CONSTRUCTION EQUIPMENT - mbw.com · MORTAR MIXERS 32-33 ... Patented polyethylene slide bearings provide minimal ... (1.37 mm) .067 in (1.72 mm) Centrifugal Force: 1920 lbs (8.5 kN)

WWW.MBW.COM 1

COMPACTION & CONCRETE CONSTRUCTION EQUIPMENT

WWW.MBW.COM

Since 1967, MBW has been manufacturing one of the construction industry’s most interesting lines of compaction, concrete and related equipment.

W H A T M A K E S T H E M B W L I N E I N T E R E S T I N G ?

MBW is not a copyist – we do not duplicate designs developed by others. MBW begins each new engineering project with the assumption that significant progress can be made in terms of improved productivity, reduced maintenance, longer life, enhanced user safety or lower long-term cost of ownership. Often, MBW’s R&D efforts result in entirely fresh approaches to solving industry problems. Many of our products have pushed the productivity envelope to new heights. Most MBW products solve long standing maintenance issues and extend product life expectations. Our goal is to provide equipment users with products of significant, tangible, comparative value... reasons to invest in MBW products.

DIRE

CTOR

YR A M M E R S 3 - 5 R422/R442 3

R482 4

Airammer 5

S I N G L E D I R E C T I O N V I B R A T O R Y P L A T E S 5 - 1 1 1000 Series 6-7

2000 Series 8-9

3000 Series 10

5000 Series 11

7000 Series 11

R E V E R S I B L E V I B R A T O R Y P L A T E S 1 2 - 1 5 Mechanical Reversible Plates 12-13

Hydraulic Reversible Plates 14-15

R O L L E R S 1 6 - 2 1 Skid Steer Vibratory Roller Attachments 18

Stick-Mounted Static & Vibratory Roller Attachments 19-21

B A R R E L M O U N T E D S P R A Y E R S 2 3

T R O W E L S 2 4 - 2 7 Walk-Behind Power Trowels 24-25

Ride-On Power Trowels 26-27

S C R E E D S 2 8 - 3 1 Blitzscreed® Vibratory Truss Screed 28

Power Winches 29

ScreeDemon™ Vibratory Wet Screed 30-31

M O R T A R M I X E R S 3 2 - 3 3

S L I P F O R M P A V E R S 3 4 - 3 5

C O N T A C T I N F O R M A T I O N B A C K

M B W C O N S T R U C T I O N D I V I S I O N

WWW.MBW.COM 3

* Clean sand, optimum moisture. MBW recommends that lifts not exceed 12” of granular soil, 9” of cohesive soil.Fuel capacity of 1.1 gal (4.2 L); Engine 3600 rpm( ) Metric Measurements

The R422 & R442 RAMMERS are ideally suited for the compaction of granular, mixed and cohesive soils in confined areas. The R422 & R442 offer highly productive percussion rammers at 145 or 154 lbs. The contoured fuel tank provides the largest fuel capacity in its class and effectively baffles engine noise. Power is supplied by Honda engines. Model R442 delivers approximately 25% more compaction force and is recommended for heavy clay soils.

Models R422 & R442 with the Honda GXR120 are recommended for altitude above 4000 ft.

Elevated bellows placement for trench applications

Patented polyethylene slide bearings provide minimal internal wear

11” ductile cast iron tamping shoe

4” and 6” trench shoes available for the 422

Available with a choice of two engines Honda GX100 Honda GX100 with

oversized air filter Honda GXR120

US & International Patents

RAMM

ERS

OPTIONAL SHOEAIR FILTER OPTION

MODEL R422 R442

Shoe Size 11 x 13 in(28 x 33 cm)

Engine Options & Operating Weight

Honda GX100 145 lb (66 kg)Honda GX100

with Oversized Air Filter 149 lb (68 kg)Honda GXR120 145 lb (66 kg)


with Oversized Air Filter 154 lb (70 kg)Honda GXR120 150 lb (68 kg)

Percussion Rate Up to 720 blows/min

Compaction Area 2520 ft2/hr (234 m2/hr) 2900 ft2/hr (269 m2/hr)

Travel Speed Up to 55 ft/min (16 m/min)

Compaction Depth* Up to 18 in (45 cm)

R 4 2 2 / R 4 4 2COMPACTION

V I B R A T O R Y R A M M E R SS I N G L E D I R E C T I O N V I B R A T O R Y P L A T E S

R E V E R S I B L E V I B R A T O R Y P L A T E S

S K I D S T E E R R O L L E R A T T A C H M E N T SS T I C K M O U N T E D S T A T I C &

V I B R A T O R Y R O L L E R A T T A C H M E N T S

2 WWW.MBW.COM

WWW.MBW.COM 54 WWW.MBW.COM

* Clean sand, optimum moisture. MBW recommends that lifts not exceed 12” of granular soil, 9” of cohesive soil.Fuel capacity of 1.1 gal (4.2 L); Engine 3600 rpm( ) Metric Measurements

* Clean sand, optimum moisture. MBW recommends that lifts not exceed 12” of granular soil, 9” of cohesive soil.( ) Metric Measurements

RAM

MER

S RAMM

ERSThe R482 RAMMERS are equipped

with integral tachometers and hour meters that indicate

when maximum operational performance is being reached

and when maintenance intervals are needed. The result is higher productivity

and increased service life. Weighs between 158-165 lbs. Model R482 with the Honda GXR120 is recommended for

altitude above 4000 ft.

Available with a choice of two engines which provide sure starts and long-

term low maintenance. Honda GX100 Honda GXR120


MODEL R482 - 11” SHOE R482 - 13” SHOEShoe Size 11 x 13 in (28 x 33 cm) 13 x 15 in (33 x 38 cm)

Engine Options

Honda GX100 158 lb (72 kg)Honda GXR120 158 lb (72 kg)

Honda GX100 165 lb (75 kg)Honda GXR120 165 lb (75 kg)

Percussion Rate Up to 650 blows/min

Compaction Area 3300 ft2/hr (307 m2/hr) 3900 ft2/hr(362 m2/hr)

Travel Speed Up to 60 ft/min (18.3 m/min)


R 4 8 2 A R 5 6 / 5 7 A I R A M M E R

TACHOMETER 4” & 6” NARROW SHOE WITH 12” EXTENSION

The Airammer© is a pneumatically powered rammer. It eliminates a long list of engine related problems. There are no fuel or fuel mixing issues, no carburetor, no spark plug, no rewind starter, no flooding problems, no air or fuel filters that can be plugged, no rpm issues, all of which affect performance.

The Airammer also offers the following advantages:

No need to handle flammable gas or oil

Lower maintenance cost $$

Motor is closer to the gearbox for better balance

No exhaust fumes, safe for indoor use

Easier to run and maneuver

Can be transported or stored in any position

No frustration of trying to start an engine

No stopping to refuel

Less time spent on pre-run check over, i.e. check oil, clean air filter, fuel up, etc.

Less down time for routine maintenance

MODEL AR56 AR57Shoe Size Iron 11 x 13 in (28 x 33 cm) Alum 13 x 15 in (33 x 38 cm)

Operating Weight 124 lb (56 kg) 126 lb (57 kg)

Percussion Rate 650 blows/min 650 blows/min

Compaction Area 3300 ft2/hr (307 m2/hr) 3900 ft2/hr(362 m2/hr)

Travel Speed Up to 60 ft/min (18.3 m/min) Up to 60 ft/min (18.3 m/min)

Compaction Depth* Up to 24 in (61 cm) Up to 24 in (61 cm)

Air Required 75 cfm 100 psi 75 cfm 100 psi

RPM 4500 4500


* Clean sand, optimum moisture. MBW recommends that lifts not exceed 12”.( ) Metric Measurements

SING

LE D

IREC

TION

VIBR

ATOR

Y PLA

TES SINGLE DIRECTION VIBRATORY PLATES


produced by the machine’s exciter. With amplitudes up to .067 inches, centrifugal force up to 2780 lbf and travel speeds to 83 feet per minute these plates are ideal in confined areas of granular soils including sands, bank run gravel and capable of achieving lift depths of up to 10 inches or 12 inches for the GP18.

These lightweight plates weighing 133 lbs (60 kg) to 165 lbs (75 kg) are easy to lift and maneuver about the job site. Accompanied by intense vibration, this series of plates are ideally suited as an economical alternative for small to medium compaction applications.

Standard with Honda engine and lift cage

One piece exciter with self cleaning open base plate design

Optional UHMW paving pad for placing interlocking paving stone/brick/block

Optional wheel kit

Patented

MODEL GP12 GP15 GP18

Plate Size WxL 13 x 22.5 in(33 x 57 cm)

16 x 22.5 in(40 x 57 cm)

18 x 22.5 in(46 x 57 cm)

Operating Weight 130 lb (59 kg) 139 lb (63 kg) 161 lb (73 kg)

Engine Honda GX120

Amplitude .058 in (1.47 mm) .054 in (1.37 mm) .067 in (1.72 mm)

Centrifugal Force 1920 lbs (8.5 kN) 2000 lbs (8.9 kN) 2780 lbs (12.3 kN)

Exciter Speed 5240 vpm 5350 vpm 5240 vpm


Travel Speed up to 83 ft/min(25 m/min)

up to 68 ft/min(21 m/min)


Compaction Area 5395 ft2/hr(501 m2/hr)

5440 ft2/hr(505 m2/hr)

6750 ft2/hr(627 m2/hr)

MODEL AP12 AP15 AP18

Plate Size WxL 13 x 22.5 in(33 x 57 cm)

16 x 22.5 in(40 x 57 cm)

18 x 22.5 in(46 x 57 cm)

Operating Weight

No Water134 lb (61 kg)

Full Water152 lb (69 kg)





Engine Honda GX120


Centrifugal Force 1920 lbs (8.5 kN) 2000 lbs (8.9 kN) 2780 lbs (12.3 kN)

Exciter Speed 5240 vpm 5350 vpm 5240 vpm





Compaction Area

5395 ft2/hr(501 m2/hr)

5440 ft2/hr(505 m2/hr)

6750 ft2/hr(627 m2/hr)

Water Tank Capacity

2.3 gal(8.7 l)

2.3 gal(8.7 l)

2.3 gal(8.7 l)

V I B R A T O R Y P L A T E S 1 0 0 0 S E R I E S

OPTIONAL WHEEL KIT OPTIONAL UHMW PAD

1 0 0 0 S E R I E S

MBW’s advancements in vibratory plates have revolutionized the field over the past 50 years. Each model offers a unique combination of frequency, centrifugal force, amplitude and mass that have doubled productivity, dramatically reduced maintenance, and extended product life.

Unsurpassed exciter quality including extra heavy duty housings, precision ground eccentric shafts, oversized application matched bearings, oil mist lubrication system and custom lubricants to withstand high operating temperatures.

Application matched quality shock mounts and double isolated guide handles.

This series of economical vibratory plates, the 12, 15 & 18, are portable, and offer outstanding compaction performance. A patented suspension system that places shock mounts in a predominantly shear mode at the high amplitude front end of the plate and a predominantly compressive mode at the low amplitude trailing end of the plate. This system reduces hand arm vibration and also better isolates all upper mass components, including the engine, from vibrations


* Clean sand, optimum moisture. MBW recommends that lifts not exceed 12”.( ) Metric Measurements. Specifications subject to change without notice.

SING

LE D

IREC

TION

VIBR

ATOR

Y PLA


The GP2000 is a permutation of the AP2000 where frequency, amplitude, centrifugal force and mass are adjusted to provide optimal productivity in the compaction of sands and gravel. The GP2000 is capable of achieving excellent densities on lifts of granular soils up to 12” (30 cm)*.

Standard with Honda engine

Optional UHMW paving pad accessory for interlocking paving blocks

Optional wheel kit

MBW’s AP2000 was the first vibratory plate compactor specifically designed for asphalt applications. Frequency, amplitude, centrifugal force and mass are all established at optimal levels for maximum productivity on asphalt.

Further, the mechanical construction of the AP2000 is specific to this very demanding application. Stress relieved steel plates are crack resistant and provide long wear. Aluminum exciter housing dissipates heat rapidly and custom lubricants preserve bearing and seal integrity. The self cleaning plate prevents asphalt build-up.

Standard with Honda engine

Optional UHMW paving pad accessory for interlocking paving blocks

Optional wheel kit


MODEL AP2000 AP2018

Plate Size WxL 20 x 22 x 21 in(51 x 56 x 53 cm)

20 x 22 x 18 in(51 x 56 x 46 cm)

Operating Weight

No Water 168 lb (76 kg)

Full Water 193 lb (88 kg)



Engine Options Honda GX160

Amplitude (No Water) .082 in (2.08 mm)

Centrifugal Force 2475 lbs (11 kN)

Exciter Speed 4400 vpm



Compaction Area 9000 ft2/hr (836 m2/hr)

Water Tank Capacity 3 gal (11.3 l) 1 gal (4.0 l)

MODEL GP2000

Plate Size WxL 20 x 22 in(51 x 56 cm)

Operating Weight 165 lb (75 kg)

Engine Options Honda GX160

Amplitude .083 in (2.11 mm)

Centrifugal Force 3250 lbs (14.5 kN)





2 0 0 0 S E R I E S 2 0 0 0 S E R I E S

OPTIONAL UHMW PAD

AP2018



The GP3550 is a premium, high production compactor that will run decades with

reasonable maintenanceThe deck features a full roll cage as standard equipment

with provisions for a water tank for asphalt compaction on the

AP3550. The base plate is self-cleaning with an open sided plate design that allows material to flow out and away from the belt/

pulley assembly during operation. Both models provide

reduced hand/arm vibration, full roll cage

protection, enhanced amplitude, faster travel speed and updated yet rugged appearance.

The GP3000-15 is ideal for confined work areas, such as sidewalk, curb and gutter, and narrow trenches. This specialty plate is not a lightweight compactor. Its operating weight is over 200 lbs. (91 kg) and produces compaction depths up to 16 in. (41 cm)* and a travel speed of 120 ft/min (36.6 m/min).


The GP5800 is an upgrade of model GP5500. The GP5800 maintains its predecessor’s outstanding performance characteristics while improving the design in terms of ergonomics, ease of service and product life expectations. Among these are a removable, easily serviced exciter assembly, superior suspension for improved engine isolation, lower hand/arm vibration and standard protective cage surrounding the engine. This high production compactor travels up to 130 ft/min, generates .094 inch amplitude for deep penetration of backfill materials and is unmatched on mid-sized to large commercial and infrastructure applications.

7 0 0 0 S E R I E SThe GP7000 is MBW’s heavy hitter for jobs with difficult soils and deep lifts of up to 30 in. (76 cm)*. Weighing 653 lbs. (296 kg) with low frequency and high amplitude, this hard working vibratory plate outperforms walk-behind rollers on most granular applications. The GP7000 is easy to maneuver and features a central lifting bail for easy lift and transport.

SING

LE D

IREC

TION

VIBR

ATOR

Y PLA


MODEL GP5800 GP7000


26 x 30 in(66 x 76 cm)

Weight 288 lb (131 kg) 653 lb (296 kg)

Engine Honda GX270 Honda GX390

Amplitude .094 in (2.39 mm) .166 in (4.22 mm)

Centrifugal Force 5800 lbs (25.8 kN) 7900 lbs (35.1 kN)

Exciter Speed 4800 vpm 2800 vpm

Compaction Depth* Up to 20 in (51 cm) Up to 30 in (76 cm)

Travel Speed up to 130 ft/min(39.6 m/min)

up to 100 ft/min(30.5 m/min)


13000 ft2/hr(1208 m2/hr)

3 0 0 0 S E R I E S 5 0 0 0 S E R I E S

MODEL AP3550 GP3550 GP3000-15

Plate Size WxL 21 x 22 in (53 x 56 cm) 16 x 20 in(41 x 51 cm)

Weight



226 lbs(103 kg)

202 lbs(92 kg)

Engine Honda GX160




Compaction Depth* Up to 21 in (53 cm) Up to 21 in (53 cm) Up to 16 in (41 cm)



up to 120 ft/min(36.6 m/min)


11550 ft2/hr(1073 m2/hr)

9600 ft2/hr(892 m2/hr)


The GPR 65, 68 and 77 are compact reversible plates ideal for narrow trenches and confined areas.

The GPR65 and GPR68 are also high production plates. Travel speeds to 92 ft/

min are achieved with good compaction conditions and the plates move with ease over irregular lift surfaces. Head-to-head competitive d e m o n s t r a t i o n

quickly establishes the comparative

benefits of the GPR65 and GPR68.



REVE

RSIB

LE V

IBRA

TORY

PLA

TES REVERSIBLE VIBRATORY PLATES

The GPR77 is a 400 pound reversible plate. The simple yet reliable shifting design lowers acquisition cost, is low maintenance and provides a geo-technical benefit in its ability to shift travel direction at constant speed. The GPR77 produces an amplitude of .066 inches, travels up to 86 ft/min and handles all types of essentially granular soils.

HEAVY DUTY SHIFTINGThe heavy duty mechanical shifting mechanism allows for directional changes at full speed. Endurance testing was terminated at 400,000 shifts without system failure – the best result MBW (and very likely any manufacturer) has ever achieved on a reversible plate shifting design.

MODEL GPR77

Plate Size WxL 22 x 26 in (56 x 66 cm)


77H Honda GX270 397 lb (180 kg)

77D Hatz Diesel 1B20 399 lb (181 kg)





Travel Speed up to 86 ft/min (26 m/min)

Compaction Area 9460 ft2/hr (879 m2/hr)

MODEL GPR65 GPR68

Plate Size WxL 15 x 26 in (38 x 66 cm) 18 x 26 in (46 x 66 cm)


65H Honda GX160 325 lb (147 kg)


68H Honda GX160 330 lb (150 kg)


Amplitude .072 in (1.83 mm) .071 in (1.80 mm)




Travel Speed up to 92 ft/min (28 m/min) up to 88 ft/min (27 m/min)

Compaction Area 6900 ft2/hr (641 m2/hr) 7920 ft2/hr (736 m2/hr)

S M A L L R E V E R S I B L E V I B R A T O R Y P L A T E S S M A L L R E V E R S I B L E V I B R A T O R Y P L A T E S


* Clean sand, optimum moisture. MBW recommends that lifts not exceed 12”.** Amplitude based on actual vibratory mass.( ) Metric Measurements

Increased weight, amplitude and travel speed

Powered by GX390 Honda

Easier to shift direction

Protected by a full wrap around roll cage

Lifting bails for ease in handling

Travel speeds are 15 to 20% faster than previous models

Lower hand arm vibration along with simple, convenient, safe controls at operator’s position

Solid steel plates with substantially higher abrasion resistance & strength than cast

Infinitely variable travel speed in forward and reverse directions plus spot compaction

Lower maintenance hydraulic shifting mechanism

Patented design allows for exchange of lower hydraulic shift seal in approximately 30 minutes versus up to 6 hours in competitive designs

Only reversible plate line Made in the USA

MBW’s hydraulic shifting reversible plates solve maintenance problems that have long plagued this product type. MBW exciter systems are vented to prevent damage to shifting seals. Worn shifting seals are readily serviced from the outside of the exciter assembly (patented), eliminating the complicated process of opening and exposing the exciter assembly for service purposes. Maintenance is simplified, service time is reduced dramatically.

All MBW hydraulic reversibles are easy to maneuver, featuring forward and reverse travel, as well as spot compaction. Powered by Honda gas engines, these reversibles have plenty of power to tackle the toughest compaction applications.

MBW advises users to carefully consider which type of compactor best fits the job. If there is sufficient room to maneuver a single direction plate, productivity, cost and maintenance favor the single direction unit. But where maneuverability is key, reversible plates are the answer.

REVE

RSIB

LE V

IBRA

TORY

PLA

TES REVERSIBLE VIBRATORY PLATES

MODEL GPR15-24 GPR15-26


26 x 33 in(66 x 84 cm)


Engine Honda GX390

Fuel Gas







11310 ft2/hr(1051 m2/hr)

Amplitude Range**

.073 - .104 in(1.85 - 2.64 mm)

.071 - .101 in(1.80 - 2.57 mm)

H Y D R A U L I C S H I F T I N G R E V E R S I B L E P L A T E S H Y D R A U L I C S H I F T I N G R E V E R S I B L E P L A T E S

WWW.MBW.COM 17 16 WWW.MBW.COM

ROLL

ER A

TTAC

HMEN

TSROLLER ATTACHM

ENTSIn 2002 MBW discontinued production of walk-behind rollers … our focus shifted to roller attachments for skid-loaders, backhoes and excavators. Our reasoning was straight forward …

P R O D U C T I V I T YIn geo-technical terms, walk-behind rollers are inefficient compactors due to low machine mass. By coupling a vibratory roller with a much heavier host machine, mass is dramatically improved. Moreover, the operating or cycle speed of host machines is faster than self-contained walk-behind rollers. The combined effect of higher mass and faster working speed is a dramatic gain in productivity.

V E R S A T I L I T YMBW’s broad line of compaction attachments covers the full range of soil types and applications. Our static wheels are ideal for cohesive soils and can be converted to vibratory mode if called for. Our heavy duty UVW models features interchangeable 24 and 36 inch padded wheels. Static and vibratory wheels mount via quick connect coupler.

O P E R A T O R S A F E T YOperators run compaction attachments from the protected cab of the host machine and stay out of trenches.

M A I N T E N A N C E / L I F EMBW’s range of compaction attachments are covered by multiple US and international patents. Our patents focus on technical innovations designed to keep these compactors running reliably over their useful life.

C O S TMBW attachments cost substantially less than trench and walk-behind rollers. But the cost analysis only begins there. Productivity is as much as 10 times higher than walk-behind rollers. Maintenance cost are lower. The full cost analysis emphatically recommends compaction attachments... which is why we discontinued our walk-behind and trench rollers in 2002.

R O L L E R A T T A C H M E N T S R O L L E R A T T A C H M E N T S


ROLL

ER A

TTAC

HMEN

TSROLLER ATTACHM

ENTSMBW STATIC COMPACTION WHEELS are built to standards suitable for vibratory compactors. That means heavier bearings (to 1,100,000 lbs. static load), heavier shafts (to 710,000 lbs. shear strength) with a correspondingly heavy frame that supports the wheel at both ends to minimize frame and shaft deformation. Our static compaction wheels are heavily built because they can be converted to vibratory wheels when need arises.

V I B R A T O R Y C O M P A C T I O N W H E E L S MBW pioneered the industry’s first stick-mounted vibratory compaction wheels in the late 1990s. We now have a whole new generation of vibratory compaction wheels. These new wheels feature a redesigned frame that supports the wheel or drum at both ends to reduce stress concentrations, a patented suspension system that protects isolators from damage due to over deflection and exciter operating temperatures that have been significantly lowered.

( ) Metric Measurements

ATS (smooth drum) and ATP (padded drum) models are available in 73 and 84 inch working widths. All models feature hydraulically powered exciter systems lubricated by an oil mist design. All models feature a patented eccentric shaft design that minimizes exciter shaft deflection, lower operating temperatures, and provide MBW attachments with the industry’s lowest incidence of bearing and seal failure. A knockdown blade is integral to the roller frame. Vibrating drums are isolated from the frame minimizing transmission of vibration to the host machine. All models come with a universal quick attach system.

MBW compaction attachments for skid-steer loaders offer contractors and rental yards a cost effective, low maintenance alternative to comparatively high cost self-contained rollers.US Patents

MODEL ATS/ATP73 ATS/ATP84Length 43.3 in (110 cm)

Height/Weight

Smooth 29 in (74 cm) 1940 lbs (880 kg)

Padded 30 in (76 cm) 2080 lbs (943 kg)

Smooth 29 in (74 cm) 2260 lbs (1025 kg)

Padded 30 in (76 cm) 2410 lbs (1093 kg)

Working Width 73 in (185 cm) 84 in (213 cm)


Exciter Speed 3000 rpm

Centrifugal Force 8850 lbs (39.4 kN) 9765 lbs (43.4 kN)

Flow Requirement 10-50 gpm (38-189 Lpm)

Pressure Requirement 1500-3000 psi (103-207 bar)

Hydraulic Connection 1/2” Flat Face Quick Coupling

S K I D S T E E R R O L L E R A T T A C H M E N T S S T A T I C C O M P A C T I O N W H E E L S

WWW.MBW.COM 2120 WWW.MBW.COM( ) Metric Measurements

ROLL

ER A

TTAC

HMEN

TSROLLER ATTACHM

ENTSThis highly versatile range of stick-mounted c o m p a c t i o n wheels are available in interchangeable 24 and 36 inch working widths, padded drum configurations,

and static or vibratory modes. Massive frame supports compaction wheels at both ends to accommodate enormous static and vibratory forces, torque on uneven surfaces and provide maximum life. Shafting and bearings are highest capacity in the industry. Up to 10 times more productive than walk-behind rollers or stick-mounted vibratory plates. Maintenance is low when properly serviced. Recommended for excavators in the 20K to 60K range. Affixed to booms via pin mount adapter.All models standard with integral leveling blade.


E X A 1 8 L & E X A 1 8The EXA18L is a lightweight (1090 lbs) vibratory wheel for large mini-excavators and rubber tired backhoes 12K to 18K pounds.

The EXA18 is a 1,515 lb vibratory wheel with heavier frame and overall construction. This model is recommended for excavators in the 18K to 45K pound range.

Both models feature a frame free drum width of 18 inches. Combining up to 1/2 the static weight of the host machine with vibration at 2600 VPM, these compactors make quick work of compaction requirements on a full range of soil types.

Both models come with integral backfill leveling blade and can be affixed to booms via pin mount adapter.

Static

Vibratory

MODEL EXA18Working Width 18 in (46 cm)

Operating WeightLightweight 1090 lb (494 kg)

Heavyweight 1515 lb (687 kg)

Amplitude Variable with Static Pressure



Flow RequirementLightweight 10-40 gpm (38-151 Lpm)Heavyweight 10-70 gpm (38-265 Lpm)

Pressure Requirement 1500-3000 psi (103-207 bar)

MODEL STATIC VIBRATORY

Working WidthW24 24 in (61 cm)W36 36 in (91 cm)

Operating Weight

W24 1367 lb (620 kg)W36 1750 lb (793 kg)

W24 2386 lb (1082 kg)W36 2829 lb (1283 kg)

Amplitude N/A Variable withStatic Pressure

Centrifugal Force N/A 10,000 lbs

(44.5 kN)

Exciter Speed N/A 3000 vpm

Flow Requirement N/A 10-70 gpm

(38-265 Lpm)

Pressure Requirement N/A 1500-3000 psi

(103-207 bar)

EXA18 STICK-MOUNTED WHEEL ATTACHMENT UVW STICK-MOUNTED WHEEL ATTACHMENT

WWW.MBW.COM 23

BARREL MOUNTED SPRAYERS

The BMS74 and BMS95 mix and spray water based curing and sealing compounds and form release agents for concrete applications. The BMS74 features a 7.5 gpm roller pump and will handle up to 25% solids efficiently. The BMS95 utilizes a 9.5 gpm diaphragm pump for handling heavier particulate loads up to 35%.

Both sprayers are housed in an extra wide, heavy duty protective cage. The sprayers are easily locked to a 55 gallon drum or can be used in conjunction with the optional Easy Load Cart. No lifting is required... heavy 55 gallon drums are simply rolled onto the tilt bed of the Easy Load Cart (optional) and secured with a winch strap. The cart rolls on pneumatic tires and rubber castors for use on green concrete without damaging the slab.

Hose, Gun, Wand & Cart sold separately.

Options

Pressure Gauge (standard on BMS95 only)

Hydraulic Universal Hose with QD fittings available in 25’, 50’ or 100’

Spray Nozzle Kit (2 each of fine, medium and heavy tips)

9’ Spray Wand

Standard or HD Spray Gun

Easy Load Cart


MODEL BMS74 BMS95Pump Roller Diaphragm

Solids Content 25% 35%

Max Flow 7.5 gpm (28.3 lpm) 9.5 gpm (36 lpm)

Max Pressure 300 psi (20.7 bar) 550 psi (38 bar)

Adjustable Pressure Settings Yes

Std. Operating Pressure 100 psi (6.8 bar)

Weight 95 lb (43 kg) 115 lb (52 kg)

Size 27 x 16 x 17 in (69 x 41 x 43 cm)

Engine Honda GX120 Honda GX160

Quick Disconnect Yes

B A R R E L M O U N T E D S P R A Y E R SC O N C R E T E

B A R R E L M O U N T E D S P R A Y E R SW A L K - B E H I N D P O W E R T R O W E L S

R I D E - O N P O W E R T R O W E L S

B L I T Z S C R E E D ® V I B R A T O R Y T R U S S S C R E E DM O R T A R M I X E R S

S C R E E D E M O N ™ V I B R A T O R Y W E T S C R E E DS L I P F O R M P A V E R S

22 WWW.MBW.COM

Shown with optional cart


WALK-BEHIND TROW

ELSW A L K - B E H I N D P O W E R T R O W E L S

WAL

K-BE

HIND

TRO

WEL

STo function properly, power trowels must maintain a precise perpendicular relationship between the gearbox’s output shaft and blade arms. Once that relationship is compromised, the trowel will vibrate and/or wobble. MBW has gone to great lengths to maintain this critical relationship.

MBW WALK-BEHIND POWER TROWELS feature the industry’s heaviest bearings, output shafts, gears, spiders and blade arms. Comparison of these critical MBW components to those of any competitor answers the question as to why MBW trowels run so well for so long.

Patent pending Low Vibration handle is multi axis shock mounted to reduce operator fatigue

Tool free height adjustable operator handle

ISO compliant, low profile guard ring allows for easy cleaning and blade changes

Standard edger for close finishing

Patent Pending

MODEL F24 F30

Engine OptionsHonda GX120 (114 lb/64 kg)

3 HP Motor Single Phase 220V (126 lb/57 kg)

Honda GX120(128 lb / 58 kg)

Ring Diameter 24 in (61 cm) 30 in (76 cm)

Trowel Speed 70-125 rpm 70-125 rpm

W A L K - B E H I N D P O W E R T R O W E L S

MODEL F36 F46

Engine Options Operating Weight

Honda GX160 183 lb (83 kg)Honda GX270 209 lb (95 kg)

Honda GX270 High Speed 216 lb (98 kg)


260 lb (118 kg)Honda GX390 High Speed

267 lb (121 kg)

Ring Diameter 37.5 in (95 cm) 47.6 in (121 cm)

Blade Sweep Dia. 35.5 in (90 cm) 46 in (117 cm)

Trowel Speed 70-135 rpm35-180 rpm High Speed

70-135 rpm35-180 rpm High Speed

Low Vibration Handle Height 35.8” Min - 43.3” Max

Noise Level 85-105 dBA

( ) Metric Measurements ( ) Metric Measurements

LOW VIBRATION HANDLE

ROTATING GUARD RING FOLD DOWN HANDLE

The F24 & F30 EDGER TROWELS are ideal for jobs that

require a lightweight, highly maneuverable, professional

finishing tool. These specialty finishing power trowels allow

professional results even when confined areas or weight

restrictions leave other machines

standing idle. Perfect for edging in

the tightest spaces, the F24 Walk

Behind Power Trowel is always

ready when needed.

WWW.MBW.COM 27

With 3 sizes, 5 distinctly different models, and manual or hydraulic steering and a single point lifting bail, MBW LOWRIDERS cover the full range of floating and finishing applications. LOWRIDERS have been in production for over 25 years and played an important role in the pioneering and development of riding trowels. Decades of experience has resulted in the industry’s lowest maintenance line of high performance ride-on trowels. LOWRIDERS are simple machines with far fewer moving parts, the industry’s most reliable drive train, the highest quality components and materials. LOWRIDERS set industry standards for high performance, low maintenance and long life.

M K 8 - 7 5 is the industry’s smallest ride-on trowel. Perfect for large or small jobs, multi-story flooring and as a compliment to large machines that just can’t operate in tight areas. This 460 lb. rider transports in the bed of a pick-up, passes through a 32” doorway, can be used as an edging trowel. Floats and finishes with equal proficiency.

M K 8 - 9 0 is a manual steer, 23.5 hp, 6 foot machine. Excellent for float or finish applications with a low center of gravity for improved operating stability. A clean, easy to service design. A workhorse on typical applications.

M K 8 - 9 1 is the industry’s only hydraulic steer, 23.5 hp, 6 foot machine. Same basic design as MK8-90, but hydraulic steering reduces operator fatigue on long duration applications.

26 WWW.MBW.COM( ) Metric Measurements

M K 8 - 1 2 0 is a manual steer, 31 hp, 8 foot machine. Our most popular North American model. High-speed rotors, low center of gravity, superior lines of sight, protected drive train and easy to service. Another workhorse in floating or finishing applications.

M K 8 - 1 2 1 is also a high-speed, but a hydraulic steer version of the MK8-120. Low center of gravity, ease of operation and service. A low maintenance, long lived product.

MK8-120 High-SpeedManual Steering

RIDE

-ON

TROW

ELS RIDE-ON TROW

ELS

MK8-121 High-SpeedHydraulic Steering

MK8-75Manual Steering

MODEL MK8-75 MK8-90 MK8-91

Engine Honda GX390 Kohler CommandPRO 23.5

Kohler CommandPRO 23.5

Operating Weight 460 lb (209 kg) 655 lb (297 kg) 746 lb (338 kg)

Blades 8

Troweling Path 63 in (161 cm) 76 in (194 cm) 76 in (194 cm)

Fuel Gas

Steering Manual Manual Hydraulic

Rotors 2

Rotor Speeds up to 130 rpm up to 125 rpm up to 125 rpm

MODEL MK8-120 MK8-121

Engine Briggs & Stratton Vanguard 31 High Speed

Briggs & Stratton Vanguard 35 High Speed


Blades 8

Troweling Path 100 in (254 cm)

Fuel Gas

Steering Manual Hydraulic

Rotors 2

Rotor Speeds up to 180 rpm

R I D E - O N P O W E R T R O W E L S R I D E - O N P O W E R T R O W E L S

WWW.MBW.COM 29

BLITZSCREED® is state-of-the art in vibratory truss screeds. The Blitzscreed is set-up and cleaned in roughly half the time of other screeds. Mechanical problems common to other designs are eliminated. All bolted construction eliminates weldment failure. MBW’s offset eccentric shaft/bearing design results in far more uniform vibration across the screed and greatly extends bearing life. The quick coupling method of joining section shafts is fast and eliminates failure of mechanical connectors.

Precision machined, cast A-frames handle stresses in all planes and serve as a built-in fixture for maintaining perfect screed alignment throughout the life of the product.

Blitzscreed sections come in 8’ 4”, 4’ 4” and 2’ 4” lengths and can be combined to produce screeds up to 75 feet (screeds in 25 to 40 foot range most common).

Blitzscreed is available in engine driven or pneumatic models with hand and auto winch options.

MBW POWER WINCHES enhance safe operation with a top mounted engagement lever for instant activation and deactivation. Travel speed is easily adjusted through a simple valve control. The units also have an adjustable relief valve that stops the winches in case of an obstruction. Each end operates independently for maximum maneuverability around columns and other obstacles.

28 WWW.MBW.COM

( ) Metric Measurements. Specifications subject to change without notice.

MECHANICAL BLITZSCREED HYDRAULIC WINCH MANUAL WINCH


AIR BLITZSCREED

MODEL MVS

Length2 ft 4 in (.71 m)

4 ft 4 in (1.32 m) 8 ft 4 in (2.54 m)

Width 15 in (38 cm)

Height 16 in (41 cm)

Weight Per Foot 8.3 lb/ft (12 kg/m)

MODEL AVS

Length2 ft 4 in (.71 m) 4 ft 4 in (1.32 m) 8 ft 4 in (2.54 m)

Width 15 in (38 cm)

Height 16 in (41 cm)

Weight Per Foot 8.9 lb/ft (13.2 kg/m)

Vibration up to 8000 vpm

V I B R A T O R Y T R U S S S C R E E D V I B R A T O R Y T R U S S S C R E E DSC

REED

S SCREEDS

30 WWW.MBW.COM WWW.MBW.COM 31

When MBW develops a new product, we look for deficiencies in products already in the marketplace. Portable wet screeds suffered 4 serious shortcomings:

M E C H A N I C A LWet screeds were prone to high maintenance, especially in drive mechanisms between the engine and exciter. The ScreeDemon employs a simple, durable, low cost rubber isolator to drive the eccentric.

F U N C T I O N A LMost screed and screed bar combinations produce irregular vibration along the length of the screed bar. Not only is the concrete exposed to highly variable levels of vibration but cream levels vary from spot to spot along the screed bar. The back-to-back triangular construction of the ScreeDemon bar is extremely rigid and minimizes variability in the transmission of vibration.

Most screeds bolt to their screed bars. Hardware threads are compromised by the concrete and assembling or removing the screed becomes such a problem that crews often don’t disassemble for cleaning or transport. The ScreeDemon simply clamps to the specially designed bar. No holes to weaken the screed bar. No threads to complicate assembly/disassembly. The ScreeDemon goes together and comes apart in seconds.

O P E R A T O R H E A L T H & S A F E T YAll wet screeds tested by MBW exposed operators to excessive hand/arm vibration. The ScreeDemon’s patented mount retention method enables use of low durometer isolators without loss of operator control. Hand/arm vibration is 50 to 90% lower than competitive screeds.


* 18-24 ft bars require two ScreeDemon power units.( ) Metric Measurements

Extra rigid, double triangular, magnesium screed bar

minimizes variability in vibration

clamps to Screedemon - no holes or hardware through bar

is attached or removed from screed in seconds for cleaning/transport

allows for offsetting of screed for working under protrusions

SCRE

EDS SCREEDS

MODEL WS500Operating Weight 29 lb (13.2 kg)

Engine Honda GX35

Max Rated Power 1.5 hp (1.12 kW) @7000 rpm

Displacement 2.1 in3 (35 cm3)

Fuel Tank Capacity 0.17 gal (0.64 L)

BARS WIDTH WEIGHT17804 4 ft (1.22 m) 8.1 lb (3.7 kg)

17806 6 ft (1.83 m) 12.1 lb (5.5 kg)

17808 8 ft (2.44 m) 16.1 lb (7.3 kg)

17810 10 ft (3.05 m) 20.1 lb (9.1 kg)

17812 12 ft (3.66 m) 24.0 lb (10.9 kg)

17814 14 ft (4.27 m) 28.0 lb (12.7 kg)

17816 16 ft (4.88 m) 32.0 lb (14.5 kg)

17818* 18 ft (5.49 m) 36.0 lb (16.3 kg)

17820* 20 ft (6.10 m) 40.0 lb (18.1 kg)

17824* 24 ft (7.31 m) 47.9 lb (21.7 kg)

S C R E E D E M O N ™ V I B R A T O R Y W E T S C R E E D S C R E E D E M O N ™ V I B R A T O R Y W E T S C R E E D

32 WWW.MBW.COM WWW.MBW.COM 33

Often viewed as a commodity, lower production cost is usually seen as the over-riding goal in mortar mixer manufacturing. It shows – overall mortar mixer quality and life have been deteriorating for the last 30 years.

( ) Metric Measurements. 2” Ball Hitch Standard. ( ) Metric Measurements. 2” Ball Hitch Standard.

MECHANICAL

HYDRAULIC

MOR

TAR

MIX

ERS M

ORTAR MIXERS

MODEL MM121

Batch Capacity 12.0 cu ft (.34 cu m)3.5-4.5 bags

Drum Wrap End Plates 10 gauge 1/4”

Standard Axle 61 in torsion axle

Wheel ST175/80D13 high speed

Size 61 x 88 x 60 in(155 x 224 x 152 cm)

Weight 1230 lb (558 kg)

Charging Height 56 in (142 cm)

Engine Option Honda GX390

Shaft Speed 3300/33 rpm

Drive Hydraulic

Electric Options5 hp, 1 phase 230v

5 hp, 3 phase 230v/460v

Shaft Speed 1725/33 rpm

Drive Hydraulic

MODEL MM60 MM80 MM90 MM120

Batch Capacity6.0 cu ft

(.17 cu m)1.5-2 bags

8.0 cu ft (.23 cu m)2.5-3 bags

9.0 cu ft (.26 cu m)3-3.5 bags

12.0 cu ft (.34 cu m)

3.5-4.5 bags

Drum Wrap End Plates

10 gauge7 gauge

10 gauge7 gauge

10 gauge7 gauge

7 gauge1/4”

Standard Axle 46 in solid axle 61 in torsion axle

Wheel 12 x 4.80 inhigh speed

ST175/80D13high speed



Size46 x 64 x 56 in(117 x 163 x

142 cm)

46 x 67 x 57 in(117 x 170 x

145 cm)

46 x 71 x 57 in(117 x 180 x

145 cm)

61 x 86 x 57 in(155 x 218 x

145 cm)

Weight 650 lb (295 kg) 715 lb (324 kg) 730 lb (331 kg) 985 lb (447 kg)

Charging Height 47 in (119 cm) 49 in (124 cm)

Engine Options

Honda GX160Honda GX240

Honda GX240 Honda GX240 Honda GX390

Shaft Speed 3500/41 rpm3300/39 rpm 3300/39 rpm 3300/39 rpm 3300/39 rpm

Drive V-belts to Gears Enclosed Gearbox

Electric Option 1.5 hp, 1 phase115v/230v

2 hp, 1 phase230v

3 hp, 1 phase230v N/A

Shaft Speed 1725/33 rpm N/A

Drive Chain to V-belts to Gears N/A

M O R T A R M I X E R S M O R T A R M I X E R S

MBW does not sacrifice mixer quality. You may pay a little more for a MBW MORTAR MIXER, but the returns in lower maintenance and longer life are worth consideration.

We’re so confident in the superiority of MBW’s mixers that we simply encourage you to take a look and draw your own conclusions. The things to compare include:


paddle shaft and clamping design

bearing capacity

trunnion and pillow block quality

frame strength

drive gears

belt tension mechanism

drum latch/lock system

drum and grid weldments

engine shroud

front leg design

material types

gauge throughout the mixer


SLIP

FORM

PAV

ERS SLIPFORM

PAVERS

The MBW PAVER slip forms curb, curb & gutter and similar profiles with a level of quality that rivals larger pavers. In commercial parking lots and other applications with tight radii, the MBW Paver out performs larger machines. Cost savings associated with use of the MBW Paver are significant and ongoing. Purchase cost is a fraction of large pavers. Transport is accomplished with a pick-up truck and trailer. Crew size can be held to 3-5 people. Maintenance is low.

* Requires Side Drive Unit( ) Metric Measurements

STYLES C100 CG200*

Hopper Size Options12 in (31 cm) 18 in (46 cm)

24 in (61 cm)30 in (76 cm)36 in (91 cm)

48 in (122 cm)

Max Mold W x H 48 x 18 in (122 x 46 cm)

Max Weight 3360 lb (1524 kg) up to 4215 lb (1912 kg)

Width 65 in (165 cm) up to 116 in (295 cm)

Length 112 in (284 cm)

Pour Speed Range 0-40 ft/min (0-12 m/min)

Travel Speed 0-2.5 mph (0-4 km/h)

Drive Tire Size (4-ply foam filled) 23 x 10.5 in (58 x 27 cm)

Trail Tire Size (4-ply foam filled) 18 x 9.5 in (46 x 24 cm)

Slump Range 1-3 in (2.5-7.5 cm)

S L I P F O R M P A V E R SS L I P F O R M P A V E R SThe MBW Paver bridges the gap between hand forming curbs and slip forming with large machines. Two models are available. The two wheel drive C100 pours up to a 12” or 18” width and a maximum height up to 18”.

The three wheel side drive CG200 slip

forms profiles up to a 12” - 48” wide and up to 18” high parameter. Given a reasonable level of variable control the MBW paver pours a 3’ radii with smaller configuration molds.

While production rates vary and are dependent on mix, grade, and crew proficiency, 1000 to 1500 feet of curb and gutter would represent a typical day’s pour. In the tack-on curb over pavement application, the MBW Paver has the potential to slipform up to 4000 ft/day.


NOTE

S NOTESN O T E S N O T E S

Documents

CONSTRUCTION EQUIPMENT - mbw.com · MORTAR MIXERS 32-33 ... Patented polyethylene slide bearings provide minimal ... (1.37 mm) .067 in (1.72 mm) Centrifugal Force: 1920 lbs (8.5 kN)