Upload
vuongcong
View
300
Download
31
Embed Size (px)
Citation preview
COLOR MONITORSERVICE MANUAL
Website:http://biz.LGservice.comE-mail:http://www.LGEservice.com/techsup.html
CAUTIONBEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
MENU SELECT
MODEL: StudioWorks 563N (CB563G-NA), StudioWorks 563A (CB563G-AA),(CB563G-NJ)MT533 (MT563 Rev A), STONE563 (CB563G-NK),563Si (563Si Rev A), HG563 (HG563 Rev A)
CHASSIS NO. : CA-112FACTORY MODEL: CB563G
*( ) ID LABEL Model No.
1. PICTURE TUBE Size : 15 inch (Flat Square Tube)DefIection Angle : 90°Neck Diameter : 29.1 mmDot Pitch : 0.28 mmFace Treatment : AR-ASC (Anti-Reflection and
Anti-Static Coating)Low Radiation : MPR-II
2. SIGNAL2-1. Horizontal & Vertical Sync
1) Input Voltage Level : Low= ≤0.8V, High= ≥2.0V2) Sync Polarity : Positive or Negative
2-2. Video Input Signal1) Voltage Level : 0 ~ 0.7 Vp-pa) Color 0, 0 : 0 Vp-pb) Color 7, 0 : 0.467 Vp-pc) Color 15, 0 : 0.7 Vp-p
2) Input Impedance : 75 Ω3) Video Color : R, G, B Analog4) Signal Format : Refer to the Timing Chart
2-3. Signal Connector15-pin D-Sub Connector (Attached Type)
2-4. Scanning FrequencyHorizontal : 30 ~ 61 kHzVertical : 50 ~ 120 Hz
3. POWER SUPPLY3-1. Power Range
AC 100~240V (Free Voltage), 50/60Hz, 1.5A Max.
3-2. Power Consumption
4. DISPLAY AREA4-1. Active Video Area :
• 285 x 215 mm (11.22" x8.46") - Max Image Size• 270 x 200 mm (10.63" x 7.87") - Preset Image Size
4-2. Display Color : Full Colors4-3. Display Resolution : 1024 x 768 / 75Hz
(Non-Interlace)4-4. Video Bandwidth : 78 MHz
5. ENVIRONMENT5-1. Operating Temperature: 0°C ~ 40°C
(Ambient)5-2. Relative Humidity : 10%~ 90%
(Non-condensing)5-3. Altitude : 3,000 m
6. DIMENSIONS (with TILT/SWIVEL)Width : 356.0 mm (14.01")Depth : 395.0 mm (15.55")Height : 371.0 mm (14.60")
7. WEIGHT (with TILT/SWIVEL)Net Weight : 11.7 kg (25.79 lbs)Gross Weight : 13.2 kg (29.10 lbs)
CONTENTS
- 2 -
SPECIFICATIONS ................................................... 2SAFETY PRECAUTIONS ........................................ 3TIMING CHART ....................................................... 4OPERATING INSTRUCTIONS ................................ 5WIRING DIAGRAM ................................................. 6BLOCK DIAGRAM ................................................... 7DESCRIPTION OF BLOCK DIAGRAM................... ..8
ADJUSTMENT ........................................................ 9TROUBLESHOOTING GUIDE .............................. 11EXPLODED VIEW................................................... 21REPLACEMENT PARTS LIST ............................... 23PIN CONFIGURATION........................................... 28SCHEMATIC DIAGRAM......................................... 30PRINTED CIRCUIT BOARD................................... 32
SPECIFICATIONS
MODE
NORMAL (ON)
STAND-BY
SUSPEND
OFF
H/V SYNC
ON/ON
OFF/ON
ON/OFF
OFF/OFF
POWER CONSUMPTION
less than 63 W
less than 15 W
less than 15 W
less than 5 W
LED COLOR
GREEN
AMBER
AMBER
SAFETY-RELATED COMPONENT WARNING!There are special components used in this color monitorwhich are important for safety. These parts are marked
on the schematic diagram and the replacementparts list. It is essential that these critical parts should bereplaced with the manufacturer's specified parts toprevent X-radiation, shock, fire, or other hazards. Do notmodify the original design without obtaining writtenpermission from manufacturer or you will void the originalparts and labor guarantee.
CAUTION: No modification of any circuit should beattempted.Service work should be performed only afteryou are thoroughly familiar with all of thefollowing safety checks and servicingguidelines.
SAFETY CHECKCare should be taken while servicing this color monitorbecause of the high voltage used in the deflection circuits.These voltages are exposed in such areas as theassociated flyback and yoke circuits.
FIRE & SHOCK HAZARDAn isolation transformer must be inserted between the
color monitor and AC power line before servicing thechassis.
• In servicing, attention must be paid to the original leaddress specially in the high voltage circuit. If a shortcircuit is found, replace all parts which have beenoverheated as a result of the short circuit.
• All the protective devices must be reinstalled per theoriginal design.
• Soldering must be inspected for the cold solder joints,frayed leads, damaged insulation, solder splashes, orthe sharp points. Be sure to remove all foreignmaterials.
IMPLOSION PROTECTIONAll used display tubes are equipped with an integralimplosion protection system, but care should be taken toavoid damage and scratching during installation. Use onlysame type display tubes.
X-RADIATIONThe only potential source of X-radiation is the picture tube.However, when the high voltage circuitry is operatingproperly there is no possibility of an X-radiation problem.The basic precaution which must be exercised is keep thehigh voltage at the factory recommended level; the normalhigh voltage is about 24.5kV. The following steps describehow to measure the high voltage and how to prevent X-radiation.
Note : It is important to use an accurate high voltage meter calibrated periodically.
• To measure the high voltage, use a high impedance high voltage meter, connect (–) to chassis and (+) tothe CDT anode cap.
• Set the brightness control to maximum point at fullwhite pattern.
• Measure the high voltage. The high voltage metershould be indicated at the factory recommended level.
• If the meter indication exceeds the maximum level,immediate service is required to prevent the possibilityof premature component failure.
• To prevent X-radiation possibility, it is essential to usethe specified picture tube.
CAUTION:Please use only a plastic screwdriver to protect yourselffrom shock hazard during service operation.
SAFETY PRECAUTIONS
- 3 -
TIMING CHART
- 4 -
VIDEO
SYNC
C E
DF
AB
* Mode 1~Mode 4: Basic Mode
H – 37.50 26.67 20.32 6.35 2.03 3.81 0.51
V – 74.99 13.335 12.802 0.533 0.080 0.427 0.026
H + 46.88 21.33 16.16 5.17 1.62 3.23 0.32
V + 75.01 13.331 12.798 0.533 0.064 0.448 0.021
H + 53.68 18.63 14.22 4.41 1.14 2.70 0.57
V + 85.07 11.755 11.178 0.577 0.056 0.503 0.018
H + 60.020 16.660 13.000 3.660 1.220 2.240 0.200
V + 75.030 13.328 12.795 0.533 0.050 0.466 0.017
Mode H/VSort
1
2
3
4
640x48075Hz
800x60085Hz
1024x76875Hz
800x60075Hz
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>
SyncPolarity Frequency
Total Period(E)
Video Active Time (A)
Sync Duration(D)
Blanking Time(B)
Back Porch(F)
Front Porch(C) Resolution
- 5 -
OPERATING INSTRUCTIONS
MENU SELECT
FRONT VIEW REAR VIEW
AC Power Socket Signal Connector
ID Label
Power ON/OFF ButtonSee Front Control Panel
Front Control Panel
1. Power ON/OFF ButtonUse this button to turn the monitor on or off.
2. Power IndicatorThis indicator lights up green when the monitor operatesnormally; in DPMS (Energy Saving) mode, - stand-by,suspend, or power off mode - its color changes to orange,and if abnormal or damaging circuit turns out orange blink.
3. SELECT ButtonUse this button to enter a selection in the on screen display.
4. SET ButtonUse these buttons to choose or adjust items in the onscreen display.
5. MENU ButtonUse this button to enter or exit the on screen display.
MENU SELECT
1345 2
WIRING DIAGRAM
- 6 -
P501
P301P302
G2
P702
P701
T1
P402
P902
S+
S
Signal Cable
AC Socket
FB
T
BLOCK DIAGRAM
- 7 -
ME
NU
SE
LEC
TP
OW
ER
PO
WE
R IN
PU
T10
0~24
0VA
C(5
0/60
Hz)
Line
Filt
er
Deg
auss
ing
Circ
uit
< O
SD
Con
trol
>
SM
PS
TR
AN
S(T
901)
SM
PS
CO
NT
RO
L(I
C90
1)
DP
MC
ON
TR
OL
CIR
CU
IT
Vol
tage
Reg
ulat
ing
Circ
uit
80V
50V
15V
6.3V
TIL
TO
PT
ION
Con
trol
Circ
uit
6.3V
15V
E2 P
RO
M(I
C40
2)
H /
V P
OS
ITIO
N
BR
IGH
TN
ES
SC
ON
TR
AS
T
H /
V S
IZE
INF
OR
MA
TIO
NS
PC
CT
RA
PE
ZO
IDP
IN B
ALA
NC
EP
AR
ALL
ELO
GR
AM
RE
CA
LLD
EG
AU
SS
OS
D T
IME
CO
LOR
CU
RV
EM
OIR
ELA
NG
UA
GE
RE
SE
TV
IDE
O L
EV
EL
5V
OS
D IC
(IC
301)
MT
V03
8-15
H-S
ync
Sig
V-S
ync
Sig
I2C
DA
TA
(SD
A)
I2C
CLO
CK
(SC
L)
VID
EO
LM12
69
PR
E-A
MP
(IC
302)
Sig
nal
Cab
leR G B
VID
EO
LM24
68
LM24
80
CU
T O
FF
IC
(IC
304)
MA
IN A
MP
(IC
303)
5V
5V
H/V
Syn
c P
roce
ssor
( IC
701
)T
DA
4857
V-O
UT
( IC
601)
TD
A48
66
H-O
UT
( Q
706)
H-L
inea
rity
Cor
rect
ion
DC
/DC
Con
vert
er
X-R
AY
Pro
tect
ion
Circ
uit
FB
T(
T70
1 )
Aut
oB
eam
Lim
it
Ver
tical
Bla
nkin
g,B
right
ness
Con
trol
- 16
0V
40V
ST
EP
UP
15V
D/D
Fee
d B
ack
15V
MIC
OM
(IC
401)
SC
L / S
DA
H/V
Syn
c,P
WM
Con
trol
15V
5V15
V
80V
15V
50V
DY
CD
T
Hea
ter
( 6.
3V )
I2C
I2C
I2C
H/V
Syn
c
G1Screen(G2)
Static Focus
H.V
R/G
/BD
rive/
Con
tras
tC
ut-O
ff
H-D
RV
B-D
RV
B+
15V
TILT COIL
DEGAUSSINGCOIL
I2C
Vou
t 1
Vou
t 2
DESCRIPTION OF BLOCK DIAGRAM
1. Line Filter & Associated Circuit.This is used for suppressing noise of power input lineflowing into the monitor and/or some noise generated inthis monitor flowing out through the power input line.That is to say, this circuit prevents interference betweenthe monitor and other electric appliances.
2. Degauss Circuit & Coil.The degauss circuit consists of the degaussing coil, thePTC(Positive Temperature Coefficient) thermistor(TH901),and the relay(RL901). This circuit eliminates abnormalcolor of the screen automatically by degaussing theshadow mask in the CRT during turning on the powerswitch. When you need to degauss in using the monitor,select DEGAUSS on the OSD menu.
3. SMPS(Switching Mode Power Supply).This circuit is working of 90~264V AC(50/60Hz).The operation procedure is as follows:1) AC input voltage is rectified and smoothed by the
bridge diodes (D900) and the capacitor (C908).2) The rectified voltage(DC) is applied to the primary
coil of the transformer(T901).3) The control IC(IC901) generates switching pulse to
turn on and off the primary coil of the transformer(T901) repeatedly.
4) Depending on turn ratio of the transformer, thesecondary voltages appear at the secondary coils ofthe transformer(T901).
5) These secondary voltages are rectified by eachdiode(D941, D942, D951, D961, D962, D971) andoperate other circuit. (horizontal and verticaldeflection, video amplifier, ...etc.)
4. X-ray Protection.If the high voltage of the FBT reaches up to 29kV (abnormalstate), IC401(MICOM) pin 35 Sensing from FBT directly.Then MICOM control IC701 (Deflection controller) to stopHorizontal drive pulse and stop Horizontal Deflection.
5. Micom(Microprocessor) Circuit.The operating procedure of Micom(Microprocessor) andits associated circuit is as follows:
1) H and V sync signal is supplied from the signal cable.2) The Micom(IC401) distinguishes polarity and
frequency of H and V sync.3) The Micom sets operating mode and offers the
controlled data. (H-size, H-position, V-size, ... etc.)4) The controlled data of each mode is stored in itself.5) User can adjust screen condition by each OSD
function. The data of the adjusted condition is storedin EEPROM(IC402).
6. Horizontal and Vertical Oscillation.This circuit generates the horizontal pulse and the verticalpulse by taking the H and V sync signal.This circuit consists of the TDA4866(IC601) and theassociated circuit.
7. D/D(DC to DC) Converter.This circuit supplies DC voltage to the horizontal deflectionoutput circuit by increasing DC 50V which is thesecondary voltage of the SMPS in accordance with theinput horizontal sync signal.
8. Side-Pincushion & Trapezoid Correction Cirucit.This circuit improves the side-pincushion and thetrapezoid distortion of the screen by mixing parabola andsaw-tooth wave to output of the horizontal deflection D/Dconverter which is used for the supply voltage(B + ) of thedeflection circuit.
9. Horizontal Deflection Output Circuit.This circuit makes the horizontal deflection by supplyingthe saw-tooth current to the horizontal deflection yoke.
10. High Voltage Output & FBT(Flyback Transformer).The high voltage output circuit is used for generating pulseto the primary coil of the FBT(Flyback Transformer(T701)).A boosted voltage(about 24.5kV) appears at thesecondary of the FBT and it is supplied to the anode,focus, and screen voltage of the CRT.
11. H-Linearity Correction Circuit.This circuit corrects the horizontal linearity for eachhorizontal sync frequency.
12. Vertical Output Circuit.This circuit takes the vertical ramp wave from theTDA4857(IC701) and performs the vertical deflection bysupplying the saw-tooth current to the vertical deflectionyoke.
13. H & V Blanking and Brightness Control.Blanking circuit eliminates retrace line by supplyingnegative pulse to the G1 of the CRT. And Brightnesscircuit is used for control of the screen brightness bychanging DC level of the G1.
14. Image Rotation (Tilt) Circuit.This circuit corrects the tilt of the screen by supplying theimage rotation signal to the tilt coil which is attached nearthe deflectithe deflection yoke of the CRT.
15. Video Pre-Amp Circuit.This circuit amplifies the analog video signal from 0-0.7Vto 0-4V. It is operated by taking the clamp, R, G, B driveand contrast signal from the Micom(IC401).
16. Video Output Amp Circuit.This circuit amplifies the video signal which comes fromthe video pre-amp circuit and amplified it to applied theCRT cathode.
- 8 -
- 9 -
ADJUSTMENT
GENERAL INFORMATION
All adjustment are thoroughly checked and correctedwhen the monitor leaves the factory, but sometimesseveral adjustments may be required. Adjustment should be following procedure and afterwarming up for a minimum of 30 minutes.
• Alignment appliances and tools.- IBM compatible PC.- Programmable Signal Generator.
(eg. VG-819 made by Astrodesign Co.)- EPROM or EEPROM with saved each mode data.- Alignment Adaptor and Software.- Digital Voltmeter.- White Balance Meter.- Luminance Meter.- High-voltage Meter.
AUTOMATIC AND MANUAL DEGAUSSINGThe degaussing coil is mounted around the CDT so thatautomatic degaussing when turn on the monitor. But amonitor is moved or faced in a different direction, becomepoor color purity cause of CDT magnetized, then pressDEGAUSS on the OSD menu.
ADJUSTMENT PROCEDURE & METHOD- Install the cable for adjustment such as Figure 1and run
the alignment program on the DOS for IBM compatible PC. - Set external Brightness and Contrast volume to max position.
1. Adjustment for B+ Voltage.1) Display cross hatch pattern at Mode 4.2) Check C961 (+) voltage to 50± 0.5Vdc.
2. Adjustment for High-Voltage. 1) Display cross hatch pattern at Mode 4.2) DIST.ADJ→CTRL PWM → High Voltage Command.3) Adjust High Voltage to 24.5kV±0.1 kVdc.4) Press Enter Key.
3. Adjustment for Factory Mode (Preset Mode).1) Display cross hatch pattern at Mode 1.2) Run alignment program for CB563G on the IBM
compatible PC.3) EEPROM → ALL CLEAR → Y(Yes) command.
<Caution> Do not run this procedure unless the EEPROM is changed. All data in EEPROM (mode data and color data) will be erased.
4) Power button of the monitor turn off → turn on.5) COMMAND→PRESET START→Y(Yes) command.6) DIST. ADJ. → CTRL PWM → TILT command.
7) Adjust tilt as arrow keys to be the best condition.8) DIST. ADJ. → BALANCE command.9) Adjust parallelogram as arrow keys to be the best
condition. 10) Adjust balance of pin-balance as arrow keys to be
the best condition.11) DIST. ADJ. → FOS. ADJ command.12) Adjust V-SIZE as arrow keys to 230±2mm.13) Adjust V-POSITION as arrow keys to center of the
screen.14) Adjust H-SIZE as arrow keys to 310±2mm.15) Adjust H-POSITION as arrow keys to center of the
screen.16) Adjust S-PCC (Side-Pincushion) as arrow keys to be
the best condition.17) Adjust TRAPEZOID as arrow keys to be the best
condition.18) Save of the Mode 1.19) Display from Mode 2 to 4 and repeat above from
number 12) to 19)20) PRESET EXIT → Y (Yes) command.
4. Adjustment for White Balance and Luminance.1) Set the White Balance Meter.2) Press the DEGAUSS on the OSD menu for
demagnetization of the CDT.3) COLOR ADJ. → LUMINANCE command of the
alignment program.4) Set Brightness and Contrast to Max position.5) Display color 0,0 pattern at Mode 4.6) COLOR ADJ.→ BIAS ADJ.→ COLOR No. → 1
command of the alignment program.7) Check whether green color or not at R-BIAS and G-
BIAS to min position and B-BIAS to 127(7F) andSub-Brightness to 177(B1) position. Adjust G2(screen) command to 0.4± 0.05FL of the rasterluminance.
8) Adjust R-BIAS and G-BIAS command to x=0.283±0.005 and y=0.298±0.005 on the White BalanceMeter with PC arrow keys.
9) Adjust SUB-Brightness command to 0.4±0.1FL of theraster luminance.
10) Adjust repeat number 8).11) After push the “ENTER” key.
11-1) COMMAND → PRESET START → Y(Yes) command.12) Display color 15,0 full white pattern at Mode 4.13) DRIVE ADJ.→ No 1. command.
- 10 -
14) Set Brightness and Contrast to Max position.15) Set SUB-CONTRAST Max 127(7F) (decimal) position.16) Set B-DRIVE to 100(64) at DRIVE of the alignment
program.17-1) Adjust R-DRIVE and G-DRIVE command to white
balance x=0.283±0.003 and y=0.298±0.003 on theWhite Balance Meter with PC arrow keys.
17-2) Display color 15,0 window pattern (70x70mm) at mode 4.18) Adjust SUB-CONTRAST command to 50±2FL .19) Display color 15,0 full white patten at Mode 4.20) Set Brightness and Contrast to Max position.21) COLOR ADJ. → LUMINANCE → ABL command.22) Adjust ABL to 32±1FL of the luminance.23) After push the “ENTER” key, and “COMMAND →
PRESET EXIT → Y(Yes)” command.24) Exit from the program.
5. Input EDID Data.1) Display color 15,0 cross hatch pattern at Mode 4.2) EEPROM → Write EDID command and confirm
“EDID Write OK!!” message of monitor.3) Exit from the alignment program.4) Power switch OFF/ON for EDID data save.
6. Adjustment for Focus.1) Set the Brightness and Contrast to max position.2) Display H character in full screen at Mode 4.3) Adjust two Focus control on the FBT that focus
should be the best condition.
- 11 -
TROUBLESHOOTING GUIDE
NO POWER(POWER INDICATOR OFF)
TROUBLE IN D900
TROUBLE IN FUSE(F901)
TROUBLE IN IC901
TROUBLE IN D941, D942, D951, D961, D962, D971
TROUBLE IN
Q903, Q952,
Q951, Q942, Q941
CHECKFUSE OK?
(F901)
CHECKC908 VOLTAGE?
(AC120V: 160VDC,AC220V: 304VDC)
NO
YES
YES
YES
YES
NO
NO
NO
CHECKIC901 PIN 6WAVEFORM
(SQUARE WAVE COMES OUT?)
CHECKD941, D942, D951,D961, D962, D971
VOLTAGE?
1. NO POWER
- 12 -
2. NO CHARACTER
NO CHARACTER
CHECKIC302
PIN 9 (5V) ?
CHECK IC302 PIN 5, 6, 7 ?
CHECK IC302 PIN 18, 19, 20 ?
CHECKIC303
PIN 1, 2, 3 ?
CHECK IC303 PIN 4 (80V)
PIN 8 (12V) ?
TROUBLE IN P302 5V LINE
TROUBLE IN PC SIGNAL,P301 SIGNAL CABLE
TROUBLE IN IC302
TROUBLE IN P303 12V LINE/80V LINE
TROUBLE IN IC303
NO
YES
NO
NO
YES
YES
YES
YES
NO
NO
CHECK R, G, B CATHODE
VOLTAGE?
TROUBLE IN R331~R333,L311~L313D307~D312
TROUBLE INCRT SOCKET
YES
NO
- 13 -
NO VIDEO(POWER INDICATOR ON)
CHECK POWER INDICATORGREEN or ORANGE?
CHECKD712 ANODE
(-157V)?
CHECKG1 VOLTAGE?
(-55 ~ -15V)
TROUBLE IND712
TROUBLE IN Q799
DPM MODE(NO H and/or V SYNC)
ORANGE
NO
GREEN
YES
NO
3. NO RASTER
CHECKCDT HEAT
VOLTAGE? (6.3V)
TROUBLE IN D941, Q942, Q941
YES
NO
TROUBLE INCDT
YES
- 14 -
4. NO HORIZONTAL DEFLECTION
NO H-DEFLECTION(ONE VERTICAL LINE)
CHECKQ706?
CHECK B+ VOLTAGE
(50V)?
CHECKT701(FBT) PIN 2
(31KHZ, 60V69KHZ, 140V ?
CHECK Q701 COLLECTOR
WAVEFORM?
TROUBLE IN Q706
TROUBLE IN50V LINE
TROUBLE INQ719, Q720, D710
TROUBLE INQ701
TROUBLE INT701, P701
NO
NO
YES
YES
YES
YES
NO
NO
0VT
- 15 -
5. TROUBLE IN H-LINEARITY
UNBALANCED OF H-LIN.
CHECKIC401
PIN 5, 6, 7 ?
CHECK Q711~Q716?
CHECK L703?
TROUBLE IN IC401 (MICOM)
TROUBLE INQ711 ~ Q716
TROUBLE INL703
TROUBLE INC722, C723, C726, C729
NO
NO
NO
YES
YES
YESCs SIGNAL TABLE
HORIZONTALFREQUENCY(fH)
30K ~ 33.9K34K ~ 38.9K39K ~ 44.9K45K ~ 48.9K49K ~ 57.9K58K ~ 65.9K66K ~ 70K
Cs1
LLHLHLH
Cs3
LLLHHHH
Cs2
LHHLLHH
- 16 -
6. NO VERTICAL DEFLECTION
NO V-DEFLECTION(ONE HORIZONTAL LINE)
CHECKIC601 PIN 3
(15V)?
CHECK IC601 PIN 7
(40V)?
CHECKIC701 PIN 12, 13?
TROUBLE IN R603 15V LINE
TROUBLE INHIGH-VOLTAGE OUTCIRCUIT(FBT), D721, R606
TROUBLE INIC701
TROUBLE INIC601, V-CIRCUIT
NO
NO
YES
YES
YES
NO
3V
- 17 -
TROUBLE INOSD PERIPHERALCIRCUIT
NO OSD
TROUBLE IN 5V LINE
TROUBLE INIC601 PIN8 (V-FBP),T701 40V LINE (H-FBP)
TROUBLE INIC302, IC301
TROUBLE INIC301, IC302
NO
YESDC 5V
YES
YES
YES
NO
NO
NO
Pin 55V
Pin 10
5V
H+V
5V
H+V
CHECKIC301 B+ ?
CHECKIC301 PIN 12
WAVEFORM ?
(ENTER BUTTON MUST BE PRESSED.)
7. TROUBLE IN OSD
CHECKIC301 PIN 5, 10 WAVEFORM?
CHECKIC301 PIN 13, 14, 15 ?
- 18 -
CHECK IC401 (MICOM)
PIN 31, 32 (H/V INPUT)SIGNAL?
CHECK IC401 PIN 13 WAVEFORM?
CHECK IC401 (MICOM)
PIN 2, 3 ?
CHECK B+ LINE
(6.3V,15V, 80V) ?
CHECK PC,(PC IS NOT GOING INTODPM OFF MODE)
TROUBLE INX401
TROUBLE INIC401 (MICOM)
TROUBLE INQ941, Q942, Q951, Q952,
TROUBLE IN PC
OFF MODE FAILURE
INPUT H/V SYNC SIGNAL
H/V SYNC
(NO OFF MODE.)
NO
NO
NO
NO (DPMF: 0V)
DPM TABLE
Mode Item
NORMAL
STAND-BY
SUSPEND
OFF
DPMF
H
H
H
L
LED
GREEN
AMBER
AMBER
AMBER
DPMS
H
L
L
L
YES
YES
SEE DPM TABLE
YES
YES
8. TROUBLE IN DPM
5V
24MHz
- 19 -
CHECK IC401 PIN 19
(0V)?
CHECK Q953 COLLECTOR
VOLTAGE?
CHECK P902 ?
CHECK RL901?
TROUBLE IN IC401 (MICOM)
TROUBLE INQ953
TROUBLE INP902
TROUBLE INRL901
TROUBLE IN TH901, DEGAUSSING COIL
NO DEGAUSSING
DC 15V
NO
NO
NO
NO
YES
YES
YES
YES
(DEGAUSS ON THE OSD MENU MUST BE PRESSED.)
9. NO DEGAUSSING
- 20 -
10. NO TILT (NO ROTATION)
NO TILT (NO ROTATION)
TROUBLE IN IC401 (MICOM)
TROUBLE IN15V LINE, 6.3V LINE
TROUBLE INQ501~Q503
TROUBLE INP501, TILT COIL, D501
NO
YES
YES
YES
CHECK15V LINE
AND 6.3V LINE ?
CHECKQ503 EMITTER
VOLTAGE ?
NO
NO
CHECKIC401 PIN 21
WAVE FORM ?
EX
PL
OD
ED
VIE
W
- 21 -
10
A
MEN
U
SELE
CT
12
1
4
12
12
3
2
6
5
8
B
7
9
11-1
11-2
a
b
cb
EXPLODED VIEW PARTS LIST
- 22 -
Ref. No.
1
2
3
4
5678910
11-111-212
A
B
abc
Part No.3091TKB036D
3091TKB036A
3091TKB036B
3091TKB036E
3091TKB036M
3091TKB036L
3091TKB036H
3091TKB036K
3091TKB036G
3091TKB036J
2423GB0A8AW
2423GB0A8AX
2423GB0A8CF
2423GB0A59A
3809TKB021A
3809TKB021D
3809TKB021E
3809TKB021G
3809TKB021F
3043TKK071B
3043TKK071G
3043TKK071H
339-002D
150-A29W
6174Z-1035G
6620TKB002B
6850TA9004A
4950TKS155D
4810TKK151A
4810TKK150A
332-102F
3313T15081F
3313T15081J
3313T15081G
3313T15081H
3313T15081E
3313T15081L
3313T15081M
6871TMT289F
6871TMT289J
6871TMT289G
6871TMT289H
6871TMT289E
6871TMT289L
6871TMT289M
332-112F
4001TKK004E
339-008C
Description
CABINET ASS’Y, CB563C BRAND B031 LGEIL ABS 85964 -For Word Wide (CB563G-NA)
CABINET ASSEMBLY, CB563 BRAND B031 CB563 ABS 85964 -For Brazil, Mexico: (CB563G-NA)
CABINET ASSY, CB563C BRAND B031 S/W563A ABS85964 -For Brazil, Mexico, Panama: (CB563G-AA)
CABINET ASS’Y, CB563C BRAND B031 S/W563A 320T 85964 -For Word Wide(CB563G-AA)
CABINET ASS’Y, CB563C MICROTOUCH B031 320T 85964 - (MT563 Rev A)
CABINET ASS’Y, CB563C OMEGA B031 AF320T 12218 - (CB563G-NK)
CABINET ASS’Y, CB563C HI-GRADE B031 12218 320T - (HG563 Rev A)
CABINET ASS’Y, CB563C TIME B031 85964 320T - (563Si Rev A)
CABINET ASS’Y, CB563C NO BRAND B031 320T 85964 - (CB563G-NJ)
CABINET ASS’Y, CB563C B024 TINY 15448 320T - (563N Rev A)
CDT(CIRC), M36LBL803X 31NLLA LG-PHILIPS Displays 54KHZ 29.1 m - For Northern Hemisphere: (CB563G-NA)
CDT(CIRC), M36LBL803X 31RLLA LG-PHILIPS - For Brazill, S.Africa: (CB563G-NA), Panama : (CB563G-AA)
CDT(CIRC), M36LBL803X 31NLLM LG-PHILIPS Displays 54KHZ 29.1 mm -For Equatorial: (CB563G-NA)
CDT(CIRC), M36LBL503X 34RLLD LG-PHILIPS Displays 54KHZ 29.1 mm -For Equatorial: (CB563G-AA)
BACK COVER ASS’Y, CB563 B024 ABS 85964 - (CB563G-NA), (CB563G-AA)
BACK COVER ASS’Y, CB563C B024 NO BRAND 85964 320T - (MT563 Rev A), (CB563G-NJ)
BACK COVER ASS’Y, CB563C B024 HI-GRADE 12218 320T - (CB563G-NK), (HG563 Rev A)
BACK COVER ASS’Y, CB563C B024 TIME 85964 320T - (563Si Rev A)
BACK COVER ASS’Y, CB563C B024 TINY 15448 320T - (563N Rev A)
TILT SWIVEL ASS’Y, KCB563C B046, T051 HIPS 85964 SP LOCAL
TILT SWIVEL ASS’Y, CB563C T051,B046 12218 LGEDI - (CB563G-NK), (HG563 Rev A)
TILT SWIVEL ASS’Y, CB563C B046 T051 15448 LGEDI - (563N Rev A)
SCREW ASS’Y, PHP+5*30BP(FZMY)+GW18
COIL,DEGAUSSING, LX31 GET 8.4 OHM, 0.4*70T, L870, WITH EARTH
FBT (FLY BACK TRANSFORMER), FMMTC81 AM1035G (LIM SANG IL)
SOCKET(CIRC), POWER, SA-4S HUA JIE AC UNIVERSAL 3PIN BLACK
CABLE,D-SUB, UL 2990-9C(7.5) AT 1560MM GLAY CB777G DM
METAL, SHIELD BOTTOM , CB563C(PEM NUT)
BRACKET, CN771C SUPPORTER BOT.(LEFT)
BRACKET, CN771C SUPPORTER BOT.(RIGHT)
SCREW, PTP+4*20BP(MSWR/FZMY)
MAIN TOTAL ASSEMBLY, CB563G.XLVMD BRAND CA-112 - For Word Wide: (CB563G-NA)
MAIN TOTAL ASSEMBLY, CB563G.KXIDML BRAND CA-112 -For India: (CB563G-NA)
MAIN TOTAL ASSEMBLY, CB563G.KQLBMS BRAND CA-112 -For Brazil: (CB563G-NA)
MAIN TOTAL ASSEMBLY, CB563G.KQLBAS BRAND CA-112 -For Brazil: (CB563G-AA)
MAIN TOTAL ASSEMBLY, CB563G BRAND CA-112 -For Panama, Mexico: (CB563G-AA)
MAIN TOTAL ASSEMBLY, CB563G KQLHAD BRAND CA-112 - For Word Wide: (CB563G-AA)
MAIN TOTAL ASSEMBLY, CB563G KQLSMD BRAND CA-112 - For S.Africa: (CB563G-NA)
PWB(PCB) ASSEMBLY, MAIN, CB563G KXLVMD BRAND CA-112 TOTAL -For Word Wide: (CB563G-NA)
PWB(PCB) ASSEMBLY, MAIN, CB563G KXIDML BRAND CA-112 TOTAL -For India: (CB563G-NA)
PWB(PCB) ASSEMBLY, MAIN, CB563G KQLBMS BRAND CA-112 TOTAL -For Brazil: (CB563G-NA)
PWB(PCB) ASSEMBLY, MAIN, CB563G KQLBAS BRAND CA-112 TOTAL -For Brazil: (CB563G-AA)
PWB(PCB) ASSEMBLY, MAIN, CB563G KCLMMA BRAND CA-109 TOTAL -For Panama, Mexico: (CB563G-AA)
PWB(PCB) ASSEMBLY, MAIN, CB563G KQLHAD BRAND CA-112 TOTAL - For Word Wide: (CB563G-AA)
PWB(PCB) ASSEMBLY, MAIN, CB563G KQLSMD BRAND CA-112 TOTAL - For S.Africa: (CB563G-NA)
SCREW, DRAWING, D3.5 L10.0 MSWR/FZMY+SW3.5+RW3.5
SCREW ASSEMBLY, TAPTITE P TYPE D3.0 L10.0 MSWR/FZMY SW3+RW10
SCREW ASSY, MP+3*10(FZMY) + SW3+RW3
- 23 -
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C301 181-288N MKT 100V 103JTR PHS86103C302 0CE107CF638 “100UF SHL,SD 16V M FM5 TP”C303 0CK1040K945 0.1UF 50V Z F TRC304 0CK1030K945 0.01UF 50V Z F TRC305 0CE107CF638 “100UF SHL,SD 16V M FM5 TP”C306 181-288N MKT 100V 103JTR PHS86103C307 0CK3910K515 390P 50V K B TSC308 0CN1040K949 0.1M 50V Z F TA52C309 0CK1040K945 0.1UF 50V Z F TRC310 181-288B MKT 100V 104JTR PHS26104C311 0CK1040K945 0.1UF 50V Z F TRC312 0CN1040K949 0.1M 50V Z F TA52C313 0CK1040K945 0.1UF 50V Z F TRC314 0CC4700W405 47PF 500V J SL TPC315 0CE476CF638 “47UF SHL,SD 16V M FM5 TP 5”C316 0CK1010W515 100P 500V K B TSC317 0CN1040K949 0.1M 50V Z F TA52C318 0CK1040K945 0.1UF 50V Z F TRC319 0CN1040K949 0.1M 50V Z F TA52C320 0CK1040K945 0.1UF 50V Z F TRC321 0CE475CK638 “4.7UF SHL,SD 50V M FM5 TP”C322 0CN6810K519 680P 50V K B TA52C323 0CE476CF638 “47UF SHL,SD 16V M FM5 TP 5”C324 0CK1040K945 0.1UF 50V Z F TRC325 181-288B MKT 100V 104JTR PHS26104C326 0CE106CN638 “10UF SHL,SD 100V M FM5 TP”C327 181-288B MKT 100V 104JTR PHS26104C328 0CE106CN638 “10UF SHL,SD 100V M FM5 TP”C329 181-288B MKT 100V 104JTR PHS26104C330 181-288B MKT 100V 104JTR PHS26104C331 181-288G MKT 100V 334JTR PHS26334C332 181-288G MKT 100V 334JTR PHS26334C333 181-288G MKT 100V 334JTR PHS26334C334 181-288B MKT 100V 104JTR PHS26104C335 181-288B MKT 100V 104JTR PHS26104C336 181-288E MKT 100V 474JTR PHS 26474C339 0CK4710W515 470P 500V K B TSC340 0CK1040K945 0.1UF 50V Z F TRC341 0CK10302940 0.01M 2KV Z F SC342 0CE106CK638 “10UF SHL,SD 50V M FM5 TP 5”C346 0CK10202515 1000PF D 2KV 10% TR B(Y5P)C354 0CC0400K115 4P 50V D NP0 TSC355 0CC0400K115 4P 50V D NP0 TSC356 0CC0400K115 4P 50V D NP0 TSC357 0CE476CN618 47UF SHL 100V M FL TP5C358 0CK8210K515 820P 50V K B TSC372 0CK1040K945 0.1UF 50V Z F TRC401 0CN1040K949 0.1M 50V Z F TA52C402 0CE476CF638 “47UF SHL,SD 16V M FM5 TP 5”C403 0CK1040K945 0.1UF 50V Z F TRC404 0CC1800K415 18P 50V J NPO TPC405 0CC1800K415 18P 50V J NPO TPC406 0CK1010K515 100PF 50V K B TR
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C407 0CK1010K515 100PF 50V K B TRC408 0CK1040K945 0.1UF 50V Z F TRC409 0CC5600K415 56P 50V J NP0 TPC410 0CK1010K515 100PF 50V K B TRC411 0CK1040K945 0.1UF 50V Z F TRC412 0CK1040K945 0.1UF 50V Z F TRC413 0CK1040K945 0.1UF 50V Z F TRC601 0CE477EH618 470UF KMG 25V M FL TP 5C602 181-288B MKT 100V 104JTR PHS26104C603 0CE476CK638 “47UF SHL,SD 50V M FM5 TP 5”C604 181-288T MKT 100V 223KTR PHS85223C605 0CK1020W515 1000P 500V K B TSC701 0CQ5621N419 5600P 100V J POLY NI TPC702 0CZZTFT001M ECQB1H103JM3 103J 50V TP5.C703 0CZZTFT001Z ECQB1H104JM3 104J 50V TP5.C704 0CQ8221N519 0.0082U 100V K POLY NI TPC705 0CE476CF638 “47UF SHL,SD 16V M FM5 TP 5”C706 0CZZTFT001Z ECQB1H104JM3 104J 50V TP5.C707 0CZZTFT002B ECQV1H154JZ3 154J 50V TP5.C708 0CE227CH638 “220UF SHL,SD 25V M FM5 TP”C709 181-288P MKT 100V 153JTR PHS86153C711 0CQ5621N419 5600P 100V J POLY NI TPC713 0CQ1031N419 0.01U 100V J POLY NI TPC716 0CK2710K515 270P 50V K B TSC717 0CE105CN638 “1UF SHL,SD 100V M FM5 TP 5”C718 181-288D MKT 100V 473JTR PHS26473C719 0CZZTAB001A SM-BP(P)/BP 10UF 50V 13*25C720 0CK22101515 220P 1KV K B TP5C722 181-303H 394J 31.0*23.0*16.0*20.0 2C725 0CK10201515 1000P 1KV K B TSC726 181-482F 274JF 18.0*17.0*10.0*7.5 2C727 0CN1040K949 0.1M 50V Z F TA52C728 0CQ5621N419 5600P 100V J POLY NI TPC729 181-305V 514J 26.0*18.0*11.0*15.0 2C730 0CN1040K949 0.1M 50V Z F TA52C731 181-309P 512J 31.0*16.5*9.5*20.0 1.C732 0CQ1031N419 0.01U 100V J POLY NI TPC733 0CBZTBU003K 472J 20.0*13.0*8.0*10.0 80C737 0CK10102515 100PF 2KV K B TRC739 0CE226CK638 “22UF SHL,SD 50V M FM5 TP 5”C740 0CE227EL630 220UF KMG 63V M FM5 BULKC741 0CZZTFT002B ECQV1H154JZ3 154J 50V TP5.C742 0CZZTFT001R ECQB1H223JM3 223J 50V TP5.C743 0CK3310W515 330P 500V K B TSC744 0CE107CP630 100UF SHL 160V M FM5 BULKC746 0CK33101515 330P 1KV K B TSC747 0CK3320W515 3300P 500V K B TSC748 0CZZTFT002B ECQV1H154JZ3 154J 50V TP5.C749 0CE2256R638 2.2000UF SMS 250V M FM5 TPC750 0CK1040K945 0.1UF 50V Z F TRC751 181-288N MKT 100V 103JTR PHS86103C752 0CQ4721N419 0.0047U 100V J POLY NI TP5C754 0CC4700W405 47PF 500V J SL TPC755 0CK1040K945 0.1UF 50V Z F TR
REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.
* NOTE : S SAFETY MarkAL ALTERNATIVE PARTS
CAPACITORS
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C771 0CK10301510 0.01M 1KV K B SC773 0CE107CH638 “100UF SHL,SD 25V M FM5 TP”C774 181-288B MKT 100V 104JTR PHS26104C775 0CK2210K515 220P 50V K B TSC781 0CK1030K945 0.01UF 50V Z F TRC801 0CK1040K945 0.1UF 50V Z F TRC802 0CE106CK638 “10UF SHL,SD 50V M FM5 TP 5”C805 0CE106CK638 “10UF SHL,SD 50V M FM5 TP 5”C810 0CE106CK638 “10UF SHL,SD 50V M FM5 TP 5”C901 0CBZTBU002B BULK PCX2 335 474KC902 0CBZTBU002A BULK PCX2 335 224KC903 0CKZTTA003A SC E 222M 10.0FF7 250V TP7C904 0CKZTTA003A SC E 222M 10.0FF7 250V TP7C905 0CE476EK638 47UF KMG 50V M FM5 TP 5C906 0CK1520K515 1500P 50V K B TSC908 181-296K “150UF SMH,HC(25.4*30) 400V”C909 181-304T 273J 19.5*14.0*8.5*10.0 40C910 0CK33101515 330P 1KV K B TSC911 0CQ1021N419 1000P 100V J POLY NI TPC912 0CKZTTA003D SC SAMWHA 250V 1000F M TAPC913 0CKZTTA003D SC SAMWHA 250V 1000F M TAPC941 0CE108EF630 1000UF KMG 16V M FM5 BULKC942 0CE107CF638 “100UF SHL,SD 16V M FM5 TP”C943 0CK3310W515 330P 500V K B TSC944 0CKZTBU003C SC E 472M 14.0BW7 250V BK7C945 0CKZTBU003C SC E 472M 14.0BW7 250V BK7C951 0CE228CH630 2200U SHL 25V M FM5C952 0CE227CH638 “220UF SHL,SD 25V M FM5 TP”C953 0CE107CF638 “100UF SHL,SD 16V M FM5 TP”C954 0CE108ED618 1000UF KMG 10V M FL TP 5C971 0CE476EN618 47UF KMG 100V M FL TP 5C999 0CE227EL630 220UF KMG 63V M FM5 BULK
D201 0DL591000AA L-59BL/1EGW BK KINGBRIGHTD301 0DS141489AB 1N4148 TP GRANDE DO-34 500D302 0DS141489AB 1N4148 TP GRANDE DO-34 500D303 0DS141489AB 1N4148 TP GRANDE DO-34 500D304 0DS141489AB 1N4148 TP GRANDE DO-34 500D305 0DS141489AB 1N4148 TP GRANDE DO-34 500D306 0DS141489AB 1N4148 TP GRANDE DO-34 500D307 0DS124409AA 1SS244 TP ROHM KOREAD308 0DS124409AA 1SS244 TP ROHM KOREAD309 0DS124409AA 1SS244 TP ROHM KOREAD310 0DS124409AA 1SS244 TP ROHM KOREAD311 0DS124409AA 1SS244 TP ROHM KOREAD312 0DS124409AA 1SS244 TP ROHM KOREAD313 0DS124409AA 1SS244 TP ROHM KOREAD314 0DS124409AA 1SS244 TP ROHM KOREAD315 0DS124409AA 1SS244 TP ROHM KOREAD316 0DR140059DA 1N4005TB52 TP LITEON DO41D317 0DS141489AB 1N4148 TP GRANDE DO-34 500D401 0DS141489AB 1N4148 TP GRANDE DO-34 500D402 971-0054 TIN 50MM TAPINGD701 0DS141489AB 1N4148 TP GRANDE DO-34 500D702 0DS141489AB 1N4148 TP GRANDE DO-34 500D704 0DR150051AA DMV1500M/F5 ST SGS-THOMSOND705 0DR100009CA RGP10G TP GULF SEMICONDUCTD706 0DR359150AA BY359F-1500 BK PHILIPS SD709 0DR400409AB UF4004 TP G.I DO204AL 400VD710 0DR320400AA S3L20U-4004P15 BK SHINDENG
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
D711 0DS141489AB 1N4148 TP GRANDE DO-34 500D712 0DR100009CA RGP10G TP GULF SEMICONDUCTD714 0DS141489AB 1N4148 TP GRANDE DO-34 500D715 0DS141489AB 1N4148 TP GRANDE DO-34 500D716 0DR140059DA 1N4005TB52 TP LITEON DO41D717 0DR140059DA 1N4005TB52 TP LITEON DO41D719 0DR100009DA RGP10J TP GULF SEMICONDUCTD721 0DR100009CA RGP10G TP GULF SEMICONDUCTD723 0DS141489AB 1N4148 TP GRANDE DO-34 500D725 0DS141489AB 1N4148 TP GRANDE DO-34 500D730 971-0054 TIN 50MM TAPINGD735 0DR140059DA 1N4005TB52 TP LITEON DO41D741 0DS141489AB 1N4148 TP GRANDE DO-34 500D801 0DS141489AB 1N4148 TP GRANDE DO-34 500D802 0DS141489AB 1N4148 TP GRANDE DO-34 500D900 0DD360000DA D3SBA60 BK SHINDENGEN 600D902 971-0054 TIN 50MM TAPINGD903 0DR100009CA RGP10G TP GULF SEMICONDUCTD905 0DD400709CB UF4007 TP G.I DO204AL 100D906 0DS141489AB 1N4148 TP GRANDE DO-34 500D908 0DS141489AB 1N4148 TP GRANDE DO-34 500D941 0DD150009CB RGP15D TP G.I DO204AC 200VD942 0DRGS00089A SB1H100 GENERAL SEMICONDUCD951 0DRGS00110A UF5403L-5700 GENERAL SEMICD952 0DS141489AB 1N4148 TP GRANDE DO-34 500D961 0DRGS00090A 31GF6L-5701 GENERAL SEMICOD971 0DR100009DA RGP10J TP GULF SEMICONDUCTZD301 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD302 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD401 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD404 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD405 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD406 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD407 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD408 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD409 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD410 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD411 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD701 0DZ110009CF GDZJ11B TP GRANDE DO34 0.5ZD702 0DZ560009AG GDZJ5.6B TP GRANDE DO-34 5ZD901 0DZ510009BE GDZ5.1B TP GRANDE DO34 500ZD902 0DZ510009BE GDZ5.1B TP GRANDE DO34 500
IC301 0IPRPMJ008A MTV038N-15EG MYSON 16P DIPIC302 0IPRPNS003A LM1269NA NATIONAL SEMICONDIC303 0IPRPNS012A LM2468TA NATIONAL SEMICONDIC304 0IPRPNS005A LM2480NA NATIONAL SEMICONDIC401 0IZZTSZ170A SS 42PIN ST G-CHASSIS 4KEYIC402 0ISG240860A M24C08-BN6 8DIP BK 8K SERIIC402 0ISG240860A M24C08-BN6 8DIP BK 8K SERIIC403 0IKE704200H KIA7042AP TO-92 TP 4.2 VOIC601 0IPH486600C TDA4866J 9P ST VERTICAL OUIC701 0IPRPPH008A TDA4857PS(V2) PHILIPS SDIPIC901 0IPMGSK004A STR-G8644D(LF1140) SANKEN
FB301 6210TCE003F BRD3580B BO SUNG 3580MM RAFB302 6210TCE003J BAS2550T BO SUNG 2550MM AXFB303 6210TCE003J BAS2550T BO SUNG 2550MM AX
- 24 -
DIODEs
ICs
COILs & COREs
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
FB304 6210TCE003J BAS2550T BO SUNG 2550MM AXFB305 6210TCE003J BAS2550T BO SUNG 2550MM AXFB308 6210TCE003G BRS3550B BO SUNG 3550MM RAFB309 971-0054 TIN 50MM TAPINGFB310 6210TCE003A BRD3510B BO SUNG 3510MM RAFB311 6210TCZ001J BAS3550T0(125-022J) BO SUNFB312 6210TCZ001J BAS3550T0(125-022J) BO SUNFB313 6210TCZ001J BAS3550T0(125-022J) BO SUNFB401 6210TCE003J BAS2550T BO SUNG 2550MM AXFB402 6210TCE003J BAS2550T BO SUNG 2550MM AXFB403 6210TCE003J BAS2550T BO SUNG 2550MM AXFB701 6210TCE003L BAS3580T BO SUNG 3580MM AXFB703 6210TCE003B BRS3580B BO SUNG 3580MM RAFB705 6210TCE003L BAS3580T BO SUNG 3580MM AXFB901 6210TCE003P BRS2550B BO SUNG 2550MM RAFB904 6210TCE003K BAS3550T BO SUNG 3550MM AXFB913 6210TCE003P BRS2550B BO SUNG 2550MM RAFB921 6210TCE003A BRD3510B BO SUNG 3510MM RAFB922 6210TCE003H BAS3510T BO SUNG 3510MM AXFB951 6210TCE003J BAS2550T BO SUNG 2550MM AXL301 0LA0560K119 0.56UH K 2.3*3.4 TPL302 0LA0560K119 0.56UH K 2.3*3.4 TPL303 0LA0560K119 0.56UH K 2.3*3.4 TPL304 0LA1000K119 100UH K 2.3*3.4 TPL311 0LA0121K119 1.2UH K 2.3*3.4 TPL312 0LA0121K119 1.2UH K 2.3*3.4 TPL313 0LA0121K119 1.2UH K 2.3*3.4 TPL702 6140TBZ025C DR14*20 150UH 0.12*25MM 51L703 6140TYZ010F “LX31 GET DR14*15-C5.2,19.5”L705 6140TBZ026C DR15*18-C9.8 100UH 0.1*30ML901 6200TLS004B SQE2424 15MH 0.55MM 70T CB
Q701 0TR200009AB KTC200-Y TP KEC TO92 NPNQ706 0TR580301AA FAIRCHILD KSC5803(TBTU) STQ707 0TR127009AA KTA1270-Y(KTA562TM) TP KECQ708 0TR127009AA KTA1270-Y(KTA562TM) TP KECQ709 0TR141300AB KTD1413 BK KEC TO220I S NPQ712 0TF630000CA IRFS630A BK SAMSUNG 200V 6Q713 0TF630000CA IRFS630A BK SAMSUNG 200V 6Q715 0TR319809AA KTC3198-Y(KTC1815) TP KECQ716 0TR319809AA KTC3198-Y(KTC1815) TP KECQ719 0TF630000CA IRFS630A BK SAMSUNG 200V 6Q720 0TR390409CA 2N3904 TP SAMSUNG TO92 NPQ722 0TR319809AA KTC3198-Y(KTC1815) TP KECQ723 0TR127009AA KTA1270-Y(KTA562TM) TP KECQ799 0TR920009AB KSP92 TP SAMSUNG TO92 HIGHQ903 0TRFC10003A FAIRCHILD KSD882Y-S ST TO1Q941 0TR319809AA KTC3198-Y(KTC1815) TP KECQ942 0TR928009AB KSA928A-Y TP SAMSUNG TO92LQ951 0TR319809AA KTC3198-Y(KTC1815) TP KECQ952 0TR928009AB KSA928A-Y TP SAMSUNG TO92LQ953 0TR319809AA KTC3198-Y(KTC1815) TP KEC
R301 0RD0752Q609 75 1/4W(3 5% TA52R302 0RD0752Q609 75 1/4W(3 5% TA52R303 0RD0752Q609 75 1/4W(3 5% TA52R304 0RD3301Q609 3.30K 1/4W(3 5% TA52R305 0RD5601Q609 5.60K 1/4W(3 5% TA52
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R306 0RD5601Q609 5.60K 1/4W(3 5% TA52R307 0RD1004Q609 1M OHM 1/4 W (3.4) 5% TA52R310 0RD1000Q609 100 1/4W(3 5% TA52R312 0RD1001Q609 1K 1/4W(3 5% TA52R314 0RD1000Q609 100 1/4W(3 5% TA52R315 0RD1000Q609 100 1/4W(3 5% TA52R316 0RD1000Q609 100 1/4W(3 5% TA52R317 0RD1000Q609 100 1/4W(3 5% TA52R318 0RD1000Q609 100 1/4W(3 5% TA52R319 0RD4701Q609 4.70K 1/4W(3 5% TA52R320 0RD2001Q609 2K 1/4W(3 5% TA52R321 0RD2200Q609 220 1/4W(3 5% TA52R322 0RD2200Q609 220 1/4W(3 5% TA52R323 0RD2200Q609 220 1/4W(3 5% TA52R324 0RD2200Q609 220 1/4W(3 5% TA52R327 0RD1001Q609 1K 1/4W(3 5% TA52R328 0RD1001Q609 1K 1/4W(3 5% TA52R329 0RD1001Q609 1K 1/4W(3 5% TA52R330 0RD1000Q609 100 1/4W(3 5% TA52R331 0RD1200Q609 120 1/4W(3 5% TA52R332 0RD1100Q609 110 1/4W(3 5% TA52R333 0RD1200Q609 120 1/4W(3 5% TA52R334 0RD3303Q609 330K 1/4W(3 5% TA52R335 0RD3303Q609 330K 1/4W(3 5% TA52R336 0RD3303Q609 330K 1/4W(3 5% TA52R337 0RD1000Q609 100 1/4W(3 5% TA52R340 0RN1002F409 10K 1/6W 1 TA52R341 0RD0332A609 33 OHM 1/2 W (7.0) 5% TA52R342 0RD0332A609 33 OHM 1/2 W (7.0) 5% TA52R343 0RD0332A609 33 OHM 1/2 W (7.0) 5% TA52R344 0RD0332Q609 33 1/4W(3 5% TA52R345 0RD0332Q609 33 1/4W(3 5% TA52R346 0RD0332Q609 33 1/4W(3 5% TA52R347 0RD1200Q609 120 1/4W(3 5% TA52R348 971-0054 TIN 50MM TAPINGR388 0RD1000Q609 100 1/4W(3 5% TA52R389 0RD1000Q609 100 1/4W(3 5% TA52R390 0RD1000Q609 100 1/4W(3 5% TA52R401 0RD1000Q609 100 1/4W(3 5% TA52R402 0RD1002Q609 10K 1/4W(3 5% TA52R403 0RD2200Q609 220 1/4W(3 5% TA52R404 0RD1000Q609 100 1/4W(3 5% TA52R405 0RD1000Q609 100 1/4W(3 5% TA52R406 0RD2001Q609 2K 1/4W(3 5% TA52R407 0RD2001Q609 2K 1/4W(3 5% TA52R408 0RD3302Q609 33K 1/4W(3 5% TA52R409 0RD1300Q609 130 1/4W(3 5% TA52R410 0RD1300Q609 130 1/4W(3 5% TA52R412 0RD2001Q609 2K 1/4W(3 5% TA52R413 0RD1001Q609 1K 1/4W(3 5% TA52R414 0RD1001Q609 1K 1/4W(3 5% TA52R415 0RD1001Q609 1K 1/4W(3 5% TA52R416 0RD1801Q609 1.80K 1/4W(3 5% TA52R417 0RD1001Q609 1K 1/4W(3 5% TA52R418 0RD3901Q609 3.90K 1/4W(3 5% TA52R419 0RD1002Q609 10K 1/4W(3 5% TA52R420 0RD1002Q609 10K 1/4W(3 5% TA52R422 0RD1801Q609 1.80K 1/4W(3 5% TA52R423 0RD5600Q609 560 1/4W(3 5% TA52R430 0RD1000Q609 100 1/4W(3 5% TA52R431 0RD1000Q609 100 1/4W(3 5% TA52R432 0RD1000Q609 100 1/4W(3 5% TA52
- 25 -
TRANSISTOR
RESISTORs
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R433 0RD2001Q609 2K 1/4W(3 5% TA52R434 0RD2001Q609 2K 1/4W(3 5% TA52R441 0RD2200Q609 220 1/4W(3 5% TA52R442 0RD2200Q609 220 1/4W(3 5% TA52R443 0RD0912Q609 91 OHM 1/4 W (3.4) 5% TA52R446 0RD1002Q609 10K 1/4W(3 5% TA52R490 0RD9100Q609 910 1/4W(3 5% TA52R491 0RD2200Q609 220 1/4W(3 5% TA52R492 0RD4300Q609 430 OHM 1/4 W(3.4) 5.00% TR493 0RD7500Q609 750 OHM 1/4 W (3.4) 5% TA5R494 0RD1001Q609 1K 1/4W(3 5% TA52R495 0RD1001Q609 1K 1/4W(3 5% TA52R601 0RD1001Q609 1K 1/4W(3 5% TA52R602 0RD1001Q609 1K 1/4W(3 5% TA52R603 0RN0390H609 0.39 1/2W 5 TA52R604 0RD0111A609 1.1 OHM 1/2 W (7.0) 5% TA5R605 0RD0102A609 10 OHM 1/2 W (7.0) 5% TA52R606 0RD1000A609 100 OHM 1/2 W (7.0) 5% TA5R607 0RN5101F409 5.10K 1/6W 1% TA52R608 0RD2200A609 220 OHM 1/2 W (7.0) 5% TA5R610 0RD1101Q609 1.1K OHM 1/4 W (3.4) 5% TAR612 0RN5101F409 5.10K 1/6W 1% TA52R613 0RD1801Q609 1.80K 1/4W(3 5% TA52R700 0RX0221K607 2.2 OHM 2 W 5% TA62R701 0RD1500A609 150 OHM 1/2 W (7.0) 5% TA5R702 0RD5601Q609 5.60K 1/4W(3 5% TA52R704 0RD3601Q609 3.60K 1/4W(3 5% TA52R705 0RD1602Q609 16K 1/4W(3 5% TA52R706 0RN2701F409 2.70K 1/6W 1% TA52R707 0RN3301F409 3.30K 1/6W 1% TA52R708 0RN1001F409 1K 1/6W 1% TA52R709 0RD2202Q609 22K 1/4W(3 5% TA52R710 0RD1000Q609 100 1/4W(3 5% TA52R711 0RD1000Q609 100 1/4W(3 5% TA52R712 0RD1001Q609 1K 1/4W(3 5% TA52R713 0RD1000Q609 100 1/4W(3 5% TA52R714 0RN1501F409 1.5K 1/6W 1 TA52R714-1 0RN3001F409 3K 1/6W 1% TA52R714-2 0RN6200F409 620 1/6W 1% TA52R715 0RD2702Q509 27K OHM 1/4 W(3.4) 2% TA52R716 0RD7502Q609 75K 1/4W(3 5% TA52R717 0RD5601Q609 5.60K 1/4W(3 5% TA52R718 971-0054 TIN 50MM TAPINGR719 0RD4701Q609 4.70K 1/4W(3 5% TA52R720 0RC1205Q609 12M OHM 1/4 W(3.4) 5% TA52R721 0RD1001Q609 1K 1/4W(3 5% TA52R723 0RD1001Q609 1K 1/4W(3 5% TA52R724 0RD1001Q609 1K 1/4W(3 5% TA52R725 0RD1001Q609 1K 1/4W(3 5% TA52R726 0RD5102A609 51K OHM 1/2 W (7.0) 5% TA5R727 0RD1001Q609 1K 1/4W(3 5% TA52R728 0RX0512K665 51 OHM 2 W 5% SFR729 0RD3000A609 300 OHM 1/2 W (7.0) 5% TA5R730 0RB0150K665 0.15 OHM 2 W 5% SFR731 0RD1002Q609 10K 1/4W(3 5% TA52R732 0RD6802Q509 68K OHM 1/4 W (3.4) 2% TA5R733 0RD1002Q609 10K 1/4W(3 5% TA52R734 0RD0222A609 22 OHM 1/2 W (7.0) 5% TA52R735 0RD1001Q609 1K 1/4W(3 5% TA52R736 0RX1501J609 1.5KOHM 1 W 5% TA52R737 0RN0560H609 0.56 1/2W 5 TA52R738 0RN0560H609 0.56 1/2W 5 TA52
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R740 0RD0271A609 2.7 OHM 1/2 W (7.0) 5% TA5R744 0RD2700A609 270 OHM 1/2 W (7.0) 5% TA5R745 0RD4702Q609 47K 1/4W(3 5% TA52R747 0RD3001Q609 3K 1/4W(3 5% TA52R748 0RD4702Q609 47K 1/4W(3 5% TA52R749 0RD2201Q609 2.20K 1/4W(3 5% TA52R750 0RD3001Q609 3K 1/4W(3 5% TA52R752 0RD2201Q609 2.20K 1/4W(3 5% TA52R754 0RX4300K607 430 OHM 2 W 5% TA62R755 0RD0471Q609 4.70 1/4W(3 5% TA52R756 0RD2202A609 22K OHM 1/2 W (7.0) 5% TA5R757 0RD0222A609 22 OHM 1/2 W (7.0) 5% TA52R758 0RN1303F409 130K 1/6W 1% TA52R759 0RD1302Q509 13K OHM 1/4 W (3.4) 2% TA5R760 0RD5103Q609 510K 1/4W(3 5% TA52R761 0RD3001Q609 3K 1/4W(3 5% TA52R762 0RD3001Q609 3K 1/4W(3 5% TA52R764 0RD6201Q609 6.20K 1/4W(3 5% TA52R766 0RD6200Q609 620 1/4W(3 5% TA52R771 0RD3301Q609 3.30K 1/4W(3 5% TA52R772 0RD2702Q509 27K OHM 1/4 W(3.4) 2% TA52R773 0RD3302A609 33K OHM 1/2 W (7.0) 5% TA5R775 0RD4701Q609 4.70K 1/4W(3 5% TA52R789 0RD6800Q609 680 1/4W(3 5% TA52R797 0RD1501Q609 1.50K 1/4W(3 5% TA52R798 0RD2001Q609 2K 1/4W(3 5% TA52R799 0RD1502Q609 15K 1/4W(3 5% TA52R801 0RD2402Q609 24K 1/4W(3 5% TA52R802 0RD3302Q609 33K 1/4W(3 5% TA52R803 0RD2001Q609 2K 1/4W(3 5% TA52R805 0RD2001Q609 2K 1/4W(3 5% TA52R806 0RD4702Q609 47K 1/4W(3 5% TA52R808 0RD9102Q609 91K OHM 1/4 W (3.4) 5% TA5R809 0RMZTWD001G RWR SMART 1OHM 5 W 5% PD TR813 0RD4302A609 43K OHM 1/2 W(7.0) 5.00% TR814 0RD1002Q609 10K 1/4W(3 5% TA52R816 0RN5601F409 5.60K 1/6W 1% TA52R818 0RN2702F409 27K 1/6W 1% TA52R819 0RD4702Q609 47K 1/4W(3 5% TA52R831 0RD1002Q609 10K 1/4W(3 5% TA52R901 0RD4703A609 470K OHM 1/2 W (7.0) 5% TAR903 0RD5600A609 560 OHM 1/2 W (7.0) 5% TA5R904 0RX1503K607 150K OHM 2 W 5% TA62R905 0RD2201Q609 2.20K 1/4W(3 5% TA52R906 0RD6200Q609 620 1/4W(3 5% TA52R908 0RN0220H609 0.22 1/2W 5% TA52R910 0RX4702J609 47K OHM 1 W 5% TA52R925 0RB0120K607 0.12 OHM 2 W 5% TA62R941 0RN0220H609 0.22 1/2W 5% TA52R944 0RD4700A609 470 OHM 1/2 W (7.0) 5% TA5R945 0RD4701Q609 4.70K 1/4W(3 5% TA52R951 971-0054 TIN 50MM TAPINGR952 0RD4702A609 47K OHM 1/2 W (7.0) 5% TA5R953 0RX4700J609 470 OHM 1 W 5% TA52R954 0RD4701Q609 4.70K 1/4W(3 5% TA52R955 0RD4701Q609 4.70K 1/4W(3 5% TA52R956 0RD4702Q609 47K 1/4W(3 5% TA52R957 0RD0472A609 47 OHM 1/2 W (7.0) 5% TA52R960 0RD2200A609 220 OHM 1/2 W (7.0) 5% TA5R967 971-0054 TIN 50MM TAPING
- 26 -
DATE: 2002. 02. 05. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
F1 430-858C AFC-520 BAE EUN TAF2 430-858C AFC-520 BAE EUN TAF901 0FZZTTH001D “TIME LAG HBC 3.15A/250V,21”J59 0RD1000Q609 100 1/4W(3 5% TA52J99 0RD6802Q609 68K 1/4W(3 5% TA52RL901 6920TBA001A DY3MA-DC12 DONGYANG 250VACSC301 6620TBC002A PCS629-01B PARK ELEC. 8PINSC901 6620TKB002B SA-4S HUA JIE AC UNIVERSALSG301 6918TRT005A “SSG-102-A0,1KV SMART RADIA”SG302 6918TRT005A “SSG-102-A0,1KV SMART RADIA”SG303 6918TRT005A “SSG-102-A0,1KV SMART RADIA”SG304 6918TRT005A “SSG-102-A0,1KV SMART RADIA”SG305 6918TRT005A “SSG-102-A0,1KV SMART RADIA”SW1 6600R00001B JTP1286 JEIL 12V DC 1MA VESW2 6600R00001B JTP1286 JEIL 12V DC 1MA VESW3 6600R00001B JTP1286 JEIL 12V DC 1MA VESW4 6600R00001B JTP1286 JEIL 12V DC 1MA VESW5 6600R00001B JTP1286 JEIL 12V DC 1MA VET1 5240T0B002A W-T 480MM UL1007 AWG 24 TWT2 5240T0B002A W-T 480MM UL1007 AWG 24 TWT701 6174Z-1035G FMMTC81 AM1035G (LIM SANGT703 6170TCZ001D “EI2218 4.0MH H-DRIVE,EB770”T901 6170TMZ132A EER3541 150UH V-16PIN EB77TH901 6322B00002B MZ72-9RM290V GAOLI 9OHM 20TH902 6322TA080BA SCK-084 THINKING 8 ohm 15%X401 6202TTB003B HC-49/U HARMONY RADIAL 12M
- 27 -
OTHERs
PIN CONFIGURATION
- 28 -
TDA4866J Current Driven Vertical Deflection Booster
SYMBOL
INA
INB
VP
OUTB
GND
OUTA
VFB
GUARD
FEEDB
PIN
1
2
3
4
5
6
7
8
9
TDA4866J
1INA
2INB
5GND
6OUTA
8GUARD
9FEEDB
7VFB
4OUTB
3Vp
TDA4866J
Pin Configuration1
9
Vin4
1
2
5
3
START O.V.P LATCH DRIVE
Vth1
Vth2
O.S.C
ERROR AMP
GND
O.C.P/F.B
S
D
+
+
+
REG.
STR-G8644D
Block Diagram
M24C08 Serial I2C BUS EEPROM
SYMBOL
E0-E2
SDA
SCL
WC
Vcc
Vss
DESCRIPTION
Chip Enable Input
Serial Data Address Input/Output
Serial Clock
Write Control
Supply Voltage
Ground
1
PSDIP8 (BN)0.25mm Frame
8
1
1
SO8 (MN)150mil Width
TSSOP8 (DW)169mil Width
8
8
Logic Dirgram
- 29 -
TDA4857
TDA4857 Autosync Deflection Controller
TDA4857
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
23
22
25
24
21
20
19
18
17
32
31
30
29
28
27
26
VREF
VAGC
SGND
VCAP
VSMOD
i.c
SDA
SCL
HUNLOCK
FOCUS
HSMOD
HPLL2
HCAP
HREF
HBUF
HPLL1
EWDRV
VOUT2
XSEL
VCC
VOUT1
VSYNC
HSYNC
CLBL
PGND
HFLB
XRAY
BOP
BSENS
BIN
BDRV
HDRV
SYMBOL
HFLB
XRAY
BOP
BSENS
BIN
BDRV
PGND
HDRV
XSEL
Vcc
EWDRV
VOUT2
VOUT1
VSYNC
HSYNC
CLBL
DESCRIPTION
Horizontal Flyback Input
X-ray Protection Input
B+ Control OTA Output
B+ Control Comparator Input
B+ Control OTA Input
B+ Control Driver Output
Power Ground
Horizontal Driver Output
Select Input for X-ray reset
Supply Voltage
EW Waveform Output
Vertical Output 2 (Ascending Sawtooth)
Vertical Output 1 (Descending Sawtooth)
Vertical Synchronization Input
Horizontal / Composite Synchronization Input
Video Clamping Pulse / V-Blanking Output
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SYMBOL
HUNLOCK
SCL
SDA
i.c
VSMOD
VAGC
VREF
VCAP
SGND
HPLL1
HBUF
HREF
HCAP
HPLL 2
HSMOD
FOCUS
DESCRIPTION
H-Synchronization Unlock/Protection/V-Blanking Output
I2C-Bus Clock Input
I2C-Bus Data Input
Internally connected; nite 1
Input for EHT Compensation (Via V-Size)
External Capacitor for V-Amplitude Control
External Resistor for Vertical Oscillator
External Capacitor for Vertical Oscillator
Signal Ground
External Filter for PLL1
Buffered F/V Voltage Output
Reference Current for Horizontal Oscillator
External Capacitor for Horizontal Oscillator
External Filter for PLL2 / Soft Start
Input for EHT Compensation (Via H-Size)
Output for Vertical Focus
PIN
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Pin Configuration
1
32
IIC-SDAIIC-SCLDDC-SDADDC-SCL
- 30 - - 31 -
SCHEMATIC DIAGRAM
NOTICESince this is a basic schematic diagram.The value of components and some partial connection are
- 32 - - 33 -
PRINTED CIRCUIT BOARD
1. MAIN BOARD (Component Side) 2. MAIN BOARD (Solder Side)
Feb. 2002P/NO : 3828TSL081A Printed in Korea