PDMS COMMANDSPIPING COMMANDS.1. ADD ALL PIP
2. REM ALL PIP
3. MOVE U THROU IDP@
4. MOVE E THROU IDP@ 5. MOVE W THROU IDP@ 6. MOVE N THROU IDP@
7. MOVE S THROU IDP@ 8. Q DTXR (To See Name Of Component)
9. Q STEXT (naming For Attachment)
10. Q ATT 11. REPR INSU ON/OFF UPDATE
12. CONN NEXT (Connection to next element)
13. FCONN (For force connection)
14. DIST 500
15. AXES AT PH (To see Axes of Pipe Head)
16. AXES AT PT (To see Axes of Pipe Head)
17. AXES OFF 18. BY U 500
19. BY D 500
20. BY E 500
21. BY W 500
22. BY S 500
23. BY N 500
24. Q NAME 25. ROTATE BY 45 (Rotated command)
26. ROT BY 90 ABOUT Z THRO ID@ (Rotated)
27. NEW BOX COPY PRE ROT BY 90 ABOUT Z THRO IDP@
28. Q PARA (To check nozzle size)
29. Q CATREF (To See nozzle Rating)
30. Q POS IN WORLD
31. CH CE (check current element) for piping.
32. Q SPREF (check piping Spec)
33. Q ORI (To see the orientation)
34. DIR D (Direction Down) U E W N S (For elbow, tee, valve) 35.
Q P1/P2/P3 (To see pipe Bore Direction Connection type and
Position) 36. Q HBORE
37. Q TBORE
38. Q LBORE
39. NEW BRA COPY PREV BY E/W/S/N/U/D 100 40. Q U (To see the
elevation)
41. Q ANGLE (For change the angle)
42. THRO NEXT (To connect element to next component)
43. Q LTLE (To cheek pipe length)
44. Q MEM
45. Q RTEX OF DETREF (To see element type and detail)
46. CONN IDP@ TO IDP Q CE
47. Q PL (For Direction and position)
48. BRA CONN PH TO FIST MEM
49. BRA CONN PT TO NOZZ ID@
50. BRA CONN PT TO LAST
51. RAD 500 (Control Valve Radius)
52. HEI 500 (Control Valve Height)
53. BACK (Backward)
54. FORW (Forward)
55. FOR DRAIN PIPE
a. ADD ATT (For isometric note)
b. Q ATT
c. TCONNECT OPEN
d. Q STEXT
e. STEXT 'DRAIN POINT'
1. FOR SLOPE LINE /ROTATED ELBOW
a. FORWARDS (Select in piping components) b. DIR TOW NEXT
c. BACKWARDS (Select in piping components)
d. DIR TOW NEXT
1. MTOC OFF (Not want in isometric bill of material)
2. MTOC ON (Want in isometric bill of material)
STRUCTURE COMMANDS.1. AXES AT POSE/S (end or start)
2. Q POSE WRT/*
3. EXTE END BY D 500 WRT/*
4. EXTE START BY U 500 WRT/*
5. EXTE END/START THRO ID@
6. EXTE END/START THRO IDPL@ (PL-Pline)
7. Q CUTL (To see length of section) 8. Q POS PPLINE BOS IN/*
(bos tos na )
9. ADD ALL STR
10. REM ALL STR
11. Q ATT
12. BY U//D/E/W/N/S 500
13. Q DRNS DRNE
14. DRNSTART S 45 E (Direction and angle)
15. DRNEND S 45 W (Direction and angle)
EQUIPMENT COMMANDS.
1. ADD ALL EQUI
2. REM ALL EQUI
3. MOVE U THROU IDP@
4. MOVE E THROU IDP@
5. MOVE W THROU IDP@
6. MOVE N THROU IDP@
7. MOVE S THROU IDP@
8. Q ATT 9. REPR HOLES ON/OFF UPDATE
10. REPR OBST ON/OFF UPDATE
11. To Copy New Equipment
a. VAR1 NAME b. NEW EQU COPY $V1 (To Include Equipment in
another zone)
1. BY U//D/E/W/N/S 500 2. NEW BOX COPY PRE
3. NEW BOX XLEN 400 YLEN 250 ZLN 150
4. NEW CYL COPY PRE
5. NEW PYRE COPY PRE
6. NEW NOZZ COPY PRE
OTHERS COMMAND.1. For copy equip/sub equipment from one project
to another project
a. FILE /FILE NAME.TXT
b. OUTPUT CE c. TERM
1. For pest equipment / sub equipment from one project to
another project)
a. $M FILE NAME.TXT3. EXPLANTa. repre level 6
b. repre level 6
c. repre level pipe 6
d. repre level stru 6
e. repre level nozz 6
f. EXPORT SYSTEM /explant
g. Export file /c:\export10 (file name)
ADD SITE a. export/ civil side colour 13 b. export/ equi side
colour 15
c. export/ stru side colour 16
d. export finish
1. For Undo Command
a. MDB NOUPDATE
b. EXIT 1. Mdb Update
a. MDB UPDATE
b. USER PROMQAMQA/MQA
c. /SUFN
d. EXIT 1. UNCLAIM CE
2. UNCLAIM ALL
3. ALPHA REQ CLEAR (To clear the command screen)
4. CREATE NEW ZONE/SITE/EQUI 5. ADD ALL WITHIN VOL CE 100 6. Q
ORI (To see the orientation)
7. ALPHA LOG /C:/ANANT.TXT (To make command line file)
8. SAVEWORK
9. Q US (User name)
10. Q MDB (Multiple data base)
11. Q REF
12. RECREATE DISPLAY /ABC.TXT (For save Display)
13. $M ABC.TXT (For restore Display)
1) ORI AND P3 IS TO IDP@
2) ORI P3 IS TO IDP@
3) DIR AND P3 IS U, D, N, E, W, S
Piping
ADD ALL PIPE WITHIN VOL CE 500If you put it at Branch level, all
pipe elements around the branch will be displayed.
ADD ALL PANEL WITHIN VOL CE 300If you put it at Branch level,
all panel elements around the branch will be displayed.
ADD ALL WITHIN VOL CE 400If you put it at Branch level, all
elements around the branch will be displayed.
CONNCurrent element will get connected.
Q DTXR
AXES AT PTTo know the Tail point
AXES AT PHTo know the Head point
ADD ALL PIPE WITH MATCHWILD(NAME,'*577037*') COL2
Q MATREF To query the Material Specification
Q DESPTo query the Design Parameter of the Equipment
Q MTXXTo query the Material of the component
Q PATOPTo query the Top of the Pipe co-ordinates
Q PA BOPTo query the Bottom of the Pipe co-ordinates
Q HDIRTo query the Head direction
Q TDIRTo query the Tail direction
ADD HREFTO ADD PIPE ATTACHED TO HEAD OF CURRENT BRANCH
ADD TREFTO ADD PIPE ATTACHED TO TAIL
ADD HREF TREFTo add PIPE attached to both HEAD and TAIL of
current branch
HPOSI ENU. WRT /*To change the position of head WRT to WORLD
VAR 1 NAME
VAR 2 WORPOSTo mark the component name
AIS TEXT '$V1' AT $V2
new bend copy prev conn dir uFor copying a existing bend to new
bend
q att (select bend)Edit the radius and bend angle
Q DDNM
AT CREFKeep it at CREF
ADD CREFAdd Connected Reference item
CONNECT BWDTo connect backward
Q ANGLTo find the angle of the component
NEW ELBO CHOOSETo create a new elbow
DIR TO NEXTTo move the component in the direction of next
componenet
FLIPTo rotate w.r.t its own axis
BACKTo change the direction from Forward to Backward
THRO CREFPlace it at CREF
THRO ID@Place it at the place, where it has been selected by
Mouse click
THRO NEXTPlace it at the next component
CREF ID@Be at the place, click the item to be included as
CREF
CHOOS ALLAll the available types of that particular components
will be listed
NEW TEE CHOOS ALLNew Tee can be created from the list of all
types of Tee for that spec.
GOTO CATREFGo to Catalogue Reference
Q TUCLTo find out the length of Branch
Q MTCLTo find out the length of Branch
INCLUDE ID BRANCH @To move a branch from one line to another
line
PREC OUT DI 4 DECTo get 4 Decimal precision on Co-ordinate
values.
FCONNForced connection
Q TPOSQuery Tail Position
Q HPOSQuery Head Posion
STATUSWill give us the list of DBs and and the access rights for
the User & Module
$QTo Query the list of commands available
Q DTXRTo get detailed description of a component
Q MTXXTo get material of construction of a piping element
DRAG MOVE S DIST 1000The current element and the constrained
network are moved south bythespecified distance.
DRAG AT E 3000The current element and the constrained network
will be dragged to the specified position.
DRAG MOVE E 3000The current element and the constrained network
will be moved to the specified position.
ORI AND P3 IS TO IDP@TO ORIENTATE THE LEAVE POINT OF TEE TO THE
REQUIRED DESIGN ELEMENT
Q BRWEITo get the weight of the selected component
NEW TEE CHOOS ALLNew Tee can be created from the list of all
types of Tee for that spec.
Q SPREFSpecification Reference
Q DESPQuery the Design Parameter
CH CETo check the Data Inconsistency
Q SPEC OF BRANQuery the Specification of Piping branch
Q SPEC OF SPREFQuery the Specification reference of Piping
branch
Q HBOREQuery the head bore details of the branch component
Q TBOREQuery the tail bore details of the branch component
Q DXTRQuery the description of the component
Q ISPEC (ex: ISPEC ADD or ISPEC REMOVE)Query the requirement of
the Insulation
Q PSPEQuery the Piping Specification
FOR NOZZLE ORIENTATIONNOZZLE ORRIENTION TEXTBtext
'#NAME(P2:)(C2:);#SPRE(P2:)(C6:11)#SPRE(P2:)(C12:)'Btext
'#NAME(P2:)(C2:)'Btext '#EQUI(C2:)#/#POS'Pltxt '~C OF
FIXED#/SADDLE'Pltxt '~C OF SLIDING#/SADDLE'Pltxt 'BOTTOM OF BASE
PLATE#/EL.#P6POSU(C2:)'Pltxt 'PLTF.EL.#DIMPOSU(C2:)'Pltxt
'B.TL.'Btext '##/2Nos.180~0 APPART.'Btext '##/BOP. EL.#PABOPU(C2:)'
FOR INCH YOU HAVE GIVE PIPE NAME
Btext '##/CON.RED' THIS IS FOR REDUCER
Btext '#P5POSN' this is for chaning wrt to site coordinet
Title'VENT STACK AREA#>#/RABAR RGMS' THIS IS FOR TITLE
EDIT
Btext '##/ (TYP)' FOR SPEC. TYP
Pltxt '#DSCO#>#/BOP. EL.#PABOPU(C2:)'
Pltxt #P1POSE (PUT P4 FROM EAST, P5 FROM NORTH, P1 TO EAST AND
P2 TO NORTH COORDINATE)
