CLIENT: OCEANRIG VESSEL: CORCOVADO · section 01 – executive summary report section 02 – 196 – ccertificate of thorough examination – riser bridle section 03 – 313.331 –

RP-QT-127B Rev.0

QUALITECH INSPEÇÃO, REPARO E MANUTENÇÃO LTDA.

GENERAL NDT INSPECTION

CLIENT: OCEANRIG

VESSEL: CORCOVADO

PO N°: ORBRZ-0055-2015 WO N°: 1173-1

Date: 27/09/2015 Version: Original Volume: 1 of 1

RP-QT-127B Rev.0

CONTENT

SECTION 01 – EXECUTIVE SUMMARY REPORT

SECTION 02 – 196 – CCERTIFICATE OF THOROUGH EXAMINATION – RISER BRIDLE

SECTION 03 – 313.331 – LIQUID PENETRAN REPORT – ADARTOR BUSHING ROTARY

TABLE MAIN WELL

SECTION 04 – 315 – WALL THICKNESS REPORT – APV’s LEVEL 1 & 2

SECTION 05 – 326.300 – WALL THICKNESS REPORT – VACUUM DEGASSER

SECTION 06 – 334.911 – MPI REPORT – RISER RUNNING TOOL

SECTION 07 – 335.311 – MPI REPORT – FRAME

SECTION 08 – 335.321 – MPI & EDDY CURRENT REPORT – SPIDER

SECTION 09 – 335.935.005 – MPI REPORT – RISER RUNNING TOOL

SECTION 10 – 335.935.010 – MPI REPORT – RISER RUNNING TOOL

SECTION 11 – 345.600 – MPI REPORT – BAILS

SECTION 12 – 361.100 – MPI REPORT – CRANE KNUCKLE BOOM #1




SECTION 16 – NO SFI – CERTIFICATE OF TOUROUGH EXAMINATION – WIRE ROPE,

SHACKLES AND RUNNING TOOL

SECTION 17 – NO SFI – MPI REPORT – CONTAINER PAD EYE

RP-QT-127B Rev.0

SECTION 18 – NO SFI – PHOTOGRAPHIC REPORT – WATER LEAK PIPE

SECTION 19 – TECHNICIAN CERTIFICATE

SECTION 20 – COMPANY CERTIFICATE

Page 1 of 1

Qualitech Inspeção, Reparo e Manutenção Ltda. Estrada do Engenho D’Água,1330, Box01-C, Anil, Jacarepaguá–RJ – Brasil CEP 22765-240

www.qualitechirm.com Quality for safety

RP-QT-072B Rev.2

CERTIFICATE OF TEST AND THOROUGH EXAMINATION

Certificate Number: CTE-1173-052

Customer: Ocean Rig Color Code: Green

Location: Corcovado Inspection Procedure: ISO 2415

SFI Code: 196 Client WO: 2015-08327

Date of Examination: 11/10/2015 Manufacture: Certex

Date of Next Examination: 09/04/2016 Equipment Status: Ok

Identity No Description & Detail Of Equipment Location SWL Test Proof

Load

447842-1

447842-2

48mm x 27 mtrs 6x36 IWRC, Galvanized, Two Legs Wire Rope Sling with Master

Link and Thimble Eyes on Top and Legs Ending with Swivel Eye Latch Hook and

Thimble Eye

48mm x 27 mtrs 6x36 IWRC, Galvanized, Two Legs Wire Rope Sling with Master

Link and Thimble Eyes on Top and Legs Ending with Swivel Eye Latch Hook and

Thimble Eye

Riser Deck

Riser Deck

43 t /30°

43 t /30°

N/A

N/A

General Comment: NO DEFECTS WERE FOUND AT TIME OF THE INSPECTION.

I certify on behalf of the firm, Company, association or technician named below that the items described herein were tested and thereafter examined and were found to be free from cracks, flaws or other defects

Name / Qualification:

Bruno Cerri

Signed / Stamp:

Date of Inspection:

11/10/2015

Approved by:

This certification or Report is granted or issued subject to the condition that it is understood and agreed upon that nothing herein shall be deemed to relieve any designer,manufacture, seller, supplier repairer, or operator of any warranty, express or implied and Qualitech. Liability shall be limited to the acs and omissions of it's employees, agents and subcontractors. Under no circumstances shall Qualitech be liable for any injury or damage to any person or property occurring by reason of negligent operation, misuse of or any defect in material, machinery, equipment, or other items other than defects in items actually inspected by Qualitech and ascertainable by normally accepted testing standards, or defects reflected in documents reviewed by Qualitech and which are covered by this certificate or report.The certificate or report and the recommendations contained in it are based upon the conditions and practices observed and information made available to Qualitech personnel. The report does not purport to list all hazards or faulty conditions not to indicate that other hazards or faulty conditions exist. Severety ratings in the report are based on the criteria shown in this report and are intended as a guideline only. No responsability is assumed for the control or correction of conditions.

Page 1 of 2



RP-QT-102B Rev.3

LIQUID PENETRANT INSPECTION REPORT

Client: Ocean Rig Date: 12/10/2015 Qualitech WO:1173 Report Number: DP-1173-003

P.O. Nr: N/A Location: Corcovado Inspection Procedure: PI-QT-04 Rev.1

SFI Code: 313.331 Client WO: 2015-07806 Surface: Clean

Equipment Description: Adaptor Bushing Rotary Table Main Well Aft Qty: 6 Size: N/A

Serial Number: N/A Reference Drawing N°: N/A

Specification: ASME Section V Material: Stainless steel Manufacture: N/A

Comment: Area Inspected: As per clients request a Visual and Liquid penetrating Inspection was carried out on 100% off the accessible critical and stress areas of the Adaptor Bushing Rotary Table Main Well Aft Result: No defects were found at time of inspection Conclusion: Acceptable to Specification Recommendations: Release for Use Continuation Attached: Yes

Name / Qualification: Bruno Cerri

SNT/LP-5655

Signed / Stamp: Date of Inspection: 12/10/2015

Approved By:

Test Method

Test Medium x Visible Fluorescent

Penetrant Type: VP 30 Water Washable:

Solvent removable :

Post emulsifier :

Batch Nr:

Cleaner type: Water

Developer: D 70

Black Light Unit: N/A

Maker: Metal Check

Maker: N/A

Maker: Metal Check

Maker: N/A

Batch Nr: 20890

Batch Nr:

Batch Nr: 21035

Serial Nr:

Component Temp: ≥4ᵒC to ≤40ᵒC Dwell Time: ≥10 min to≤60min Dev. Time: ≥10 min to ≤60min

UV-A Irradiance: uw/cm2 Ambient Light Level: 1500 Lux

Page 2 of 2



RP-QT-102B Rev.3

LIQUID PENETRANT INSPECTION REPORT

Client: Ocean Rig Report Number: DP-1173-003

P.O. Nr: N/A WO: 1173 Location: Corcovado

Item: Adaptor Bushing Rotary Table Main Well Aft

Inspection Details: As per clients request a Visual and liquid penetrating inspection was carried out on 100% of the accessible critical area of the Eye Bolt

Name & Qualification: Bruno Cerri

SNT/PT-5655

Signed/Stamp:

Date of Inspection: 12/10/2015

Approved By:

RP-QT-134 Rev.1

Project:

Location:

DW N°:

Description:

To:From:

Date:

Note:The Locator Drawing are for reference only & not to a actual scale size.

Rev.:1Scale: N/A

Legend

Point

APV´S VESSEL

Test Point Orientation

AB

C

AB

CB

A

CDD D

WO N°:

Apv´s

Sub Sea

2015-08331-DW-24

Apv´s Room Apv´s Room

Wall Thickness Survey

04/10/2015

QT-1153

0

AFTFoward 1A2A3A

Front View

Customer: Report No: 2015-08331-WT-024

W.O. No: Steel Grade: Mat / Velocity: Cromo e Molibdenio/5920m/s

Pipe Line:

Work Area:

N°Original

Thickness

Class Minimum Thickness

(mm)

Test Point O.D

Actual W.T. (2015)

Diminuation (%) 2015

Actual W.T. (2016)


Actual W.T. (2017)


Max Allow Diminuation

(mm)


(%)Test Point Type

1A 12,5mm 559mm 14,4mm Pressure Vessel

1B 12,5mm 559mm 14,0mm Pressure Vessel

1C 12,5mm 559mm 14,5mm Pressure Vessel

1D 12,5mm 559mm 14,1mm Pressure Vessel









Substantial Corrosion

Below Class Minimum

Bruno Cerri

Comments: Wall Thickness Class Minimum Calculated in accordance with the client class requirements. Legend:

Inspector's Signature Date: Surveyor's Signature Approved By:04/10/2015

Design Pressure (psi): 207 Bar Qualification: SNT-TC-1A-UT 3269APV´S Room Lv2

APV-06 Flow Sheet / Dr'g No: 2015-08331-DW-24

INTEGRATE MANAGEMENT SYSTEM Page 1 of 32

Title:

WALL THICKNESS PIPE LINE SURVEY REPORT

Inspector:

N/A

Ocean Rig SFI Code: 315 Client WO: 2015-08331

1173 Line Number: ASTM A519 Gr 4130

Location: Mylos

RP-QT-116 Rev.02


W.O. No: Steel Grade: Mat / Velocity: Cromo e Molibideno/5920m/s

Pipe Line:

Work Area:

N°Original

Thickness


(mm)

Test Point O.D

Actual W.T. (2015)


Actual W.T. (2016)


Actual W.T. (2017)



(mm)


(%)Test Point Type














Below Class MinimumComments: Wall Thickness Class Minimum Calculated in accordance with the client class requirements. Legend:


APV´S Room Lv1 Design Pressure (psi): 207 Bar Qualification: SNT-TC-1A-UT- 3269

APV-48 Flow Sheet / Dr'g No: Inspector: Bruno Cerri

Page 31 of 32

Title:


1173 Line Number: N/A o e Molibednio ASTM A519 Gr

Ocean Rig Location: Mylos SFI Code: 315 Client WO: 2015-08331

INTEGRATE MANAGEMENT SYSTEM

RP-QT-116 Rev.02

RP-QT-134 Rev.1

Project:

Location:

DW N°:

Description:

To:From:

Date:


Rev.:1Scale: N/A

Legend

Point

Vacuum Degassers

WO N°:

Vacuum Dagassers VP-152

Mux Processor Room

DW-36

Mux Processor Room


02/10/2015

QT-1173

0

1

2

Portside

4

3

5

6

9

8

Foward

Tank Top Weldment Tank Bottom Weldment


AB

C

AB

CB

A

C

DDD

7

Mux Processor Room

11

Starboardside AFT

12

13

14

15

16

17

Foward19

18

Weld

10

RP-QT-134 Rev.1

Project:

Location:

DW N°:

Description:

To:From:

Date:


Rev.:1Scale: N/A

Legend

Point

Vacuum Degassers

WO N°:

Vacuum Dagassers VP-152

Mux Processor Room

DW-36

Mux Processor Room


02/10/2015

QT-1173

0

1

2

Portside

4

3

5

6

9

8

Foward

Tank Top Weldment Tank Bottom Weldment


AB

C

AB

CB

A

C

DDD

10

7

Mux Processor Room

11

Starboardside AFT

12

13

14

15

16

17

Foward

19

18

Weld

20


W.O. No: Steel Grade: Mat / Velocity: Cromo e Molibideno/5920m/s

Pipe Line:

Work Area:

N°Original

Thickness


(mm)

Test Point O.D

Actual W.T. (2015)


Actual W.T. (2016)


Actual W.T. (2017)



(mm)


(%)Test Point Type

1 8,5mm Low Pressure




















Below Class Minimum

Bruno Cerri

Comments: Wall Thickness Class Minimum Calculated in accordance with the client class requirements. Legend:


Design Pressure (psi): N/A Qualification: SNT-TC-1A-UT- 3269Mux Processor Room

Vacuum Degasers VP-152 Flow Sheet / Dr'g No: DW-036

INTEGRATE MANAGEMENT SYSTEM Page 1 of 1

Title:


Inspector:

N/A

Ocean Rig SFI Code: 326.300 Client WO: 2015-08317

1173 Line Number: ASTM A519 Gr 4130

Location: Mylos

RP-QT-116 Rev.02

Page 1 of 2



RP-QT-097B Rev.4

MAGNETIC PARTICLE INSPECTION REPORT

Client: Ocean Rig Location: Corcovado (NS-40) Report Number: MPI-1173-020

P.O. Nr: N/A Qualitech WO: 1173 Inspection Procedure: PI-QT-003 Rev.2

SFI Code: 334.911 Client WO: 2015-07476 Surface: Brushed

Equipment Description: Diverter Running Tool Qty: 1 Size: N/A

Serial Number: 20079432-02 Reference Drawing N°: N/A

Specification: ASTM E-709 Material: Carbon Steel Manufacture: NOV

Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Diverter Running Tool Result: No defects were found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Authorized for use. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:

Equipment/Magnetization

Magnetization Technique

Coil

Magnetization : Longitudinal Current Flow : Alternating

Ligth Type:

x Natural Artificial

x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “

Ilumination:1200 lux

Flux Indicator:

Berthold x Burmah Strip

Equipment Description: MY-2 Voltage: 110V Serial No:1303093

Test Method

Test Medium Dry X Colour Wet Wet Fluorescent

Particle Type: RW222

Contrast Type: 104

Antifoaming Type: 787


FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 2



RP-QT-097B Rev.4


Client: Petrobras Report Number: MPI-1173-020

P.O. Nr: N/A WO: 1173 Location: Corcovado (NS-40)

Item: Diverter Running Tool Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Diverter Running Tool


SNT/MT-3276

Signed/Stamp:


Approved By:

Page 1 of 2



RP-QT-097B Rev.4





Equipment Description: Frame Qty: 1 Size: 250 t

Serial Number: TF-01 Reference Drawing N°: N/A

Specification: ASTM E-709 Material: Carbon Steel Manufacture: N/A

Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Frame. Result: No defects were found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Authorized for use. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 2



RP-QT-097B Rev.4




Item: Frame Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Frame.


SNT/MT-3276

Signed/Stamp:


Approved By:

Page 1 of 2



RP-QT-104B Rev.2

EDDY CURRENT INSPECTION REPORT

Client: Ocean Rig Date: 07/10/15 Qualitech WO: Report Number: 2015-07648-EC-023

P.O. Nr: N/A Location: Corcovado Inspection Procedure: PI-QT-005 Rev.2

SFI Code: 335.321 Client WO: 2015-07648 Surface: Painted

Probes Probes Serial No Frequency Gain Phase Calibration

Absolute 501257/02 135-250 Khz 15 db 320 db Absolute

Bridge 503059/03 100 khz 40 db 72 db Bridge

NOTE: Compensations made for variable geometry and paint thickness.

Equipment Description: Spider

Serial Number: 20084370-1 Size: N/A

Manufacture: NOV Material: Carbon Steel Qty: 1

Specification: BSI BS-EN 1711 Reference Drawing N°: MPI-030

Comment: Area Inspected: As per clients request a Visual and Eddy Current Inspection was carried out on 100% of the accessible critical weld area of the Spider Result: No surface defects were found at time of inspection Conclusion: Acceptable to the Specification. Recommendations: Authorized for use Continuation Attached: Yes


SNT-ET 5373

Signed / Stamp:


Approved By:

Equipments

Page 2 of 2



RP-QT-104B Rev.2

EDDIE CURRENT INSPECTION REPORT

Client: Ocean Rig Report Number: 2015-07648-EC-023

P.O. Nr: N/A WO: 1173 Location: Corcovado

Item: Spider Inspection Details: As per clients request a Visual and Eddy Current Inspection was carried out on 100% of the accessible critical weld area of the Spider.


SNTC-ET 5373

Signed/Stamp:


Approved By:

Page 1 of 2



RP-QT-097B Rev.4





Equipment Description: Spider Qty: 1 Size: N/A



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Spider. Result: No defects were found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Authorized for use. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 2



RP-QT-097B Rev.4




Item: Spider Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Spider.


SNT/MT-3276

Signed/Stamp:


Approved By:

Page 1 of 2



RP-QT-097B Rev.4



P.O. Nr: Qualitech WO: 1173 Inspection Procedure: PI-QT-003 Rev.2

SFI Code: 335.935.005 Client WO: 2015-07650 Surface: Brushed

Equipment Description: Riser Running Tool Qty: 1 Size: N/A



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Riser Running Tool. Result: No defects were found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Authorized for use. Continuation Attached: Yes


Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 2



RP-QT-097B Rev.4

SNT/MT-3276




Item: Riser Running Tool Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Riser Running Tool.


SNT/MT-3276

Signed/Stamp:


Approved By:

Page 1 of 2



RP-QT-097B Rev.4


Client: Ocean Rig Location: Corcovado (NS-40) Report Number: MPI1173-023


SFI Code: 335.935.010 Client WO: 2015-07651 Surface: Brushed

Equipment Description: Riser Running Tool Qty: 1 Size: N/A



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Riser Running Tool. Result: No defects were found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Authorized for use. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 2



RP-QT-097B Rev.4




Item: Riser Running Tool Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Riser Running Tool.


SNT/MT-3276

Signed/Stamp:


Approved By:

Page 1 of 2



RP-QT-097B Rev.4





Equipment Description: Bails Qty: 2 Size: 750 t

Serial Number: 39L/39R Reference Drawing N°: N/A


Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Bails. Result: No defects were found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Authorized for use. Continuation Attached: Yes


ASNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 2



RP-QT-097B Rev.4




Item: Bails Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Bails.


ASNT/MT-3276

Signed/Stamp:


Approved By:

Page 1 of 8



RP-QT-097B Rev.4




SFI Code: 361-100 Client WO: 2014-50523 Surface: Brushed

Equipment Description: Knuckle Boom Crane #1 (Before Repair) Qty: 1 Size: 85t

Serial Number: V3454-2210 Reference Drawing N°: N/A


Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #1 (Before Repair) Result: Cracks were found at time of inspection. Conclusion: No Acceptable to the Specification. Recommendations: Repair following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 8



RP-QT-097B Rev.4




Item: Knuckle Boom Crane #1 (Before Repair) Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #1 (Before Repair) and Cracks were found at time.

Left Side

Right Side

Inspection before Repair


SNT/MT-3276

Signed/Stamp:


Approved By:

Page 3 of 8



RP-QT-097B Rev.4





Equipment Description: Knuckle Boom Crane #1 Qty: 1 Size: 85t



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #1. Result: Were no cracks found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Cracks removed following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 4 of 8



RP-QT-097B Rev.4




Item: Knuckle Boom Crane #1 Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #1.

Left Side

Right Side

Cracks removed after Inspection

Name & Qualification:

Bruno Cerri SNT/MT-3276

Signed/Stamp:


Approved By:

Page 5 of 8



RP-QT-097B Rev.4





Equipment Description: Knuckle Boom Crane #1 (After Repair) Qty: 1 Size: 85t



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #1 (After Repair). Result: Were no cracks found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Release for Use. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 6 of 8



RP-QT-097B Rev.4




Item: Knuckle Boom Crane #1 (After Repair) Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #1 (After Repair)

Left Side

Right Side

Inspection after Repair



Signed/Stamp:


Approved By:

Page 7 of 8



RP-QT-097B Rev.4





Equipment Description: Knuckle Boom Crane #1 (After Weld Plate) Qty: 1 Size: 85t



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #1 (After Weld Plate). Result: Were no cracks found at time of Inspection. Conclusion: Acceptable to the Specification. Recommendations: Release for Use. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 8 of 8



RP-QT-097B Rev.4




Item: Knuckle Boom Crane #1 (After Weld Plate) Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #1 (After Weld Plate)

Left Side

Right Side

Inspection after Weld Plate



Signed/Stamp:


Approved By:

Page 1 of 5



RP-QT-097B Rev.4








Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #2. Result: Cracks were found at time of inspection on Left Side. Conclusion: No Acceptable to the Specification. Recommendations: Repair following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 5



RP-QT-097B Rev.4




Item: Knuckle Boom Crane #2 Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #2 and Cracks were found at time of inspection.

Left Side

Looking AFT to FOWARD



Signed/Stamp:


Approved By:

Page 3 of 5



RP-QT-097B Rev.4



P.O. Nr: WO: 1173 Location: Corcovado (NS-40)

Item: Knuckle Boom Crane #2 Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #2.

Right Side




Signed/Stamp:


Approved By:

Page 4 of 5



RP-QT-097B Rev.4





Equipment Description: Knuckle Boom Crane #2 After Removed Crack

Qty: 1 Size: 85t



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #2. Result: No cracks were found at time of inspection and completed Removed. Conclusion: Acceptable to the Specification. Recommendations: Repaired following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 5 of 5



RP-QT-097B Rev.4




Item: Knuckle Boom Crane #2 Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #2 After Removed Crack

Removed all Crack

Left Side




Signed/Stamp:


Approved By:

Page 1 of 2



RP-QT-097B Rev.4








Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #3. Result: Cracks were found at time of inspection. Conclusion: No Acceptable to the Specification. Recommendations: Repair following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 2



RP-QT-097B Rev.4




Item: Knuckle Boom Crane #3 Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Boom Crane #3 and Cracks were found at time of inspection.

Left Side

Right Side

Looking Forward to AFT


SNT/MT-3276

Signed/Stamp:


Approved By:

Page 1 of 11



RP-QT-097B Rev.4





Equipment Description: Knuckle Weld Boom Crane #4 Qty: 1 Size: 85t



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4. Result: Cracks were found at time of inspection on Both Side. Conclusion: No Acceptable to the Specification. Recommendations: Repair following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 11



RP-QT-097B Rev.4


Client: Ocean Rig Report Number: MPI-1173-029


Item: Knuckle Weld Boom Crane #4 Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 and Cracks were found at time of inspection.

Right Side




Signed/Stamp:


Approved By:

Page 3 of 11



RP-QT-097B Rev.4




Item: Knuckle Weld Boom Crane #4 Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4, cracks were found at time of inspection

Left Side




Signed/Stamp:


Approved By:

Page 4 of 11



RP-QT-097B Rev.4





Equipment Description: Knuckle Weld Boom Crane #4 (After Removed Crack)

Qty: 1 Size: 85t



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 (After Removed Crack). Result: No defects were found at time of inspection. Conclusion: No Acceptable to the Specification. Recommendations: Repair following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 5 of 11



RP-QT-097B Rev.4




Item: Knuckle Weld Boom Crane #4 (After Removed Crack). Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 (After Removed Crack).

Right Side




Signed/Stamp:


Approved By:

Page 6 of 11



RP-QT-097B Rev.4




Item: Knuckle Weld Boom Crane #4 (After Removed Crack).Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 (After Removed Crack).

Left Side




Signed/Stamp:


Approved By:

Page 7 of 11



RP-QT-097B Rev.4





Equipment Description: Knuckle Weld Boom Crane #4 (After Re-Weld)

Qty: 1 Size: 85t



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 (After Re-Weld). Result: No defects were found at time of inspection. Conclusion: No Acceptable to the Specification. Recommendations: Repair following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 8 of 11



RP-QT-097B Rev.4




Item: Knuckle Weld Boom Crane #4 (After Re-Weld). Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 (After Re-Weld).

Right Side




Signed/Stamp:


Approved By:

Page 9 of 11



RP-QT-097B Rev.4





Equipment Description: Knuckle Weld Boom Crane #4 (Bracket Weld) Qty: 1 Size: 85t



Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 (Bracket Weld). Result: No defects were found at time of inspection. Conclusion: No Acceptable to the Specification. Recommendations: Repair following procedures NOV. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 10 of 11



RP-QT-097B Rev.4




Item: Knuckle Weld Boom Crane #4 (Bracket Weld) Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 (Bracket Weld)

Right Side




Signed/Stamp:


Approved By:

Page 11 of 11



RP-QT-097B Rev.4




Item: Knuckle Weld Boom Crane #4 (Bracket Weld) Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Knuckle Weld Boom Crane #4 (Bracket Weld)

Left Side




Signed/Stamp:


Approved By:

Page 1 of 1



RP-QT-072B Rev.2





SFI Code: N/A Client WO: N/A

Date of Examination: 06/10/2015 Manufacture: Crosby



Load

41259921 NVD- 3617 Safety Pin Bow Shackles Green Pin

Riser Deck 55 t N/A




Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 1 of 5



RP-QT-072B Rev.2






Date of Examination: 06/10/2015 Manufacture: Global Lifting Services



Load

W2-13-109/1 5 Leg Wire Rope Sling Soft Eye

1,14 mt x19 mm C/ 28mm Master Link Crosby CG81NV

Riser Deck 2,3 tonne N/A




Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 2 of 5



RP-QT-072B Rev.2









Load

W2-13-092/1 5 Leg wire rope sling Soft Eye

1,14 mt x 19mm C/ Master Link Crosby CG81NT





Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 3 of 5



RP-QT-072B Rev.2









Load







Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:

This certification or Report is granted or issued subject to the condition that it is understood and agreed upon that nothing herein shall be deemed to relieve any designer,manufacture, seller, supplier repairer, or operator of any warranty, express or implied and Qualitech. Liability shall be limited to the acs and omissions of it's employees, agents and subcontractors. Under no circumstances shall Qualitech be liable for any injury or damage to any person or property occurring by reason of negligent operation, misuse of or any defect in material, machinery, equipment, or other items other than defects in items actually inspected by Qualitech and ascertainable by normally accepted testing standards, or defects reflected in documents reviewed by Qualitech and which are covered by this certificate or report.The certificate or report and the recommendations contained in it are based upon the conditions and practices observed and information made available to Qualitech personnel. The report does not purport to list all hazards or faulty conditions not to indicate that other hazards or faulty conditions exist. Severety ratings in the report are based on the criteria shown in this report and are intended as a guideline only. No responsability is assumed for the control or correction of conditions

Page 4 of 5



RP-QT-072B Rev.2









Load







Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 5 of 5



RP-QT-072B Rev.2









Load







Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 1 of 6



RP-QT-072B Rev.2






Date of Examination: 06/10/2015 Manufacture: Crosby



Load

41259921 NVD- 3617 Safety Pin Bow Shackles Riser Deck 55 t N/A




Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 2 of 6



RP-QT-072B Rev.2






Date of Examination: 06/10/2015 Manufacture: Global Integrated Services



Load

190/1A-1D

4x Safety Pin Bow Shackles





Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 3 of 6



RP-QT-072B Rev.2









Load

188/1A-1D






Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 4 of 6



RP-QT-072B Rev.2









Load

148/1A-1D






Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 5 of 6



RP-QT-072B Rev.2









Load

213109/1A-1D






Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 6 of 6



RP-QT-072B Rev.2









Load

213092/1A-1D






Bruno Cerri

Signed / Stamp:

Date of Inspection:

06/10/2015

Approved by:


Page 1 of 7



RP-QT-097B Rev.4



P.O. Nr: Qualitech WO: 1173 Inspection Procedure: PI-QT-003 Rev.2

SFI Code: Client WO: Surface: Brushed

Equipment Description: Container (Pad Eye) Qty: 5 Size: 1110mm x 1110mm x2210mm

Serial Number: W2-13-109/W2-13-149/W2-13-188/W2-13-190/W2-13-92

Reference Drawing N°: JN 9150G

Specification: ASTM E-709 Material: Carbon Steel Manufacture: David Ritchie Equipment

Comment: Area Inspected: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Container (Pad Eye). Result: No defects were found at time of inspection. Conclusion: Acceptable to the Specification. Recommendations: Authorized for use. Continuation Attached: Yes


SNT/MT-3276

Signed / Stamp:


Approved By:



Coil


Ligth Type:


x Yoke Pull 10lbs

Yes Pole Spacing:

4” to 6 “


Flux Indicator:



Test Method



Contrast Type: 104



FL/Sample AT:

UV:0,1 to 0,4L

Visible:0,4 to 1,2L

Batch No:

Maker: Metal Check

Maker: Metal Check

Maker: Metal Check

Model: N/A

Batch Nr: 9884

Batch Nr: 7863

Batch Nr: 8733

Serial Nr: N/A

Page 2 of 7



RP-QT-097B Rev.4




Item: Container (Pad Eye) Inspection Details: As per clients request a Visual and Magnetic Particle Inspection was carried out on 100% of the accessible critical area of the Container (Pad Eye)


SNT/MT-3276

Signed/Stamp:


Approved By:

Page 3 of 7



RP-QT-097B Rev.4






SNT/MT-3276

Signed/Stamp:


Approved By:

Page 4 of 7



RP-QT-097B Rev.4






SNT/MT-3276

Signed/Stamp:


Approved By:

Page 5 of 7



RP-QT-097B Rev.4






SNT/MT-3276

Signed/Stamp:


Approved By:

Page 6 of 7



RP-QT-097B Rev.4






SNT/MT-3276

Signed/Stamp:


Approved By:

Page 7 of 7



RP-QT-097B Rev.4






SNT/MT-3276

Signed/Stamp:


Approved By:

Page 1 of 1

Qualitech Inspeção, Reparo e Manutenção Ltda. Estrada do Engenho D’Água,1330, Box01-C, Anil, Jacarepaguá–RJ – Brasil CEP 22765-240 www.qualitechirm.com

Quality for safety RP-QT-117B Rev.2

PHOTOGRAPHIC INSPECTION REPORT

Client: Ocean Rig WO: 1173 Report Number: PIR-1173-012

P.O. Nr: N/A Client PMS Number: N/A Location: Corcovado

Item: High Pressure Water

Details: Made Visual Inspection in the Pipe Leaking

Corrective Action: Was Changed Pipe


Signed / Stamp:


Approved by:

Sr. Allan Paulino Siqueira Mr. Allan Paulino Siqueira

Certificado Nº. ET - 4322 R1

Certificate Nr. ET - 4322 R1

É qualificado como Nível II no ensaio de Correntes Parasitas de acordo com os requisitos da Pratica Escrita da Qualitech PI QT 10 Rev.1 baseado na Prática Recomendada SNT-TC 1A (Ed. 2006) da ASNT.

Is qualified as Level II in Eddy Current testing according to the requirements of Qualitech

Written Practice PI QT 10 Rev. 1 based in recommended practice SNT-TC-1A (2006 edition) of ASNT.

Data da Certificação: 01 de Fevereiro 2013(IRM) Certification Date: Fevereiro 01st 2013 (IRM)

Recertificado em: Outubro de 2014 (R1) Recertificated in: October 2014 (R1)

Validade: Outubro de 2018 Validity: October 2018

Transferido para Qualitech em: Outubro de 2014

Transferred to Qualitech in: October 2014

_________________________ _________________________ Marco Antonio M. de Guido Leonardo Torres

Nível III ASNT nº. 85594 Qualitech Inspeção, Reparo e Manutenção Ltda.

Este certificado é válido por um período de cinco anos contados à partir da data acima, salvo cancelamento ou revogação em data anterior e perderá sua validade quando o nomeado deixar de ser funcionário da Qualitech Inspeção, Reparo e Manutenção Ltda.

This certificate is valid for a period of five years from the above date of signature, unless terminated or revoked at an earlier data, and it is automatically terminated when the above named ceases to be an employee of Qualitech Inspeção, Reparo e Manutenção Ltda.


Certificado Nº. MT - 3001 R1

Certificate Nr. MT - 3001 R1

É qualificado como Nível II no ensaio de Partículas Magnéticas de acordo com os requisitos da Pratica Escrita da Qualitech PI QT 10 Rev.1 baseado na Prática Recomendada SNT-TC 1A (Ed. 2006) da ASNT.

Is qualified as Level II in Magnetic Particle testing according to the requirements of Qualitech


Data da Certificação: 08 de Outubro 2010(IRM) Certification Date: October 08th 2010(IRM)


Validade: Outubro de 2016 Validity: October 2016








Certificado Nº. UT - 3267 ME

Certificate Nr. UT - 3267 R1 ME

É qualificado como Nível II no ensaio de Ultrasson / Medição de Espessura de acordo com os requisitos da Pratica Escrita da Qualitech PI QT 10 Rev.1 baseado na Prática Recomendada SNT-TC 1A (Ed. 2006) da ASNT.

Is qualified as Level II in Ultrasonic / Thickness Measure testing according to the requirements of Qualitech


Data da Certificação: 24 de Maio 2011(IRM) Certification Date: May 24th 2010(IRM)


Validade: Maio de 2016 Validity: May 2016







REGISTRO 36224/2015

Certificamos que Allan Paulino Siqueira participou do Treinamento deAtendimento a NR-34 Item 4 - Curso básico para Trabalhos a Quente -Módulo Geral - nas instalações da QUALITECH INSPEÇÃO, REPAROE MANUTENÇÃO LTDA, no dia 30 de Junho de 2015, carga horária08h.

___________________________Leonardo Torres Martins da SilvaDiretor de OperaçõesCNPJ:17.417.147/0001-84

__________________________________Antônio Carlos Dias PereiraCREA-RJ:1999105764CNPJ:10.848.080/0001-93

RP-QT-086 Rev.0

Rio de Janeiro, 30 de Junho de 2015.Validade: 12 meses

Estudo da NR-34, Item 34.5;b) Identificação de Perigos e Análise de Riscos• Conceitos de Perigos e Riscos;• Técnicas de Identificação de Perigos e Análise de Riscos;• APP e APR - Análise Preliminar de Perigos e Análise Preliminar de Riscos. c)Permissão para Trabalho - PT; d) Limite inferior e superior de explosividade; e) Medidas de Controle no Local de Trabalho • Inspeção Preliminar• Controle de materiais combustíveis e inflamáveis• Proteção Física• Atividades no entorno• Sinalização e Isolamento do Local de Trabalho;• Inspeção Posterior para controle de fontes de igniçãof) Renovação de Ar no Local de Trabalho (Ventilação/Exaustão);g) Rede de Gases (Válvulas e Engates); h) Ergonomia;i) Doenças ocupacionais;ii) j) FISPQ

RP-QT-066 Rev.0

Certificamos que Allan Paulino Siqueira participou do Treinamento deAtendimento a NR-34 Condições e Meio Ambiente de Trabalho naIndústria de Construção e Reparação Naval nas instalações daQUALITECH INSPEÇÃO, REPARO E MANUTENÇÃO LTDA, nodia 22 de setembro de 2015, carga horária 06h.



RP-QT-086 Rev.0

Rio de Janeiro, 22 de setembro de 2015.Validade: 12 meses

Riscos Inerentes as Atividades:− Divulgação dos Riscos Ocupacionais existentes em cada atividade e suas medidas de controle,Divulgação da Ordem de Serviço conforme NR-01.

Uso adequado de Equipamentos de Proteção Individual – EPI e Equipamento de Proteção ColetivaEPC existentes no estabelecimento:− Movimentação de Carga, equipamentos e acessórios, uso e operacionalidade.− Definição de EPI, Obrigatoriedades quanto ao uso dos mesmos conforme NR-06, Uso correto deEPI’s com exercício prático para Proteção de Cabeça, Tronco; Membros Inferiores e Superiores; Mãos;Pés; Olhos; Facial; Respiratória e Auditiva;− Guarda e higienização dos EPI´s;− Definição de EPC,Informações sobre os tipos de EPC´s existentes nas atividades da Empresa e emUnidades de Contratos e informações sobre o manuseio dos mesmos.

Condições e meio ambiente de trabalho:− Informações sobre Unidades de Contrato;− Regras de Segurança, Saúde e Meio Ambiente para as Atividades Operacionais;− Informações sobre sistemas para Identificação de Riscos e Reconhecimento de Boas Práticas de nossos clientes com exercício prático.

RP-QT-066 Rev.0

Sr. Bruno da Silveira Cerri Mr. Bruno da Silveira Cerri

Certificado Nº. MT - 3276

Certificate Nr. MT - 3276

É qualificado como Nível II no ensaio de Partículas Magnéticas de acordo com os requisitos da Pratica Escrita da Qualitech PI QT 10 Rev.0 baseado na Prática Recomendada SNT-TC 1A (Ed. 2006) da ASNT.

Is qualified as Level II in Magnetic Particle testing according to the requirements of Qualitech


Data da Certificação: 24 de Maio de 2011 (IRM) Certification Date: May 24th 2011 (IRM)

Validade: Julho de 2018 Validity: July 2018

Transferido para Qualitech em: Julho de 2014

Transferred to Qualitech in: Julho 2014





Sr. Bruno da Silveira Cerri Mr. Bruno da Silveira Cerri

Certificado Nº. UT - 3269

Certificate Nr. UT - 3269

É qualificado como Nível II no ensaio de Ultrassom / Medição de Espessura de acordo com os requisitos da Pratica Escrita da Qualitech PI QT 10 Rev.0 baseado na Prática Recomendada SNT-TC 1A (Ed. 2006) da ASNT.

Is qualified as Level II in Ultrasonic / Thickness Measure testing according to the requirements of Qualitech


Data da Certificação: 24 de Maio de 2011 (IRM) Certification Date: May 24th 2011 (IRM)

Validade: Maio de 2016 Validity: May 2016

Transferido para Qualitech em: Julho de 2014

Transferred to Qualitech in: Julho 2014





Certificamos que Bruno da Silveira Cerri participou do Treinamento deAtendimento a NR-34 Condições e Meio Ambiente de Trabalho naIndústria de Construção e Reparação Naval nas instalações daQUALITECH INSPEÇÃO, REPARO E MANUTENÇÃO LTDA, nodia 02 de Julho de 2015, carga horária 06h.



RP-QT-086 Rev.0

Rio de Janeiro, 02 de Julho de 2015.Validade: 12 meses




RP-QT-066 Rev.0

REGISTRO 40394/2015

Certificamos que Rennan Gaspar Mendes participou do Treinamentode Atendimento a NR-34 Condições e Meio Ambiente de Trabalho naIndústria de Construção e Reparação Naval nas instalações daQUALITECH INSPEÇÃO, REPARO E MANUTENÇÃO LTDA, nodia 27de Março de 2015, carga horária 06h.



RP-QT-086 Rev.0

Rio de Janeiro, 27 de Março de 2015.Validade: 12 meses




RP-QT-066 Rev.0

Documents

CLIENT: OCEANRIG VESSEL: CORCOVADO · section 01 – executive summary report section 02 – 196 – ccertificate of thorough examination – riser bridle section 03 – 313.331 –