finish, with none, 1 or 2 momentary switches. When installed on our joysticks the knob is suitablefor wet or exposed applications requiring an IP-66 rating.

Our smallest and lowest costgrip comes standard with a trigger and 2 long life switches.Available in grey or black, it includes 24" of wire and spade connectors on the switches for easy servicing. Supplied alone or installed on an electronic joystick.

This is our mid size grip available with up to 5 switchesor proportional functions,trigger, toggle switches, LED's and other options. Supplied alone or installed on an electronic joystick.

www.suregripcontrols.com

Specifically designed for our joysticks, it is available with up to 5 switched or proportional functions, trigger, LED's, toggle switches and other options. If sold separately it is supplied with a threaded 12 or 14mmstud.

Our most popular grip, it can be supplied with up to 10 switched or proportional functions, triggers, LED's, toggle switches or 10 button keypad. It is also available our unique double trigger. Supplied alone or installed on an electronic joystick.

Knob S Handles C Handles J Handles L Handles

CONTROLS INC.TM

"Tough controls for tough jobs"

Control Grip Options

Customer Order Options

Series Trigger Faceplate Switches Wires AccessoriesKB = Knob (black)KG = Knob (grey)SB = S Series (black)SG = S Series (grey)CB = C Series (black)CG = C Series (grey)JB = J Series (black)JG = J Series (grey)LB = L Series (black)LG = L Series (grey)

#4-1413 McGill Road Kamloops B.C. Canada V2C 6K7

Ph: (250) 374-2278 Fax: (250) 374-1099 Toll Free: 1-800-831-2278

www.suregripcontrols.com

0 = No trigger1 = Single trigger2 = Double triggerV = Voltage module

( All other options please call factory )

M0 = Blank faceplateM1 = 1 momentary switchM2 = 2 momentary switchesM4 = 4 momentary switchesM6 = 6 momentary switchesM8 = 8 momentary switches

2 = 2' of wire10 = 10' of wire

None (leave blank)DP = Diode packKP10L = Left hand keypadKP10R = Right hand keypadA0 = Adapter Bushing 1/4" holeA1 =Adapter Bushing 10mm x 1.5A2 =Adapter Bushing 12mm x 1.25A3 =Adapter Bushing 12mm x 1.75A4 =Adapter Bushing 14mm x 2A5 =Adapter Bushing 5/8" NC

CONTROLS INC.TM

LED-24GMaintained Push Button PB-2MA

Toggle SwitchTO-3MA

Toggle SwitchTO-3MOL

Proportional PC-V2 Module

Standard SwitchesSW-00

ProportionalButtons

ProportionalSlider Module

ProportionalMicro Joystick

KSeries Knob(0-2 Button) SSeries Handle

(0-2 Button) CSeries Handle(0-4 Button) J Series Handle

(0-4 Button) L Series Handle(0-8 Button)

L Single TriggerL-TR-01

L DoubleTriggerL-TR-02

10 Button Keypad("L" Series Only)

KP-10L1KP-10R1

Threaded Adapters

Inline Diode Protection Pack

Set Screws Adapters

Handle Studs Clamping Adapters

CONTROLS INC.TM

Industrial Joysticks

JMSeries JLSeries

Adjustable+/-20o

JM Series Hall Effect joystick has a compact body but uses all the same internal components of the larger JL Series. With the simplicity of only 3 moving parts, a strong metal housing and Teflon impregnated wear materials; these joysticks are designed for the really tough applications. They are both configurable for single or dual axis, springreturn to center, maintained friction positioning, switched outputs, proportional 5 VDC outputs or with an internal high current PWM driver card. When supplied with the K Series knob they are also suitable for wet or exposed applications.

The JL Series is a simple, reliable and "Operator Friendly" input device that will change the way you look at electronic joysticks. Our unique spherical metal housing creates a solid base that protects the electronics from outside interference and provides the foundation for a revolutionary new concept, an operator adjustable mounting system.

The spherical body of the joystick is mounted within a two piece clamp that permits up to 20 degrees of adjustment in any direction. This feature allows an operator to quickly and easily adjust the mounting angle of the joystick to optimize ergonomics and reduce fatigue.

www.suregripcontrols.com

JM Joysticks JL Joysticks

CONTROLS INC.TM

"Tough controls for tough jobs"

+/- 20o+/- 20o

360o 360o

Joystick Options

Sure Grip Joystick Technical Info

JM / JL Series Features JL Series Special Features

Switched Output Joystick+ Momentary Switched: 24 VDC: 5 amps, (3 amps inductive) 120 VAC: 5 amps (3 amps @ 250 VAC)+ Movement to Activate: 16 degrees, on axis (+/- 4 degrees) 22 degrees, at 45 degrees (+/- 4 degrees)

Mechanical:+ Maximum handle travel: 20 +/- 1 degrees (on axis) 28 +/- 1 degrees (at 45 degrees)+ Force measured at bottom of faceplate (typical) to come out of center: 600 grams (on axis) 750 grams (at 45 degrees)+ Force measured at bottom of faceplate (typical) at end of stroke: 750 grams (on axis) 900 grams (at 45 degrees)+ Environmental Rating: Joystick c/w Knob: IP-66 Joystick c/w J Series Basic Grip: IP-64 Joystick c/w any handle with trigger: IP-55

Proportional Voltage Output: (typical)Supply voltage: 5.0 VDC (+/- 0.1 VDC)Supply current: 30 mA maximumTypical Output: 0.5 - 2.5 - 4.5VDC, (+/- 0.1 VDC)

Performance Specifications: (actual)+ Output at maximum negative X or Y displacement: 10% +/- 2% of supply voltage+ Actual Output at null (handle center): 50% +/- 2% of supply voltage+ Output at maximum positive X or Y displacement: 90% +/- 2% of supply voltage+ Maximum output current: 2mA

+ Non-contact, programmable Hall sensors+ Long life - lab tested to 20 million cycles+ Rugged design - die-cast metal housing+ Infinite resolution+ Single and dual axis models+ Switched or proportional outputs+ Simple construction: only 3 moving parts+ Self lubricated teflon blended wear parts+ EMI/RFI protected+ Stable null+ Factory calibrated output range+ Low power consumption+ Spring return to center or friction maintained positioning

+ Gimbal mounting +/- 20 degrees+ 360 dregree rotation+ Internal or external wire routing+ Gated or maintained positioning

CONTROLS INC.TM

#4-1413 McGill Road Kamloops B.C.Canada V2C 6K7

Ph: (250) 374-2278 Fax: (250) 374-1099 Toll Free: 1-800-831-2278

www.suregripcontrols.com

KKnob with 0-2 Button Faceplate

JMseries

JLseries

SHandle with 0-2 Button Faceplate CHandle with

0-4 Button Faceplate J Handle with

0-4 Button Faceplate LHandle with

0-8 Buttons 10 Function Keypad

CONTROLS INC.TM

52mm

96mm

231mm212mm

50mm

70mm63mm

57mm

57m

m

5.50mm72mm cut out

63mm cut out

72mm

72mm

5mm

The Single Axis Driver Board (Part#: SDB-P1) has been designed to control two proportional solenoids for applications like thumbs, grapple rotate, tilts etc. It is equipped with two current compensated PWM outputs and one digital “off neutral” output. Each output will drive up to 2.5 amps and is protected against accidental short circuit, overload and inductive kick back. The SDB-P1 also includes a 50 ma 5 volt supply to power a joystick or other input signal device. The inputs are configured for either a single 0.5-2.5-4.5 vdc signal or dual 1-4 vdc analog inputs.

Wiring the SDB-P1 is easy with removable screw terminal strips that accept 18-24 gauge wire. The output settings are easily modified by adjusting the onboard pots for minimum and maximum flow for each output. There is also a green LED for “RUN” mode and a red LED for “CALIBRATE” mode.

The SDB-P1 board can also be equipped with a “program select option” that will allow the user to select between three preprogrammed output settings when changing between attachments like a thumb, hammer or compactor.

Joystick Driver Board (Part#: JDB-P2) is designed to work with our JM and JL Hall effect joysticks when a direct joystick to solenoid valve solution is desired.

The board fits inside the lower joystick housing and is easily programmed by plugging in a serial cable and using the standard Windows “Terminal” program. The minimum flow, maximum flow and ramp rate can all be adjusted for each proportional output.

The DB-L17 Logic Driver Board can read up to 10 inputs and can control up to 17 high current outputs to allow complex control of a machine's functions from a simple, easy to use control handle. The DB-L17 is factory programmed to the customer's specifications and is designed for easy installation and reliable operation in mobile equipment. The DB-L17 can be used to replace relays, timers, diode logic circuits and programmable logic controllers (PLCs) in many applications.

www.suregripcontrols.com

The DFA-01/02 provides direct from handle tovalve, proportional control for the operation of industry-standard ratio metric proportional valves. You can now use Sure Grip Controls' non-contact proportional modules or ourjoysticks to directly control proportional valves such as the Sauer Danfoss™ PVG 120 and PVG 32 series proportional valves.

The DFA-01/02 is installed in-line a Sure Grip control or joystick wiring harness. The operator will have bi-directional proportional control of Danfoss™ proportional valves using a proportional rocker, two proportional flex pushbuttons or our joysticks. (the DFA-01 version mates with our PC-V2 modules, the DFA-02 version mates with our joysticks.)

The DFA-01/02 provides the drive signal required by the valve, as well as a high-power valve enable signal whenever the drive signal is “off neutral”.

Single Axis Driver Board

The JDB-P2 boards are equipped with two current compensated PWM proportional outputs and one “off neutral” digital output for each axis. Each output is rated for 2.5 amps and is protected against accidental short circuit, over load and inductive kick back. It also includes a 50 ma 5 volt supply to power our JL or JM Hall effect joystick.

DB-L17 Logic Driver Board

Joystick Driver Board

TM

Danfoss Adapter Board

Electronic SpecificationsCONTROLS INC.TM

#4-1413 McGill Road Kamloops B.C. Canada V2C 6K7

Ph: (250) 374-2278 Fax: (250) 374-1099 Toll Free: 1-800-831-2278

www.suregripcontrols.com

CONTROLS INC.TM

Single Axis Driver Board (Part# SDB-P1)

Joystick Driver Board (Part# JDB-P2)

DBL-17 Logic Driver Board (Part# DBL-17)

Danfoss Adapter Board (Part# DFA-01)

Specifications

Features

Parameter Min. Typ. Max. UnitPower Supply:

Supply voltage12/24 VDC in 12/24 VDC out

Ground

The Single axis driver board is a current compensated output device that is designed to proportionally drive 2 solenoids ( 1 per function) from a proportional input signal. The board has been designed to accommodate ease of installationand configuration. Power and output termination is provided through 5 potentiometers whose function is to set the mode, min, and max operating parameters for each output.

FeaturesThe Joystick Driver Board is a current compensated output device that is designed to proportionally drive 4 solenoids (2 per axis) from a proportional joystick signal.The board has been designed to accommodate ease of installation and configuration which is provided through the use of a connected computer with no special software required.

Aux outPWM 1 outPWM 2 out

Ground out+5VSignal in 1

#1 GND#2 X out A#3 X out B#4 Y out A#5 Y out B

12/24 VDC

#9 X-AUX1 output#10 Y-AUX2 output

17 outputs

10 inputs

12/24 VDC

+5 VDC

Ground

Signal in 2

Supply current (idle)Supply current (max)Aux. VoutAux. Current (+5V)

Analog Inputs:Input rangeNeutral point (single)Neutral point (dual)

PWM Outputs:FrequencyMin. duty cycleMax. duty cycleOutput current

Current compensation:Correction rangeMax. coil size

6---20

0.5--

----

-40-

-2.50.5

-2055-

200599-

-3000

4.5--

28---30

---2.5

+40-

VDCVDCVDC

VDCmAAVDCmA

Hz%%A

%mA

Specifications Parameter Min. Typ. Max. UnitPower Supply:

Supply voltageSupply current (idle)Supply current (max)Aux. VoutAux. Current (+5V)

Analog Inputs:Input rangeNeutral point

6---20

0.5-

PWM Outputs:FrequencyMin. duty cycleMax. duty cycleOutput current

----

Current compensation:Correction rangeMax. coil size

-40-

-2.5

-20125-

200599-

-3000

4.5-

28---30

---3

+40-

VDCVDC

VDCmAAVDCmA

Hz%%A

%mA

Specifications Parameter Min. Typ. Max. UnitPower Supply:

Supply voltageSupply current (idle)Supply current (max)Aux. Vout

Inputs:Input range

6---

0Outputs:

Output current -

-

-15245

-

supply

28---

2.5

VDC

VDCmAAVDC

A

Specifications+ Operating voltage: 6-28 VDC + Wire terminals: solder post + Ramp rate (factory): 300 ms + Enable output: 3 amps max. + Signal output (neutral) 50% machine voltage +/- 2% (max) 80% machine voltage +/- 5% (min) 20% machine voltage +/- 5% + Case size: 4” x 1” x 1” + Operating temperature: -40 to 70 Celsius