CONDUCTIVITY + DO PORTABLE - nclabs.com DO.pdf · CONDUCTIVITY + DO PORTABLE. ... Self-stirring Polarographic BOD probe O-086030 1494.90 * Probe included in this package is a self-stirring,

www.nclabs.comOrder Toll Free 1.800.648.7836

Upgraded version of the Model 85. Completely waterproof. Rugged 4-electrode conductivity sensor is built into the cable. Choose polarographic or galvanic sensor. Cable lengths from 1-30 meters (3-90 ft.). 3-year meter warranty. 2-year cable warranty. YSI-2030 726.75/ea (meter only)

Cable for Pro2030

1 m 4 m 10 m 20 m 30 m

YC-2030-1593.75

YC-2030-4608.00

YC-2030-10655.50

YC-2030-20707.75

YC-2030-30802.75

DISSOLVED OXYGEN SENSOR TYPE POLAROGRAPHIC OR GALVANIC Range: 0 to 50 mg/lAccuracy: 0 to 20 mg/l (± 2% of the reading or 0.2 mg/l, whichever is greater) 20 to 50 mg/l (± 6% of the reading)Resolution: 0.1 or 0.01 mg/l (user selectable); 0.1% air saturationCalibration: 1 point and zeroGalvanic DO YP-5202 175.75Polarographic DO YP-5203 175.75

YSI PRO2030 PORTABLE DO/CONDUCTIVITY METER

CONDUCTIVITY + DO PORTABLE

www.nclabs.com Order Toll Free 1.800.648.7836

By now, most of you are aware of the optical technology for measuring DissolvedOxygen. However, the following are a few things you may not be aware of:

* The optical equipment has been on the market for several years now, and hopefully has been “debugged” of all serious problems. However, we caution you to check with your Regulatory Agency to ensure that they will accept data generated with optical DO equipment.

* Warm up time is less than 15 seconds.

* Holds calibration for up to a month. This was stated by a YSI Rep. However, we caution you to follow the protocol designated by your Regulator, or follow the required procedure. In most cases, this will require you to calibrate at least daily or each time you power up the DO measurement system.

* YSI states that the accuracy of the Pro ODO probes are ± 0.1 mg/l, while the accuracy of galvanic probes is ± 0.2 mg/l. However, response time of the optical probe is slower than the galvanic probe (40 seconds for the optical; RH 95% as compared to 18 seconds for the galvanic probe; RH 95%).

* Optical probes require little or no flow past the sensor because they do not consume oxygen during measurement. However, for most laboratory measurements, including BOD, stirring is required as GLP by the procedure and to ensure that the value obtained is representative of the entire contents of the bottle.

* The optical probes do NOT require a filling solution.

* The optical cap for the probe is guaranteed for one year by YSI.

OPTICAL DO


SINGLE CHANNEL METER

• Black and white back-lit display• Three year warranty

YSI-501 (meter only) 1040.25/ea

YSI MULTILAB BENCHTOP OPTICAL DO METERSCan measure Optical DO, pH, ORP, or Conductivity

DOUBLE AND TRIPLE CHANNEL METER

• Large, easy-to-read COLOR display• Three year warranty

Double Channel YSI-502 (meter only) 1415.50/eaTriple Channel YSI-503 (meter only) 1824.00/ea

OPTICAL BOD/DO BENCH

This is YSI’s line of Optical DO for lab use. Meters MUST use the YSI-504 Optical DO probe on the following page, and are not compatible with probes from ProODO series meters. The meters can also accommodate YSI pH and Conductivity probes with automatic probe recognition. These meters can output data to PC’s in various formats, and work well with the optional YSI BOD Analyst Pro Software.


PROBES FOR YSI MULTILAB METERS

OPTICAL BOD PROBE

• YSI Optical DO technology• NO filling solution• Probe cap has a one-year limited warranty• One probe cap included with each BOD probe• No maintenance required, other than annual probe cap replacement• No warm-up time required• Two-year warranty on the probe (excluding cap)

YSI-504 864.50/ea

OPTICAL BOD PROBE CAP

Probe cap for the above

YSI-482 101.65/ea

Please Note: This YSI ODO probe is only compatible with the meters on page 82. Older ODO probes purchased with ProODO series are NOT compatible with these meters.

These IDS sensors automatically store their unique serial number and calibration data. They maintain their calibration data even if moved to another meter. The meter

monitors and graphically displays the condition of the pH probe.

REPLACEMENT PROBES

pH probes for YSI MultiLab meters with 5 ft. cables

Gel-filled, plastic body YSI-411 213.75

Refillable, plastic body YSI-412 247.00

Refillable, glass body YSI-413 308.75

Filling solution for above

8 oz. bottle YSI-413A 20.00/ea

ORP PROBERefillable, glass body, 5 ft. cable

YSI-421 294.50

CONDUCTIVITY PROBEEpoxy body, 10 ft. cable

YSI-431 342.00

YSI-411


YSI BOD ANALYST PRO SOFTWAREConnect meter directly to the PC and BOD Analyst Pro software to take initial and final DO values and let the software eliminate human errors by calculating the BOD/CBOD results. Data can also be entered manually without connection to a computer. For use with YSI instruments, 52, 5000, 5100, Professional Plus, MultiLab, or ProODO. At public cation time, the only Window-supported operating system compatible with this product is Windows 7. This could change. If you have an operating system more recent than Windows 7, please contact NCL before ordering this software.

YSI-120 565.25/ea

YSI OPTICAL DO ACCESSORIES

Optical DO

By now, most of you are aware of the optical technology for measuring DissolvedOxygen. However, the following are a few things you may not be aware of:

* The optical equipment has been on the market for several years now, and hopefully has been “debugged” of all serious problems. However, we caution you to check with your Regulatory Agency to ensure that they will accept data generated with optical DO equipment.

* Warm up time is less than 15 seconds.

* Holds calibration for up to a month. This was stated by a YSI Rep. However, we caution you to follow the protocol designated by your Regulator, or follow the required procedure. In most cases, this will require you to calibrate at least daily or each time you power up the DO measurement system.

* YSI states that the accuracy of the Pro ODO probes are ± 0.1 mg/l, while the accuracy of galvanic probes is ± 0.2 mg/l. However, response time of the optical probe is slower than the galvanic probe (40 seconds for the optical; RH 95% as compared to 18 seconds for the galvanic probe; RH 95%).

* Optical probes require little or no flow past the sensor because they do not consume oxygen during measurement. However, for most laboratory measurements, including BOD, stirring is required as GLP by the procedure and to ensure that the value obtained is representative of the entire contents of the bottle.

* The optical probes do NOT require a filling solution.

* The optical cap for the probe is guaranteed for one year by YSI.


REPLACEMENT PROBES

Description NCL # Price/ea

Field probe 1 m (3 ft.) cable YSI-26A 636.50

Field probe 4 m (12 ft.) cable YSI-26B 650.75

Field probe 10 m (30 ft.) cable YSI-26C 731.50

Field probe 20 m (60 ft.) cable YSI-26D 779.00

For field DO measurement, the YSI field Optical DO system offers several advantages:

• Membrane cap only needs to be changed about once a year• No electrodes to clean or solutions to change• Fast response in calibration and measurement• No flow requirements• IP67 waterproof case• 5000-point datalogging• User-replaceable cables available in many different lengths• Heavy stainless steel probe guard• Meter powered by AC adapter (included), or two alkaline

C-batteries (included)• 3-year warranty on meter; 2-year warranty on probe

YSI OPTICAL FIELD DO PACKAGE Includes:

• Meter• USB saddle• USB interface cable to computer

YSI-626 703.00/ea

* Purchase a probe with your desired cable length from the following table.

YSI OPTICAL FIELD DO SYSTEM

OPTICAL DO FIELD PROBE CAPReplacement cap for YSI Optical Field DO Probe. 1-year warranty.**warranty applies to manufacturing defects only.

YSI-320 99.75/ea

OPTICAL DO PORTABLE

PROBOD OPTICAL SELF-STIRRING PROBESmart Sensor retains calibration in the probe. Does not require warm up or electrode maintenance. Replaceable stir rod. Sensor cap included with initial probe purchase. Two-year warranty on probe and cable.YSI-400 907.25/ea

Stir Shaft for above probe. YSI-626415 42.86/ea

OPTICAL BOD PROBE CAPReplacement cap for YSI Optical BOD Probe. Not for use with YSI Optical Field Probe. 1-year warranty.* *warranty applies to manufacturing defects only.

YSI-482 101.65/ea


OPTICAL DO PORTABLE

YSI® EcoSense ODO200 Optical DOAccurate, economical, handheld dissolved oxygen measurements using optical technology.The EcoSense® line of compact, handheld instruments provides the most accurate data in the most affordable format. The instruments feature an easy-to-use interface, one-hand operation, IP67 waterproof case, and low cost of ownership over the life of the product.The ODO200 simultaneously measures dissolved oxygen, using optical technology, and temperature with the following features:

✭ Automatic temperature compensation

✭ 1-year instrument, cable and sensor cap warranty

✭ 1, 4 and 10-meter durable field cables available

✭ Manual input for salinity and pressure compensation

✭ Low battery indicator with 100 hour battery life

✭ Replaceable optical sensor cap (12-18 month life)

✭ Auto shutoff function after 30 minutes of inactivity

✭ 50 data set reviewable memory

✭ IP67 waterproof rating

The ODO200 is designed for quick, accurate results in an economical platform. The ability to measure DO optically along with temperature, in a simple, compact handheld allows the instrument to be used across multiple application sampling strategies in the field. With a one-year instrument, probe and sensor cap warranty, waterproof case and ease-of-use, the EcoSense ODO200 will fit your needs.

Description NCL # Price

EcoSense, Meter Only YSI-329 318.25

Order MeterStep 1

Order Probe and CableStep 2


EcoSense Optical DO and Temp Field Probe, 1 m Cable YSI-327 565.25EcoSense Optical DO and Temp Field Probe, 4 m Cable YSI-328 565.25EcoSense Optical DO and Temp Field Probe, 10 m Cable YSI-330 646.00

Replacement Parts NCL # PriceReplacement Sensor Cap Kit for EcoSense ODO200 YSI-326 99.75


ORION® STAR A213 BENCHTOP RDO/DO METER ✭ Measures DO and temp

✭ Bright LCD display with ready indication

✭ Automatic barometric pressure compensation

✭ Can be calibrated to Winkler value

✭ Stability indicator

✭ Autoread/hold function

✭ IP54 dustproof and splashproof

✭ 2000-point datalogger, downloadable to printer or computer via an optional RS232 or USB interface

✭ Three-year replacement warranty

✭ AC adapter included* * Can also be operated with four AA batteries

(not included)

Specifications

Concentration 0.00 to 90.00 mg/l

Relative Accuracy ± 0.2 mg/l

% Saturation 0.0 to 600

Salinity Factor 0 to 45 ppt

Barometric Pressure 450-850 mm Hg

Temperature –5 to 105°C

ORION® STAR A213 Benchtop RDO/DO Meter/Accessories NCL # Price

Meter and electrode holder DA-1113 1225.80

DO Kit: meter, electrode holder, O-086030 BOD probe with calibration sleeve, O-080513 probe maintenance kit* DA-1113B 2124.00

Self-stirring Polarographic BOD probe O-086030 1494.90

* Probe included in this package is a self-stirring, polarographic probe. At publication time Orion does not have an optical lab BOD probe that fits this meter.

OPTICAL DO BENCH


Specifications


Relative Accuracy ± 0.2 mg/l





ORION® STAR A223 PORTABLE RDO/DO METER ✭ Measures DO and temp


✭ Automatic barometric pressure compensation



✭ IP67 waterproof


✭ 1000-point datalogger, downloadable to printer or computer via an optional RS232 or USB interface


✭ Operates with four AA batteries (included)* *Optional AC adapter available

ORION® STAR A223 Portable RDO/DO Meter/Accessories NCL # Price

Meter only DA-1213 725.40

Optical DO Field Kit: meter, O-087010 optical DO probe with 3 m (9 ft.) cable, hard carrying case DA-1213A 1460.70

Optional Probes for above meter

Optical DO probe with 3 m (9 ft.) cable O-087010 723.60





Meter and Probe Accessories

Replacement optical cap for above probes O-087001 108.00

Replacement probe guard O-087002 368.60

Calibration sleeve O-087003 143.45

Optional AC adapter for above OA-103 66.80

Hard carrying case for Orion® STAR Portable Meter Series HC-222 138.00

Soft carrying case for Orion® STAR Portable Meter Series SC-333 142.50

Rubber meter boot for Orion® STAR Portable Meter Series RMB-444 104.00

O-087010

OPTICAL DO PORTABLE


THERMO SCIENTIFIC ORION DO PROBEDetermine the DO using any good pH meter. Simple to use, accurate, and no more messing around with loose membranes or filling solutions. Built-in magnetic stir bar. Requires magnetic stir plate for correct operation. Will work with Thermo Scientific Orion, Corning, or any other good pH meter. Not compatible with any optical DO meter or any YSI meter. For laboratory use only, not for field use. Includes two bonded membrane caps which usually last 3 to 6 months each.

Connector Type BNC

NCL # DO-891

Orion # 970899

Price 1234.80/ea

Replacement Parts for Thermo Scientific Orion DO ProbeDescription Orion # NCL # Price/ea

Bonded Membrane Cap 970801 DO-892 73.15

Batteries 970803 DO-893 4.50

Funnel 970802 DO-894 152.95

THERMO SCIENTIFIC ORION FIELD DO PROBEO-083010MD 750.60/ea

THERMO SCIENTIFIC ORION DO PROBEO-081010MD 522.50/ea

THERMO SCIENTIFIC ORION SELF-STIRRING BOD PROBEO-086030 1494.90/ea

Description For DO Probes... Orion # NCL # Price/ea

DO Maintenance Kit AO-083010MD, O-086030

080513 O-080513 177.65

1 Membrane Cap 080515 O-080515 53.10

DO Maintenance Kit BO-081010MD

080113 O-080113 109.25

3 Membrane Caps 081003 O-081003 111.15

REPLACEMENT PROBES FOR ORION STAR/STAR-A SERIES DO METERS

ORION DO PROBES


Fully Automatic Air Calibration for DO/BOD ➀ Turn meter on, allow to warm up ➁ Press “CALIBRATE” ➂ Press “AutoCal”You have just completed a temperature AND PRESSURE-compensated air calibration! No barometers to read, no calculations to perform, no numbers to enter.

Features: Automatic Temperature AND PRESSURE

compensation Large LCD display is very easy to read Auto Stability indicator Menu-driven operation Built-in 100-point datalogger Compatible with YSI BOD software and

YSI bar-code reader Probe stirrer is powered through meter

YSI MODEL 5100 LABORATORY DO METERThis meter has a built-in calibrateable barometer. The system can be used to give you an automatically temperature AND PRESSURE-compensated air calibration. Internal barometer can be verified and/or recalibrated by the user. Large display shows DO, temperature, pressure, and time on the same screen. Accommodates YSI bar-code reader. When used with YSI-5010 DO probe, stirrer is powered through the meter, eliminating the need for the power cord for the stirrer. Can also be used with YSI 5905, 5730, 5720A, and 5750 DO probes with optional YSI-5011 adapter.YSI-5100 1676.75/ea

SELF-STIRRING BOD PROBE, YSI MODEL 5010Features threaded membrane caps and solid stirring rod, eliminating the need to play around with loose membranes, O-rings, and beater boots. For use with YSI Models 5100 and 5000 only. Not for use with any other DO meters.YSI-5010 646.00/ea

CABLE ADAPTER FOR ADAPTING YSI 5905 PROBE TO 5000 & 5100 DO METERSYSI-5011 95.00/ea

DO BENCH


FIELD PROBE, YSI 5739The standard probe for field DO measurements. Easily removable guard protects the sensor tip. Choose the cable length you desire and purchase it separately. Compatible with YSI Model 50, 50B, 52, 57, and 58 meters.DY-832 346.50/ea

DO PROBE CABLESFor use with YSI 5739 Field Probe.

Cables longer than 10 ft. include reels.

Cable Length NCL # Price/ea

10 feet DY-840 288.75

25 feet DY-841 313.50

50 feet DY-842 370.50

YSI FIELD PROBE WITH SCREW-ON MEMBRANE CAPS

This YSI field probe features screw-on membrane caps instead of loose membranes. All probes have cable attached. Choice of 10, 25, or 50-foot cables. Compatible with YSI Model 50, 50B, 52, 57, and 58 meters. Includes one pack membrane caps (YSI-5906).

Cable Length NCL # Price/ea

10 feet YSI-5239A 503.50

25 feet YSI-5239B 517.75

50 feet YSI-5239C 608.00

NON-STIRRING BOD PROBE, YSI 5750

Fits standard 300 ml BOD bottles. Requires sample agitation with magnetic stirrer for correct operation. Comes with a 5-foot cable and one 5775 membrane kit. Requires optional YSI-5011 adapter for compatibility with Models 5000 and 5100.DY-835 389.50/ea

SELF-STIRRING BOD PROBE, YSI MODEL 5905Features threaded membrane caps and solid stirring rod, eliminating the need to play around with loose membranes, O-rings, and beater boots. Compatible with YSI 50B, 52, 57, 58, and 59 meters. Requires optional YSI-5011 adapter for compatibility with Models 5000 and 5100. Includes cable, six membrane caps (YSI-5906), and a bottle of filling solution.YSI-5905 688.75/ea

SUPPLIES FOR OLDER YSI METERS


YSI PRO20 DISSOLVED OXYGEN METER

Rugged and reliable, the YSI Pro20 provides everything you need in a handheld dissolved oxygen instrument. ✴ User-replaceable cables and sensors ✴ Choose polarographic or galvanic for the field ✴ One Touch Cal allows easy DO calibrations ✴ Automatic barometric pressure compensation

(calibrateable barometer) ✴ Stores 50 data sets ✴ Graphic, backlit display and glow-in-the-dark keypad ✴ Available with 1, 4, 10, 20, 30, and 100 m cable lengths ✴ Tough IP-67, impact-resistant, waterproof case

Size 31/4” x 81/2” x 21/4”

Weight with Batteries 475 grams (1.05 lbs.)

Power 2 alkaline C-cells; low battery indicator

Warranty 3-yr. instrument; 2-yr. cable; 1-yr. Polarographic sensors; 6-mo. Galvanic sensors

Salinity Input Range 0-70 ppt; manual

Specifications Dissolved Oxygen Temperature Barometer

Range 0 to 50 mg/l 0 to 45°C 400 to 999 mm Hg

Accuracy 0.2 mg/l ± 0.3°C ± 3 mm Hg

Resolution 0.01 or 0.1 mg/l 0.1°C 0.1 mm Hg


Pro20 Handheld Instrument YM-20 532.00

Order MeterStep 1

Follow these steps to customize your instrument:

DO PORTABLE

Replacement for YSI model 55



1 m cable for DO/Temp YC-201 237.50

4 m cable for DO/Temp (includes cable management kit) YC-204 251.75




100 m cable for DO/Temp YC-20100 712.50


Galvanic Sensor for any cable YP-5202 175.75

Polarographic Sensor for any cable YP-5203 175.75


Flow cell, 203 ml, with single port adapter YA-3077 380.00/ea

Soft-sided carrying case YA-3075 125.00/ea

Hard-sided carrying case YA-3074 285.00/ea

Cable weight, 4.9 oz., attach to stainless steel probe guard YA-5978 27.00/ea

1.25 mil PE membranes for galvanic (6 yellow caps & solution) YSI-5913 60.00/pk

1.25 mil PE membranes for polarographic (6 yellow caps & solution) YSI-5908 57.00/pk

2 mil PE membranes for galvanic (6 blue caps & solution) YSI-5914 60.00/pk

2 mil PE membranes for polarographic (6 blue caps & solution) YSI-5909 57.00/pk

Replacement storage sleeve YSI-5974 4.82/eaProSeries probe maintenance kit. Includes: port plug, grease, o-rings for sensors and cal cup YSI-5745 32.00/ea

Order CableStep 2

Order Sensor Step 3

Order AccessoriesStep 4

YSI-5974

DO PORTABLE


SOFT-SIDED CARRYING CASEThere is a velcro-grip strap to hold the meter in place, an open area for cables, membrane kits, and elastic compartments for miscellaneous.YSI-485 32.00/ea

PROBES AND MEMBRANES FOR THE YSI-200A

YSI EcoSense® DO/TEMP METERThis DO meter features a watertight housing, automatic temperature compensation, manual salinity and pressure compensation, low battery indicator, and last (but certainly not least) screw-on membrane caps. The instrument has a one-year warranty. Probes are available for purchase separately.YSI-200A (meter only) 275.50/ea


DO/Temp probe with 12 ft. cable DY-2004 294.00

DO/Temp probe with 30 ft. cable DY-2010 313.50Six screw-on membrane caps & 1 bottle of fill solution YSI-5908 57.00

Range Resolution Accuracy

Temp. -6 to 46°C 0.1°C ± 0.3°C

DO 0 to 20 ppm 0.01 ppm ± 2%

DO PORTABLE


ORION® STAR A216 BENCHTOP pH/RDO/DO METER

✭ Measures DO, pH, and Temp


✭ IP54 dustproof and splashproof


✭ 2000-point datalogger which is downloadable to printer or computer via an optional RS232 or USB interface accessory


✭ AC adapter included* * Can also be operated with four AA batteries

(not included)

DO✭ Automatic barometric pressure compensation


✭ Stability indicatorpH

✭ Automatic or manual calibration (1 to 5 points)

✭ Automatic buffer recognition

DO


Relative Accuracy 0.2 mg/l





pH

Range 0.0 to 14

Resolution 0.1 / 0.01 / 0.001

Relative Accuracy ± 0.002

Specifications

ORION® STAR A216 Benchtop pH/RDO/DO Meter/Accessories NCL # Price

Meter and electrode holder DA-1116 1381.50

pH/DO Kit: meter, electrode holder, O-8157 pH/ATC triode, O-083005 polarographic DO probe w/ calibration sleeve, buffers, storage and cleaning solutions, DO probe maintenance kit, BOD funnel stirrer and adapter*

DA-1116A 2415.60

ROSS Ultra epoxy refillable pH/ATC triode O-8157 549.10

Polarographic DO probe 1.5 m (4.5 ft.) cable O-083005 711.90

* Probe included in this package is a polarographic probe. At publication time Orion does not have an optical lab DO probe that fits this meter.

DO + pH BENCH


ORION® STAR A326 PORTABLE pH/RDO/DO METER

✭ Measures DO, pH, and Temp

✭ Displays one, two, or all three parameters at once


✭ IP67 waterproof


✭ 5000-point datalogger which is downloadable to printer or computer via an optional RS232 or USB interface accessory


✭ Operates with four AA batteries (included)* *Optional AC adapter available

DO✭ Automatic barometric pressure compensation


✭ Salinity correction

pH✭ Automatic or manual calibration (1 to 5 points)

✭ Automatic buffer recognition


Relative Accuracy 0.2 mg/l





Range 0.0 to 14

Resolution 0.1 / 0.01 / 0.001

Relative Accuracy ± 0.002

ORION® STAR A326 Portable pH/RDO/DO Meter/Accessories NCL # Price

Meter only DA-1216 1122.30

Field pH/RDO/DO Kit: meter, O-8107 pH/ATC triode, O-087010 RDO probe, buffers, storage solution packets, hard carrying case DA-1216A 1994.40

Optional Probes for above meter






Meter and Probe Accessories

Replacement optical cap for above probes O-087001 108.00

Replacement probe guard O-087002 368.60

Calibration sleeve O-087003 143.45

Optional AC adapter for above OA-103 66.80

Hard carrying case for Orion® STAR Portable Meter Series HC-222 138.00

Soft carrying case for Orion® STAR Portable Meter Series SC-333 142.50

Rubber meter boot for Orion® STAR Portable Meter Series RMB-444 104.00

pH

DO

DO + pH PORTABLE

Documents

CONDUCTIVITY + DO PORTABLE - nclabs.com DO.pdf · CONDUCTIVITY + DO PORTABLE. ... Self-stirring Polarographic BOD probe O-086030 1494.90 * Probe included in this package is a self-stirring,