COLD CUT SAW1280W INSTRUCTION MANUALSPECIFICATIONSRated Voltage: 230 – 240V ~ 50Hz

Rated Power: 1280W

No Load Speed: 3800rpm

Supplied Blade: Ø180mm (7”) x Ø20mm x 1.9 (36T)

Cutting Blade Max.: Ø185mm (7-1/4”)

Cutting Angle Capacity: 0 – 45°Max Cutting Capacity

Round & Square Tube: 50mm - 6 mm Section

Rectangular Profile: 75mm x 45mm - 6mm Section

Round & Square Bar: 20mm Mild Steel

Net Weight: 7.7kg

CCS-1200

WHAT’S IN THE BOX

ozito.com.au

5mm & 6mm Hex key

Cold Cut Saw

Carbon Brush Set

3

ONLINE MANUALScan this QR Code with your mobile device to take you to the online manual.

1 Carry handle

2 Upper blade guard

3 Lock off button

4 Blade bolt cover

5 Retractable blade guard

6 Depth stop

7 Blade

8 Fence

9 Angle guide lock lever

10 Angle guide

11 Rear spark shield

12 Vice handle

13 Rubber foot

14 Vice lock

15 Base

16 Spindle lock lever

17 Lock pin

18 Trigger switch

19 Vice

COLD CUT SAW

KNOW YOUR PRODUCT

1. ADJUSTMENTS

SETUP & PREPARATION

Locking & releasing the lock pinThe cold cut saw is boxed in a locked position. To unlock the saw and raise the saw arm, depress the saw arm slightly and pull the lock pin out. The saw arm will pivot upwards.To lock the saw so that it can be carried or transported, fold the saw arm down and push in the lock pin.

Adjusting the vise1. Place your workpiece on the

cold cut saw base, between the fence and vice.

2. Disengage the vice lock and push the vice handle forward. The vice can easily be moved forwards and backwards if the vice lock is disengaged.

3. When the vice is touching the workpiece, close the vice lock.

4. Turn the vice handle in a clockwise direction to clamp the workpiece securely in position.

5. To remove an object from the vice, rotate the vice handle in an anti-clockwise direction. When the clamping pressure is relieved, the vice lock can be disengaged and the vice handle can be pulled back.

.

19

17

16

18

11

15

1098

1

2

3

4

5

6

7

12 13 14 3

Adjusting the depth stopEnsure that the depth stop is adjusted to the correct height before commencing operation. The adjustable depth stop is threaded into the pivot mount at the rear of the base. By raising and lowering the depth stop, the distance that the blade travels can be controlled.

1. Toadjustthedepthstop,firstloosenthe depth stop nut (anti clockwise).

2. If you wish to increase the depth of cut, use the 6mm hex key (supplied) to rotate the depth stop clockwise. This will lower the height of the depth stop.

3. If you desire a shallower depth of cut, use the 6mm hex key (supplied) to rotate the depth stop anti clockwise. This will increase the height of the depth stop and restrict the distance that the saw arm can travel.

4. Whenyouaresatisfiedwiththedepthstop height, hold the depth stop steady with the 6mm hex key and tighten the depth stop nut.

Adjusting the cutting angleNote. The angle guide allows cutting angles from 0° to 45°.

1. Toadjustthecuttingangle,firstloosen the angle guide lock lever by turning it in an anti-clockwise direction.

2. Move the angle guide until the slot line in the base aligns with the desired cutting angle.

3. Tighten the angle guide lock lever by turning it in a clockwise direction.

Note. The angle guide is just a guide. More accurate square cuts can be achieved by lowering the arm down until the blade sits within the base. Sit a square edge against the blade and adjust the fence against the square edge. Tighten the angle guide lock lever before use.

IMPORTANT! BEFORE ADJUSTING THE CUTTING ANGLE WITH A SQUARE EDGE, ENSURE THAT THE UNIT HAS BEEN SWITCHED OFF AND THE PLUG REMOVED FROM THE SOCKET. WARNING! NEVER OPERATE THE COLD CUT SAW

WITHOUT THE JAM NUT AND THE DEPTH STOP FULLY SECURE.

3. TURNING ON AND OFF2. MAXIMUM CUTTING CAPACITIES

1. Depress and hold the lock-off button then pull the trigger switch to start the tool. After starting release the lock-off button.

2. To stop the tool release the trigger switch.

3. When the trigger switch is released the machine turns off. The lock-off button will automatically re-engage.

OPERATION

6mm50mm

50mm

75mm

45mm

6mm

50mm 50mm

6mm

20mm

20mm

20mm

50mm

6mm50mm

50mm

75mm

45mm

6mm

50mm 50mm

6mm

20mm

20mm

20mm

50mm

6mm50mm

50mm

75mm

45mm

6mm

50mm 50mm

6mm

20mm

20mm

20mm

50mm

6mm50mm

50mm

75mm

45mm

6mm

50mm 50mm

6mm

20mm

20mm

20mm

50mm

The cut off saw is recommended for cutting mild steel such as pipe, box section, rectangular, angle iron and mild steel bars.The diagrams below indicate maximum cutting capacities and assume no blade wear and ideal fence positioning. These capacities are suited to 90° & 45°

Tubes & Angles

Solid BarRecommended for mild steel and copper alloys.

6mm50mm

50mm

75mm

45mm

6mm

50mm 50mm

6mm

20mm

20mm

20mm

50mm

6mm50mm

50mm

75mm

45mm

6mm

50mm 50mm

6mm

20mm

20mm

20mm

50mm

4. OPERATION 5. REPLACING A BLADE

MAINTENANCE

When all the necessary adjustments have been made including adjusting the vice, cutting angle and depth stop (see Adjustments section), the operation of the cold cut saw can commence.

1. Ensure that the workpiece is fully clamped into place before beginning to cut.

2. Depress the lock-off button and pull the trigger to start the tool.

3. Lower the blade onto the workpiece and allow it to cut its way through. (Let let blade do the cutting).

4. After the completion of the cut, raise the blade clear of the workpiece. Release the trigger and the cold cut saw will stop.

1. With the 5mm hex key (supplied), loosen the 2 hex bolts that attach the blade bolt cover to the upper blade guard. Slide the cover up to remove.

2. Remove the blade bolt cover so that the blade bolt is exposed.

3. Lower and hold the spindle lock lever and rotate the blade anti-clock wise until the spindle lock engages.

4. With one hand, keep the spindle lock lever lowered. Use the other hand to unscrew the blade bolt with the 6mm hex key (supplied) in an anti-clockwise direction.

5. Removethebladebolt,flangewasherandtheouterflange.

IMPORTANT! BEFORE CLEANING YOUR COLD CUT SAW OR CARRYING OUT ANY MAINTENANCE PROCEDURE, MAKE SURE THAT THE MOTOR IS OFF AND THE TOOL DISCONNECTED FROM THE POWER SUPPLY TO PREVENT ACCIDENTAL STARTING.

WARNING! NEVER OPERATE THE COLD CUT SAW WITHOUT WEARING THE APPROPRIATE SAFETY GEAR INCLUDING EYE AND HEARING PROTECTION.

CAUTION! THE BLADE MAY CONTINUE SPINNING FOR A SHORT WHILE AFTER THE TRIGGER HAS BEEN RELEASED. KEEP YOUR HANDS AWAY FROM A MOVING BLADE.

MAINTENANCE

5. REPLACING A BLADE cont. 6. CLEANING

6. Slide the retractable blade guard into the upper blade guard. Removethebladeandtheinsideflange.

7. Clean any dust and debris from the spindle, theinnerflangeandthe other components. Re-assemble the blade components in the reverse order, ie. Inner flange,replacementblade,outerflange,flangewasherandthenthe blade bolt.

Note. When mounting the blade, make sure that the direction of rotation arrow printed on the blade matches the direction of rotation arrow embossed on the upper blade guard.

8. Lower and hold the spindle lock lever and tighten the blade bolt in a clockwise direction.

9. Rotate the new disc by hand, ensuring that it doesn’t wobble and rotates fully.

10. Replace the front blade bolt coverandfixitinplacewith the 2 hex bolts.

CleaningRemove dust and dirt regularly from the machine. Cleaning is best carriedoutwithafinebrushoracloth.Remove any metal and debris that may have accumulated around the upper blade guard and retractable blade guard.Clean debris from saw recess in bass.Clean chips from spark shield.Never use caustic agents to clean plastic parts.Keep the tool’s air vents unclogged and free of dust and dirt. Blow out the motor regularly with compressed air.

General inspectionBefore use, check for cracked or broken parts, damaged electrical wiring and any other condition that may effect safe operation. Do not use damaged equipment.

Regularlycheckthatallthefixingscrewsaretight.Theymayvibrateloose over time.

Carbon brushesWhen the carbon brush wears out, the cold cut saw will spark and/or stop. Discontinue use as soon as this happens. It should be replaced prior to recommencing use of the cold cut saw. Carbon brushes are a wearing component of the saw therefore not covered under warranty. Continuing to use the cold cut saw when carbon brushes need to be replaced may cause permanent damage to the saw. Carbon brushes will wear out after many uses. When the carbon brush needs to be replaced, take the saw to an electrician or a power tool repairer for a quick and low cost replacement. Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the saw by an unauthorised person or by mishandling of the saw.

DESCRIPTION OF SYMBOLS CARING FOR THE ENVIRONMENTPower tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. Please recycle where facilities exist. Check with your local council authority for recycling advice.

Recyclingpackagingreducestheneedforlandfillandrawmaterials.Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice.

SPARE PARTS

V Volts Hz Hertz

~ Alternating current W Watts

/min Revolutions or reciprocation per minute Double insulated

Regulator compliance mark no No load speed

Read instruction manual

Blade ø180mm x ø20mm x 36TCT SPCCS1200-62Blade Bolt & Washer SPCCS1200-59KCarbon Brush (Pair) SPCCS1200-05Carbon Brush Holder (Pair) SPCCS1200-04Guard Spring SPCCS1200-67Guard SPCCS1200-65

Spare parts can be ordered from the Special Orders Desk at your local Bunnings Warehouse.

For further information, or any parts not listed here, visit www.ozito.com.au or contact Ozito customer service Australia 1800 069 486 New Zealand 0508 069 486 E-mail: enquires@ozito.com.au

SPARE PARTS Tool: Model No.

Item No. Description Part No.

How To Order

040559626567

Carbon Brush Holder (Pair)Carbon Brush (Pair) Blade Bolt & Washerlade ø180mm x ø20mm x 36TCTGuardGuard Spring

SPCCS1200-04SPCCS1200-05SPCCS1200-59KSPCCS1200-62SPCCS1200-65SPCCS1200-67

Available spare parts can be ordered through the Special Orders Desk at any Bunnings Warehouse. If you have any further questions, please contact Ozito Customer Service on:Australia: 1800 069 486New Zealand: 0508 069 486enquiries@ozito.com.au

The following is a list of spare parts carried by Ozito. Please contact Customer Service for any parts not listed.

Tool: Cold Cut Saw

Model No. CCS-1200

12

3

4

56

10

1112

1314

15

916

17918

1920 21

22

23

242514189

14

54

5758

59

60

61

62

6364

6566

6771

7288

7374

7576 41

40

7069

8945

53

51

52 28

2930

26

916

2750

4948

4712

3939 4342

404176

4176

4640

417644

7677

417876

68

5556

7

313233343536

80

9 37387940

2981828384

85867687

89

Item No. Description Part No.

WARNINGS!.Always wear eye protection.- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.- Young children should be supervised to ensure that they do not play with the appliance.a) Check the blade before mounting it into the saw. Make sure that it is in no way cracked or

warped. Only use sharp blades.b) When the blade is installed, stand to one side, out of line with the blade, and run the tool

for at least a minute to make sure that it is not faulty. Always stay out of line of the blade when using the saw.

c) Do not use a blade marked with a lower RPM than that of the no load speed shown on the rating plate of the tool.

d) Check that the mains voltage matches that given on the rating plate before plugging in the tool.

e) Ensure that the workpiece is held tight in the vise.f) When cutting through long material, ensure that it is supported properly by packing up

each end to match the height of the vise.g) Use only good quality blades.h) Let the blade do the cutting at a reasonable feed. If too much pressure is applied the motor will

beoverloadedcausingthebladetoslowresultingininefficientcuttingandpossibledamagetothemotor.

i) When operating the cold cut saw, use safety equipment including safety goggles or shield, ear protection, dust mask and protective clothing including safety gloves.

j) Do not use the saw unless the guards are in place.k) Always stand to one side when operating the saw. l) Never use your hands to remove debris or waste close by the saw blade.m) Rags, cloths, cord, string and the like should never be left around the work area.n) Donotattempttofreeajammedbladebeforefirstswitchingoffthemachine.o) Do not slow or stop a blade with a piece of metal. Let the blade come to rest naturally.

p) If you are interrupted when operating the saw, complete the process and switch off before looking up.

q) Periodicallycheckthatallnuts,boltsandotherfixingsareproperlytightened.r) Always hold the saw on parts that are insulated. If you accidentally cut into hidden wiring or

the saw’s own cable, the metal parts of the saw will become ‘live’. Switch off at the mains and remove the plug immediately.

s) Wear gloves when handling saw blades.t) Keepthefloorareaaroundthemachinelevel, well maintained and free of loose materials such

as cut-offs.WARNING! For your own safety read instruction manual before operating cold cut saw. Wear eye protection. Keep hands out of path of saw blade. Do not operate saw without guards in place. Do not perform any operation freehand. Never reach around saw blade. Turn off

tool and wait for saw blade to stop before moving workpiece or changing settings. When changing the blade, replace and secure all guarding to its original position and correctly before starting tool. Disconnect power (or unplug tool as applicable) before changing blade or servicing. Do not expose to rain or use in damp locations.

WARNING. Before connecting a tool to a power source (mains switch power point receptacle, outlet,etc.)besurethatthevoltagesupplyisthesameasthatspecifiedonthenameplateofthetool.Apowersourcewithavoltagegreaterthanthatspecifiedforthetoolcanresultin

serious injury to the user, as well as damage to the tool. If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate rating is harmful to the motor.The tool must be used only for its prescribed purpose. Any use other than those mentioned in this Manual will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes.Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design:• Contact with the blade.• Kickback of workpiece and parts of workpiece.• Blade fracture.• Damage to hearing if effective earmuffs are not worn.• Harmful emissions of dust when the machine is used in closed rooms. Do not use blades that are deformed or cracked. Always remove the plug from the mains socket before making any adjustments or maintenance, including changing the blade.

COLD CUT SAW SAFETY WARNINGS

WARNING! When using mains-powered tools, basic safety precautions, including thefollowing,shouldalwaysbefollowedtoreduceriskoffire,electricshock,personal injury and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool. Save these instructions and other documents supplied with this tool for future reference.The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate.Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.

This tool is double insulated in accordance with AS/NZS 60335-1; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool.Using an Extension LeadAlways use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input of the tool or which is damaged or defective may result in a risk offireandelectricshock.

WARNING! Read all safety warnings and all instructions. Failure to follow the warningsandinstructionsmayresultinelectricshock,fireand/orseriousinjury. Save all warnings and instructions for future reference. The term “power tool” in the

warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.1. Work area safety a. Keep work area clean and well lit. Cluttered or dark areas invite accidents. b. Donotoperatepowertoolsinexplosiveatmospheres,suchasinthepresenceofflammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c. Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.2. Electrical safety a. Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.Unmodifiedplugsandmatching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety a. Stay alert, watch what you are doing and use common sense when operating a power

tool.Donotuseapowertoolwhileyouaretiredorundertheinfluenceofdrugs,alcoholor medication. A moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power

toolswithyourfingerontheswitchorenergisingpowertoolsthathavetheswitchoninvitesaccidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care a. Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5. Service a. Haveyourpowertoolservicedbyaqualifiedrepairpersonusingonlyidentical

replacement parts. This will ensure that the safety of the power tool is maintained. b. If the supply cord is damaged, it must be replaced by the manufacturer,

itsserviceagentorsimilarlyqualifiedpersonsinordertoavoidahazard.

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE:

Australia 1800 069 486New Zealand 0508 069 486

3 YEAR REPLACEMENT WARRANTYYour product is guaranteed for a period of 36 months from the original date of purchase. If a product is defective it will be replaced in accordance with the terms of this warranty. Warranty excludes consumable parts, for example: blade, hex key, bearings & carbon brushes.

WARNINGThe following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other than that specified on the tool.

• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the instruction manual.

• If the tool is disassembled or tampered with in any way.• Professional, industrial or high frequency use.

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.

OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under this warranty, however, where you have suffered any additional direct loss as a result of a defective product you may be able to claim such expenses by contacting our customer service helpline above.

1013