COMPUPRINT SP40 · Ethernet 10/100 Base-T Connection Installation Guide 2 A78410014-004

COMPUPRINT SP40

Ethernet 10/100Base-T ConnectionInstallation Guide

Ethernet 10/100 Base-T Connection Installation Guide

2 A78410014-004

Visit th e web site http://www.compuprint.com for th e lates tinformation,drivers and firmware.

http://www.cpg-i.com/


A78410014-004 3

Table of Contents

Important - READ ME First .................................................... 2Table of Contents ....................................................................... 3Introduction ................................................................................ 5LAN Interface Port...................................................................... 6

LED Indicators ........................................................................ 6Printing Power-On Configuration Setup Page..........................… 7

Windows Environment ..........................................................…. 9Software Installation & Configuration in Windows 98Environment .......................................................................…. 9

Port Installation .............................................................….. 9TCP/IP Protocol - Printer Installation............................... 10TCP/IP Protocol - Port Configuration ................................ 15NetBEUI Protocol - Printer Installation ........................... 19NetBEUI Protocol - Port Configuration ............................ 24

Software Installation & Configuration in Windows 2000Environment .......................................................................... 27

Port Installation ................................................................. 27TCP/IP Protocol - Port Configuration ................................ 28TCP/IP Protocol - Printer Installation............................... 31NetBEUI Protocol - Port Configuration ............................ 35NetBEUI Protocol - Printer Installation ........................... 38

UNIX Environment.................................................................... 42Port Installation & Configuration......................................... 42Linux 7.x & Solaris 7.x Operating Systems ......................... 45

Configuring a Remote Printer for the Red Hot Linux 7.xOperating System .............................................................. 46


4 A78410014-004

Configuring a Remote Printer for the Solaris 7.x OperatingSystem ................................................................................ 46

AS/400 Environment ................................................................ 47Configuring AS/400 for ASCII (TCP/IP protocol) ................. 47

Configuring with ADDTCPIFC.......................................... 47Configuring a Router Definition with ADDTCPRTE ........ 48Configuring a Local Domain and Host Name ................... 48Configuring a TCP/IP Host Table Entry ........................... 48

Configuring AS/400 for Printing ........................................... 49Setting up Printing for ASCII Files................................... 49

Monitoring Printer & Remote Printer Configuration .............. 52Printer Configuration ............................................................ 53NIC Setup. ............................................................................ 54System Settings ..................................................................... . 55Setting the Security Password ........…………….................... 55

FCC Notes................................................................................. 57ICES-003/NMB-003 Notes ........................................................ 57EEC Regulations ...................................................................... 57


A78410014-004 5

IntroductionThe following information concerns the specific characteristicsof the Compuprint printers using the LAN (Local AreaNetwork) connection.

Compuprint printers can be supplied with one Ethernet10/100Base-T port option for LAN connection providing asimple and efficient network printing solution.

For any other printer information, please refer to the printer’s UserManual included in the Documentation & Driver CD-ROM.


6 A78410014-004

LAN Interface Port

The interface ports are located on the rear of the printer:A. Parallel Interface PortB. Serial Interface PortC. LAN Interface Port:

1. Green 10/100Mbit/sec. Transmission Speed Led2. Yellow Traffic Led3. LAN Configuration Page Print Button

LED IndicatorsLED Status Description

Lit Transmission speed at 10Mbit/secGreen Led

Unlit Transmission speed at 100Mbit/sec

Blinks Transmitting or receiving packets fromthe networkYellow Led

Unlit No transmitting or receiving packetsfrom the network

A B

C12

3


A78410014-004 7

P u sh B u tto n

Press on the push button, next to the LAN connector, to printthe LAN interface configuration page. The following shows anexample:


8 A78410014-004

Configuration Page Sample (in TCP/IP protocol)************************************************************

Compuprint Network Interface Configuration************************************************************Printer Information

Product Name: SP40Product Description: Compuprint SP40Printer Base Code: V1.77NIC Code: Version 4.04

NIC Information:General:

Host Name: SP40LANMAC Address: 00:06:6D:00:0E:ACWorkgroup Name: CompuprintLocation: No locationContact: No contact

TCP/IP:IP Address Assignment: DHCPIP Address: 10.0.99.21Subnet Mask: 255.255.0.0Default Gateway: 10.0.255.240

SMTP:SMTP Service: DisabledMail Server Address: 0.0.0.0E-Mail Address (Receiver):E-Mail Address (Sender):

Service InformationSNMP: EnabledHTTP: EnabledSMB (Samba): EnabledFTP: EnabledDirect IP: EnabledTelnet: EnabledLine Printer daemon (LPD): Enabled


A78410014-004 9

Windows EnvironmentIn the Local Area Network printing environment, the PCs canshare a printer, that is, different users can use the sameprinter.Software installation must be carried out on every PC requiringaccess to the Compuprint printer. For the communicationbetween the PCs and the Compuprint printer is necessary thatthe same LAN protocol is used for all connected devices: theTCP/IP or the NetBEUI protocol in a Windows environment

Software Installation & Configuration inWindows 98 EnvironmentPort InstallationCheck that the Printer is powered on and the Green Power led ofthe LAN Interface Port is lit.Insert the CD-ROM labeled Documetation & Driver.1. Run the “Compuprint PP” program from the

Drivers\Microsoft\Print Port directory. The CompuprintPrint Port Install Shield Wizard screen appears:

2. Follow the Compuprint Print Port Setup programinstructions. This program installs the Compuprint printport.


10 A78410014-004

TCP/IP Protocol - Printer Installation

1. Go to “Start-Settings-Printers” on you PC.

2. Invoke the “Add Printer Wizard”. Click Next button. Thefollowing screen appears:

3. Select “Local printer” and click Next button. You will seethe “Printers” list option.


A78410014-004 11

4. If the printer is not listed and the printer comes with theinstallation disk. Click Have Disk button. The “InstallFrom Disk” screen appears:

5. Insert the CD-ROM labeled Documetation & Driver into thedrive. Click Browse button. The “Open” screen appears. Goto the \drivers\microsoft\win98 folders and select thetotal.inf file.

6. Click OK button. The following screen appears:


12 A78410014-004

7. Click OK button. Select “Compuprint SP40” printer.

8. Click Next button. Click the “LPT1” port to use withthis printer and then click Next button again.


A78410014-004 13

9. Type the name for this printer in the “Printer Name”screen. Click Next button.

10. The “Print Test Page” screen appears. If you want to printthe test page, select Yes, then click Finish button to end theprocedure.


14 A78410014-004

If there are not installed Windows 98 files useful to continue thisprocedure in your PC, the following screen appears:

Insert the CD-ROM labeled Windows 98 Second Edition intothe drive. Click OK button to copy the files. When the files arecopied, insert the CD-ROM labeled Documetation & Driver andclick OK button.


A78410014-004 15

TCP/IP Protocol - Port ConfigurationNow configure the port to be connected to the printer.1. Check in “Printers” window if the “Compuprint SP40”

printer is installed. Click on “Compuprint SP40” icon, thenclick on File selection on the menu bar. Select Properties.

2. The “Compuprint SP40 Properties” screen appears:


16 A78410014-004

3. Click Details button. In the screen that appears you canselect the port to be connected to the printer. Click AddPort button.

4. The “Add Port” screen appears. Click “Other” selection.Select “Compuprint Print Port “as the port to use. Click OKbutton.


A78410014-004 17

5. Select “Compuprint Port 9100”. Click OK button to confirm.

6. In the “Port 9100 settings” screen you can configure thisport.

To specify the IP-address see the values set in the INIT IPADDRESS parameter of the LAN INTERFACE item in thePower-On Configuration setup you find in the User Manualincluded in the Printer Documentation & Drivers CD-ROM.Then enter a Port Name in the Port Name field. Click OKbutton to confirm.

If you want to set the default network IP-address and Port Namevalues, click Browse Network button.


18 A78410014-004

7. Click Apply button and then OK button to confirm.

Port configuration is now complete.


A78410014-004 19

NetBEUI Protocol - Printer Installation

1. Go to “Start-Settings-Printers” on you PC.

2. Invoke the “Add Printer Wizard”. Click Next button. Thefollowing screen appears:

3. Select “Local printer” and click Next button. You will seethe “Printers” list option.


20 A78410014-004

4. If the printer is not listed and the printer comes with theinstallation disk. Click Have Disk button. The “InstallFrom Disk” screen appears:

5. Insert the CD-ROM labeled Documetation & Driver into thedrive. Click Browse button. The “Open” screen appears. Goto the \drivers\microsoft\win98 folders and select thetotal.inf file.

6. Click OK button. The following screen appears:


A78410014-004 21

7. Click OK button. Select “Compuprint SP40” printer.

8. Click Next button. Click the “LPT1” port to use with thisprinter and then click Next button again.


22 A78410014-004

9. Type the name for this printer in the Printer Name field.Click Next button.

10. The “Print Test Page” screen appears. If you want to printthe test page, click Yes, then click Finish button to end theprocedure.


A78410014-004 23

If there are not installed Windows 98 files useful to continue thisprocedure in your PC, the following screen appears:

Insert the CD-ROM labeled Windows 98 Second Edition intothe drive. Click OK button to copy the files. When the files arecopied, insert the CD-ROM labeled Documetation & Driver andclick OK button.


24 A78410014-004

NetBEUI Protocol - Port ConfigurationNow configure the port to be connected to the printer.1. Check in “Printers” window if the “Compuprint SP40”

printer is installed. Click on “Compuprint SP40” icon ,then click on File selection on the menu bar. SelectProperties.

2. The “Compuprint SP40 Properties” screen appears.


A78410014-004 25

3. Click Details button. In the screen that appears you canselect the port to be connected to the printer. Click AddPort button.

4. The “Add Port” screen appears. Click “Other” selection.Select “Local Port“ as the port to use. Click OK button.


26 A78410014-004

5. The “Port name” screen appears. Enter a port name in thePort Name field (the port name must be present in the localnetwork as hostname, the print queue as prt1). Click OKbutton to confirm.

\\H ostnam e\prin t que ue_ name

6. Click Apply button and then OK button to confirm.



A78410014-004 27

Software Installation & Configuration inWindows 2000 Environment

Port Installation• Check that the Printer is powered on and the Green Power led

of the LAN Interface Port is lit.

• Insert the CD-ROM labeled Documetation & Driver.

1. Run the “Compuprint PP” program from thedrivers\microsoft\Print Port directory. The CompuprintPrint Port Install Shield Wizard screen appears:

2. Follow the Compuprint Print Port Setup programinstructions. This program installs the Compuprintprint port.


28 A78410014-004

TCP/IP Protocol - Port Configuration1. Go to “Start-Settings-Printers” on you PC.

2. Invoke the “Add Printer Wizard”. The following screen isprompted. Click Next button.

3. The “Local or Network Printer” screen appears, select “Localprinter”.


A78410014-004 29

4. Click Next button and the following screen appears:

Now the wizard detects and installs the new Plug and Playprinters if you want to install the printer manually, click Nextbutton.

5. In the “Select the Printer Port” screen, click on Create a newport field to select “Compuprint Print Port” as the port touse.


30 A78410014-004

6. Click Next button. The “Add New Port” screen appears.Select “Compuprint Port 9100”. Click OK button.

7. The “Port 9100 Settings” screen appears:

To specify the IP-address, see the values set in the INIT IPADDRESS parameter of the LAN INTERFACE item in the Power-On Configuration setup you find in the User Manual includedin the Documentation & Drivers CD-ROM.

Then enter a Port Name in the Port Name field. Click OKbutton to confirm.

If you want to set the default network IP-address and Port Namevalues, click Browse Network button.



A78410014-004 31

TCP/IP Protocol - Printer InstallationNow to install the Compuprint printer to be connected to thenew port, click the OK button of the “Port 9100 Settings”screen.

1. You will see the “Printers” list option. If the printer is notlisted and the printer comes with the installation disk. ClickHave Disk button. The “Install From Disk” screen appears:

2. Insert the CD-ROM Documetation & Driver into the drive.Copy the files from the \drivers\microsoft\Win2000 foldersand select the compprint.inf file.


32 A78410014-004

3. Click OK button. Select “Compuprint SP40”printer.

4. Assign a name for your printer (i.e. Compuprint SP40).


A78410014-004 33

5. To share this printer with the other users, provide a sharename.

6. Click Next button. The “Location and Comment” screenappears. Write the Location and the Comment you desire.


34 A78410014-004

7. Click Next button. The “Print Test Page” screen appears. Ifyou want to see the final printer setting configuration, click

“Yes”.

8. This is the Test Page:

9. Click Finish button to end the printer installationprocedure.


A78410014-004 35

NetBEUI Protocol - Port Configuration1. Go to “Start-Settings-Printers” on you PC.

2. Invoke the “Add Printer Wizard”. The following screen isprompted. Click Next button.

3. The “Local or Network Printer” screen appears, select “Localprinter”.


36 A78410014-004

4. Click Next button and the following screen appears:

Now the wizard detects and installs the new Plug and Playprinters if you want to install the printer manually, click Nextbutton.

5. In the “Select the Printer Port” screen, click on Create anew port to select “Local Port” as the port to use.


A78410014-004 37

6. The “Port name” screen appears. Enter a port name in thePort Name field (the port name must be present in the localnetwork as hostname, the print queue as prt1). Click OKbutton to confirm.

\\H ost nam e\p rin t qu eue_ nam e


38 A78410014-004

NetBEUI Protocol - Printer InstallationNow to install the Compuprint printer to be connected to thisnew port, click on Next button of the “Port Name” screen.

1. You will see “Add Printer Wizard” screen. If the printer isnot listed and the printer comes with the installation disk.Click Have Disk button. The “Install From Disk” screenappears.

2. Insert the CD-ROM Documetation & Driver into the drive.Copy the files from the \drivers\microsoft\Win2000folders and select the compprint.inf file name.


A78410014-004 39

3. Click OK button. Select “Compuprint SP40”printer.

4. Assign a name for your printer (i.e. Compuprint SP40).


40 A78410014-004

5. To share this printer with the other users, provide a sharename.

6. Click Next button. The “Location and Comment” screenappears. Write the Location and the Comment you desire.


A78410014-004 41

7. Click Next button. The “Print Test Page” screen appears. Ifyou want to see the final printer setting configuration, click

“Yes”.

8. This is the Test Page:

9. Click Finish button to end the printer installationprocedure.


42 A78410014-004

Port Installation & ConfigurationCheck that the Printer is powered on and the Green Power led ofthe LAN Interface Port is lit.

It is necessary to be SUPER USER.

Insert the Documetation & Driver CD-ROM.1. From the shell bush, run the “cmpwizard.sh” script

from the drivers\unix directory included in the CD-ROM labeled Compuprint Ethernet LAN. See thefollowing screen:

2. Select the operating system (n.7).


A78410014-004 43

3. Add the IP address. This address must match the IPaddress selected in the INIT IP ADDRESS parameterof the LAN INTERFACE item in the Power-OnConfiguration setup you find in the User Manualincluded in the Printer Documentation & Driver CD-ROM.

4. Enter the Logical Port Name. The Logical Port Name is“prt1”.


44 A78410014-004

5. Enter the Print Server Name. The printer server nameis “ps1”.

6. If this configuration is ok , enter “y” to confirm.

The installation is now complete. If you want to print the testfile, enter the lpr -Pps1 test command.


A78410014-004 45

Linux 7.x & Solaris 7.x Operating SystemsTo configure the printer for the Linux 7.x and Solaris 7.xoperating systems, follow the corresponding proceduredescribed below:

Configuring a Remote Printer for the Red HotLinux 7.x Operating System1. Open the “/etc/hosts” file as root user in a Terminal windows.2. Add the IP address and the Printer Name information.

Here is an example of an “/etc/hosts” file:Ip-address Printer-name10.0.128.220.1 prt110.0.128.220.2 prt2

3. Type “printconf-gui&” from a prompt.4. Click New button. You are asked to enter a queue name for

the printer. Type the queue name you want.5. Then select “Type of queue”. Select Unix Printer (lpd queue)

in the “Queue type” box.6. Insert the printer name used in “/etc/hosts” file (i.e. prt1 or

prt2 ) in the “Server” or “Remote Hosts” box.7. Insert the local spool directory (where the print jobs for the

Unix computer are to be placed) in the “Queue” or “SpoolDirectory” box.

8. Select text only in the “Printer Driver” box. Set up theconfiguration you want and then click OK button.

9. Click File ->Save Changes in the “printconf-gui” window.10. Restart lpd to have (let) the printer daemon receive the new

printer entry.

If the print job is rejected when it is sent to test the printer, ask theremote computer’s administrator to check permission in the

“/etc/lpd.perms” file.


46 A78410014-004

Configuring a Remote Printer for the Solaris 7.xOperating System

1. Open the “/etc/hosts” file as root user in a Terminalwindows.

2. Add the IP address and the Printer Name information.

Here is an example of an “/etc/hosts” file:Ip-address printer-name10.0.128.220.3 prt110.0.128.220.4 prt2

3. Type “admintool&” in a Terminal windows.

4. Select Browse button and then Printers.

5. Select Edit->Add->Access to Print in the “AdmintoolPrinter Menu”.

6. Insert the printer name you want in the “Printer Name”box.

7. Insert the printer name used in “/etc/hosts” file (i.e. prt1or prt2) in the “Printer Server” box.

8. Click Apply and then OK button.

Now you are ready to use the printer.


A78410014-004 47

AS/400 Environment

Configuring AS/400 for ASCII(TCP/IP protocol)

Configuring with ADDTCPIFC

ADDTCPIFC is used to add a TCP/IP interface to AS/400.

This step configures the AS/400 for connection to a TCP/IPnetwork.

1. At the AS/400 command line, enter the followingcommand:

ADDTCPIFCINTNETADR(′127.000.000.000′)LIND(ETHLAN)SUBNETMASK (′255.255.254.000′)

This screen should look like the following one:

Internet address 127.000.000.000.…………………………….. :

Subnet mask 255.255.254.000………………………………… :

Line description ETHLAN………………………………:

To specify the IP-address and the Subnet Mask, see the valuesset respectively in the INIT IP ADDRESS and INIT NET MASKparameters of the LAN INTERFACE item in the Power-OnConfiguration setup you find in the User Manual included inthe Printer Documentation & Driver CD-ROM.


48 A78410014-004

Configuring a Router Definition withADDTCPRTEIf necessary, use the ADDTCPRTE command to create a routedefinition. This is required if the printer is somewhere otherthan on a local segment.

Configuring a Local Domain and Host NameThe AS/400 print commands require a local name and hostname. If you have already configured LAN attached TCP/IPprinters on the AS/400 system, you will have a local domainname and hostname configured on the system.

To configure the local domain, you will run the CFGTCOcommand.

Configuring a TCP/IP Host Table EntryAlthough it is optional to create a TCP/IP host table entry, it issuggested that you take this step. Add the AS/400 name andthe LAN IP address to the “Host Table Entries”.


A78410014-004 49

Configuring AS/400 for PrintingThe procedure for configuring an AS/400 for printing requiresthat you:

1. Setup the printing capability

2. Verify the setup with a print job.

In order to accomplish this configuration, you need thefollowing information:

a) Remote Printer Queue Name

Set for any of ‘pr1’ through ‘pr4’.

The Remote Printer Queue name must be all lower case.

b) IP Address

See the IP Address value set in the INIT IP ADDRESSparameter of the LAN INTERFACE item in the Power-OnConfiguration setup you find in the User Manualincluded in the Printer Documentation & Driver CD-ROM.

Setting up Printing for ASCII FilesThe next step in configuring the AS/400 is to setup the remoteprinting capability. There are two ways to do this:

• you can specify the LPR parameters manually eachtime you send a file to the printer.

• use remote writer and a remote output queue forautomatic printing to the printer.


50 A78410014-004

To Use LPR Manually1. Start TCP/IP, if it not already running, by entering the

STRTCP command

2. At the AS/400 command line, enter ‘LPR’.

3. The following example shows only the parameters youneed to specify:

Remote System RMTSYS INTNETADRPrinter Queue PRTQ d1prn

Destination Type DESTTYP OTHER

Transform SCS to ASCII TRANSFORM YES

Manufacturer Type and MFRTYPMDL IBM6400EPModel

Internet Address INTNETADR 127.000.000.000.

where,

Remote System: enter the host name of your printer orINTNETADR, which then prompts you to specify the IPaddress of your printer.

Printer Queue: set to “pr1” through “pr4”. The remote printerqueue name must be all lower case, entered in single quotes.Destination Type: specify “OTHER” for the DESTTYPparameter.

Transform: specify “YES”.

Manufacturer Type and Model: select a manufacturer type andmodel. Select “IBM6400EP” for Epson emulation or “IBM6400”or “IBM42023” for IBM Proprinter.

Internet Address: specify the IP address of the printer.


A78410014-004 51

To Create an Automatic Remote Output Queue1. From the AS/400 command line, enter CRTOUTQ.

2. The following example shows only the parameters youneed to specify:

Output Queue OUTQ USERNAMERemote system RMTSYS INTNETADRRemote printer queue RMTPRTQ d1prnWriter to Autostart AUTOSRTWTR 1Connection type CNNTYPE IPDestination type DESTTYP XAUTOQXAIXTransform TRANSFORM YESManufacturer type MFRTYPMDL IBM6400EPInternet Address INTNETADR 127.000.000.000

.

where,

Output queue: enter the name of the AS/400 output queue.Remote System: enter the host name of your printer orINTNETADR, which then prompts you to specify the IPaddress of your printer.Remote Printer Queue: set to “pr1” through “pr4”. The remoteprinter queue name must be all lower case, entered in singlequotes.Writer to Autostart: set the value to “1”.Connection Type: specify this value as “IP”.Destination Type: specify “XAUTOQXAIX”.Transform: specify “YES”.Manufacturer Type: select a manufacturer type and model.Select “IBM6400EP” for Epson emulation or “IBM6400PR” or“IBM42023” for IBM Proprinter.Internet Address: specify the IP address of the printer.


52 A78410014-004

Monitoring Printer & Remote PrinterConfiguration

The following procedure describes the use of the InternetBrowser for monitoring the status of the network printer andfor the printer remote configuration. Proceed as follows:

1. To browse the printer web page, enter the IP Address asweb page address or the Host Name.

The IP Address must correspond with the IP Address set in the INIT IPADDRESS parameter of the LAN INTERFACE item, see the User Manualincluded in the Printer Documentation & Driver CD-ROM.

The “Printer Web Page” screen appears:

This Printer Web Page contains the following types ofinformation about network printers:

Printer Configuration: current printer status that you canconfigure by remote control.Printer Status: current ribbon and print head life.Printer Reset: feature to reboot the printer.Product support: reference to contact CPG.


A78410014-004 53

You can select the Printer Configuration, Printer Status, Printer Resetand Product support screens to see the corresponding pagesdescribed in the following sections.

Printer ConfigurationTo obtain the Printer Configuration information tables, clickon the Printer Configuration button. The following screenappears:

This page contains a series of tables with the correspondingprinter set up: For a detailed description of the parameters andvalues contained in the Configuration and Program1/Program2Menus refer to the User Manual.


54 A78410014-004

NIC SetupWhen pressing the NIC Configuration button the followingscreen appears :

You can now choose the network printer configuration.When the parameters are set as necessary, click on theSubmit button at the end of the table.If a password has already been set in the Security item, toenter the remote printer configuration mode, you need to typethe network password.

The User Name is : rootThe default password is : root


A78410014-004 55

SYSTEM SettingClick on the System button. The following page appears:

You can now choose between loading the default factory settingoverwriting the current parameters and setting the securitypassword.

Setting the Security PasswordIn the System page, click on the SecuritySettings button. The first time the following screen appears:


56 A78410014-004

Type the User Name (root) and the password (root) and OKbutton. The following screen appears:

It is now possible to indicate a password to protect the setting.Click on the Submit button, the following screen appears:

Remind you that is necessary to select Reboot printer in the ResetPrinter page to save the changes.


A78410014-004 57

FCC NotesThis equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference when the equipmentis operated in a commercial environment. This equipment generates, uses andcan radiate radio frequency energy and, if not installed and used in accordancewith the instruction manual, may cause harmful interference to radiocommunications. Operations of this equipment in a residential area is likely tocause harmful interference in which case the user will be required to correct theinterference at his own expense.

ICES-003/NMB-003 NotesThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 duCanada.

EEC RegulationsThis is a Class A product. In a domestic environment this product may causeradio interference in which case the user may be required to take adequatemeasures.

This equipment is in compliance with the essential requirements and otherrelevant provisions of the UE Directives 89/336, 73/23, 92/31, 93/68.

Documents

COMPUPRINT SP40 · Ethernet 10/100 Base-T Connection Installation Guide 2 A78410014-004