Embed Size (px)
Citation preview
Swiss innovation in CMOS image sensors and CMOS cameras
CMOS Image Sensors
Board Level CamerasOEM Camera ModulesCMOS Cameras
Index
CMOS Image Sensors 4
A1312 Series 4A1312I Series 6A1312IE Series 8A1312C Series 10A2080 Series 12
OEM Camera Modules 14
Board Level Cameras 15
Camera Selection Chart 16
CMOS Area Scan Cameras 18
MV-D640 Series 18MV-D752E Series 20DS1-D1024 Series 22MV-D1024E Series 24MV2-D1280-640 26DS1-D1312 Series 28MV1-D1312 Series 30MV1-D1312C-160 32MV1-D1312I Series 34MV1-D1312IE Series 36MV1-D2080 Series 38
Cameras with Image Preprocessing 40
MV1-D1024E-PP01-40 40
Smart Cameras 42
SM2-D1024-80 42SM2-D1312 Series 44
3D Cameras 46
MV-D1024E-3D01-160 46
Electroluminescence Cameras 48
EL1-D1312-160 48
Accessories 50
CameraLink® Repeater 50
CMOS Image Sensor
Features – 1312 x 1082 pixel resolution – 8 µm x 8 µm square pixel – Monochrome – Global shutter – Over 60% fill factor without microlenses – Good NIR response – Dynamic range up to 120 dB via LinLog®
– Up to 110 fps @ full resolution – Sequential, simultaneous or nondestructive
read out – Horizontal and vertical windowing – Flexible ROI and Multiple ROI – Integrated test pattern, temp. sensor and black
level reference
A1312 SeRIeS1.4 Megapixel monochrome CMOS image sensor
Spectral response of the Photonfocus A1312 CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
4
CMOS Image Sensors
A1312 Series
A1312-40 A1312-160
Image Sensor
Technology CMOS active pixel (APS)Scanning system • Progressive scan • Arbitrary row adressing • Region of Interest (ROI) X and Y
• Multiple Region of Interest (MROI) X and Y • Multiple nondestructive readouts possibleOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixels (active pixels)Pixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Output swing 1.05 V (typical application)Random noise (RMS) 1.1 mVFPN (RMS, uncorrected) 13.5 mVDark current 0.65 fA/pixel @ 27°C (1)
Full well capacity 140 ke¯ (2)
Spectral range < 370 to 1000 nm (to 10 % of peak responsivity) Responsivity 819 V/J/m² (3)
Quantum Efficiency > 50 % (3)
Sensitivity (for 10dB SNR) 4.0 µJ/m² (3)
Shutter efficiency 99.85 % (4)
Optical fill factor > 60 % (3)
Dynamic range 60 dB in linear mode; 120 dB with LinLog® Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential or simultaneous read out (read out during exposure)Analog taps 1 4 (1 or 4 taps active)Pixel clock 40 MHz (5)
Maximum frame rate 27 fps @ max. resolution37 fps @ 1024 x 1024 resolution
110 fps @ max. resolution150 fps @ 1024 x 1024 resolution
Supply voltages 3.1 V, 3.3 V, 4.6 VPower consumption < 480 mW during full-speed read out < 600 mW during full-speed read outOperating temperature range Industrial (-20°C ... +85°C)Package 144-pin CQFPCover glass No cover glass
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.4
(1) Varies strongly with temperature(2) When configured for 1.1 V output swing(3) Under red illumination (625 nm)(4) Under white LED illumination(5) 60 MHz possible with slightly reduced image quality
5
CMOS Image Sensor
Features – 1312 x 1082 pixel resolution – 8 µm x 8 µm square pixel – Monochrome – Global shutter – Over 60% fill factor without microlenses – Excellent NIR response – Dynamic range up to 120 dB via LinLog®
– Up to 110 fps @ full resolution – Sequential, simultaneous or nondestructive
read out – Horizontal and vertical windowing – Flexible ROI and Multiple ROI – Integrated test pattern, temp. sensor and black
level reference
A1312I SeRIeSnear Infrared (nIR) 1.4 Megapixel monochrome CMOS image sensor
Spectral response of the Photonfocus A1312I CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
6
A1312I Series
A1312I-40 A1312I-160
Image Sensor
Technology CMOS active pixel (APS)Scanning system • Progressive scan • Arbitrary row adressing • Region of Interest (ROI) X and Y
• Multiple Region of Interest (MROI) X and Y • Multiple nondestructive readouts possibleOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixels (active pixels)Pixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Output swing 1.05 V (typical application)Random noise (RMS) 1.1 mVFPN (RMS, uncorrected) 13.5 mVDark current 0.65 fA/pixel @ 27°C (1)
Full well capacity 140 ke¯ (2)
Spectral range < 370 to 1100 nm (to 10 % of peak responsivity) Responsivity 1200 V/J/m² (3)
Quantum Efficiency > 50 % (3)
Sensitivity (for 10dB SNR) 3.0 µJ/m² (3)
Shutter efficiency 99.85 % (4)
Optical fill factor > 60 % (3)
Dynamic range 60 dB in linear mode; 120 dB with LinLog® (3) Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential or simultaneous read out (read out during exposure)Analog taps 1 4 (1 or 4 taps active)Pixel clock 40 MHz (5)
Maximum frame rate 27 fps @ max. resolution37 fps @ 1024 x 1024 resolution
110 fps @ max. resolution150 fps @ 1024 x 1024 resolution
Supply voltages 3.1 V, 3.3 V, 4.6 VPower consumption < 480 mW during full-speed read out < 600 mW during full-speed read outOperating temperature range Industrial (-20°C ... +85°C)Package 144-pin CQFPCover glass No cover glass
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.4
(1) Varies strongly with temperature(2) When configured for 1.1 V output swing(3) Under red illumination (625 nm)(4) Under white LED illumination(5) 60 MHz possible with slightly reduced image quality
7
CMOS Image Sensor
Features – 1312 x 1082 pixel resolution – 8 µm x 8 µm square pixel – Monochrome – Global shutter – Over 60% fill factor without microlenses – Very good NIR response – Dynamic range up to 120 dB via LinLog®
– Up to 110 fps @ full resolution – Sequential, simultaneous or nondestructive
read out – Horizontal and vertical windowing – Flexible ROI and Multiple ROI – Integrated test pattern, temp. sensor and
black level reference
A1312Ie SeRIeS1.4 Megapixel monochrome CMOS image sensor
Spectral response of the Photonfocus A1312Ie CMOS image sensor
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
8
A1312IE Series
A1312IE-40 A1312IE-160
Image Sensor
Technology CMOS active pixel (APS)Scanning system • Progressive scan • Arbitrary row adressing • Region of Interest (ROI) X and Y
• Multiple Region of Interest (MROI) X and Y • Multiple nondestructive readouts possibleOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixels (active pixels)Pixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Output swing 1.05 V (typical application)Random noise (RMS) 1.1 mVFPN (RMS, uncorrected) 13.5 mVDark current 0.65 fA/pixel @ 27°C (1)
Full well capacity 140 ke¯ (2)
Spectral range < 370 to 1050 nm (to 10 % of peak responsivity) Responsivity 819 V/J/m² (3)
Quantum Efficiency > 45 % (3)
Sensitivity (for 10dB SNR) 4.0 µJ/m² (3)
Shutter efficiency 99.85 % (4)
Optical fill factor > 60 % (3)
Dynamic range 60 dB in linear mode; 120 dB with LinLog® Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential or simultaneous read out (read out during exposure)Analog taps 1 4 (1 or 4 taps active)Pixel clock 40 MHz (5)
Maximum frame rate 27 fps @ max. resolution37 fps @ 1024 x 1024 resolution
110 fps @ max. resolution150 fps @ 1024 x 1024 resolution
Supply voltages 3.1 V, 3.3 V, 4.6 VPower consumption < 480 mW during full-speed read out < 600 mW during full-speed read outOperating temperature range Industrial (-20°C ... +85°C)Package 144-pin CQFPCover glass No cover glass
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.0.0
(1) Varies strongly with temperature(2) When configured for 1.1 V output swing(3) Under red illumination (780 nm)(4) Under white LED illumination(5) 60 MHz possible with slightly reduced image quality
9
CMOS Image Sensor
Features – 1312 x 1082 pixel resolution – 8 µm x 8 µm square pixel – Colour – Global shutter – Over 60% fill factor without microlenses – Integrated NIR cut-off filter(5)
– Dynamic range up to 60 dB – Up to 108 fps @ full resolution – Sequential, simultaneous or nondestructive
read out – Horizontal and vertical windowing – Flexible ROI and Multiple ROI – Integrated test pattern, temp. sensor and black
level reference
A1312C SeRIeS1.4 Megapixel colour CMOS image sensor
Spectral response of the Photonfocus A1312C CMOS image sensor
10
A1312C Series
A1312C-40 A1312C-160
Image Sensor
Technology CMOS active pixel (APS)Scanning system • Progressive scan • Arbitrary row adressing • Region of Interest (ROI) X and Y
• Multiple Region of Interest (MROI) X and Y • Multiple nondestructive readouts possibleOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixels (active pixels)Pixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Output swing 1.05 V (typical application)Random noise (RMS) 1.1 mVFPN (RMS, uncorrected) 13.5 mVDark current 0.65 fA/pixel @ 27°C (1)
Full well capacity 140 ke¯ (2)
Spectral range 390 to 670 nm (to 10 % of peak responsivity) (5) Responsivity 745 V/J/m² (3)
Quantum Efficiency > 40 % (3)
Sensitivity (for 10dB SNR) 4.4 µJ/m² (3)
Shutter efficiency 99.85 % (4)
Optical fill factor > 60 % (3)
Dynamic range 60 dB in linear mode Colour format RGB Bayer (raw)Characteristic curve LinearShutter mode Global shutterRead out mode Sequential or simultaneous read out (read out during exposure)Analog taps 1 4 (1 or 4 taps active)Pixel clock 40 MHz (6)
Maximum frame rate 27 fps @ max. resolution37 fps @ 1024 x 1024 resolution
108 fps @ max. resolution150 fps @ 1024 x 1024 resolution
Supply voltages 3.1 V, 3.3 V, 4.6 VPower consumption < 480 mW during full-speed read out < 600 mW during full-speed read outOperating temperature range Industrial (-20°C ... +85°C)Package 144-pin CQFPCover glass Integrated NIR cut-off filter(5)
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.0.2
(1) Varies strongly with temperature(2) Maximum, when configured for 1.1V output swing(3) Under red illumination (625 nm)(4) Under white LED illumination(5) A1312C image sensor available without NIR cut-off filter on request(6) 60 MHz possible with slightly reduced image quality
11
A2080 Series
CMOS Image Sensor
Features – 2080 x 2080 pixel resolution – 8 µm x 8 µm square pixel – Monochrome – Global shutter – Over 60% fill factor without microlenses – Good NIR response – Dynamic range up to 120 dB via LinLog®
– Up to 140 fps @ full resolution – Sequential, simultaneous or nondestructive
read out – Vertical windowing – Flexible ROI and Multiple ROI in Y direction – Integrated test pattern, temp. sensor and black
level reference
A2080 SeRIeS4 Megapixel monochrome CMOS image sensor
Spectral response of the Photonfocus A2080 CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
12
A2080-160 A2080-640
Image Sensor
Technology CMOS active pixel (APS)Scanning system • Progressive scan • Arbitrary row adressing • Region of Interest (ROI) in Y
• Multiple Region of Interest (MROI) in Y • Multiple nondestructive readouts possibleOptical format / diagonal 23.5 mm diagonal @ max. resolution (< 25 mm image circle)Resolution 2080 x 2080 pixels (active pixels)Pixel size 8 µm x 8 µmActive optical area 16.64 mm x 16.64 mm (maximum)Output swing 1.05 V (typical application)Random noise (RMS) 1.1 mVFPN (RMS, uncorrected) 13.5 mVDark current 0.65 fA/pixel @ 27°C (1)
Full well capacity 140 ke¯ (2)
Spectral range < 370 to 1000 nm (to 10 % of peak responsivity) Responsivity 819 V/J/m² (3)
Quantum Efficiency > 50 % (3)
Sensitivity (for 10dB SNR) 4.0 µJ/m² (3)
Shutter efficiency 99.85 % (4)
Optical fill factor > 60 % (3)
Dynamic range 60 dB in linear mode; 120 dB with LinLog® Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential or simultaneous read out (read out during exposure)Analog taps 4 16 (4 or 16 taps active)Pixel clock 40 MHz (5)
Maximum frame rate 35 fps @ max. resolution 140 fps @ max. resolutionSupply voltages 3.1 V, 3.3 V, 4.6 VPower consumption TBD mW during full-speed read out TBD mW during full-speed read outOperating temperature range Industrial (-20°C ... +85°C)Package 244-pin CQFPCover glass No cover glass
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.0.0
(1) Varies strongly with temperature(2) When configured for 1.1 V output swing(3) Under red illumination (625 nm)(4) Under white LED illumination(5) 60 MHz possible with slightly reduced image quality
13
OeM Camera Modules
For OEM that prefer to design their own camera solution but do not want to spend time on the sensor integration we offer all standard cameras as OEM camera modules.
All of the features and technical data are identical to the standard cameras except for the interface board which is not included. Thus making it a per-fect solution to interface to your own embedded system.
Customized OEM camera modules with different dimensions, components and features are another interesting option for OEM‘s. This option enables you to further speed up your time to market.
Please ask Photonfocus for solutions!
OeM CAMeRA MOdULeSPerfect Fit For embedded Solutions
OEM-D1024E-160-LC-12
OEM-D1312-160-LC-12
14
OEM Camera Modules
Board Level Cameras
For easier integration into tailored cus-tomer applications and especially where space or weight is a limiting factor we offer all our standard cameras as „Board Level“ models.
All of the features and technical data are identical to the standard cameras except for the mechanical dimensions. The footprint of these cameras is as small as 46 mm x 46 mm. The depth varies depending on the product type and chosen interface.
BOARd LeVeL CAMeRASCompact Solution For Application-Specific Systems
BL1-D1312-160-CL-12
BL1-D1024E-80-CL-12BL1-D1024E-40-CL-12
15
Board Level Cameras
CMOS Area Scan Cameras
Phot
onfo
cus
sens
or
Sens
or n
ame
/ge
nera
tion
Reso
lutio
n
Fram
e ra
te @
ful
l re
solu
tion
[fps
]
Dyn
amic
ran
ge [d
B]12
0 dB
= L
inLo
g®
Col
our
form
at
(Mon
ochr
om /
Col
our)
Inte
rfac
e (C
L /
PoC
L /
USB
/ G
igE)
max
. G
reys
cale
re
solu
tion
[bit]
max
. si
gnal
-to-
nois
e ra
tio (
SNR)
(1)
Glo
bal s
hutt
er
Nea
r In
frar
ed
Resp
onsi
vity
MV-D640(C)-33 - MT9V403 640 x 480 100 60 / / - / - / - 10 300 0
MV-D640(C)-66 - MT9V403 640 x 480 200 60 / / - / - / - 10 300 0
MV-D752E-40 A1024B / 2. 752 x 582 87 120 / - / - / / - 12 447 0
DS1-D1024-40 A1024B / 2. 1024 x 1024 37 60 / - / / / - 10 447 0
DS1-D1024-80 A1024B / 2. 1024 x 1024 75 60 / - / / - / - 10 447 0
DS1-D1024-160 A1024B / 2. 1024 x 1024 150 60 / - / / - / - 10 447 0
MV-D1024E-40 A1024B / 2. 1024 x 1024 37 120 / - / / / - 12 447 0
MV-D1024E-80 A1024B / 2. 1024 x 1024 75 120 / - / / - / - 12 447 0
MV-D1024E-160 A1024B / 2. 1024 x 1024 150 120 / - / / - / - 12 447 0
MV2-D1280-640 - MT9M413 1280 x 1024 488 59 / - / - / - / - 8 251 0
DS1-D1312-40 A1312 / 3. 1312 x 1082 27 60 / - / - / - / - 10 316 +
DS1-D1312-80 A1312 / 3. 1312 x 1082 55 60 / - / - / - / - 10 316 +
DS1-D1312-160 A1312 / 3. 1312 x 1082 108 60 / - / - / - / - 10 316 +
MV1-D1312-40 A1312 / 3. 1312 x 1082 27 120 / - / - / - / 12 316 +
MV1-D1312-80 A1312 / 3. 1312 x 1082 55 120 / - / - / - / 12 316 +
MV1-D1312-100 A1312 / 3. 1312 x 1082 68 120 / - - / - / - / 12 316 +
MV1-D1312-160 A1312 / 3. 1312 x 1082 108 120 / / - / - / - 12 316 +
MV1-D1312-240 A1312 / 3. 1248 x 1082 170 120 / - / - / - / - 8 316 +
MV1-D1312IE-40 A1312IE / 3. 1312 x 1082 27 120 / - / - / - / - 12 316 ++
MV1-D1312IE-160 A1312IE / 3. 1312 x 1082 108 120 / - / - / - / - 12 316 ++
MV1-D1312I-40 A1312I / 3. 1312 x 1082 27 120 / - / - / - / 12 316 +++
MV1-D1312I-80 A1312I / 3. 1312 x 1082 55 120 / - / - / - / 12 316 +++
MV1-D1312I-100 A1312I / 3. 1312 x 1082 68 120 / - - / - / - / 12 316 +++
MV1-D1312I-160 A1312I / 3. 1312 x 1082 108 120 / - / - / - / - 12 316 +++
MV1-D2080-160 A2080 / 3. 2080 x 2080 34 120 / - / - / - / - 12 316 +
MV1-D2080-240 A2080 / 3. 2080 x 2080 51 120 / - / - / - / - 8 316 +
(1) Computed as square root of full well capacity. Exact figures will be marginally lower.
16
Camera Selection Chart
Cameras with Image Preprocessing
Ph
oton
focu
s se
nsor
Sens
or n
ame
/ge
nera
tion
Reso
lutio
n
Fram
e ra
te @
ful
l re
solu
tion
[fps
]
Dyn
amic
ran
ge [d
B]12
0 dB
= L
inLo
g®
Col
our
form
at
(Mon
ochr
om /
Col
our)
Inte
rfac
e (C
L /
PoC
L /
USB
/ G
igE)
max
. G
reys
cale
re
solu
tion
[bit]
max
. si
gnal
-to-
nois
e ra
tio (
SNR)
(1)
Glo
bal s
hutt
er
Nea
r In
frar
ed
Resp
onsi
vity
MV1-D1024E-PP01-40 A1024B / 2. 1024 x 1024 37 120 / - / - / - / - 8 447 0
Smart CamerasSM2-D1024-80 A1024B / 2. 1024 x 1024 75 120 / - - / - / - / 12 447 0
SM2-D1312-80 A1312 / 3. 1312 x 1082 55 120 / - - / - / - / 12 316 +
SM2-D1312-JPEG-100 A1312 / 3. 1312 x 1082 68 120 / - - / - / - / 12 316 +
SM2-D1312-160 A1312 / 3. 1312 x 1082 108 120 / - - / - / - / 12 316 +
3d CamerasMV-D1024E-3D01-160 A1024B / 2. 1024 x 1024 150 120 / - / - / - / - 12 447 0
Version 1.2.1
electroluminescence CamerasEL1-D1312-160 A1312 / 3. 1312 x 1082 150 60 / - / - / - / - 12 316 +
(1) Computed as square root of full well capacity. Exact figures will be marginally lower.
17
CMOS Camera
Features – Aptina MT9V403 CMOS image sensor – 640 x 480 pixel resolution – Dynamic range up to 60 dB – Up to 200 fps @ full resolution – Global shutter – Monochrome and Colour – Standard features – CameraLink® interface – 10 bit greyscale resolution
MV-d640 SeRIeSHigh-Speed VGA
Spectral response of the Aptina MT9V403 CMOS image sensor
0
5
10
15
20
25
30
35
350 450 550 650 750 850 950 1050Wavelength [nm]
Quan
tum
Effic
iency
[%
]
0
5
10
15
20
25
350 450 550 650 750 850 950 1050
Wavelength [nm]
Quantu
m E
ffic
iency
[%
]
BlueGreen (B)Green (R)Red
Monochrome Colour
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
18
CMOS Area Scan Cameras
MV-D640 Series
MV-D640-33-CL-10MV-D640C-33-CL-10
MV-D640-66-CL-10MV-D640C-66-CL-10
Image Sensor
Image sensor Aptina MT9V403Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1/2” (7.92 mm diagonal)Resolution 640 x 480 pixelsPixel size 9.9 µm x 9.9 µmActive optical area 6.34 mm x 4.75 mmDark current -Full well capacity ~90 ke¯Spectral range < 400 to 1000 nmResponsivity 480 x 10³ DN / (J/m²) @ 630 nm / 8 bit / gain = 1 / monochrome
(approximately 2600 DN / (lux s) @ 630 nm / 8 bit / gain = 1 / monochrome)Quantum Efficiency -Optical fill factor 50 %Dynamic range Up to 60 dBColour format Monochrome or Colour (RGB Bayer)Characteristic curve LinearShutter mode Global shutterRead out mode Sequential read out or simultaneous read out (read out during exposure)
CameraExposure time 50 µs … 1.3 s / 10 µs stepsFrame rate 100 fps 200 fpsPixel clock 33 MHz 33 or 66 MHzCamera taps 1Greyscale resolution 8 bit / 10 bitFixed pattern noise (FPN) < 1.5 DN RMS @ 8 bit / gain = 1Analogue gain 1 … 8Digital gain -Configuration interface CL SERIAL (9600 Baud)Trigger modes • Free running (non triggered)
• External trigger inputFeatures • Region of Interest (ROI)
• External Clock availableInterface CameraLink® BaseOperating temperature 0°C ... +60°CPower supply +5 V DC (+10% / -5%) +5 V DC (+10% / -5%)Power consumption 1.5 W 3.3 WLens mount C-MountDimensions (H x W x L) 55 x 55 x 37 mm³ 55 x 55 x 48 mm³Mass 200 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)OS Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.6
19
CMOS Camera
Features – Photonfocus A1024B CMOS image sensor – 752 x 582 pixel resolution – Dynamic range up to 120 dB via LinLog®
– Up to 87 fps @ full resolution – Global shutter – Monochrome – Extended features – CameraLink® and USB 2.0 interface – 12 bit greyscale resolution
MV-d752e SeRIeSCCIR camera with proprietary Photonfocus sensor
Spectral response of the Photonfocus A1024B CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
20
MV-D752E Series
MV-D752E-40-CL-12 MV-D752E-40-U2-12
Image Sensor
Image sensor Photonfocus A1024B (2. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 2/3” (10.12 mm diagonal)Resolution 752 x 582 pixelsPixel size 10.6 µm x 10.6 µmActive optical area 8.0 mm x 6.2 mmDark current 2 fA/pixel @ 30°CFull well capacity ~200 ke¯Spectral range < 400 to 900 nmResponsivity 120 x 10³ DN / (J/m²) @ 610 nm / 8 bit / gain = 1
(approximately 350 DN / (lux s) @ 610 nm / 8 bit / gain = 1)Quantum Efficiency 45 % @ 550 nmOptical fill factor 35 % (geometrical)Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential read out
CameraExposure time 10 µs … 0.41 s / 25 ns stepsFrame rate 87 fpsPixel clock 40 MHzCamera taps 1Greyscale resolution 8 bit / 10 bit / 12 bitFixed pattern noise (FPN) < 1 DN RMS @ 8 bit / gain = 1 / offset correction ONAnalogue gain 1Digital gain 1 / 2 / 4Configuration interface CL SERIAL (9600 Baud)Trigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures • Region of Interest (ROI) • 16 Multiple ROI (MROI) • Decimation X and Y • Image correction • Look-up table (LUT)
• Constant frame rate • Image information• Extended trigger input and strobe output functionality
Interface CameraLink® Base USB 2.0Operating temperature 0°C ... +60°CPower supply +12 V DC (±10%)Power consumption 1.6 W 3.0 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 55 x 55 x 32 mm³ 55 x 55 x 49 mm³Mass 200 g 210 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)
USB 2.0: MicroDisplay (GUI) and PFLib (SDK)OS CL: Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
USB 2.0: win2k; winxp
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.5
21
CMOS Camera
Features – Photonfocus A1024B CMOS image sensor – 1024 x 1024 pixel resolution – Dynamic range up to 60 dB – Up to 150 fps @ full resolution – Global shutter – Monochrome – Standard features – CameraLink®, PoCL and USB 2.0 interface – 10 bit greyscale resolution
dS1-d1024 SeRIeS1 Megapixel resolution with proprietary Photonfocus sensor
Spectral response of the Photonfocus A1024B CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
22
DS1-D1024 Series
DS1-D1024-40-CL-10DS1-D1024-40-PC-10DS1-D1024-40-U2-10
DS1-D1024-80-CL-10DS1-D1024-80-PC-10
DS1-D1024-160-CL-10DS1-D1024-160-PC-10
Image Sensor
Image sensor Photonfocus A1024B (2. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (15.42 mm diagonal)Resolution 1024 x 1024 pixelsPixel size 10.6 µm x 10.6 µmActive optical area 10.9 mm x 10.9 mm (maximum)Dark current 2 fA/pixel @ 30°CFull well capacity ~200 ke¯Spectral range < 400 to 900 nmResponsivity 120 x 10³ DN / (J/m²) @ 610 nm / 8 bit / gain = 1
(approximately 350 DN / (lux s) @ 610 nm / 8 bit / gain = 1)Quantum Efficiency 45 % @ 550 nmOptical fill factor 35 % (geometrical)Dynamic range Up to 60 dBColour format MonochromeCharacteristic curve LinearShutter mode Global shutterRead out mode Sequential read out Sequential or simultaneous read out
(read out during exposure)
CameraExposure time 10 µs … 0.41 s / 25 ns steps 10 µs … 0.83 s / 50 ns steps 10 µs … 0.41 s / 25 ns stepsFrame rate 37 fps 75 fps 150 fpsPixel clock 40 MHz 80 MHzCamera taps 1 2Greyscale resolution 8 bit / 10 bitFixed pattern noise (FPN) < 2.5 DN RMS @ 8 bit / gain = 1Analogue gain 1Digital gain 1Configuration interface CL SERIAL (9600 Baud)Trigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures • Region of Interest (ROI) • Image correction • Image information
• Standard trigger input and strobe output functionalityInterface CameraLink® Base
PoCL - Power over CameraLink® BaseUSB 2.0
CameraLink® BasePoCL - Power over CameraLink® Base
Operating temperature 0°C ... +60°CPower supply +12 V DC (±10%)Power consumption 1.6 W (CL) / 3.0 W (USB 2.0) 3.0 W 3.2 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 55 x 55 x 32 mm³ (CL)
55 x 55 x 43 mm³ (USB 2.0)55 x 55 x 40 mm³
Mass 200 g 210 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)
USB 2.0: MicroDisplay (GUI) and PFLib (SDK)OS CL: Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
USB 2.0: win2k; winxp
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.5
2323
CMOS Camera
Features – Photonfocus A1024B CMOS image sensor – 1024 x 1024 pixel resolution – Dynamic range up to 120 dB via LinLog®
– Up to 150 fps @ full resolution – Global shutter – Monochrome – Extended features – CameraLink®, PoCL and USB 2.0 interface – 12 bit greyscale resolution
MV-d1024e SeRIeS1 Megapixel resolution with proprietary Photonfocus sensor
Spectral response of the Photonfocus A1024B CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
24
MV-D1024E Series
MV-D1024E-40-CL-12MV-D1024E-40-PC-12MV-D1024E-40-U2-12
MV-D1024E-80-CL-12MV-D1024E-80-PC-12
MV-D1024E-160-CL-12MV-D1024E-160-PC-12
Image Sensor
Image sensor Photonfocus A1024B (2. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (15.42 mm diagonal)Resolution 1024 x 1024 pixelsPixel size 10.6 µm x 10.6 µmActive optical area 10.9 mm x 10.9 mm (maximum)Dark current 2 fA/pixel @ 30°CFull well capacity ~200 ke¯Spectral range < 400 to 900 nmResponsivity 120 x 10³ DN / (J/m²) @ 610 nm / 8 bit / gain = 1
(approximately 350 DN / (lux s) @ 610 nm / 8 bit / gain = 1)Quantum Efficiency 45 % @ 550 nmOptical fill factor 35% (geometrical)Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential read out Sequential or simultaneous read out
(read out during exposure)
CameraExposure time 10 µs … 0.41 s / 25 ns steps 10 µs … 0.83 s / 50 ns steps 10 µs … 0.41 s / 25 ns stepsFrame rate 37 fps 75 fps 150 fpsPixel clock 40 MHz 80 MHzCamera taps 1 2Greyscale resolution 8 bit / 10 bit / 12 bitFixed pattern noise (FPN) < 1 DN RMS @ 8 bit / gain = 1 / offset correction ONAnalogue gain 1Digital gain 1 / 2 / 4Configuration interface CL SERIAL (9600 Baud) CL SERIAL (9600 or 57600 Baud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures • Region of Interest (ROI) • 16 Multiple ROI (MROI) • Decimation X(1) and Y • Image correction
• Look-up table (LUT) • Constant frame rate • Image information • Extended trigger input and strobe output functionality
Interface CameraLink® BasePoCL - Power over CameraLink® Base
USB 2.0
CameraLink® BasePoCL - Power over CameraLink® Base
Operating temperature 0°C ... +60°CPower supply +12 V DC (±10%)Power consumption 1.6 W (CL) / 3.0 W (USB 2.0) 3.0 W 3.2 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 55 x 55 x 32 mm³ (CL)
55 x 55 x 43 mm³ (USB 2.0)55 x 55 x 40 mm³
Mass 200 g 210 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)
USB 2.0: MicroDisplay (GUI) and PFLib (SDK)OS CL: Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
USB 2.0: win2k; winxp
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.8
(1) Feature only available for MV-D1024E-40 cameras
2525
CMOS Camera
Features – Aptina MT9M413 CMOS image sensor – 1280 x 1024 pixel resolution – Dynamic range up to 60 dB – Up to 490 fps @ full resolution – Global shutter – Monochrome – Extended features – CameraLink® Full interface – 10 bit greyscale resolution
MV2-d1280-640-CL-8Very fast 1.3 Megapixel resolution CMOS camera
Spectral response of the Aptina MT9M413 CMOS image sensor
0.00
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.10
200 300 400 500 600 700 800 900 1000 1100
Qu
an
tum
Eff
icie
ncy
Wavelength [nm]
Quantum Efficiency vs Wavelength
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
26
MV2-D1280-640
MV2-D1280-640-CL-8
Image sensor
Image sensor Aptina MT9M413Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1.3” (19.67 mm diagonal)Resolution 1280 x 1024 pixelsPixel size 12 µm x 12 µmActive optical area 15.36 mm x 12.29 mmDark current 0.6 fA/pixel @ 25°CFull well capacity ~63 ke¯Spectral range 350 to 900 nmResponsivity 400 DN / Lux sec @ 550 nm / 8 bit / gain = 1
(272’000 DN / J / m² @ 550 nm / 8 bit / gain = 1)Quantum Efficiency 8 % @ 500 nmOptical fill factor 40 % Dynamic range 59 dB in linear modeColour format MonochromeCharacteristic curve LinearShutter mode Global shutterRead out mode Sequential or simultaneous read out
CameraExposure time 10 µs … 100 ms / 2 ns stepsFrame rate 488 fpsPixel clock 66 MHz (10 tap mode), 82.5 MHz (8 tap mode)Camera taps 8 / 10Greyscale resolution 8 bitFixed pattern noise (FPN) <0.5% rms / 1.5 % p·pAnalogue gain 1Digital gain 1 / 2 / 4Configuration interface CL SERIAL (9600 or 57600 Baud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures • Region of Interest (ROI) • 16 Multiple ROI (MROI) • Decimation Y • Image correction • Look-up table (LUT)
• Constant frame rate • Image information • Extended trigger input and strobe output functionality
Interface CameraLink® FullOperating temperature 0°C ... +60°CPower supply +12 V DC (±10%)Power consumption 4.2 WLens mount M42x1, F-Mount, C-Mount (CS-Mount optional)Dimensions (H x W x L) 78 x 78 x 46.2 mm³Mass 374 gConformity CE / RoHS / WEEE / Shock and Vibration tests IEC 68-2-6, IEC 68-2-27, IEC 68-2-29Specials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)OS Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.5
2727
CMOS Camera
Features – Photonfocus A1312 CMOS image sensor – 1312 x 1082 pixel resolution – Good NIR response – Dynamic range up to 60 dB – Up to 108 fps @ full resolution – Global shutter – Monochrome – Standard features – CameraLink® interface – 10 bit greyscale resolution
dS1-d1312 SeRIeS1.4 Megapixel resolution with proprietary Photonfocus sensor
Spectral response of the Photonfocus A1312 CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
28
DS1-D1312 Series
DS1-D1312-40-CL-10 DS1-D1312-80-CL-10 DS1-D1312-160-CL-10
Image Sensor
Image sensor Photonfocus A1312 (3. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixelsPixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Dark current 0.65 fA/pixelFull well capacity ~100 ke¯Spectral range < 370 to 1000 nm (to 10 % of peak responsivity)Responsivity 210 x 10³ DN / (J/m²) @ 625 nm / 8 bit / gain = 1
(approximately 620 DN / (lux s) @ 625 nm / 8 bit / gain = 1)Quantum Efficiency > 50 %Optical fill factor > 60 %Dynamic range Up to 60 dBColour format MonochromeCharacteristic curve LinearShutter mode Global shutterRead out mode Sequential read out or simultaneous read out (read out during exposure)
CameraExposure time 10 µs … 1.68 s / 100 ns steps 10 µs … 0.83 s / 50 ns steps 10 µs … 0.41 s / 25 ns stepsFrame rate 27 fps 55 fps 108 fpsPixel clock 40 MHz 80 MHzCamera taps 1 2Greyscale resolution 8 bit / 10 bitFixed pattern noise (FPN) < 1 DN @ 8 bit / correction ONAnalogue gain 1Digital gain 1Configuration interface CL SERIAL (9600 Baud)Trigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures • Region of Interest (ROI) • Image correction
• Standard trigger input and strobe output functionalityInterface CameraLink® BaseOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption 2.5 W < 3.0 W < 3.3 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 60 x 60 x 45 mm³Mass 265 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)OS Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.5
29
CMOS Camera
Features – Photonfocus A1312 CMOS image sensor – 1312 x 1082 pixel resolution – Good NIR response – Dynamic range up to 120 dB via LinLog®
– Up to 170 fps @ full resolution – Global shutter – Monochrome – Extended features – CameraLink® and GigE interface – 12 bit greyscale resolution
MV1-d1312 SeRIeS1.4 Megapixel resolution with proprietary Photonfocus sensor
Spectral response of the Photonfocus A1312 CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
30
MV1-D1312 Series
MV1-D1312-40-CL-12MV1-D1312-40-GB-12
MV1-D1312-80-CL-12MV1-D1312-80-GB-12
MV1-D1312-160-CL-12MV1-D1312-100-GB-12
MV1-D1312-240-CL-8
Image Sensor
Image sensor Photonfocus A1312 (3. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixels 1248 x 1082 pixelsPixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Dark current 0.65 fA/pixelFull well capacity ~100 ke¯Spectral range < 370 to 1000 nm (to 10 % of peak responsivity) Responsivity 210 x 10³ DN / (J/m²) @ 625 nm / 8 bit / gain = 1
(approximately 620 DN / (lux s) @ 625 nm / 8 bit / gain = 1)Quantum Efficiency > 50 %Optical fill factor > 60 %Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®
Shutter mode Global shutterRead out mode Sequential read out or simultaneous read out (read out during exposure only in linear mode) for higher frame rates
CameraExposure time 10 µs … 1.68 s / 100 ns steps 10 µs … 0.83 s / 50 ns steps 10 µs … 0.67 s / 40 ns steps (GigE)
10 µs … 0.41 s / 25 ns steps (CL)10 µs … 0.279 s / 16.67 ns steps
Frame rate 27 fps 55 fps 68 fps (GigE) / 108 fps (CL) 170 fpsPixel clock 40 MHz 50 MHz (GigE) / 80 MHz (CL)Camera taps 1 2 3Greyscale resolution 8 bit / 10 bit / 12 bit 8 bitFixed pattern noise (FPN) < 1 DN @ 8 bit / correction ONAnalogue gain 1Digital gain 1 / 2 / 4 / 8Configuration interface CL SERIAL (9600, 57600 or 115‘200 Baud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger input • Software triggerFeatures • Region of Interest (ROI) • 512 Multiple ROI (MROI)(1) • Decimation Y(1) • Image correction • 2 Look-up tables (LUT)(1)
• Constant frame rate • Crosshair(1) • Convolver 3x3 • Temperature(1) • Image information• Extended trigger input and strobe output functionality
Interface CameraLink® Base or GigEOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption 2.5 W (CL) / < 4.5 W (GigE) < 3.0 W (CL) / < 5.0 W (GigE) < 3.3 W (CL) / < 5.2 W (GigE) < 5.2 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 60 x 60 x 45 mm³ (CL) / 60 x 60 x 99 mm³ (GigE)Mass 265 g (CL) / 465 g (GigE)Conformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)
GigE: graphical user interface GEV Player and SDKOS Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.2.3
(1) Features only available for CameraLink® cameras (for GigE cameras on request)
31
CMOS Camera
Features – Photonfocus A1312C CMOS image sensor – 1312 x 1082 pixel resolution – Integrated NIR cut-off filter(1)
– Dynamic range up to 60 dB – Up to 108 fps @ full resolution – Global shutter – Colour (RGB Bayer) – Standard features – CameraLink® interface – 12 bit output format
MV1-d1312C-160-CL-121.4 Megapixel resolution with proprietary Photonfocus sensor
Spectral response of the Photonfocus A1312C CMOS image sensor
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
32
MV1-D1312C-160
MV1-D1312C-160-CL-12
Image sensor
Image sensor Photonfocus A1312C (3. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixelsPixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Dark current 0.65 fA/pixelFull well capacity ~100 ke¯Spectral range 390 to 670 nm (to 10 % of peak responsivity)(1)
Responsivity 190 x 10³ DN / (J/m²) @ 625 nm / 8 bit / gain = 1(approximately 560 DN / (lux s) @ 625 nm / 8 bit / gain = 1)
Quantum Efficiency > 40 %Optical fill factor > 60 %Dynamic range 60 dB in linear modeColour format RGB Bayer (raw)Characteristic curve LinearShutter mode Global shutterRead out mode Sequential or simultaneous read out
(read out during exposure) for higher frame rates
CameraExposure time 10 µs … 0.41 s / 25 ns stepsFrame rate 108 fpsPixel clock 80 MHz Camera taps 2Greyscale resolution 8 bit / 10 bit / 12 bitFixed pattern noise (FPN) < 1 DN @ 8 bit / correction ONAnalogue gain 1Digital gain 1 / 2 / 4 / 8Configuration interface CL SERIAL (9600, 57600 or 115‘200 Baud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger input • Software triggerFeatures • Region of Interest (ROI) • 512 Multiple ROI (MROI) • Image correction • 2 Look-up tables (LUT)
• Constant frame rate • Digital fine gain • Colour fine gain • Temperature • Image information• Extended trigger input and strobe output functionality
Interface CameraLink® BaseOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption < 3.5 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 60 x 60 x 45 mm³Mass 265 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
Software
Camera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)OS Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.0.2
(1) A1312C image sensor available without NIR cut-off filter on request
33
CMOS Camera
Features – Photonfocus A1312I CMOS image sensor – 1312 x 1082 pixel resolution – Excellent NIR response – Dynamic range up to 120 dB via LinLog®
– Up to 108 fps @ full resolution – Global shutter – Monochrome – Extended features – CameraLink® and GigE interface – 12 bit greyscale resolution
MV1-d1312I SeRIeS1.4 Megapixel resolution with proprietary Photonfocus sensor
Spectral response of the Photonfocus A1312I CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
34
MV1-D1312I Series
MV1-D1312I-40-CL-12MV1-D1312I-40-GB-12
MV1-D1312I-80-CL-12MV1-D1312I-80-GB-12
MV1-D1312I-160-CL-12MV1-D1312I-100-GB-12
Image Sensor
Image sensor Photonfocus A1312I (3. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixelsPixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Dark current 1.15 fA/pixelFull well capacity ~100 ke¯Spectral range < 370 to 1100 nm (to 10 % of peak responsivity) Responsivity 300 x 10³ DN / (J/m²) @ 850 nm / 8 bit / gain = 1Quantum Efficiency > 50 %Optical fill factor > 60 %Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®
Shutter mode Global shutterRead out mode (read out during exposure only in linear mode) for higher frame rates
CameraExposure time 10 µs … 1.68 s / 100 ns steps 10 µs … 0.83 s / 50 ns steps 10 µs … 0.67 s / 40 ns steps (GigE)
10 µs … 0.41 s / 25 ns steps (CL)Frame rate 27 fps 55 fps 68 fps (GigE) / 108 fps (CL)Pixel clock 40 MHz 50 MHz (GigE) / 80 MHz (CL)Camera taps 1 2Greyscale resolution 8 bit / 10 bit / 12 bitFixed pattern noise (FPN) < 1 DN @ 8 bit / correction ONAnalogue gain 1Digital gain 1 / 2 / 4 / 8Configuration interface Gigabit Ethernet / CL SERIAL (9600, 57600 or 115‘200 Baud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger input • Software triggerFeatures • Region of Interest (ROI) • 512 Multiple ROI (MROI)(1) • Decimation Y(1) • Image correction • 2 Look-up tables (LUT)(1)
• Constant frame rate • Crosshair(1) • Convolver 3x3 • Temperature(1) • Image information• Extended trigger input and strobe output functionality
Interface CameraLink® Base or GigEOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption 2.5 W (CL) / < 4.5 W (GigE) < 3.0 W (CL) / < 5.0 W (GigE) < 3.3 W (CL) / < 5.2 W (GigE)Lens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 60 x 60 x 45 mm³ (CL) / 60 x 60 x 99 mm³ (GigE)Mass 265 g (CL) / 465 g (GigE)Conformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)
GigE: graphical user interface GEV Player and SDKOS Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.7
(1) Features only available for CameraLink® cameras (for GigE cameras on request)
3535
CMOS Camera
Features – Photonfocus A1312IE CMOS image sensor – 1312 x 1082 pixel resolution – Very good NIR response – Dynamic range up to 120 dB via
LinLog®
– Up to 108 fps @ full resolution – Global shutter – Monochrome – Extended features – CameraLink®
– 12 bit greyscale resolution
MV1-d1312Ie SeRIeS1.4 Megapixel resolution with proprietary Photonfocus sensor
Spectral response of the Photonfocus A1312Ie CMOS image sensor
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
36
MV1-D1312IE Series
MV1-D1312IE-40-CL-12 MV1-D1312IE-160-CL-12
Image Sensor
Image sensor Photonfocus A1312IE (3. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixelsPixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Dark current 0.65 fA/pixelFull well capacity ~100 ke¯Spectral range < 370 to 1050 nm (to 10 % of peak responsivity) Responsivity 280 x 10³ DN / (J/m²) @ 850 nm / 8 bit / gain = 1Quantum Efficiency > 45 %Optical fill factor > 60 %Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®
Shutter mode Global shutterRead out mode Sequential read out or simultaneous read out (read out during exposure only in linear mode) for higher frame rates
CameraExposure time 10 µs … 1.68 s / 100 ns steps 10 µs … 0.41 s / 25 ns stepsFrame rate 27 fps 108 fpsPixel clock 40 MHz 80 MHzCamera taps 1 2Greyscale resolution 8 bit / 10 bit / 12 bitFixed pattern noise (FPN) < 1 DN @ 8 bit / correction ONAnalogue gain 1Digital gain 0.1 to 15.99 (Fine Gain)Configuration interface CL SERIAL (9600, 57600 or 115‘200 Baud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger input • Software triggerFeatures • Region of Interest (ROI) • 512 Multiple ROI (MROI) • Decimation Y • Image correction • 2 Look-up tables (LUT)
• Constant frame rate • Crosshair • Convolver 3x3 • Temperature • Image information• Extended trigger input and strobe output functionality
Interface CameraLink® BaseOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption 2.5 W < 3.3 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 60 x 60 x 45 mm³Mass 265 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)OS Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.0.0
37
MV1-D2080 Series
CMOS Camera
Features – Photonfocus A2080 CMOS image sensor – 2080 x 2080 pixel resolution – Good NIR response – Dynamic range up to 120 dB via LinLog®
– Up to 51 fps @ full resolution – Global shutter – Monochrome – Extended features – CameraLink® interface – 12 bit greyscale resolution – Exceptional SNR
MV1-d2080 SeRIeS4 Megapixel resolution with proprietary Photonfocus sensor
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
Spectral response of the Photonfocus A2080 CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
38
MV1-D2080-160-CL-12 MV1-D2080-240-CL-8
Image Sensor
Image sensor Photonfocus A2080 (3. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 23.5 mm diagonal @ max. resolution ( < 25 mm image circle)Resolution 2080 x 2080 pixelsPixel size 8 µm x 8 µmActive optical area 16.64 mm x 16.64 mm (maximum)Dark current 0.65 fA/pixelFull well capacity ~90 ke¯ (Max SNR > 300:1)Spectral range < 370 to 1000 nm (to 10 % of peak responsivity) Responsivity 210 x 10³ DN / (J/m²) @ 625 nm / 8 bit / gain = 1
(approximately 620 DN / (lux s) @ 625 nm / 8 bit / gain = 1)Quantum Efficiency > 50 %Optical fill factor > 60 %Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®
Shutter mode Global shutterRead out mode Sequential read out or simultaneous read out (read out during exposure only in linear mode) for higher frame rates
CameraExposure time 10 µs … 0.41 s / 25 ns steps 10 µs … 0.279 s / 16.67 ns stepsFrame rate 34 fps 51 fpsPixel clock 80 MHzCamera taps 2 3Greyscale resolution 8 bit / 10 bit / 12 bit 8 bitFixed pattern noise (FPN) < 1 DN @ 8 bit / correction ONAnalogue gain 1Digital gain Digital fine gain (0.1 … 15.9 / 0.001 steps)Configuration interface CL SERIAL (up to 1.5 MBaud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger input • Software triggerFeatures • Region of Interest (ROI) • 512 Multiple ROI (MROI) • Decimation Y • Image correction • 2 Look-up tables (LUT)
• Constant frame rate • Convolver • Crosshair • Temperature & Image information• Extended trigger input and strobe output functionality • Status line
Interface CameraLink® BaseOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption < 5 W (over full operating range)Lens mount M42x1, F-Mount, C-Mount 1.3“Dimensions (H x W x L) 60 x 60 x 38 mm³Mass 222 gConformity CE / RoHS / WEEESpecials Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)OS Windows and Linux (32 & 64 Bit); other OS (QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.0.3
39
CMOS Camera
Features – Photonfocus A1024B CMOS image sensor – 1024 x 1024 pixel resolution – Real time image preprocessing on camera
FPGA – Dynamic range up to 120 dB via
LinLog®
– Up to 37 fps @ full resolution – Global shutter – Monochrome – CameraLink® interface – 12 bit greyscale resolution
MV-d1024e-PP01-40-CL-81 Megapixel camera with extended image preprocessing options
Advantages – Reduction of vision system computer CPU load – Removed reliance on specialised framegrabber or HW accelerators – Pixel Professor™ Lab a free GUI for easy graphical programming of the
camera FPGA – Common image preprocessing operators (e.g. Median, Convolver 3x3, …)
Pixel Professor™ Lab GUI
40
Cameras with Image Preprocessing
MV1-D1024E-PP01-40
MV-D1024E-PP01-40-CL-8
Image sensor
Image sensor Photonfocus A1024B (2. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (15.42 mm diagonal)Resolution 1024 x 1024 pixelsPixel size 10.6 µm x 10.6 µmActive optical area 10.9 mm x 10.9 mm (maximum)Dark current 2 fA/pixel @ 30°CFull well capacity ~200 ke¯Spectral range < 400 to 900 nmResponsivity 120 x 10³ DN / (J/m²) @ 610 nm / 8 bit / gain = 1
(approximately 350 DN / (lux s) @ 610 nm / 8 bit / gain = 1)Quantum Efficiency 45 % @ 550 nmOptical fill factor 35 % (geometrical)Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential or simultaneous read out (read out during exposure)
CameraExposure time 10 µs … 0.41 s / 25 ns stepsFrame rate 37 fpsPixel clock 40 MHzCamera taps 1Greyscale resolution 8 bitFixed pattern noise (FPN) < 1 DN RMS @ 8 bit / gain = 1 / offset correction ONAnalogue gain 1Digital gain 1 / 2 / 4Configuration interface CL SERIAL (9600 Baud)Trigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures • Region of Interest (ROI) • 16 Multiple ROI (MROI) • Decimation X and Y • Image correction • Look-up table (LUT)
• Constant frame rate • Image information • Convolvers • Median Filters • Pixel arithmetic • Pipeline Processors • Extended trigger input and strobe output functionality
Interface CameraLink® BaseOperating temperature 0°C ... +60°CPower supply +12 V DC (±10%)Power consumption 2.6 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 55 x 55 x 40 mm³Mass 220 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PFRemote™ graphical user interface (GUI) and PFLib (SDK)Pixel Professor™ configuration Pixel Professor™ LabOS win2k; winxp; winvista; other OS (Linux, QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.5
41
CMOS Smart Camera
Features – Photonfocus A1024B CMOS image sensor – 1024 x 1024 pixel resolution – Programmable Texas Instruments DSP – HALCON Embedded compatible – Dynamic range up to 120 dB via
LinLog®
– Up to 75 fps @ full resolution – Global shutter – Monochrome – GigE interface – 12 bit greyscale resolution
SM2-d1024-80-GB-121 Megapixel smart camera with programmable dSP
Compatible with
Spectral response of the Photonfocus A1024B CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
42
Smart Cameras
SM2-D1024-80
SM2-D1024-80-GB-12VisionCam PS Type 1*
Image sensor
Image sensor Photonfocus A1024B (2. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (15.42 mm diagonal)Resolution 1024 x 1024 pixelsPixel size 10.6 µm x 10.6 µmActive optical area 10.9 mm x 10.9 mm (maximum)Dark current 2 fA/pixel @ 30°CFull well capacity ~200 ke¯Spectral range < 400 to 900 nmResponsivity 120 x 10³ DN / (J/m²) @ 610 nm / 8 bit / gain = 1
(approximately 350 DN / (lux s) @ 610 nm / 8 bit / gain = 1)Quantum Efficiency 45 % @ 550 nmOptical fill factor 35 % (geometrical)Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential or simultaneous read out (read out during exposure)
CameraExposure time 10 µs … 0.83 s / 50 ns stepsFrame rate 75 fpsPixel clock 40 MHzCamera taps 2 (internal)Greyscale resolution 8 bit / 10 bit / 12 bitFixed pattern noise (FPN) < 1 DN RMS @ 8 bit / gain = 1 / offset correction ONAnalogue gain 1Digital gain 1 / 2 / 4Configuration interface Built-in WebserverTrigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures • Region of Interest (ROI) • 16 Multiple ROI (MROI) • Decimation Y • Image correction • Look-up table (LUT)
• Constant frame rate • Image information • Realtime clock • FTP Server• Extended trigger input and strobe output functionality
CPU / RAM / Storage Texas Instruments TMS320 C6415 @ 1GHz, 8000 MIPS / 256 MB SDRAM / 2 GB SD CardInterface GigEOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption 8.0 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 60 x 60 x 127 mm³Mass 532 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os; JTAG, RS232 Interface, RS422 Interface
SoftwareCamera control Built-in webserverDSP Development tools Texas Instruments Code Composer Studio 3.3, HALCON Embedded
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.8
* Product name used by Imago Technologies
43
CMOS Smart Camera
Features – Photonfocus A1312 CMOS image sensor – 1312 x 1082 pixel resolution – Programmable Texas Instruments DSP – HALCON Embedded compatible – Dynamic range up to 120 dB via
LinLog®
– Up to 108 fps @ full resolution – JPEG compression @ 68 fps(1)
– Global shutter – Monochrome – GigE interface – 12 bit greyscale resolution
SM2-d1312 SeRIeS1.4 Megapixel smart camera with programmable dSP
Compatible with
Spectral response of the Photonfocus A1312 CMOS image sensor
0%
10%
20%
30%
40%
50%
60%
200 300 400 500 600 700 800 900 1000 1100
Qu
antu
m E
ffic
ien
cy
Wavelength [nm]
Quantum Efficiency vs. Wavelength
44
SM2-D1312 Series
SM2-D1312-80-GB-12VisionCam PS Type 2*
SM2-D1312-JPEG-100-GB-12VisionCam PS Type 2*
SM2-D1312-160-GB-12VisionCam PS Type 2*
Image sensor
Image sensor Photonfocus A1312 (3. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (13.6 mm diagonal) maximum resolution
2/3” (11.6 mm diagonal) 1024 x 1024 resolutionResolution 1312 x 1082 pixelsPixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Dark current 0.65 fA/pixelFull well capacity ~100 ke¯Spectral range < 370 to 1000 nm (to 10 % of peak responsivity)Responsivity 210 x 10³ DN / (J/m²) @ 625 nm / 8 bit / gain = 1
(approximately 620 DN / (lux s) @ 625 nm / 8 bit / gain = 1)Quantum Efficiency > 50 %Optical fill factor > 60 %Dynamic range 60 dB in linear mode; 120 dB with
LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®
Shutter mode Global shutterRead out mode Sequential or simultaneous read out
(read out during exposure only in linear mode) for higher frame rates
CameraExposure time 10 µs … 0.83 s / 50 ns steps 10 µs … 0.67 s / 40 ns steps 10 µs … 0.41 s / 25 ns stepsFrame rate 55 fps 68 fps 108 fpsPixel clock 40 MHz 50 MHz 80 MHzCamera taps 2 (internal)Greyscale resolution 8 bit / 10 bit / 12 bit 8 bitFixed pattern noise (FPN) < 1 DN RMS @ 8 bit / gain = 1 / offset correction ONAnalogue gain 1Digital gain 1 / 2 / 4 / 8Configuration interface Built-in WebserverTrigger modes • Free running (non triggered) • DSP controlled trigger • External trigger inputFeatures • Region of Interest (ROI) • 512 Multiple ROI (MROI) • Decimation Y • Image correction • 2 Look-up tables (LUT)
• Constant frame rate • Crosshair • Convolver 3x3 • Temperature • Image information • Realtime clock • JPEG Compression(1) • FTP Server • Extended trigger input and strobe output functionality
CPU / RAM / Storage Texas Instruments TMS320 C6415 @ 1GHz, 8000 MIPS / 256 MB SDRAM / 2 GB SD Card(2)
Interface GigEOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption 10 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 60 x 60 x 137 mm³Mass 572 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os; JTAG, RS232 Interface, RS422 Interface
SoftwareCamera control Built-in webserverDSP Development tools Texas Instruments Code Composer Studio 3.3, HALCON Embedded
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG. Version 1.1.9
(1) Feature only available for SM2-D1312-JPEG-100-GB-12 camera (for other cameras on request)(2) DSP TI TMS320 C6455 @ 1.2GHz, 9600 MIPS / 512 MB SDRAM (available on request)
* Product name used by Imago Technologies
45
CMOS 3d Camera
Features – Photonfocus A1024B CMOS image sensor – 1024 x 1024 pixel resolution – Realtime laserline Peak Detection algorithm
on camera – Dynamic range up to 120 dB via
LinLog®
– Up to 2500 profiles/s @ 1024 x 32 pixel resolution
– Global shutter – Monochrome – CameraLink® interface – 12 bit greyscale resolution
MV-d1024e-3d01-160-CL-121 Megapixel 3d camera for laser triangulation applications
Advantages – No additional calculations on CPU – Reduction of vision system computer CPU load – PF 3D Suite a free GUI for an easy system set up and visualisation of 3D scans – Higher accuracy and robustness through new Peak Detection algorithm
Standard camerawith linear response (< 60 dB)
Photonfocus CMOS camera with LinLog® response (120 dB)
PF 3d Suite
COMPATIBLE WITH
LabVIEWNATIONAL INSTRUMENTS
Compatible with
46
3D Cameras
MV-D1024E-3D01-160
MV-D1024E-3D01-160-CL-12
Image sensor
Image sensor Photonfocus A1024B (2. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (15.42 mm diagonal)Resolution 1024 x 1024 pixelsPixel size 10.6 µm x 10.6 µmActive optical area 10.9 mm x 10.9 mm (maximum)Dark current 2 fA/pixel @ 30°CFull well capacity ~200 ke¯Spectral range < 400 to 900 nmResponsivity 120 x 10³ DN / (J/m²) @ 610 nm / 8 bit / gain = 1
(approximately 350 DN / (lux s) @ 610 nm / 8 bit / gain = 1)Quantum Efficiency 45 % @ 550 nmOptical fill factor 35 % (geometrical)Dynamic range 60 dB in linear mode; 120 dB with LinLog®
Colour format MonochromeCharacteristic curve Linear, LinLog®, SkimmingShutter mode Global shutterRead out mode Sequential or simultaneous read out (read out during exposure)
CameraExposure time 10 µs … 0.41 s / 25 ns stepsFrame rate 150 fps @ full resolution / 2500 fps @ 1024 x 32 resolution / 3900 fps @ 512 x 32 resolutionPixel clock 80 MHzCamera taps 2Greyscale resolution 8 bit / 10 bit / 12 bitFixed pattern noise (FPN) < 1 DN RMS @ 8 bit / gain = 1 / offset correction ONAnalogue gain 1Digital gain 1 / 2 / 4Configuration interface CL SERIAL (9600 or 57600 Baud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures • Region of Interest (ROI) • 16 Multiple ROI (MROI) • Decimation Y • Image correction • Look-up table (LUT)
• Constant frame rate • Image information • Peak Detector• Extended trigger input and strobe output functionality
Interface CameraLink® BaseOperating temperature 0°C ... +50°CPower supply +12 V DC (±10%)Power consumption 3.7 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 55 x 55 x 40 mm³Mass 210 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control PF 3D Suite graphical user interface (GUI) and PF3DLib (SDK)OS win2k; winxp; winvista; other OS (Linux, QNX, etc) on request
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.6
4747
CMOS Camera
Features – Photonfocus A1312 CMOS image sensor – 1312 x 1082 pixel resolution – Good NIR response – Uncooled CMOS camera – Designed for electroluminescence
applications – Global shutter – Monochrome – CameraLink® interface – 12 bit greyscale resolution
eL1-d1312-160-CL-12electroluminescence camera with nIR sensitive Photonfocus sensor
Sample image of solar cell inspection
48
Electroluminescence Cameras
EL1-D1312-160
EL1-D1312-160-CL-12
Image Sensor
Image sensor Photonfocus A1312 (3. Generation)Technology CMOS active pixel (APS)Scanning system Progressive scanOptical format / diagonal 1” (13.6 mm diagonal) maximum resolutionResolution 1312 x 1082 pixelsPixel size 8 µm x 8 µmActive optical area 10.48 mm x 8.64 mm (maximum)Dark current 0.65 fA/pixelFull well capacity ~100 ke¯ (nominal)Spectral range < 370 to 1000 nm (to 10 % of peak responsivity) Responsivity AdjustableQuantum Efficiency > 50 %Optical fill factor > 60 %Dynamic range TBDColour format MonochromeCharacteristic curve LinearShutter mode Global shutter
CameraExposure time 10 ms .... 1.6 s / 100 ns stepsFrame rate 5 fpsPixel clock 80 MHzCamera taps 2Greyscale resolution 12 bitConfiguration interface CL SERIAL (9600 or 57600 Baud, user selectable)Trigger modes • Free running (non triggered) • Interface trigger • External trigger inputFeatures Optimized for electroluminescence applicationsInterface CameraLink® BaseOperating temperature 0°C ... +40°CPower supply +12 V DC (±10%)Power consumption < 3.3 WLens mount C-Mount (CS-Mount optional)Dimensions (H x W x L) 60 x 60 x 45 mm³Mass 265 gConformity CE / RoHS / WEEESpecials Adjustable backfocus; Opto-isolated I/Os
SoftwareCamera control Electroluminescence API (PfEL1Lib )OS win2k; winxp; winvista
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.3
4949
Accessories
Features – CameraLink® extension up to 40 m – 100% CameraLink® compatible – Compact & robust industrial housing – Active clock and data regeneration – With “zero skew” – Bridging of long distances with – CameraLink® interface – No cable insertion losses – Automatic stand-by mode – Power-up failsafe – Plug and play
CAMeRALInK® RePeATeRLink to the Success
Worst Case
Typical Case
Best Case
100806040200
0
10
20
30
40
Pixel Clock / MHz
Distance vs Pixel Clock
Cab
le L
eng
th p
er S
ide
/ m
50
60
Range of CameraLink® with AWG 28 standard cable
50
Accessories
CameraLink® Repeater
Digipeater® CLB26
Image Sensor
Cable length Up to 20 m per side @ 20 MHzDigital interface CameraLink® Base and Medium ConfigurationMax. pixel clock 85 MHz @ 8 m cable length (with AWG 28 cable)Min. pixel clock 20 MHz @ 20 m cable length (with AWG 28 cable)Features • Power-up failsafe • Active clock and data regeneration with “zero skew”
• Hot swappable plug • Automatic stand-by modeOperating temperature 0 °C ... + 60 °CPower supply + 5 V … + 8 V DC (+/-10 %)Power consumption 1.0 WInterface connector MDR26 (CameraLink®)Power connector Binder connector series 712Dimensions 57 x 36 x 107 mm³Mass 160 gConformity CE / RoHS / WEE
All information provided in this flyer is believed to be accurate and reliable. No responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to make changes to this information without notice. Reproduction of this flyer in whole or in part, by any means, is prohibited without prior permission having been obtained from Photonfocus AG.
Version 1.1.0
51
Address Photonfocus AG Bahnhofplatz 10 8853 Lachen Schweiz
Telephone main office +41 (0)55 451 00 00
Fax main office +41 (0)55 451 00 01
email general [email protected] sales [email protected] support [email protected]
Internet website www.photonfocus.com
Version 2.2.1
