Complete machining between centers

TurningHard Turning

GrindingMilling

Machine the entire workpiece in one setup.

With spring loaded center.

● Mechanical clamping system with compensating drive pins● Minimal center runout due to extended guide length on center● Clamping force is transmitted by the tailstock● The center point is mechanically locked when in the clamped position● Accurate within 0.0004” to 0.0008” TIR● High driving torque ● Extended service life of the center and drive pins due to its rigid construction ● Driving diameters from .24” to 6.7”● Work pieces up to 20” in diameter and over 6000 lbs in weight● User friendly and maintenance free operations

FACE DRIVER

Mounting flange with dead true position.

● Safe, reliable and fast mounting options for face drivers● For machine spindles type A2-5; A2-6; A2-8; A2-11; A2-15 and for special spindles ● For all chuck manufacturers● Also available hardened

Type SB with morse taper or straight shank.

Type FSB with flange mount.

Illustration shows driver FSB with mounting flange.

Type ZFMOUNTING ADAPTERS

FACE DRIVER Type FFB

Power operated with fixed center.

● Mechanical clamping system and zero runout center for maximum workpiece support● Fixed center point● Accurate within .00008” to .0002” TIR● High driving torque● Clamping force via actuating cylinder and tailstock ● Extended service life of the center and drive pins due to its rigid construction ● Driving diameters from .24” to 6.7”● Work pieces up to 20” in diameter and over 6000 lbs in weight

Type FFP with driving disk

● For continuously high driving torque● And small driving diameters● Quick change and interchange- able drive disk diameters

Type FFB for hard turning

● Longer life of the drive pins due to the design and coating● Hard turn parts from HRC 58-62

Type FFBR for grinding

● Retractable drive pins● Maximum performance for automated production● Diamond coated drive pins for hard workpieces● Dead zero to the driver flange● Run out accuracy within .00008” to .0002” TIR

Type FBS for grinding

● Simple assembly via morse taper mount● Dead zero to driver head● Run out accuracy within .00008” to .0002” TIR ● Diamond coated drive pins for hard workpieces

Type FFBH

● With hydraulically compen- sated drive pins (no side loads to the center pin)● For highest TIR – demands● Constant datum point ● Drive pins compensate inde- pendently for irregular work- pieces

ULTRA LIVE CENTER Type RN

For best performance with face drivers and high trust operations.

● High rigidity of the center cone● For turning and grinding operations● Designed to withstand high axial and radial loads● Accuracy to within .00008” TIR● Multiple roller bearing design within a sealed housing● Maintenance free● Longer life due to continual improvements and knowledge of live centers

Type RNC extended (or tracer) center point

Type RN-SCH for grinding applications

Type RNW with interchangeable inserts

Type RNA with interchangeable center cones

Form B

Form C

DEAD CENTERS

Type FN Type DIN 806 E (910 11)

Type FNA

Type FNW

Type DIN 806 HE (911 06)Type FNC

Type DIN 807 E (912 11)

Type DIN 807 HE (913 09)

For tubular workpieces.

● Through hardened driving head● Edges re- grindable● Replaceable driving head● With mounting flange for spindle flange or morse taper mount● Large clamping ranges.

PIPE DRIVER Type NDG

● With full carbide point

● With half carbide

● With full carbide point and extraction nut

● With half carbide and extraction nut

Headstock Tailstock

SPECIAL APPLICATIONS Type SFFB

Type FDNC

Pipe driver NDG and tail-stock center support with large cone form.

● Flange mounting morse taper● Spindle mounting flange type ZF with micro adjustment

SFFB Face driver.

● With counter balance weight● Specific workpiece position● Workpiece driven by power actuated drive pins ● For ”Crankshaft” Style parts

FDNC face driver for milling/hobbing.

● With spring loaded center pin● With optional coolant flush

TURN WITH NEIDLEIN

Logansport Matsumoto Company

P.O. Box 7006, 1200 W. Linden Ave., Logansport, IN 46947-7006Phone 574-735-0225 . Fax 574-722-6559www.logan-mmk.com . E-mail info@logan-mmk.com

LMC Your Workholding Solution!