4
Console and Telnet Passwords Follow these steps to configure console passwords. Note: Before performing this test, ensure that you have an alternate connection into the router, such as Telnet or dial-in, in case there is a problem logging back in to the router. Step 1. From the privileged EXEC (enable) prompt, enter configuration mode ((config)) and then switch to line configuration mode ((config-line), by issuing the following commands: Note: Notice that the prompt changes to reflect the current mode. router#conf t !--- Enter configuration commands, one per line. End with CNTL/Z. router(config)#line con 0 router(config-line)# Step 2. Configure the password, and enable password checking at login. router(config-line)#password router(config-line)#login Step 3. Exit configuration mode. router(config-line)#end router# %SYS-5-CONFIG_I: Configured from console by console Note: Do not save your configuration changes until your ability to log in has been verified. Step 4. Verify the configuration. Examine the configuration of the router to make sure that the commands have been properly entered by issuing the show running- config command.

Console and Telnet Passwords

Embed Size (px)

DESCRIPTION

Cisco ASA

Citation preview

Page 1: Console and Telnet Passwords

Console and Telnet PasswordsFollow these steps to configure console passwords.

Note: Before performing this test, ensure that you have an alternate connection into the router, such as Telnet or dial-in, in case there is a problem logging back in to the router.

Step 1. From the privileged EXEC (enable) prompt, enter configuration mode ((config)) and then switch to line configuration mode ((config-line), by issuing the following commands:

Note: Notice that the prompt changes to reflect the current mode.

router#conf t !--- Enter configuration commands, one per line.End with CNTL/Z. router(config)#line con 0 router(config-line)#

Step 2. Configure the password, and enable password checking at login.

router(config-line)#password router(config-line)#login

Step 3. Exit configuration mode.

router(config-line)#endrouter#%SYS-5-CONFIG_I: Configured from console by console

Note: Do not save your configuration changes until your ability to log in has been verified.

Step 4. Verify the configuration.

Examine the configuration of the router to make sure that the commands have been properly entered by issuing the show running-config command.

To test the configuration, log off the console with the exit command and log in again, using the configured password to access the router.

router#exitrouter con0 is now availablePress RETURN to get started.

Step 5. Save your configuration.

router#write memory

Page 2: Console and Telnet Passwords

Perform these steps to configure Telnet passwords.

Note: Before performing this test, ensure that you have an alternate connection into the router, such as console or dial-in, in case there is a problem logging back in to the router.

Step 1. From the privileged EXEC (or enable) prompt, enter configuration mode (or (config)) and then switch to line configuration mode ((config-line)), by issuing the following commands:

Note: Notice that the prompt changes to reflect the current mode.

router#conf t!--- Enter configuration commands, one per line.End with CNTL/Z.router(config)#line vty 0 4router(config-line)#

Step 2. Configure the password, and enable password checking at login.

router(config-line)#password router(config-line)#login

Step 3. Step 3. Exit configuration mode.

router(config-line)#endrouter#%SYS-5-CONFIG_I: Configured from console by console

Note: Do not save your configuration changes until your ability to log in has been verified.

Step 4. Verify the configuration.

Examine the configuration of the router to make sure that the commands have been properly entered, by issuing the show running-config command.

Test the configuration by making a Telnet connection to the router.

This can be done by connecting from a different host on the network, but you can also do so from the router itself by Telnetting to the IP address of any interface on the router that is in an up/up state as seen in the output of the show interfaces command.

router#telnet

Step 5. Save your configuration.

router#write memory

Follow these steps to configure Auxiliary (AUX) port passwords.

Page 3: Console and Telnet Passwords

Note: before performing this test, ensure that you have an alternate connection into the router, such as console or Telnet, in case there is a problem logging back in to the router.

Step 1. From the privileged EXEC (or enable) prompt, enter configuration mode ((config)) and then switch to line configuration mode ((config-line)), by issuing the following commands:

Note: Notice that the prompt changes to reflect the current mode.

router#conf t!--- Enter configuration commands, one per line.End with CNTL/Z.router(config)#line aux 0router(config-line)#

Step 2. Configure the password, and enable password checking at login.

router(config-line)#password router(config-line)#login

Step 3. Exit configuration mode.

router(config-line)#endrouter#%SYS-5-CONFIG_I: Configured from console by console

Note: Do not save your configuration changes until your ability to log in has been verified.

Step 4. Verify the configuration. Examine the configuration of the router to make sure that the commands have been properly entered by issuing the show running-config command. Test the configuration by making an inbound or outbound connection to the line. For specific information on configuring async lines for modem connections, refer to the:

Modem - Router Connection Guide

Step 5. Save your configuration.