Embed Size (px)
Citation preview
Audio Kit for
Qz, Q1 and Q36 7
8 9
10 11
12 13
2 3
5
1 4
1 Noise canceling microphone
2 Hybrid mic 3 Release Tab4 Speakers
5 Speaker Jack6 Corded Microphone (*Only with Q1/Q3)
7 Replacement mic sponges 8 Allen wrench
9 Alcohol pads10 Speaker Booster
pads11 Velcro pads12 Glue plates13 Hybrid mic clip
CONTENTS OPTION B: USING THE GLUE PLATE
1 Remove the Back Plate by taking out both screws 2 Use the Alcohol pad to clean the exact spot on the helmet3 Peel off protective backing sheet4 Press here for 15 seconds5 Allow the glue to dry for 24 hours6 Fasten both screws tightly
Glue the Audio Kit onto your helmet when the standard Back Plate method cannot be used. Choose which of the2 glue plates is most suitable for your helmet.While we have no reason to believe that the gluing option might negatively affect any helmet, Cardo does not assume any responsibility, irrespective of its nature and circumstances. The Glue Plate is offered as an option that you may use at your own risk and subject to renouncement of any future claims.
POSITIONING THE HYBRID MICROPHONE
1 Open the lining between the helmet’s inner padding. Use the Velcro pad to hold the Hybrid Microphone in place. Attach the Microphone to the Velcro pad.
2 Adjust the location so that the microphone is located opposite the center of your mouth.
PLACING THE SPEAKERS
For best clarity, place speakers directly opposite and close to the ears. Helmets with deep recesses may require padding to bring the speakers closer for ideal positioning. Optional speaker booster pads are provided for this purpose. To use, place the speaker booster pad between the Velcro pad in the helmet cavity and the speaker.1 Attach Velcro pads to inside of Helmet.2 Cross the long speaker wire over the center of
the helmet to enhance FM radio reception.
Using two speakers inside the helmet may be prohibited in certain jurisdictions. If this is the case, position both speakers on one side of the helmet.
CHANGING THE MICROPHONE TYPE
Removing: Before changing the microphone, completely remove the Audio Kit and backplate from the helmet.
Attaching: Replace the screws to reattach the backplate to the Audio Kit before reassembling on the helmet and fully tightening the screws.
POSITIONING THE CORDED MICROPHONE
Attach Velcro to inside front of helmetThe Corded Microphone can be used with Full face helmets only (not Modular helmets).Some helmets with air vents may require the mic to be repositioned if mic audio is affected.
REPLACING THE CORDED MICROPHONE SPONGE
A replacement corded microphone sponge is provided for future use should you need it. NOTE: The wires to the microphone are delicate. Avoid touching them.
1 Pinch and pull existing microphone sponge2 Carefully remove the existing sponge. 3 Remove protective backing sheet from replacement sponge4 Carefully attach the new sponge to the microphone
Installation Guide
OPTION A : USING THE BACK PLATE
1 Loosen both screws2 Push the back plate between
the helmet’s outer shell and inner padding
3 Tighten the screws
THIS CAN ONLY
BE DONE ONCE!
English - Chinese
ATTACH THE SCALA RIDER AUDIO KIT TO YOUR HELMET
Attach the scala rider Audio Kit to your helmet with the standard Backplate using the following instructions
ma
n00124 r
www.cardosystems.com
USa & Canada: 1-800-488-0363 International: +49 89 450 36819
6 7
8 9
10 11
12 13
2 3
5
1 4
1
2
3
4
5
7
8
9
10
11
12
13
1
2
3
4
5
6
1 2
1 2
1 3 4
1
2
3
ma
n00124 r
www.cardosystems.com
USa & Canada: 1-800-488-0363 International: +49 89 450 36819
