Construction Plant MaintenanceQuality Network Event

23rd August 2013

Construction Plant MaintenanceQuality Network Event

23rd August 2013

SQA Qualifications: Plant MaintenanceSQA Qualifications: Plant Maintenance

Level 1 SVQ in Plant Maintenance: G7C9-21

Level 2 SVQ in Plant Maintenance: G7CA-22

Level 3 SVQ in Plant Maintenance: G7CC-23

The above qualifications have now lapsed as from 30th June 2013 and have been replaced with a new qualification at Level 2 and Level 3 (Level 1 has been withdrawn). Any candidates currently registered will need to complete by June 2015

T

Lapsed SVQ Qualifications Lapsed SVQ Qualifications

SVQ Level 1 in Plant Maintenance

 

 

MANDATORY UNITS

 

PM 01 Contribute to a Safe Working Environment

PM 02 Carry Out Basic Maintenance on Plant and Equipment

PM 03 Carry Out Bench Fitting Activities

PM 04 Operate Plant Machinery and Equipment (No Load Conditions)

Lapsed SVQ QualificationsLapsed SVQ Qualifications

SQA Level 2 in Plant Maintenance

MANDATORY UNITS

 

PM 05 Carry Out Servicing and Maintenance of Plant and Equipment

PM 06 Remove and Replace Plant Equipment Components

PM 07 Dismantle and Assemble Plant and Equipment Components

PM 08 Maintain the Work Area

PM 09 Inspect Plant and Equipment for Operational Serviceability

PM 10 Diagnose Faults in Plant Equipment Systems and Components 

Lapsed SVQ Qualifications Lapsed SVQ Qualifications

PLUS OPTIONAL UNITS (3 units required from the following 7 units)

PM 11 Repair Plant and Equipment by Soldering and Welding

PM 12 Produce One-off Components to Assist Plant and

Equipment Activities

PM 13 Move Standard Loads

PM 14 Install Plant and Equipment for Operational Activities

PM 15 Carry Out Specific Tests on Plant Equipment

PM 16 Configure Plant and Equipment for Operational Activities

PM 23 Hand Over Plant and Equipment to the Control of Others

Lapsed SVQ QualificationsLapsed SVQ Qualifications

SQA Level 3 in Plant Maintenance

MANDATORY UNITS

 

PM 17 Service and Maintain the Condition of Plant and Equipment

PM 18 Return Plant and Equipment to Service by Repair and Overhaul

PM 19 Conduct Testing of Plant and Equipment Following Repair

PM 20 Diagnose and Determine the Cause of Faults and Problems in Plant

and Equipment

PM 21 Control the Use of Allocated Resources for Plant Maintenance and

Repair Activities

 

 

Lapsed SVQ QualificationsLapsed SVQ Qualifications

PLUS OPTIONAL UNITS (3 units required from the following 9 units)

 

PM 11 Repair Plant and Equipment by Soldering and Welding

PM 12 Produce One-off Components to Assist Plant and Equipment

Activities

PM 13 Move Standard Loads

PM 14 Install Plant and Equipment for Operational Activities

PM 16 Configure Plant and Equipment for Operational Activities

PM 22 Inspect Plant and Equipment for Serviceability

PM 23 Hand Over Plant and Equipment to the Control of Others

PM 24 Provide Technical Information and Advice to Users of Plant and

Equipment

PM 25 Co-ordinate Plant Maintenance Work Activities

New QualificationsNew Qualifications

Current from June 2013 New titles: SVQ 2 in Construction Plant or Machinery

Maintenance SVQ 3 in Construction Plant or Machinery

Maintenance Level 2 and 3 only No Level 1

New QualificationsNew Qualifications

SVQ 2 in Construction Plant or Machinery Maintenance Mandatory Units

VR641 Conform to general workplace health, safety and welfare

VR642 Conform to productive work practices

VR643 Move, handle or store resources

VR659 Operate plant or machinery for non-operational activities

VR660 Service plant or machinery

VR661 Remove and replace plant or machinery components to restore operational

use

VR662 Dismantle and assemble plant or machinery components to replace worn,

damaged or faulty parts

VR663 Inspect plant or machinery for operational serviceability

VR664 Diagnose faults in plant or machinery systems or components

New QualificationsNew Qualifications

Plus Optional Units (two units from the following required)

VR665 Install, repair or modify construction resources by heating, welding,

brazing, soldering and thermal cutting

VR666 Produce one-off components to restore or maintain the operational

functions of plant or machinery

VR667 Install plant or machinery for operational activities

VR668 Carry out specific tests on plant or machinery to determine operational

serviceability

VR669 Configure plant or machinery for specific operational activities

VR672 Hand over plant or machinery to the control of others

Total of 11 units required

New QualificationsNew Qualifications

SVQ 3 in Construction Plant or Machinery Maintenance

Mandatory Units

VR209 Confirm work activities and resources for the work

VR210 Develop and maintain good working relationships

VR211 Confirm the occupational method of work

VR659 Operate plant or machinery for non-operational activities

VR664 Diagnose faults in plant or machinery systems or components

VR670 Determine and complete service to maintain plant or machinery

VR671 Determine and advise on the viability of repair or replacement for returning

plant or machinery to service

New QualificationsNew Qualifications

Plus Optional Units (one unit from the following required)

VR672 Hand over plant or machinery to the control of others

VR673 Provide technical information, advice and guidance to users of plant or

machinery

Plus Optional Units (two units from the following required)

VR665 Install repair or modify construction resources by heating, welding,

brazing, soldering and thermal cutting

VR666 Produce one-off components to restore or maintain the operational

functions of plant or machinery

VR667 Install plant or machinery for operational activities

VR669 Configure plant or machinery for specific operational activities

Total of 10 units required

Subject Specialist E.Vs.

No reportable External Verification issues found

Developmental and supportive approach to verification.

Identifying and sharing good practice.

Quality Networks.

Partnership

“ Critical Friend”

SQA Approach SQA Approach