Configuration Training ~ Web GUI - Yamaha … (6) Ping is available between . PC1 and PC2 by routing the . different network segments. ... Configuration Training ~ Web GUI ~ Author:

Yamaha Router Configuration Training

~ Web GUI ~

© Yamaha Corporation 2

Equipment

RTX810 SWX2200-8G/24G

GbE ×5, USB 3G modem 1Gbps throughput

200Mbps VPN throughput

IPv6 ready

Withstand up to 50℃

All GbE Cooperation with RTX810

Gigabit VPN Router Smart L2 Switch


Contents

Web GUI operation PPPoE IPsec VPN SWX2200 Control

• Loop Detect •Search Host •VLAN

© Yamaha Corporation

Before training

4

Please disable Windows firewall.

[Start menu] – [Control Panel] – [Windows Firewall] Select “Turn Windows Firewall on or off”.


Access into the Router

192.168.100.1 RTX810 Web browser

http://192.168.100.1/

Username : blank Password : Admin Password ※ If the Admin password is not set, You will keep form blank.


Web GUI Top page


Internet Accessing (PPPoE)

192.168.100.0/24

.1 (LAN)

Internet

■Configure PPPoE Setting for Internet Access

(WAN)

PC


1. PPPoE (1)

Select [Configure provider].


1. PPPoE (2)

The router detects the type of line automatically. Click [Next].


1. PPPoE (3)

“ PPPoE ” is selected. Click [Next].


1. PPPoE (4)

Fill the form with User ID and Connect password. Click [Next].

Router-A ID: user1, PASS: pass1 Router-B ID: user2, PASS: pass2


1. PPPoE (5)

Select “ not specify DNS ” Click [Next].

※ If the provider assigned DNS server address, you will select another radio button and fill the form with address.


1. PPPoE (6)

Check the Information that you selected and filled. Click [Submit].


1. PPPoE (7)

Provider registration is completed and click [Connect].


Top page view after PPPoE setting


2. Check configuration (1)

Select [Advanced settings].



Select “ all configurations ”.



Click “ View in text format ” to show configuration as console format.


2. Check configuration (4) Routing Configuration

PPPoE Configuration

Interface addressing Configuration



Static Filter Configuration



Dynamic Filter Configuration

NAT, DHCP, DNS Configuration


Close the configuration page. Click “ Return to top ” at the bottom of the page.



IPsec VPN (Main Mode)

172.16.1.0/24

Internet (200.1.1.0/24)

IPSec

Router-B

.202 .201

.1 .1

■Configure IPsec VPN (Main Mode) via Internet

172.16.2.0/24

Router-A

PSK: secret PSK: secret

PC2 PC1

1st step: Configure LAN setting 2nd step: Configure IPsec VPN


3. LAN interface addressing (1)

Click [Advanced settings].



Click [Configure LAN].



Fill with LAN interface IP address. Router-A 172.16.1.1 Router-B 172.16.2.1

Fill with DHCP scope ID and IP address range. Router-A 172.16.1.2 - 172.16.1.191 Router-B 172.16.2.2 – 172.16.2.191



Check the parameters are correct.

Click [Execute].



LAN interface IP address and DHCP scope exchange is completed. Pull out the cable of PC and wait for 10 seconds for refresh the PC’s address. Connect the cable to PC. Click “ Access the new IP address via http ”.


4. IPsec VPN (1)

Select [Advanced settings].


4. IPsec VPN (2)

Select [Configure VPN connection].


4. IPsec VPN (3)

Select [Add] on “ Tunnel[01] ”.


4. IPsec VPN (4)

Select “ LAN-to-LAN network over IPsec ”. Click [Next].


4. IPsec VPN (5)

Router A 200.1.1.202 Router B 200.1.1.201

Fill with pre-shared-key. Select “ Identify using IP address ” and fill with opposite router address. Select Authentication and Encryption algorithm. ※ Select same as opposite. Select keepalive use or not.

“ secret ”


4. IPsec VPN (6)

Fill with opposite router’s LAN network address and select net mask. Click [Submit].

Router A Address: 172.16.2.0, netmask: 255.255.255.0 Router B Address: 172.16.1.0, netmask: 255.255.255.0


4. IPsec VPN (7)

IPsec registration is completed and click [Return to top].


Top page view after IPsec setting


4. IPsec VPN (8)

172.16.1.0/24

Internet (200.1.1.0/24)

IPSec

Router-B

.202 .201

.1 .1

172.16.2.0/24

Router-A

PSK: secret PSK: secret

PC2 PC1

Ping is available between PC1 and PC2

172.16.1.2 172.16.2.2


4. Configuration (1)

Routing Configuration

PPPoE Configuration

Added Interface addressing configuration



IPsec VPN Configuration





Dynamic Filter Configuration

NAT, DHCP, DNS Configuration

Added

Added


Switch control

Port1

Port1

Port3

Port24

Port1

Port2

SW1

SW2

RTX810

PC1

PC2

for operation


5. Enable switch control (1)

Web GUI on PC1

Select [Switch control].



Select [Basic configuration].



Select “ Use ” on LAN1.

Click [Submit].



Configure completed. Click [Return to top].


5. Open switch control GUI (1)

Web GUI on PC1

Select [Switch control].


5. Open switch control GUI (2)

Click [Execute] on “ LAN1 ”.


6. Switch control GUI (1)

Click “ View in detail all devices ”, you will see the detail of switch and each port information.



Move pointer onto the switch body and each port. The brief information will be displayed.



The topology change dynamically. Pull out the cable on PORT1, SW2 will disappear. Put back the cable, SW2 will appear.


SW

RTX810

Router sends a proprietary mac frames for switch control regularly to find connected switches. In default: interval time is 3seconds. This frame is used to configure and get status of switches also.


Switch control mechanism



Click the switch’s body: Enable to configure follow: - Name - Firmware update - Power conservation - Loop detection - Port mirroring - Reset frame counter - Restart - Factory default

Configure the switch



Click the switch’s port: Enable to configure follow: - Auto negotiation - Speed - Flow control - QoS - Tag VLAN - Multiple VLAN - Frame counter

Configure the ports


7. Loop detect configuration (1)

Click SW2’s body.



Select [Configure] on “ loop detection ”.



Select “ Automatically shutdown ” and set 300 seconds as port shutdown time. Click [Configure].

※ By default, if the packet loop happened, the switch does not shutdown the loop detected port. The packet loop will remain.



Port1

Port1

Port3

Port24

Port1

SW1

SW2

RTX810

PC1

Make a loop case.



Exclamation mark is displayed on the loop detected port. The switch shutdown the port from bigger number until the packet loop stop. Port shutdown last in 300 seconds. After 300 seconds or pushing MODE button on the front panel, the port will recover from shutdown.


8. Host search (1)

The function to search a host which connected to switch from an IP address or MAC address.

Click [Search for host].


8. Host search (2)

DHCP client list and ARP entry list are displayed. Fill the form with PC2’s IP or MAC address. Click [Search].


8. Host search (3)

The host detected port will blink.


Tagged and Untagged 172.16.1.0/24 (VID : -) 192.168.100.0/24 (VID : 101)

Untagged 172.16.1.0/24

Untagged 192.168.100.0/24

9. VLAN

Port1

Port1

Port3

Port24

Port1

Port2

SW1

SW2

RTX810

PC1

PC2

192.168.100.2

172.16.1.2

LAN1 : 172.16.1.1/24 LAN1/1 : 192.168.100.0/24


9. VLAN (1)

Select “ Create new VLAN tag ”.

Switch control GUI on PC1


9. VLAN (2)

Click router icon.


9. VLAN (3)

Fill with VLAN interface IP address. “ 192.168.100.1/24 ” Click [Configure].


9. VLAN (4)

Click the port that connected with PC2. All ports routing from the router to the selected port is automatically configured as same VLAN group. Click [Configure] at the bottom of the page.


9. VLAN (5)

VLAN interface IP address is set to 192.168.100.1/24 The switch joined VLAN is encircled by blue line. Click [back] at the bottom of page.


9. VLAN (6)

Ping is available between PC1 and PC2 by routing the different network segments. It is also possible to make filtering for each VLAN network.

Port1

Port1

Port3

Port24

Port1

Port2

SW1

SW2

RTX810

PC1

PC2

192.168.100.2

172.16.1.2


9. Configuration

① Enable switch control

② VLAN configuration

③ SW1 configuration

④ SW2 configuration

//① //②

//③

//④

・・・ 192.168.100.1/24

© Yamaha Corporation 70 70

Continue to console operation

Documents

Configuration Training ~ Web GUI - Yamaha … (6) Ping is available between . PC1 and PC2 by routing the . different network segments. ... Configuration Training ~ Web GUI ~ Author: