9

STEP 1 Attach bracket to the wall.

Find stud and select position for bracket (1) on the wall.

Level bracket and mark holes with a pencil then drill

pilot holes.

Using a socket wrench fix arm bracket to the wall

with hex head screws (5) and washers (9). If fixing to brick or

concrete use plastic anchors (7).

Cover screw with plastic cap (6).

STEP 3 Attach railings to back of the TV.

Locate screw fixtures in the back of your TV

and attach railings (3) using the screws

provided.

The screw size required will vary on each TV so we have provided you

with a range to choose from (M5, M6, M8).

Optional:Insert spacers (8) or

additional washers (9) if back of TV is not a flat.

Attach face plate (2) to arm bracket using the allen key (13), bolt (4)

and black washers (10). Securely tighten nut (4)

using the wrench provided (12).

Clip cable saddle (11) onto base of arm.

STEP 2 Attach face plate to bracket.

STEP 4 Hook TV onto face plate STEP 5 Adjusting tilt and roll.

Once the railings (3) are firmly attached to the TV, hook the railings onto the face plate (2) and secure into place using locking screws provided.

Note: Make sure all screws are firmly tightened after adjusting tilt and roll.

You can easily adjust the tilt and roll of the TV by simply loosening the bolts in the centre of the face plate with the allen key provided (14).

Secure bolts tightly for a fixed position or leave slightly loosened for an adjustable platform.

ADJUST TILT HERE

ADJUST ROLL HERE

Mar 2012

1

2

2

3

3

3

4

4

10

10

13

12

11

10

10

1

5

5

9

6

6

(M5, M6, M8)

(M5, M6, M8)

w w w . t a u r i s . c o m . a uDISTRIBUTED BY RVM AUSTRALIA t: (08) 9417 9944 e: sales@rvm.com.au

IMPORTANT: PRE-DRILL HOLESMake sure bracket is secured to stud,or anchors are used for brick or concrete.

CMW - 297Professional Installer Highly Recommended - The bracket manufacturer will not warrant any faulty installations, and damage to panels or any other fixtures / fittings as a result of incorrect installation.

CMW - 297

No. Part Qty1 Wall Bracket With Arm 12 Face Plate 13 Railings 24 Pivot Bolt & Nut 15 Hex Screw 26 Plastic Cap 27 Masonry Anchors 2

No. Part Qty8 Plastic Spacer L12.5 49 Washer Silver ø8 ø18 1010 Washer Black ø6 ø18 411 Cable Saddle 212 Wrench 113 Allen No. 6 114 Allen No. 5 1

4. 12.5. 7. 11.

13. 14.

9.

10.

8.6.

M8M5

PARTS DRAWN TO SCALE 1:1

NOTE: Use spring washers when securing bolts. This will reduce the risk of bolts coming loose.

Spring Washer

Spring Washer

Spring Washer

x4 x4 x4

M6

A drill will be required to drill pilot holes for the arm bracket.

Masonry Wall - 9mm bit

Studded Wall - 5mm bit

A socket wrench will be required whereveryou see this icon.

Hex Socket - 13mm or 1/2”��

ADDITIONAL TOOLS REQUIRED

PARTS LIST

Mar 2012

w w w . t a u r i s . c o m . a uDISTRIBUTED BY RVM AUSTRALIA t: (08) 9417 9944 e: sales@rvm.com.au