Calgary Office#2, 21 Highfield Circle SECalgary, AlbertaT2G
5N6Phone: (403) 2520070Fax: (403) 2593992
Edmonton Office16304 111 AvenueEdmonton, AlbertaT5M 4G3Phone:
(780) 4862111Fax: (780) 4862155
Vancouver Office#10, 3671 Viking WayRichmond, BCV6V2J5Phone:
(604) 2149453Fax: (604) 2149455Tollfree: (877) 2520070Email:
[email protected]
The process described below only needs to be completed once.
Once configured, the user needs to select 'Start RTK Stream'
through the 'GPSfavorites' to activate the connection to Pleiades
Reference Network.Step Sceeen Menu Instructions Visual
Configuring Pleiades Connection using SmartWorx Viva v4.60 &
CS internal modem
Before you start• Insert the SIM card by removing the black
topcap of the CS15, using thepen to unscrew the locks, you'll see
the SIM card slot below the SD card slot(see right). Insert the SIM
card with the metal chip facing the rear of theCS15, and with the
chamfered end first. Press in until it clicks in place.• Turn on
the CS15, and ensure that the instrument is in a GPS mode. If
not,press Fn>F2, then select one of the GPS modes.• Connect the
CS to the GPS antenna (via. Bluetooth or cable), and placethe
antenna in an place where it will pick up a some satellites.•From
the main menu of SmartWorx, select 'Instrument' > 'GPS Settings'
>'RTK Rover wizard'. Use the following at the prompts.Screen 1.
'Create new profile'.Screen 2. Create a name for the profile (can
be anything).Screen 3. Select 'Internet (e.g.. NTRIP)'.Screen 4.
"Internal 3.5G modem" & make sure UMTS is checked.Screen 5.
Leave PIN/PUK blank.Screen 6. "Using GPRS/CDMA internet
connection".Screen 7. For Rogers SIM, type internet.com for the
APN.For Telus SIM, type sp.telus.com for the APN.Screen 8. Leave
everything unchecked (short wait after pressing next)Screen 9.
'Create server'Screen 10. Enter the following.Server name:
PleiadesAddressL: 75.152.226.181Port: (refer to login email
provided by Pleiades).Check 'Use NTRTIP with this server'.NTRIP
user ID: (refer to login email).NTRIP password: (refer to login
email).
Screen 11. Use 'select mountpoint from source table'Screen 12.
Select 'PDC_SpiderNET' (Alberta), PDC_BC_Nearest (BC), orsingle
base if required.Screen 13. Tick the box 'receive corrections from
RTK network'Network type should be 'nearest'.check 'GGA message'
and leave 'Send user ID' unchecked.Screen 14. RTK Data Format:
'RTCM v3'Leave everything as is. Should be automatically detect and
notick boxes checked.Screen 15. Select 'yes, test my
connection'.Screen 16. Should show all tick boxes if the connection
is OK.Leica GPS favorites is accessed through any screen by
pressing thebutton on the CS15 keyboard. It allows for the
following...• When the instrument is restarted, a connection to
Pleiades needs to be reestablished. Press 'Start RTK stream' to
begin receiving corrections.• Also within this menu is the 'RTK
data link status' icon, which allows theuser to check the status of
the Internet/RTK connection.• You are able to change the
mountpoint/basestation by selecting'Server/Mountpoint', then
pressing F5 'Source' then selecting the new basestation.• To change
to a radio (base & rover) connection, select 'load RTK
profile'and select the radio profile from the list.
1.
2.
3.
4.
5.
RTK RoverWizard
RTK RoverWizard
RTK RoverWizard
Leica GPSFavorites
