Compliance with the Essential Health & Safety Requirements

Phone: +44 (0)1702 545125

Fax: +44 (0)1702 546873

E-mail: [email protected]

Web: www.sirco-controls.co.uk

VAT No. 250 2302 20

SIRCO CONTROLS LIMITED

Sweynes Industrial Estate

Ashingdon Road, Rochford

Essex, U.K., SS4 1RQ

Registered in England No. 672489 Registered Office: Charter House, 105 Leigh Road, Leigh on Sea, SS9 1JL

Ref: DoC/E(d) Iss 12

EU DECLARATION OF CONFORMITY No. DoC/E(d)

Category 3 Equipment or Protective System Intended for use in Potentially Explosive Atmospheres DIRECTIVE 2014/34/EU

ATEX II 3G Ex ec nC IIC T6 Gc Ta –20oC to +60oC

Certificate No. Baseefa03ATEX0319X

The EU-Type Examination Certificate and schedules apply to the Sirco Type ATEX Series E(d)

Range of Pressure and Temperature Switches compliant to: EN60079-0:2012+A11:2013, EN60079-15:2010, EN60079-7:2015

The Schedules apply to the variations in material and electrical ratings permitted by the Certifying

Authority.

This EU Declaration of Conformity is issued under sole responsibility of Sirco Controls Ltd who are Approved by SGS-Baseefa 1180 Buxton UK to manufacture and affix the mark (Granted under specific rules) to several products. These products comply with the Certified design and the rules of the ATEX Directive and as such, the presence of the affixed label bearing the mark of SGS-Baseefa 1180 and the Certificate No. is sufficient proof of the Ex Type Examination Certificate and attached schedules existence. It is not, therefore, mandatory to supply copies of these documents. Compliance with the Essential Health & Safety Requirements of the Directive has been assured by SGS-Baseefa against the requirements of EN60079-0:2012+A11:2013, EN60079-15:2010, EN60079-7:2015.

Paul Yeomanson MANAGING DIRECTOR Place: Rochford Date of Issue: 01.07.20

mailto:[email protected]

Certificate Number Issued 17 June 2003 Baseefa03ATEX0319X Page 1 of3

1 TYPE EXAMINATION CERTIFICATE

2 Equipment Intended for use in Potentially Explosive Atmospheres Directive 94/9IEC

3 Type Examination Certificate Baseefa03ATEX0319X Number:

4 Equipment: TYPE ATEX E(d) RANGE OF PRESSURE SWITCHES

5 Manufacturer: SIRCO CONTROLS LIMITED

6 Address: Rochford, Essex, SS4 IRQ

7 This equipment and any acceptable variation thereto is specified in the schedule to this certificate and the documents therein referred to .

8 Baseefa (2001) Ltd. certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of equipment of Category 3 intended for use in potentially explosive atmospheres given in Annex II to European Union Directive 94/9IEC of23 March 1994.

The examination and test results are recorded in confidential Report No . 02(C)0089

9 Compliance with the Essential Health and Safety Requirements has been assured by compliance with:

EN 50021 : 1999

except in respect of those requirements listed at item 18 of the Schedule.

10 If the sign "X" is placed after the certificate number, it indicates that the equipment is subject to special conditions for safe use specified in the schedule to this certificate.

11 This TYPE EXAMINATION CERTIFICATE relates only to the design of the specified equipment and not to specific items of equipment subsequently manufactured.

12 The marking of the equipment shall include the following :

® n 3G EEx nAC nc T6 (Tamb -20°C to +60°C)

This certificate may only be reproduced in its entirety, without any change, schedule included.

Baseefa (2001) Ltd . Customer Reference No. 0997 Project File No. 02/0089

This certificate is granted subject to the general terms and condit ions of Baseefa (200 I) Ltd. It does not necessarily indicate that the equipment may be used in particular industries or circwnstances.

Baseefa (2001) Ltd. Health and Safety Laboratory Site, Harpur Hill,

Buxton, Derbyshire SK17 9JN Telephone +44 (0) 129828255 Fax +44 (0) 129828216

e-mail info@baseefa2001 .biz web site www.baseefa2001 .biz Registered in England No. 4305578 at 13 Dovedale Crescent, Buxton ,

Derbyshire, SK17 9BJ

R S SINCLAIR

DIRECTOR On behalf of

Baseefa (2001) Ltd.

mailto:[email protected]

Certificate Number Issued 17 June 2003 Baseefa03ATEX0319X Page 2 of3

13 Schedule

14 Certificate Number Baseefa03ATEX0319X

15 Description of Equipment

Type ATEX E(d) Range of Pressure Switches rated at 250V a.c. 5A Inductive (O.75PF @ 50Hz), 30V d.c. 3A Inductive (100mH), 30V d.c. 5A resistive comprising a separate pressure unit, switch unit and terminal chamber bolted together to form the pressure switch assembly . All pressure units have the same mating dimensions to fit the switch unit. The pressure assembly may be diaphragm , piston, or bellows operated and in all cases the switch unit is sealed from the pressure unit and is protected against overpressure by a buffer plate.

The pressure chamber of the power unit may be made from Aluminium, Phosphor Bronze, Monel , Titanium, Hastelloy , Aluminium-Bronze, Incolloy, PTFE, PVDF or Stainless Steel and the diaphragm from PTFE, Stainless Steel, Buna N, Teflon FEP, EPDM, Tantalum, Model or Viton, the pistons are Brass and the bellows Stainless Steel.

The movement of the diaphragm, piston or bellows is transmitted into the aluminium switch unit by a push rod and this compresses a range spring which has been pre-stressed by an adjustment screw. Springs with various rates are used to give different pressure ranges . The movement of the push rod is transmitted via a buffer spring to an angle lever which actuates a Honeywell Type 91SEI enclosed-break micro-switch certified as KEMA03ATEXI182U. The switch unit enclosure is sealed by means of an Aluminium cover and a Neoprene gasket.

The micro-switch leads pass via a silicone sealant filled plastic tube and are terminated in a Klippon type MK3/12 terminal block housed in a Klippon type KI terminal enclosure which is mounted on the switch unit. A suitably tapped hole is provided in this enclosure for a cable entry device.

Optionally, two micro-switches may be mounted in the switch unit and either both operated simultaneously by the angle lever or one operated by the angle lever as a warning device and the other operated at a higher pressure by the buffer plate as a switch-off device .

A code for the manufacturer's type reference of the pressure switches including pressure range, pressure chamber material, power unit model and diaphragm material used is shown in Drg No. A3-3978.

Variation 0.1

To allow for Type ATEX E(d) Range of Temperature Switches.

These are almost identical to the pressure switches but have bellows in place of the pressure chamber of the power unit. The bellows are connected to a sensing bulb via a fixed or flexible capillary. To achieve various measurement ranges the bellows-capillary sensor-unit is filled with liquids having different coefficients of expansion .

A code for the manufacturer's type reference of the pressure switches including temperature range, bulb material and capillary type is shown in Drg No. A3-3978 .

Variation 0.2

Alternative thread forms for cable entry device as follows:

M20, % inch E.T., \/2 inch N.P.T. or Pg 13.5

16 Report Number

02(C)0089

17 Special Conditions for Safe Use

1. The ratings on the nameplate must not be exceeded .

2. For pressure switches the diaphragm material must be compatible with the process gas or liquid.

Certificate Number Issued 17 June 2003 Page 3 of3Baseefa03ATEX0319X

3. For temperature switches the T6 temperature class is based on the switch unit temperature only. The sensing bulb temperature will be the same as the maximum range of the process liquid or gas it is sensing.

18 Essential Health and Safety Requirements

All relevant Essential Health and Safety Requirements are covered by the standards listed at item 9.

19 Drawings and Documents

Number Sheet Issue Date Description

AJ-3975 original 01/04/03 GA

A4-3976 original 01/04/03 Label

AJ-3977 1&2 original 01/04/03 Power Units

AJ-3978 original 01/04/03 Coding Guide

Certificate Number Issued 6 July 2007 Baseefa03ATEX0319X11 Page 1 of 2

1 SUPPLEMENTARY TYPE EXAMINATION CERTIFICATE

2 Equipment Intended for use in Potentially Explosive Atmospheres Directive 94/9/EC

3 Supplementary Type Examination Baseefa03ATEX0319X11 Certificate Number:

4 Equipment: TYPE ATEX E(d) RANGE OF PRESSURE SWITCHES

5 Manufacturer: SIRCO CONTROLS LIMITED

6 Address : Rochford, Essex, SS4 IRQ

7 This supplementary certificate extends Type Examination Certificate No. Baseefa03ATEX0319X to apply to equipment designed and constructed in accordance with the specification set out in the Schedule of the said certificate but having any variations specified in the Schedule attached to this certificate and the documents therein referred to.

This supplementary certificate shall be held with the original certificate .

This certificate may only be reproduced in its entirety, without any change, schedule included.

Baseefa Customer Reference No. 0997 Project File No. 07/0307

Thi s certificate is granted subject to the general terms and conditions of Baseefa (2001) Ltd. It does not necessarily indicate that the equipment may be used in particular industries or circumstances.

Baseefa Rockhead Business Park, Staden Lane,

Buxton , Derbyshire SK17 9RZ Telephone +44 (0) 1298766600 Fax +44 (0) 1298 766601

e-mail [email protected] web site www.baseefa .com Baseefa is a trading name of Baseefa (2001) Ltd

Registered in England No. 4305578 at the above address

R S SINCLAIR

DIRECTOR On behalf of

Baseefa (200 I) Ltd.

Certificate Number Issued 6 July 2007 Baseefa03ATEX0319X/1 Page 2 of 2

13 Schedule

14 Certificate Number Baseefa03ATEX0319XJl

15 Description of the variation to the Equipment

Variation 1.1

To confirm that the equipment covered by this certificate has been reviewed against the requirements of EN 60079-0: 2006 and EN 60079-15: 2005 in respect of the differences from EN 50021 : 1999, and that none of these differences in the Standards affect this equipment.

16 Report Number

07(C)0307

17 Special Conditions for Safe Use

None additional to those listed previously


Compliance with the Essential Health and Safety Requirements is not affected by this variation.



Certificate Number Issued 15 July 2013 Baseefa03ATEX0319XJ2 Page 1 of 2

1 SUPPLEMENTARY TYPE EXAMINATION CERTIFICATE

2 Equipment Intended for use in Potentially Explosive Atmospheres Directive 94/9/EC

3 Supplementary Type Examination Baseefa03ATEX0319X12 Cert ificate Number :

4 Equipment: Type ATEX E(d) Range of Pressure Switches

5 Manufacturer: Sirco Controls Limited

6 Address: Rochford, Essex, SS4 1RQ

7 This supplementary certificate extends Type Examinat ion Certificate No. Baseefa03ATEX0319X to apply to equipment designed and constructed in accordance with the specification set out in the Schedule of the said certificate but having any variations specified in the Schedule attached to this certificate and the documents therein referred to.

8 Item 9 of the original Certificate is replaced by "Compliance with the Essential Health and Safety Requirements has been assured by compliance with:

EN60079-0: 2012 EN60079-15: 2010

except in respect of those requirements listed at item 18 of the Schedule."

9 The marking of the equipment has changed from the original Certificate and shall include the following :

® II 3G Ex nA nC IIC T6 Gc Ta -20·C to +60·C

This certificate shall be held with the original certificate and may only be reproduced in its entirety , without any change, schedule included.

Baseefa Customer Reference No. 0997 Project File No. 12/0888

This certificate is granted subject to the general terms and conditions of Baseefa. It does not necessarily indicate that the equipment may be used in particular industries or circumstances. ~U\AJ~

Baseefa roR S SINCLkJ MP()lA.~ Rockhead Business Park, Staden Lane, 11 DIRECTOR

Buxton, Derbyshire SK17 9RZ On behalf ofTelephone +44 (0) 1298766600 Fax +44 (0) 1298 766601 Baseefae-mail info@baseefa .com web site www.baseefa .com

Baseefa is a trading name of Baseefa Ltd Registered in England No. 4305578. Registered address as above.

Certificate Number Issued 15 July 2013 Baseefa03ATEX0319X12 Page 2 of 2

13 Schedule

14 Certificate Number Baseefa03ATEX0319XJ2

15 Description of the variation to the Equipment

Variation 2.1

To confirm that the equipment covered by this certificate has been reviewed against the requirements of EN 60079-0: 2012 and EN 60079-15: 20 lOin respect of the differences from EN 60079-0: 2006 and EN60079-15: 2005, and that compliance is confirmed.

16 Report Number

Baseefa certification report 12(C)0888/ I.

17 Specific Conditions of Use






A3-3975 C 12.06.13 General Assembly

A4-3976 A 13.03.13 Certification Label

Certificate Number Issued 29 July 2016 .. .. Baseefa03ATEX0319X13 • • • Page 1 of 2 •

SUPPLEMENTARY EU - TYPE EXAMINATION CERTIFICATE

2 Equipment or Protective System Intended for use in Potentially Explosive Atmospheres Directive 2014 /34/EU

3 Supplementary EU - Type Examination Certificate Number:

Baseefa03ATEX0319X/3

3.1 In accordance with Article 41 of Directive 20 14/34/EU , EC-Type Examination Certificates referring to 94/9/EC that were in existence prior to the date ofappJication of2014/34/EU (20 April 2016) may be referenced as if they were issued in accordance with Directive 20 I4/34/EU. Supplementary Cert ificates to such EC-Type Examination Certificates, and new issues of such certificates, may continue to bear the original certificate number issued prior to 20 April 2016.

4 Product: Type ATEX E(d) Range of Pressure Switches

5 Man ufactu rer: Sirco Controls Limited

6 Address: Rochford, Essex, SS4 1RQ

7 This supplementary certificate extends EC - Type Examination Certificate No. Baseefa03ATEX0319X to apply to products designed and constructed in accordance with the specification set out in the Schedule of the said certificate but having any variations specified in the Schedule attached to this certificate and the documents therein referred to .

8 SGS Baseefa, Notified Body number 1180, in accordance with Article 17 of Directive 20 14/34/EU of the European Parliament and of the Council, dated 26 February 2014 , certifies that the product, as modified by this supplementary certificate, has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of products intended for use in potentially explosive atmospheres given in Annex II to the Directive.

9 Item 9 of the or iginal Certificate is replaced by "Compliance with the Essential Health and Safety Requirements has been assured by compliance with :

EN60079-0: 2012+All 2013 EN60079-15: 2010 EN60079-7: 2015

except in respect of those requirements listed at item 18 of the Schedule."

12 The marking of the equipment has changed from the orig inal Certificate and shall include the following:

® II 3G Ex ec nC IIC T6 Gc Ta -20°C to + 60°C

SGS Baseefa Customer Reference No . 0997 Project File No. 16/0434

Th is document is issued by the Company subject to its General Conditions for Certification Services accessible at http'llw", w sgs comlenrrerms-a ndCo nditions .as x and the Supplementary Terms and Conditions accessible at http://www sgs co m/SGS BaSC1:faJIerms-and-Cn ndi tions.aspx Attention is drawn to the limitation of liabili ty, indemnification and jurisdiction issues defined therein . Any holder o f this document is adv ised that information contain ed herein reflect s the Company's findin gs at the time of its intervention only and with in the limits of Client' s instruct ions, ifany. It does not neces saril y ind icate that the equ ipment may be used in part icular industries or circumstances. The Company' s sole responsibility is to its Client and this document does not exonerate parti es to a transaction from exercising all their rights and obligations under the transaction docum ents . This document cannot be reproduced except in full, schedule included, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearanc e of this document is unlawful and offend ers may be prosecuted to the fullest extent of the law.

SGS Baseefa Limited Rockhead Business Park, Staden Lane,

Buxton, Derbyshire SK17 9RZ Telephone +44 (0) 1298766600 Fax +44 (0) 1298 766601 WRS~~e-mail [email protected] web site www.sgs.co.uklbaseefa

Regis tered in England No. 4305578. TECHNICAL MANAGER Registered address: Rossmore Business Park, Ellesme re Port, Cheshire, C H65 3EN On behalf of SGS Baseefa Limited

Certificate Number Issued 29 July 2016 Baseefa03ATEX0319XJ3 • • • • • Page 2 of 2•

13 Schedule

14 Certificate Number Baseefa03ATEX0319XJ3

15 Description of the variation to the Product

Variation 3.1

To confirm that the equipment covered by this certificate has been reviewed against the requirements of EN 60079-0 : 20 I2+A I I 2013 , and EN 60079-7: 20 I5 in respect of the differences from EN 60079-0: 20 I2, and EN 60079- 15: 20 I0, and that compliance is confirmed.

16 Report Number

16(C)0434/2

17 Specific Conditions of Use






A4-3976 B 21/07/16 Label Detail For Series ATEX E(d)