Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
PIMPRI CHINCHWAD
MUNICIPAL CORPORATION
PIMPRI, PUNE.41101 8, MAHARASHTRA Tel: 020-77 425566, Fax O2O-27425600
COMMON SET OF DEVIATIONS
FOR
Request For Proposal (RFP) No: A HO/1/1-2017-18.
NAME OF WORK: Request For Proposal (RFP)
for Renovation of Prof. Ramkrishna More
Auditorium, Chinchwad.
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI, PUNE 411OI8 No: Date:
To, ____________________________ ____________________________ ____________________________ Subject: Request For Proposal (RFP) No: A HO/1/1-2017-18. COMMON SET OF DEVIATIONS (CSD) Dear Sir, Please find enclosed Common Set of Deviations (CSD) along with Annexures for Request For Proposal (RFP) No: A HO/1/1-2017-18. All details other than that covered under Common Set of Deviations remain unchanged. Last date for RFP submission shall Be 07/05/2018 upto15.00Hrs Please note that the changes made herein shall be part and parcel of tender document, which has been binding on the contractor. Thanking you, Yours truly, JOINT CITY ENGINEER (E/M) PCMC, PIMPRI,18.
CONTRACTOR EXCECUTIVE ENGINEER
Request For Proposal (RFP) No: A HO/1/1-2017-18
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI, PUNE-18
NAME OF WORK: Request For Proposal (RFP) for
Renovation of Prof. Ramkrishna
More Auditorium, Chinchwad.
INDEX FOR COMMON SET OF DEVIATIONS
Sr. No.
Brief Description Of Contents Page no.
01 Common Set Of Deviations 1 to 2
02 Appendix A 3
03 Approved Make List 4 to 17
04 Drawings 18 - 35
05 Bar Chart 36
- 4 -
APPENDIX-A
SUBJECT: PRE BID MEETING HELD ON 26/04/2018 AT 11:00 HRS IN THE CHAMBER OF JOINT CITY ENGINEER (E/M), PCMC for
Request For Proposal (RFP) No: A HO/1/1-2017-18 The pre bid conference for the said work was convened by Joint City Engineer(E/M) , PCMC at 11:00 HRS on 26/04/2018. The following officials and prospective bidders were present during the pre bid meeting.
Sr. no. Name Designation
1 Shri. Pravin B Tupe Joint City Engineer (E/M), PCMC
2 Shri. Sanjay Khabde Executive Engineer, PCMC
3 Shri. Vijay Ingulkar Account Officer, PCMC
4 Shri. Chandrakant Muthal Deputy Engineer, PCMC
5 Smt. Lata Babar Deputy Engineer, PCMC
6 Shri. Swapnil Patil Junior Engineer, PCMC
7 Shri. Shyamsunder Bansode Junior Engineer, PCMC
8 Mrs. Sapna Badkar Architect
9 Shri. Sachin Shah Representative of Earthscape Arch & consultant.
10 Shri. Sandesh Gangwal Representative Sandesh Gangwal & Associates
11 Shri. Pradeep Giri Representative of Time Architecture
12 Shri Upendra Purandare Representative of Genesys Tech. P Ltd
Tender No :- Request for Proposal No. Electrical A HO 1/1-2018-19
M/s. Earthscape Architects & Consultants
Sr.
No.
Queries in the tender documentsDecision of PCMC
1 Before accepting 4 months PMC services period, you
are requested to Provide Bar chart showing project
activities to be completed in 4 (four months)
accepted or provided by project contractor
Tentetive Bar Chart is uploaded on
website
2 What if, contractor could not able to complete within
4 months. How PMC will be remunerated then on
extended period of services?
No any extra cost will be paid for
extended time period. PMC should
work up to completion of work.
3 Please provide set of soft/Hard copies of Good for
construction drawing for detail study & Make of items
specified in BOQ.
Approved Makes and drawings
Uploaded on website.
4
Please quote lumpsum amount for the work up to completion
and handing over to PCMC
The Bidder agency should have
quote the total amount of PMC for
this project.
5 Request to modify 1st stage of PMC payment such as
‘10% of the amount quoted in Financial Proposal on
completion of 10% of work’
Not accepted
6 In Snapshot/Technical- 3rd point- ‘Should have rendered
PMC services for at least one project in the last seven
years immediately preceding the bid due date, costing not
less than Rs. 15 Crore’ Shall be read as costing not less
than Rs. 5 Crore’ since every where it is written as 5 Crore.
Shall be read as costing not less
than Rs.5 Crore.
7 Condition of GST registration shall not be binding for
consultantsAs per GST Rule
Time Architecture
1 As it is a time bound project with a high stake we would
like to request that all the drawings and details from all the
consultants are complete and frozen before the
commencement of work, minor changes in the details can
be accommodated if required.
Accepted
2 List of approved brands for all the materials and
equipment’s need to be frozen and updated. As above no. 3
Pimpri Chinchwad Municipal Corporation, Pimpri - 411018
CSD for Prebid meeting on Date 26/04/2018
NAME OF WORK :-Selection of Project Management Consultancy (PMC) for Renovation of
Ramkrishna More Auditorium, Chinchwad
Page 1 of 2
Sr.
No.
Queries in the tender documentsDecision of PCMC
3 Bar chart from all the agencies appointed for the above
mentioned work needs to be finalised as it will help us
stipulate the final BAR chart to monitor the progress of
work more efficiently.
As above no. 1
4 As per the quantum of work observed at site the stipulated
time frame of 4 months will not be sufficient. On set of
monsoon will also affect the time frame to be considered
as the finishing items mentioned in the BOQ as they will
take more time to get the desired outcome. Incase of time
delay what kind of role will the PMC play and what about
the remuneration for the same ?
As above no. 2
1 Payment shall be made in following manner:
• 10% of the amount quoted in Financial
Proposal on completion of 20% of work
• 15% of the amount quoted in Financial
Proposal on completion of 40% of work
• 30% of thearrrotmrquoted in Financial
Proposal on completion of 60% of work
• 30% of the amount quoted in Financial
Proposal on completion of 80% of work
• 15% of the amount quoted in Financial
Proposal on completion of 100% of
work
Not accepted
2 Performance Security - Rs. 1,38,496 (Rupees One Lakh
Thirty Eight thousand four Hundred and Ninety Six only)
&The Successful Bidder shall provide the performance security
of 5% value in Rupees of accepted commercial proposal in
the form of a FDR I bank guarantee (irrevocable) drawn
towards "Commissioner, Pimpri Chinchwad Municipal
Corporation" within 30 (Thirty) days of acceptance of offer in
the form of Letter of Award (LoA) simultaneously before
Signing of Agreement.
Both are liable.
3 Last date of receipt of Bid - Upto 3.00 pm on 07/5/2018. We
request to extend the submission
date by at least one week
extended to 08/05/2018 upto 3.00pm.
***
Sd/- Sd/---
Executive Engineer (Elect) Joint City Engineer (E/M)
A Ward Pimpri Chinchwad Municipal
PCMC., Pimpri 18 Corporation, Pimpri -411018
Last date of submission is extended to 08/05/2018 upto 3.00pm.
M/s. UNISON PROJECT MANAGEMENT PVT. LTD.
Page 2 of 2
Tender No :- Request for Proposal No. Electrical A HO 1/1-2018-19
M/s. Earthscape Architects & Consultants
Sr.
No.
Queries in the tender documentsDecision of PCMC
1 Before accepting 4 months PMC services period, you
are requested to Provide Bar chart showing project
activities to be completed in 4 (four months)
accepted or provided by project contractor
Tentetive Bar Chart is uploaded on
website
2 What if, contractor could not able to complete within
4 months. How PMC will be remunerated then on
extended period of services?
No any extra cost will be paid for
extended time period. PMC should
work up to completion of work.
3 Please provide set of soft/Hard copies of Good for
construction drawing for detail study & Make of items
specified in BOQ.
Approved Makes and drawings
Uploaded on website.
4
Please quote lumpsum amount for the work up to completion
and handing over to PCMC
The Bidder agency should have
quote the total amount of PMC for
this project.
5 Request to modify 1st stage of PMC payment such as
‘10% of the amount quoted in Financial Proposal on
completion of 10% of work’
Not accepted
6 In Snapshot/Technical- 3rd point- ‘Should have rendered
PMC services for at least one project in the last seven
years immediately preceding the bid due date, costing not
less than Rs. 15 Crore’ Shall be read as costing not less
than Rs. 5 Crore’ since every where it is written as 5 Crore.
Shall be read as costing not less
than Rs.5 Crore.
7 Condition of GST registration shall not be binding for
consultantsAs per GST Rule
Time Architecture
1 As it is a time bound project with a high stake we would
like to request that all the drawings and details from all the
consultants are complete and frozen before the
commencement of work, minor changes in the details can
be accommodated if required.
Accepted
2 List of approved brands for all the materials and
equipment’s need to be frozen and updated. As above no. 3
Pimpri Chinchwad Municipal Corporation, Pimpri - 411018
CSD for Prebid meeting on Date 26/04/2018
NAME OF WORK :-Selection of Project Management Consultancy (PMC) for Renovation of
Ramkrishna More Auditorium, Chinchwad
Page 1 of 2
Sr.
No.
Queries in the tender documentsDecision of PCMC
3 Bar chart from all the agencies appointed for the above
mentioned work needs to be finalised as it will help us
stipulate the final BAR chart to monitor the progress of
work more efficiently.
As above no. 1
4 As per the quantum of work observed at site the stipulated
time frame of 4 months will not be sufficient. On set of
monsoon will also affect the time frame to be considered
as the finishing items mentioned in the BOQ as they will
take more time to get the desired outcome. Incase of time
delay what kind of role will the PMC play and what about
the remuneration for the same ?
As above no. 2
1 Payment shall be made in following manner:
• 10% of the amount quoted in Financial
Proposal on completion of 20% of work
• 15% of the amount quoted in Financial
Proposal on completion of 40% of work
• 30% of thearrrotmrquoted in Financial
Proposal on completion of 60% of work
• 30% of the amount quoted in Financial
Proposal on completion of 80% of work
• 15% of the amount quoted in Financial
Proposal on completion of 100% of
work
Not accepted
2 Performance Security - Rs. 1,38,496 (Rupees One Lakh
Thirty Eight thousand four Hundred and Ninety Six only)
&The Successful Bidder shall provide the performance security
of 5% value in Rupees of accepted commercial proposal in
the form of a FDR I bank guarantee (irrevocable) drawn
towards "Commissioner, Pimpri Chinchwad Municipal
Corporation" within 30 (Thirty) days of acceptance of offer in
the form of Letter of Award (LoA) simultaneously before
Signing of Agreement.
Both are liable.
3 Last date of receipt of Bid - Upto 3.00 pm on 07/5/2018. We
request to extend the submission
date by at least one week
extended to 08/05/2018 upto 3.00pm.
***
Sd/- Sd/---
Executive Engineer (Elect) Joint City Engineer (E/M)
A Ward Pimpri Chinchwad Municipal
PCMC., Pimpri 18 Corporation, Pimpri -411018
Last date of submission is extended to 08/05/2018 upto 3.00pm.
M/s. UNISON PROJECT MANAGEMENT PVT. LTD.
Page 2 of 2
Pimpri Chinchwad Municipal Corporation
REQUEST FOR PROPOSAL
Selection of Project Management Consultancy (PMC)
For
Renovation of Ramkrishna More Auditorium, Chinchwad
April 2018
Request for Proposal No. Electrical A HO 1/1-2018-19
PIMPRI CHINCHWAD MUNICIPAL CORPORATION
Request for Proposal No. Electrical A HO 1/1-2018-19
Request for Proposal for the Selection of Project Management Consultancy (PMC) for Renovation of Ramkrishna More Auditorium, Chinchwad
Pimpri Chinchwad Municipal Corporation (PCMC) has built four auditoriums for promoting arts and
culture, Prof. Ramkrushna More Prekshagruha at Chinchwad being one of them (Acharya Atre
Rangmandir Niluphule Natyagruha and Ankushrao Landage Natyagruha being others). PCMC
through this RFP intends to appoint a Project Management Consultancy (PMC) for renovation of
Ramkrishna More Auditorium, Chinchwad.
The consultant for the project will be selected based on the lowest quote submitted for providing
Project Management Consultancy services to PCMC for Post Tender Work of Renovation of
Ramakrishna More Auditorium.
More details about the bid submission procedure and the selection methodology are available in
the Request for Proposal (RFP) document. PCMC thereof invites sealed proposals from firms
having experience as described in the Request for Proposal (RFP) document. Interested Bidders
may download the RFP document in the electronic form only from www.pcmcindia.gov.in from
20/4/2018 onward. However, the cost of such an RFP document i.e Rs. 3000 (Rupees Three
Thousand Only) shall be paid along with the submission of the bids, failing which the bid
submission would not be accepted. The pre-bid meeting for the tender is scheduled on 26/4/2018
at 3.00 pm at the office of Joint City Engineer (E/M) First Floor, Pimpri Chinchwad Municipal
Corporation Office, Pimpri 411018 at 11.00 a.m.
Advt. No. 1236
No.Electrical HO/8/WS/211/2018
Dated 19/4/2018.
Sd/-
Commissioner, PCMC
Selection of PMC for renovation of Ramkrishna More Auditorium, Chinchwad
Request for Proposal
3
PART 1 – REQUEST FOR PROPOSAL
Selection of PMC for renovation of Ramkrishna More Auditorium, Chinchwad
Request for Proposal
4
TABLE OF CONTENTS
TENDER NOTICE: ........................................................................ ERROR! BOOKMARK NOT DEFINED.
1 DISCLAIMER ........................................................................................................................................... 6
2 DEFINITIONS .......................................................................................................................................... 8
3 SNAPSHOT ............................................................................................................................................. 9
4 PROJECT BACKGROUND ................................................................................................................ 11
4.1 PROJECT BACKGROUND ................................................................................................................. 11 4.2 THE SCOPE OF THE PROJECT .......................................................................................................... 11 4.3 PAYMENT AND MILESTONES ............................................................................................................. 12 4.4 THE AGREEMENT OF THE PROJECT ................................................................................................. 12 4.5 CONSULTANT‟S FAILURE TO CARRY OUT INSTRUCTIONS ............................................................... 13
5 DESCRIPTION OF THE SELECTION PROCESS .......................................................................... 14
5.1 SELECTION PROCESS ...................................................................................................................... 14 5.2 STEP 1 RESPONSIVENESS OF BID................................................................................................... 14 5.3 STEP 2 (COVER 1) EVALUATION OF TECHNICAL AND FINANCIAL CAPABILITY .............................. 14 5.4 STEP 3 EVALUATION OF FINANCIAL PROPOSAL ............................................................................ 15 5.5 GENERAL COMPLIANCE CRITERIA .................................................................................................. 15 5.6 IMPORTANT DATES ........................................................................................................................... 15
6 PROCEDURES TO BE FOLLOWED ................................................................................................ 17
6.1 ENQUIRIES & CLARIFICATIONS ....................................................................................................... 17 6.2 AMENDMENTS TO THE RFP ............................................................................................................... 17 6.3 SUBMISSION OF THE BID ................................................................................................................. 17
6.3.1 Technical and financial capability ....................................................................................... 17 6.3.2 Financial Proposal ................................................................................................................. 19 6.3.3 Bidder registration process .................................................................................................. 19
6.4 INITIALLING OF THE BIDS ................................................................................................................. 19 6.5 INSTRUCTIONS TO BIDDERS............................................................................................................. 19 6.6 BIDDER‟S RESPONSIBILITY.............................................................................................................. 20 6.7 VALIDITY OF TERMS OF THE BID ...................................................................................................... 20 6.8 FEES AND DEPOSITS TO BE PAID BY THE BIDDERS........................................................................ 21
6.8.1 Bid Security ............................................................................................................................ 21 6.9 NON ASSOCIATION WITH PROJECT ADVISORS ................................................................................ 21 6.10 CONSEQUENCES OF NOT ADHERING TO THE PROCESS............................................................. 21 6.11 RIGHT TO REJECT THE PROPOSAL ............................................................................................. 21
7 TECHNICAL CAPABILITY EVALUATION....................................................................................... 22
7.1 MINIMUM ELIGIBILITY CRITERIA: TECHNICAL CAPABILITY ............................................................. 22 7.2 MINIMUM ELIGIBILITY CRITERIA: FINANCIAL CAPABILITY ................................................................. 22 7.3 EVALUATION PROCESS ................................................................................................................... 23 7.4 TECHNICAL AND FINANCIAL CAPABILITY INFORMATION FORMATS ................................................ 23
8 FINANCIAL PROPOSAL EVALUATION .......................................................................................... 24
8.1 FINANCIAL PROPOSAL PARAMETERS .............................................................................................. 24 8.2 EVALUATION OF FINANCIAL PROPOSAL .......................................................................................... 24
9 FORMAT OF THE COVERING LETTER .......................................................................................... 25
10 DESCRIPTION OF THE BIDDER .................................................................................................. 26
11 FORMAT OF POWER OF ATTORNEY FOR AUTHORISED REPRESENTATIVE .............. 27
12 FORMAT FOR UNDERTAKING .................................................................................................... 28
13 INFORMATION FORMAT FOR TECHNICAL CAPABILITY ..................................................... 28
14 INFORMATION FORMAT FOR FINANCIAL CAPABILITY ...................................................... 30
15 FINANCIAL PROPOSAL FORMAT .............................................................................................. 31
Selection of PMC for renovation of Ramkrishna More Auditorium, Chinchwad
5
16 FORMAT FOR SEEKING CLARIFICATIONS ............................................................................. 32
17 DESIGN, SPECIFICATION & BOQ FOR THE RENOVATION WORK ................................... 33
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
6
1 DISCLAIMER
The information contained in this Request for Proposal document (the “RFP” or “Request for
Proposal”) or subsequently provided to Bidder(s), whether verbally or in documentary or any other
form by or on behalf of PCMC or any of their employees or advisors, is provided to Bidder(s) on
the terms and conditions set out in this RFP and such other terms and conditions subject to which
such information is provided.
This RFP is not an agreement and is neither an offer nor invitation by PCMC to the prospective
Bidders or any other person. The purpose of this RFP is to provide the Bidders with information
that may be useful to them in preparing and submitting their proposal pursuant to the Bidding
Documents including this RFP (the "Bid"). This RFP includes statements, which reflect various
assumptions and assessments arrived at by PCMC in relation to the Project. Such assumptions,
assessments and statements do not purport to contain all the information that each Bidder may
require. This RFP may not be appropriate for all persons, and it is not possible for PCMC, its
employees or advisors to consider the investment objectives, financial situation and particular
needs of each party who reads or uses this RFP. The assumptions, assessments, statements and
information contained in the Bidding Documents may not be complete, accurate, adequate or
correct. Each Bidder should, therefore, conduct its own investigations and analysis and should
check the accuracy, adequacy, correctness, reliability and completeness of the assumptions,
assessments, statements and information contained in this RFP and obtain independent advice from
appropriate sources.
Information provided in this RFP to the Bidder(s) is on a wide range of matters, some of which
depends upon interpretation of law. The information given is not intended to be an exhaustive
account of statutory requirements and should not be regarded as a complete or authoritative
statement of law. PCMC accepts no responsibility for the accuracy or otherwise for any
interpretation or opinion on law expressed herein.
PCMC, its employees and advisors make no representation or warranty and shall have no liability
to any person, including any Bidder under any law, statute, rules or regulations or tort, principles of
restitution or unjust enrichment or otherwise for any loss, damages, cost or expense which may
arise from or be incurred or suffered on account of anything contained in this RFP or otherwise,
including the accuracy, adequacy, correctness, completeness or reliability of the RFP and any
assessment, assumption, statement or information contained therein or deemed to form part of this
RFP or arising in any way by participating in this Bidding Process.
PCMC also accepts no liability of any nature whether resulting from negligence or otherwise
howsoever caused arising from reliance of any Bidder upon the statements contained in this RFP.
PCMC may in its absolute discretion, but without being under any obligation to do so, update,
amend or supplement the information, assessment or assumptions contained in this RFP.
The issue of this RFP does not imply that PCMC is bound to select a Bidder or to appoint the
Successful Bidder or Operator, as the case may be, for the Project and PCMC reserves the right to
reject all or any of the Bidders or Bids without assigning any reason whatsoever.
The Bidder shall bear all its costs associated with or relating to the preparation and submission of
its Bid including but not limited to preparation, copying, postage, delivery fees, expenses
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
7
associated with any demonstrations or presentations which may be required by PCMC or any other
costs incurred in connection with or relating to its Bid. All such costs and expenses will remain
with the Bidder and PCMC shall not be liable in any manner whatsoever for the same or for any
other costs or other expenses incurred by a Bidder in preparation or submission of the Bid,
regardless of the conduct or outcome of the Bidding Process.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
8
2 DEFINITIONS
Authorised Representative/ Signatory shall mean the person who shall be duly authorized by the
Bidding Company in its RFP submission to sign on the Bid. This designated person shall be
authorised to perform all the tasks including, but not limited to providing information, responding to
enquiries, entering into contractual commitments on behalf of the Bidder.
Bid shall mean the Cover 1 and Financial Proposal submission as defined in Section 6.3, as
submitted by the Bidders in response to this RFP Document.
Bidder means a Bidding Company/ Partnership Firm/ Proprietary Firm that has submitted a Bid in
response to the RFP Document.
Bidding Company If the RFP for the Project is submitted by a single Entity, it shall be referred to
as the “Bidding Company”.
Bid Security shall be a bid security for an amount as mentioned in Section 6.8.1.
Bid Validity Period shall mean a period of not less than 180 days from the last date for submission
of the Proposal and shall also include any extension of bid validity period if asked by Corporation.
Business Entity/ Entity shall mean a company incorporated or registered under the Indian
Companies Act, 1956 / 2013 or any firm registered under Indian Partnership Act 1932, or any
registered Proprietary firm.
Corporation shall mean Pimpri Chinchwad Municipal Corporation.
Request for Proposal / RFP / RFP Document mean this Request for Proposal document
Financial Proposal shall mean the information submitted as per Section 15 of this Document.
Letter of Award (LoA) shall mean the letter issued by the Corporation to the successful bidder.
Project shall mean providing Project Management Consultancy services to PCMC for Post Tender
Work of Renovation of Ramakrishna More Auditorium.
Responsiveness of the Bid/ Non-Responsive shall have a meaning as referred in Section 5.2.
Successful Bidder shall mean the Bidder who inter alia meets the eligibility criteria specified in
section 7 of the RFP and whose financial quote is the lowest.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
9
3 SNAPSHOT
This section provides a snapshot of the RFP Document to the Bidder. The Bidder is expected to read the entire Document for details.
Name of the project Selection of PMC for renovation of Ramkrishna More Auditorium, Chinchwad
Contract period 4 months
Key dates
Pre-bid meeting date
Last date and time for submission
Eligible entities Partnership Firms or Proprietary Firms or Companies providing PMC services
Evaluation Criteria
Financial The firm shall have an Average Annual turnover of at least Rs. 10 lakh (Rupees Ten lakh) from consultancy services, during the last three financial years, immediately preceding the bid due date.
Technical Should have been in existence for at least 7 years
preceding the bid due date
Should have rendered any three mentioned below services related to construction Management & Supervision for Civil, Electrical, HVAC, Acoustical, Advanced sound system works of any one project of auditorium for Government/ Semi-Government clients/ Private
Should have rendered PMC services for at least one project in the last seven years immediately preceding the bid due date, costing not less than Rs. 15 Crore
The bidder shall have to deploy at site, full-time qualified experts (refer section 7.1) throughout the execution of work
Bidding criteria Lowest rate quoted for providing PMC services
Bid security amount Rs. 27,700/- (Rupees Twenty Seven Thousand Seven Hundred only)
Performance Security Rs. 1,38,496 (Rupees One Lakh Thirty Eight thousand four Hundred and Ninety Six only)
Submission of Bid – Contents (to be submitted in hard copy)
Cover 1
1 Payment of Rs. 3000/- (Rupees Three Thousand only) against purchase of RFP document
2 Payment of Rs.27,700/- (Rupees Twenty Seven Thousand Seven Hundred only) as Bid Security
3 Covering Letter as per Section 9
4 Description of the Bidding Company as per Section 10
5 Power of Attorney for the authorised representative as per Section 11
6 Undertaking as per Section 12
7 Information format for technical and financial capability as per Section 13 and Section 14 respectively.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
10
8 Attested copy of PAN Card
9 Attested copy of GST registration
Financial Proposal – The financial quote to be submitted to The Jt.City Engineer (E/M), PCMC only. Tentative format of financial proposal is enclosed in Section 15
Corporation contact details
Address Office of Joint City Engineer (E/M)
1st Floor, PCMC Main Office, Ambedkar Chowk, Pune Mumbai
Highway, Pimpri, Pune – 411018
Telephone 020- 67331421
Fax 020-27425600
Email [email protected] ; [email protected]
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
11
4 PROJECT BACKGROUND
4.1 PROJECT BACKGROUND
Pimpri Chinchwad Municipal Corporation (PCMC) (hereinafter referred as “Corporation”), has built
three auditoriums, Prof. Ramkrushna More Prekshagruha at Chinchwad, Acharya Atre Rangmandir
at Sant Tukaramnagar, Ankushrao Landage Natyagruha at Bhosari. The Auditorium are built to
provide an opportunity to various artists & organizations for promoting drama. Many programs are
organised during the year in these auditoriums.
PCMC has undertaken the project of renovation of Ramakrishna More Auditorium and has
appointed the operator for undertaking the renovation work in 4 month. PCMC is now desirous of
appointing an Agency for the purpose of providing Project Management Consultancy services to
PCMC for Post Tender Work of Renovation of Ramakrishna More Auditorium and hence, invites
proposals from reputed Companies / Firms providing Project Management Consultancy services.
The Consultant shall have to provide comprehensive services of complete day to day supervision,
monitoring and management of the works required for the project, adhering to the respective
contracts’ execution of work as per the approved drawings, specifications subject to such further
variations and modifications as PCMC may decide from time to time.
The Successful Bidder shall be required to deploy a team of expert professionals, details of which
are given in Section 7.1.The proposed team shall be composed of experts and specialists in their
respective areas of expertise and managerial/support staff such that the Consultant should be able
to complete the Consultancy within the specified time schedule of four months (from the date of
issue of work order).
4.2 THE SCOPE OF THE PROJECT
PCMC intends to renovate the Prof. Ramakrishna More Auditorium in Chinchwad. The contractor to
carry out the renovation works has been finalised and as per the Detailed Project Report, the
project cost of the renovation work is estimated at approximately Rs.18.46 Crores. The PMC
consultant shall provide consultancy service for Post Tender Work of Renovation of Prof.
Ramakrishna More Auditorium1. The Time limit for the Consultant shall be 4 (four) months.
The PMC consultant shall have to provide comprehensive services of complete day to day
supervision, monitoring and management of the works required for the project, adhering to the
respective contracts’ execution of work as per the approved drawings, specifications subject to
such further variations and modifications as PCMC may decide from time to time.
The Scope of work for Consultant includes but will not be limited to the following indicative works:
Planning, scheduling and implementing all works i.e. Civil, Electrical, HVAC, Fire, Security,
Solar Energy to complete the project in scheduled time.
To co-ordinate with the Engineer in charge / Architect for the necessary drawings, study
and scrutinize them and point out discrepancies, if any.
Making circuit drawings for the electrical works to be carried out.
Supervise if the contractor has ensured that the acoustics are in-line with the Panels.
Supervise if the contractor has ensured State of Art fire & Smoke Detection System.
Supervise if the contractor has ensured augmentation of HVAC systems.
Supervise the Provision of additional CCTV Cameras for security.
Undertake pre-dispatch inspection, installation supervision of solar power panels and also
monitor generation of solar power after installation.
1 The consultant can procure the Architectural Drawings and schedules from PCMC office.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
12
Shall verify all dimensions of site and ensure that they are as per drawings. Discrepancies,
if any shall be notified to the Corporation immediately.
Shall be responsible for overall supervision and monitoring of the work and shall be
available at site everyday (including nights if the contractor carries out work in shifts to
achieve the project completion schedule).
Shall be responsible for ensuring Contractor abides by the specifications and conditions of
Contract.
Checking the material and equipment used in project execution are as per the
specifications of the Contract.
Shall be responsible to prepare a checklist of the day to day works and all other items as
stipulated in the BOQ are in agreement with the Contract and its supervision.
Preparation of weekly reports relating to time, cost and quality in the format approved by
the Corporation.
Shall co-ordinate with all agencies working at site, liaison with local authorities for
permissions / commencement certificate / completion certificate, etc.
Keep record of dismantled items with sorting of usable and scraped material at site.
Checking all the measurements recorded in the bill prepared by contractor at site with
respect to approved drawings and to certify the accuracy.
If bills / measurements not submitted by the contractor, the PMC shall take measurements
details of Civil and Electrical work jointly with contractor’s representative, record them in
computerized measurement books (MB) and obtain contractor’s signature in token of
acceptance & prepare bills.
On completion of work, the PMC shall have the responsibility to finalize the final bills for the
work as per actual execution and issue Completion Certificate to the Contractor.
In case Consultant finds discrepancies / defects and they are of minor nature, he may
issue Completion certificate along with the Snag list and also ensure that the Contractor
gives an undertaking that the Snags shall be attended and rectified within three (3) months
from the date of completion certificate.
Attending all the meetings related to the project, maintaining documentation of all project
related matters including minutes of different meetings.
For this the consultant shall be required to deploy a team at site of expert professionals as per
requirement for Civil, Electrical and HVAC work with required computers, printers and all the
necessary stationery. The details of the team required are in Section 7.1
After the project is implemented and completion certificate is given to the contractor, consultant
shall remain responsible for trouble shooting for the period of 1 year after which consultant’s
Performance security shall be refunded.
4.3 PAYMENT AND MILESTONES
Payment shall be made in following manner:
10% of the amount quoted in Financial Proposal on completion of 20% of work
15% of the amount quoted in Financial Proposal on completion of 40% of work
30% of the amount quoted in Financial Proposal on completion of 60% of work
30% of the amount quoted in Financial Proposal on completion of 80% of work
15% of the amount quoted in Financial Proposal on completion of 100% of work
4.4 THE AGREEMENT OF THE PROJECT
By submitting the proposal, the Bidder is deemed to have accepted all the terms and conditions of
the RFP.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
13
The Successful Bidder shall provide the performance security of 5% value in Rupees of accepted
commercial proposal in the form of a FDR / bank guarantee (irrevocable) drawn towards
“Commissioner, Pimpri Chinchwad Municipal Corporation” within 30 (Thirty) days of acceptance of
offer in the form of Letter of Award (LoA) simultaneously before Signing of Agreement. The FDR /
bank guarantee should be issued by a nationalised or scheduled bank and should be payable at
Pimpri. The Bank Guarantee is required to be maintained with the Corporation as performance
guarantee till completion of the period of Agreement or termination of the Agreement.
The Bid Security of the Successful Bidder (provided at the time of Bid submission) will be returned
to the bidder and will not form a part of performance security.
4.5 CONSULTANT‟S FAILURE TO CARRY OUT INSTRUCTIONS
In case of default on the part of the Consultant in carrying out such instruction within a reasonable
time, the Corporation shall be entitled to employ and pay other persons to carry out the same and if
such work is work which, in the opinion of the Corporation, the Consultant was liable to do at his
own cost under the Contract, then all costs consequent thereon or incidental thereto shall, after due
consultation with the Consultant , be determined by the Corporation and shall be recoverable from
the Consultant
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
14
5 DESCRIPTION OF THE SELECTION PROCESS
5.1 SELECTION PROCESS
The bidders shall make a hardcopy submission of bids in sealed envelopes, as per the format
defined in the RFP. The Bids shall comprise of:
Cover 1: Technical and financial capability
Cover 2: Financial Proposal
The Bidders shall be required to make submission, on or before the last date of submission.
The Bids received would be subject to a prima-facie check for Responsiveness followed by a step-
wise evaluation procedure as described below.
5.2 STEP 1 RESPONSIVENESS OF BID
The Bids submitted by Bidders shall be initially scrutinised to establish “Responsiveness”. A Bid
may be deemed “Non-Responsive” if it does not satisfy any of the following conditions:
a. Payment of Rs. 3,000/- (Rupees Three thousand only) against purchase of RFP document.
b. Payment of Rs. 27,700/- (Rupees Twenty Seven Thousand Seven Hundred only) as Bid
Security
c. It is not received by the due time and date as specified;
d. It does not contain sufficient information for it to be evaluated and/or is not in the formats
specified
e. It is not duly signed/scan sign/digitally signed and /or sealed in the manner prescribed and
to the extent indicated in Section 6.3.1 of this RFP Document;
The Bid shall be considered to be substantially responsive if it conforms to the preceding
requirements without material deviation or reservation. A material deviation or reservation is one
which,
a. Affects in any substantial way, the scope, quality, or performance of the Project, or
b. Limits in any substantial way, or is inconsistent with the RFP Document or Corporation’s
rights or the Bidder's obligations under this Agreement, or
c. Unfairly affects the competitive position of other Bidders presenting substantially
responsive bids.
d. The Bid to be submitted by the Bidders would have to be unconditional and unqualified and
the Bidders would be deemed to have accepted the terms and conditions of the RFP with
all its contents.
A bid once declared as “Non-Responsive” and rejected, cannot be made Responsive by the Bidder
having corrected or withdrawn the non-conforming deviation or reservation.
5.3 STEP 2 (COVER 1) EVALUATION OF TECHNICAL AND FINANCIAL CAPABILITY
In this stage the technical and financial capability of the Bidder in undertaking the Project would be
assessed. The Bidders would be evaluated on parameters as defined in Section 7 (Technical
Capacity Evaluation) and the Bidders found to be technically qualified would be eligible for the next
stage of the selection process.
During the evaluation of bids, the corporation may at its discretion, ask the bidders for clarifications.
Such clarification /s shall have to be provided within the time specified by Corporation. If the bidder
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
15
does not provide clarifications sought as mentioned above within the specified time period, the bid
is liable to be rejected.
5.4 STEP 3 EVALUATION OF FINANCIAL PROPOSAL
Evaluation of the financial proposals would be undertaken as detailed in Section 8. A ranked list (in
the ascending order of the lumpsum fee quoted viz, L1, L2…..Ln) by Bidders shall be prepared.
The bid security of top three ranked Bidders shall be retained till the signing of the Final Agreement
with the Successful Bidder.
Subsequent to this process, the Letter of Award (LoA) would be issued to the Successful Bidder by
Corporation. Within 7 (seven) days from the date of issue of the LoA, the Successful Bidder shall
send an acknowledgement agreeing to comply with the conditions set out therein and for the
execution of the Agreement. Corporation will promptly notify other Bidders that their Proposals
have been unsuccessful and their Bid Security will be returned within 30 days without interest on
the signing of the Operation and Maintenance Agreement with the Successful Bidder. The
Successful Bidder shall have to enter into an Agreement within 5 (five) days from date of issue of
the LoA. The Successful Bidder on the date of signing of the Agreement shall:
a. Furnish Performance Security of 5% value in Rupees of accepted commercial proposal in
the form of irrevocable Bank Guarantee / FDR issued by a nationalised/ scheduled bank in
favour of “The Commissioner, Pimpri Chinchwad Municipal Corporation”, as required under
the Agreement.
b. Shall pay the required Stamp Duty for the agreement.
Failure of the Successful Bidder to comply with the requirements mentioned in the above
paragraph shall constitute sufficient grounds for the annulment of the LoA, and forfeiture of the Bid
Security. In such an event, Corporation reserves the right to
a. either invite the next best Bidder for negotiations OR
b. call for fresh Bids OR
c. take any such measure as may be deemed fit in the sole discretion of Corporation,
including annulment of the bidding process.
5.5 GENERAL COMPLIANCE CRITERIA
1. The Bidder shall also submit with the proposal an undertaking in the requisite format
specified in Section 12 on an Indian non-judicial stamp paper of Rs. 100. This undertaking
is an affirmation from the Bidder with respect to the authenticity of information/ Documents
furnished along with the Proposal. Any deviation in material facts in respect to information/
Documents furnished by the Bidder in this respect is noted at any point of time (i.e. at the
time of submission or after signing the Agreement) then the bid can be disqualified or will
make the Successful Bidder liable for breach of contract in case the discrepancy is noted
after the signing of Agreement.
2. The Bidder shall submit a Power of Attorney as per the format enclosed in Section 11,
authorizing the signatory of the Proposals to commit the Bidder.
5.6 IMPORTANT DATES
Bid proceedings Time and Dates
Last date for receiving queries Upto 3.00 pm on 27/4/2018.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
16
Pre-bid Meeting 11.00 am on 26/4/2018.
Last date of receipt of Bid Upto 3.00 pm on 07/5/2018.
Time and date of opening of technical Bid 07/5/2018
Time and date of opening of financial Bid 09/5/2018.
In order to meet the above target dates, Bidders are expected to respond expeditiously to
clarifications, if any, requested during the evaluation process. Corporation shall adhere to the
above schedule to the extent possible. Corporation, however, reserves the right to modify the same
and the intimation to this effect shall be given to all the Bidders.
The Corporation also reserves the right to accept or reject, any or all of the bids without assigning
any reason.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
17
6 PROCEDURES TO BE FOLLOWED
6.1 ENQUIRIES & CLARIFICATIONS
Enquiries, if any, can be addressed to:
To
Joint City Engineer (E/M) First Floor
PCMC Main building
Pimpri, Pune-411 018, Maharashtra
It may kindly be noted that all the Clarifications should be mailed to [email protected]
and the same may kindly confirmed by making call to 020-67331421. Copy of the same may be
couriered to the above address. A format for requesting clarifications is provided at the back of
RFP.
The Bidders may contact Mr.S.Y.Khabde (Executive Engineer, Electrical Department), 1st floor,
PCMC main building, Pimpri-18 in case of any clarification.
Data to the extent available has been indicated in the RFP Document and the Bidders are
suggested to make their own investigations and collect additional data for preparation of the
Proposal. The Bidders can also procure the architectural drawings and schedules of the project
from the Corporation, by requesting in writing.
Corporation will endeavour to hold the pre-bid meeting as per the time schedule. Attendance of the
Bidders at the pre-bid meeting is not mandatory. However, subsequent to the meeting, Corporation
may not respond to queries from any Bidder.
All queries to be addressed at the pre-bid conference shall have to be submitted before the last
date for request of clarifications mentioned in Section 5.6.
Corporation shall aggregate all such clarifications, without specifying the source of clarifications,
and shall prepare a response, which shall be distributed to all parties who have procured the RFP
Document. It may be noted that queries in writing would be entertained only from those parties who
have been provided this RFP Document.
6.2 AMENDMENTS TO THE RFP
At any time prior to the last date for receipt of Bid as indicated in the RFP time schedule,
Corporation may, for any reason, whether at its own initiative or in response to clarifications
requested by a Bidder, amend the RFP by the issuance of addenda.
Any addendum thus issued would be in writing and sent to all the Bidders who have received and
acknowledged the RFP Document and shall be binding upon all the bidders. Bidders shall promptly
acknowledge receipt thereof to Corporation.
In order to afford Bidders reasonable time to take the addendum into account, or for any other
reason, Corporation may, at its discretion, change the last date for receipt of Bid.
6.3 SUBMISSION OF THE BID
6.3.1 Technical and financial capability
The Bidder shall be required to make a hardcopy submission of sealed proposals, on or before the
last date of submission. PCMC (or its consultants and/or advisors) will check Bids determined to be
substantially responsive for any arithmetic errors. Wherever there is discrepancy between the
amounts in figures and in words, the amount in words will govern. Any such corrections made by
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
18
PCMC shall be considered as binding upon the Bidder and will be duly notified to the Bidder in
writing. If the Bidder does not accept the corrections in Bid, PCMC may reject the Proposal and
forfeit the Bid Security
Cover 1 - Technical and financial capability
Submitted by: _________________________ (name of Bidder)
This submission shall have the following Documents which shall form part of the section entitled as
“Technical and Financial capability”:
a. Covering Letter as per Section 9
b. Description of the Bidder as per Section 10
c. Power of Attorney for the authorised representative as per Section 11
d. Undertaking as per Section 12
e. Information format for technical and financial capability as per Section 13 and Section 14
respectively (also attach the supporting Documents as matter of proof)
f. Attested copy of PAN Card
g. Attested copy of GST registration
h. Copy of the RFP, with each and every page signed by the Authorised representative as
designated under Section 11, with the seal of the bidder’s company on each page
i. The Document should be signed/scan signed by the authorised representative as designated
under Section 11 with the seal of the Bidder’s company.
The hardcopy of bid can be submitted by placing it in a sealed outer envelope, with the following
inscription:
To,
Joint City Engineer (E/M) First Floor
PCMC Main building
Pimpri, Pune-411 018, Maharashtra
“Proposal for the Selection of Project Management Consultancy (PMC) for Renovation of
Ramkrishna More Auditorium, Chinchwad”
“Submitted by: Name, Address and Contact Phone Number(s) of the Bidder”
If the envelope is not sealed and marked as instructed above, the Bid may be deemed to be Non-
Responsive and liable for rejection. Corporation assumes no responsibility for the misplacement or
premature opening of the Proposal submitted if the same is not in accordance with the prescribed
format. No document containing the financial proposal details shall be submitted with the hard copy
of technical proposal
The Bidder should take due care to submit the Bid before the due date and time as communicated
in the pre-bid meeting as stipulated in Section 5.6 of the RFP Document. Corporation shall not be
responsible for any delay in submission of the Bids. Any Bid received by Corporation after the
deadline for submission of the Bids stipulated in Section 5.6 shall not be opened.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
19
6.3.2 Financial Proposal
The Bidder shall fill in the online format of Financial Proposal to be accepted for evaluation. The
Financial Proposal in the online format shall be as in the format in Section 15, to be considered for
evaluation.
6.3.3 Bidder registration process
Not required.
6.4 INITIALLING OF THE BIDS
Each page of the Bid should be initialled by the authorised representative (as defined in Section
6.5), of the Bidder.
6.5 INSTRUCTIONS TO BIDDERS
All Bidders should note the following:
1. No bidder shall submit more than one bid for the project.
2. Bids that are incomplete in any respect or those that are not consistent with the requirements
as specified in this RFP or those that do not contain the covering Letter as per the specified
formats may be considered Non-Responsive and may be liable for rejection.
3. Strict adherence to formats, wherever specified, is required. Non-adherence to formats may
be a ground for declaring the Bid Non-Responsive.
4. Bidders may note that Corporation will not entertain any deviations to the RFP at the time of
submission of the Bid or thereafter. The Bid to be submitted by the Bidders would have to be
unconditional and unqualified and the Bidders would be deemed to have accepted the terms
and conditions of the RFP with all its contents. Any conditional Bid shall be regarded as Non-
Responsive and would be liable for rejection.
5. The Bid and all related correspondence and Documents shall be written in the English
language only. Supporting Documents and printed literature furnished by the Bidder along
with the Bid may be in any other language, provided that they are accompanied by an
appropriate translation into English. Supporting materials that are not translated into English
will not be considered. For the purpose of interpretation and evaluation of the Proposal, the
English language translation shall prevail. All communication and information provided
should be legible, and wherever the information is given in figures, the same should also be
mentioned in words.
6. No change in, or supplementary information to a Bid shall be accepted once submitted.
However, Corporation reserves the right to seek additional information from the Bidders if
found necessary, during the course of evaluation of the Bid. Non-submission, incomplete
submission or delayed submission of such additional information or clarifications sought by
Corporation, may be a ground for rejecting the Bid.
7. The currency for the purpose of the Bid shall be the Indian Rupee (INR).
8. The Bids shall be evaluated as per the criteria specified in this RFP Document. However,
within the broad framework of the evaluation parameters as stated in the Request for
Proposal, Corporation reserves the right to make modifications to the stated evaluation
criteria, which would be uniformly applied to all the Bidders.
9. The Bidder should designate one person (Authorised Representative) authorised to
represent the Bidder in its dealings with Corporation. This designated person should hold the
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
20
Power of Attorney and be authorised to perform all tasks including but not limited to providing
information, responding to enquiries, entering into contractual commitments on behalf of the
Bidder etc. The covering letter submitted by the Bidder shall be signed by the authorised
Signatory and shall bear the stamp of the entity thereof.
10. Corporation reserves the right to reject any or all of the Bids without assigning any reason
whatsoever.
11. Corporation reserves the right to invite revised Proposals from Bidders with or without
amendment of the RFP at any stage, without liability or any obligation for such invitation and
without assigning any reason.
12. Mere submission of information does not entitle the Bidder to meet an eligibility criterion.
Corporation reserves the right to vet and verify any or all information submitted by the Bidder.
If any claim made or information provided by the Bidder in the Bid or any information
provided by the Bidder in response to any subsequent query by Corporation, is found to be
incorrect or is a material misrepresentation of facts, then the Bid will be liable for rejection.
Mere clerical errors or bonafide mistakes may be treated as an exception at the sole
discretion of Corporation and if Corporation is adequately satisfied.
13. The Bidder shall be responsible for all the costs associated with the preparation of the Bid.
Corporation shall not be responsible in any way for such costs, regardless of the conduct or
outcome of this process.
14. The Bidder would be granted permission by Corporation for visit of the Project Site on receipt
of a formal written request, reasonably in advance of the proposed date of visit.
6.6 BIDDER‟S RESPONSIBILITY
The Bidder is expected to examine carefully the contents of all the Documents provided. Failure to
comply with the requirements of RFP shall be at the Bidder's own risk. It shall be deemed that prior
to the submission of Proposals, the Bidder has:
1. Made a complete and careful examination of terms & conditions/ requirements, and other
information set forth in this RFP Document
2. Received all such relevant information as it has requested from Corporation; and
3. Made a complete and careful examination of the various aspects of the Project including but
not limited to:
a. Bidders own validation of the project Site, location and other existing facilities and
infrastructure
b. Any clearances obtained by Corporation for the Project; and
c. All other matters that might affect the Bidder’s performance under the terms of this
RFP Document.
4. Corporation shall not be liable for any mistake or error or neglect by the Bidder in respect of
the above.
6.7 VALIDITY OF TERMS OF THE BID
Each Bid shall indicate that it is a firm and irrevocable offer, and shall remain valid and open for a
period of not less than 180 days from the last date for submission of the Bid. Non-adherence to this
requirement will be a ground for declaring the Bid as Non-Responsive. However, Corporation may
solicit the Bidder’s consent for extension of the period of validity. Such request for extension shall
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
21
be made by Corporation in writing. The Bidder agrees to reasonably consider such a request and
shall send its response in writing. A Bidder accepting Corporation request for extension of validity
shall not be permitted to modify his Bid in any other respect.
6.8 FEES AND DEPOSITS TO BE PAID BY THE BIDDERS
6.8.1 Bid Security
Bidders are required to submit a Bid Security for an amount equal to Rs. 27,700/- (Rupees Twenty
Seven Thousand Seven Hundred only) through the e-tendering system of PCMC.
Bids of Bidder(s), who fail to furnish the above Bid Security, shall be liable for rejection by
Corporation as Non-Responsive.
Subject to the other clauses of this Section 6.8.1, Corporation shall reserve the right to forfeit the
Bid Security under the following circumstances:
a. If the Bidder withdraws his Bid at any time during the stipulated period of Bid validity
as per Section 6.7 (or as may be extended).
b. If the Bidder, for the period of Bid validity:
i. In Corporation’s opinion, commits a material breach of any of the terms and /
or conditions contained in the RFP Document and / or subsequent
communication from Corporation in this regard.
ii. Refuses to accept the Letter of Award.
In the event that any Bidder is not found to be technically qualified, then the Bid Security in such
cases, shall be returned to the respective Bidder within 30 (thirty) days from such cessation without
interest.
The Bid Security of the unsuccessful Bidders (after opening the Financial Proposal) will be returned
after 30 (thirty) days without any interest, following the signing of the Agreement by the Successful
Bidder.
The Bid Security of the Successful Bidder shall be required to be maintained till the signing of the
Agreement.
6.9 NON ASSOCIATION WITH PROJECT ADVISORS
Corporation has retained project advisors for assistance in the selection process. The Bidders are
required not to have any association with the members, or attempt to exercise undue influence on
the members, of the project advisory team or to influence from the date of receipt of this Document
till the completion of the selection process. Non-conformance with this requirement is a sufficient
condition for the disqualification of any Bidder from the selection process.
6.10 CONSEQUENCES OF NOT ADHERING TO THE PROCESS
The consequences of not adhering to the specific procedures laid herein above will lead to rejection
of the Proposal.
6.11 RIGHT TO REJECT THE PROPOSAL
Corporation is not bound to accept any of the Proposals submitted. Corporation reserves the right
to reject any or all of the Bids submitted in response to this Request for Proposal at any stage
without assigning any reasons whatsoever. Any Bidder shall have no cause of action or claim
against Corporation or its officers, employees, successors or assignees for rejection of their Bid.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
22
7 TECHNICAL CAPABILITY EVALUATION
Qualification will be based on the assessment of the technical and financial capability of the
Bidders in operating and maintaining the Project facilities. The Bidders would be evaluated on
eligibility criteria as defined in Section 7.1. & 7.2. The Bidders found to be technically and financially
capable (i.e. fulfil both the technical and financial eligibility criteria) would be eligible for the next
stage of the Selection Process.
7.1 MINIMUM ELIGIBILITY CRITERIA: TECHNICAL CAPABILITY
The Bidder shall satisfy the following criteria to qualify for the Project.
1) Should be a Company / Firm been in existence for minimum 7 (seven) years immediately
preceding the bid due date.
2) Should have rendered any three of the following PMC services for at least one project of
auditorium comprising of Civil, Electrical, HVAC, Acoustical, Advanced sound system and
installing solar power panels, for Government / Semi-Government/ Private clients
3) Should have rendered PMC services for at least one project in the last seven years
immediately preceding the bid due date, costing not less than Rs. 5 Crore.
4) The bidder shall also have to deploy at site, full-time qualified experts throughout the
execution of work team. The team should comprise of:
I. One Resident Engineer: One full time Civil Engineering Degree holder having minimum
5 years’ experience
II. One Junior Engineer: Civil Diploma holder with minimum 3 years’ experience
III. Electrical / HVAC Engineer: Electrical Engineer / Electrical Diploma holder with
minimum 3 years’ experience
The above requirement is considered minimum. However, more Engineers and other categories of
support staff may have to be appointed by the bidder, if necessary for satisfactory supervision. The
bidder shall also have to mandatorily have at some stage, the following expert with the site team:
IV. One Acoustics’ expert: Diploma holder in Building Acoustics with sufficient experience.
V. One Solar Engineer: Graduate in Solar engineering with sufficient experience
The Bidder should furnish evidence of education qualification and experience (from relevant
authority/ organisation) to support its claim as per Section 13.
It is specifically agreed that PCMC shall have no responsibility for any Staff / Engineers engaged by
the bidder and the said bidder alone shall be responsible.
7.2 MINIMUM ELIGIBILITY CRITERIA: FINANCIAL CAPABILITY
To qualify the Bidder shall have an average annual turnover of at least Rs. 10 Lakh (Rupees ten
lakh) or more in the last three financial years, immediately preceding the bid due date.
The Bidders should provide information regarding the above based on audited annual accounts for
the respective financial years. The financial year would be the same as the one normally followed
by the Bidder for its annual financial statement.
The Bidder should furnish the details to support its claim as per Section 14.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
23
7.3 EVALUATION PROCESS
A Bidder qualifying on all of the technical capability criteria and financial capability criteria would be
considered technically and financially capable. Only those Bidders who are found to be technical
financially capable would be considered for further evaluation.
7.4 TECHNICAL AND FINANCIAL CAPABILITY INFORMATION FORMATS
The information format for submission of the technical capability information is detailed in Section
13 and Section 14 respectively. The Bidder is required to submit completion certificates/
agreements/ work orders along with any other supporting documents as proof for the technical
eligibility criteria. The above mentioned documents must be provided for the entity eligible to be
evaluated under the technical capability.
The Bid must be accompanied by the audited annual financial statements of the entity to be
evaluated for financial capability for the last three financial years. In case the annual accounts for
the latest financial year are not audited and therefore the Bidder could not make it available, the
Bidder shall give an undertaking to that effect and the statutory auditor shall certify the same. In
such a case, the Bidder may provide the audited annual accounts (with schedules) for the previous
financial year. In any case, the audited annual financial statements for three years preceding the
latest financial year would have to be provided, failing which the Proposal will be rejected as non-
responsive.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
24
8 FINANCIAL PROPOSAL EVALUATION
Only proposal which are technically qualified as per Section 7 will be considered for Financial
evaluation. The Financial Proposal evaluation seeks to select the entity offering the best
commercial terms.
8.1 FINANCIAL PROPOSAL PARAMETERS
The bidding parameter shall be the fee quoted by the Bidder to fulfil the scope highlighted in
Section 4.2. The Financial Proposal of the Bidder will be evaluated as per the quote submitted.
The Bidder in the Financial Proposal shall quote a lumpsum amount (as fee) in Rupees as
indicated in Financial Proposal format. The fee quoted by the bidder shall not be conditional and
any alteration will not be considered at the signing of Agreement. The quote shall be inclusive of all
expenses, prevailing taxes and duties including Goods & Service Tax (GST) at the given point of
time of bid.
8.2 EVALUATION OF FINANCIAL PROPOSAL
The Financial Proposals would be ranked in the ascending order of the quotes viz, L1, L2…..Ln;
with the Bidder quoting the lowest quote ranked first, the Bidder quoting the second lowest quote
shall be ranked as second and so on. The bidder whose rate of financial proposal is lowest will be
declared as Successful Bidder.
Bidders are requested to note that the Financial Proposal should not have any conditionality
attached or deviations from the RFP. Bids with conditions attached may be treated as Non-
Responsive and liable for rejection at the discretion of Corporation.
In the event that two or more Bidders quote the same amount in the Financial Proposal, the
Corporation may invite fresh Financial Proposals from such Bidders only. This process shall be
repeated for three times if similar situation arises. However, even after taking such repeated steps,
the situation remains unchanged then the bid selection would be settled through drawing of lots
among the tied bidders.
PCMC shall not be held responsible for any errors or mistakes arising out of the bidding.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
25
9 FORMAT OF THE COVERING LETTER
(The covering letter is to be submitted on the Company’s letterhead)
Date:
Place:
To
The Commissioner, Pimpri Chinchwad Municipal Corporation, Pimpri Chinchwad Municipal Corporation Main Building, Pimpri – 411 018 Maharashtra
Sub: “Selection of Project Management Consultancy (PMC) for Renovation of Ramkrishna More Auditorium, Chinchwad”
Dear Sir,
Please find enclosed our Proposal in respect of project mentioned in subject, in response to the Request for Proposal (“RFP”) Document issued by the Corporation dated 19
th April, 2018.
We hereby confirm the following:
1. The Proposal is being submitted by (name of the Bidding Company) who is the Bidding Company, in accordance with the conditions stipulated in the RFP.
2. We have examined in detail and have understood the terms and conditions stipulated in the RFP Document issued by Corporation and in any subsequent communication sent by Corporation. We agree and undertake to abide by all these terms and conditions. Our Proposal is consistent with all the requirements of submission as stated in the RFP or in any of the subsequent communications from Corporation.
3. The information submitted in our Proposal is complete, is strictly as per the requirements as stipulated in the RFP, and is correct to the best of our knowledge and understanding. We would be solely responsible for any errors or omissions in our Proposal.
4. We confirm that our Financial Proposal does not contain any conditions.
5. The Bidding Company satisfies the legal requirements and meets all the eligibility criteria laid down in the RFP.
6. A Power of Attorney from the Bidding Company authorising the undersigned as the Authorised Representative who is authorised to perform all tasks including, but not limited to providing information, responding to enquiries, entering into contractual commitments on behalf of the Bidder, etc., in respect of the Project is included as a part of the Proposal.
7. We confirm that our Bid is valid for a period of 180 days from the last date of submission of the Bid. We understand that PCMC may also require us to extend the validity of the bid for such period as may be determined by PCMC at its discretion.
For and on behalf of :
Signature :
(Authorised Representative and Signatory)
Name of the Person : Designation : Enclosures: Power of Attorney
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
26
10 DESCRIPTION OF THE BIDDER
Details of Bidder:
Particulars Details Instructions
Name of the Bidding Company / Partnership
Firm/ Proprietary Firm
Copy of Incorporation Certificate /
Registration certificate to be
attached
Address of the Registered/ Head Office
Contact person and contact details
At least 7 years in existence Copy of Incorporation Certificate /
Registration certificate to be
attached
Average annual turnover in last three
financial years immediately preceding the bid
due date
Year 1
Year 2
Year 3
Auditor certificate / CA certificate to
be attached along with the audited
annual financial statements for the
last three years ending on 31st
March 2018.
Should have rendered any three of the
following services related to construction
Management & Supervision for Civil,
Electrical, HVAC ,Acoustical, Advanced
sound system works of any one project of
auditorium for Government/ Semi-
Government/ Private clients
Client certificate / work order
The Bidder should have rendered PMC
services for at least one project in the last
seven years immediately preceding the bid
due date, costing not less than Rs. 5 Crore.
Client certificate indicating
performance / work order
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
27
11 FORMAT OF POWER OF ATTORNEY FOR AUTHORISED REPRESENTATIVE
(On the Stamp Paper of min. Rs. 100 as per the Stamp paper Act prevailing in the State of Maharashtra)
Power of Attorney
Know all men by these presents, We…………………….(name and address of the registered office)
do hereby constitute, appoint and authorise Mr / Ms………………………………(name and
residential address) who is presently employed with us and holding the position of
………………………. as our attorney, to do in our name and on our behalf, all such acts, deeds and
things necessary in connection with or incidental to our proposal for the project of „Selection of
Project Management Consultancy (PMC) for Renovation of Ramkrishna More Auditorium,
Chinchwad”, including signing and submission of all Documents and providing information /
responses to Pimpri Chinchwad Municipal Corporation ("PCMC"), representing us in all matters
before PCMC, and generally dealing with PCMC in all matters in connection with our Proposal for
the said Project.
We hereby agree to ratify all acts, deeds and things lawfully done by our said attorney pursuant to
this Power of Attorney and that all acts, deeds and things done by our aforesaid attorney shall and
shall always be deemed to have been done by us.
For ___________________________ (Signature)
(Name, Title and Address)
Accepted
………….. (Signature)
(Name, Title and Address of the Attorney)
Note:
In case of Bidders who are not resident in India, the Power of Attorney may be submitted on plain paper
attested by any authorised officer of the Embassy of India and duly stamped by the Registration
Department of the Government of Maharashtra.
The mode of execution of the Power of Attorney should be in accordance with the procedure, if any, laid
down by the applicable law and the charter Documents of the executant (s) and when it is so required the
same should be under common seal affixed in accordance with the required procedure.
Also, wherever required, the Bidder should submit for verification the extract of the charter Documents
and Documents such as a resolution/ power of attorney in favour of the Person executing this Power of
Attorney for the delegation of power hereunder on behalf of the Bidder.
In case an authorised Director of the Bidder signs the Proposal, a certified copy of the appropriate
resolution conveying such authority may be enclosed in lieu of the Power of Attorney.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
28
12 FORMAT FOR UNDERTAKING
(To be executed on a Non-judicial Rs. 100 Stamp Paper as per the Stamp paper Act prevailing in the State of Maharashtra)
The information/ Documents submitted by us are true to our knowledge and if the information/
Documents so furnished shall be found to be untrue or false, the Bid shall be liable to be
disqualified and our Bid security accompanying the Bid will be forfeited.
Also we are aware that if the information/ Document furnished is found to be untrue or false during
the currency of contract, then our contract is liable to be terminated.
We hereby declare that we have made ourselves thoroughly conversant with the specifications,
conditions laid by Pimpri Chinchwad Municipal Corporation (“PCMC”) for this Bid and we have
understood the same before submitting this Bid.
We hereby certify and confirm that in the preparation and submission of our Bid for the proposals
listed below, we have not acted in concert or in collusion with any other Bidder or other person(s)
and also not done any act, deed or thing which is or could be regarded as anti-competitive.
We further confirm that we have not offered nor will offer any illegal gratification in cash or in kind to
any person or agency in connection with the instant proposals.
We agree that the amount of Bid Security shall be liable to be forfeited by PCMC, should we fail to
abide by the stipulation to keep the offer open for a period of not less than 180 days from the date
fixed for opening the same and thereafter until it is withdrawn by us by the notice in writing duly
addressed to the authority opening the Bid.
Bidder _______________________
Address ________________________
________________________
Dated the ________ day of ______________ 2018 Signature of Bidder
Witness
Address ________________________
________________________
Dated ____ day of ________ 2018 Signature of Witness
13 INFORMATION FORMAT FOR TECHNICAL CAPABILITY
Experience of the Bidder and Supporting Documents
Qualification Criteria Supporting Documents
Should have rendered any three of the following
services related to construction Management &
Client certificate / work order
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
29
Supervision for Civil, Electrical, HVAC ,Acoustical,
Advanced sound system works of any one project of
auditorium for Government/ Semi-Government / Private
clients
The Bidder should have rendered PMC services for at
least one project in the last seven years immediately
preceding the bid due date, costing not less than Rs. 5
Crores.
Client certificate indicating performance /
work order
Experience of the proposed team at site and Supporting Documents
Qualification Criteria Supporting Documents
I. One Resident Engineer: One full time Civil
Engineering Degree holder having minimum 5 years’
experience
II. One Junior Engineer: Civil Diploma holder with
minimum 3 years’ experience
III. Electrical / HVAC Engineer: Electrical Engineering
Degree / Electrical Diploma holder with minimum 3
years’ experience
The bidder shall also need to have at some stage, the following:
IV. One Acoustics’ expert: Diploma holder in Building
Acoustics with sufficient experience
V. One Solar Engineer: Graduate in Solar engineering
with sufficient experience
Relevant certified copies of
education and work experience
Also mention name, designation,
address and telephone number
of the contact officer from whom
the details can be verified
Supporting Documents
The Bidder should provide details of only those projects undertaken by it under its own name. Project
experience of the Bidder’s parent company or its subsidiary or any associate company will not be considered
for computation of the experience. The independent auditor issuing the certificate should clearly indicate his /
her membership assigned by the Institute of Chartered Accountants of India (ICAI) or equivalent organisation
abroad.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
30
14 INFORMATION FORMAT FOR FINANCIAL CAPABILITY
S. No. Financial Year Annual Turnover
(Rs.in crores)
1. 2016-17
2. 2015-16
3. 2014-15
Certificate from the Statutory Auditor
This is to certify that …………………………… (Name of the Applicant) has received the payments shown above against the respective years on account of professional fees.
Name of the audit firm:
Seal of the audit firm
Date:
(Signature, name and designation of the authorised signatory)
These above figures have to be certified by the Statutory Auditor. The independent auditor issuing
the certificate should clearly indicate his/her membership number assigned by the Institute of
Chartered Accountants of India (ICAI) or equivalent organisation abroad.
Along with the format the Bidder needs to submit audited annual financial statements for the last
three years ending on 31st March 2017.
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
31
15 FINANCIAL PROPOSAL FORMAT
Date: Place:
To
The Commissioner,
Pimpri Chinchwad Municipal Corporation,
Pimpri Chinchwad Municipal Corporation Main Building,
Pimpri – 411 018
Maharashtra
Dear Sir,
Sub: “Selection of Project Management Consultancy (PMC) for Renovation of Ramkrishna More Auditorium, Chinchwad”
Please find enclosed our Financial Proposal in respect of the project of Selection of Project
Management Consultancy for Renovation of Ramkrishna More Auditorium, in response to the
Request for Proposal (“RFP”) Document issued by the Corporation dated ____________ 2018.
Description Lump sum Professional fee for the Scope of work defined in RFP (In figures )
Professional fees for the professional services to be rendered for Civil, Electrical, A/C, Mechanical, Acoustics and other allied works, for the project as stipulated in the RFP document
Rs. -----
The quote shall be inclusive of all the expenses, prevailing duties and taxes including Goods & Service Tax (GST) at the given point of time of bid.
Thanking you,
Yours sincerely,
For and on behalf of : (here enter the name of the Bidder and the Company Seal)
Signature : (Authorised Representative and Signatory)
Name of the Person :
Designation :
Note:
1. The above quote is inclusive of all applicable taxes and duties including Goods & Service
tax at the time of bid submission. Any change in the GST or change in structure of taxes
at a later stage or incorporation of any new tax or duty at a later stage will be reimbursed
to the bidder at actual as applicable.
2. All other expenditure required for undertaking the project shall be borne by the bidder
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
32
16 FORMAT FOR SEEKING CLARIFICATIONS
Clause number in the
RFP document
Page number in the
RFP document
Clarification/Change
needed on the
Clause
Reason/Remarks
Selection of PMC for Renovation of Ramkrishna More Auditorium, Chinchwad
33
17 DESIGN, SPECIFICATION & BOQ FOR THE RENOVATION WORK
(Enclosed Volume II & III of RFP No. _______)
Item
No.Qty Unit Discription Per Amount
In Figures In Words
1 762.57 Cum
Excavation for foundation in earth, soil of all types, sand, gravel
and soft murum, including removing the excavated material up to
a distance of 50 m. beyond the building area & stacking and
spreading as directed, dewatering, preparing the bed for the
foundation and necessary back filling, ramming, watering
including shoring and strutting etc. complete. (Lift upto 1.5 m.) By
Mechanical Means
117.60Rupees One hundred
Seventeen Paise Sixty OnlyCum 89,678.23
2 1,467.14 Cum
Excavation for foundation in earth, soil of all types, sand, gravel
and soft murum, including removing the excavated material up to
a distance of 50 m. beyond the building area & stacking and
spreading as directed, dewatering, preparing the bed for the
foundation and necessary back filling, ramming, watering
including shoring and strutting etc. complete. (Lift upto 1.5 m. to
3.0m) By Mechanical Means
122.85Rupees One hundred Twenty
Two Paise Eighty Five OnlyCum 1,80,238.09
PCMC - CIVIL WORK
Estimated Rates
Memorandum showing the items of work to be carried out
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION A :- CIVIL WORKS (PART A)
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B
3 724.61 Cum
Excavation for foundation in hard murum including removing the
excavated material upto distance of 50 metres beyond the
building area and stacking and spreading as directed, dewatering,
preparing the bed for the foundation and necessary back filling,
ramming, watering including shoring and strutting etc. complete.
(Lift upto 1.50 m to 3.0m) By Mechanical Means
137.55Rupees One hundred Thirty
Seven Paise Fifty Five OnlyCum 99,670.45
4 139.48 Cum
Excavation for foundation in Hard rock by chiselling, wedging,
line drilling, etc. including trimming and levelling the bed,
removing the excavated material upto a distance of 50 metres
beyond the building area stacking as directed, dewatering and
back filling with available earth/ murum watering, ramming etc.
complete. (Lift above 3.0m).
693.00Rupees Six hundred Ninety
Three OnlyCum 96,657.28
5 188.92 Cum
Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling
15 cm to 20 cm thick including hand packing and compacting etc.
complete.
627.51Rupees Six hundred Twenty
Seven Paise Fifty One OnlyCum 1,18,549.59
6 135.61 CumProviding and filling in the foundation with sand of approved
quality including watering, compacting etc. complete.1243.33
Rupees One Thousand Two
hundred Forty Three Paise
Thirty Three Only
Cum 1,68,604.27
7 240.00 Cum
Removing & transporting the excavated materials with all leads,
lifts, conveying & stacking, loading,unloading as directed within
P.C.M.C. limit. 3km
83.32Rupees Eighty Three Paise
Thirty Two OnlyCum 19,996.80
8 2.00 M.T.
Providing and fabricating structural steel work in rolled sections
like joists, channels, angles, tees etc. as per detailed design and
drawings or as directed including cutting, fabricating, hoisting,
erecting, fixing in position making riveted / bolted /welded
connections without connecting plates, braces etc. and including
one coat of anticorrosive paint and over it two coats of oil painting
of approved quality and shade etc. complete.
59220.00Rupees Fifty Nine Thousand
Two hundred Twenty OnlyM.T. 1,18,440.00
9 2.00 M.T.
Providing and fabricating structural steel work in rolled sections,
fixed with connecting plates or angle cleats in main and cross
beams, hip and jack rafters, purlins connecting to truss members
and the like, as per detailed designs and drawing or as directed
including cutting, fabricating, hoisting, erecting, fixing in position,
making riveted/ bolted/ welded connections and one coat of
anticorrosive paint and over it two coats of oil painting of approved
quality and shade etc. complete.
53340.00
Rupees Fifty Three
Thousand Three hundred
Forty Only
M.T. 1,06,680.00
10 3.00 M.T.
Providing, fabricating and erecting at site of work the tubular steel
structure (shed) as per standard design and specifications having
various spans in between trusses and in multiples of standard
length of bays as specified as per standard specifications,
inclusive of cost of steel tubular trusses, tubular columns purlins,
tie runners, foundation bolts, base plates, nuts and bolts, welding
wherever required etc. as per detailed drawing inclusive of one
coat of anticorrosive paint and two coats of oil painting of
approved quality and shade etc. complete. Spec. No. : As directed
by Engineerincharge.
77700.00
Rupees Seventy Seven
Thousand Seven hundred
Only
M.T. 2,33,100.00
11 85.12 Cum
Providing and laying in situ cement concrete M20 of trap / granite
/quartzite/ gneiss metal for R.C.C. work in foundations like raft,
strip foundations, grillage and footings of R.C.C. columns and
steel stanchions etc. including bailing out water, formwork, cover
blocks compaction and curing roughening the surface if special
finish is to be provided (Excluding reinforcement and structural
steel) etc. etc. complete, With fully automatic micro processor
based PLC without SCADA enabled reversible drum type
concrete mixer . With natural sand.
5562.29
Rupees Five Thousand Five
hundred Sixty Two Paise
Twenty Nine Only
Cum 4,73,466.96
12 235.75 Cum
Providing and laying in situ cement concrete M25 of trap / granite
/quartzite/ gneiss metal for R.C.C. work in foundations like raft,
strip foundations, grillage and footings of R.C.C. columns and
steel stanchions etc. including bailing out water, formwork ,cover
blocks compaction and curing roughening the surface if special
finish is to be provided (Excluding reinforcement and structural
steel) etc. etc. complete, With fully automatic micro processor
based PLC without SCADA enabled reversible drum type
concrete mixer.. With natural sand.
5744.99
Rupees Five Thousand
Seven hundred Forty Four
Paise Ninety Nine Only
Cum 13,54,381.39
13 125.05 Cum
Providing and laying in situ cement concrete M30 of trap / granite
/quartzite/ gneiss metal for R.C.C. work in foundations like raft,
strip foundations, grillage and footings of R.C.C. columns and
steel stanchions etc. including bailing out water, formwork, cover
blocks compaction and curing roughening the surface if special
finish is to be provided (Excluding reinforcement and structural
steel) etc. etc. complete, With fully automatic micro processor
based PLC without SCADA enabled reversible drum type
concrete mixer. With natural sand.
5778.59
Rupees Five Thousand
Seven hundred Seventy Eight
Paise Fifty Nine Only
Cum 7,22,635.07
14 89.26 Cum
Providing and casting in situ cement concrete M20 of trap /
granite /quartzite/ gneiss metal for R.C.C. columns as per detailed
designs and drawing or as directed including centering, formwork,
cover blocks compaction finishing the formed surfaces with
cement mortar 1:3 of sufficient minimum thickness to give a
smooth and even surface or roughening if special finish is to be
provided and curing etc. complete. (Excluding reinforcement and
structural steel).With fully automatic micro processor based PLC
without SCADA enabled reversible drum type concrete mixer With
Natural sand.
8088.59
Rupees Eight Thousand
Eighty Eight Paise Fifty Nine
Only
Cum 7,21,978.24
15 136.53 Cum
Providing and casting in situ cement concrete in M25 of trap/
granite/ quartzite/ gneiss metal for R.C.C. beams and lintels
as per detailed designs and drawings or as directed including
centering, formwork, cover blocks compaction and roughening the
surface if special finish is to be provided and curing etc. complete.
(Excluding reinforcement and structural steel).With fully automatic
micro processor based PLC without SCADA enabled reversible
drum type concrete mixer With natural sand
9023.09
Rupees Nine Thousand
Twenty Three Paise Nine
Only
Cum 12,31,918.15
16 163.05 Cum
Providing and casting in situ cement concrete M25 of trap/
granite / quartzite/ gneiss metal for R.C.C. slabs and landings
canopy as per detailed designs and drawings including centering,
formwork, cover blocks compaction finishing the formed surfaces
with cement mortar 1:3 of sufficient minimum thickness to give a
smooth and even surface or roughening if special finish is to be
provided and curing etc. complete, (Excluding reinforcement and
structural steel).With fully automatic micro processor based PLC
without SCADA enabled reversible drum type concrete mixer With
natural sand.
9663.59
Rupees Nine Thousand Six
hundred Sixty Three Paise
Fifty Nine Only
Cum 15,75,603.41
17 1.54 Cum
Providing & casting in situ cement concrete M25 of trap/
granite/ quartzite/ gneiss metal for R.C.C. chajja as per
detailed design & drawings including centering, formwork, cover
blocks compacting , curing , finishing & roughening the surface if
special finish is to be provided & curing complete. (Excluding
reinforcement and structural steel).With fully automatic micro
processor based PLC without SCADA enabled reversible drum
type concrete mixer With natural sand.
10041.59Rupees Ten Thousand Forty
One Paise Fifty Nine OnlyCum 15,454.01
18 0.33 Cum
Providing and casting in situ cement concrete in M25 of trap/
granite/ quartzite/ gneiss metal for R.C.C. pardi of required
thickness including centering, formwork, cover blockscompacting ,
curing , finishing & roughening them if special finish is to be
provided and curing complete. (Excluding reinforcement and
structural steel).With fully automatic micro processor based PLC
without SCADA enabled reversible drum type concrete mixer.With
natural sand.
10577.09
Rupees Ten Thousand Five
hundred Seventy Seven
Paise Nine Only
Cum 3,490.44
19 0.11 Cum
Providing and casting in situ cement concrete in M20 of trap/
granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or
parapet and sill of doors and windows moulded as per detailed
drawings or chamfered as approved by the Engineer including
centering, formwork, cover blocks compacting , curing , finishing &
roughening them if special finish is to be provided and curing
complete. (Excluding reinforcement and structural steel).with fully
automatic micro processor based PLC without SCADA enabled
concrete batch mix plant (pan mixer).... With natural sand.
6560.84
Rupees Six Thousand Five
hundred Sixty Paise Eighty
Four Only
Cum 746.95
20 1.75 Cum
Providing cast in situ M-10 grade cement concrete for head walls
of C.D. work/ retaining walls etc. including necessary form work,
compaction finishing and curing etc. complete. with reversible
Drum Type mixer without SCADA. (Cement 4.05 bags/cu.m.) With
natural sand.
Spec : CD 8 Page 163
4142.86
Rupees Four Thousand One
hundred Forty Two Paise
Eighty Six Only
Cum 7,250.01
21 54.44 mt
Providing and fixing in position TMT FE 500 bar reinforcement
of various diameters for R.C.C. pile caps, footings, foundations,
slabs, beams columns, canopies, staircase, newels, chajjas,
lintels pardis, copings, fins, arches etc. as per detailed designs,
drawings and schedules. Including cutting, bending, hooking the
bars, binding with wires or tack welding and supporting as
required complete. a) For TMT Fe 415 steel bars ( If Mild
Steel/HYSD steel is to be used prior permission from S.E. should
be taken )
53193.00
Rupees Fifty Three
Thousand One hundred
Ninety Three Only
M.T. 28,95,592.87
22 2.46 Cum
Providing second class Burnt Brick masonry with conventional/
I.S. type bricks in cement mortar 1:6 in foundations and plinth
of inner walls/ in plinth external walls including bailing out
water manually , striking joints on unexposed faces, raking out
joints on exposed faces and watering etc. Complete.
5422.83
Rupees Five Thousand Four
hundred Twenty Two Paise
Eighty Three Only
Cum 13,323.89
23 84.49 Cum
Providing second class Burnt Brick masonry with
conventional/ I.S. type bricks in cement mortar 1:6 in
superstructure including striking joints, raking out joints, watering
and scaffolding etc. Complete
5443.83
Rupees Five Thousand Four
hundred Forty Three Paise
Eighty Three Only
Cum 4,59,963.43
24 2.46 Sqm
Providing second class Burnt Brick masonry with
conventional/ I.S. type bricks in cement mortar 1:4 in half brick
thick wall including mild steel longitudinal reinforcement of 2 bars
of 6 mm diameter / 2 hoop iron strips 25 mm X 1.6 mm placed at
every third course, properly bent and bonded at ends scaffolding,
racking out joints and watering etc. complete.
719.17
Rupees Seven hundred
Nineteen Paise Seventeen
Only
Sqm 1,771.53
25 1.46 Cum
Providing uncoursed rubble masonry of trap / granite /
quartzite/ gneiss stones in cement mortar 1:6 in foundation
and plinth of inner walls / in plinth of external walls including
bailing out water manually , striking joints on un exposed faces
and watering etc.complete.
3496.54
Rupees Three Thousand
Four hundred Ninety Six
Paise Fifty Four Only
Cum 5,097.96
26 1.58 Cum
Providing coursed rubble masonry second sort of trap /
granite / quartzite / gneiss stones in cement mortar 1:6 in
superstructure including raking out joints when plastering is to be
done and striking joints when no plastering is to be done on the
inside, watering scaffolding etc.complete.
7539.04
Rupees Seven Thousand
Five hundred Thirty Nine
Paise Four Only
Cum 11,873.99
27 247.29 Sqm
Providing water proof bedding for flooring of Bath and WC 25
mm thick in C.M. 1:3 including using approved water proofing
compound in specified proportion as per manufacturers
specifications for per bag of cement including leveling, curing and
covering 10 years guarantee on court fee stamp paper of
Rs.500/including ponding test etc. complete.
347.59Rupees Three hundred Forty
Seven Paise Fifty Nine OnlyCum 85,956.37
28 215.58 Sqm
Providing cement based water proofing treatment to terraces
(Indian water proofing or alike) with brick bats laid in required
slope to drain the water for any span after cleaning the base
surface. Applying a coat of cement slurry admixed with approved
water proofing compound and laying the brick bats on bottom
layer in C.M.1:5 admixed with approved water proofing compound
filling up to half depth of brick bats, curing this layer for 3 days,
applying cement slurry over this layer joints of brick bats with
C.M.1:3 admixed with approved water proofing compound and
finally top finishing with average 20 mm. thick layers of same
mortar added with jute fiber at 1 Kg per bag including finishing the
surface smooth with cement slurry admixed with approved water
proofing compound. Marking finished surface with false squares
of 300mm x 300 mm. making the junctions at the parapet rounded
and tapered top for required height, with drip mould at the junction
of plaster and parapet and curing and covering 10 years
Guarantee against leakproofness on Court fee stamp paper of Rs.
500/including ponding test etc. complete.
670.86Rupees Six hundred Seventy
Paise Eighty Six OnlyCum 1,44,622.66
29 10.53 Sqm
Providing and applying water proofing treatment using
acrylic polymer modified cement based water proofing coating
with fibre glass mesh mixing at the rate of powder to liquid (2:1) by
weight covering 9 to 10 sqm /kg with two coat using Dr. Fixit or
alike of chemicals for masonry and concrete surface by brush
covering 7 years guarantee on Stamp Papers etc. complete.
726.60Rupees Seven hundred
Twenty Six Paise Sixty OnlySqm 7,651.10
30 787.87 Sqm
Providing internal cement plaster 12mm thick in single coat in
cement mortar 1:4 with neeru finish to concrete or brick surfaces,
in all positions including scaffolding and curing etc. complete.
174.30
Rupees One hundred
Seventy Four Paise Thirty
Only
Sqm 1,37,325.57
31 42.84 SqmProviding internal cement plaster 20mm thick in two coats in
cement mortar 1:4 without neeru finish, to concrete, brick surface,
in all positions including scaffolding and curing etc.complete.
292.24Rupees Two hundred Ninety
Two Paise Twenty Four OnlySqm 12,519.56
32 249.24 Sqm
Providing sand faced plaster externally in cement mortar
using approved screened sand, in all positions including base
coat of 15 mm thick in cement mortar 1:4 using waterproofing
compound at 1 kg per cement bag curing the same for not less
than 2 days and keeping the surface of the base coat rough to
receive the sand faced treatment 6 to 8 mm thick in cement
mortar 1:4 finishing the surface by taking out grains and curing for
fourteen days scaffolding etc.complete.
445.40Rupees Four hundred Forty
Five Paise Forty OnlySqm 1,11,009.27
33 660.00 SqmProviding flush grooved pointing with cement mortar 1:3 for
brick work including scaffolding and curing etc. complete.75.81
Rupees Seventy Five Paise
Eighty One OnlySqm 50,034.60
34 465.00 Sqm
Providing flush grooved pointing with cement mortar 1:3 for
stone masonry work including scaffolding and curing etc.
complete.
96.81Rupees Ninety Six Paise
Eighty One OnlySqm 45,016.65
35 1.00 RmtProviding neeru finish to plastered surfaces in all positions
including scaffolding and curing etc. complete.26.25
Rupees Twenty Six Paise
Twenty Five OnlyRmt 26.25
36 8.25 Rmt
Providing patti/ band 75mm wide on plastered surface 12 mm
to 15 mm thick in C.M. 1:3 line and level including neat finishing
scaffolding curing etc. complete.
22.15Rupees Twenty Two Paise
Fifteen OnlyRmt 182.74
37 16.50 Rmt
Providing patti/ band 150mm wide on plastered surface 12
mm to 15 mm thick in C.M. 1:3 line and level including neat
finishing scaffolding curing etc. complete.
44.31Rupees Forty Four Paise
Thirty One OnlyRmt 731.12
38 105.00 Sqm
Providing and fixing chicken mesh jali of 24 gauge, with about
30 cm. width at the junction of R.C.C members and brick work, of
approved quality including fixing mesh in position by necessary
drilling in concrete /B.B.masonry and or tying by binding wire etc.
complete.
94.50Rupees Ninety Four Paise
Fifty OnlySqm 9,922.50
39 23.77 Sqm
Providing and laying machine cut machine Polished Kota
stone flooring 25mm to 30mm thick and required width in plain/
diamond pattern on bed of 1:6 C. M. including cement float, filling
joints with neat cement slurry, curing, polishing and cleaning etc.
complete.
951.44Rupees Nine hundred Fifty
One Paise Forty Four OnlySqm 22,614.78
40 23.77 Sqm
Providing Mirror polishing to Kota Stone including using all
necessary stones and equipments cleaning, washing etc.
complete. For Flooring
236.25Rupees Two hundred Thirty
Six Paise Twenty Five OnlySqm 5,615.43
41 2.10 Sqm
Providing Mirror polishing to Kota Stone including using all
necessary stones and equipments cleaning, washing etc.
complete. For Skirting
52.50Rupees Fifty Two Paise Fifty
OnlyRmt 110.25
42 42.42 Sqm
Providing and laying vitrified mirror / glossy finish tiles
decorative type RAK/ Kajaria/ Nitco/ Asian or equivalent make
having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10
mm thickness and confirming to IS. 156222006 ( group Bla) of
approved make, shade and pattern for flooring in required position
laid on a bed of 1:4 cement mortar including neat cement float,
filling joints, curing and clearing etc. complete. a) Flooring
907.90Rupees Nine hundred Seven
Paise Ninety OnlySqm 38,513.12
43 6.35 Sqm
Providing and laying vitrified mirror / glossy finish tiles of
RAK/ Kajaria/ Nitco/ Asian or equivalent make having size 590
mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and
confirming to IS. 156222006 ( group Bla) of approved make,
shade and pattern for flooring in required position laid on a bed of
1:4 cement mortar including neat cement float, filling joints, curing
and clearing etc. complete.b) Skirting
1264.90
Rupees One Thousand Two
hundred Sixty Four Paise
Ninety Only
Sqm 8,033.38
44 1.49 Sqm
Providing and laying machine cut machine polished machine
cut Kota stone slabs 20 to 25 mm thick for treads and risers of
steps and staircases, with rounded nosing for the treads on a bed
of 1:4 cement mortar including cement float, filling joints with neat
cement slurry, curing, polishing and cleaning etc. complete.
1012.90Rupees One Thousand
Twelve Paise Ninety OnlySqm 1,504.16
45 4.43 Sqm
Providing and fixing machine cut machine polished 18 mm to
20 mm thick telephone black / Amba White / Cat bary brown / RBI
red / Ocean Brown granite stone for treads and risers of steps and
staircases of approved colour and shade with rounded moulding
and three grooved line for the treads on bed of 1:4 Cement mortar
including float filling joints with neat cement slurry curing polishing
and cleaning etc. complete.
3424.19
Rupees Three Thousand
Four hundred Twenty Four
Paise Nineteen Only
Sqm 15,157.18
46 7.89 Sqm
Providing leather finished polishing to Granite Stone slab by
continuous grinding in 4 coats of different bits to receive rough
and matt finish including buffing process before laying and fixing
of stone as per drawing and design, including cleaning, washing
and finishing etc. complete.
451.50Rupees Four hundred Fifty
One Paise Fifty OnlySqm 3,564.37
47 2.63 Sqm
Providing and fixing designer tiles of 22 mm thick of size 300x300
of approved make and shape & fixing in rustic+combi or as
desired pattern as per drawing on bed of 1:4 cement mortar
including cement float of required colour filling joints with neat
cement slurry curing and cleaning etc.complete as dir ted by
Engineer in charge including, unloading, transporting , all
necessary arrangement, all taxes, Octroi, tools, plants, Mach ery,
other fixtures & fasteners etc. complete.as per details & directed
by Engineer -in- charge.
870.54
Rupees Eight hundred
Seventy Paise Fifty Four
Only
Sqm 2,288.56
48 26.28 Sqm
Providing and laying vitrified rustic matt stone finish tiles of
RAK/Kajaria/ Nitco/ Asian or equivalent make having size 590 mm
to 605 mm x 590 mm to 605 mm of 8 to 10mm thickness and
confirming to IS. 156222006 (Group Bla) of approved make,
shade and pattern for flooring in required position laid ? on a bed
of 1:4 cement mortar including neat cement float,filling joints,
curing and cleaning etc. complete. a) Flooring
1590.40
Rupees One Thousand Five
hundred Ninety Paise Forty
Only
Sqm 41,803.19
49 193.91 Sqm
Providing and laying vitrified stone effect finish tiles of
RAK/Kajaria/ Nitco/ Asian or equivalent make having size 590 to
605 mm x 590 to 605 mm of 8 to 10 mm thickness and confirming
to IS. 156222006 (Group Bla) of approved make, shade and
pattern for flooring in required position laid on a bed of 1:4 cement
mortar including required position laid on a bed of 1:4 cement
mortar including neat cement float, filling joints, curing and
cleaning etc. complete a) Flooring
1852.90
Rupees One Thousand Eight
hundred Fifty Two Paise
Ninety Only
Sqm 3,59,292.13
50 45.87 Sqm
Providing and laying heavy duty Vitrified tiles for pavit of a
approved quality 100mm x 100mm x 16mm thk. flooring in
required position with readymade adhesive mortar of approved
quality on plaster of CM 1:2 including joints with white /colour
cement slurry cleaning curing complete .
1648.60
Rupees One Thousand Six
hundred Forty Eight Paise
Sixty Only
Sqm 75,616.34
51 15.00 Sqm
Providing and laying heavy duty Vitrified tiles for pavit of a
approved quality 200mm x 200mm x 16mm flooring in required
position with readymade adhesive mortar of approved quality on
plaster of CM 1:2 including joints with white /colour cement slurry
cleaning curing complete .Including all types of taxes
transportation and necessary scaffolding etc. complete as
directed by engineers incharge
1626.60
Rupees One Thousand Six
hundred Twenty Six Paise
Sixty Only
Sqm 24,399.00
52 2.25 Sqm
Providing and fixing 20 mm thick mirror polished machine cut Tel
black granite with base of 25 mm thick one side polished machine
cut kadappa for kitchen platforms of size 2.67 m x 0.75 m
including Vanity counterfacias and similar locations of required
size of approved shade ,colour and texture laid over 20 mm thick
base cement mortar 1:4 (1cement : 4 coarse sand ) with joints
treated with matching pigment, epoxy touch ups, including
rubbing, curing etc. Complete at all levels.
2991.81
Rupees Two Thousand Nine
hundred Ninety One Paise
Eighty One Only
Sqm 6,731.57
53 3.24 Sqm
Providing sills of required material 20mm to 25mm thick, on a bed
of cement mortar 1:4 including cement float, filling joints with neat
cement slurry, curing, polishing, rounding edges, cleaning
complete. a) Marble other than white makrana
2669.80
Rupees Two Thousand Six
hundred Sixty Nine Paise
Eighty Only
Sqm 8,650.15
54 16.20 Sqm
Providing sills of green marble stone 25 to 30 mm thick on bed of
1:4 cement mortar including both side half round moulding
,cement float ,filling joint with slurry,curing ,polishing and cleaning
complete.neat coloured cement slurry,curing, machine polishing
and cleaning etc. complete.
1796.00
Rupees One Thousand
Seven hundred Ninety Six
Only
Sqm 29,095.20
55 3.73 Sqm
Providing and fixing machine cut mirror polished 18 mm to
20 mm thick telephone black granite / Amba White / Cat bary
brown / RBI red / Ocean Brown granite stone partition with
rounding the edges etc. complete . Both side polish
3516.10
Rupees Three Thousand
Five hundred Sixteen Paise
Ten Only
Sqm 13,100.99
56 12.00 Sqm
Providing & fixing 20 mm thick YellowJaiselmer stone for cladding
in required position on plaster of 1:4 cement mortar including
scaffolding, filling joints with neat cement slurry , curing ru ing &
polishing complete. including necessary scaffolding , all nec ssary
arrangement, all taxes, Octroi, tools, plants, transport, Machinery
,other fixtures & fasteners etc. complete.as per details & dire ted
by Engineer -in- charge.
1794.00
Rupees One Thousand
Seven hundred Ninety Four
Only
Sqm 21,528.00
57 1.80 Sqm
Providing and fixing Floriana marble (Natural Marble) slab for
Dado/skirting in required position and pattern with necessary
groove in CM 1:4 including 20 mm cement mortar plaster with
neat coloured cement slurry cleaning polishing etc complete
including necessary cement slurry cleaning polishing etc complete
including necessary scaffolding, all necessary arrangement, all
taxes, Octroi, to s, plants, transport, Machinery ,other fixtures &
fasteners etc. complet as per details & directed by Engineer -in-
charge.
3025.00Rupees Three Thousand
Twenty Five OnlySqm 5,445.00
58 700.00 Sqm
Providing and fixing polished telephone black granite stone
cladding 20 mmthick in required position on plaster of 1:4 cement
mortar including scaffolding, filling joints with neat cement rry ,
curing polishing & cleaning etc. complete.as per details & directed
by Engineer -in- charge
3040.00Rupees Three Thousand
Forty OnlySqm 21,28,000.00
59 8.70 Sqm
Providing and fixing green marble of 18 to 20 mm thick for door
frame/ dado/ window boxing etc. On C.M. 1:6 including filling
joints with polymer base filler nosing the sharp edges wherever
necessary, curing, etc. complete.
1651.81
Rupees One Thousand Six
hundred Fifty One Paise
Eighty One Only
Sqm 11,56,267.00
60 62.54 Sqm
Providing and fixing Italia Glass Mosaic tiles equipments of
quantity and size (20 mmx20mmx 4mm thick) of tiles on vertical
faces of RCC wall in with ready made polymer modified adhesive
of approved quality including scaffolding ,cleaning etc. complete
including necessary scaffolding required for applying of paint
including all necessary arrangement, all taxes, Octroi, tools
plants, transport, Machinery ,other fixtures & fasteners etc.
complet as per details & directed by Engineer -in- charge. giving
10 years grantee on stam paper
2364.00
Rupees Two Thousand
Three hundred Sixty Four
Only
Sqm 1,47,844.56
61 10.53 Sqm
Providing and laying Polished Kota stone flooring With
HandCut Polished Kota Stones 25mm to 30mm thick and required
width in plain/diamond pattern on bed of 1:6 Cement mortar
including cement float, filling joints with neat cement slurry, curing,
cleaning and Mirror Polishing etc. complete NoteWater absorption
for item No,19 should not exceed 0.05%.( Item to be used with
prior permission of Superintending Engineer )
1040.69Rupees One Thousand Forty
Paise Sixty Nine OnlySqm 10,958.47
62 162.92 Sqm
Providing and laying Antiskid Ceramic tiles of approved quality
of company RAK / Kajaria / Nitco / Asian or equivalent make of
size 30 cm x 30 cm and confirming to IS 156222006 (GroupB IIA)
for antiskid flooring in required position laid on a bed of 1:4
cement mortar including cement float, filling joint with cement
slurry cleaning curing etc. complete.
1033.90
Rupees One Thousand
Thirty Three Paise Ninety
Only
Sqm 1,68,439.27
63 209.15 Sqm
Providing and fixing heavy duty inter locking concrete Gray
paving blocks of 80 mm thickness of having a strength of 300
kg/Sq.cm. of approved quality and shape on a bed of crushed
sand of 25 to 30 mm thick including skirting joints and cleaning
etc. complete.
694.59Rupees Six hundred Ninety
Four Paise Fifty Nine OnlySqm 1,45,275.51
64 209.15 Sqm
Providing and fixing heavy duty inter locking concrete
Coloured paving blocks of 80 mm thickness of having a
strength of 300 kg/Sq.cm. of approved quality and shape on a bed
of crushed sand of 25 to 30 mm thick including skirting joints and
cleaning etc. complete
717.69
Rupees Seven hundred
Seventeen Paise Sixty Nine
Only
Sqm 1,50,106.94
65 235.75 Sqm
Providing and fixing heavy duty inter locking concrete Rubber
mould glossy paving blocks of 80 mm thickness of having a
strength of 400 kg/Sq.cm. of approved quality and shape on a bed
of crushed sand of 25 to 30 mm thick including skirtingjoints and
cleaning etc. complete. (using 100% crushed sand)
961.29Rupees Nine hundred Sixty
One Paise Twenty Nine OnlySqm 2,26,624.12
66 24.28 Sqm
Providing & applying two coats of lead/zinc base oil paint/
bituminious paint of approved colour to new structural steel
work and iron work in buildings including scaffolding if
necessary, cleaning and preparing the surface etc. complete.
(excluding primer coat).
52.50Rupees Fifty Two Paise Fifty
OnlySqm 1,274.49
67 58.02 Sqm
Providing and applying two coats of synthetic enamel paint of
approved colour to new /old structural steel work and wood work
in buildings, including scaffolding if necessary, cleaning and
preparing the surface (excluding primer coat) etc.complete.
52.50Rupees Fifty Two Paise Fifty
OnlySqm 3,046.21
68 32.40 Sqm
Providing and applying two coats of textured synthetic paint of
approved shade and quality and one coat of primer before
applying textured paint including scaffolding if necessary
preparing surface by thoroughly cleaning oil, grease, dirt and
other materials as required, etc. complete.
126.00Rupees One hundred Twenty
Six OnlySqm 4,082.40
69 338.65 Sqm
Providing and applying two coats of appex Appex Ace white
exterior paint of approved manufacture and of approved colour
to the plastered surfaces including cleaning ,preparing the plaster
surface ,applying primer coat ,scaffolding if necessary , and
watering the surface for two days etc complete.
168.00Rupees One hundred Sixty
Eight OnlySqm 56,892.36
70 3,493.48 Sqm
Providing and applying two coats of exterior white weather
shield paint of approved manufacture and of approved colour to
the plastered surfaces including cleaning ,preparing the plaster
surface ,applying primer coat ,scaffolding if necessary , and
watering the surface for two days etc complete. NOTE: For Item
No. 15 to 18 prior approval of Superintending Engineer will be
necessary
152.25Rupees One hundred Fifty
Two Paise Twenty Five OnlySqm 5,31,881.64
71 6.00 Sqm
Providing and fixing plain zinc sheeting of 0.80 mm thick (22
B.W.G.) over the ridge hip or valley to galvanized iron sheet
roofing including all fastening and bolt galvanised iron screws and
bolts, lead and bitumen washers etc. complete.(Weight of 6.8
kg/sq.m.).
798.00Rupees Seven hundred
Ninety Eight OnlySqm 4,788.00
72 30.00 Sqm
Providing and fixing corrugated galvanised iron sheets of
0.63mm thick (24 B.W.G.) for roofing without wind tiles including
fastening with galvanised iron screws & bolts, lead & bitumen
washers as per drawing etc. complete.(Weight of 5.5 kg/sq.m.).
707.70Rupees Seven hundred
Seven Paise Seventy OnlySqm 21,231.00
73 6.00 Rmt
Providing and fixing valley gutter of 22 B.W.G. (0.8 mm) plain
galvanised iron sheets 120 cm wide with teak wood planking 20
mm thick including two coats of coaltarring the upper surface of
plank etc. complete. (excluding painting to underside of plank).
1837.50
Rupees One Thousand Eight
hundred Thirty Seven Paise
Fifty Only
Rmt 11,025.00
74 53.35 Sqm
Removing G.I. or A.C. sheet roofing including purlins,
principal rafters etc. including sorting serviceable and
unserviceable materials, stacking the same as and where directed
in the compound including scaffolding etc. complete.
43.05Rupees Forty Three Paise
Five OnlySqm 2,296.72
75 145.67 Sqm
Providing and fixing rolling shutter fabricated from steel laths
of minimum thickness 0.9 mm with lock plate of 3.15 mm
thickness reinforced with 35 x 35 x 5 mm angle section fitted with
sliding bolts and handles for both sides, deep M.S. channel
section of depth and thickness not less than 65 mm and 3.15 mm
respectively with hold fast arrangements, M.S. Bracket plate 300 x
300 x 3.15 mm minimum size and shape with square bar,
suspension shaft of minimum 32 mm diameter, hood cover of
M.S. sheet not less than 0.9 mm thickness and of any size at top
and safety devices including mechanical gear operation
arrangement consisting of worm gear wheels and worms of high
grade cast iron or mild steel and one coat of red lead primer etc.
complete. (I.S. 62481979) (Without mechanical gear)
2467.50
Rupees Two Thousand Four
hundred Sixty Seven Paise
Fifty Only
Sqm 3,59,448.13
76 5.04 Sqm
Providing and fixing M.S. grill door 24 kg/sqm of various size as
per detailed drawings without hot dip coating, iron fixtures and
fastenings and 3 coats of oil painting etc
2226.00Rupees Two Thousand Two
hundred Twenty Six OnlySqm 11,219.04
77 25.20 Sqm
Providing and fixing steel ventilator fully glazed partly fixed as
per detailed drawing without hot dip zinc coating including
fabricating glazing with plain / obscured glass panes and
approved type and quality and iron oxidized fixtures and fastening
oil paint 2 coats etc. complete.
2210.25
Rupees Two Thousand Two
hundred Ten Paise Twenty
Five Only
Sqm 55,698.30
78 9.00 Sqm
Providing and fixing in position. (as per I.S.1868 / 1982)
Aluminium sliding window of two tracks with rectangular
pipe 0.547 kg/Rmt. and window frame bottom track section 61.85
x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track
section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The
shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight
0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight
0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight
0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417
kg/Rmt. As per detailed drawings and as directed by Engineer in
charge with all necessary Aluminium sections fixtures and
fastenings such as roller bearing in nylon casting and self locking
catch fitted in vertical section of shutter including 5 mm thick plain
glass with all required screws and nuts etc, complete. With
colour Anodising with box.
4421.55
Rupees Four Thousand Four
hundred Twenty One Paise
Fifty Five Only
Sqm 39,793.95
79 7.65 Sqm
Providing and fixing in position. (as per I.S.1868 / 1982)
Aluminium sliding window of two tracks with rectangular
pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight
0.547 kg/Rmt. and window frame bottom track section 61.85 x
31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track
section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The
shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight
0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight
0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight
0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417
kg/Rmt. As per detailed drawings and as directed by Engineer in
charge with all necessary Aluminium sections fixtures and
fastenings such as roller bearing in nylon casting and self locking
catch fitted in vertical section of shutter including 5 mm thick plain
glass with all required screws and nuts etc, complete. With
powder coating with box
4578.00Rupees Four Thousand Five
hundred Seventy Eight OnlySqm 35,021.70
80 9.00 Sqm
Providing and fixing in position (as per 1868 / 1982) Alluminium
sliding window of three tracks with rectangular pipe 95 x
38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame
bottom track section 92 x 31.75 x 1.30 mm at weight 1.070
kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at
weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40
x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x
18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section
40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed
drawings and as directed by Engineerincharge with all necessary
Aluminium sections fixtures and fastenings such as roller bearing
in nylon casting and self locking catch fitted in vertical section of
shutter including 5 mm thick plain glass and aluminium mosquito
net shutter with stainless steel jail with all required screws and
nuts etc, complete. With colour Anodising with box
4168.50
Rupees Four Thousand One
hundred Sixty Eight Paise
Fifty Only
Sqm 37,516.50
81 5.40 Sqm
Providing and fixing in position (as per 1868 / 1982) Aluminium
sliding window of three tracks with rectangular pipe 95 x
38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame
bottom track section 92 x 31.75 x 1.30 mm at weight 1.070
kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at
weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40
x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x
18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section
40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed
drawings and as directed by Engineerincharge with all necessary
Aluminium sections fixtures and fastenings such as roller bearing
in nylon casting and self locking catch fitted in vertical section of
shutter including 5 mm thick plain glass and aluminium mosquito
net shutter with stainless steel jail with all required screws and
nuts etc, complete. With powder coating with box
5003.25
Rupees Five Thousand
Three Paise Twenty Five
Only
Sqm 27,017.55
82 7.20 Sqm
Providing and fixing in position aluminium fixed window fully
glazed of any size as per detailed drawing and as directed by
Engineerincharge with all necessary alluminium sections including
necessary fixtures and fastening such as 5 mm thick clear float
glass etc. complete. b) With powder coating Note While arriving at
the rate of item of item weight at 6.90 kg/Sqm is considered.
3769.50
Rupees Three Thousand
Seven hundred Sixty Nine
Paise Fifty Only
Sqm 27,140.40
83 15.39 Sqm
Providng and fixing in position anodised extruded aluminum
partitions, partly glazed and partly laminated having frame
made out of extruded tubular section of size 40 mm x 60 mm with
12 mm thick three layered flat pressed teak wood particle board
bonded with BWP type exterior grade phenol formaldehyde
synthetic resin conforming to IS 128231990, laminated on both
sides,Novateakor equivalent and 5 mm thick selected quality
plain/ float glass panels fixed with aluminum glass clips 12 mm x
12 mm and rubber cushioning beading to glass partitions as per
approved drawing etc. compete
2720.55
Rupees Two Thousand
Seven hundred Twenty Paise
Fifty Five Only
Sqm 41,869.26
84 24.28 Sqm
Providing and fixing mild steel grill work for
windows,ventilators etc. 20 kg/sqm as per drawing including
fixtures, necessary welding & painting with one coats of
anticorrosive paint & two coats of oil painting complete.
1380.75
Rupees One Thousand
Three hundred Eighty Paise
Seventy Five Only
Sqm 33,519.09
85 20.22 Sqm
Providing and fixing mild steel grill railing 20 kg/sq.m with
Ghana teak wood hand rail of size 75mm x 60 mm.and sill of
75mm.x 25 mm.and newel posts for staircases, including
fabricating, fixtures, erecting, painting the grill work with one coat
of anticorrosive paint and two coats of oil painting with approved
colour and polishing the sill, hand rail and the newel post with
french polish.
2094.75
Rupees Two Thousand
Ninety Four Paise Seventy
Five Only
Sqm 42,362.13
86 11.34 Sqm
Providing and fixing Country cut teak wood double or single
leaf second class fully panelled door shutter with 35mm thick
style and rail with 25 mm thick panels with openable fan light as
per detailed drawings. Excluding the door frame 60mm x 100mm
stainless steel fixtures and fastening and finishing the wood work
with oil painting 3 coats.
5670.00Rupees Five Thousand Six
hundred Seventy OnlySqm 64,297.80
87 3.15 Sqm
Providing and fixing single or double leaf panelled door shutter
excluding frame with glazed openable fanlight shutter 35 mm
thick as per detailed drawing consistingpanelled vertical styles
100 mm x 35 mm and lock and bottom rail 200 mm x 35 mm and
panels 12 mm thick both side commercial ply faced particle board
including stainless steel fixtures and fastening and T.W. beading
at junctions of panel inserts and as instructed by the Engineer in
charge including 3 coats of oil painting etc. complete.
3493.35
Rupees Three Thousand
Four hundred Ninety Three
Paise Thirty Five Only
Sqm 11,004.05
88 106.49 Sqm
Providing and fixing mild steel grill gate with angle iron frame
65 mm x 65 mm x 10 mm with iron bars at 150 mm C/C and
diagonal flats as per the detailed drawing including hinges, pivot
blocks locking arrangement welding, revetting with oil painting in
three coats of approved colour shade. (Weight of gate 35
kg/Sq.m.)
1878.45
Rupees One Thousand Eight
hundred Seventy Eight Paise
Forty Five Only
Sqm 2,00,034.26
89 383.07 Sqm
Providing and laying Box type waterproofing to the floors and
walls consist of water proofing layers of cement mortar 1:4 and
25mm th k above which rough Shahabad ladi (stone) of 25mm
thick and above this ladi 20 mm thick 1:4 cement mortar with
water proofing compound @1kg per cement bag including the
bottom mast layer at aggregates 6 cu.ft./ 10 Sq.m fixed in cement
slurry including cu g finishing etc. complete with 10 years
guarantee on required court fees stamps etc. complete. including,
unloading transporting all necessary arrangement, all taxes,
Octroi, tools, plants, Mach ery ,other fixtures & fasteners etc.
complete.as per details & dire ted by Engineer -in- charge.
742.00Rupees Seven hundred Forty
Two OnlySqm 2,84,237.94
90 21.00 Rmt
Providing and laying in trenches 15 mm dia. medium grade
having embossed as ISI Mark galvanised iron pipes of 1.25
kg/meter necessary fitting remaking good the demolished portion
with filling trenches and with primer of anticorrosive oil paint , 2
coats complete.
206.85Rupees Two hundred Six
Paise Eighty Five OnlyRmt 4,343.85
91 27.00 Rmt
Providing and laying in trenches 20 mm dia. medium grade
having embossed as ISI Mark galvanised iron pipes ?of 1.63
kg/meter necessary fitting remaking good the demolished portion
with filling trenches and with primer of anticorrosive oil paint , 2
coats complete.
241.50Rupees Two hundred Forty
One Paise Fifty OnlyRmt 6,520.50
92 30.00 Rmt
Providing and laying in trenches 25 mm dia. medium grade
having embossed as ISI Mark galvanised iron pipes ?of 2.49
kg/meter necessary fitting remaking good the ?demolished portion
with filling trenches and with primer of anticorrosive oil paint , 2
coats complete.
291.90Rupees Two hundred Ninety
One Paise Ninety OnlyRmt 8,757.00
93 26.00 Rmt
Providing and laying in trenches 32 mm dia.medium grade
having embossed as ISI Mark galvanised iron pipes ?of 3.20
kg/meter necessary fitting remaking good the demolished portion
with filling trenches and with primer of anticorrosive oil paint , 2
coats complete.
336.00Rupees Three hundred Thirty
Six OnlyRmt 8,736.00
94 8.00 No.Providing and fixing 15 mm dia. screw down bib/ stop tap of
brass including necessary socket union nut complete.211.05
Rupees Two hundred Eleven
Paise Five OnlyNo 1,688.40
95 15.00 No.Providing and fixing 20 mm dia. screw down bib/ stop tap of
brass including necessary socket union nut complete.260.40
Rupees Two hundred Sixty
Paise Forty OnlyNo 3,906.00
96 19.00 No.Providing and fixing 25 mm dia. screw down bib/ stop tap of
brass including necessary socket union nut complete.324.45
Rupees Three hundred
Twenty Four Paise Forty
Five Only
No 6,164.55
97 4.00 No.Providing and fixing screw down 15 mm dia. wheeled stop tap
of brass including necessary sockets/union nut complete231.00
Rupees Two hundred Thirty
One OnlyNo 924.00
98 4.00 No.Providing and fixing screw down for 20 mm dia. wheeled stop
tap of brass including necessary sockets/union nut complete.273.00
Rupees Two hundred
Seventy Three OnlyNo 1,092.00
99 6.00 No.Providing and fixing screw down for 25 mm dia. wheeled stop
tap of brass including necessary sockets/union nut complete.417.90
Rupees Four hundred
Seventeen Paise Ninety
Only
No 2,507.40
100 8.00 No.Providing and fixing screw down for 32 mm dia. wheeled stop
tap of brass including necessary sockets/union nut complete.386.40
Rupees Three hundred
Eighty Six Paise Forty OnlyNo 3,091.20
101 16.00 No.
Providing and fixing 15mm diameter concussion push button
type brass/gun metal selfclosing tap including necessary
socket complete.
241.50Rupees Two hundred Forty
One Paise Fifty OnlyNo 3,864.00
102 16.00 No.
Providing and fixing 25mm diameter concussion push button
type brass/gun metal selfclosing tap including necessary socket
complete
268.80Rupees Two hundred Sixty
Eight Paise Eighty OnlyNo 4,300.80
103 8.00 No
Providing and fixing White Glazed Earthenware full stall type
Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting,
inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia.
P.V.C flush pipe with fittings and flushing arrangement including
lead soil pipe, lead trap, soil pipe connectionup to the outside face
of the wall
4935.00Rupees Four Thousand Nine
hundred Thirty Five OnlyNo 39,480.00
104 4.00 No
Providing and fixing coloured glazed earthenware full stall type
Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting,
inlet pipes and stop tap brackets for fixing the cistern 32mm dia.
P.V.C. flush pipe with fittings and flushing arrangement including
lead soil pipe, lead trap soil pipe connection up to the outside face
of the wall.
7090.65Rupees Seven Thousand
Ninety Paise Sixty Five OnlyNo 28,362.60
105 4.00 No
Providing and fixing coloured glazed earthenware lipped flat
back/corner type urinal with PVC 5 liters flushing cistern with
fittings,capacity with fittings, inlet pipe and stop tap, brackets for
fixing the cistern, P.V.C. flush pipe with fittings including lead soil
pipe, lead trap and soil pipe connection up to the outside face of
the wall.
3404.10
Rupees Three Thousand
Four hundred Four Paise Ten
Only
No 13,616.40
106 26.00 No.
Providing and fixing White glazed with bottle trap earthenware
Wash Hand Basin of 55x40 cm size including cold water piller
taps, brackets, rubber plugs and brass chain, stop tap, chromium
plate bottle trap and necessary pipe connections including UPAC
waste pipe and trap upto the outside face of the wall, making
good the damaged surface, testing etc. complete. (BRAND
HINDWARE/ JOHNSON/PARRYWARE/ VIENA/ AMERICAN
STANDARiv)
4573.80
Rupees Four Thousand Five
hundred Seventy Three Paise
Eighty Only
No 1,18,918.80
107 5.00 No.
Providing and fixing Coloured glazed with bottle trap
earthenware Wash Hand Basin of 55x40 cm. size including
cold water piller taps, brackets, rubber plugs and brass chain,
stop tap, chromium plate bottle trap and necessary pipe
connections including UPAC waste pipe and trap upto the outside
face of the wall, making good the damaged surface, testing etc.
complete. (BRAND HINDWARE/ JOHNSON/PARRYWARE/
VIENA/ AMERICAN STANDARiv)
4657.80
Rupees Four Thousand Six
hundred Fifty Seven Paise
Eighty Only
No 23,289.00
108 1.00 No.
Providing and fixing white glazed earthenware sink 450mm x
200mm x 300mm including all connection of the G.I. supply and
lead waste pipes up to the outside face of the wall, cold water
chromium plated screw down bib tap, rolled steel or C.I. brackets,
rubber plug with chain and stop tap complete.
2205.00Rupees Two Thousand Two
hundred Five OnlyNo 2,205.00
109 1.00 No.
Providing and fixing 8cm C.I. Nahani Trap including C.I. grating
bend and piece of C.I. pipe upto the outside face of the wall
complete.
600.60Rupees Six hundred Paise
Sixty OnlyNo 600.60
110 16.00 No.
Providing and fixing 10cm C.I. Nahani Trap including C.I. grating
bend and piece of C.I. pipe upto the outside face of the wall
complete.
600.60Rupees Six hundred Paise
Sixty OnlyNo 9,609.60
111 4.00 No.
Providing and fixing 15cm x 10cm salt glazed stoneware gully
trap in cement concrete 1:4:8 outside the building including cast
iron grating in the sink, connecting glazed stoneware pipe, brick
masonry chamber with cast iron lid and cast iron grating for the
gully trap.
813.75
Rupees Eight hundred
Thirteen Paise Seventy Five
Only
No 3,255.00
112 24.00 Rmt
Providing and laying for 150 mm dia salt glazed stoneware pipe
including fittings Such as bends, tees, single junction, double
junctions laying, jointing (including excavation and refilling the
trenches) complete.
288.75
Rupees Two hundred Eighty
Eight Paise Seventy Five
Only
Rmt 6,930.00
113 4.00 No
Providing & constructing Brick Masonry Inspection Chamber
60cm x 45cm x 90cm including 1:4:8 cement concrete foundation
1:2:4 cement concrete channels half round G.S.W. pipes, Brick
Masonry, plastering from inside and airtight C. I. lid 65 kg with
frame fixed in cement concrete etc. complete.
3351.17
Rupees Three Thousand
Three hundred Fifty One
Paise Seventeen Only
No 13,404.68
114 4.00 No
Providing & constructing Brick Masonry Inspection Chamber
90cm x 45cm x 90cm including 1:4:8 cement concrete foundation
1:2:4 cement concrete channels half round G.S.W.pipes, Brick
Masonry, plastering from inside and C.I. lid cover 75 kg with frame
fixed in cement concrete.
3727.38
Rupees Three Thousand
Seven hundred Twenty
Seven Paise Thirty Eight
Only
No 14,909.52
115 2.00 No
Providing and constructing Brick Masonry inspection Chamber
90cm x 45cm including 1:4:8 C.C foundation, 1:2:4
C.C.channels/half round glazed stoneware pipe channel, salt
glazed stoneware intercepting trap with rodding pipe set in 1:4:8
cement concrete block, brick masonry plastering inside and
Outside, with C.I. lead cover with frame fixed in cement concrete.
8231.87
Rupees Eight Thousand Two
hundred Thirty One Paise
Eighty Seven Only
No 16,463.74
116 17.00 No
Providing and fixing 450mm x 550mm size superior type
Belgium mirror with 16mm dia. nickel plated towel rod etc.
complete.
420.00Rupees Four hundred Twenty
OnlyNo 7,140.00
117 9.00 Rmt
Providing, laying & fixing P.V.C. pipe of 32mm dia. with fittings
such as bends, tees, reducers, clamps, etc. including necessary
excavation, trench filling etc. complete.
58.80Rupees Fifty Eight Paise
Eighty OnlyRmt 529.20
118 9.00 Rmt
Providing, laying & fixing P.V.C. pipe of 75mm dia. with fittings
such as bends, tees, reducers, clamps, etc. including necessary
excavation, trench filling etc. complete.
225.75
Rupees Two hundred Twenty
Five Paise Seventy Five
Only
Rmt 2,031.75
119 15.36 Sqm
Providing and fixing partition with kadappa stone of all sizes
and 25 mm thick polished on both side and edges to original
including fixing in position in cement mortor 1:4 curing polishing,
cleaning etc complete.
798.00Rupees Seven hundred
Ninety Eight OnlySqm 12,257.28
120 25.00 No
Providing and fixing European type white glazed earthenware
coupled closet symphonic trap with symphonic low level white
glazed 10 litres cistern with black backlite seat with all necessary
pipe connection etc. complete.
4580.10
Rupees Four Thousand Five
hundred Eighty Paise Ten
Only
No 1,14,502.50
121 8.00 No
Providing and fixing Orissa type white glazed earthenware 575
mm water closet pan including S trap with earthenware foot rests,
cast iron soil and vent pipe upto outside face of the wall 1:2:4
brick bat lime concrete bedding without flushing tank and its
accessories etc. complete.
2711.10
Rupees Two Thousand
Seven hundred Eleven Paise
Ten Only
No 21,688.80
122 17.00 NoProviding and fixing chromium plated towel rod 16 mm dia and
75 cm. in length including all accessories complete.126.00
Rupees One hundred Twenty
Six OnlyNo 2,142.00
123 25.00 No.Providing and Fixing half turn 25 mm dia gun metal flushing
cock including all accessories etc. complete.357.00
Rupees Three hundred Fifty
Seven OnlyNo 8,925.00
124 4.00 No.
Providing and fixing 40 mm. dia Ball cock medium type with PVC
float including sockets & necessary fittings and tested as per
municipal requirements etc. complete.
601.65Rupees Six hundred One
Paise Sixty Five OnlyNo 2,406.60
125 76.00 Rmt
Providing and Fixing 110 mm diameter PVC Rain Water pipe
with necessary fittings such as bends, tees, single junctions,
slotted vent, clamps etc complete.
367.50Rupees Three hundred Sixty
Seven Paise Fifty OnlyRmt 27,930.00
126 76.00 Rmt
Providing and fixing P.V.C. Rain water pipes of 160mm outer
diameter and having wall thickness of 2.2 to 2.7 mm confirming to
I.S. 135921992 including proper rainwater receiving recess with
P.V.C. plug, bend, necessary fittings, such as, offsets, shoes,
inluding fixing the pipe on wall using approved wooden cleats
projecting 25mm to 40mm from face approved wooden cleats
projecting 25mm to 40mm from face of wall a fixing with clips of
approved quality and number ,filing the joint using rubber gasket
with solvent cement and properly resting the shoe of pipes on
C.C. or masonry blocks, including necessary scaffolding and
maintenance for 3 yrs for any leakages or dislocations of pipes.
All the P.V.C. fittings and additional 2 piece socket clips shall be
got approved from engineer in charge etc. complete. (The
contractor shall give 3 yrs guarantee bond for payment)
453.60Rupees Four hundred Fifty
Three Paise Sixty OnlyRmt 34,473.60
127 43.20 Rmt
Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil
vent/waste pipe and with necessary fixtures and fitting such as
bends, tees, single junctions, slotted vent, clamps etc. complete
299.25Rupees Two hundred Ninety
Nine Paise Twenty Five OnlyRmt 12,927.60
128 43.20 Rmt
Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil
vent/waste pipe and with necessary fixtures and fitting such as
bends, tees, single junctions, slotted vent, clamps etc. complete.
420.00Rupees Four hundred Twenty
OnlyRmt 18,144.00
129 20.00 Rmt
Providing and laying concrete pipes of I.S.NP. class of 100mm
diameter in proper line, level and slope including necessary
collars, excavation, laying, fixing with collars in cement mortar 1:1
and refilling the trench complete.
495.60Rupees Four hundred Ninety
Five Paise Sixty OnlyRmt 9,912.00
130 20.00 Rmt
Providing and laying concrete pipes of I.S.NP. class of 150mm
diameter in proper line, level and slope including necessary
collars, excavation, laying, fixing with collars in cement mortar 1:1
and refilling the trench complete.
247.80Rupees Two hundred Forty
Seven Paise Eighty OnlyRmt 4,956.00
131 1.00 No.
Providing and fixing stainless steel sink of size 600 x 510 x 200
mm of Nirali or equivalent make incluidng coupling, outlet pipe,
elbow and other necessary fitting, finishing etc. complete.
2940.00Rupees Two Thousand Nine
hundred Forty OnlyNo 2,940.00
132 8.00 No
Providing & fixing 15 mmconcealed stop cock of jaguarmake as
per jaguar catalogue no. 069 concealed stop cock reduced body
with necessary fittings as per drawing including all type of fixture &
fasteners & detail given & as directed by engineer in charge incl
ing all type of taxes, octroi, transportation, loading, unloading
stacking etc. complete.as per details & directed by Engineer -i
charge.
950.74Rupees Nine hundred Fifty
Paise Seventy Four OnlyNo 7,605.92
133 2.00 No
Providing and fixing 100 mm dia. chromium plated brass
showers rose to 15mm dia. supply pipe including necessary
bend and socket complete.
215.25Rupees Two hundred Fifteen
Paise Twenty Five OnlyNo 430.50
134 90.32 Cum
Dismantling brick masonry in lime or cement mortar and
stacking the materials as directed with all leads, lifts etc.
complete.
135.45Rupees One hundred Thirty
Five Paise Forty Five OnlyCum 12,234.45
135 1.05 Cum
Dismantling stone masonry in lime or cement mortar including
stacking the materials as directed with all leads, lifts etc.
complete.
170.10Rupees One hundred
Seventy Paise Ten OnlyCum 178.61
136 26.55 CumRemoving lime or lean cement concrete including stacking the
spoils as directed with all leads, lifts etc. complete.311.85
Rupees Three hundred
Eleven Paise Eighty Five
Only
Cum 8,280.41
137 0.60 CumRemoving rich mix cement concrete including stacking the
spoils as directed with all leads, lifts etc. complete.435.75
Rupees Four hundred Thirty
Five Paise Seventy Five
Only
Cum 261.45
138 25.00 NoRemoving doors and windows with frames and stacking the
materials as directed with all leads, lifts etc. complete.64.05
Rupees Sixty Four Paise
Five OnlyNo 1,601.25
139 31.00 NoRemoving ventilators and small windows with frame and
stacking the materials with all leads lifts etc. complete.64.05
Rupees Sixty Four Paise
Five OnlyNo 1,985.55
140 929.29 Sqm
Removing cement tiles, or marble or polished shahabad floor
or dado without bed concrete including stacking the materials as
directed with all leads, lifts etc. complete.
23.10Rupees Twenty Three Paise
Ten OnlySqm 21,466.49
141 693.91 SqmRemoving cement or lime plaster including disposing of the
spoils as directed with all leads, lifts etc. complete.12.60
Rupees Twelve Paise Sixty
OnlySqm 8,743.25
142 3.00 Rmt
Removing wire fencing with iron/C.C. fencing posts and
stacking the materials as directed with all leads, lifts etc.
complete.
10.50 Rupees Ten Paise Fifty Only Rmt 31.50
143 108.00 RmtRemoving iron pipe railing having wooden R.C.C. or C.C. or
iron posts and stacking the materials as directed etc. complete.10.50 Rupees Ten Paise Fifty Only Rmt 1,134.00
144 24.04 Rmt Removing cast iron or wrought iron or A.C. pipe and stacking 9.45Rupees Nine Paise Forty
Five OnlyRmt 227.18
145 42.29 Cum
Dismantling the R.C.C. work 1:2:4 and sorting out the materials
such as steel etc. as directed and stacking them within the
specified lead as directed etc. complete.
645.75
Rupees Six hundred Forty
Five Paise Seventy Five
Only
Cum 27,309.41
146 15.00 Rmt
Removing Np2 and Np3 class pipes including stacking at road
side as directed by the Engineer in charge. Upto 900mm dia. etc.
complete.
157.50Rupees One hundred Fifty
Seven Paise Fifty OnlyRmt 2,362.50
147 18.00 Rmt
Removing Np2 and Np3 class pipes including stacking at road
side as directed by the Engineer in charge. 900mm dia. And
above. etc. complete.
183.75
Rupees One hundred Eighty
Three Paise Seventy Five
Only
Rmt 3,307.50
148 29.00 No.
Removing Urinal Pans or Wash hand basin with frame
including disconnecting the sanitary and water supply
connections. removing the same carefully and stacking the
serviceable materials as and where directed including throwing
the unserviceable materials out side etc. complete.
52.50Rupees Fifty Two Paise Fifty
OnlyNo 1,522.50
149 27.00 No
Removing W.C. Pan including disconnecting the sanitary and
water supply connections, removing and breaking flooring and
bed concrete around pan removing the same carefully and
stacking the serviceable materials as and where directed
including throwing the unserviceable materials out side etc.
complete.
110.25Rupees One hundred Ten
Paise Twenty Five OnlyNo 2,976.75
150 6.00 SqmRemoving grass, gazer grass and disposing off out of building
premises including making clean the ground by shovel and6.30
Rupees Six Paise Thirty
OnlySqm 37.80
151 18.00 No
Dismantling existing brick bat coba in the W/C and toilets
including removing the dismantelled stuff outside the rooms,
including stacking and cleaning surface etc. complete.
1023.75
Rupees One Thousand
Twenty Three Paise Seventy
Five Only
No 18,427.50
152 24.00 Rmt
Providing and fixing 900mm high S.S.304 Grade Stainless
steel railing with 40mm diameter and 1.5mm thick at top,40mm
diameter and 1.5mm thick vertical supports spaced at 1.5m center
to center and 8mm thick toughened glass including fabricating
,fixtures, errecting , necessary welding , grinding , finishing,
buffing to stainless steel pipe etc. complete
4210.50Rupees Four Thousand Two
hundred Ten Paise Fifty OnlyRmt 1,01,052.00
153 1.00 Hr
Dewatering on BHP basis by using water pump including
diversion of stream, providing cofferdams, earthern bunds etc. as
may be necessary for foundation and other parts of the the works
and pumping out water during and after excavation as may be
required by using 5.0 to 9.0 BHP pump etc. complete.
136.50Rupees One hundred Thirty
Six Paise Fifty OnlyHr. 136.50
154 1.00 Rmt
Providing and casting in situ or precast tapering R.C.C. M20
Barrier type Kerb with gutter ( as per IRC 86 1983) embedded
125mm below ground level over M10
PCC finished neatly with
C.M. 1:2, setting the same in C.M. 1:2, including the required
excavation in any strata and removing the excavated stuff any
where in city and redoing the surface as specified and directed
by Engineering Incharge.
Using Concrete Batching and Mixing
Plant
709.80Rupees Seven hundred Nine
Paise Eighty OnlyRmt 709.80
155 8.00 Rmt
Providing and laying cement concrete pipe of IS 458:2003 NP2
class of 450mm diameter in proper line, level and slope
including providing and fixing collars in cement mortar 1:2 and
curing etc. complete.
1483.65
Rupees One Thousand Four
hundred Eighty Three Paise
Sixty Five Only
Rmt 11,869.20
156 10.00 Rmt
Providing and laying cement concrete pipe of IS 458:2003 NP2
class of 600mm diameter in proper line, level and slope
including providing and fixing collars in cement mortar 1:2 and
curing etc. complete.
2114.70
Rupees Two Thousand One
hundred Fourteen Paise
Seventy Only
Rmt 21,147.00
157 12.00 Rmt
Providing and laying cement concrete pipe of IS 458:2003 NP2
class of 800mm diameter in proper line, level and slope
including providing and fixing collars in cement mortar 1:2 and
curing etc. complete
3270.75
Rupees Three Thousand
Two hundred Seventy Paise
Seventy Five Only
Rmt 39,249.00
158 10.00 Rmt
Providing and laying cement concrete pipe of IS 458:2003 NP3
class of 600mm diameter in proper line, level and slope
including providing and fixing collars in cement mortar 1:2 and
curing etc. complete.
3598.35
Rupees Three Thousand
Five hundred Ninety Eight
Paise Thirty Five Only
Rmt 35,983.50
159 8.00 Rmt
Providing and laying cement concrete pipe of IS 458:2003 NP3
class of 800mm diameter in proper line, level and slope including
providing and fixing collars in cement mortar 1:2 and curing etc.
complete.
5821.20
Rupees Five Thousand Eight
hundred Twenty One Paise
Twenty Only
Rmt 46,569.60
160 8.00 Rmt
Providing and laying cement concrete pipe of IS 458:2003 NP3
class of 900mm diameter in proper line, level and slope including
providing and fixing collars in cement mortar 1:2 and curing etc.
complete
5913.60
Rupees Five Thousand Nine
hundred Thirteen Paise Sixty
Only
Rmt 47,308.80
161 34.13 Sqm
Providing and applying laying Aggregate plaster in granite /
marble stones, as decorative finish to give granite / marble like
appearance to concrete, brick or block surfaces in all position
including preparation of surface smoothly, evenly by racking of
joints in case of Brick or block work including backing layer of 12
mm thick with cement mortar 1:3 with 2% integral cement water
proofing compound, roughening for wall keying hardening and
drying the surface for a minimum five days gaps hardening and
drying the surface for a minimum five days gaps including second
coat of cement lime mortar into a proportion 1:4 preparing the
surface for three coat of marble finish plaster giving a thin coat of
white cement and two parts of course calcite powder, applying the
mortar with steel float on the surface in proper evenness applying
at coat of white cement and lime to set a smooth finish then
applying a thin coat of slurry made of white cement and black
oxide colour in required proportion by the steel float to get black
streaks on the surface and curing the surface for two days
including all materials and labour etc. complete.
915.59Rupees Nine hundred Fifteen
Paise Fifty Nine OnlySqm 31,244.51
162
Supplying & fixing in position Toilet Cubicle ( of follow g standard
dimension which includes 600mm door size width) made of heat,
bacteria, water, chemical, scratch and impact resistant 12mm
thick solid compact laminate panels including doors, pilasters &
intermediate panels finished with approved texture/shade as p r
the detail drawings & as per IS 2046 (Indian Standard) and as per
fire retardant BS-476/97 standard . TheproductshouldhaveGreen
Guard Certificate This also includes providing and fixing in
position necessary hardware made out of Stainless steel (Grade
304) as per
manufacturer?sspecifications&Architectsinstructionslike(1)Door
Knob, (2) Gravity Hinges, (3) Thumb turn lockset with Occupancy
indicators, (4) Coat hooks with Door stopper (5) U- Channels, (6)
Adjustable foot/pedestal, (7) Top rail with Corner con ctor (8)
Rubber noise deafening tape, (9) Screws & wall Plugs. The top
fitting should consist of SS round top rail which will get fixed w h
pilasters, with SS panel tube holder, SS corner bend (connected
ith top rail) will be used on the corner of cubicle in absence of
brick all, SS wall fixing is used only on the wall which will hold the
ss top rail. All screws will of 304 Grade in stainless steel with satin
finish. All
pilasters are supported by stainless steel Bottom Cladding. Th
base of the stainless steel bottom cladding will be anchored to the
floor with a clearance height up to 150 mm.
12.00 No.
A. Toilet Cubicle with standa dimension of 2025mm Height x
1000mmWidth x 1550mmDepth , which includes 600mm door
size width including all necessary arrangement, all taxes, Octroi,
ols, plants, transport, Machinery, other fixtures & fasteners
etc.complete as per details & directed by Engineer -in- charge.
31900.00Rupees Thirty One
Thousand Nine hundred OnlyNo 3,82,800.00
4.00 No.
Toilet Cubicle I-Shape (Front Partition with standard dimension of
2025mmHeight x 1000mm Width which includes 600mm door
size width including all necessary arrangement, all taxes, Octroi,
ols, plants, transport, Machinery,other fixtures & fasteners etc.
complete.as per details & directed by Engineer -in- ch rge.
27500.00Rupees Twenty Seven
Thousand Five hundred OnlyNo 1,10,000.00
All aspects specified by the manufactures, Greenlam Sturdo
Classique Evergreen series or equivalent Specs.:- Special
SpecificationNo.Vol.-II, 9)FurnitureWork, Page no.152.
163 100.65 Sqm
Engraving the Letters of size 1” height on granite slate including
oil painting to letter after engraving with all labour transporting
chain etc. Complete.
6500.00Rupees Six Thousand Five
hundred OnlySqm 6,54,225.00
164 288.12 sqm
Providing and fixing in position Glass Reinforced Concrete (GRC)
/ Glass Reinforced Polyester (GRP) covering for RCC column of
0.75 m dia & 8.3 m ht. with flutes , bases, top & capital as per
detailed design & drawing and at required position including al
taxes, octroi, transport, loading, unloading, all scaffolding &
necessary fixing arrangement, machinery, fixtures & fasteners
etc.complete. as directed Engineer in charge (The GRC/GRP
ingredients percentage should be confirmed by Engineer - in
charges) etc. complete. as per details & directed by Engineer -in-
charge. Mode of measurement :- surface area of column
(calculated by considering average diameter of column & average
height of column).
51500.00Rupees Fifty One Thousand
Five hundred Onlysqm 1,48,38,180.00
165 1455.85 Sqm
Providing & constructing waterfall of Ferro cement in natural stone
effect consisting of tor steel 8mm dia ,binding wire, cement mortar
in c.m 1.2,chicken mesh 12mm x 12mm,water proofing compound
,dry cement & natural stone effect painting/plastic emulsion paints
as per detailed drawing design ,curing cleaning complete as
directed by engineer in charge.(250mmthick)
1419.00Rupees One Thousand Four
hundred Nineteen OnlySqm 20,65,850.44
166 5.00 day
Hire charges for JCB including, operator, fuel, necessary
maintenance, accessories, transportation, all types of taxes etc
complete as directed by engineer incharge.
9078.00Rupees Nine Thousand
Seventy Eight Onlyday 45,390.00
167 15.00 Hr
Hire charges for drilling machine including, operator, necessary
maintenance, accessories, transportation, all types of taxes etc
complete as directed by engineer incharge.
1713.75
Rupees One Thousand
Seven hundred Thirteen
Paise Seventy Five Only
Hr 25,706.25
168 253.43 Sqm
Providing and fixing polished Telephone Black Granite Stone
flooring 18mm to 20mm thick laid to line to level with colour
pattern of granite flooring Inlay pattern work laid on cement 1:4
cement mortar Including cement float neat cement slurry including
cutting rounding edge polishing etc. Complete.
2500.00Rupees Two Thousand Five
hundred OnlySqm 6,33,572.50
Rs 3,78,05,725.30TOTAL OF SECTION A (CIVIL WORKS)
Item
No.Qty Unit Discription Per Amount
In Figures In Words
169 90.00 Cum
Providing earth work in embankment with approved materials
obtained from departmental land or other sources upto lead of
50m. including all lifts, laying in layers of 20cm. to
30cm.thickness breaking clods, dressing to the required lines,
curves,grades & section, watering and compaction with vibratory
roller with VSat attachment to achieve not less than 97 % of
standard proctor density etc. complete
472.75
Rupees Four hundred
Seventy Two Paise
Seventy Five Only
Cum 42,547.50
Spec : MORTH 305
170 100.00 Cum
GARDEN SOIL: Supplying on the site garden soil well sieved
90% to pass through I.S. sieve of 10mm size free from stones
rubbish like dried grass roots and other such materials. The soil
should be fresh from quarry. The colour of the soil generally be
red. The soil will be measured by measuring box. (Farma) (Item
includes Royalty charges, Transporting, loading unloading etc.)
lead charges for 30 k.m. Is considered
523.66
Rupees Five hundred
Twenty Three Paise
Sixty Six Only
Cum 52,366.00
PCMC - CIVIL WORK
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B
Memorandum showing the items of work to be carried out
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION B :- HORTICULTURE WORKS (PART A)
Estimated Rates
171 50.00 Cum
FARM YARD MANURE: Supplying on site well decayed, well
dried, well powdered, without clods and free from stones, dried
grass and other rubbish material. The colour of the manure
generally be black. The manure will be measured by measuring
box. (Farma) (Item includes Transporting, loading, unloading
etc.) lead charges for 30 k.m. Is considered
775.00
Rupees Seven
hundred Seventy Five
Only
Cum 38,750.00
172 200.00 Sqm
Preparing Lawn (30 cms. Depth) Excavating the ground to a
required depth of 30 cms, removing & conveying unwanted stuff
to a required distance as directed. Filling fresh garden soil/silt
and manure in excavated area in 3:1 proportion to a height of 30
cms. Mixing garden soil and manure thoroughly, well, levelling,
watering on previous night. Planting required variety of lawn
grass as directed and maintaining till well established by
watering, weeding, clipping, rolling, etc. Complete.
601.86
Rupees Six hundred
One Paise Eighty Six
Only
Sqm 1,20,372.00
173 100.00 Sqm
Preparing Instant Lawn: - Excavating the ground to a required
depth of 20 cm. Removing & conveying unwanted stuff to a
required distance as directed. Filling fresh garden soil & manure
in excavated area in 3:1 proportion to a height of 20 cm. Mixing
garden soil & manure thoroughly, well, leveling, wth required
slope, light watering on previous night, rolling, on surface, fixing
readymade lawn truf, rolls or slabs of required variety of lawn
grass as directed. Ramming on it for proper fixing and
maintaining till well established by watering, weeding, clipping
rolling, etc complete.
DSR
504.84
Rupees Five hundred
Four Paise Eighty
Four Only
Sqm 50,484.00
174 30.00 Sqm
Preparing Edging or Border: Excavating the ground to a
required depth of 20 cms., in the required area, removing and
conveying unwanted stuff, rubbish to the required distance as
directed. Filling the excavated part with fresh soil and manure in
3:1 proportion to a required height of 20 cms. Mixing, levelling,
watering the same. Planting rooted edging/border plants at
distance of 20 cms. Apart by watering, weeding, stirring of soil
replacing casualties, pruning if necessary etc. Complete.
430.29
Rupees Four hundred
Thirty Paise Twenty
Nine Only
Sqm 12,908.70
175 40.00 Sqm
Planting clipped Hedge: Excavating the ground to a required
depth of 30 cms, removing and conveying unwanted stuff to a
required distance as directed. Filling fresh garden soil and
manure in excavated area in 3:1 proportion to a height of 30
cms. Mixing garden soil and manure thoroughly well, levelling,
watering previous night. Planting hedge plants of required
species in two rows. Distance between two rows & between two
plants will be 25 cms. Maintaining till well established by
watering, weeding, stirring the soil and clipping if necessary etc.
Complete.
533.61
Rupees Five hundred
Thirty Three Paise
Sixty One Only
Sqm 21,344.40
176 150.00 Sqm
Preparing flower bed: Excavating the ground to the required
depth of 30 cms, Removing and conveying unwanted stuff to a
required distance as directed, Filling fresh garden soil and
manure in excavated area in 3:1 proportion to a required height
of 30 cms Mixing garden soil and manure thoroughly well,
levelling, watering on previous night. Planting seedlings of
required annuals 25 cms. Apart Maintaining till well established
by watering, weeding, stirring replacing of casualties etc.
Complete.
601.83
Rupees Six hundred
One Paise Eighty
Three Only
Sqm 90,274.50
177 27.00 Sqm
Preparing canna bed: - Excavating the ground to a required
depth of 30 cm. Removing & conveying unwanted stuff to a
required distance as directed. Filling fresh garden soil & manure
in excavated area in 2:1 proportion to a height of 30 cm. Mixing
garden soil & manure thoroughly, well, leveling, watering on
previous night. Planting well devoloped canna rhyzomes 40 cms
apart. Maintaining till well well established by watering, weeding,
stirring replacing of casualties etc, complete.
566.16
Rupees Five hundred
Sixty Six Paise
Sixteen Only
Sqm 15,286.32
178 30.00 Sqm
Preparing shrubbery: Excavating the ground to required depth
of 30 cms, removing and conveying unwanted stuff to a required
distance as directed. Filling fresh garden soil and Manure in
excavated area in 3:1 proportion to a height of 30 cms. Mixing
garden soil and manure thoroughly well, levelling, watering on
previous night. Planting well developed shrubs plants, 0.50 mtr.
Height, 0.45 Mtrs. Apart as directed and maintaining till well
established by watering, weeding, stirring, replacing casualties
etc. Complete.
547.26
Rupees Five hundred
Forty Seven Paise
Twenty Six Only
Sqm 16,417.80
179 25.00 No
Rose plant: - Excavating pit with size 0.3mx0.3mx0.3m .
Removing & conveying unwanted stuff to a required distance as
directed. Filling fresh garden soil & manure in excavated area in
3:1 proportion to a height of 30 cm. Mixing garden soil & manure
thoroughly, well, leveling, watering on previous night. Planting 40
to 50 cms height healthy plant of required rose variety and
maintaining till well well established by watering, weeding,
stirring, prunning replacing of casualties etc, complete.
178.64
Rupees One hundred
Seventy Eight Paise
Sixty Four Only
No 4,466.00
180 10.00 No
Planting large flowering/shady trees: (Minimum Height to 1
Mtr.) - Digging pit with size 0.9m x 0.9m x Height to 1 Mtr.) -
Digging pit with size 0.9m x 0.9m x 0.9m removing and
conveying unwanted stuff to a required distance as directed.
Filling the pit with approved excavated material upto a height of
0.30 m. and remaining height of 0.60 m. With fresh garden soil
and manure in 3:1 proportion. Mixing soil and manure
thoroughly well, leveling, as directed, watering previous night,
planting one to two year old, minimum 1.0 mtr. Height, healthy
tree sapling as per specifications. Maintaining till well
established by watering, weeding, stirring of soil, staking,
replacing of casualties etc. Complete.
728.16
Rupees Seven
hundred Twenty Eight
Paise Sixteen Only
No 7,281.60
181 10.00 No
Planting large flowering/shady trees: (Minimum height to 2 Mtr.) -
Digging pit with size 0.9m x 0.9m x0.9mremoving and conveying
unwanted stuff to a required distance as directed. Filling the pit
with approved excavated material upto a height of 0.30 m and
remaining height of 0.60 m. With fresh garden soil and manure in
3:1 proportion. Mixing soil and manure thoroughly well, levelling,
as directed, watering previous night, planting two or three year
old, minimum 2.0 mtr. Height, healthy trees sapling as per
specifications. Maintaining till well established by watering,
weeding, stirring of soil staking replacing of casualties etc.
Complete.
797.46
Rupees Seven
hundred Ninety Seven
Paise Forty Six Only
No 7,974.60
182 30.00 No
Planting small & medium size Ornamental / Flowering plant: -
Digging pit with size 0.6mx0.6mx0.6m. Removing & conveying
unwanted stuff to a required distance as directed. Filling the pit
with fresh garden soil & farmyard manure up to a height of 0.60
m. in 3:1 proportion. Mixing garden soil & manure thoroughly,
well, leveling, watering on previous night. Planting one to two
year old healthy tree saplings. Maintaining till well established by
watering, weeding, stirring replacing of casualties etc. complete.
409.61
Rupees Four hundred
Nine Paise Sixty One
Only
No. 12,288.30
183 50.00 Sqm
Preparing ground covers: Excavating the ground to a required
depth of 20 cms. Removing and conveying unwanted stuff,
rubbish to the required distance as directed. Filling the
Excavated area with fresh garden soil and F.Y. Manure in 3:1
proportion to a height of 20 cms. Mixing, levelling, watering the
same on previous night. Planting suitable ground covers as
directed in staggering pattern distance between two rows 25
cms., watering & maintaining till well established.
575.19
Rupees Five hundred
Seventy Five Paise
Nineteen Only
Sqm 28,759.50
Rs 5,21,521.22TOTAL OF SECTION B (HORTICULTURE ITEMS)
Item
No.Qty Unit Discription Per Amount
In Figures In Words
184 75.43 Sqm
Providing and fixing Ghana teak wood planking 25 mm thick for flooring
plained on both sides, tongued and grooved including scaffolding, if
necessary, and one coat of primer etc.
complete.
2079.00Rupees Two Thousand
Seventy Nine OnlySqm 1,56,818.97
185 50.43 Sqm
Providing & fixing of Rubber Mattin 8 mm thick of chequered or approved
design fixing with adhesive solution including, unlo ing transporting , all
necessary arrangement, all taxes, Octroi, tools,plants, Machinery ,other
fixtures & fasteners etc. comp te.as per details & directed by Engineer -in-
charge.
894.00Rupees Eight hundred
Ninety Four OnlySqm 45,082.19
186 1,433.41 Sqm
Providing and fixing frame work of anodised aluminium sections for
suspended false ceiling consisting of aluminium T 50 mm x 40 mm
weighing 0.39 kg/m. at 60 cms c/c & fixed with ( 15 x 15 mm) flanges
weighing 0.119 kg/m suspended on 6 mm dia. mild steel rod weighing
0.22 kg/m fixed on wall and beams including rounding of the edges with
aluminium T of 50 mm x 40 mm weighing 0.39 kg/m etc. including all
labour etc. complete.
849.45Rupees Eight hundred Forty
Nine Paise Forty Five OnlySqm 12,17,610.12
Memorandum showing the items of work to be carried out
PCMC - CIVIL WORK
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION C :- INTERIOR WORKS (PART A)
Estimated Rates
187 46.07 Sqm
Providing and fixing false ceiling of 15mm thick Acoustic tubular
Armstrong/ Everest/ AMS (0.60 x 0.60 m.) boards of approved make,
shape and sizes as per drawings including powder coated G.I. wall angle
of 20 mm x 20 mm x 0.60 mm size, G.I. grid runners of size 15 mm x 38
mm at 600 mm center to center both ways and suspended using G.I. 3
mm wire including fixing using butterfly clips and fasteners including
transporting, scaffolding all necessary labour and machinery, finishing
etc. complete.
1618.05
Rupees One Thousand Six
hundred Eighteen Paise Five
Only
Sqm 74,543.56
188 1,418.41 Sqm
Providing and fixing False ceiling of 12 mm thick Laminated board with
frame of M.S. angle 40 x 40 x 5 mm and Tee of size 40 x 40 x 6mm at 60
cm c/c including 12 mm dia. hangers, T.W. battens 50 x 25 mm and
beading 25 x 15 mm thick scaffolding if necessary, all Iron work etc.
complete.
1922.55
Rupees One Thousand Nine
hundred Twenty Two Paise
Fifty Five Only
Sqm 27,26,964.15
189 109.08 Sqm
Providng and fixing in position anodised extruded aluminum partitions,
partly glazed and partly laminated having frame made out of extruded
tubular section of size 40 mm x 60 mm with 12 mm thick three layered flat
pressed teak wood particle board bonded with BWP type exterior grade
phenol formaldehyde synthetic resin conforming to IS 128231990,
laminated on both sides,Novateakor equivalent and 5 mm thick selected
quality plain/ float glass panels fixed with aluminum glass clips 12 mm x
12 mm and rubber cushioning beading to glass partitions as per
approved drawing etc. compete
2720.55
Rupees Two Thousand
Seven hundred Twenty Paise
Fifty Five Only
Sqm 2,96,757.59
191 36.05 Sqm
Providing and fixing partitions made up of CCTW frame of size 75 mm x
50 mm at 60 cm c/c with 9 mm thick commercial ply and 4mm thick
veneer on both sides with French polish etc. complete.
4421.55
Rupees Four Thousand
Four hundred Twenty One
Paise Fifty Five Only
Sqm 1,59,388.03
192 19.25 Sqm
Providing & fixing 6mm thick mirror of size 1.82m x 1.21m fixed in frame
made in 19mm thick waterproof ISI Creative/Century make or equivalent
ply for all sides excluding backside.12mm waterproof ISI
Creative/Century make or equivalent ply for backside as per
drawing.1mm laminate of suede finish and ROYAL TOUCH
/CENTURYMICA make and Of approved shade for top. Pelmet of side
0.22m X 0.15 m made in 19mm thick waterproof ISI Creative/ Century
make of requirement ply for all sides finished in and ROYAL TOUCH
/CENTURYMICA make and of approved shade fixed on topside of mirror.
Mirror fixed with ½” x ½” L teakwood moulding. French polish for all
exposed surface of plywood. Polishing for lipping done in two coats of
melamine polish and Moulding as per drawing including. Nails, screws,
fevicol and necessary Labour etc complete as directed by the engineer in
charge. (Mode Of measurement as per front elevation).
4051.00Rupees Four Thousand Fifty
One OnlySqm 77,973.65
193 1.53 Sqm
Providing and fixing partition made up of 62.50X38.0X2mm thk section
with heavy duty glazing clips and 50mm thk glazing patti.38X25mm
aluminium angles and neccesary hardwares. The [partition should have
both side laminated. 12mm thk partical board in bottom and upper pannel
and 6mm clear glass in middle panel. Glass shall be fixed in 6mm thk
rubber gasket. All aluminium section exept angles shall be finished with
good quality powder coating of approved shade and colour. Glass shall
be of modi gaurd/asahi float or equalent make. Aluminium material shall
be of jindal/equalent make as approved by engineer in charge/architect.
Lamination of 1mm thick of approved shades and colours including all
taxes. Specifications: As directed by engineer incharge/architect.
3024.00Rupees Three Thousand
Twenty Four OnlySqm 4,613.72
194 4,004.56 Sqm
Providing and applying plastic emulsion paint of approved quality, colour
and shade to old & new surfaces in two coats including scaffolding,
preparing the surface. (excluding the primer coat)etc. complete
65.10Rupees Sixty Five Paise
Ten OnlySqm 2,60,696.99
195 1,272.41 Sqm
Providing and applying pearl/ luster finish paint of approved colour and
shade to the existing plaster surface including scaffolding, preparing the
surface, applying the acrylic wall putti etc. complete.
220.50Rupees Two hundred Twenty
Paise Fifty OnlySqm 2,80,565.96
196 79.16 Sqm
Providing and applying two coats of textured synthetic paint of approved
shade and quality and one coat of primer before applying textured paint
including scaffolding if necessary preparing surface by thoroughly
cleaning oil, grease, dirt and other materials as required, etc. complete.
126.00Rupees One hundred Twenty
Six OnlySqm 9,974.66
197 5,118.36 Sqm
Providing and applying plastic emulsion paint of approved quality, colour
and shade to old & new surfaces in two coats including scaffolding,
preparing the surface. (excluding the primer coat)etc. complete.
65.10Rupees Sixty Five Paise
Ten OnlySqm 3,33,205.24
198 140.12 SqmProviding and applying Wax polishing to the old wood work including
knotting, preparing the surface, scaffolding etc. complete as directed.31.50
Rupees Thirty One Paise
Fifty OnlySqm 4,413.78
199 140.12 Sqm
Providing and applying melamine polish of required finish to the wood
work by spray machine including knotting and preparing the even surface
by scraping, applying French polish , scaffolding if required etc. complete.
Note:The work to be executed on prior approval of Superintending
Engineer will be necessary.
687.75
Rupees Six hundred Eighty
Seven Paise Seventy Five
Only
Sqm 96,367.53
200 8.00 Nos.
Providing and fixing Country cut teak wood double or single leaf second
class fully panelled door shutter with 35mm thick style and rail with 25
mm thick panels with openable fan light as per detailed drawings.
Excluding the door frame 60mm x 100mm stainless steel fixtures and
fastening and finishing the wood work with oil painting 3 coats.
5670.00Rupees Five Thousand Six
hundred Seventy OnlyNos. 45,360.00
201 5.00 Nos
Providing and fixing solid core flush door shutter in single leaf 32 mm
thick decorative type of exterior grade as per detailed drawings approved
face veneers 3 mm thick on both faces or as directed, all necessary
beads, mouldings and lipping, wrought iron hold fasts, chromium plated
fixtures and fastenings, with brass mortise lock, chromium plated handles
on both sides, and finishing with French Polish etc. complete.
2449.65
Rupees Two Thousand Four
hundred Forty Nine Paise
Sixty Five Only
Nos 12,248.25
202 1.00 Nos
Providing & fixing door in required position of size 2.13m x 1.98m as
directed by engineer in charge in 12mm thick commercial ISI ply on both
sides of teakwood frame of size 0.15m x 0.03m finished in 1mm thick
laminate REALTOUCH make finish suede or equivalent. Door fixed in
frame of teakwood of size 0.07m x 0.15m covered with 12mm commercial
plywood finished with 1mm thick laminate REALTHOUCH make with 4” x
1’ x 1” SS pin brass hinges with steel AL drop and 6” tower bolt, brass
stopper with door closer. All necessary nails and screws and Fevicol used
as directed by the engineer in charge and as per requirement. etc.
complete.( As per Drawing enclosed approved rate.)
4640.00Rupees Four Thousand Six
hundred Forty OnlySQ.M. 4,640.00
203 7.00 Nos
Providing & supplying fully upholstered Sofa Set Godrej make ( Sofa Gold
Milan / Urban (Beverly) 3 seater sofa (1 Nos.) (W- 2.072m.x D-0.912m.x
H- 0.83m.) & ( W-1.572m.x D-0.912m.x H- 0.83m. ) with inside frame
made out of C.P. Teakwood and the front panel below seat seen from
outside to be made out of P.U. coated Pine wood with 4" thk. 'U' foam of
50 density for back, seat, & arms resp.with flat springs & foam covered
with white cloth and synthetic. Leather of approved colour & 4 shade with
SS finish designer legs etc. complete. including all necessary
arrangement, all taxes, transport, other fixtures & 4 fasteners etc.
complete as per details & directed by Engineer- In-Charge.
85131.00
Rupees Eighty Five
Thousand One hundred
Thirty One Only
Nos 5,95,917.00
204 2.00 Nos
Providing & supplying Media Centre (Godrej or similar Make) MODEL
FLUTE in Marin plywood with veneer/Laminate with melamine polish, all
brass fitting etc. Complete. Including of all taxes transport & other fixtures
& fasteners etc. Complete in all respect as directed by engineer in
charge.
54206.00Rupees Fifty Four Thousand
Two hundred Six OnlyNos 1,08,412.00
Specification
205 2.00 Nos
Providing & supplying Readymade CornerTable [Godrej or similar make)
size- w-0.440xd-0.450xht.-0.51m. in VIP Room made out of 19mm
waterproof ply and veneer finish with melamine polish. Brass fittings with
12 mm Glass top etc. complete. including all necessary arrangement, all
taxes, Octroi, tools, plants, transport, Mac inery, other fixtures & fasteners
etc. complete. as per details & direc by Engineer- In-Charge.
4448.00
Rupees Four Thousand
Four hundred Forty Eight
Only
Nos 8,896.00
206 5.00 Nos
Providing & fixing table for VIP of size 2'x2' corner table and 2'x'2 side
table (2 nos.) Both tables top are made in 12 mm glass of which is
vertically supported by 12 mm glass (Saint Gobain ) A teakwood f section
size 2"x2" is used as supporting / skirting leg etc. be pr ide as per drawing
All necessary nails ,screw, fevicol, araldite, a o tape, Octroi, other taxes,
transport, necessary labour and other fastening fixtures in S.S to be used
as per requiremen with providing white zink polishing for teak wood
lipping as per drawing and des n approved as per details & directed by
engineer in charge.
6911.00Rupees Six Thousand Nine
hundred Eleven OnlyNos 34,555.00
207 5.00 Nos
Providing & supplying Readymade Dressing Table [ Godrej make (Model
ADRIANA)] size- W- 0.441x D-0.468x Ht.-1.71M. in Guest Rooms made
out of 18mm waterproof ply and veneer finish with melamine polish.
Brass fittings with proper storage arrangement by providing drawers etc.
complete. including all necessary arrangement, all taxes, Octroi, tools,
plants, transport, Machinery
other fixtures & fasteners etc. complete. as per details & dire d by
Engineer- In-Charge Specs.:- Special Specification.
9157.00Rupees Nine Thousand One
hundred Fifty Seven OnlyNos 45,785.00
208 4.00 Nos
Providing and fixing and manufacturing on site side tale of size table of
size 1’4” x 1’6” with 2 drawers Table is made in 19mm thick waterproof
ISS Creative/century ply for sides,top and drawers faces. Also 12 mm
Thick waterproof ISI Creative/century ply for back of table and backside,
side & bottom of drawer 12” drawer channel. Drawer face is to be fitted
with S.S. nob, including teakwood lipping of 1”x 1/4” and finished with
1mm laminate of EURO /ROYAL TOUCH make suede finished and of all
lipping, and melamine polish for teakwood and exposed plywood
surfaces. With S.S locks, nails, screws, Fevicol and necessary labour(
Made of measurement as per top plans ) as per drawing, design and as
directed by engineer in charge etc. Complete.
7597.00
Rupees Seven Thousand
Five hundred Ninety Seven
Only
Nos 30,388.00
209 3.00 Nos
Providing & supplying Centre/ coffee Table Glow model of similar Godrej
make size (0.60x0.90x0.45)in VIP room made out of 19mm waterproof ply
and veneer finish with melamine polish. Brass fittings with 12 mm thick.
Glass top etc. complete. Including all taxes, transport & other fixtures &
fasteners complete. In all respect as directed by engineer in charge.
7008.00Rupees Seven Thousand
Eight OnlyNos 21,024.00
210 2.00 Nos
Providing & fixing iron table of size 1” x 3’3”. Top is made in 19mm thick
century / creative ply, supported with cross leg support o 19mm ply
century / creative ply, finished in 1mm thick laminate of EURO/ROYAL
TOUCH make and suede finish. With all necessary nails, screw, abro
tape ,favicol , aradiat, necessary labour and other required S.S fastening
fixtures as per Requirement.With providing white Zink polishing for teak
wood lipping, Table to be manufactured as per drawing and design
approved.(Mode of measurement as per top plan ) as directed by
engineer in charge tec. Complete.
2800.00Rupees Two Thousand
Eight hundred OnlyNos 5,600.00
211 2.00 Nos
Providing & fixing of size storage cabinet ( Between Staff Table) 1.75 (l) x
1.67 (H) x 00.45m (D) made out of 19mm commercial plywood for sides
and shelves excluding back side, 12mm commercial plywood for back
side, shutters made out of 12mm commercial plywood frame and 6mm
commercial plywood on both sides including B.T.W lipping of 1" X 1/4"
and 1 1/2" x 1/4" for fixing of hinges for the shutter as shown in drawing,
1.5mm laminate of royal touch or equivalent make and of approved
shade French polish for all exposed plywood surfaces as per drawing
including 3" x 1/2" x 1/4" S S pin brass hinges, brass oxidized handles &
tower bolt, locks nails, screws, fevicol and necessary labour etc.
complete incl ing all necessary arrangement, all taxes, Octroi, tools,
plants, t nsport, Machinery, other fixtures & fasteners etc. complete as
per deta s & directed by Engineer- In-Charge.
15360.00Rupees Fifteen Thousand
Three hundred Sixty OnlyNos 30,720.00
212 2.00 Nos
Providing & fixing storage cabinet of size 2.40(L)x0.75(H)x0.6M(d) made
out of 19mm commercial plywood for all sides and shelves excluding
back side 6mm commercial plywood for back side, shutters made out of
19mm commercial plywood including B.T.W lipping of 1” x 1/4 “ and 1 ¼
”x ¼” for fixing of hinges for the shutter as shown in drawing.1.5mm
laminate of royal touch or equivalent make and of approved shade and
French polish for all exposed plywood surfaces as per drawing including
3’ x ½’ x 3/4 “ S.S pin brass hinges, brass oxidizes handles & tower bolts,
locks, nails, screws, fevicol and necessary labour etc. complete. As
directed by.
9123.00Rupees Nine Thousand One
hundred Twenty Three OnlyNos 18,246.00
213 5.00 Nos
Providing & fixing Back storage for booking office of size 7” x 7” made in
19mm thick waterproof ISI Creative/Century make ply frame with top,
bottom, shelves and drawer back, side and backside of storage is made
up of 12mm waterproof ISI Creative / Century ply. Teakwood sections of
size 2”x3” are used for molding and other decorative work. Drawers fixed
with 20” telescopic drawer channels. Shutter are made of 19mm thick
waterproof ISI Creative / Century make.
With including edges covered in teakwood lipping of 1”x ¼” finished in
1mm thick laminate of EURO / TOUCH makes and suede finish. The
Drawer shutters are fitted with magnetic ball catch of S.S., 4” S.S
handles, and 4”x1/2”x3/4” S.S. hinges, with all necessary nails, screw,
favicol ,abro tape, araldiat , necessary labour as per requirement tec and
other S.S fastening fixtures as per requirement. White zink polishing for
teak wood lipping, melamine polish for all exposed surfaces of plywood
and teakwood. As per drawing and design approved.(Made of
measurement as per elevation) as per directed by engineer in charge tec.
Complete
13657.00Rupees Thirteen Thousand
Six hundred Fifty Seven OnlyNos 68,285.00
214 2.00 Nos
Providing & fixing table for staff of size1.52 x 0.60m. x 0.76m made in
19mm thick commercial ISI frame with 12mm thick commercial ISI ply for
front with keyboard drawer fixed with 12" drawer channels and 1 1/2" x
1/4" lipping finished in 1mm thick laminate REAL TOUCH make and
suede finish or Equivalent. Top of table covered with 8mm thick plain
glass (made- modiguard.) Edges covered in teakwood lipping of required
size (1" x 1/4"). All necessary nails, screw and other all taxes, transport,
fastening & fixture used as per design approved and requirement.
Polishing for moulding and lipping done in french polish etc. complete. as
per approved and as per details & directed by the engineer in charge.
4868.10
Rupees Four Thousand
Eight hundred Sixty Eight
Paise Ten Only
Nos 9,736.20
215 2.00 No
providing & fixing counter for Booking Office of Size 12'6"x2'6" with 8
drawers 3 keybord trays & 2 shutters with foot rest .counter is made in
19mm thk waterproof ISI Creative /Century make ply frame with shelves
and drawer face 12mm glass of bevil edge on counters top supported by
3" long SS studs of 2" dia drawers side back bottom and total back of
counter is manufactured with 12mm thick waterproof ISI creative / century
make ply fixed with 20" telescopic drawers channels with including edges
covered in teakwood lipping of 1" x1/4" finished in 1mm thick laminate of
make EURO/ ROYALTOUCH and suede finish skirting made up of
teakwood of section size 3"x2" the drawer shutters are fitted with
maganetic ball catch of s.s 4" ss handles and 4"x1/2"x3/4" ss hings with
necessary nails screw , fevicol required labour etc. and other S.S
fastening fixtures as per requirement white zink polishing for teak wood
lipping ,malamine polish for all exposed surfaces for plywood and
teakwood etc. complete as per drawing and design approved as per
details & directed by the enginners incharge.
15940.00Rupees Fifteen Thousand
Nine hundred Forty OnlyNo 31,880.00
216 6.00 Sqm
providing & fixing Working Counter Of Sizes 12'x2' for staff with 2 drawer
2 shuttered storage and 3 key board counters side top bottom footrest
vertical partitions ,drawer front orage shutters a made in 19 mm thick
waterproof ISI creative century ply forming main frame.Drawer side
,bottom,back total back of counter,keyboard bottom are made in 12mm
thk. waterproof ISI Creative/Century Ply. Drawer and keyboard are fixed
with 20" telescopic drawer channels .shutters are fitted with 4"x1/2"x3/4"
SS hinges,4"SS handle,magnetic ball catch. are covered with 1"x1/4"
teakwood lipping of required shape moulded counter is finished .1mm
thick laminate EURO /ROYAL TOUCH make and suede finish teakwood
section of size 3"x2" is used for required places as per drawing .All
nessacery nails ,screw, fevicol araldite,abro tape,necessary labour and
other fastening fixture in SS to be used as per requirement.With providing
white zink polishing for teakwood lipping ,melamine polish for all exposed
surfaces of plywood and teakwood . as per drawing and design approved
(Mode of measurement as per top plan) as per details.
14384.00
Rupees Fourteen Thousand
Three hundred Eighty Four
Only
Sqm 86,304.00
217 6.00 Nos
HIGH BACK CHAIR providing and planning in position chair of comfort
make) ( with gas lift technology for height adjustment bolt and 40 high
density foam for seat and back with cotton cloth, nylon stand,PU Castor,
wooden handle and black leather foam cover as per approved design
colour, style by the Engineer in charge all chairs are to be protected up to
the completion of work etc. complete. including all necessary
arrangement, all taxes, Octroi, tools plants,
transport, Machinery, other fixtures & fasteners tc.complete as per details
& directed by Engineer- In-Charge.
7572.00
Rupees Seven Thousand
Five hundred Seventy Two
Only
Nos 45,432.00
218 2.00 Nos
SEMIHIGHBACKCHAIR providing and planning in position chair of
comfort make) ( with gas lift technology for height adjustment and Frame
in 12mm MS bar with tilt mechanism and 40 high density foam for seat
and back with cotton cloth for cover chair with soft handle and revolving
type, PU Castor as per approved by Engineer in charge all chairs are to
be protected up to the completion of work etc. complete. including all
necessary arrangement, all taxes, Octroi, tools, plants, transport,
Machinery, other fixtures & fasteners etc.complete. as per details &
directed by Engineer- In-Charge.
5085.00Rupees Five Thousand
Eighty Five OnlyNos 10,170.00
219 20.00 Nos
Providing & fixing for SEATING ARRANGEMENT PEONS 1.80 x 0.40m x
0.40m made in 19mm thick commercial ISI ply with 19mm thick
commercial ISI ply for top/front with 6mm ISI Ply for back of box finished
in 1mm thick laminate make REAL TOUCH in suede finish or Equivalent.
Edges covered in teakwood lipping of required size (1" x 1/4").and L
teakwood moulding of size 1" x 1" x 2 1/2" 30 high density foam with
cover in cotton cloth of approved shade & colour. Shutter for storage
under the seating made out of 19mm thk commercial ply & finished with
1mm thick laminate of REAL TOUCH MAKE or equivalent. Shutter fixed
with 3" x 1/2" x 3/4" SS pin brass hinges including magnetic ball catch
and 4" brass oxidized handles and all necessary nails and screw etc
completed as directed by the engineer in charge. Polishing and finishing
complete with French polish etc.
5175.00Rupees Five Thousand One
hundred Seventy Five OnlyNos 1,03,500.00
220 23.00 Nos
Providing & planning in position chair of “Comfort” make Fixed type three
sealer M.S Powered Coated stand in With 2” x 1” 14 gauge pipe in centre
and 16 gauge 2” pipe at sides with Wooden seat and back in melamine
finished as per approved colour Shade by the engineer in Charge. All
Chairs are to protected up to the completion of work etc. Complete.
5417.00Rupees Five Thousand Four
hundred Seventeen OnlyNos 1,24,591.00
221 10.00 Nos
Providing and planning in position ( visitor ) chair of "Comfort" make
model No. Gp 1016 with fixed back executive of approved design colour
style and texture by the engineer in charge Chairs fitted with handles All
chairs are to protected up to the completion of work etc. complete.
1327.00
Rupees One Thousand
Three hundred Twenty
Seven Only
Nos 13,270.00
222 15.00 Nos
Providing & planning chair of “Comfort “ make, model No.GP1008 with
height adjustment facility and push back adjustment of approved design
color,Style and texture by the engineer in charge. All Chairs fitted with
fibre handles and revolving type wheels. All chairs are to protected up to
the completion of work etc.complete.
1548.00Rupees One Thousand Five
hundred Forty Eight OnlyNos 23,220.00
223 30.00 Nos
Providing & supplying Readymade single Bed [ Godrej make (Model
ADRIANA)] size- w-1.13xl-2.03xht.-0.93m. in Guest Rooms made out of
19 mm waterproof ply and veneer finish with melamine polish, Brass
fittings with proper storage arrangement by providing drawers etc.
complete. including all necessary arrangement, all taxes, Octroi, tools,
plants, transport, Machinery, other fixtures & fasteners etc. complete. as
per details & directed by Engineer- n- Charge. Specs.:- Special
Specification
16396.00
Rupees Sixteen Thousand
Three hundred Ninety Six
Only
Nos 4,91,880.00
224 128.52 Sqm
Providing supplying & fixing curtain double main silk and shear, silk tissue
as per approved lining with lace, beeds, tussles, with in usive of all taxes,
octroi, transport, etc and stitches, supply, fixi on site all window curtains
are to be maintained and protected up to the completion of work etc.
complete as per instruction and as per details & directed by engineer in
charge.
4295.00Rupees Four Thousand Two
hundred Ninety Five OnlySqm 5,51,993.40
225 6.00 Sqm
providing and making - fixing mural to be fixed on internal wall of ceramic
and siporex in 125 mm thk. with necessary colour pigments and refills
including scaffolding necessary fixture octroi, all taxes, VAT,
transportation etc. complete as per details & directed by engineer in
charge.( As per required size & shape).
44109.00
Rupees Forty Four
Thousand One hundred Nine
Only
Sqm 2,64,654.00
226 17.00 No
Fiber Moulding Picture Frame
Providing & Fixing in position 2’x2’x frames of 20mm fibre moulding, with
3mm non reflective glass, 3mm thick of hardboard on back, dry mount
imported posters.with inclusive of all taxes ,VAT,octory,transport, etc. all
posters are to be maintained and protracted up to the completion of work
etc. completion of work etc. complete as per instruction and as directed
by Engineer In charge.
18977.00
Rupees Eighteen Thousand
Nine hundred Seventy Seven
Only
No 3,22,609.00
227 40.50 Sqm
Providing ,designing, making, fixing and installing in pos ion as per
approved drawing of Mural to be fixed on external wall made up of mix
media like metal, siporex, fiber, glass & wood etc. including ultra violet
painting of approved colour & shade & make. Cleaning with all leads &
lifts including all necessary arrangement like machinery, scaffolding,
tools, plants, equi. taxes, Labour, etc. complete.as per details & directed
by Engineer - incharge. Specs.:- Special Specification .
22000.00Rupees Twenty Two
Thousand OnlySqm 8,91,000.00
228
providing and fixing illuminating accessories of family Windsor igloo
make, with inclusive of all taxes, VAT, Octroi, transport, tools, plants,
Machinery, other fixtures & fasteners etc. and satisfactory illumination
after fixing on site as per directio All illuminating accessories are to be
maintained and protected Up the completion of work etc.complete as per
details & directed by Engineer- In-Charge.
4.00 No a) crystal chandelier (8+4 ip) 98725.00
Rupees Ninety Eight
Thousand Seven hundred
Twenty Five Only
No 3,94,900.00
6.00 No b) crystal D/C walls fittings 10925.00Rupees Ten Thousand Nine
hundred Twenty Five OnlyNo 65,550.00
2.00 No c) 82743/8 LP chandelier DI casting 39675.00
Rupees Thirty Nine
Thousand Six hundred
Seventy Five Only
No 79,350.00
8.00 Nod) 82745 D/L wall fitting DI casting
5520.00Rupees Five Thousand Five
hundred Twenty OnlyNo 44,160.00
2.00 No
e) 8274 /5 LP chandelier DI casting
25300.00
Rupees Twenty Five
Thousand Three hundred
Only
No 50,600.00
6.00 No
f) 82747 hanging dom DI casting antique finish with white glass.
12875.00
Rupees Twelve Thousand
Eight hundred Seventy Five
Only
No 77,250.00
6.00 No
g) 83397 wall fitting SS finish
32775.00
Rupees Thirty Two
Thousand Seven hundred
Seventy Five Only
No 1,96,650.00
229 10.50 Sqm
Providing 25 mm to 30 mm thick partition of polished black kadappa
stone slab of approved quality including giving required size and shape
etc. Fixing in cement mortar 1:3 curing and cement etc. complete. b) Both
side polish
1158.85
Rupees One Thousand One
hundred Fifty Eight Paise
Eighty Five Only
Sqm 12,167.93
230 4.32 Sqm
Providing and fixing machine cut mirror polished 18 mm to 20 mm thick
telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown
granite stone partition with rounding the edges etc. complete. One side
polish
3258.85
Rupees Three Thousand
Two hundred Fifty Eight
Paise Eighty Five Only
Sqm 14,078.23
231 17.55 SqmProviding Halfround Moulding ( Full Moulding ) to 18 mm to 20 mm thick
granite stone including fine polishing and cleaning etc. complete128.10
Rupees One hundred Twenty
Eight Paise Ten OnlySqm 2,248.16
232 1.08 SqmProviding Fullround Moulding ( Full Moulding ) to 18 mm to 20 mm thick
Marble / Kota stone including fine polishing and cleaning etc. complete.108.15
Rupees One hundred Eight
Paise Fifteen OnlySqm 116.80
233 1.62 Inch
Providing & And fixing in position letters made from stainless steel with
buffering, of required size in height and font as directed And Approved by
the engineer in charge. Etc. Complete.
80.00 Rupees Eighty Only Inch 129.60
234 1,200.00Sq
Inch
Providing & fixing letter internal signage in stainless steel of 21 swg thick
stainless steel background and ingrowing black letters of required sizes
of approved shade , Colour font fixing with good quality stainless steel
screws as shown in the drawing as directed by engineer in charge in
clouding all type of taxes transportion and necessary scaffolding etc.
complete.
22.00 Rupees Twenty Two OnlySq
Inch26,400.00
235 18.90 Sqm
Providing and fixing in position of vertical blinds for windows fixed on
aluminium chanel with size of each blind is 4" width of approved colur and
shades and khadi fabric as directed by engineer incharge. All blinds are
to be protected upto the complition of work. etc complete.
1023.00Rupees One Thousand
Twenty Three OnlySqm 19,334.70
236 11.48 Sqm
Providing , supplying and fixing in position polypropylene (100%) carpet
of minimum thkness of 5mm and weighing 500grm/sqm of sapphire/
rosetta/obeetee/unitex or similar make with primary backing of pvc
reinforced glass fibre or bitumine binders of aprroved colour and design,
including all taxes transport,labour machinary fixtures and fastener etc.
complete as directed by engineer incharge.
1358.00
Rupees One Thousand
Three hundred Fifty Eight
Only
Sqm 15,589.84
237 5.00 Sqm
Providing , supplying and fixing in position polypropylene (100%) carpet
of minimum thkness of 5mm and weighing 500grm/sqm of element/
rosetta/obeetee/unitex or similar make with primary backing of pvc
reinforced glass fibre or bitumine binders of aprroved colour and design,
including all taxes transport,labour machinary fixtures and fastener etc.
complete as directed by engineer incharge.
931.00Rupees Nine hundred Thirty
One OnlySqm 4,655.00
238 2.00 No
Providing and fixing foldinng table of size 1.82mX0.6m X0.76 m made in
19mm thk commertial ISI ply finished in 1mm thk laminate make REAL
TOUCH in suede finish or equavalent. Edges covered in teak wood
lipping od required size (1"X1/4"). Edges of table top covered in 1"X1/2"
haf round moulding. 3"x1/2"X3/4" SS pin brass hinges for verticle and
horzontal flaps and 36"MS folding bracket made in 25mmX5mm patti and
all nessacery nails and srews etc completed as directed by the engineer
incharge. Polishing and finishing complete with freanch polish etc. ( as
per drawing enclosed aproved rate.)
3036.00Rupees Three Thousand
Thirty Six OnlyNo 6,072.00
239 1.00 No
Providing and fixing display board and table unit size 2.43mX0.90m made
up of 19mm thk marine ply of requisite manufactured
vizcorbett/anchor/centure/kenwood/duro or equivalent confirming to IS
303 /IS710-1980 with two ms square bars or vertical support from ceiling
finished with powder coated finished with 4mm thk match group smoke
veneers with grooves pattern of approved designs including all neccesary
accesaries and melanine polish. Below table dressing is made up of ms
square bar of size 25mmX25mm having weight 4.91kg/rmt and ms
powder coated perforated sheet including all neccesary fixtures,nut
bolting, welding etc. complete. Antitermite treatment to plywood and wood
works with 10year gaurantee bond etc. including all leads and lifts,
transportation, all types of taxes etc complete. All internally/externally
exposed face of plywood shall cover with lipping,( Burmah teakwood )and
shall be finished with melamine polish as per architects drawing and
instructions of engineer incharge. (Mode of measurment as per job unit.)
98174.00
Rupees Ninety Eight
Thousand One hundred
Seventy Four Only
No 98,174.00
240 5.00 No
Providing and fixing soft board of size 12'x1'6" with soft board on top
above 12mm thk waterproof ISI creative / century ply for frame. Plywood
edges are covered with 1" x 1/4" teak wood lipping of requitred shape,
mould. All nessacery nails srews fevicol, araldiat abro tap to be used as
per requirment and nessacery labour. with providing white zink polishing
for teakwood lipping. as per drawing and design approved( mode of
measurment as per front elevational area ) as directed by engineer
incharge etc. complete.
2681.00Rupees Two Thousand Six
hundred Eighty One OnlyNo 13,405.00
241 30.00 No
Providing flexi -coir matress with prorated 5 years gaurentee in 4" thkness
in aproved fabric colour, texture of century or equvalent make including
orthopedically designed for healthy sphine with unique combination of
traditional coir and state - of - the - art super bond inner core for optimal
support, premium jacquard fabric, quiltd on both side with high density
ultra soft flexi - puf for enchansed comfort etc as directed by engineer
incharge. including loading, unloading, transporting to site, octri and all
taxes etc. complete as per directed by engineer incharge.
8500.00Rupees Eight Thousand
Five hundred OnlyNo 2,55,000.00
242 29.40 Sqm
Providing and fixing lockers/storage of size 1.52mX2.13mX0.40m made
in 19mm thk waterproof ISI creative /centure make or equavalent ply of all
sides and sheleves including back side which is made up of 6mm
waterproof ISI creative /century make or equavalent ply shutters made
out of 19mm waterproof ISI creative/century make or equavalent ply
including teak wood lipping of 1"X1/4" and 1"X1/2" X1/4" for fixing of
hinges for the shutter as per drawings. 1mm laminate of suede finish of
royal touch/century mika make and of approved shade. French polish for
all exposed plywood surfaces polishing for lipping done in two coats of
melimine polish as per drawing 3"X1/2"X3/4" ss pin brass hinges,
oxidised handles (4") and locks, nails,screws, fevicoal and neccesary
labours etc complete as per directed engineer incharge. (Mode of
measurment: as per front elevation)
8717.00
Rupees Eight Thousand
Seven hundred Seventeen
Only
Sqm 2,56,279.80
243 1,200.00 No
Removing and reinstalling the existing chairs with transportations to and
fro to PCMC warehouse with loading unloading chairs including hardware
for re installation (without and repairs to chairs)
1062.00Rupees One Thousand Sixty
Two OnlyNo 12,74,400.00
Rs 1,26,51,803.05TOTAL OF SECTION C (INTERIOR ITEMS)
Item No. Qty Unit Discription Per Amount
In Figures In Words
244 632.06 Sqm
Fabric Panels on Side Walls-Providing & Fixing in position,
Acoustical Panelling made from 50mm acoustical fabric panels on G.
I. Frame of ceiling channels as per manufacturer’s specifications,
pervaded with 48 Kg /CuM glass wool 50 mm thick with first layer of
non woven acoustically transparent fabric and second layer of
acoustically transparent fabric of approved colour including cost of
required Cut-Outs, & Scaffolding, as per Architectural & Acoustical
Design & Instructions & Complete in all aspects.
5705.00
Rupees Five
Thousand Seven
hundred Five Only
Sqm 36,05,873.78
245 411.35 Sqm
Dado-Side Walls-Providing and fixing in position Acoustical panelling
made from prelaminated HDF partt panels mounted on GI carrier
and mounted on G. I. frame as per specification 600mm c to c and
chicken mesh on wall side, in front of 48Cum/50mm thick glass wool
Including cost of required cut-outs and scaffolding as per architectural
and acoustical design complete in all respects.
6530.00
Rupees Six Thousand
Five hundred Thirty
Only
Sqm 26,86,141.62
Memorandum showing the items of work to be carried out
PCMC - CIVIL WORK
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION D :- ACOUSTICAL WORKS (PART A)
Estimated Rates
246 87.84 Sqm
MDF designer -Acoustical wall Providing & fixing in position of MDF
designer panels made from 12mm MDf panels of density more than
780 Kg/cum Mounted on GI channels as per manufacturers
specifications , with 48kg/50mm glass wool ,Including primer and two
coats of color Including all cutouts , decorative moldings etc as per
architectural and acoustical design and complete in all respects.
7890.00
Rupees Seven
Thousand Eight
hundred Ninety Only
Sqm 6,93,057.60
247 919.42 Sqm
Providing & fixing in position, N-29 Perforated Plaster Board 595 x
595 With square , perforations 16% .12.5 thick on "T" Frame work
as per specification, with Glass wool of 48 kg/cum/50 mm thick , two
coats of paint including cost of required cut outs, decorative
moulding/finishing items and scaffoldings, as per Architectural &
Acoustical Design & Instructions and complete in all aspects.
3280.00
Rupees Three
Thousand Two
hundred Eighty Only
Sqm 30,15,681.20
248 134.46 Sqm
Acoustical Ceiling Providing & fixing in position, Plain Gypsum
Ceiling on G. I. frame as per specification, with Glass wool of 48
kg/cum- 50 mm thick , two coats of paint including cost of required
cut outs, decorative moulding/finishing items and scaffoldings, as per
Architectural & Acoustical Design & Instructions and complete in all
aspects.
1560.00
Rupees One
Thousand Five
hundred Sixty Only
Sqm 2,09,749.80
249 234.24 Sqm
Stage Floor-Providing & fixing in position Stage flooring using 37mm
thick (4''w x 5' L )Teak wood planks on 18 mm water proof ply
screwed to Teak wood frame of 50 x 50 mm wooden sections at
600mm c to c on stage surface including melamine polish, as per
Architectural & Acoustical Design & Instructions & Complete in all
aspects.
13780.00
Rupees Thirteen
Thousand Seven
hundred Eighty Only
Sqm 32,27,827.20
250 50.42 Sqm
Acoustical Door-Providing & Fixing in position, Acoustical Doors with
frame, using 50mm x 50mm Teak wood frame and 48kg/50mm thick
glass wool filled in 18 mm water proof plywood on both sides with
finish in veneer and final finish with melamine polish. The door should
have Brass Hinges, Handles, Door stoppers, Tower Bolts and
Andros as per Architectural & Acoustical Design & Instructions &
complete in all aspects.
20390.00
Rupees Twenty
Thousand Three
hundred Ninety Only
Sqm 10,28,145.36
251 282.43 Sqm
Carpet-Providing and fixing in position, heavy duty 100 %
polypropylene Carpet with 3 mm underlay, 980 gsm, 4 mtr width, fire
retardant, plain backing, needle punch technology, stain proof as per
Architectural & Acoustical design, instructions and complete in all
aspects. (Auditorium Plain Carpet)
1215.00
Rupees One
Thousand Two
hundred Fifteen Only
Sqm 3,43,146.38
252 720.68 Sqm
Carpet-Providing and fixing in position, heavy duty 100 %
polypropylene Carpet with 3 mm underlay, 980 gsm, 4 mtr width, fire
retardant, plain backing, needle punch technology, stain proof as per
Architectural & Acoustical design, instructions and complete in all
aspects. (Auditorium Designer Carpet)
1560.00
Rupees One
Thousand Five
hundred Sixty Only
Sqm 11,24,260.80
253 1.00 JobDismantling of Old Acoustics Ceiling,wall panel work , Stage Light ,
Stage Drapery, Audio System etc.205220.00
Rupees Two Lakh
Five thousand Two
hundred Twenty Only
Job 2,05,220.00
Rs 1,61,39,103.73TOTAL OF SECTION D (ACOUSTICAL WORKS)
Item
No.Qty Unit Discription Per Amount
In Figures In Words
254 1.00 No
Providing, Fixing, Testing & Commissioning in position of MAIN
CURTAIN IN VELVET-Main Curtain In Velvet In Single Colour Opening
Sideways, , Lining, Navar Hooks, Rings, Stitching Charges and Labour
Charges. Size:
15.50 x 6 mtr( Fabric FR Grade) including cost of necessary scaffolding
as per Architectural & Acoustical Design & Instructions Complete in all
aspects.
223085.00
Rupees Two Lakh
Twenty Three
thousand Eighty Five
Only
No 2,23,085.00
255 1.00 No
Providing, Fixing, Testing & Commissioning in position of MAIN
CURTAIN VALANCE
Main Valance In Velvet 15.50 x 1.20 mtrs. Lining, Stitching Charges,
Navar Belt and other, M.S. Pipe, Fitting Charges. (
Fabric FR Grade) with necessary scaffolding as per Architectural &
Acoustical Design & Instructions Complete in all aspects.
41505.00
Rupees Forty One
Thousand Five
hundred Five Only
No 41,505.00
256 1.00 No
Providing, Fixing, Testing & Commissioning in position of MAIN
CURTAIN -Track Main curtain sliding MS track with runners and pulleys
including cost of necessary Scaffoldings per Architectural & Acoustical
Design & Instructions & Complete in all aspects.
86120.00
Rupees Eighty Six
Thousand One
hundred Twenty Only
No 86,120.00
Memorandum showing the items of work to be carried out
PCMC - CIVIL WORK
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION E :- STAGE DRAPERY (PART A)
Estimated Rates
257 5.00 No
Providing, Fixing, Testing & Commissioning in position of INTERNAL
VALANCE- Internal blue valance size 15.50 x 1.2 mtrs including cost of
necessary scaffolding as per Architectural & Acoustical Design &
Instructions & Complete in all aspects.
34710.00
Rupees Thirty Four
Thousand Seven
hundred Ten Only
No 1,73,550.00
258 10.00 No
Providing, Fixing, Testing & Commissioning in position of SIDEWINGS
IN SINGLE COLOUR CLOTH- Side wings made in deodar wood of size
75mmx 40mm dark blue fabric on both sides with complete wing guides
and rails - size 5.00 x 1.20 mtrs ( Fabric FR Grade)as per Architectural &
Acoustical Design & Instructions & Complete in all aspects.
29105.00
Rupees Twenty Nine
Thousand One
hundred Five Only
No 2,91,050.00
259 5.00 No
Providing, Fixing, Testing & Commissioning in position of Property Pipe
bars with all ACCESSORIES - Including cost of necessary scaffolding
as per Architectural & Acoustical Design & Instructions & Complete in all
aspects.
13805.00
Rupees Thirteen
Thousand Eight
hundred Five Only
No 69,025.00
260 1.00 No
Providing, Fixing, Testing & Commissioning in position of CYCLORAMA
CURTAIN- Cyclorama curtain size 15.50 m x 6.50mtrs drop type with GI
pipes complete .( Fabric FR Griade) including cost of necessary
scaffolding as per Architectural & Acoustical Design & Instructions
Complete in all aspects.
52890.00
Rupees Fifty Two
Thousand Eight
hundred Ninety Only
No 52,890.00
261 1.00 No
Providing, Fixing, Testing & Commissioning in position of MIDDLE
CURTAIN -15.50 x 6.50mtrs drop type with GI pipes complete .( Fabric
FR Grade) including cost of necessary scaffolding as per Architectural &
Acoustical Design & Instructions & Complete in all aspects.
47715.00
Rupees Forty Seven
Thousand Seven
hundred Fifteen Only
No 47,715.00
262 1.00 No
Providing, Fixing, Testing & Commissioning in position of Back CURTAIN
- 15.50 x 6.50 mtrs drop type with GI pipes complete .( Fabric FR
Grade) including cost of necessary scaffolding as per Architectural &
Acoustical Design & Instructions & Complete in all aspects.
47715.00
Rupees Forty Seven
Thousand Seven
hundred Fifteen Only
No 47,715.00
263 1.00 No
Providing, Fixing, Testing & Commissioning in position of MAIN
CURTAIN COMPLETE MECHANISM MOTOR & ACCESSORIES -
Motorized mechanism for operation of main Velvet curtain with gear box
, 1 Hp motor Crompton make as per Architectural & Acoustical Design &
Instructions & Complete in all aspects.
239465.00
Rupees Two Lakh
Thirty Nine thousand
Four hundred Sixty
Five Only
No 2,39,465.00
264 13.00 No
Providing, Fixing, Testing & Commissioning in position of Automatic
OPERATED GEAR ARRANGEMENT Automatic gear box for top rolling
stands pulleys , drum pedestal , bearings and wire ropes complete with
fitting as per Architectural & Acoustical Design & Instructions & Complete
in all aspects.
186770.00
Rupees One Lakh
Eighty Six thousand
Seven hundred
Seventy Only
No 24,28,010.00
265 1.00 No
Providing & Fabricating Stage Mandap including cost of necessary
scaffolding as per Architectural & Acoustical Design & Instructions &
Complete in all aspects.
285345.00
Rupees Two Lakh
Eighty Five thousand
Three hundred Forty
Five Only
No 2,85,345.00
Rs 39,85,475.00TOTAL OF SECTION E (STAGE DRAPERY WORKS)
Item
No.Qty Unit Discription Per Amount
In Figures In Words
#REF! 282.00 Cum Payment towards royalty charges 141.34
Rupees One hundred
Forty One Paise Thirty
Four Only
Cum 39,857.88
Rs 39,857.88TOTAL OF SECTION E (ROYALTY)
PCMC - CIVIL WORK
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B
Memorandum showing the items of work to be carried out
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION F :- ROYALTY (PART A)
Estimated Rates
Project Name
Item No Items Amount1 PART A :- CIVIL WORKS 7,11,43,486.00
2 PART B :- ELECTRICAL WORKS 11,35,17,821.00
TOTAL AMOUNT OF RS 18,46,61,307.00
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B / ABSTRACT
Memorandum showing the items of work to be carried out
Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
TOTAL SUMMARY
Rupees Eighteen Crore Forty Six Lakh Sixty One thousand Three hundred Seven Only
Civil & Electrical Installation and Allied Works
Page 1 of 60
Project Name
Item No Items Amount
1 SECTION A :- ELECTRICAL WORKS 1,82,41,340.25
2 SECTION B :- FIRE WORKS 87,73,221.00
3 SECTION C :- HVAC WORKS 2,44,07,088.75
4 SECTION D :- SOUND SYSTEM WORKS 1,17,96,897.00
5 SECTION E :- STAGE LIGHTS 21,45,955.00
6 SECTION F :- SECURITY WORKS 2,02,40,107.00
7 SECTION G :- SOLAR WORKS 2,79,13,212.00
TOTAL AMOUNT OF RS 11,35,17,821.00
SAY 113517821.00
Rupees Eleven Crore Thirty Five Lakh Seventeen thousand Eight hundred Twenty One Only
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B / ABSTRACT
SUMMARY (PART - B ELECTRICAL WORKS)
Memorandum showing the items of work to be carried out
Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
Page 2 of 60
Item
No.Qty Unit Items Rate Amount
SUPPLYING INSTALLING TESTING AND
COMMISSIONING 3 WAY LINE ARRAY SPEAKER4,05,000.00
Mid Size Tri-Amplified 3-Way High Directivity Line
Array Element
The VT4888 is designed to deliver high-quality
reinforcement of music and speech in a variety of
applications including concert audio and corporate
A/V presentations of all types
LF (80Hz - 450Hz) 105dB (2.0V @ 4 Ohms)
MF (450Hz - 7kHz) 115dB (2.83V @ 8 Ohms)
HF (7kHz - 23kHz) 115dB (2.83V @ 8 Ohms),
LF @ 4 Ohms 2000W / 4000W
MF @ 8 Ohms 600W/1200W
HF @ 16Ohms 180w/360w
Continious Power
2000 W LF ,600 W MF ,150W HF
Dimensions (W x H x D) 990.6mm X 355.6mm X
508mm
(39 in x 14 in x 20 in)
Weight - 51.3 kg (113 lb)
MAKE JBL vt -4888 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING DUAL SUBWOOFER128000.00
A dual 18" high power subwoofer system in a front-
loaded,
vented enclosure designed for maximum low-
frequency performance.
Two drivers give 2,000 watts of continuous pink
noise power handling, 4kW program and 8 kW
peak.
frequencies for live music and a variety of sound
reinforcement applications.
Frequency Response (± 3 dB) 37 Hz-120 Hz
Sensitivity (1W/1m) 99 dB
Power Rating 2000 W / 4000 W / 8000 W
(Continuous/Program/Peak)
Rated Maximum SPL 138 dB SPL Peak
Nominal Impedance 4Ω
Input Connectors Two NL4
Operational Modes Subwoofer
Dimensions (H x W x D) 564 mm x 1137 mm x 714
mm
(22.2" x 44.8" x 28.1")
Net Weight 82 kg (180 lbs)
MAKE JBL-STX 828 OR EQUIVALENT
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B / ABSTRACT
Memorandum showing the items of work to be carried out
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION D :- SOUND SYSTEM WORKS (PART B)
24,30,000.00
2,56,000.00
FOUR LAKH FIVE
THOUSAND ONLY
ONE LAKH
TWENTY EIGHT
THOUSAND ONLY
NO
6
2
1
2
PCMC - ELECTRICAL WORKS
SOUND
Page 3 of 60
Item
No.Qty Unit Items Rate Amount
SUPPLYING INSTALLING TESTING AND
COMMISSIONING of Speaker For Dressing Room,
AV ROOM, LOBBY
13022.00
FREQUENCY RANGE
70 Hz - 23 kHz (-10 dB)
POWER CAPACITY
200 W Continuous Program Power; 100 W Continuous
Pink Noise
TRANSFORMER TAPS
70V: 60 W, 30 W, 15 W, 7.5 W
100V: 60 W, 30 W, 15 W
THIRTEEN
THOUSAND
TWENTY TWO
ONLY
MAKE JBL Control 25 T OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING36,040.00
Compact Cinema Surround
Speaker for Digital Applications
FREQUENCY RANGE (-10 DB):50 Hz - 20 kHz
FREQUENCY RESPONSE (±3 DB):65 Hz - 18 kHz
POWER RATING:150 watts continuous
pink noise:600 watts peak
MAKE JBL 8320 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING67,500.00
POWER AMPLIFIER FOR CONTROL 25
Extremely versatile; rated for 2-, 4-, 8-ohm loads
and 70V and 140V outputs
SIXTY SEVEN
THOUSAND FIVE
HUNDRED ONLY
MAKE CROWN CDI 2000 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING OF POWER AMPLIFIER4,89,714.00
four channel amplifier output 2150watts at 4ohms
THD at 1 kHz and 1 dB below clipping <0.05%
Frequency response (1 W into 8 ohms) +0/-3 dB
15 Hz - 27 kHz ,,FOR LINE ARRAY SPEAKER
MAKE CROWN I-TECH 4X3500HD OR
EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING POWER AMPLIFIER2,82,000.00
Dual Channel Power Amplifier, 2500 W@ 2 ohm,
4500 W@ 4 ohm,2100 W @ 8 ohm per channel
THD at 1 kHz and 1 dB below clipping <0.05%
Frequency response (1 W into 8 ohms) +0/-3 dB
15 Hz - 27 kHz FOR LINE ARRAY SUB WOOFER
MAKE CROWN I-Tech 9000HD OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING OF MONITOR SPEAKER1,56,700.00
15 in. Two-Way
Power Rating 800 W / 1600 W / 3200W
Stage Monitor
Compact and low-profile for minimal obstruction of
audience sightlines
2,82,000.00
6,26,800.00
1,30,220.00
1,44,160.00
67,500.00
19,58,856.00
THIRTY SIX
THOUSAND FORTY
ONLY
FOUR LAKH
EIGHTY NINE
THOUSAND SEVEN
HUNDRED AND
FOURTEEN ONLY
TWO LAKH EIGHTY
TWO THOUSAND
ONLY
ONE LAKH FIFTY
SIX THOUSAND
SEVEN HUNDRED
ONLY
NO
NO
NO
NO
NO
NO
10
4
1
4
1
4
3
4
5
6
7
8
Page 4 of 60
Item
No.Qty Unit Items Rate Amount
50 DEG x 90DEG nominal coverage
Bi-amplified or full-range passive operation
Differential Drive庐 woofer with neodymium magnet for high power capacity and very light weight
4" (voice coil) diameter compression driver with neodymium magnet
MAKE JBL VRX915M OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING SPEAKER1,01,500.00
SIDE FILL MONITOR
High output, 2-way loudspeaker systems combining
flexibility with high fidelity
Loudspeaker with 2 x 8” LF
Power Rating
375W Cont. Pink Noise
Attachment points for optional U-bracket, third part OmniMount type bracket and stand mount accessory
MAKE JBL AC28/26 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING MONITOR SPEAKER70,604.00
Dual Channel Digital Power Amplifier,
1600W@2 ohm, 1200W@4ohm,650W@8 ohm per
ch
Frequency response (1 W into 8 ohms) +0/-3 dB
20 Hz - 20 kHz
MAKE CROWN XTI4002 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING MIC MIXER1,88,820.00
MS 2200-3, 100-240V, 18 Mic/Line + 4 Mic/Stereo
Line Channels, 6 x AUX, Dual 24 bit Stereo Effects,
USB-Audio Interface
MAKE DYNACHORD CMS 2200 MKIII OR
EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING EQUILIZER45,500.00
Dual 31-Band Graphic EQ/Limiter with Type V™ NR
and AFS®
Advanced Feedback Suppression (AFS)
Type V Noise Reduction
MAKE DBX iEQ31 AFS OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING DIGITAL MIC MIXER CONSOLE2,71,555.00
40-input Digital Mixing Console and 32-in/32-out
USB Interface & IPAD CONTROL
Up to 80 channels to mix
32 Mic Inputs
8 XLR/1/4" Combi-jacks for line inputs and
instruments
40 DSP input channels (32 mono inputs and 4
stereo channels/returns)
31 Output busses (All with full DSP processing and
GEQ)
4-band Fully Parametric EQ on each channel and
bus
6,26,800.00
2,03,000.00
2,11,812.00
1,88,820.00
45,500.00
2,71,555.00
ONE LAKH FIFTY
SIX THOUSAND
SEVEN HUNDRED
ONLY
ONE LAKH ONE
THOUSAND FIVE
HUNDRED ONLY
SEVENTY
THOUSAND SIX
HUNDRED AND
FOUR ONLY
ONE LAKH EIGHTY
EIGHT THOUSAND
EIGHT HUNDRED
TWENTY ONLY
FORTY FIVE
THOUSAND FIVE
HUNDRED ONLY
TWO LAKH
SEVENTY ONE
THOUSAND FIVE
HUNDRED AND
FIFTY FIVE ONLY
NO
NO
NO
NO
NO
NO
4
2
3
1
1
1
8
9
10
11
12
13
Page 5 of 60
Item
No.Qty Unit Items Rate Amount
8 VCAs + 8 Mute groups
26 motorised faders (24 input + LR/Mono)
4 fully customisable Fader Layers
Built-in Stagebox Connectivity
5" touchscreen display
Multi-Colour LCD Channel Displays on each input
fader
4 studio-grade Lexicon Effects engines and
dedicated FX busses
BSS Graphic Equalisers on every bus
20 sub-group / aux busses
4 mono/stereo matrix busses
32x32 USB audio interface for multi-track recording
and playback *
MAKE SOUNDCRAFT SI IMPACT OR
EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING DIGITAL LOUD SPEAKER
MANAGEMENT SYSTEM
51,500.00
2 Input 6 Output
Digital speaker management
Features
Feedback Elimination
2.7 Seconds of Alignment and Zone Delay
RS-232 PC GUI control
Classic dbx Compression and Limiting
Graphic and Parametric EQ
Auto-EQ Function
Full Bandpass, Crossover, and Routing
Configurations
Auto Gain Control
Pink Noise Generator and fulltime RTA
Setup Wizard with JBL speaker and Crown Power
Amplifier Tunings
Security Lockout
Wall Panel Control Inputs
MAKE DBX Driverack 260 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING MOUNTING BRACKET2,46,500.00
This array suspension frame is crafted of 6061 heat-
treated aluminum. It includes 11 (eleven)
attachment holes for shackles, each fitted with
bronze bushings for long life. These holes are set on
approx. 4" centers. The VT4888-AF can also be
used to groundstack up to 6 enclosures. Also used
with VT4882 subwoofers. Weight: 38 kg (85 lb).
TWO LAKH FORTY
SIX THOUSAND
FIVE HUNDRED
ONLY
MAKE JBL VT 4888 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING WIRELESS MICROPHONE60,950.00
Transducer type :Moving coil (dynamic)
Polar pattern microphone
42 MHz bandwidth: 1680 tunable UHF frequencies
for interference-free reception
MAKE SENNHEISER EW 135 G3OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING WIRELESS MICROPHONE60,950.00
Polar pattern microphone
2,71,555.00
51,500.00
4,93,000.00
1,21,900.00
1,21,900.00
TWO LAKH
SEVENTY ONE
THOUSAND FIVE
HUNDRED AND
FIFTY FIVE ONLY
FIFTYONE
THOUSAND FIVE
HUNDRED ONLY
SIXTY THOUSAND
NINE HUNDRED
AND FIFTY ONLY
SIXTY THOUSAND
NINE HUNDRED
AND FIFTY ONLY
NO
NO
NO
NO
NO
1
1
2
2
2
13
14
15
16
17
Page 6 of 60
Item
No.Qty Unit Items Rate Amount
42 MHz bandwidth: 1680 tunable UHF frequencies
for interference-free reception
Enhanced frequency bank system with up to 12
compatible frequencies
High-quality true diversity reception
MAKE SENNHEISER EW 112 G3 OR
EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING WIRELESS MICROPHONE66,700.00
The included cardioid condenser headset
microphone is easy to wear, has great pop
protection and produces powerful sound. Also
included in this system is a stage-tested true
diversity receiver and a bodypack transmitter with
charging contacts for the optional BA2015
rechargeable battery.
· 42 MHz bandwidth: 1680 tunable UHF
frequencies for interference-free reception
· Enhanced frequency bank system with up to
12 compatible frequencies
· High-quality true diversity reception
· Pilot tone squelch for eliminating RF
interference when transmitter is turned off
· Automatic frequency scan feature searches
for available frequencies
MAKE SENNHEISER EW 152 G3 OR
EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING MICROPHONE CABLE84.00
INSTALLATION GRADE EIGHTY FOUR
ONLY
MAKE KRYSTAL OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING of High Flex 25/.10 mm x 2 core
ATC Lapp Shielded Digital Mic Cable Snake cable
24 pair
1,850.00
INSTALLATION GRADE CU WIRE with conduit
MAKE KRYSTAL OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING of Audio stage box with
significantly enhanced function
66,000.00
pairs of parallel connected XLR 3p. F/M can be
used as send or return
easy weight, solid chassis, black powder coating
MAKE KRYSTAL OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING of DI BOX14,800.00
Numerous applications can be satisfied by the AR-
133. For the traditional guitar use, the AR-133 can
be used with keyboards, DJ consoles, amplifier
outputs, and other electronic sources.
MAKE BSS -AR133 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING SHOTGUN MICROPHONE31,800.00
1,21,900.00
2,66,800.00
16,800.00
1,85,000.00
1,32,000.00
59,200.00
1,27,200.00
SIXTY THOUSAND
NINE HUNDRED
AND FIFTY ONLY
SIXTY SIX
THOUSAND SEVEN
HUNDRED ONLY
ONE THOUSAND
EIGHT HUNDRED
FIFTY ONLY
SIXTY SIX
THOUSAND ONLY
FOURTEEN
THOUSAND EIGHT
HUNDRED ONLY
MTR
NO
NO
NO
NO
NO
MTR200
100
2
4
4
2
4
17
18
19
20
21
22
23
Page 7 of 60
Item
No.Qty Unit Items Rate Amount
Super-cardioid/lobar microphone head suitable for
K6 and K6P powering modules. For reporting, film,
and broadcast location applications, as well as for
picking up quiet signals in noisy or acoustically live
environments.
THIRTY ONE
THOUSAND EIGHT
HUNDRED ONLY
MAKE SENNHEISER Me 66 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING POWER SUPPLYFOR
SHOTGUN MICROPHONE
26,850.00
Switchable bass roll-off filter protects against
rumble, handling, pop and wind noise
On/off switch
High output, low noise
Transformerless balanced output on 3-pin XLR
connector
MAKE SENNHEISER OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING BOUNDARY MICROPHONE21,500.00
MX393: Surface-mount mic; LED logic input/switch logic
output terminals, screw terminal connections, detachable
cable with XLR output connector
MAKE SHURE MX 393 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING WIRED MICROPHONE10,999.00
high-output vocal supercardioid dynamic
microphone, microphone, a shaped frequency
response ideal for close-up vocals.Dynamic
cartridge with supercardioid polar pattern
MAKE SHURE Beta 58 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING WIRED MICROPHONE8,113.00
Dynamic microphone (cardioid) for vocals and
instruments
Operating principle: Pressure gradient
, Polar pattern :Cardioid
Frequency response Close miking : 50 - 17,000 Hz ,
MAKE SENNHEISER E845 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING WIRED MICROPHONE14,624.00
Dynamic microphone (cardioid) for instruments
Operating principle: Pressure gradient
, Polar pattern :Cardioid
Frequency response Close miking : 40 - 18,000 Hz ,
MAKE SENNHEISER E604 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING GOOSENECK MICROPHONE35,000.00
Condenser microphohe (cardioid),for podium length
600 mm
3-pin XLR male with Transducer type: Electret
1,27,200.00
1,07,400.00
86,000.00
21,998.00
32,452.00
29,248.00
70,000.00
TEN THOUSAND
NINE HUNDRED
NINETY NINE ONLY
EIGHT THOUSAND
ONE HUNDRED
THIRTEEN ONLY
FORTEEN
THOUSAND SIX
HUNDRED AND
TWENTY FOUR
ONLY
THIRTY FIVE
THOUSAND ONLY
TWENTY ONE
THOUSAND FIVE
HUNDRED ONLY
TWENTY SIX
THOUSAND EIGHT
HUNDRED FIFTY
ONLY
NO
NO
NO
NO
NO
NO
NO2
2
4
4
4
2
4
23
24
25
26
27
28
29
Page 8 of 60
Item
No.Qty Unit Items Rate Amount
Condenser microphohe (cardioid), length 600 mm
3-pin XLR male with Transducer type: Electret
MAKE SENNHEISER MZH 3062 L OR
EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING GOOSENECK MICROPHONE
BASE
26,000.00
BASE FOR GOOSNECKTWENTY SIX
THOUSAND ONLY
MAKE SENNHEISER MZTX 31 PTTNX OR
EQUIVALENT
Supplying, erecting and commissioning of Drum Kit 1,24,000.00
4 pcs e 904 Tom microphone
1 pc e 906 Snare microphone
2pc e 914 Overhead microphone
MAKE SENNHEISER E900 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING DRUM KIT MICROPHONE 13,450.00
The open around ear headphones HD 559 is the
ideal choice for listeners seeking an optimal blend of
all-round performance and quality for home
entertainment.
THIRTEEN
THOUSAND FOUR
HUNDRED AND
FIFTTY ONLY
MAKE SENNHEISER HD 559 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING MICROPHONE STAND BIG7,834.00
Boom type powder coated alluminium tripoid
SEVEN THOUSAND
EIGHT HUNDRED
AND THIRTY FOUR
ONLY
MAKE K&M OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING MICROPHONE STAND SMALL7,834.00
Boom type powder coated alluminium tripoid
SEVEN THOUSAND
EIGHT HUNDRED
AND THIRTY FOUR
ONLY
MAKE K&M OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING SPEAKON CONNECTORS 8
POLE
1,984.00
COMPETE METAL BODY FOR LINER ARRAY
MAKE NEUTRIK NL-8 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING SPEAKON CONNECTORS 4
POLE
557.00
COMPETE METAL BODY FOR LINER ARRAY
AND STAGE MONITORS,POWER AMPLIFIERS
FIVE HUNDRED
AND FIFTY SEVEN
ONLY
MAKE NEUTRIK NL-4 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING XLR CONNECTORS557.00
1,24,000.00
13,450.00
31,336.00
31,336.00
11,904.00
27,850.00
1,11,400.00
70,000.00
52,000.00
THIRTY FIVE
THOUSAND ONLY
ONE LAKH
TWENTY FOUR
THOUSAND ONLY
ONE THOUSAND
NINE HUNDRED
AND EIGHTY FOUR
ONLY
NO
NO
NO
NO
NO
NO
NO
NO
NO200
2
2
1
1
4
4
6
50
29
30
31
32
33
34
35
36
37
Page 9 of 60
Item
No.Qty Unit Items Rate Amount
COMPETE METAL BODY CONNECTORS FOR
CONNECTING MICROPHONE AND INTERNAL
WIRING OF AMPLIFIERS
FIVE HUNDRED
AND FIFTY SEVEN
ONLY
MAKE NEUTRIK OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING SYSTEM RACK 42 U96,000.00
WITH GLASS LOCK DOOR AND FANS
MAKE CUSTOM OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING MULTIMEDIA PLAYER1,18,500.00
For playback of audio from cd mp3 and usb device
ONE LAKH
EIGHTEEN
THOUSAND AND
FIVE HUNDRED
ONLY
MAKE PIONEER DJ-R 1 OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING 2.5 SQ MM 6 CORE SPEAKER
CABLE
480.00
INSTALLATION GRADE CU WIRE with conduitFOUR HUNDRED
AND EIGHTY
SUPPLYING INSTALLING TESTING AND
COMMISSIONING 4 SQ MM 2 CORE SPEAKER
CABLE
325.00
INSTALLATION GRADE CU WIRE with conduit
KRYSTAL OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING 2.5 SQ MM 2 CORE SPEAKER
CABLE
230.00
INSTALLATION GRADE CU WIRE with conduit
KRYSTAL OR EQUIVALENT
SUPPLYING INSTALLING TESTING AND
COMMISSIONING POWER SAFE1,61,000.00
To Protect Audio System from high low voltage
fluctuation ,neutral cut ,and high low freqquency
3 Phase 189 Amps, Earth-Neutral, Voltage
Monitoring, Verifies proper earthing.
MAKE RAYTECH PS300 OR EQUIVALENT
providing OPERATOR CUM TECHNICIAN FOR
SOUND SYSTEM27000.00
Operation (for 8 hours a day/ 1ST shifts ) with
minor repairs like Wiring work/ Sound system ,
Maintainance on site.
TWENTY SEVEN
THOUSAND ONLY
providing OPERATOR CUM TECHNICIAN FOR
SOUND SYSTEM27000.00
Operation (for 8 hours a day/ 2ND shifts ) with
minor repairs like Wiring work/ Sound system ,
Maintainance on site.
TWENTY SEVEN
THOUSAND ONLY
1,17,96,897.00
46,000.00
1,61,000.00
9,72,000.00
9,72,000.00
1,11,400.00
96,000.00
1,18,500.00
1,92,000.00
97,500.00
ONE LAKH SIXTY
ONE THOUSAND
ONLY
NINETY SIX
THOUSAND ONLY
THREE HUNDRED
TWENTY FIVE
TWO HUNDRED
THIRTY ONLY
MTR
NO
MONTH
MONTH
NO
NO
NO
MTR
MTR
200
1
1
400
300
200
1
36
36
40
41
42
43
44
45
TOTAL SOUND SYSTEM WORK
Rupees One Crore Seventeen Lakh Ninety Six thousand Eight hundred Ninety Seven Only
37
38
39
Page 10 of 60
Item No. Qty Unit Items Rate Amount
1 3 No
Booster Pump of 900 LPM at average 40 m
Head, 12.5 HP either Monoblock or of suitable
HP with suitable Stages.
53038.00
( Ruppes Fifty three thousand &
thirty eight only )
1,59,114.00
2 3 No
Supplying and erecting fully Automatic
star/delta starter suitable for 12.5 H.P.
H.P. for 3 phase squirrel cage motor totally
enclosed with overload and no volt relay
complete erected on provided angle iron frame.
(similar to L & T make MK-1 FASD model.)
7625.00
( Ruppes Seven thousand &
twenty five only )
22,875.00
3 90 M
Supplying and erecting flat flexible 3 core 6 sq
mm PVC sheathed submersible type copper
cable suitably clamped at fixed intervals with
column pipe assembly complete.
258.00
( Rupees Two hundred fifty
eight only )
23,220.00
4 3 No
Supplying & Installing cast iron double flange
butterfly valve of size 100 mm dia. as per
specification No. FF-VL/BFV
3906.00
( Ruppes Thirty Nine thousand
& six only )
11,718.00
5 3 No
Supplying & Installing cast iron double flange
butterfly valve of size 150 mm dia. as per
specification No. FF-VL/BFV
6022
( Ruppes Six thousand & twenty
two only )
18,066.00
6 12 No
Supplying and installing Stainless
Steel single outlet hydrant valve fitted with
necessary accessories complete as per
specification No. FF-VL/HV
5637.00
( Ruppes Five thousand & thirty
seven only )
67,644.00
PCMC - ELECTRICAL WORK
Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION B :- FIRE WORKS (PART B)
( A ) Internal Hydrant System
Project Name
SCHEDULE B / ABSTRACT
Memorandum showing the items of work to be carried out
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
Page 11 of 60
7 12 No
Supplying and erecting one no. Brass orifice
plate having 6 mm. thickness, 140 mm outer dia
of 140 mm at every single outlet hydrant valve
as per specification No. FF-FFA/OP
997.00
( Ruppes Nine hundred & ninty
seven only )
11,964.00
8 12 No
Supplying fire fighting R.R.L. Hose pipe,
63mm dia,15m in length, fitted with necessary
accessories complete as per specification no.
FF-FFA/RRL
5423.00
( Rupees Five thousand four
hundred & twenty three only )
65,076.00
9 12 No
Supplying Stainless Steel branch Pipe 63 mm
Ø fitted with 20 mm dia detachable hexagonal
nozzle as per specifications No. FF-FFA/NZ
1903.00
( Rupees one thousand nine
hundred & three only )
22,836.00
10 12 No
Supplying and erecting M.S./CRCA cabinet for
housing single hydrant valve (size 400 x 400
x 400mm.) made from 16 SWG sheet and angle
iron 25 mm. x 25 mm. x 4 mm. having front
doors with viewing glass (8"x6") and locking
arrangement with necessary fixing material
such as rubber bidding etc. duly painted in post
box red colour.
5187.00
( Rupees Five thousand one
hundred & egight seven only )
62,244.00
11 12 No
Supplying and installing wall mounting
swinging Hose reel drum fitted with 19 mm
dia. 30m high pressure polypropylene
(Polyhose) long fitted with necessary accessories
complete as per specification No. FF-FFA/HV
7158.00
( Rupees Seven thousand one
hundred & fifty eight only )
85,896.00
12 30 No
Supplying and erecting ABC powder type fire
extinguisher as per IS : 13849 /15683 of 6 kg
capacity with necessary clamp for erection on
wall.
4475.00
( Rupees Four thousand four
hundred & seenty five only )
1,34,250.00
13 10 No
Supplying & erecting Carbon Dioxide (CO2)
fire extinguisher of 4.5 kg. Capacity Cartridge
type conf. To IS 2878 /15683 Complete
erected with necessary clamp made front 50x6
mm. M. S. flat with nut & bolts grouted in wall
complete.
12924.00
( Rupees twelve thousand nbine
hundred & twenty four only )
1,29,240.00
14 30 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 80 mm dia
with necessary fittings as per specification No.
FF-PP
937.00
( Rupees Nine hundred & thirty
seven only )
28,110.00
Page 12 of 60
15 36 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 100 mm dia
with necessary fittings as per specification No.
FF-PP
1273.00
( Rupees one thousand two
hundred & seventy three only )
45,828.00
16 90 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 150 mm dia
with necessary fittings as per specification No.
FF-PP
1812.00
( Rupees one thousand eight
hundred & twelve only )
1,63,080.00
17 3 No
Supplying and erecting 20/25mm Ø G.M.air
release Valve with necessary G.I. coupling tobe fitted on top of Air
vessel or on wet riser as
per specification No. FF-FFA/ARV
807.00
( Rupees eight hundred & seven
only )
2,421.00
18 8 No
Providing Round bottom FIRE Bucket of 9
Litres capacity as per IS : 2546 made out of
24 gauge G.I. sheet with extra handle at bottom
duly painted white inside and red outside with
FIRE Mark, on provided stand/ wall hook.
775.00
Rupees Seven hundred &
seventy five only
6,200.00
19 2 No
Providing Floor mounting stand for keeping
4 Nos. of FIRE buckets 1500mm in length,
900mm in height frame made out of 30x30x4
mm angle iron with cross supports for legs,
welded with 4 hooks and duly painted with
one coat of red lead and two coats of silver
paint.
3298.00
Three thousand two hundred &
ninty eight
6,596.00
20 20 No
Fire Resisting paint for electric cable. Often the source of a fire, CBRI
approved
7200.00
(Rupees Seven thousand two
hundred only)
1,44,000.00
21 15 No
Fire Retardant Spray For (Most) Fabrics Fire Extinguishing Spray &s
discharge time is 4 times longer than traditional fire extinguishers
allowing you to fight fires longer. minimum of approximately 32 seconds
vs. approximately eight seconds.
6500.00
(Rupees six thousand fifty only)97,500.00
13,07,878.00
Item No. Qty Unit Items Rate Amount
1 4 No
Supplying & Installing cast iron double flange
butterfly valve of size 150 mm dia. as per
specification No. FF-VL/BFV
6022
( Ruppes Six thousand & twenty
two only )
24,088.00
Sub Total (A) Rs
( B ) External Hydrant System
Page 13 of 60
2 10 No
Supplying and installing Stainless
Steel single outlet hydrant valve fitted with
necessary accessories complete as per
specification No. FF-VL/HV
5637.00
( Ruppes Five thousand & thirty
seven only )
56,370.00
3 10 No
Supplying and erecting one no. Brass orifice
plate having 6 mm. thickness, 140 mm outer dia
of 140 mm at every single outlet hydrant valve
as per specification No. FF-FFA/OP
997.00
( Ruppes Nine hundred & ninty
seven only )
9,970.00
4 20 No
Supplying fire fighting R.R.L. Hose pipe,
63mm dia,15m in length, fitted with necessary
accessories complete as per specification no.
FF-FFA/RRL
5423.00
( Rupees Five thousand four
hundred & twenty three only )
1,08,460.00
5 10 No
Supplying Stainless Steel branch Pipe 63 mm
Ø fitted with 20 mm dia detachable hexagonal
nozzle as per specifications No. FF-FFA/NZ
1903.00
( Rupees one thousand nine
hundred & three only )
19,030.00
6 10 No
Supplying and erecting M.S./CRCA cabinet for
housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300
mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4
mm. having front doors with viewing glass (8" x 6") and locking
arrangement with necessary fixing material such as rubber bidding etc.
duly painted in post box red colour.
7846.00
( Rupees Five thousand one
hundred & egight seven only )
78,460.00
7 30 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 80 mm dia
with necessary fittings as per specification No.
FF-PP
937.00
( Rupees Nine hundred & thirty
seven only )
28,110.00
8 495 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 150 mm dia
with necessary fittings as per specification No.
FF-PP
1812.00
( Rupees one thousand eight
hundred & twelve only )
8,96,940.00
9 495 M
Providing coating of Bitumen Paint & 4mm
thick Wrapping as per IS 10221 forunderground 150 mm Ring Main of
Fire
Fighting System.
472.00
(Rupees Four hundred Seventy
Two only)
2,33,640.00
10 2 No
Supplying and installing fire brigade Header of
150 mm Ø, for supplying water in fire tank as
per specification No. FF-FA/FBC
9626.00
( Rupees nine thousand six
hundred & twenty sixonly )
19,252.00
14,74,320.00Sub Total (B) Rs
Page 14 of 60
Item No. Qty Unit Items Rate Amount
1 1 No
Supplying & Installing cast iron double flange
butterfly valve of size 100 mm dia. as per
specification No. FF-VL/BFV
3906.00
( Ruppes Thirty Nine thousand
& six only )
3,906.00
2 3 No
Supplying & Installing cast iron double flange
butterfly valve of size 150 mm dia. as per
specification No. FF-VL/BFV
6022
( Ruppes Six thousand & twenty
two only )
18,066.00
3 1 Supplying and installing double flange NRV of
size 100 mm dia as per specification No. FFVL/NRV
8431.00
( Ruppes Eight thousand Four
Hundred Thirty One only )
8,431.00
4 3 No Supplying and installing double flange NRV of
size 150 mm dia as per specification No. FFVL/NRV
20527.00
(Ruppes Five thousand & thirty
seven only)
61,581.00
5 15 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 100 mm dia
with necessary fittings as per specification No.
FF-PP
1273.00
( Rupees one thousand two
hundred & seventy three only )
19,095.00
6 45 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 150 mm dia
with necessary fittings as per specification No.
FF-PP
1812.00
( Rupees one thousand eight
hundred & twelve only )
81,540.00
7 2 No
Supplying and installing, testing, perfect
aligning and proper leveling and
commissioning of fire service main pump, of
2400 LPM (Litres/min.) at 76 m head
centrifugal type single stage pump, 75 HP, (55
kW) or of suitable HP as per specification No.
FF-MFP/SSC
284762.00
( Rupees Two Lakh Eighty Four
Thousand Seven Hundred Sixty
Two only )
5,69,524.00
8 1 No
Supplying installing, testing, commissioning
of Jockey Pump of 240 LPM at 105 mtr. head 3
ph. 415 A.C., 20 HP (18.5 kW) or of suitable
HP with suitable Stages as per specification No.
FF-MFP/JP
132472.00
( Rupees Two Lakh Eighty Four
Thousand Seven Hundred Sixty
Two only )
1,32,472.00
9 1 No
Supplying and installing Air Vessel of 300 mm
Ø 1.5m in height M.S. tank installed inside
pump house as per specification No. FFFFA/ACT
12115.00
( Rupees twelve thousand one
hundred & fifteen only )
12,115.00
( C ) Pump Room
Page 15 of 60
10 1 No
Supplying and erecting 20/25mm Ø G.M.air
release cock, with necessary G.I. coupling tobe fitted on top of Air
vessel or on wet riser as
per specification No. FF-FFA/ARV
807.00
( Rupees eight hundred & seven
only )
807.00
11 1 No
comprising of automatic switch unit isolators, pressure switches to set
operating pressure, switches rated 500 Volt AC 50 Hz supply for
continuous maximum load and Supply Company's regulations, contacts
of suitable size, internal isolating baffles, terminal boxes for cables
suitably screwed, standard 250 Volts, 15 Watt bayonet cap, indicator
lamps for the respective pumps behind ruby domes suitably protected
against damage, interlocking arrangements as per Fire Brigade
stipulations, auxilary switch/switches to provide warning by lighting of a
lamp and hooters for audible alarm both at pump room and main fire
console, tripping a circuit breaker connecting the electric supply to leave
ample power for Fire Pump, if so required. Auxilary switch to be rated at 5
Amps. 250 Volts AC complete with C.T connected ammeters, volt meters
and selector are to be provided on the panels for each starter and
incoming switch fuse unit including necessary power & control cabling
from panel to respective pumps complete as specified. Note:- Contractor
should submit necessary shop drawing for approval of electrical
consultants before fabricating the panel.
135000.00
( Rupees One lakh thirty five
thosandonly )
1,35,000.00
12 5 No
Supplying and installing pressure gauge of 100
mm Ø., 0-300 PSI or 0-14 kg per cm square
fitted with 12/15 mm Ø. pad cock valve, and
G.I. pipe, elbow etc. as per requirement in an
approved manner as per specification No. FFFFA/PG
770.00
( Rupees Seven hundred &
seventy only )
3,850.00
13 4 No
Supplying and installing DANFOSS make
pressure switch with 12/15 mm Ø isolation
valve, G.I. nipple, elbow etc. in an approved
manner as per specification No. FF-FFA/PS
1816.00
( Rupees one thousand eight
hundred & sixteen only )
7,264.00
14 1 No
Stand By Diesel Engine Pumpset :2250 LPM @70 Mtrs. Head with 69
BHP engine 2900 rpm with accessories includes Coupling, Guard, Base
Frame. ( Make Kirloskar ).
562500.00
( Rupees Five lakh sixty two
thousand & five hundred only )5,62,500.00
15 1 No
supply Installation Cloud Based Remote Monitering Systems for
Suitable for both electric and diesel fire pump installations in
Pump room.
165000.00
(Rupees One lakh sixty
five thousand only)
1,65,000.00
Page 16 of 60
17,81,151.00
Item No. Qty Unit Items Rate Amount
1 4 No
Supplying & Installing cast iron double flange
butterfly valve of size 100 mm dia. as per
specification No. FF-VL/BFV
3906.00
( Ruppes Thirty Nine thousand
& six only )
15,624.00
2 2 No
Supplying & Installing cast iron double flange
butterfly valve of size 150 mm dia. as per
specification No. FF-VL/BFV
6022
( Ruppes Six thousand & twenty
two only )
12,044.00
3 390 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 25 mm dia
with necessary fittings as per specification No.
FF-PP
320.00
(Rupees Three Hundred Twenty
only)
1,24,800.00
4 95 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 50 mm dia
with necessary fittings as per specification No.
FF-PP
589.00
(Rupees Five Hundred Eighty
Nine only )
55,955.00
5 30 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 80 mm dia
with necessary fittings as per specification No.
FF-PP
937.00
( Rupees Nine hundred & thirty
seven only )
28,110.00
6 315 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 100 mm dia
with necessary fittings as per specification No.
FF-PP
1273.00
( Rupees one thousand two
hundred & seventy three only )
4,00,995.00
7 195 M
Supplying and installing G.I.pipe above
ground of ‘C’ class ERW of size 150 mm dia
with necessary fittings as per specification No.
FF-PP
1812.00
( Rupees one thousand eight
hundred & twelve only )
3,53,340.00
8 325 No
Supplying and erecting 15 mm (½") dia. NBCM
Body chrome finished quartzoid bulb
sprinkler having 68º C fixed temperature
rating with deflector disc of conventional
construction as per specification No. FF-SPR
449.00
( Rupees four hundred & fourty
nineonly )
1,45,925.00
Sub Total (C) Rs
( D ) Automatic Sprinkler System
Page 17 of 60
9 2 No
Supplying & erecting vane type water flowdetector suitable for
detecting flow of water inwet sprinkler pipe of main line or branch lines of
100 mm dia having following features 1)Visual Switch Activation 2)
Rugged witchAssembly 3) Heavy Duty Alluminium pipe Saddles 4)
Durable Metal Encloser 5) Steel UBolts For Secure Mounting 6) Two
SPDT (Single Pole Double Track ) ynchronisedSwitches 7) Serviceable
Without Draining Pipes
8168.00 ( Rupees Eight
Thousand one hundred Sixty
Eight only )
16,336.00
10 142 M
GI Pipe: 32 mm dia 'C" Class C(Heavy), Plain End ISI Marked
Confirming to IS : 1239 With required fitting. ( Make Apollo / Jindal ).
490.00
( Rupees four hundred & nighty
only )
69,580.00
11 195 M
GI Pipe: 40 mm dia 'C" Class C(Heavy), Plain End ISI Marked
Confirming to IS : 1239 With required fitting. ( Make Apollo / Jindal ).
535.00
( Rupees Five Hundred & thirty
five only )
1,04,325.00
12 115 No
Flexible Drop 1000 mm Flexible Pipe for fall cling sprinkler UL Listed. (
Make Gunllbo / Tyco ).
2150.00
( Rupees Two thousand one
hundred & fifty only )
2,47,250.00
13 1 No
Alarm Gaunge Valve :150 mm diaAlarm Valve is a double seated
clapper check valve with grooved seat design, which ensures positive
water flow for alarm operation and is designed for installation in wet pipe
sprinkler system. UL Lised. ( Make HD fire / Tyco ).
45500.00
( Rupees Fourty five thousand
five hundred only )45,500.00
16,19,784.00
Item No. Qty Unit Items Rate Amount
1 1 NoSupplying and erecting Analog addressable networkable 5loop panel with
battery, each loop capable of taking 99 detectors and devices Makes:
only Honeywell / Apollo/ Raval Notifier
234376.00
( Rupees Two Lakh thirty four
thousand three hundred &
Seventy Six only )
2,34,376.00
2 2 No Supplying and erecting loop card for Analog addressable networkable
system Makes: only Honeywell / Apollo/ Raval Notifier
18360.00
( Rupees eighteen thousand
three hundred & sixty only )
36,720.00
3 16 No Supplying and erecting Loop sounders for Analog adressable
networkable fire alarm panel makes: Honeywell / Apollo/ Raval Notifier
4700.00
( Rupees Four thousand &
seven hundred only )
75,200.00
( E ) Addressable Smoke Detector System
Sub Total (D) Rs
Page 18 of 60
4 1695.76 M
Supplying erecting of 1.5 sqmm 2C multistrand
Cu conductor with PVC insulated with GI
armoured FRLS Polycab cable
115.00
( Rupees one hundred & Fifteen
only )
1,95,012.00
5 4 No
Supplying & Erecting four wire
conventionally single ended reflected type
beam smoke detector with 8 “ receiver . The
range of smoke detector is max 164feet. Honeywell / Apollo/ Raval
Notifier
39928.00
( Rupees thirty nine thousand
nine hundred & twenty eight
only )
1,59,712.00
6 16 No
Supplying and erecting Manual call point with module
makes:Honeywell / Apollo/ Raval Notifier
5223.00
( Rupees Five thousand two
hundred twenty three only )
83,568.00
7 140 No
Supplying and erecting photoelectrical multi sensor
detectors with base makes: Honeywell , Apollo Raval, Notifier
3450.00
(Rupees Three thousand four
hundred & fifty only)
4,83,000.00
12,67,588.00
Item No. Qty Unit Items Rate Amount
1 5 No
SPECIFICATION:- Supply of 46 mm thick Fire Resistant Doors,(2 Hours
Fire Rated) (CBRI APPROVED) Fabricated with 2 nos. of 1.25mm thick
G.I. Sheet with filler (Rockwool) both faces sheet with lock seam joints at
stile edges and internal reinforcement at top, bottom and stile edges.
The Door Frames are manufactured from 1.6mm thick G I Sheet
pressed form to Single Rebate. Fixing arrangement as per BS 476 : Part
22. Provision for fixing and fixtures shall be built in on the door prior to
the supply for all desired Hardware. The door will be finished with powder
coating. (The choice of color shade will be according to client choice.
with Panik bar & Mortise Dead Lock Door Size 1.2 M * 2.4 M
48500.00
(Rupees Fourty eight thousand
five hundred only)
2,42,500.00
2,42,500.00
Item No. Qty Unit Items Rate Amount
Sub Total (E) Rs
( F ) Fire Door
Sub Total Rs
( G ) Maintanance
Page 19 of 60
1 3 Years
Per
annu
m
Operation of CSME (Comprehensive Service Maintenance Contract) (for
8 hours a day / 1 shift ) with minor/ major repairs like pump, servicing,
oling grising , testing & check up clearity, painting etc. for 1 years from
date of handover, Maintanance on skilled trained Labour Provision basis
for all Fire Fighting opration including flexible duty for 1 years form date
of handover as per direction of authority.
360000.00
Per annum
(Rupees Three lakh sixty
thousand only)
10,80,000.00
10,80,000.00
Rs. 87,73,221.00
Sub Total Rs
AMOUNT OF TOTAL FIRE WORKS
Page 20 of 60
Item
No.Qty Unit Item Rate
Rates In
WordsAmount
1 20 Each
Outdoor Box Camera Supply, Installation, testing and commissioning of outdoor box
camera with Video -Compression H.264, Wide Dynamic Range min 120 db, Video
Resolution -1080p HD (1920 X 1280) , Frame Rate- Minimum 60 fps in All
Resolutions, Image Sensor- Minimum 1/2.8” Progressive Scan CCD / CMOS, Lens
Type -Varifocal Lens- 3 to 9 mm, 4X Digital Zoom, Minimum Illumination- Colour-
0.25 lux, B/W- 0.05lux, Image Setting- Compression, Color, Brightness, sharpness,
contrast, White balance, exposure control, backlight compression, Audio -Built in
Microphone or to be given separately Protocol- HTTP, HTTPS, FTP, SMTP, RTSP,
RTP, TCP, UDP, RTCP, DHCP, UPNP, QOS, Security - Password protection, IP
address filtering, User access log, Operating Conditions- 0 to 50 ºC, CCTV camera
housing of Steel / aluminum alloy casting or superior quality with necessary brackets
in stainless steel / allied material and hardware to install the camera, camera housing
in baked enamel, IP66 , IK10 with blower / fan, SD card support of upto 2TB,
Operating Voltage - POE or 24VAC/ 12DC, Compatible- Latest web browser,
Operating humidity 0% to 80% RH, Day Night capability, Forum- ONVIF profile S
conformance, including pole mount adaptor & bracket OR wall mount bracket, with
advance vedio anyalitics such as light distingtion, occupancy, similarity search, line
crossing, field viewing, defoucusing, too dark-light etc., Certification -CE, UL, EN,
IK10, IP66 including ONE YEAR OF ON SITE COMPREHENSIVE ANNUAL
MAINTAINANCE CONTRACT. The Lens & Housing can be manufactored from any
contry. Camera Make (Country Of Origin) - Bosch (Europe), Axis (Europe), Pelco
(America), Infinova (America), Samsung (S. Korea) RA- PCMC-28-1 2016-17
130000Rupees One Lakh Thirty
thousand Only INR 26,00,000.00
2 20 Each
Indoor Dome Camera Supply, Installation, testing and commissioning of indoor dome
camera with Video -Compression H.264, Video Resolution -1080p HD (1920 X 1280)
, Wide Dynamic Range min 120db, Frame Rate- Minimum 60fps in All Resolutions,
Image Sensor- Minimum 1/2.8” Progressive Scan CCD / CMOS, Lens Type -
Varifocal Lens- 3 to 9 mm, 4X Digital Zoom, Minimum Illumination- Colour- 0.25 lux,
B/W- 0.05lux, Image Setting- Compression, Color, Brightness, sharpness, contrast,
White balance, exposure control, backlight10 compression, Audio -Built in
Microphone or to be given separately Protocol- HTTP, HTTPS, FTP, SMTP, RTSP,
RTP, TCP, UDP, RTCP, DHCP, UPNP, QOS, Security - Password protection, IP
address filtering, User access log, Operating Conditions- 0 to 50 ºC, CCTV camera
housing of Steel/ aluminium alloy casting or Superior Quality with necessary brackets
in stainless steel / allied material and hardware to install the camera, camera housing
in baked enamel, IP 66, IK10, SD card support upto 2TB, Operating Voltage - POE or
24VAC/ 12DC, Compatible- Latest web browser, Operating humidity 20% to 80% RH,
Day Night capability, Forum- ONVIF profile S conformance, including pole/ wall
mount, with advance video anyalitics such as light distingtion, occupancy, similarity,
line crossing, field viewing, defoucusing, too dark-light etc., Certification -CE, UL, EN,
IK10, IP66 including ONE YEAR OF ON SITE COMPREHENSIVE ANNUAL
MAINTAINANCE CONTRACT Camera Make (Country Of Origin) - Bosch (Europe),
Axis (Europe), Pelco (America), Infinova (America), Samsung (S. Korea) RA- PCMC-
28-2 2016-17
62000Rupees Sixty Two Thousand
Only INR 12,40,000.00
3 2 Each
Network Video recorder 32 Channel Supply installation, testing and commissioning of
Network Vidio Recorder of 32 channels with min 4 slots for HDD drive, with H.264
and MJEG codec supported with min bandwidth of 120 Mbps for recording, tripple
strims for live viewing, recording and mobile / browser viewing, HDMI and VGA
connection for local Monitor connection, robust, secure operation, rack mount, 4
Trays: 3.5-inch SATA, min 2 USB 2.0, Operating Temperature +10 °C to +35 °C, with
suitable OS, Relative humidity-20 to 85% (non- condensing), video client software
with Live viewing of multiple cameras, Local recording and snapshots, PTZ control
and digital zoom, Playback and export from storage, Motion and forensic search,
Multi-screen grid selection (1, 2X2, 3X3 and 4X4), Sequencing selection, Audio and
volume control, Log-off and help, Task panels for snapshots, favorite view design etc
and Red 5 & HDD Hot swap feature etc compatible with Pune Police City
Surviellance Software etc complete, Certification -CE, UL, EN. including ONE YEAR
OF ON SITE COMPREHENSIVE ANNUAL MAINTAINANCE CONTRACT Make-
Bosch, Axis, Pelco, Samsung RA- PCMC-28-5 2016-17
354002
Rupees Three Lakh Fifty Four
thousand Two
Only
INR 7,08,004.00
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
PCMC - ELECTRICAL WORKS
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B / ABSTRACT
Memorandum showing the items of work to be carried out
SECTION F :- SECURITY SYSTEM WORKS (PART B)
CCTV System
Page 21 of 60
4 3000 Each
Supply and Laying of Gel-Free, Single-Jacket, Single-Armored Single Mode
Cables Single Mode 12 Core OFC Cable, 9micron Single mode, Armored, loose-
tube, CST armour,Dry core fiber cable, Fiber type 9/ 125, Telcordia's GR-20
and ITU-T 652.D Compliance, No. of cores 6/12/24, Cable Construction
BELLCORE GR 20 / IEC 794-1, Attenuation @1310nm < = 0.35 dB/Km /
@1550nm < = 0.20 dB/Km , Coating / Cladding non-circularity <= 12
microns ,Zero Dispersion Slope <= 0.088 ps / sqnm- km , Max (chromatic)
dispersion <3.5 ps/nm-km @1285-1330 nm / <18.5 ps/nm- km @1550 nm,
Tensile rating Short-Term - 2700N & Long-Term – 890N , Operating
Temperature -40 Degree C to +70 Degree C, Armor Corrugated Steel tape
Armor, Outer Colour Black, Cable jacket MDPE, Outer jacket MDPE, anti -
termite, anti - rodent suitable for direct burial application. Secondary Buffer
Material Dry core Loose Tube. Outer Diameter 12.1 mm , Min Bend 121 mm
Weight 129 Kg/Km (Approx), Marking Identification marking at regular intervals
of 1 meter ONE YEAR OF ON SITE COMPREHENSIVE ANNUAL
MAINTAINANCE CONTRACT Make - Corning, Polycab, Finolex, Legrand,
Systimax
89Rupees Eighty Nine Only
INR 2,67,000/- (Rupees Two Lakh and
Sixty Seven Thousand)
5 6 Each
Supply installation, testing and commissioning of Surveillance grade 4 TB hard disk, compatible with NVR, interface SATA 6 Gb/s, 64 Mb Cache, Operating
temp 0ºC to 70ºC, storage temperature -40ºC to 70ºC Including ONE YEAR OF
ON SITE COMPREHENSIVE ANNUAL MAINTAINANCE CONTRACT Make-
Segate, Western digital, Samsung
8800Rupees Eight Thousand Eight
hundred Only
INR 52,800/- (Rupees Fifty Two Thousand
and Eight Hundred)
6 2 Each
Supply, Installation, testing and commissioning of 24 Ports Managable switch, Stackable Layer 3 Gigabit SFP Swtich, with 4 x 1Gbps Copper Modules 6 x 1
Gbps Single Mode SFP Modules, with remaining 14 vacant slots for future
upgradeabilit, separate slots for stacking with minimum 1 in-built AC power
supply with provision for redundant power supply, Operating temperature : 0° to
40°C, Rapid Ring protection / Resiliency technology soupport, convergence of
Sub 50ms, DDM Support– Optical digital diagnostic monitoring as per SFF –
8472 or equivalent standards. UL, cUL, TUV & ROHS compatibility, IPv4 & IPv6
Standards complete Including ONE YEAR OF ON SITE COMPREHENSIVE
ANNUAL MAINTAINANCE CONTRACT Make- Allied Telesis, Moxa, Cisco, HP,
Junipar
295000Rupees Two Lakh Ninety Five
thousand Only
INR 5,90,000/- (Rupees Five Lakh and
Ninety Thousand)
7 4 Each
Supply, installation, testing and commissioning of 8/ 10 Ports Layer 2 Managable Switch, Gigabit PoE+ Switch, minimum 8 x 1Gbps Copper PoE
Modules loaded with 2 x 1 Gbps Single Mode SFP Modules, minimum 1 in-built
AC power supply with POE budget of minimum 120 watts, Operating
temperature : 0° to 50°C, support Rapid Ring protection / Resiliency technology
providing the convergence of Sub 50ms, DDM – Optical digital diagnostic
monitoring support as per SFF – 8472 or equivalent standards, UL, cUL, TUV
& ROHS compatibility with IPv4 & IPv6 Standards complete Including
ONE YEAR OF ON SITE COMPREHENSIVE ANNUAL MAINTAINANCE
CONTRACT Make- Allied Telesis, Moxa, Cisco, HP, Junipar
78500
Rupees Seventy Eight Thousand
Five hundred
Only
INR 3,14,000/- (Rupees Three Lakh
and Fourteen
Thousand)
8 6 Each
Supply, installation, testing and commissioning of 1000 Mbps SFP Module for Level 2 Managable Switch including ONE YEAR OF ON SITE
COMPREHENSIVE ANNUAL MAINTAINANCE CONTRACT Make- Allied
Telesis, Cisco, Extreme, Juniper, Moxa16000
Rupees Sixteen Thousand Only
INR 96,000/- (Rupees Ninety Six Thousand)
9 2 Each
Supplying, installing, testing and commissioning of 49" LED Full HD TV, Commercial series model for 24 X 7 working condition, capable of connecting to
the client PC, USB port, HDMI port, AV IN, with wall mount and table mount
stand and accessories with 1 years guaranty. Make - Sony, LG & Samsung 21-6-
5 ( CCTV and allied accessories( 2015 - 2016 ) )Completed
65025
Rupees Sixty Five Thousand
Twenty Five
Only
INR 1,30,050/- (Rupees One Lakh
Thirty Thousand and
Fifty)
10 15 Each
Outdoor IR illuminator Supply installation, testing and commissioning of 30 mtr or better identification range Outdoor IR illuminator, adjustable infrared power,
850 nm wavelength, Horizontal field of view 15 mtr at 30 mtr or better, power
supply etc Including One year guarantee Make - Bosch, Raytech 21-6-17 (
CCTV and allied accessories( 2015 - 2016 ) )Completed
24300
Rupees Twenty Four Thousand
Three hundred
Only
INR 3,64,500/- (Rupees Three Lakh
Sixty Four Thousand
and Five Hundred)
11 5 Each
Providing & erecting 6.2 m high Hot Dip galvanised as per specification BSEN ISO 1461, OCTAGONAL pole for CCTV with 1 mtr Bracket with bottom
Dia of 130 mm A/F, Top Dia of 70 mm, Base Plate of 275x275x16 mm /
290x290x16 mm, Sheet Thickness 3 mm, Each section shall be fabricated out
of individual plates duly folded and welded. There shall be only one longitudinal
seam weld per section. Hot dip internally and externally having uniform
thickness of 85 microns for bottom section and 65 microns for top and middle
section, Max. Dynamic loading to withstand Max. Wind pressure As per IS 875
part 3. The welding connection of the base flange shall be fully developed to the
strength of the entire section. The base flange shall be provided with
supplementary gussets between the bolt- holes to ensure elimination of helical
stress concentration.Erected on Provided Cement Concrete Foundation with
Foundation Bolts M20x850mm. with Inbuilt cable junction box with connection
Plate & terminals R,Y,G & B. complete with all provided earthing
& connections. with 1 no/2 no 6 Amp 230 V MCB,s
13680
Rupees Thirteen Thousand Six
hundred Eighty
Only
INR 68,400/- (Rupees Sixty Eight Thousand
and Four Hundred)
Page 22 of 60
12 5 Each
Supplying, installation, testing and commissioning of 9U Wall Mount Rack
(Dimension-600WX9UX500D mm) with front sheet steel glass door to and
bottom cover with cable entry provision, integrated side walls, One pair of
19" angles with wall Mounting provision captive hardware packet 0 20
Pack, 230 V AC, 90CFM, with one meter long cable, 19" Mountable
socket strip with 6 numbers of 5Amp universal sockets, with 2 Mtr long power
cord, One U 19" horizontal cable manager with One year guarantee
Completed
12200Rupees Twelve Thousand Two
hundred Only
INR 61,000/- (Rupees Sixty One Thousand)
13 25 Each
Supplying and erecting ISI mark flush type shockproof plug socket 6 pin 6A and 16A with switch 16A combined unit erected on Filled polypropylene ISI marked
(IS:14772-2000) board or double wooden block / 3mm thick hylam sheet / 4mm
thickplywood pasted with 1.5 mm thick sunmica with S M screws and duly
connected.
137Rupees One hundred Thirty
Seven Only
INR 3,425/- (Rupees Three Thousand Four
Hundred and Twenty
Five)
14 30 MtrPoint wiring for light/fan/bell in 20 mm rigid PVC conduit with 1.5 sq.mm (2+1E) FR grade copper wire,flush type switch, earthing and required accessaries as
per pecification No: WG-PW/SW
501Rupees Five hundred One
Only INR 15,030.00
15 3000 MtrSupplying and fixing Cat-6 LSZH cable suitable for LAN / WAN as per specification in approved manner 60
Rupees Sixty Only
INR 1,80,000/- (Rupees One Lakh and
Eighty Thousand)
16 20 Each
Supplying and fixing 3 meter length, UTP Patch cord of Cat 6 type in position as per
specification No. WG-COC/PC357
Rupees Three
hundred Fifty
Seven Only
INR 7,140/- (Rupees
Seven Thousand One
Hundred and Forty)
17 2 Each
Supplying and plugging FRLS duplex 3 meter length, Fibre Patch cord LC-SC MM(50)
OM3 LSZH DUPLEX complete as per specification No. WG-COC/FPC2817
Rupees Two Thousand Eight
hundred
Seventeen Only
INR 5,634/- (Rupees Five Thousand Six
Hundred and Thirty
Four)
18 4 Each
Supplying and fixing Tool-less Information Outlet (Ethernet) flush/surface type inposition as per specification no. WG-NAS/IO
474Rupees Four hundred Seventy
Four Only
INR 1,896/- (Rupees One Thousand Eight
Hundred and Ninety
Six)
19 2 Each
Supplying and fixing 24 port Patch Panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP
11229
Rupees Eleven Thousand Two
hundred Twenty
Nine Only
INR 22,458/- (Rupees Twenty Two Thousand
Four Hundred and Fifty
Eight)
20 2 Each
Supplying and fixing Wall Mount 12 Ports, Light guide unloaded Interconnect Unit with
adapter Panel as per specification in approved manner4511
Rupees Four Thousand Five
hundred Eleven
Only
INR 9,022/- (Rupees Nine Thousand and
Twenty Two)
21 3000 Mtr
Supplying & erecting mains with 2x2.5 sq.mm.and earth wire 1.5 sq.mm FR PVC
copper wire, in rigid PVC conduit min. 20mm dia, as per specification No: WG-
MA/PC, para no. 1.4.1146
Rupees One hundred Forty
Six Only
INR 4,38,000/- (Rupees Four Lakh
and Thirty Eight
Thousand)
22 2 Each
Supplying & erecting On line UPS pure sine wave of 3 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins battery
backup, as per specification No. AP-UPS72643
Rupees Seventy Two Thousand
Six hundred
Forty Three Only
INR 1,45,286.00
23 2 Each
Providing, erecting & commissioning RCCB only of electro magnetic type with 30/100/300 mA sensitivity and having capacity of 40A 2 pole complete as per
specification No. SWRCCB/ RCCB2435
Rupees Two
Thousand Four
hundred Thirty
Five Only
INR 4,870/- (Rupees Four Thousand Eight
Hundred and Seventy)
24 1000 KG
Providing and fixing sheet metal work in CRCA sheet with fabrication of boxes panel
boards etc. including cutting,bending, drilling, welding, rivetting etc. treated with
anti-rust treament and duly power coated or painted with one coat of red lead
paint and 2 coats of enamel paint as directed.
219Rupees Two hundred
Nineteen Only
INR 2,19,000/- (Rupees Two Lakh and
Nineteen Thousand)
25 976.888 KG
Supplying and erecting Iron, sheet metal work consisting of CRCA Sheets, Various
sections of iron, Plates, Chequered Plates, Rods, Bars, MS pipes, etc. for panel
board or any other purposes complete with bending, cutting, drilling and welding
complete erected at the position with necessary materials duly painted with one
coat of red oxide and two coats of enamel paint to match the switchgears or as
per directions by the authority
135Rupees One hundred Thirty
Five Only INR 1,31,879.88
26 10 Each
Supplying, installtion & marking of Surge arrestor/ Surge Protection Device at the sub
main distribution board after the incoming breaker of Type 2 conforming to IEC
61643- II tested for Imax 40 kA for Three Phase & Neutral as per specification
no. CP-SPD
6855
Rupees Six Thousand Eight
hundred Fifty
Five Only
INR 68,550.00
Page 23 of 60
27 100 Each
Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with
coupling collar of standard thickness at required depth up to 90 cm below road /
ground surface, for enclosing provided cable & necessary back filling with light
ramming to make the road/ground surface as it was (Except bitumen carpet).694
Rupees Six hundred Ninety
Four Only
INR 69,400/- (Rupees Sixty Nine Thousand
and Four Hundred)
28 300 Each
Supplying and laying (including excavation) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road
surface, to required depth complete. 226Rupees Two hundred Twenty
Six Only
INR 67,800/- (Rupees Sixty Seven Thousand
and Eight Hundred)
29 5 m3
Providing cement concrete for foundation or for concrete filling in 1:3:6 ratio with 20 to 25 mm. stone metal duly plastered with necessary curing for pole muffing
or any other purposes.4837
Rupees Four Thousand Eight
hundred Thirty
Seven Only
INR 24,185/- (Rupees Twenty Four Thousand
One Hundred and
Eighty Five)
30 10 Each
Supplying and erecting clamps, made out of 25x3mm, copper strips to be fixed to tubular bus for connecting the bare copper wire to other equipment, with
brass nuts bolts of suitable dia. 220Rupees Two hundred Twenty
Only
INR 2,200/- (Rupees Two Thousand and
Two Hundred)
31 10 Each
Providing earthing with Galvanized cast iron earth plate size 60 x 60 x 0.6 cm
complete with all materials, testing & recording the results as per specification
No. EA-EP 4750
Rupees Four Thousand
Seven hundred
Fifty Only
INR 47,500.00
INR 79,55,030
Item
No.Qty Unit Item Rate Amount
1 1 Each
Supply, Installation, Testing & Commissiong of
9 Way MCU, 12X Zoom, Bluetooth, WiFi with Audio Conference Phone. - Supports
any SIP platform and any Android app and
can bridge calls from Android apps into SIP conference. - Built-in Bluetooth for use
with Bluetooth speakers/microphones, keyboards, data exchange, etc. - Support for
3 screens (3 HDMI outputs) - A powerful 12x optical zoom offers robust video clarity
- Dual-band WiFi support offers mobility Local & far-end controllable PTZ camera
with wideangle lens
457770
Rupees Four
Lakh Fifty Seven
thousand Seven
hundred Seventy
Only
INR 4,57,770/- (Rupees
Four Lakh Fifty Seven
Thousand Seven
Hundred and seventy)
2 3 Each Supply, Installation, Testing & Commissiong of HDMI Cable 15 mtr patch 11113
Rupees Eleven
Thousand One
hundred Thirteen
Only
INR 33,339/- (Rupees
Thirty Three Thousand
Three Hundred and
Thirty Nine)
INR 4,91,109
Item
No.Qty Unit Item Rate Amount
1 4EAC
H
Supply, Installation, Testing & Commissiong of Hand held metal detector with builtin
battery charger7422
Rupees Seven
Thousand Four
hundred Twenty
Two Only
INR 29,688/- (Rupees
Twenty Nine Thousand
Six Hundred and Eighty
Eight)
2 1EAC
H
Supply, installation and commissioning of Four zone Door frame metal detector with
pinhole camera& text overlay synchronized with the video image & real time storage
micro controller based with standalone DVR, inluding 500GB HDD, 16.5" Monitor,
inbuilt control unit & walk / stop indicator with ABS coated panel, infra red sensor &
counter in / out including battery backup 21-5-12 Telecom 2012-13
208768
Rupees Two
Lakh Eight
thousand Seven
hundred Sixty
Eight Only
INR 2,08,768/- (Rupees
Two Lakh Eight
Thousand Seven
Hundred and Sixty Eight)
3 1EAC
H
Supply, Installation, Testing & Commissiong of Mirror for detecting bomb under
vehicle.13511
Rupees Thirteen
Thousand Five
hundred Eleven
Only
INR 13,511/- (Rupees
Thirteen thousand Five
hundred and eleven)
INR 2,51,967/-
Item
No.Qty Unit Item Rate Amount
Total Inclusive of all taxes
Audio Video Conference System OFFER
Total Inclusive of all taxes
OFER FOR METAL DETECTOR & BOMB DETECTOR SYSTEMS
Total Inclusive of all taxes
LED Screen OFFER
Page 24 of 60
1 4 Each
Supply, Installation, Testing & Commissiong of Wall Mount Outdoor LED Display alongwith required Fabrication work, operating Parameter Pixel Pitch 6
mm, in 16 X9 format resolution ratio, minimum 125 sq ft., LED Type - SMD,
Brightness min 5500 cd/m² . Viewing angle H: 140°; V:120°, Pixel density
minimum 20000 pix/m² with P6 Pitch pitch, Recommended viewing distance
≥6.7M Module size 200mm×400mm, Cabinet size, m×H1200mm×D115mm
Weight 40.5 kg/panel, Area 1.44 m² Material Epoxy Paint Coated Aluminum,
Aspect ratio 1:1 Ingress protection IP65/IP54. Operating Temperature/Humidity -
20℃~+50℃/10~90%RH Storage Temperature/Humidity -
30℃~+60℃/10~90%RH. Maintenance - Front / rear Optional.Color 4.4 trillion.
Brightness control - Manual/Automatic. Contrast ratio 2000:1. Video frame rate
50/60 Hz. Rate refresh ≥1000 Hz. Input voltage 100~240VAC. Input power
frequency 47~63Hz. Input power <max> 670W/m2. Input power <typical> 224W
/m2. LED Life Time ≥100,000 Hours.Input signal RF,S-VIDEO,RGBHV,YUV,YC
& COMPOSITION,etc. Input File format - JPEG, MPEG, SWF,GIF,
DAT.Certification from CE, BIS, FCC / UL from OEM.
2536045
Rupees Twenty Five
Lakh Thirty Six
thousand Forty Five
Only
INR 1,01,44,180/- (Rupees
One Crore One Lacks Forty
Four Thousand One
Hundread And Eighty Only )
INR 1,01,44,180/-
Item
No.Qty Unit Item Rate Amount
1 1 EachSupplying, installing, testing & commissioning Digital (Hybrid) type EPABX of 4 x 12(2 Digital+10 Analogue) extension complete.
33902Rupees Thirty Three
Thousand Nine
hundred Two Only
INR 33,902/- (Rupees
Thirty Three Thousand
Nine Hundred and Two)
2 15 Each
Supplying, installing, testing & commissioning approved type Push button telephone instrument desk top/wall mount with caller ID unit as per specification
in approved manner
960Rupees Nine
hundred Sixty Only
INR 14,400/- (Rupees
Fourteen Thousand and
Four Hundred)
3 1 EachSupplying, erecting & commissioning Main Distribution Frame (MDF) Box 50x50 pairs as per specification No. WG-TW
2045Rupees Two
Thousand Forty Five
Only
INR 2,045/- (Rupees
Two Thousand and Forty
Five)
4 3 EachSupplying, erecting & commissioning Krone module of 10 pairs as per specification No. WG-TW
350Rupees Three
hundred Fifty Only
INR 1,050/- (Rupees
One Thousand and Fifty)
5 2 EachSupplying & erecting Over Voltage protection Magazine suitable for 10 pair as per specification No. WG-TW
364Rupees Three
hundred Sixty Four
Only
INR 728/- (Rupees
Seven Hundred and
Twenty Eight)
6 500 MtrSupplying & erecting Jelly filled armoured telephone cable 10 pair with 0.5 mm dia. Laid in provided trench asper specification No. WGTW
142Rupees One
hundred Forty Two
Only
INR 71,000/- (Rupees
Seventy One Thousand)
7 200 MtrSupplying & erecting telephone cable 2 pair with 0.5 mm dia. laid in provided PVC casing / conduit asper specification No. WG-TW
23Rupees Twenty
Three Only
INR 4,600/- (Rupees
Four Thousand and Six
Hundred)
8 100 MtrSupplying & erecting Jumper wire with 0.5 mm dia as per pecification No. WG-TW
20Rupees Twenty
Only
INR 2,000/- (Rupees
Two Thousand)
9 200 Mtr
Supplying and erecting PVC trunking (PVC casing-n-capping) of size 20 mm with accessories on wall/ceiling as per specification
No: WG-MA/CON, para no. 1.1.2
40 Rupees Forty OnlyINR 8,000/- (Rupees
Eight Thousand)
INR 137,725/-
Item
No.Qty Unit Item Rate Amount
1 12 Each
First Year Maintenance of CCTV System / Fire Alarm System / Audio-Video
Conference System / Metal Detector System / Baggage Scanner System / Outdoor
LED Display Screen / EPABX System - monthly. (Minor Maintenance to be covered
for CCTV - a) Change in angle of
Camera's. b) Blurring of Image. c) Connection Issues. d) IP reset of Camera's.
Audio-Video Conference System - a) Connection Issues. b) Programming Issues.
Metal Detector System - a) Connection Issues. b) Battery Issues.
Outdoor LED Display Screen - a) Programming Issue. b) Connection Issue. c) Video
Output Issue. EPABX
System - a) Connection Issue. b) Programming Issue. c) Krone Box Malfunction
Issue.
Emergency Call for any of above system will be attended in 24 hours.
30240.00
Rupees Thirty
Thousand Two
hundred Forty
Only
INR 3,62,880/- (Rupees
Three Lakh Sixty Two
Thousand Eight Hundred
and Eighty)
2 12 Each
Second Year Maintenance of CCTV System / Fire Alarm System / Audio-Video
Conference System / Metal Detector System / Baggage Scanner System / Outdoor
LED Display Screen / EPABX System - monthly. (Minor Maintenance to be covered
for CCTV - a) Change in angle of
Camera's. b) Blurring of Image. c) Connection Issues. d) IP reset of Camera's.
Audio-Video Conference System - a) Connection Issues. b) Programming Issues.
Metal Detector System - a) Connection Issues. b) Battery Issues.
Outdoor LED Display Screen - a) Programming Issue. b) Connection Issue. c) Video
Output Issue. EPABX
System - a) Connection Issue. b) Programming Issue. c) Krone Box Malfunction
Issue.
Emergency Call for any of above system will be attended in 24 hours.
34776.00
Rupees Thirty
Four Thousand
Seven hundred
Seventy Six Only
INR 4,17,312/- (Rupees
Four Lakh Seventeen
Thousand Three
Hundred and Twelve)
Total Inclusive of all taxes
Total Inclusive of all taxes
Intercom Offer
Non - Comprehensive Annual Maintanance Charge
Page 25 of 60
3 12 Each
Third Year Maintenance of CCTV System / Fire Alarm System / Audio-Video
Conference System / Metal Detector System / Baggage Scanner System / Outdoor
LED Display Screen / EPABX System - monthly. (Minor Maintenance to be covered
for CCTV - a) Change in angle of
Camera's. b) Blurring of Image. c) Connection Issues. d) IP reset of Camera's.
Audio-Video Conference System - a) Connection Issues. b) Programming Issues.
Metal Detector System - a) Connection Issues. b) Battery Issues.
Outdoor LED Display Screen - a) Programming Issue. b) Connection Issue. c) Video
Output Issue. EPABX
System - a) Connection Issue. b) Programming Issue. c) Krone Box Malfunction
Issue.
Emergency Call for any of above system will be attended in 24 hours.
39992.00
Rupees Thirty
Nine Thousand
Nine hundred
Ninety Two Only
INR 4,79,904/- (Rupees
Four Lakhs Seventy
Nine Thousand Nine
Hundred and Four only)
12,60,096.00INR
RS 20240107.00
Total Inclusive of all taxes
TOTAL
Rupees Two Crore Two Lakh Forty thousand One hundred Seven Only
Page 26 of 60
Item No.
Qty Unit DISCRIPTION RATE RATE IN WORDS
Net
Amount
Rate Rs.
A AIR CONDITIONING & AIR HANDLING SYSTEM - HIGH SIDE
Supply, Installation, testing & commissioning of Air handling units in recirculatory configuration with 24G (0.64mm) preplasticised G.I. outer skin and 22G (0.8mm) plain G.I. inner skin with 36kg/m3
density PIR insulation having thickness 23±2 mm in double skin construction as per air flow
daigrams & specifications with following accessories. Thermal break profile at corners and at
joints for double skin air handling units alongwith internal covings.DX cooling coil shall be of copper
tubes with aluminium fins and 4 / 6 rows deep suitable for operation.Inlet and outlet connection of
chilled water shall be on same side.Centrifgal type fans with backward curved impellers. Blower
and motor assembly shall be mounted on common base frame with anti vibration mounting
pads.Fresh Air Filters, EU - 4 Fire retardant flexible canvas connection and cushy foot mounting
for fan Unit shall be provided with flanges and low leakage extruded aluminium volume control
dampers with positive locking arrangement and percent opening gradations on supply side, return
side, fresh air side and purge side in loose condition.
1 2
Each
Supply, Installation, testing & commissioning of Set - 1 AHU-01 & AHU-02 For main HallCapacity : 14000 cfm 3100 F.A CFM, 40mm S.P., 10 HP, 38.5 TR, 6 Row Dx coil AHU Sections
: R.A / F.A + 10MIC-EU-4 + DX Cooling coil + S.S. Drain pan + Heater sect + Fan & motor 6,95,697
Rupees Six Lakh Ninety Five
thousand Six
hundred Ninety
Seven Only
13,91,394
2 2
Each
Supply, Installation, testing & commissioning of Set - 2 AHU-03 & AHU-04 For Setting area bellow Balcany & Upper Balcony
Capacity : 9500 cfm 950 F.A CFM, 40mm S.P., 7.50 HP, 24 TR, 6 Row Dx coil AHU Sections :
R.A / F.A + 10MIC-EU-4 + DX Cooling coil + S.S. Drain pan + Heater sect + Fan & motor
4,74,163
Rupees Four Lakh Seventy Four
thousand One
hundred Sixty
Three Only
9,48,326
3 2
Each
Supply, Installation, testing & commissioning of Set - 3 AHU-05 & AHU-06 for stageCapacity : 5000 cfm 500 F.A CFM, 40mm S.P., 5.00 HP, 10 TR, 6 Row Dx coil AHU Sections :
R.A / F.A + 10MIC-EU-4 + DX Cooling coil + S.S. Drain pan + Heater sect + Fan & motor
2,53,747
Rupees Two Lakh Fifty Three
thousand Seven
hundred Forty
Seven Only
5,07,494
VRF Condensing Units of following actual capacities for Pune
Supply, Installation, testing & commissioning of Supply of Mitsubishi Electric make CITY MULTI-
VRF units complete with fully Inverter driven scroll compressor, air cooled condenser with Inverter
driven varibale speed fan motor having interconnected control wiring and refrigerant piping
housed in compact housing duly powder coated body.
4 6 Each OUT DOOR UNIT : 20 HP ( For set 1 and 2) 5,67,491
Rupees Five Lakh Sixty Seven
thousand Four
hundred Ninety One
Only
34,04,946
5 4 Each OUT DOOR UNIT : 10 HP ( For Set 1 and 2) 2,83,745
Rupees Two Lakh Eighty Three
thousand Seven
hundred Forty Five
Only
11,34,980
6 2 Each OUT DOOR UNIT : 12 HP ( For Set 3) 3,24,280
Rupees Three Lakh Twenty Four
thousand Two
hundred Eighty
Only
6,48,560
Supply, Installation, testing & commissioning of SET No. - 4 for GREEN ROOM AREA
7 5 Each INVERTER TYPE SPLIT HI WALL - 2.0 TR 73,300 Rupees Seventy Three Thousand
Three hundred Only
3,66,500
Supply, Installation, testing & commissioning of Accessories:
8 6 Each Corded Remote- AHU System 15,483
Rupees Fifteen Thousand Four
hundred Eighty
Three Only
92,898
9 1 Each Central remote controller 1,26,702
Rupees One Lakh Twenty Six
thousand Seven
hundred Two Only
1,26,702
10 12 Each LEV KIT FOR AHU WITH ODU 88,152
Rupees Eighty Eight Thousand
One hundred Fifty
Two Only
10,57,824
11 186 K.G. Supplying and charging of oil and freon refrigerant R-410 2,284
Rupees Two Thousand Two
hundred Eighty
Four Only
4,24,824
12 88 Each Ribed Rubber pads for smooth operation . 814 Rupees Eight hundred Fourteen
Only
71,632
TOTAL OF " A " - AIR CONDITIONING SYSTEM 1,01,76,080
BSupply, Installation, testing & commissioning of LOW SIDE - AIR HANDLING SYSTEM -
AHU , DUCTABLE & HI-WALL UNITS
13 6 Each Canvaas Connection for AHU's 4,014 Rupees Four Thousand Fourteen
Only
24,084
SCHEDULE B / ABSTRACT
PCMC - ELECTRICAL WORK
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
Memorandum showing the items of work to be carried out
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION C :- HVAC WORKS (PART B)
Page 27 of 60
14 6 Each
Supply, Installation, testing & commissioning of AHU Control panel of AC Plant as per direction of
authority. Panel to have incomer isolator 32 A, DOL starter, RYB indications, voltmeter, ammeter
etc., ON / OFF PBs, transformer & supply arrangement for thermostate, auxilliary contactor to
receive signal from remote panel etc.
44,880 Rupees Forty Four Thousand Eight
hundred Eighty
Only
2,69,280
15 60 RMT
Supply, Installation, testing & commissioning of Power Cabling between Star delta panel to AHU Motor and Out door panel to AHU Panel :
4 c x 10 sqmm.Armoured Solid Copper conductor wires
Supplying, erecting & terminating PVC armoured cable 4
core 10 sq mm copper conductor continuous 5.48 sq
mm (12 SWG) G.I. earth wire complete erected with glands
& lugs, on wall/ TRusses/pole or laid in provided TRench/ pipe
as per specification no. CB-LT/CU ( Concider 10 mtrs each)
619
Rupees Six hundred Nineteen
Only
37,140
16 6 Each
Supply, Installation, testing & commissioning of floor mounting type powder coated L.T main cubical type conTRol Panel with DIGITAL MULTY FUCTION METER and fabricated out of 16
SWG CRCA sheet, dust and vermin proof, hinged doors for individual switch gears compartment,
cable alley, separate busbar chambers, provision for earth termination, knock outs for incoming
and outgoing cables and conduits, 4 strip aluminum busbar of 200 amps capacity for phase and
natural with color code heat shrinkable sleeves, connector epoxy insulators, grommets, all
interconnections with suitable size copper conductor single core sTRanded cable with lugs.This
panel Includes Main Incommer to each Set ( Total 6 sets) of system which includes 4 pole Main
incomer MCCB 200 AMPS(1 Nos) + 4 Pole ELCB 63 AMPS ( 3 Nos) + For AHU 4 pole MCCB 40
AMPS ( 1 Nos)
58,957
Rupees Fifty Eight Thousand Nine
hundred Fifty
Seven Only
3,53,742
Supply, Installation, testing & commissioning of Refrigeration piping:
Supply, Installation, testing & commissioning of Refrigeration piping: AS PER VRV / VRF
manufacture's standard practice
Supply, Installation, testing & Commissioning of Refrigeration piping:
Refrigerant piping for a/c units including Copper Soft / Hard pipes, fittings, supports, saddles,
pressure testing, insulation, tagging and evacuation (Minor civil work like brick wall
chasing/partition cutting to be done by a/c conTRactor & markings for major civil work to be
provided by a/c conTRactors). (Quantity shall be measured one way & considering single circuit
per machine. Separate rates/ measurement shall not be considered for suction / liquid pipes /
cables or for multiple circuits). Pressure test certificates jointly signed by conTRactor's and Client
representatives to form a part of scope. Interconnected Refrigeration piping with required 9 mm
THK superlon insulation couverd with black PVC tape of following sizes, -
17 549.9259 RMT VRV /VRF Outdoor to AHU-01 , AHU-02, AHU-03 , AHU-04 , AHU -05, AHU-06 2,079 Rupees Two Thousand Seventy
Nine Only
11,43,296
18 50 RMT Inverter type split hi wall type unit - HW-01 to HW-05(CONCIDER 10 MTRS EACH) 1,362
Rupees One Thousand Three
hundred Sixty Two
Only
68,100
Supply, Installation, testing & commissioning of Drain piping:
Supply, Installation, testing & Commissioning of Condensate Drain piping:
HD-PVC Condenset Drain piping with 6mm thk superlon insulation & couvered with black PVC
tape bfor following sizes, -
19 23.6978 Rmt 25mm dia Suitable For 11 TR. Ductable unit 186 Rupees One hundred Eighty Six
Only
4,408
20 20 Rmt 32 mm dia Suitable for 16.5 TR. Packaged unit 194 Rupees One hundred Ninety
Four Only
3,880
21 45 Rmt 40 mm dia ( Not required ) 179 Rupees One hundred Seventy
Nine Only
8,055
Supply, Installation, testing & commissioning of MS Structural Fabrication
Supply, Installation, testing & Commissioning of MS Structural Fabrication for IDUs & ODUs:
22 18 Each For 6 Nos. of AHU's & 12 NOS. ODU 17,920 Rupees Seventeen Thousand Nine
hundred Twenty
Only
3,22,560
23 1 Each For 5 Nos. of Spilt unit & ODU 12,616
Rupees Twelve Thousand Six
hundred Sixteen
Only
12,616
TOTAL OF " B " - AIR HANDLING SYSTEM 22,47,161
C
Supply, Installation, testing & commissioning of AIR DISTRIBUTION SYSTEM FOR AIR
CONDITIONING & VENTILATION ( SHEET METAL & ALLIED WORKS )
Supply, delivery, Installation & testing of FACTORY/ SITE FABRICATED Galvanised Sheet (GI)
Ducting class VIII with M.S. Angle Flange / TDF flanges turning vanes, with proper duct sealing etc
with RTV duct Sealant, complete with supports ,Pressure tested with aqueous base smoke
generator etc all as per specification
24 1880 Sq.M 24 gauge 896 Rupees Eight hundred Ninety Six
Only
16,84,480
25 450 Sq.M 22 gauge 1,405 Rupees One Thousand Four
hundred Five Only
6,32,250
26 250 Sq.M 20 gauge 1,567
Rupees One Thousand Five
hundred Sixty
Seven Only
3,91,750
Supply, Installation, testing & commissioning of THERMAL INSULATION FOR DUCTING
27 1650 Sq.M
Supply ,Installation of Thermal Insulation of duct with 16 mm thick close cell elastomerics nitrile rubber with one side alu.foil and self adhesive properties & all the joints sealed & finished with self
adhesive tape.& as per technical specifications. for Supply Air Duct
Thermal conductivity : 0.27/Wm K , Density kg/cumt : 28 , Class "O"
1,332 Rupees One Thousand Three
hundred Thirty Two
Only
21,97,800
Page 28 of 60
28 1050 Sq.M
Supply ,Installation of Thermal Insulation of duct with 9 mm thick close cell elastomerics niTRile
rubber " Class O " with self adhesive properties & all the joints sealed & finished with self
adhesive tape.& as per technical specifications. For Return Air Duct
Thermal conductivity : 0.27/Wm K , Density kg/cumt : 28 , Class "O"
738 Rupees Seven hundred Thirty
Eight Only
7,74,900
Supply, Installation, testing & commissioning of DIFFUSERS & GRILLES
29 65 Rmt.Supply, Installation, testing & commissioning of AL powder coated Continues Return Grill with dampers with all side Flanges Grill height 300 mm & as per technical specifications.
2,079 Rupees Two Thousand Seventy
Nine Only
1,35,135.00
30 2 Sq.MSupply, Installation, testing & commissioning of Alu. Consrtuction Fresh Air Grills ( Sizes as perdrawing)
12,186
Rupees Twelve Thousand One
hundred Eighty Six
Only
24,372
31 2 Sq.MSupply,Installation, Testing & Commissioning of Aluminium powder coated Door TRansfer grills with all side flanges of 300 X 150 mm
12,687 Rupees Twelve Thousand Six
hundred Eighty
Seven Only
25,374
32 4 Sq.MSupply, Installation, Testing & Commissioning of AL powder coated Continues Supply Air Grill with dampers with all side Flanges Grill size 900 L x 300H mm & as per technical specifications.
6,236 Rupees Six Thousand Two
hundred Thirty Six
Only
24,944
33 46 Nos.
Supply, Installation, Testing & Commissioning of Aluminium Powder Coated Supply Air Grill with damper.The Grill shall be 600 x 600 mm ( neck size 600 x 600 mm ) Armstrong ceiling type with
step or without step. The Grill sizes as per drawing & as per technical specifications.
5,519 Rupees Five Thousand Five
hundred Nineteen
Only
2,53,874
Supply, Installation, testing & commissioning of ACOUSTIC INSULATION -
34 250 Sq.M
Supply ,Installation Acoustic insulation of duct with 12 MM thick / 16 KG dencity CR-300 rigid board (Fiber Glass) covered with R P Tissue paper & 30 gauge Aluminium perforated Sheet & as per
technical specifications ( For return air Duct )
745 Rupees Seven hundred Forty Five
Only
1,86,250
35 250 Sq.M
Supply,Installation,Testing & Commissioning of PAC / AHU room - Acoustical insulation shall be 50 mm thick 32 Kg/ cum fiber Glass Insulation finished with dimensionally stable Black RP Tissue
facing & 26 G perforated aluminium sheets as specified
1,183 Rupees One Thousand One
hundred Eighty
Three Only
2,95,750
36 750 Sq.M
Supply ,Installation Acoustic insulation of duct with 25 MM thick / 48 KG dencity CR-300 rigid board (Fiber Glass) covered with R P Tissue paper & 30 auge perforated Aluminium Sheet & as
per technical specifications.. ( For Supply Air Duct )
1,090 Rupees One Thousand Ninety
Only
8,17,500
Supply, Installation, testing & commissioning of DAMPERS -
37 15 Sq.M.Supply , Installation, Testing & Commissioning of Duct Damper of GI consTRuction & as per technical specifications..
9,820 Rupees Nine Thousand Eight
hundred Twenty
Only
1,47,300
38 15 Sq.M
Supply, Installation, Testing & Commissioning of galvanized sheet fire damper with limit switch andfusible link (Fusible link melting point 72°C). The damper shall be CBRI approved for 90 minutes
fire rating.
11,268
Rupees Eleven Thousand Two
hundred Sixty Eight
Only
1,69,020
TOTAL OF "C" - AIR DISTRIBUTION SYSTEM 77,60,699
D Supply, Installation, testing & commissioning of VENTILATION-
TOTAL OF "D" - VENTILATION
e 997.0000 kgs Supply, Installation, testing & commissioning of Supporting work ( Mild steel ) 115 Rupees One hundred Fifteen
Only
1,14,655
TOTAL OF " E " - STRUCTURAL SYSTEM 1,14,655
FSupply, Installation, testing & commissioning of ELECTRICAL WORK :
Main Electrical Panel in Electrical scope of supply
Communication / Control Cabling from Indoor unit to Outdoor unit for a/c units with supports,
earthing, terminations including lugs and glands, tagging, continuity test and meggar test.
(Quantity shall be measured one way & considering single circuit. Separate rates/ measurement
shall not be considered for multiple circuits.) Continuity and Meggar test certificates jointly signed
by contractor's and PMC representative to form a part of scope.
39 650 Rmt
Suppy , Installation , Testing & Commissioning of communication cable fromIndoor to Outdoor units
Shealded cable 3C x 1.5 sqmm
308 Rupees Three hundred Eight Only
2,00,200
TOTAL OF " F " - ELECTRICAL SYSTEM 2,00,200
G Dismentling and Mainatanace :
40 1.00 LotDismentling of Total Exisitng Chilled water System I.E.AHU ,Chiller,MS pipe and lied accessories Ducting,Insulation in all resepcts
9,32,198
Rupees Nine Lakh Thirty Two
thousand One
hundred Ninety
Eight Paise Forty
Only
9,32,198
41 3.00PER
ANNUM
Operation - Including of 1st year after handovering + 2 years (for 16 hours a day / 365 days ) with
minor repairs like Wiring work in panel / AC system ,outdoor unit cleaning,Dry Servicing for month
, preventive check up Period : from the date of handing of site. Skilled Labour provision
basis for all AC System . Also to Submitt maintainance report if any on monthly analylis and
reporting to Authority of PCMC.
4,95,600 Rupees Four Lakh Ninety Five
thousand Six
hundred Only
14,86,800
42 1.00PER
ANNUM
Annual comprehensive Maintanance contract for entire Project After one year of warranty period .(
2nd year)
6,99,200
Rupees Six Lakh Ninety Nine
thousand Two
hundred Only
6,99,200
Page 29 of 60
43 1.00PER
ANNUM
Annual comprehensive Maintanance contract for entire Project After one year of warranty period .(
3rd year )
7,90,096
Rupees Seven
Lakh Ninety
thousand Ninety Six
Only
7,90,096
39,08,294
Above offered Prices are Including ( Supply,Installation,testing & commissioning )
with taxes and Duties
2,44,07,089
Rupees Two Crore Forty Four Lakh Seven thousand Eighty Nine Paise Fourteen Only
TOTAL OF " G " - Dismentling and Mainatanace
TOTAL Rs.
Page 30 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
EXTERNAL
A HT CABLES
100.00 Mtr. 1
Supplying , erecting & terminating 3 x 300 sq mm 22 kV, XLPE(E)
armoured cable on wall/ceiling or laid in provided trench / pipe in an
approved manner as per specification No. CB-HT (PWD CSR 2017-
18 7-3-18)
Mtr. 2925.00
Rupees Two
Thousand Nine
hundred Twenty
Five Only
292500.00
60.0 Mtr. 2
Supplying , erecting & terminating 3 x 95 sq mm 22 kV, XLPE(E)
armoured cable on wall/ceiling or laid in provided trench / pipe in an
approved manner as per specification No. CB-HT (PWD CSR
2017-18 7-3-2)
Mtr. 1109.00
Rupees One
Thousand One
hundred Nine
Only
66540.00
3.0 Nos 3
Providing and erecting Heat shrinkable outdoor termination kit for 22
kV ( E ) XLPE HT cable 3x70 to 120 sq mm cable with necessary
material as per specification No. CBJT/HT (PWD CSR 2017-18 7-5-11)
Nos 20082.00
Rupees Twenty
Thousand
Eighty Two Only
60246.00
Sub-total: 419286.00
B HT Panel
1.0Eac
h4
Supplying , erecting, testing & commissioning 22kV, 630A, 16kA/3sec,
3Way Outdoor,Extensible motorised SCADA compatible RMU as per
Electric Supply Co specification consisting of 2Nos. feeder with Load
Break witch and 1No. feeder with VCB. | <2LBS+1VCB+M> as per
specifiaation no. SW-HTS/ RMU SCADA(PWD CSR 2017-18 5-9 25 )
MTR 821023.00
Rupees Eight
Lakh Twenty
One thousand
Twenty Three
Only
821023.00
Memorandum showing the items of work to be carried out
SECTION A :- ELECTRICAL WORKS (PART B)
Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
PCMC - ELECTRICAL WORK
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
SCHEDULE B / ABSTRACT
Project Name
Page 31 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
Sub-total: 821023.00
C Miscellaneous
2.00Eac
h5
Providing printed instruction chart for treating persons suffering from
electric shock, printed in English & Marathi and duly laminated.
(PWD CSR 2017-18 10-2-22)
Each 126.00
Rupees One
hundred Twenty
Six Only
252.00
2.00Eac
h6
Provided pair of duly tested rubber hand gloves as per IS :340715
suitable for working on 22kV supply. (PWD CSR 2017-18 10-2-23) Each 622.00
Rupees Six
hundred Twenty
Two Only
1244.00
4.00Eac
h7
Providing round bottom FIRE Bucket of 9 Litres capacity as per IS :
2546 made out of 24 gauge G.I. sheet with extra handle at bottom
duly painted white inside and red outside with FIRE Mark, on provided
stand/ wall hook. (PWD CSR 2017-18 10-2-24)
Each 775.00
Rupees Seven
hundred
Seventy Five
Only
3100.00
1.00Eac
h8
Providing floor mounting stand for keeping 4 Nos. of FIRE buckets
1500mm in length, 900mm in height frame made out of 30x30x4 mm
angle iron with cross supports for legs, welded with 4 hooks and duly
painted with one coat of red lead and two coats of silver paint. (PWD
CSR 2017-18 10-2-25)
Each 3298.00
Rupees Three
Thousand Two
hundred Ninety
Eight Only
3298.00
4.00Eac
h9
Supplying and erecting Wall hook 225mm projection for keeping fire
buckets made out of 15 mm dia. M.S. Rod grouted in wall to a depth
of minimum 15cms. (PWD CSR 2017-18 10-2-26)
Each 76.00Rupees Seventy
Six Only304.00
2.00Eac
h10
Supplying standard first aid box with necessary antiseptic cream,
medicine for use on wounds due burn, crepe bandage, gauge
bandage, medicated ready to use bandage (Band-aid) adhesive tape
for medicinal use, scissors, anti-septic solution (Savlon or similar) etc.
(All above contents shall be of standard makes) (PWD CSR 2017-18
10-2-27)
Each 765.00
Rupees Seven
hundred Sixty
Five Only
1530.00
2.00Eac
h11
Supplying and fixing PVC Synthetic elastomer electrically insulating
mat with class C insulation conforming to IS: 15652 – 2006 & CPRI
tested having 3mm thickness upto 33 kV (PWD CSR 2017-18 10-2-
32)
Each 7079.00
Rupees Seven
Thousand
Seventy Nine
Only
14158.00
2.00Per
Pair12
Supplying shock proof leather Safety Shoes of Electrical grade of
standard size as IS :11226, 14544 duly tested, with necessary test
certificate from manufacturer. (PWD CSR 2017-18 10-2-33)
Per
Pair1850.00
Rupees One
Thousand Eight
hundred Fifty
Only
3700.00
Page 32 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
2.00Eac
h13
Supplying and erecting D.C.P. type Fire Extinguisher 10 kg capacity
cartridge type with Gun Metal cap 150 gram CO2 gas cartridge,
powder and brackets conforming to IS 2171-1985 and complete
erected with necessary clamps made from 50x6 mm M.S. flat with
nuts & bolts grouted in wall complete. (PWD CSR 2017-18 10-2-35)
Each 4672.00
Rupees Four
Thousand Six
hundred
Seventy Two
Only
9344.00
Sub-total: 36930.00
Page 33 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
E LT Panel
Design, Fabrication, inspection at factory, supply, installation at site,
testing and commissioning of medium voltage (415 volts ), 3 Ph. &
neutral, 50 Hz AC supply, cubicle panel, of 14/16 SWG MS CRCA
sheet 40x40x5mm thick angle iron frame work as per required design
.(Aluminium Bus bar suitable for 600Amp /Sq.inch)
MAIN PCC PANEL
Location :-Near Transformer yard .
INDOOR TYPE
MSEDCL INCOMING SECTION
1000A, 4P, EDO,ACB, 50KA with Microprocessor based , LSING,
Shunt + Aux. contact block : 1 Set
CT 1000A/5A,5VA,CL1.0 :- 3 Nos.
CT 1000A/5A,5VA,CL1.0 :- 3 Nos.(FOR RTPFC )
CBCT 1000A/5A,5VA,CL1.0 :-1 Nos.
Earth fault Realy,240V AC:-1 Nos.
100A TP MCCB with TVSS Class B : 01 Nos.
35 Kvar fixed type capacitor bank with incomer isolator MCCB of 63A
TP+NL 25 KA : 1 Set
Digital Type Multifunction Meter :-1 Nos.
Indicating Lamp 240V AC R/Y/B with control MCB :- 3 Nos .
Indicating Lamp 240V AC ON/OFF/TRIP with control MCB:- 3 Nos .
DG INCOMING SECTION
1000A, 4P, EDO,ACB, MF 50KA with Microprocessor based , LSING,
Shunt + Aux. contact block : 1 Set
CT 1000A/5A,5VA,CL1.0 :- 3 Nos.
CT 1000A/5A,5VA,CL1.0 :- 3 Nos.(FOR RTPFC )
CBCT 1000A/5A,5VA,CL1.0 :-1 Nos.
Earth fault Realy,240V AC:-1 Nos.
100A TP MCCB with TVSS Class B : 01 Nos.
Digital Type Multifunction Meter :-1 Nos.
Indicating Lamp 240V AC R/Y/B with control MCB :- 3 Nos .
Indicating Lamp 240V AC ON/OFF/TRIP with control MCB:- 3 Nos .
BUS-BAR SECTION
Rupees Twelve
Lakh Only141 Set 1200000Set 1200000
Page 34 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
1250A Three Pole with Neutral Link Aluminum Bus-Bar with color
coated heat shrinkable sleeve .
OUTGOING SECTION
500A TP+NL 50KA MCCB with LSI protection, Microprosser Based :-
02 Nos.
400A TP+NL 50KA MCCB with LSI protection, Microprosser Based :-
03 Nos.
315A TP+NL 50KA MCCB with LSI protection, Microprosser Based :-
01 Nos.
200A TP+NL 50KA MCCB with LSI protection, Microprosser Based :-
01 Nos.125A TP+NL 50KA MCCB with LSI protection, Microprosser Based :-
02 Nos.
63A TP+NL 50KA MCCB with LSI protection, Microprosser Based :- 01
Nos.
Only Space Provision for 315A 4P MCCB . 50KA .: - 02 Nos.
170KVAR RTPFC PANELLocation :-IN TRANSFORMER YARD
INDOOR TYPE
MAIN INCOMING SECTION
400A TP+NL 25KA MCCB with LSI protection ,Microprosser Based :-
1 Nos.
CT 400A/5A,5VA,CL1.0 :- 3 Nos.
(0-400A) Ammeter :- 1 Nos
(0-500V) Voltmeter :- 1 Nos
Voltage Selector Switch :- 1 Nos
Ammeter Selector Switch :- 1 Nos
Indicating Lamp 240V AC R/Y/B with control MCB :- 3 Nos .
Indicating Lamp 240V AC ON/OFF/TRIP with control MCB:- 3 Nos .
BUS-BAR SECTION
500A Three Pole with Neutral Link Aluminum Bus-Bar with color coated
heat shrinkable sleeve .
OUTGOING SECTION
Rupees Twelve
Lakh Only
Rupees Three
Lakh Forty Four
thousand Sixty
Four Only
14
1 Set 344064Set15
1 Set
344064
1200000Set 1200000
Page 35 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
25 Kvar 440V AC MPP type Capacitor :-4 Nos
20 Kvar 440V AC MPP type Capacitor :-2 Nos
10 Kvar 440V AC MPP type Capacitor :-2 Nos
5 Kvar 440V AC MPP type Capacitor :-2 Nos
Only Space Provision 5 Kvar 440V AC MPP type Capacitor :-2 Nos
25 Kvar Thyristor Module with heat Sink :- 04 Nos.
20 Kvar Thyristor Module with heat Sink :- 02 Nos.
10 Kvar Thyristor Module with heat Sink :- 02 Nos.
05 Kvar Thyristor Module with heat Sink :- 02 Nos.
Only Space Provision 5 Kvar Thyristor Module with heat Sink :- 2 Nos.
63A HRC FUSE LINK :- 04 Nos
40A HRC FUSE LINK :- 02 Nos
32A HRC FUSE LINK :- 02 Nos
16A HRC FUSE LINK :- 02 Nos
Only Space Provision16A HRC FUSE LINK :- 02 Nos
Push Button Luminous Green with Element :- 12 Nos .
Push Button Luminous Red with Element :- 12 Nos .
25 Kvar 440V AC Detuned reactor 7% detuned :- 04 Nos
20 Kvar 440V AC Detuned reactor 7% detuned :- 02 Nos
10 Kvar 440V AC Detuned reactor 7% detuned :- 02 Nos
05 Kvar 440V AC Detuned reactor 7% detuned :- 02 Nos
Only Space Provision 05 Kvar 440V AC Detuned reactor 7% detuned
:- 02 Nos
Control Section
9A TP 240V AC contactor :- 1 Nos.
12 Stage Microprocessor Based RTPFC Relay :- 1 Nos.
2A SP MCB 10KA :- 3 Nos .
1P, 2 way selector Switch :- 1 Nos
Exhaust Fan 4" :- 6 Nos .
AUDITORIUM MAIN PANELLocation :-IN AUDITORIUM
INDOOR Type
Rupees Three
Lakh Forty Four
thousand Sixty
Four Only
Rupees One
Lakh Seventy
Two thousand
Thirty Two Only
1 Set 344064Set15 344064
17203216Set Set 1720321
Page 36 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
MAIN INCOMING SECTION
315A TP+NL 25KA MCCB with LSI protection Microprosser Based
Type :- 1 Nos.
CT 315A/5A,5VA,CL1.0 :- 3 Nos.
(0-500V) Voltmeter :- 1 Nos
Voltage Selector Switch :- 1 Nos
Indicating Lamp 240V AC R/Y/B with control MCB :- 3 Nos .
Indicating Lamp 240V AC ON/OFF/TRIP with control MCB:- 3 Nos .
BUS-BAR SECTION
400A Three Pole with Neutral Link Aluminum Bus-Bar with color coated
heat shrinkable sleeve .
OUTGOING SECTION
160A TP+NL MCCB 25KA with LSI protection ,Microprosser Based: 1
Nos .
125A TP+NL MCCB 25KA with LSI protection ,Microprosser Based: 2
Nos .
Only Space Provision for 125A TP+NL MCCB 25KA with LSI protection
,Microprosser Based .:-05 Nos.
HVAC MAIN PANELLocation :-IN AUDITORIUM
INDOOR Type
MAIN INCOMING SECTION
500A TP+NL 25KA MCCB with LSI protection ,Microprosser Based
Type :- 1 Nos.
CT 500A/5A,5VA,CL1.0 :- 3 Nos.
(0-500V) Voltmeter :- 1 Nos
Voltage Selector Switch :- 1 Nos
Indicating Lamp 240V AC R/Y/B with control MCB :- 3 Nos .
Indicating Lamp 240V AC ON/OFF/TRIP with control MCB:- 3 Nos .
BUS-BAR SECTION
630A Three Pole with Neutral Link Aluminum Bus-Bar with color coated
heat shrinkable sleeve .
OUTGOING SECTION
Rupees One
Lakh Seventy
Two thousand
Thirty Two Only
Rupees One
Lakh Fifty
thousand Five
hundred Twenty
Eight Only
150528.00
172032
17
16
1 Set
Set Set 1720321
150528Set
Page 37 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
400A TP+NL 25KA MCCB with LSI protection ,Microprosser Based
Type :- 1 Nos.
63A 4P MCB 10KA C-Type : 2 Nos .
40A 4P MCB 10KA C-Type : 4 Nos .
Only Space Provision for 40A 4P MCB . 25KA.:-01 Nos.
AC OUTDOOR UNIT PANELLocation :-ON TERRACE FLOOR
Outdoor Type
MAIN INCOMING SECTION
400A TP+NL 25KA MCCB with LSI protection ,Microprosser Based
Type :- 1 Nos.
CT 400A/5A,5VA,CL1.0 :- 3 Nos.
(0-500V) Voltmeter :- 1 Nos
Voltage Selector Switch :- 1 Nos
Indicating Lamp 240V AC R/Y/B with control MCB :- 3 Nos .
Indicating Lamp 240V AC ON/OFF/TRIP with control MCB:- 3 Nos .
BUS-BAR SECTION
500A Three Pole with Neutral Link Aluminum Bus-Bar with color coated
heat shrinkable sleeve .
OUTGOING SECTION
63A 4P,300mA, RCBO 10KA : 11 Nos .
Only Space Provision for 40A 4P MCB . 25KA.:-03 Nos.
UPS MAIN PANEL Location :- lvl 10.02
Indoor Type
MAIN INCOMING SECTION
160A TP+NL 25KA MCCB with LSI protection ,Microprosser Based
Type :- 1 Nos.
CT 160A/5A,5VA,CL1.0 :- 3 Nos.
(0-500V) Voltmeter :- 1 Nos
Voltage Selector Switch :- 1 Nos
Indicating Lamp 240V AC R/Y/B with control MCB :- 3 Nos .
Rupees One
Lakh Fifty
thousand Five
hundred Twenty
Eight Only
Rupees One
Lakh Twenty
One thousand
Eight hundred
Fifty Six Only
Rupees One
Lakh Fifty Seven
thousand Six
hundred Ninety
Six Only
157696.0019
18
Set
121856.00
150528.00
157696.00
17
1 Set
121856
1 Set
Set Set1
150528Set
Page 38 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
Indicating Lamp 240V AC ON/OFF/TRIP with control MCB:- 3 Nos .
BUS-BAR SECTION
200A Three Pole with Neutral Link Aluminum Bus-Bar with color coated
heat shrinkable sleeve .
OUTGOING SECTION
125A TP+NL 25KA MCCB with LSI protection ,Microprosser Based
Type :- 1 Nos.
100A TP+NL 25KA MCCB with LSI protection ,Microprosser Based
Type :- 1 Nos.
80A TP+NL 25KA MCCB with LSI protection ,Microprosser Based Type
:- 1 Nos.
40A 4P MCB 10KA C-Type : 4 Nos .
Only Space Provision for 125A 4P MCCB . 10KA.:-01 Nos.
Only Space Provision for 40A 4P MCB . 10KA.:-03 Nos.
Sub-total: 2146176.00
F LT CABLES WITH TERMINATION
280.00 Mtr 20
Supplying, erecting & terminating PVC armoured cable 3½ core 300
sq mm aluminium conductor with continuous 12.97 sq mm (8 SWG)
G.I. earth wire complete erected with glands & lugs, on wall/
trusses/pole or laid in provided trench/ pipe as per specification no. CB-
LT/AL. (PWD CSR 2017-18 7-1-31)
Mtr 1613.00
Rupees One
Thousand Six
hundred
Thirteen Only
451640.00
180.00 Mtr 21
Supplying, erecting & terminating PVC armoured cable 1100 V. 3½
core 185 sq mm aluminium conductor with continuous 12.97 sq mm
(8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/
trusses/pole or laid in provided trench/ pipe as per specification no. CB-
LT/AL. (PWD CSR 2017-18 7-1-29)
Mtr 1139.00
Rupees One
Thousand One
hundred Thirty
Nine Only
205020.00
168.00 Mtr 22
Supplying, erecting & terminating PVC armoured cable 3½ core 150
sq mm aluminium conductor with continuous 12.97 sq mm (8 SWG)
G.I. earth wire complete erected with glands & lugs, on wall/
trusses/pole or laid in provided trench/ pipe as per specification no. CB-
LT/AL (PWD CSR 2017-18 7-1-28)
Mtr 931.00
Rupees Nine
hundred Thirty
One Only
156408.00
Rupees One
Lakh Fifty Seven
thousand Six
hundred Ninety
Six Only
157696.0019 Set 157696.001 Set
Page 39 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
160.00 Mtr 23
Supplying, erecting & terminating PVC armoured cable 3½ core 120
sq mm aluminium conductor with continuous 12.97 sq mm (8 SWG)
G.I. earth wire complete erected with glands & lugs, on wall/
trusses/pole or laid in provided trench/ pipe as per specification no. CB-
LT/AL (PWD CSR 2017-18 7-1-27)
Mtr 780.00
Rupees Seven
hundred Eighty
Only
124800.00
235.00 Mtr 24
Supplying, erecting & terminating PVC armoured cable 3½ core 70 sq
mm aluminium conductor with continuous 8.35 sq mm (10 SWG) G.I.
earth wire complete erected with glands & lugs, on wall/ trusses/pole
or laid in provided trench/ pipe as per specification no. CB-LT/AL.
(PWD CSR 2017-18 7-1-20)
Mtr 517.00
Rupees Five
hundred
Seventeen Only
121495.00
470.00 Mtr 25
Supplying, erecting & terminating PVC armoured cable 3½ core 50 sq
mm aluminium conductor with continuous 5.48 sq mm (12 SWG) G.I.
earth wire complete erected with glands & lugs, on wall/ trusses/pole
or laid in provided trench/ pipe as per specification no. CB-LT/AL
(PWD CSR 2017-18 7-1-19)
Mtr 398.00
Rupees Three
hundred Ninety
Eight Only
187060.00
80.00 Mtr 26
Supplying, erecting & terminating PVC armoured cable 3½ core 35
sq mm aluminium conductor with continuous 5.48 sq mm (12 SWG)
G.I. earth wire complete erected with glands & lugs, on wall/
trusses/pole or laid in provided trench/ pipe as per specification no. CB-
LT/AL (PWD CSR 2017-18 7-1-18)
Mtr 294.00
Rupees Two
hundred Ninety
Four Only
23520.00
403.90 Mtr 27
Supplying, erecting & terminating PVC armoured cable 4 core 25 sq
mm aluminium conductor with continuous 5.48 sq mm (12 SWG) G.I.
earth wire complete erected with glands & lugs, on wall/ trusses/pole
or laid in provided trench/ pipe as per specification no. CB-LT/AL
(PWD CSR 2017-18 7-1-22)
Mtr 276.00
Rupees Two
hundred
Seventy Six
Only
111475.25
150.00 Mtr 28
Supplying, erecting & terminating PVC armoured cable 3 core 2.5 sq
mm copper conductor continuous 5.48 sq mm (12 SWG) G.I. earth
wire complete erected with glands & lugs, on wall/ trusses/pole or laid
in provided trench/ pipe as per specification no. CB-LT/CU (PWD
CSR 2017-18 7-2-5)
Mtr 196.00
Rupees One
hundred Ninety
Six Only
29400.00
Page 40 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
50.00 Mtr 29
Supplying, erecting & terminating PVC armoured cable 4 core 4 sq
mm copper conductor continuous 5.48 sq mm (12 SWG) G.I. earth
wire complete erected with glands & lugs, on wall/ trusses/pole or laid
in provided trench/ pipe as per specification no. CB-LT/CU (PWD
CSR 2017-18 7-2-9)
Mtr 309.00
Rupees Three
hundred Nine
Only
15450.00
250.00 Mtr 30
Supplying, erecting & terminating PVC armoured cable 4 core 6 sq
mm copper conductor continuous 5.48 sq mm (12 SWG) G.I. earth
wire complete erected with glands & lugs, on wall/ trusses/pole or laid
in provided trench/ pipe as per specification no. CB-LT/CU (PWD
CSR 2017-18 7-2-10)
Mtr 416.00
Rupees Four
hundred Sixteen
Only
104000.00
300.00 Mtr 31
Supplying, erecting & terminating PVC armoured cable 4 core 10 sq
mm copper conductor continuous 5.48 sq mm (12 SWG) G.I. earth
wire complete erected with glands & lugs, on wall/ trusses/pole or laid
in provided trench/ pipe as per specification no. CB-LT/CU (PWD
CSR 2017-18 7-2-11)
Mtr 619.00
Rupees Six
hundred
Nineteen Only
185700.00
Sub-total: 1715968.25
G EARTHING
26.00 Each. 32
Supply, Installation, Testing and commissioning of UL Certified / CPRI
Tested Maintenance Free Earthing comprising of Electrode of 17.2 mm
diameter Low Carbon Steel with 250 micron Molecular Copper Bonded
Earthing Rod of Length 3m along with 25 kg Carbon Based
environment friendly back fill Ground Enhancing compound required to
fill up the excavated earth with required quantity as per specification no
EA-MOBI (PWD CSR 2017-18 9-1-5)
Each. 15935.00
Rupees Fifteen
Thousand Nine
hundred Thirty
Five Only
414310.00
800.00 Kg 33
Supplying and erecting GI strip of required size used for earthing on
wall and/or any other purpose with necessary GI clamps fixed on wall
painted with bituminous paint in an approved manner with joints
required. As per specification No EA-EP. (PWD CSR 2017-18 9-2-3)
Kg 190.00
Rupees One
hundred Ninety
Only
152000.00
40.00 Kg 34
Supplying and erecting Annealed bare copper wire of high purity of
different sizes used for earthing on wall with necessary copper clamps
fixed on wall/cable/ conduit with screws in an approved manner.(PWD
CSR 2017-18 9-2-4)
Kg 893.00
Rupees Eight
hundred Ninety
Three Only
35720.00
Page 41 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
30.00 Kg 35
Supplying and erecting copper strip of required size used for earthing
on wall and/or any other purpose with necessary copper clamps fixed
on wall painted with bituminous paint in an approved manner with joint
required as per specification No (EA-EP).(PWD CSR 2017-18 9-2-2)
Kg 851.00
Rupees Eight
hundred Fifty
One Only
25530.00
40.00 Kg 36
Supplying and erecting Annealed bare copper wire of high purity of
different sizes used for earthing on wall with necessary copper
clamps fixed on wall/cable/conduit with screws in an approved
manner. (PWD CSR 2017-18 9-2-4)
Kg 893.00
Rupees Eight
hundred Ninety
Three Only
35720.00
Sub-total: 663280.00
H EXTERNAL LIGHTING POINTS & ACCESSORIES
35.00 Each. 37
Supplying, erecting and commissioning of 60 W LED Street / Flood
light luminaire IP 66, made of single piece high pressure die cast
aluminum alloy (ADC1) body with heat resistant silicon gasket and
having PMMA optics with extra Clear thermally hardened glass cover.
The luminaire should be suitable for side entry on proveded typical
bracket of 40-60 mm dia The fixture should have high power LEDs,
cool white 4500K to 5700K and CRI≥75. with minimum 150
lumens/watt of delivering capacity LED, The System efficacy should be
> 85 %. The fixture must have an operating voltage range of 140V –
270V, frequency 50Hz +/- 3%, power factor > 0.95, with spike
protection of 4 KV. The driver efficiency should be >= 80% with drive
current between 350mA to 700mA at 240 v AC input. Total harmonic
distortion shall be < 10 % . and The fixture shall have Wind Blockage
area < 0.3 sqm, with average life of 50000 hrs with 80% lumen
maintenance @ Ta 35°C and after 10000 hrs burning life. The fixture
should conform to Electrical Safety Class 1 & IK08 rating. Fixture
should also be confirming to IEC60598-2-3: General purpose
Luminaries specifications. The electronic LED driver shall confirm to
EN61347-1: general and safety requirements EN61347-2-13: particular
requirements for DC or AC supplied electronic control gear for LED
modules, EN62384: DC or AC supplied electronic control gear for LED
Each. 4141.00
Rupees Four
Thousand One
hundred Forty
One Only
144935.00
Page 42 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
35.00 Each. 38
Providing & erecting 7 m high Hot Dip galvanised as per specification
BSEN ISO 1461, OCTAGONAL pole (without Bracket ) with bottom Dia
of 200 mm A/F, Top Dia of 100 mm, Base Plate of 275x275x16 mm /
290x290x16 mm, Sheet Thickness 3 mm, Each section shall be
fabricated out of individual plates duly folded and welded. There shall
be only one longitudinal seam weld per section. Hot dip internally and
externally having uniform thickness of 85 microns for bottom section
and 65 microns for top and middle section, Max. Dynamic loading to
withstand Max. Wind pressure As per IS 875 part 3. The welding
connection of the base flange shall be fully developed to the strength of
the entire section. The base flange shall be provided with
supplementary gussets between the bolt- holes to ensure elimination of
helical stress concentration.erected on Provided Cement Concrete
Foundation with Foundation Bolts M20x750 mm. with Inbuilt cable
junction box with connection Plate & terminals R,Y,G & B. complete
with all provided earthing & connections. with 1 no/2 no 6 Amp 230 V
MCB,s 29-1-1 ( Himast Octagonal Decorative pole and CCF( 2013 -
2014 ) )Completed
Each. 13780.00
Rupees Thirteen
Thousand
Seven hundred
Eighty Only
482300.00
35.00 Each. 39
Providing and erecting Galvanised 1000mm Single arm sword type
bracket with FRPdome and ball as per specification no OH-PL/PBKT
(PWD CSR 2017-18 8-3-30)
Each. 2426.00
Rupees Two
Thousand Four
hundred Twenty
Six Only
84910.00
35.00 Each. 40
Supplying and erecting M-24 ( Nut-bolt of ENB Grade) cement
concrete Foundation for bajaj make 7.0 / 9.0 mtr Galvanised Octagonal
pole. Of foundation size 400 x 400 x 1200 mm including excavation in
hard murum or Tar / Metal road as per requirement of proper size
foundation including footing , soiling at the bottom complete with
required curing etc as per given drawing BA/PMC/2004/ELE/109. 29-1-
5 ( Poles & Towers & CCF( 2010 - 2011 ) )Completed
Each. 4200.00
Rupees Four
Thousand Two
hundred Only
147000.00
Page 43 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
1050.00 M 41
Supplying, erecting & terminating PVC armoured cable 4 core 10 sq
mm aluminium conductor with continuous 5.48 sq mm (12 SWG) G.I.
earth wire complete erected with glands & lugs, on wall/ trusses/pole
or laid in provided trench/ pipe as per specification no. CB-LT/AL
(PWD CSR 2017-18 7-1-14)
M 184.00
Rupees One
hundred Eighty
Four Only
193200.00
200.00 M 42
Supplying, erecting & terminating PVC armoured cable 3 core 4 sq
mm copper conductor continuous 5.48 sq mm (12 SWG) G.I. earth
wire complete erected with glands & lugs, on wall/ trusses/pole or laid
in provided trench/ pipe as per specification no. CB-LT/CU (PWD CSR
2017-18 7-2-6)
M 251.00
Rupees Two
hundred Fifty
One Only
50200.00
35.00 Each. 43
Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia.
G.l. Rod complete with all materials as per specification No. EA-EP
(PWD CSR 2017-18 9-1-4 )
Mtr 1521.00
Rupees One
Thousand Five
hundred Twenty
One Only
53235.00
20.00 Kg 44
Supplying and erecting G.I. strip of required size used for earthing on
wall and/or any other purpose with necessary GI clamps fixed on wall
painted with bituminous paint in an approved manner with joint
required. as per specification No (EA-EP). (PWD CSR 2017-18 9-2-3 )
Kg 190.00
Rupees One
hundred Ninety
Only
3800.00
Sub-total: 1159580.00
J Dismantling & Shifting
3000.00 Point 45
Dismantling the existing light, fan, bell, clock, independent plug
point, wiring including circuit mains of all types along with accessories
etc.complete as per specification No: WG-DM/PW (PWD CSR 2017-
18 1-15-1 )
Point 8.00Rupees Eight
Only24000.00
900.00 Mtr 46
Dismantling the existing Telephone / Lan / Wan / TV cables and
wires of all sizes along with casing-capping / conduit complete as per
specification No: WG-DM/PW (PWD CSR 2017-18 1-15-2 )
Mtr 5.00Rupees Five
Only4500.00
12000.00 Mtr 47
Dismantling the existing Aluminium/copper mains,sub-mains wiring
upto 10 sq.mm. along with accessories etc.Complete as per
specification No: WG-DM/PW (PWD CSR 2017-18 1-15-3 )
Mtr 3.00Rupees Three
Only36000.00
Page 44 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
26.00 Each. 48Dismantling the existing W.T. fluorescent fitting/ S.V./ M.V/MH lamp
fitting from pole with brackets complete. (PWD CSR 2017-18 2-14-3 ) Each. 105.00
Rupees One
hundred Five
Only
2730.00
1200.00 Each. 49
Dismantling the existing W.T.fluoroscent fitting / S.V./ M.V/MH.lamp
/LED fitting from wall with brackets and making the site as origina
lcomplete.
Each. 45.00Rupees Forty
Five Only54000.00
60.00 Each. 50
Dismantling the existing ceiling fan/exhaust fan/cabin fan/bracket
fan complete with accessories, G.I. down rod, frame etc. and making
the site clear. (PWD CSR 2017-18 2-14-4 )
Each. 36.00Rupees Thirty
Six Only2160.00
40.00 Each. 51
Dismantling the existing switchgears, DB, and Bus bar of any size
complete with/ without board or angle iron frame (PWD CSR 2017-18 5-
12-1 )
Each. 90.00Rupees Ninety
Only3600.00
30.00 Each. 52
Making the site clear of dismantled DB and switch gears by refilling the
holes with cement mortar & finishing in an approved manner. (PWD
CSR 2017-18 5-12-2 )
Each. 66.00Rupees Sixty
Six Only1980.00
4.00 Each. 53
Dismantling any type of unservicable feeder pillar, Switch gear panel,
Capacitor Panel, Metering panel, Bus-bar Panel, Electronic Equipment
Panel, etc. and remaking the site good as original. Approx. size (upto
150 cm x 70 cm x 45 cm ) - Small Coupboard (PWD CSR 2017-18 5-
12-4 )
Each. 1247.00
Rupees One
Thousand Two
hundred Forty
Seven Only
4988.00
5.00 Each. 54
Dismantling any type of unservicable feeder pillar, Switch gear panel,
Capacitor Panel, Metering panel, Bus-bar Panel, Electronic Equipment
Panel, etc. and remaking the site good as original. Approx. size ( upto
200cm. x 90 cm x 45 cm and above) - Big Coupboard (PWD CSR
2017-18 5-12-5 )
Each. 1871.00
Rupees One
Thousand Eight
hundred
Seventy One
Only
9355.00
1500.00 Mt 55Dismantling the existing cables of all types & size upto 10 sq mm.
(PWD CSR 2017-18 7-12-1 ) Mt 14.00
Rupees
Fourteen Only21000.00
300.00 Mt 56Dismantling the existing cables of all types & size above 10 sq mm
upto 50 sq.mm. (PWD CSR 2017-18 7-12-2 ) Mt 21.00
Rupees Twenty
One Only6300.00
1800.00 Mt 57Dismantling the existing cables of all types & size above 50 sq mm.
(PWD CSR 2017-18 7-12-3 ) Mt 28.00
Rupees Twenty
Eight Only50400.00
50.00 Mt 58Refilling the holes for dismantled cables with cement mortar & finishing
in an aproved manner etc. complete (PWD CSR 2017-18 7-12-4 ) Mt 54.00
Rupees Fifty
Four Only2700.00
Page 45 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
350.00 Mt 59
Dismantling the existing underground cable without damaging it
with glands, cable end box including refilling the trench up to
ground level and making coils complete. (PWD CSR 2017-18 7-12-5 )
Mt 88.00Rupees Eighty
Eight Only30800.00
4.00 Each. 60
Dismantling the existing pole above 6 m height with brackets,
clamps, insulators, stay from the cement concrete foundation and
making the site clear by refilling the pits with excavated materials
and bringing it to the ground level. (PWD CSR 2017-18 8-8-2 )
Each. 800.00Rupees Eight
hundred Only3200.00
3.00 Each. 61Dismantling existing lightning arrestor set, insulator complete from DP
structure in an approved manner (PWD CSR 2017-18 8-8-4 ) Each. 93.00
Rupees Ninety
Three Only279.00
320.00 Kva 62
Dismentling unservicable DG set upto 50 kVA capacity alongwith
Switch gears & panel, etc. and remaking the site good as original.
(PWD CSR 2017-18 11-3-1 )
Kva 2373.00
Rupees Two
Thousand Three
hundred
Seventy Three
Only
759360.00
500.00 Kva 63 shifting of 320 kva DG set at one place to another place Kva 165.70
Rupees One
hundred Sixty
Five Paise
Seventy Only
82850.00
Sub-total: 1100202.00
8062445.25
INTERNAL
A POINT WIRING
Point wiring for light/fan/bell concealed type in min 20 mm PVC conduit
with 1.5 sq.mm. (2+1E) FR grade copper wires, moduler type switch,
earthing and required accessaries as per specification No: WG-
PW/CW (PWD CSR 2017-18 1-9-9)
653.0Poin
t1 Light Point 754.00
Rupees Seven
hundred Fifty
Four Only
492362.00
TOTAL EXTERNAL COST
Page 46 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
64.0Poin
t2 Fan Points Point 754.00
Rupees Seven
hundred Fifty
Four Only
48256.00
35.0Poin
t3 Exhaust fan Point Point 754.00
Rupees Seven
hundred Fifty
Four Only
26390.00
150.0Poin
t4
Point wiring for independent plug, concealed type in min 20 mm PVC
conduit with 1.5 sq.mm (2+1E) FR grade copper wires,moduler type
switch and socket, earthing and required accessaries as per
specification No WGPW/ SW (PWD CSR 2017-18 1-9-11)
Point 826.00
Rupees Eight
hundred Twenty
Six Only
123900.00
26.0 Nos 5
Supplying and erecting modular type switch 6A / 10A ISI mark
approved make duly erected on provided plate and box with wiring
connections complete. (PWD CSR 2017-18 1-8-1)
Nos 89.00Rupees Eighty
Nine Only2314.00
307.0 Nos 6
Supplying and erecting modular type switch 16A ISI mark approved
make duly erected on provided plate and box with wiring connections
complete. (PWD CSR 2017-18 1-8-2)
Nos 125.00
Rupees One
hundred Twenty
Five Only
38375.00
26.0 Nos 7
Supplying and erecting modular type 3 pin 6A multi socket with safety
shutter ISI mark approved make duly erected on provided plate and
box with wiring connections complete. (PWD CSR 2017-18 1-8-10)
Nos 116.00
Rupees One
hundred Sixteen
Only
3016.00
307.0 nos 8
Supplying and erecting modular type 3 pin 6 / 16A multi socket with
safety shutter ISI mark approved make duly erected on provided plate
and box with wiring connections complete. (PWD CSR 2017-18 1-8-11)
nos 179.00
Rupees One
hundred
Seventy Nine
Only
54953.00
2.0 Nos 9
Supplying and erecting modular type T.V. socket single outlet ISI mark
approved make duly erected on provided plate and box with wiring
connections complete. (PWD CSR 2017-18 1-8-14)
Nos 96.00Rupees Ninety
Six Only192.00
31.0 Nos 10
Supplying and erecting modular type telephone socket one gang with
safety shutter ISI mark approved make duly erected on provided plate
and box with wiring connections complete. (PWD CSR 2017-18 1-8-15)
Nos 95.00Rupees Ninety
Five Only2945.00
Page 47 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
19.0 Nos 11
Supplying and erecting modular type computer Jack RJ 45 with safety
shutter ISI mark approved make duly erected on provided plate and
box with wiring connections complete. (PWD CSR 2017-18 1-8-17)
Nos 120.00
Rupees One
hundred Twenty
Only
2280.00
64.0 Nos 12
Supplying and erecting modular type electronic step regulator for fan
two module ISI mark approved make duly erected on provided plate
and box with wiring connections complete. Note: Add Rs 60/- provision
of additional two modules for box and double plate (PWD CSR 2017-18
1-8-23)
Nos 410.00
Rupees Four
hundred Ten
Only
26240.00
100.0 Nos 13
Supplying and erecting modular type blanking plate one module ISI
mark approved make duly erected on provided plate & box. (PWD CSR
2017-18 1-8-25)
Nos 21.00Rupees Twenty
One Only2100.00
130.0 Nos 14
Supplying and erecting unbreakable concealed type modular switch
box with double mounting plate for 2 module duly erected flush to wall
with required chiselling and finishing with cement morter / POP as per
required to match the background in an approved manner. (PWD CSR
2017-18 1-8-36)
Nos 239.00
Rupees Two
hundred Thirty
Nine Only
31070.00
85.0 Nos 15
Supplying and erecting unbreakable concealed type modular switch
box with double mounting plate for 3 module duly erected flush to wall
with required chiselling and finishing with cement morter / POP as per
required to match the background in an approved manner. (PWD CSR
2017-18 1-8-37)
Nos 273.00
Rupees Two
hundred
Seventy Three
Only
23205.00
10.0 Nos 16
Supplying and erecting unbreakable concealed type modular switch
box with double mounting plate for 4 module duly erected flush to wall
with required chiselling and finishing with cement morter / POP as per
required to match the background in an approved manner. (PWD CSR
2017-18 1-8-38)
Nos 306.00
Rupees Three
hundred Six
Only
3060.00
10.0 Nos 17
Supplying and erecting unbreakable concealed type modular switch
box with double mounting plate for 6 module duly erected flush to wall
with required chiselling and finishing with cement morter / POP as per
required to match the background in an approved manner. (PWD CSR
2017-18 1-8-39)
Nos 410.00
Rupees Four
hundred Ten
Only
4100.00
Page 48 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
25.0 Nos 18
Supplying and erecting unbreakable concealed type modular switch
box with double mounting plate for 8 module duly erected flush to wall
with required chiselling and finishing with cement morter / POP as per
required to match the background in an approved manner. (PWD CSR
2017-18 1-8-40)
Nos 483.00
Rupees Four
hundred Eighty
Three Only
12075.00
30.0 Nos 19
Supplying and erecting unbreakable concealed type modular switch
box with double mounting plate for 12 module duly erected flush to wall
with required chiselling and finishing with cement morter / POP as per
required to match the background in an approved manner. (PWD CSR
2017-18 1-8-41)
Nos 535.00
Rupees Five
hundred Thirty
Five Only
16050.00
Sub-total: 912883.00
B CIRCUIT WIRING
18000.0 MTR 20
Supplying & laying Rigid PVC conduit 25mm Dia with necessary
accessories in RCC work/false ceiling/false flooring as per specification
No. WG-MA/CC, para no. 1.2.1 (PWD CSR 2017-18 1-1-10)
MTR 107.00
Rupees One
hundred Seven
Only
1926000.00
3500.0 MTR 21
Supplying and erecting UPVC reinforced flexible conduit 50 mm in dia.
conforming to I.S. and approved make with required number of
couplings, PVC bushes, check nuts etc. complete. (for Stage Lighting
To Light control room ) (PWD CSR 2017-18 1-2-6)
MTR 179.00
Rupees One
hundred
Seventy Nine
Only
626500.00
3000.00 MTR 22
Supplying & erecting mains with 2x1.5 sq.mm F.R.L.S copper PVC
insulated wire laid in provided conduit/trunking/inside pole/Bus bars or
any other places as per specification No: WG-MA/BW (PWD CSR
2017-18 1-3-4)
MTR 44.00Rupees Forty
Four Only132000.00
4000.00 MTR 23
Supplying & erecting mains with 3x2.5 sq.mm F.R. L.S copper PVC
insulated wire laid in provided conduit/trunking/inside pole/Bus bars or
any other places as per specification No: WG-MA/BW (PWD CSR
2017-18 1-3-14)
MTR 90.00Rupees Ninety
Only360000.00
8000.00 MTR 24
Supplying & erecting mains with 2x2.5 sq.mm F.R.L.S copper PVC
insulated wire laid in .provided conduit/trunking/inside pole/Bus bars or
any other places. as per specification No: WG-MA/BW (DB TO SB,
POWER POINT ,MAINS AUDIOTORAM LIGHTING,) (PWD CSR 2017-
18 1-3-6)
MTR 66.00Rupees Sixty
Six Only528000.00
Page 49 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
3000.00 MTR 25
Supplying & erecting mains with 2x4 sq.mm F.R.L.S copper PVC
insulated wire laid in Provided conduit/trunking/inside pole/Bus bars or
any other places. as per specification No: WG-MA/BW (DB to Power
Point ) (PWD CSR 2017-18 1-3-8)
MTR 89.00Rupees Eighty
Nine Only267000.00
7000.00 MTR 26
Supplying & erecting mains with 3x2.5 sq.mm F.R. L.S copper PVC
insulated wire laid in provided conduit/trunking/inside pole/Bus bars or
any other places as per specification No: WG-MA/BW (for Stage
Lighting To Light control room ) (PWD CSR 2017-18 1-3-14)
MTR 90.00Rupees Ninety
Only630000.00
5000.00 MTR 27
Supplying & erecting mains with 2x6 sq.mm F.R L.S copper PVC
insulated wire laid in provided conduit/trunking/inside pole/Bus bars or
any other places. as per specification No: WG-MA/BW (4Nos Main
DB to sub DB, 1PH & 3PH supply) (PWD CSR 2017-18 1-3-10)
MTR 125.00
Rupees One
hundred Twenty
Five Only
625000.00
Sub-total: 5094500.00
C ELECTRICAL DB
5.00Eac
h28
Supplying & erecting triple pole and neutral distribution board
(TPNDB) with door surface/ flush mounted suitable for 3 Pole MCCB
as Incommer & outgoing SP MCB (24 Poles) or TP MCB of 8 ways (24
Poles) , on iron frame. (Vertical Busbar type) as per specification No.
SW-SWR/MCBDB1 (PWD CSR 2017-18 5-4-26)
MTR 7914.00
Rupees Seven
Thousand Nine
hundred
Fourteen Only
39570.00
7.00Eac
h29
Supplying & erecting triple pole and neutral distribution board (TPNDB)
surface/ flush mounted, suitable for SPMCB of 12 ways, on iron / G.I.
frame/wooden board.(Horizontal type) as per specification No.
SWSWR/ MCBDB (PWD CSR 2017-18 5-4-1)
Each 2246.00
Rupees Two
Thousand Two
hundred Forty
Six Only
15722.00
8.00Eac
h30
Supplying & erecting triple pole and neutral distribution board (TPNDB)
surface/ flush mounted suitable for SPMCB of 24 ways, on iron / G.I.
frame/wooden board.(Horizontal type) as per specification No.
SWSWR/ MCBDB (PWD CSR 2017-18 5-4-2)
Each 2916.00
Rupees Two
Thousand Nine
hundred Sixteen
Only
23328.00
4.00Eac
h31
Supplying and erecting single pole and neutral distribution board
(SPNDB) surface/flush mounted with 2 ways for incoming and 6 ways
for outgoing SP MCB’s on iron/ G.I. frame/wooden board as per
specification No. SW-SWR/MCBDB (PWD CSR 2017-18 5-4-15)
Each 977.00
Rupees Nine
hundred
Seventy Seven
Only
3908.00
Page 50 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
4.00Eac
h32
Supplying and erecting single pole and neutral distribution board
(SPNDB) surface/flush mounted with 2 ways for incoming and 10 ways
for outgoing SP MCB’s on iron/ G.I. frame/wooden board as per
specification No. SW-SWR/MCBDB (PWD CSR 2017-18 5-4-16)
Each 1187.00
Rupees One
Thousand One
hundred Eighty
Seven Only
4748.00
5.00Eac
h33
Providing & erecting 3 Pole MCCB upto 100A, 415V capacity with S.C.
rating 25 kA (Ics=100% of Icu), thermal setting with provided leads on
iron frame/wooden board as per specification No. SW-SWR/MCCB
(PWD CSR 2017-18 5-5-1)
Each 5238.00
Rupees Five
Thousand Two
hundred Thirty
Eight Only
26190.00
12.00Eac
h34
Supplying, erecting & marking FPMCB 40A to 63A in provided
distribution board as per specification No. SW-SWR/MCB (PWD CSR
2017-18 5-3-17)
Each 1561.00
Rupees One
Thousand Five
hundred Sixty
One Only
18732.00
15.00Eac
h35
Supplying, erecting & marking TPMCB 40A to 63A in provided
distribution board as per specification No. SW-SWR/MCB (PWD CSR
2017-18 5-3-15)
Each 1164.00
Rupees One
Thousand One
hundred Sixty
Four Only
17460.00
15.00Eac
h36
Supplying, erecting & marking SPMCB 40A to 63A C- series (for
motor/power) in provided distribution board as per specification No.
SW-SWR/MCB (PWD CSR 2017-18 5-3-4)
Each 384.00
Rupees Three
hundred Eighty
Four Only
5760.00
340.00Eac
h37
Supplying, erecting & marking SPMCB 6A to 32A, C-series (for
motor/power) in provided distribution board as per specification No.
SWSWR/ MCB (PWD CSR 2017-18 5-3-2)
Each 191.00
Rupees One
hundred Ninety
One Only
64940.00
8.00Eac
h38
Providing, erecting & commissioning RCCB only of electro magnetic
type with 30/100/300 mA sensitivity and having capacity of 40A 2 pole
complete as per specification No. SWRCCB/ RCCB (PWD CSR 2017-
18 5-6-2)
Each 2435.00
Rupees Two
Thousand Four
hundred Thirty
Five Only
19480.00
15.00Eac
h39
Providing, erecting & commissioning RCCB only of electro magnetic
type with 30/100/300mA sensitivity and having capacity of 40A. 4 pole
complete as per specification No. SWRCCB/ RCCB (PWD CSR 2017-
18 5-6-5)
Each 3057.00
Rupees Three
Thousand Fifty
Seven Only
45855.00
Sub-total: 285693.00
D CABLE TRAY
Page 51 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
300.00 m 40
Providing & erecting Hot dipped Galvanised Perforated type Cable tray
manufactured from 16 swg (1.6 mm thick) GI sheet of 300 mm width &
75 mm height complete with necessary coupler plates & hardware in
approved manner. (PWD CSR 2017-18 7-11-8)
m 766.00
Rupees Seven
hundred Sixty
Six Only
229800.00
350.00 m 41
Providing & erecting Hot dipped Galvanised Perforated type Cable tray
manufactured from 16 swg (1.6 mm thick) GI sheet of 400 mm width &
75 mm height complete with necessary coupler plates & hardware in
approved manner. (PWD CSR 2017-18 7-11-9)
m 915.00
Rupees Nine
hundred Fifteen
Only
320250.00
400.00 m 42
Providing & erecting Hot dipped Galvanised Perforated type Cable tray
manufactured from 16 swg (1.6 mm thick) GI sheet of 500 mm width &
75 mm height complete with necessary coupler plates & hardware in
approved manner. (PWD CSR 2017-18 7-11-10)
m 1064.00
Rupees One
Thousand Sixty
Four Only
425600.00
Sub-total: 975650.00
E FAN and LIGHT FIXTURES
63.00Eac
h54
Supplying and erecting fan hook box of 10 mm M.S. round barbounded
to the R.C.C. bars upto 50 mm length each side andpierced through a
16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia.or equivalent square
size and having depth upto 75 mm completeerected with duly painted
by one coat of red oxide paint and two coatsof paint erected in position
and without any leakage of slurry of cementconcrete on either side of
thebbox and positioned to the bottom level ofthe slab. (PWD CSR 2017-
18 2-12-5)
Each 152.00
Rupees One
hundred Fifty
Two Only
9576.00
64.00Eac
h55
Supplying and erecting ‘B’ grade G.I.pipe/M.S. pipe down rod
dulypainted for fan complete erected with PVC three core flexible cable
1 sq. mm copper PVC wire. (PWD CSR 2017-18 2-12-6)
Each 216.00
Rupees Two
hundred Sixteen
Only
13824.00
64.00Eac
h56
Supplying and erecting Five Star Rated Energy Saving Ceiling Fan 230
V A.C. 50 cycles 1200 mm complete erected in position as
perspecifcation no. FG-FN/CF
Each 1994.00
Rupees One
Thousand Nine
hundred Ninety
Four Only
127616.00
35.00Eac
h57
Supplying and erecting Exhaust fan medium duty 230 V A.C. 50 cycles
225 mm. 1400RPM with condensor complete erected in position with
necessary materials. Fanmotor with moisture proof treatment and ‘E’
class insulation and marking Sr. No. & date of erction. (PWD CSR
2017-18 2-13-16)
Each 1901.00
Rupees One
Thousand Nine
hundred One
Only
66535.00
Page 52 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
1.00Eac
h58
Supply Installation Testing and Commissioning of 750mA Power
Supply Module, DIN-Rail Mount ,With Fast Connector,110V/220V AC
Input 50-60Hz, DC24/750mA output. (Make: Crabtree)
Each 14300.00
Rupees
Fourteen
Thousand Three
hundred Only
14300.00
2.00Eac
h59
Supply Installation Testing and Commissioning of Alluminium Series 8
Buttons Smart Wall Panel, IR Remote Control,(Optional) , Wall Switch
to control light scene. (Make:Crabtree)
Each 21870.00
Rupees Twenty
One Thousand
Eight hundred
Seventy Only
43740.00
3.00Eac
h60
Supply Installation Testing and Commissioning of Panel Power
Interface for iAlluminium Series wall mount keypad.(Make:Crabtree)Each 7269.00
Rupees Seven
Thousand Two
hundred Sixty
Nine Only
21807.00
3.00 Nos 61
Supply Installation Testing and Commissioning of 64 Ch. new DALI
Ballast Controller,DIN-Rail Mount, to transfer signal from Crabtree-BUS
to DALI control signal, with Scene Control function.(Make:Crabtree)
Nos 26527.00
Rupees Twenty
Six Thousand
Five hundred
Twenty Seven
Only
79581.00
1.00Eac
h62
Supply Installation Testing and Commissioning of DALI power supply
for DALI ballasts. (Make:Tridonic)Each 27135.00
Rupees Twenty
Seven
Thousand One
hundred Thirty
Five Only
27135.00
1.00 Nos 63Supply Installation Testing and Commissioning of ip gateway fr
programming (make:Crabtree)Nos 18360.00
Rupees
Eighteen
Thousand Three
hundred Sixty
Only
18360.00
1.00 Nos 64Supply Installation Testing and Commissioning of Automation DB with
MCB and wire's. (Make: Various)Nos 13500.00
Rupees Thirteen
Thousand Five
hundred Only
13500.00
Page 53 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
45.00 Nos 65
Supply Installation Testing and Commissioning of PLUTO Neo PANEL
2X2 Dimension 596X596X70mm System Power48W CCT 5700K
Nominal Voltage (V)240 Main Current (A)0.210 PowerFactor >0.95
Lumen Output (lm)4000 With DALI Ballast Cat : LHEWEIP7JL1W034
Havells or ( Equivalent approval make )
Nos 7339
Rupees Seven
Thousand Three
hundred Thirty
Nine Only
330255.00
95.00 Nos 66
Supply Installation Testing and Commissioning of ENDURA DL Neo
15W Dimension 149X45 Cutout 155mm System Power 15W CCT
6000K Nominal Voltage (V)240 Main Current (A)0.070 PowerFactor
>0.95 Lumen Output (lm) 1200 with DALI Ballast (for lower & Upper
Balcony) Cat : LHEBJNP7NZ1W015 Havells or ( Equivalent
approval make )
Nos 5214
Rupees Five
Thousand Two
hundred
Fourteen Only
495330.00
180.00 Nos 67
Supply Installation Testing and Commissioning of INTEGRA 15W
Dimension 158X90 Cutout 138mm System Power 15W CCT 6000K
Nominal Voltage (V)240 Main Current (A)0.070 PowerFactor >0.95
Lumen Output (lm) 1200 (IN Entrance,passage,Room)
Cat : LHEBGSP7PZ1W015 Havells or ( Equivalent approval make )
Nos 1099
Rupees One
Thousand
Ninety Nine
Only
197820.00
20.00 Nos 68
Supply Installation Testing and Commissioning ENDURA DL Neo 18W
Dimension 149X45 Cutout 155mm System Power 15W CCT 6000K
Nominal Voltage (V)240 Main Current (A)0.070 PowerFactor >0.95
Lumen Output (lm) 1650 ( For Porch) Cat : LHEBJNP7PV1W018
Havells or ( Equivalent approval make )
Nos 1430
Rupees One
Thousand Four
hundred Thirty
Only
28600.00
20.00 Nos 69
Supply Installation Testing and Commissioning BAMBO Bollard
System Power 9W Nominal Voltage (V)240 Main Current (A)0.044
Power Factor >0.90 800K (for landscape ) Cat : LHENAXP7PZ6K008
Havells or ( Equivalent approval make )
Nos 3793
Rupees Three
Thousand
Seven hundred
Ninety Three
Only
75860.00
20.00 Nos 70
Supply Installation Testing and Commissioning ENDURA SPIKE
Innovative design, energy saving 3.5W LED Spike luminaire in
engineering plastic IP66 housing. Cat : LHEVAWP5UN6K3X5 Havells
or ( Equivalent approval make )
Nos 2925
Rupees Two
Thousand Nine
hundred Twenty
Five Only
58500.00
Page 54 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
6.00 Nos 71
Supply Installation Testing and Commissioning JETA COMPACTO (L)
LED IP65 Dimension 225X186X151 30W SMD Nominal Voltage
(V)240 Main Current (A)0.135 PowerFactor >0.90 Lumen Output (lm)
2400 (For Natraj Statue Area ) Cat: LHEPCYU7N46J030 Havells or
( Equivalent approval make )
Nos 3253
Rupees Three
Thousand Two
hundred Fifty
Three Only
19518.00
200.00 Nos 72
Supply Installation Testing and Commissioning 18W batten with
decorative shock proof ultra slim linear LED ligting fixture provides
excellent light with 1800 lumens output, col temp 5700k, Cat :
LHEXBQP7IN1W018 Havells or ( Equivalent approval make )
Nos 528
Rupees Five
hundred Twenty
Eight Only
105600.00
70.00 Nos 73
Supply Installation Testing and Commissioning 21 W Surface mounted
ENDURA Neo DL LED downlighter with white powder coated
aluminium housing with integrated electronic driver, 5700K wih Havells
Cat no LHEAAGP7IA1W018 Havells or ( Equivalent approval make )
Nos 1890
Rupees One
Thousand Eight
hundred Ninety
Only
132300.00
25.00 Nos 74
Supply Installation Testing and Commissioning 2 ft surface and wall
mounted 9 w LED batten with polycarbonate housing & integrated
electronic driver,6000K, with Havells Cat no LHEXBQP7IN1W009 or
equivalent
Nos 430
Rupees Four
hundred Thirty
Only
10750.00
300.00 Nos 75
Supply Installation Testing and Commissioning Flexible 24 W LED strip
uses high brightness SMD LED as the light source for indoor
application, 6000K D37 Cat no LHEHDEP7UN1F024 (driver for per 5m
strip) Havells or ( Equivalent approval make )
Nos 1885
Rupees One
Thousand Eight
hundred Eighty
Five Only
565500.00
12.00 Nos 76
Supply Installation Testing and Commissioning Ranger Midi System
Power 67W Voltage (V) AC100-277V Beam Angle 25°x60° Lumen
(lm) 2457 Colour Temp. (CCT) RGB
Nos 20800
Rupees Twenty
Thousand Eight
hundred Only
249600.00
Sub-total: 2705607.00
F LIGHTNING ARRESTOR
4.00 Each. 77
Supplying & erecting conventional spike type air termination suitable to
carry lightning stroke made up of heavy gauge 40 mm dia copper pipe
of standard length with 5 Nos. copper spikes fixed on copper ball as air
terminals duly threaded in copper pipe erected on provided foundation
in an approved manner. (PWD CSR 2017-18 9-3-1)
Each. 5023.00
Rupees Five
Thousand
Twenty Three
Only
20092.00
Page 55 of 60
Qty. Unit No. Description of Item Unit Rate Rate In Words Amount
100.00 Kg 78
Supplying and erecting GI strip of required size used for earthing on
wall and/or any other purpose with necessary GI clamps fixed on wall
painted with bituminous paint in an approved manner with joints
required. As per specification No EA-EP. (PWD CSR 2017-18 9-2-3)
Kg 190.00
Rupees One
hundred Ninety
Only
19000.00
Sub-total: 39092.00
G CONTROL WIRE FOR DALI SYSTEM
1000.0 MTR 79
Supplying & laying Rigid PVC conduit 25mm Dia with necessary
accessories in RCC work/false ceiling/false flooring as per specification
No. WG-MA/CC, para no. 1.2.1 (PWD CSR 2017-18 1-1-10)
MTR 107.00
Rupees One
hundred Seven
Only
107000.00
1000.00 MTR 80
Supplying & erecting mains with 2x1.5 sq.mm F.R.L.S copper PVC
insulated wire laid in provided conduit/trunking/inside pole/Bus bars or
any other places as per specification No: WG-MA/BW (PWD CSR
2017-18 1-3-4)
MTR 44.00Rupees Forty
Four Only44000.00
200.00 MTR 81
Supplying & installing UTP networking Cat-6
cable suitable for LAN / WAN Computer networking
as per specification No. WG-COC/NC
MTR 50.00Rupees Fifty
Only10000.00
1.00 MTR 82
Supplying & erecting triple pole and neutral
distribution board (TPNDB) surface/ flush
mounted SP /TP MCBs of total 12 ways, on
iron / G.I. frame/wooden board.(Vertical Busbar
type) as per specification No. SWSWR/
MCBDB
MTR 4470.00
Rupees Four
Thousand Four
hundred
Seventy Only
4470.00
Sub-total: 165470.00
10178895
18241340.25
TOTAL INTERNAL COST
TOTAL ELECTRICAL COST
Page 56 of 60
Project Name
Item
No.Qty Unit Items Rate Per Amount
1 6 Each
System Installation,Testing & Commissioning of 6 Channel 4Kw per
channel LCD display, Direct Dimming (Make: Raytech or
Equivalent)
64875.00 ( Rs. Sixtyfour
thousand Eight hundred
Seventy five only)
Each 3,89,250.00
2 2 Each
System Installation,Testing & Commissioning ofPortable operating 2
desk 12+6 channel consol with dual preset, 2 ceoss fade master
fader with flashing cricuitry, black out switch 0 -180 sec. Group hiper
fader for stage lights as per direction of authority. (Make Satan OR
Equivalent)
106170.00 (Rs.One Lakh Six
thousand one hundred
seventy only)
Each 2,12,340.00
3 10 Each
System Installation,Testing & Commissioning of1000 watt four
compartment cyclorama withmulty curved reflector R.7s base holder,
filter frame, power cord, safety wire mesh, diecast alluminium 'C'
clamps with saely chain 1000 Watt, linear halogen lamps 4 nos.
complete. as per direction of authority. (Make Satan OR Equivalent)
21075.00 (Rs.Twenty one
thousand seventy five only)Each 2,10,750.00
4 12 Each
System Installation,Testing & Commissioning of1000 Watt halogen
frsnel spot lights complete wth 6" lense, G x 9.5 base lamp socket, 4
leaf barndoor, set of scrim, diecast Alu, 'C' clamp with satety chain
and 1000 WATT halogen lamp as per direction of authority. (Make
Satan OR Equivalent)
15800.00 (Rs.Fifteen
Thousand Eight hundred only)Each 1,89,600.00
Memorandum showing the items of work to be carried out
Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION E :- STAGE LIGHTS (PART B)
SCHEDULE B
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
PCMC - CIVIL WORKS
Page 57 of 60
5 10 Each
System Installation,Testing & Commissioning of1000 WATT amini
halogen flood light with integral 4 leaf barndoor, R-7s base double
ended, diacast al. C' clamp with safety chain and 1000 WATT inear
halogen lamp / as per direction of authority. (Make Satan OR
Equivalent)
8290.00 ( Rs. Eight Thousand
Two hundred Ninety Only)Each 82,900.00
6 10 Each
System Installation,Testing & Commissioning of1000 WATT
PARCAN made out of spun alluminium provided with G.16 d. base
lamp socket, lamp retaining ring, power cord filter frame, diacast al.
'C' clamp and 1000 WATT halogen lamp (PARCAN-64) as per
direction of authority (Make Satan OR Equivalent)
8045.00 (Rs. Eight thousand
Forty five Only)Each 80,450.00
7 6 Each
System Installation,Testing & Commissioning of1000 WATT dual
lens profile spot light complete with plano covnes lens, G x 9.5 base
lamp socket, drop in IRIS, diacast Al. 'C' clamp with safety chain and
1000 W.G. x 9.5 base halogen lamp (P.S. 1002 PC) as per direction
of authority (Make Satan OR Equivalent)
22195.00 ( Rs.Twenty two
thousand one hundred Ninety
five only)
Each 1,33,170.00
8 6 Each
System Installation,Testing & Commissioning of1000 sinbgle lens
profile spot light with plano conves idns, G x 9 base lamp base,
diacast, Al. C' clamp with safety chain and 1000 WATT G x 9.5 base
halogen lamp as per direction of authority (Make Satan OR
Equivalent)
23470.00 (Rs.Twenty three
thousand Four hundred
Seventy only)
Each 1,40,820.00
9 6 Each
System Installation,Testing & Commissioning of2000 WATT high
effeciency spot light with 10" dia fresnel lens, GY-16 base lamp
socket 2000 watt halgogen lamp diacast al. C" clamp with safety
chain as per direction of authority (Make Satan OR Equivalent)
27910.00 (Rs. Twenty seven
thousand Nine hundred Ten
only)
Each 1,67,460.00
10 6 Each
System Installation,Testing & Commissioning of2000 WATT a
hologen spot light complete with 4 color altaer holder magagine,
operating handle, silding YOKA, GY-16 base lamp, diacast Al.'C'
clamp with safety chain (Make Satan OR Equivalent)
53065.00 ( Rs. Fiftythree
thousand Sixty five only)Each 3,18,390.00
11 5 Each
System Installation,Testing & Commissioning of3 section heavy duty
floor stand with castors. TYPE STD -5 as per direction of authority.
(Make Satan OR Equivalent)
5030.00 ( Rs. Five thousand
Thirty only)Each 25,150.00
Page 58 of 60
12 2 Each
System Installation,Testing & Commissioning ofSpotting attachement
suitable for 1000 WATT spot light. Type S.A. 1006 as per direction of
authority. (Make Satan OR Equivalent)1900.00 (Rs.One thousand
Nine hundred only)Each 3,800.00
13 1 Each
System Installation,Testing & Commissioning ofDimmer power pack
of 6 x 4 KW = 24 KW type 3 phase 50 HZ unit complete with control
console and interconnected wire. ( These specification are changed
to Elctronic dimmer 6 x 4 = 24 KW rated and similar to the stage to
the dimmer to make it interchangble in emergency and complete with
control console as per direction of authority.
(Make: Raytech or Equivalent)
67280.00 ( Rs. Sixty seven
thousand Two hundred Eighty
Only.)
Each 67,280.00
14 1 Each
System Installation,Testing & Commissioning ofElectrical panel for
100 stage light points with required Controllers, Switches, MCBs,
Patch Cables 15 AMP socket and top with 1.5 mm 2 core cable for
control room to stage light bar for 35 point etc. all the components
should be from reputed manufacturers having ISO certificate &
confirming to required IS standards- Supply, Installation &
Commissioning at site, including all required Accessories, cables,
connectors, mounting & installation hardware as per design &
Instructions of Architect / Consultant. (Custom Make)
124595.00 (Rs.One lakh
Twenty four thousand five
hundred ninety five only)
Each 1,24,595.00
21,45,955.00Total INR
Page 59 of 60
Item
No.Qty Unit Items Rate Rate in Words Amount
1 36.00 Each
Suppling, installing, testing and commisioning
of 10KWp capacity On Grid Solar Power Pack
with GI mounting structure and inter
connecting wires /cables without battery bank
SPV Modules of 10 KWp,Solar power
conditioning unit of min. 10KVA capacity
complete with 5 years on site perpormance
warrenty as per specification PCMC
675191.00
Rupees Six
Lakh Seventy
Five thousand
One hundred
Ninety One Only
2,43,06,876.00
2 3.00 Each
Supplying and erecting 4 pole power
contractor 440V 40A for time switch complete
erected on wooden block /provided box,with
necessary materials.
3792.00
Rupees Three
Thousand Seven
hundred Ninety
Two Only
11,376.00
3 720.00
per
KW
per
year
PCMC-14-9 Providing
Comprehensive annual Maintenance and
repairs for solar power on grid system
without back up system with all required
spares at the time of break down repairs
and ruiteen maintainance of solar system
cosisting solar PV panels invertor
weather proof IP 67 rated junction box,
distributionn boards, inter connections,
armoured/unarmoured TUV certified
copper cables.
4993.00
Rupees Four
Thousand Nine
hundred Ninety
Three Only
35,94,960.00
Rs 2,79,13,212.00
PCMC - CIVIL WORKS
PIMPRI CHINCHWAD MUNICIPAL CORPORATION, PIMPRI -18
TOTAL OF SOLAR WORKS
Rupees Two Crore Seventy Nine Lakh Thirteen thousand Two hundred Twelve Only
SCHEDULE B / ABSTRACT
Memorandum showing the items of work to be carried out
Project Name Renovation Of Prof. Ramkrishna More Auditorium At Chinchwad
SECTION G :- SOLAR WORKS (PART B)
SOLAR WORKS
Page 60 of 60