Clarion Db178rmp Db179rmp

- 1 - DB178RMP/DB179RMP/DB179RGMP

(PE-2934E-B: For EUROPE)

Service ManualPublished by Clarion (Malaysia)298-6417-00 MAR. 2007PPrinted In Malaysia

Clarion ( Malaysia) Sdn. Bhd.Phase 3, Free Industrial Zone, 11900 Bayan Lepas, Penang, MalaysiaTel: (60) 4-6148-400, Fax: (60) 4-6439-108Clarion Co. Ltd.Export Division : 50 Kamitoda, Toda-shi, Saitama 335-8511 Japan

CD/MP3/WMA Receiver

Model

(PE-2934E-A: For EUROPE)Model

(PE-2935E-A: For EUROPE)Model

DB178RMP

WMASampling rate (kHz): 48, 44.1, 32Bit-rate (kbps): 32 - 192

Common in MP3/WMAFolder level limit: 8 levelMax. folder support: 128Max. files support: 254Logical format: ISO9660 Level 1, 2, Romeo or Joliet

GeneralMax. power output: 50W x 4Power output: 25Wx4 (DIN45324, +B=14.4V)Line output: 1.8V (with A/C 1kHz, 10k ohm)Bass control action: +14dB/-14dB (100Hz)Treble control action: +14dB/-14dB (10kHz)Power supply voltage: DC 14.4V (10.8 to 15.6V allowable) negative groundCurrent consumption: Less than 15ASpeaker impedance: 4 ohm (4 ohm to 8 ohm allowable)Dimensions (mm): 178 (W) x 50 (H) x 152 (D)Weight: 1.1kg

SPECIFICATIONSRadio sectionTuning system: PLL synthesizer tunerReceiving frequencies: FM 87.5 to 108MHz (0.05MHz steps) MW 531 to 1602kHz (9kHz steps) LW 153 to 279kHz (3kHz steps)

CD player sectionSystem: Compact disc audio systemUsable disc: Compact discFrequency response: 10Hz to 20kHz (+3dB/-3dB)Signal to noise ratio: 85dB (1kHz) IHF-ADynamic range: 87dB (1kHz)Harmonic distortion: 0.01%

MP3Decode format: MPEG 1, 2 and 2.5 - Layer 3Sampling rate (kHz): MPEG-1: 32, 44.1, 48 MPEG-2: 16, 22.05, 24 MPEG-2.5: 8, 11.025, 12Bit-rate (kbps): MPEG-1: 32 - 320 MPEG-2: 8 - 160 MPEG-2.5: 8 - 160 VBR

This product is a lead free model.Lead free solder is used in PWB stamped LF mark.Please keep the following conditions when you repair.

1. Use lead free solder. * Koki’s lead free solder S3X-55M 0.6mm (CLARION Parts No.642-0231-01) * Koki’s lead free solder S3X-55M 1.0mm (CLARION Parts No.642-0231-02) 2. Use a nitrogen solder system. 3. Do not use “General solder” and “Lead free solder” together.

LF

- 2 -DB178RMP/DB179RMP/DB179RGMP

To engineers in charge of repair or inspection of our products.Before repair or inspection, make sure to follow the instructions so that customers and engineers in charge of repair or inspection can avoid suffering any risk or injury.

1. Use specified parts. The system uses parts with special safety features against fire and voltage. Use only parts with equivalent characteristics when replacing them. The use of unspecified parts shall be regarded as remodeling for which we shall not be liable.The onus of product liability (PL) shall not be our responsibility in cases where an accident or failure is as a result of unspecified parts being used.2. Place the parts and wiring back in their original positions after replacement or re-wiring. For proper circuit construction, use of insulation tubes, bonding, gaps to PWB, etc., is involved. The wiring connection and routing to the PWB are specially planned using clamps to keep away from heated and high voltage parts. Ensure that they are placed back in their original positions after repair or inspection. If extended damage is caused due to negligence during repair, the legal responsibility shall be with the repairing company.

3. Check for safety after repair. Check that the screws, parts and wires are put back securely in their original position after repair. Ensure for safety reasons there is no possibility of secondary problems around the repaired spots. If extended damage is caused due to negligence of repair, the legal responsibility shall be with the repairing company.4. Caution in removal and making wiring connection to the parts for the automobile. Disconnect the battery terminal after turning the ignition key off. If wrong wiring connections are made with the battery connected, a short circuit and/or fire may occur. If extensive damage is caused due to negligence of repair, the legal responsibility shall be with the repairing company.5. Cautions in soldering Please do not spread liquid flux in soldering. Please do not wash the soldering point after soldering.6. Cautions in soldering for chip capacitors Please solder the chip capacitors after pre-heating for replacement because they are very weak to heat. Please do not heat the chip capacitors with a soldering iron directly.7. Cautions in handling for chip parts. Do not reuse removed chips even when no abnormality is observed in their appearance. Always replace them with new ones. (The chip parts include resistors, capacitors, diodes, transistors, etc.). Please make an operation test after replacement.8. Cautions in handling flexible PWB. Before working with a soldering iron, make sure that the iron tip temperature is around 270°C. Take care not to apply the iron tip repeatedly (more than three times) to the same patterns. Also take care not to apply the tip with force.9. Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.10. Cautions in checking that the optical pickup lights up. The laser is focused on the disc reflection surface through the lens of the optical pickup. When checking that the laser optical diode lights up, keep your eyes more than 30cms away from the lens. Prolonged viewing of the laser within 30cms may damage your eyesight.11. Cautions in handling the optical pickup The laser diode of the optical pickup can be damaged by electrostatic charge caused by your clothes and body. Make sure to avoid electrostatic charges on your clothes or body, or discharge static electricity before handling the optical pickup.11-1. Laser diode The laser diode terminals are shorted for transportation in order to prevent electrostatic damage. After replacement, open the shorted circuit. When removing the pickup from the mechanism, short the terminals by soldering them to prevent this damage.11-2. Actuator The actuator has a powerful magnetic circuit. If a magnetic material is put close to it. Its characteristics will change. Ensure that no foreign substances enter through the ventilation slots in the cover.11-3. Cleaning the lens Dust on the optical lens affects performance. To clean the lens, apply a small amount of isopropyl alcohol to lens paper and wipe the lens gently.

1. Source unit 12. DCP case 335-5734-26 1 3. Mounting bracket 300-7742-20 14. Outer-escutcheon 371-5876-00 15. Parts bag 15-1. Removal key 331-2497-20 25-2. Stopper 335-4899-20 15-3. Screw 716-0726-51 15-4. Spacer 345-3653-01 15-5. A-Lead 850-6681-50 1

COMPONENTS

NOTES* Use only compact discs bearing the mark. * Some CDs recorded in CD-R/CD-RW mode may not be usable.* This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from MSLGP.* Windows Media™ and Windows® logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. * We cannot supply PWB with component parts in principle. When a circuit on PWB has failure, please repair it by component parts base. Parts which are not mentioned in service manual are not supplied.* Specifications and design are subject to change without notice for further improvement.


CAUTIONSThis appliance contains a laser system and is classified as a“CLASS 1 LASER PRODUCT”. In case of any trouble with thisplayer, please contact your nearest “authorized service station”.To prevent direct exposure to the laser beam, do not try to openthe enclosure.

Bottom view of main unit

PE-2934E-B

NOTES OF ISO CONNECTOR1. For VW amd Audi vehicles, change the position of fuse installation as shown on the diagram. (Figure 1)

2. When the car stereo is installed in 1998 and later Volkswagen models, make sure to cut the car lead wire connected the A-5 terminal. (A breakdown could occur if the lead wire is not cut.) After cutting the lead wire, insulate the front end of the lead wire with insulation tape tp prevent the risk of short-circuits. (Figure 2) Note: Before cutting the lead wire, disconnect the car battery - (negative) cable.3. When the Main Unit is also connected to an external amplifier, connect REMOTE on the external amplifier to the previously cut lead wire on the side of the connector.

The position of fuse for other vehicles.

The position of fuse for VW and Audi vehicles.

ISO CONNECTOR type

Main unit sideISO connector

Figuer 1

Figuer 2

ADJUSTMENTItem Procedure Measuring Instrument

S-Meter 1. Input the 98.1MHz/30dBu/400Hz (Main 90% + Pilot 10%) signal.2. Turn on the power switch and press the AF button and CH4 button at the same time for about 2 seconds. (Test Mode)3. Adjust the reading of LCD indicator to [24----00] 2.4 + 0.1V / - 0.1V by VR101.

SG


TROUBLESHOOTING

Write MP3/WMA files onto the disc properly.

Use MP3/WMA files encoded properly.

Use ISO9660 level 1, 2 or JOLIET or Romeo file system.

Clean the disc with a soft cloth.

Replace with a disc with no scratches.

Use MP3/WMA files encoded properly.

Let dry for about 1 hour with the power on.

Use ISO9660 level 1, 2 or JOLIET or Romeo file system.

No sound heard.

Sound skips or is noisy.

Sound is cut or skipped.Noise is generated ornoise is mixed with sound.Sound is bad directly after power is turned on.

Wrong file name

Problem Cause Measure

MP3/WMA files are absent in a disc.

Files are not recognized as an MP3/WMA file.

File system is not correct.

Disc is dirty.

Disc is heavily scratched or warped.

MP3/WMA files are notencoded properly.

Water droplets may form on the internal lens when the car is parked in a humid place.

File system is not correct.

CD

/MP3

/WM

AProblem Cause Measure

Power antenna lead is shorted to ground or excessive current is required for remote-on the amplifiers or power antenna.

Gen

eral

Power does not turn on. (No sound is produced)

Fuse is blown. Replace with a fuse of the same amperage.

Incorrect wiring. Read the attached “Installation/Wire connection Guide”once again and wire properly.

No sound output when operating the unit with amplifiers or power antenna attached.

1. Turn the unit off.2. Remove all wires attached to the power antenna lead.

Check each wire for a possible short to ground using an ohm meter.

3. Turn the unit back on.4. Reconnect each amplifier remote wire to the power

antenna lead one by one. If the amplifiers turn off before all wires are attached, use an external relay to provide remote-on voltage (excessive current required).

Nothing happens when button are pressed.Display is not accurate.

The microprocessor has malfunctioned due to noise, etc.

Turn off the power, then press the [RELEASE] button and remove the DCP.Press the reset button for about 2 seconds with a thin rod.

DCP or main unit connectors are dirty.

Wipe the dirt off with a soft cloth moistened with cleaning alcohol.

No sound heard. The speaker protection circuitis operating.

Turn down sound volume. Function can also be restored by turning the power off and on again. (Speaker volume is reduced automatically when the speaker protection circuit operates).

ERROR DISPLAYS

This is a failure of CD deck’s mechanism andconsult your store of purchase.

Replace with a non-scratched, non-warped-disc.

Eject the disc then reload it properly.

Error display Cause Measure

A DISC is caught inside the CD deck and is not ejected.

A DISC cannot be played due to scratches,etc.

A DISC is loaded upside-down inside the CD deck and does not play.

CD

/MP3

/WM

A ERROR 2

ERROR 3

ERROR 6


BLOCK DIAGRAMMain/Switch section


1 B/U DET I B/U detection input (L: Power failing, H: Normal) 2 P-CTRL O Power regulator control 0~1V = Power off 4~5V= Power on (ACC5V, AUDIO9V , ILM, EXT, CD8V) 3 EXTAMP_ON O External amp control (L: Power off, H: Power on) 4 EVOL_SDA O E-VOL control data output 5 EVOL_SCL O E-VOL control clock output 6 DIAGNOSTICS I While protecting circuit state, it is at ‘L’ (L: Abnormal, H: Normal) 7 PROGRAM O While software programming, it is at ‘H’ (L: Normal H: Programming) 8 AMP_STBY O Power amp control output (L: Standby, H: Operation) 9 NC O Connect to GND 10 RESET I System reset input (L: Reset, H: Normal) Caution: No need connect to VDD 11 PHONE_INT I Phone detection input (L: Phone, H: Normal) 12 ILL_DET I Illumination detect (L: On, H: Off) 13 FLMD0 - Flash memory programming port. Jumper to EVSS or VSS in normal operation mode. 14 X_OUT - Crystal 12MHz (Main system clock). Connect to flash programmer CLK line in programming mode. 15 X_IN I Crystal 12MHz (Main system clock). 16 REGC - Regulator capacitance. Connect to GND via capacitor 0.47uF or 1uF 17 VSS - Connect to GND 18 EVSS - Connect to GND 19 VDD - 5V power supply 20 EVDD - 5V power supply 21 MP3_SCL O MP3 serial/12C clock* 22 MP3_SDA I/O MP3 serial/12C data* 23 SYS_MUTE O Audio mute control output (L: Mute on, H: Mute off) 24 MP3_SRAM O MP3 decoder SRAM Standby output (L: Operation, H: Standby) 25 REMOCON I Remote control 26 CD_REM O CD/MP3 power supply control output (L: Off, H: On) 27 MP3_REM O MP3 power supply control output (L: Off, H: On) 28 MP3_REQ I REQ from MP3 decoder

EXPLANATION OF IC

uPD78F0547GK-8EU-A 052-3971-30 Master micro computer

PIN No. PIN NAME I/O DESCRIPTION

Outward form

80 pins, plastic QFP

Terminal description

PIN No. PIN NAME I/O DESCRIPTION (L: Request) 29 MP3_RESET O Reset MP3 decoder (L: Reset H: Operation) 30 CD_RESET O GS-I CD servo reset output (L: Reset, H: Operation) 31 CD_CCE O GS-I CD servo chip enable output 32 CD_BUCK O GS-I CD servo control clock output 33 CD_BUS3 I/O GS-I CD servo data communication port 34 CD_BUS2 I/O GS-I CD servo data communication port 35 CD_BUS1 I/O GS-I CD servo data communication port 36 CD_BUS0 I/O GS-I CD servo data communication port 37 ZDET I GS-I CD DAC zero data detection input (H: Zero data) 38 LD_MUTE O GS-I CD loading mute control (L: Play, H: Load/eject) 39 LD_CONT O GS-I CD loading/eject control output (L: Loading, H: Eject) 40 CD_SBSY I GS-I CD sub-code block sync detection input 41 ACC DET I ACC detection input (L: Off, H: On) 42 S-STOP I GS-I CD pick-up inner limit detection input (L: Limit, H: Playable) 43 CHU-SW I GS-I CD disc chucking detection input (L: Completed, H: Uncompleted) 44 TR-B I GS-I CD disc detection input (L: No disc, H: inserted) 45 TR-A I GS-I CD eject detection input (L: Eject, H: Disc-in) 46 KEY_INT I Key detection input interrupt 47 PWM-R O Key iIIumination red 48 PWM-G O Key iIIumination green 49 PWM-B O Key iIIumination blue 50 FL_RX I Flash memory programming port. Jumper to EVSS or VSS in normal operation mode. 51 FL_TX I Flash memory programming port. Jumper to EVSS or VSS in normal operation mode. 52 LCD_DO O LCD data output 53 LCD_DI I LCD data input 54 LCD_CLK O LCD clock output 55 LCD_CE O LCD chip enable output 56 VOL-CW I Rotary volume pulse input 57 VOL-CCW I Rotary volume pulse input 58 DISP_REM O DCP power supply control output (L: Off, H: On)


70 RDS_DATA O RDS Data Input 71 RDS_MUTE O FM Audio Mute Output (L: Mute Off H: Mute On) 72 MUTE_SPEED O FM SD Response Control Output (L: Fast H: Normal) 73 SD/ST_IND I AM/FM SD and stereo detection signal input (L: SD On/stereo, H: SD Off/mono) 74 ST O FM SD mode Control Output (L: IF signal Inhibit H: IF signal Request) 75 PLL_CE O PLL chip enable output 76 PLL_DO O PLL control data output 77 PLL_DI I PLL data input 78 PLL_CLK O PLL control clock output 79 RDS_CLK O RDS Clock Input 80 TBASE I PLL time base signal (8Hz) input

59 AVREF - ADC reference voltage input. Caution: voltage must be lower than 6.5V 60 AVSS - Analog GND Caution: -0.5 to +0.3V 61 KEY_A/D I FUNC/EJECT/DCP detection input 62 M-TEST I Test mode input (L: Test, H: Normal) 63 RDS_NOISE I FM Noise Detection Signal Input 64 RDS_SMETER I FM Signal Level Meter Input 65 NC O Connect to GND 66 CD_CHECK O H: CD loading & disc chucking & Disc accessing, L: Other status 67 AREA1 I Destination selection input 68 AREA2 I Destination selection input 69 RDS_DISCHG O FM Noise Detection Reset Output (L: Operation H: Reset)

PIN No. PIN NAME I/O DESCRIPTION PIN No. PIN NAME I/O DESCRIPTION

DESTINATION TABLEAREA1 (Pin 67)

LAREA2 (Pin 68)

LDestination

Europe

SD/ST_IND (PIN 73) FUNCTION SELECTION TABLEPin 9 of LC72146M

LLH

SD/ST IND (Pin 73)ST/mono input (AM receiving)

ST/mono input without IF countST/mono input with IF count (Seek)

ST (Pin 74)LHH



TC94A15FG 051-6399-00 CD mechanism IC

Outward form


Terminal description PIN No. PIN NAME I/O DESCRIPTION

1 IPF O IP flag output 2 SBOK O Sub code Q data CRCC OK signal output 3 CLCK I/O The clock pulse input/output for the sub code reading 4 VDD3 - Positive supply voltage 5 VSS3 - Negative supply voltage 6 DATA O DATA 7 SFSY O Playback frame synchronous signal output 8 SBSY O Sub code block sychronous signal output 9 HSO O The play speed flag ouput 10 UHSO O The play speed flag output 11 ARSEL I Fix to the high level 12 AWRC O The control signal ouput for the active wide range VCO 13 PVDD3 - PLL positive supply voltage. 14 PDO O Phase difference signal output of EFMPLCK. 15 TMAXS O T max judgment output. 16 TMAX O T max judgment output. 17 LPFN I Inverted input of LPF for PLL. 18 LPFO O The output terminal for the Low Pass Filter. 19 PVREF - PLL reference voltage. 20 VCOF O Loop filter for VCO. 21 VCOREF I VCO reference voltage input. 22 DTCN O For the analog slicer. 23 DTCP O For the analog slicer. 24 PVSS3 - PLL ground. 25 SLCO O Output of internal DAC for data slice level generation. 26 RFI I RF signal input. 27 RFRPI I RF ripple input. 28 RFEQO O The output of the RF equalizer. 29 A VDD3 - Positive supply voltage for the Analog section. 30 RESIN - For reference current setting. 31 VRO O The reference voltage output. 32 VMDIR O The reference voltage output. 33 TESTR O The compensation terminal for RFEQO offset. 34 INVSEL I MDI polarity selection. 35 AGCI I The input terminal of RF AGC amplifier. 36 RFDCI I The input terminal for RF peak detection. 37 RFO O RF signal output. 38 PNSEL I The transistor type selection input for laser diode driver. L=NPN, H=PNP.

39 EQSET O The equalizer setting terminal. 40 RVDD3 - RF power supply. 41 LDO O The laser diode drive output. 42 MDI I Monitor photo diode signal input. 43 RVSS3 - RF ground. 44 FNI2 I Main beam signal input. 45 FNI1 I Main beam signal input. 46 FPI2 I Main beam signal input. 47 FPI1 I Main beam signal input. 48 TPI I Sub beam signal input. 49 TNI I Sub beam signal input. 50 FTE O For test. 51 RFZI I RF ripple zero cross signal input. 52 AVSS3 - Analog ground. 53 RFRP O RF ripple signal output. 54 RFDC O RF peak detection signal output. (hologram suitable) 55 FEI O Focus error signal output. 56 SBAD O Sub beam add signal output. 57 TEI O Tracking error signal output. 58 TEZI I Tracking error signal input for zero cross. 59 AVDD3 - Positive supply voltage for the Analog section. 60 FOO O Focus equalizer output. 61 TRO O Tracking equalizer output. 62 VREF O Reference voltage output. 63 FMO O Field equalizer output/speed error output. 64 DMO O Disk equalizer output. 65 IO2A I/O General input/output. 66 IO3A I/O General input/output. 67 MONIT O Internal DSP signal monitor. 68 FGIN I FG input for the spindle CAV servo. 69 VSS3 - Negative supply voltage. 70 VDD3 - Positive supply voltage. 71 TESIN I For test. 72 XVSS3 - Master clock analog ground. 73 XI I Crystal connection. 74 XO O Crystal connection. 75 XVDD - Clock power supply. 76 DVSS3 - Digital ground. 77 RO O Right channel data output for 1-bit DAC. 78 DVDD3 - Positive supply voltage for the digital section. 79 DVR O Digital reference voltage. 80 LO O Left channel data output for 1-bit DAC. 81 DVSS3 - Digital ground. 82 ZDET O 1bit DAC zero flag output.


PIN No. PIN NAME I/O DESCRIPTION 31 Pio7 I/O NC 32 SDo1 O NC 33 SDo2 O NC 34 Po12 O NC 35 SDo3 O NC 36 REQ O Request pin for interrupt host 37 Po10 O NC 38 Po9 O NC 39 Po8 O NC 40 VDDM - VDD 1.5V 41 SRMSTBY I Internal 1MBitSRAM standby pin (H: STBY, L: Normal) 42 VDDT - VDD 3.3V 43 AD10 O NC 44 AD9 O NC 45 AD8 O NC 46 Po7 O NC 47 Po6 O NC 48 Po5 O NC 49 Po4 O NC 50 Po3 O NC 51 Po2 O NC 52 Po1 O NC 53 Po0 O NC 54 VSS - GND 55 VDD - VDD 1.5V 56 CKo/AD16/Po13 O NC 57 VDDX - VDD 1.5V 58 Xo O 16.9344MHz X-TAL output pin 59 Xi I 16.9344MHz X-TAL input pin 60 VSSX - GND 61 TEST I GND 62 MiMD I Communication mode select (H: 12C, L: Serial) 63 VSSP - GND 64 VCOi O Controlled voltage input for VCO circuit

TC94A34FG 051-6711-10 MP3 decoder IC

1 VDDP - VDD 1.5V 2 /RESET I Reset Port 3 STANDBY I Standby terminal (H: STBY; L: Normal) always connect to GND 4 /MiCS I NC 5 /MiLP I NC 6 MiDiO I/O Data input/output for micom interface (12C: SDA) 7 /MiCK I Clock input for Micom interface (12C: SCL) 8 MiACK O NC 9 VDDT - VDD 3.3V 10 VSS - DGND 11 SDo0 O Data output for Audio Interface 12 BCKo O NC 13 LRCKo O NC 14 SDi0 I Data Input-0 for Audio Interface 15 BCKiA I Bit Clock input-A for audio interface 16 LRCKiA I LR clock input-A for audio interface 17 SDi1 I Connect to GND 18 BCKiB I Bit Clock input-B for audio interface. Short to Pin 15 19 LRCKiB I LR clock input-B for audio interface. Short to Pin 16 20 TXo O NC 21 VDD - VDD 1.5V 22 CKi/iRQ/Fi0 I/O GND 23 VSS - DGND 24 Pio0 I/O NC 25 Pio1 I/O NC 26 Pio2 I/O NC 27 Pio3 I/O NC 28 Pio4 I/O NC 29 Pio5 I/O NC 30 Pio6 I/O NC

PIN No. PIN NAME I/O DESCRIPTION PIN No. PIN NAME I/O DESCRIPTION


Outward form


Terminal description

83 VSS5 - Negative supply voltage. 84 BUS0 I/O CD IC Data input/output. 85 BUS1 I/O CD IC Data input/output. 86 BUS2 I/O CD IC Data input/output. 87 BUS3 I/O CD IC Data input/output. 88 BUCK I CD IC Data clock input. 89 /CCE I Chip enable input. 90 /RST I Reset signal input. 91 VDD5 - Positive supply voltage. 92 EMPHI/FAO I/O Emphasis input for 1-bit DAC/ Flag A output. 93 BCKI/FBO I/O Bit clock input for 1-bit DAC/Flag B output.

94 AIN/FCO I/O Audio input for 1-bit DAC/Flag C output. 95 LRCKI/FDO I/O LR clock input for 1-bit DAC/ Flag D output. 96 EMPH O Emphasis flag output. H=Emphasis ON. 97 BCK O Bit clock output. 98 AOUT O Audio signal output. 99 LRCK O LR clock output. 100 DOUT O Serial data output.


EXPLODED VIEW • PART LISTDCP section

1 DCP-601-700 DCP-ASSY (PE-2934E-A) 1 DCP-602-700 DCP-ASSY (PE-2934E-B) 1 DCP-604-700 DCP-ASSY (PE-2935E-A) 1 1-1 750-6849-00 SPRING 1 1-2 947-0694-00 ESC-SUB-ASSY(PE-2934E-A) 1 947-0694-04 ESC-SUB-ASSY(PE-2934E-B) 1 947-0694-02 ESC-SUB-ASSY(PE-2935E-A) 1 1-3 382-8334-00 BUTTON PLAY 1 1-4 382-8336-00 BUTTON S/TA/RE 1 1-5 382-8337-00 BUTTON EJECT/D 1 1-6 382-8340-00 BUTTON 2/SRC 1 1-7 382-8339-00 BUTTON 1/3 1 1-8 382-8342-00 BUTTON 5/BND 1 1-9 382-8341-00 BUTTON 4/6 1 1-10 382-8335-00 BUTTON FOR 1 1-11 335-8087-00 ILLUMI PLATE 1 1-12 345-6034-00 RUBBER KEYPAD 1

No. PART No. DESCRIPTION Q’TY No. PART No. DESCRIPTION Q’TY 1-13 335-8086-00 REAR COVER 1 1-14 716-0872-61 SP SCREW (M1.7x6) 5 1-15 380-5702-00 KNOB 1 1-16 016-9901-02 VR SWITCH 1 1-17 331-4409-00 LCD COVER 1 1-18 335-8109-00 LCD HOLDER 1 1-19 379-5018-00 LCD 1 1-20 347-8200-00 FILM 1 1-21 347-8199-00 SHADE 1 1-22 335-8088-00 LCD ILLUMI 1 1-23 345-6035-00 ZEBRA CONNECTOR 1 1-24 ----------------- SWITCH PWB 1 1-25 001-7824-90 DIODE (PE-2934E-A) 5 001-7820-90 DIODE (PE-2934E-B) 5 001-7816-90 DIODE (PE-2935E-A) 5 1-26 076-0703-12 PLUG 1

Note:- Several different parts of the same reference number are alternative parts. One of those parts is used in the set.


Main section

1 714-2606-8H MC SCREW (M2.6x6) 2 2 346-0097-00 LEATHER SHEET 1 3 382-8120-00 BUTTON PICK-UP 1 4 750-6823-00 BTN P-UP SPRING 1 5 370-6288-00 INNER ESCUTCHEON 1 6 335-5915-20 HOOK 1 7 750-6824-00 HOOK SPRING 1 8 341-1627-20 SHAFT 1 9 816-4006-60 FLAT WIRE 1 10 731-3005-8B TAP TIGHT (M3x5) 4 11 714-2604-8B MC SCREW (M2.6x4) 3 12 331-3607-02 MECH BRKT 2 13 929-5011-80 CD MECHA MODULE 1 14 331-3366-02 MECH BRKT 1 15 310-1775-13 UPPER CASE 1 16 276-0170-00 SETPLATE (PE-2934E-A) 1 276-0250-00 SETPLATE (PE-2934E-B) 1 276-0202-00 SETPLATE (PE-2935E-A) 1 17 311-1848-03 LOWER CASE 1 18 880-2093U TUNER 1 19 854-4611-60 EXTENSION LEAD 1 20 075-9015-00 JACK 1 21 013-3932-01 TACT SWITCH 1 22 074-1143-15 FPC CONNECTOR 1

23 331-3630-00 CONNECTOR COVER 1 24 074-1316-12 OUTLET SOCKET 1 25 ----------------- MAIN PWB 1 26 074-1138-60 FFC-CONNECTOR 1 27 335-7501-01 FPC PROTECTOR 1 28 009-9006-60 CHOKE 1 29 331-3996-00 IC-HOLDER 1 30 092-4000-51 ANT RECEPT 1 31 331-1861-21 EARTH PLATE 1 32 051-3349-00 IC 1 33 051-2060-00 IC 1 34 042-1545-00 E-CAP 1 35 060-0057-57 AUTO-FUSE (15A) 1 36 074-1285-00 OUTLET SOCKET 1 37 ----------------- ISO PWB 1 38 313-2014-00 HEATSINK 1 39 855-5516-60 RCA PIN CORD 1 40 855-0593-00 EXTENSION LEAD 1 41 731-3008-8B TAP TIGHT (M3x8) 4 42 731-3012-8B TAP TIGHT (M3x12) 3 43 714-3006-8B MC SCREW (M3x6) 2 44 335-0833-01 LEAD HOLDER 1 45 331-2744-00 STOPPER 1

No. PART No. DESCRIPTION Q’TY No. PART No. DESCRIPTION Q’TY


EXPLODED VIEW • PARTS LISTCD mechanism section 929-5011-80


No. PART No. DESCRIPTION Q’TY 1 ------------------ SENSOR PWB 1 2 966-1743-21 DRIVE-PLT-ASSY 1 3 SMA-182-100 SPINDLE MOTOR-ASSY 1 4 SMA-183-100 SLED MOTOR-ASSY 1 5 345-5476-20 CUSHION RUBBER 1 6 620-1023-23 CLAMPER PLATE 1 7 620-1026-21 SPRING PLATE 1 8 620-1596-23 CLAMPER LINK 1 9 620-1598-22 UPPER CHASSIS 1 10 620-1752-20 SENSOR ARM 1 11 620-1753-20 ID-LOCK PLATE 1 12 620-1748-21 LOWER CHASSIS 1 13 621-0608-21 SECOND GEAR 1 14 621-0609-20 BASE GEAR 1 15 621-0610-20 IDLE GEAR A 1 16 621-0611-20 IDLE GEAR B 1 17 621-0612-21 ROLLER GEAR A 1 18 621-0620-20 THREAD GEAR A 1 19 621-0621-20 THREAD GEAR B 1 20 621-0623-23 LS-HOLDER 1 21 621-0624-22 GUIDE RAIL 1 22 621-0711-20 LOADING ROLLER 2 23 621-0718-21 ROLLER GUIDE 1 24 621-0719-20 ROLLER GEAR 1 25 621-0720-20 ROLLER GEAR C 1 26 621-0721-20 ROLLER GEAR D 1 27 621-0728-20 STOPPER LINK 1 28 621-1719-20 IDLE CASE 1 29 621-1726-20 ROLLER SLEEVE 2 30 621-1729-20 SH-BASE 1 31 621-1742-20 UPPER GUIDE 1 32 621-1743-20 SHIFT LEVER 1 33 621-1744-20 RACK 1 34 621-1745-20 LOCK ARM L 1 35 621-1746-20 LOCK ARM R 1 36 621-1747-20 GEAR COVER 1 37 621-1748-20 POWER GEAR A 1

No. PART No. DESCRIPTION Q’TY 38 621-1749-20 POWER GEAR B 1 39 621-1750-20 POWER GEAR C 1 40 621-1751-20 POWER GEAR D 1 41 621-1752-20 DISC STOPPER 1 42 621-1753-20 CLAMPER RING 1 43 621-1754-20 GEAR BASE 1 44 622-1571-21 ROLLER SHAFT 1 45 624-0020-00 LEAD SCREW 1 46 629-0086-20 DAMPER F 2 47 629-0087-20 DAMPER R 1 48 716-1507-01 SCREW (M2x3) 1 49 716-1670-01 SCREW (M2x4) 4 50 716-1733-01 SCREW (M1.7x2.3) 2 51 716-3469-01 SCREW (1.7x4) 2 52 716-3473-01 SCREW (M2X3) 1 53 716-3551-00 SCREW (M1.4X2.5) 2 54 750-3467-21 SHIFT SPRING 1 55 750-3468-20 RACK SPRING 1 56 750-3469-20 CLAMPER SPRING 1 57 750-3470-20 ID-LOCK SPRING 1 58 750-3471-20 SENSOR SPRING 1 59 750-3472-21 DR-SPRING F 2 60 750-3473-20 DR-SPRING RA 1 61 750-3474-20 DR-SPRING RB 1 62 750-3475-21 DR-SPRING C 1 63 750-6797-20 ROLLER SPRING L 1 64 750-6798-20 ROLLER SPRING R 1 65 780-2003-01 SCREW (M2x3) 2 66 780-2025-00 SCREW (M2x2.5) 3 67 781-1730-00 SCREW (M1.7x3) 1 68 803-4906-60 VINYL-COAT-WIRE (ORG) 1 69 969-0071-32 PICKUP-ASSY 1 70 816-2590-00 SPECIAL LEAD (GRN) 1 71 816-2591-00 SPECIAL LEAD (YEL) 1 72 816-2592-00 SPECIAL LEAD (BLUE) 1 73 816-2593-00 SPECIAL LEAD (PUR) 1 74 966-1722-20 SH-RACK-ASSY 1


REF No. PART No. DESCRIPTION

ELECTRICAL PARTS LISTMain PWB (B1) section

ANT101 092-4000-51 ANT-RECEPTBL101 880-2093U TUNERC101 166-2201-50 50V 22pFC102 166-2201-50 50V 22pFC103 168-1032-55 50V 0.01uFC104 168-1032-55 50V 1000pFC105 168-1022-55 50V 0.01uFC106 187-1073-25 10V 100uFC107 168-1042-78 50V 0.1uFC108 168-1032-55 50V 0.01uFC109 187-4763-35 16V 47uFC110 187-1073-25 10V 100uFC111 168-1032-55 50V 0.01uFC112 168-6822-55 50V 6800pFC113 168-1532-55 50V 0.015uFC114 168-1532-55 50V 0.015uFC115 168-1022-55 50V 1000pFC116 168-4732-78 50V 0.047uFC117 187-1053-65 50V 1uFC118 168-1232-55 50V 0.012uFC119 168-1032-55 50V 0.01uFC120 187-4753-65 50V 4.7uFC123 168-1022-55 50V 1000pFC127 187-4763-35 16V 47uFC128 168-1042-78 50V 0.1uFC132 168-2232-55 50V 0.022uFC202 168-1042-78 50V 0.1uFC203 168-1042-78 50V 0.1uFC204 168-1042-78 50V 0.1uFC205 042-1598-90 10V 470uFC208 178-4742-78 25V 0.47uFC209 168-2232-55 50V 0.022uFC211 166-1011-50 50V 100pFC301 187-1063-35 16V 10uFC302 166-3311-50 50V 330pFC303 166-5611-50 50V 560pFC304 166-4701-50 50V 47pFC305 166-5601-50 50V 56pFC306 168-1042-78 50V 0.1uFC307 187-4763-15 6.3V 47uFC308 168-2232-55 50V 0.022uFC309 168-1032-55 50V 0.01uFC310 168-2232-55 50V 0.022uFC311 166-1007-50 50V 10pFC312 166-8211-50 50V 820pFC313 166-6811-50 50V 680pFC315 168-1042-78 50V 0.1uFC401 168-3322-55 50V 3300pFC402 168-1522-55 50V 1500pFC403 187-1063-35 16V 10uFC404 187-1053-65 50V 1uFC405 168-1042-78 50V 0.1uFC406 187-4753-65 16V 10uFC408 168-4722-55 50V 4.7uFC409 168-1042-78 50V 0.1uFC410 178-4742-78 25V 0.47uF

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTIONC411 187-1053-65 50V 1uFC414 168-1042-78 50V 0.1uFC415 168-1042-78 50V 0.1uFC416 168-1522-55 50V 1500pFC417 168-3322-55 50V 3300pFC418 187-1053-65 50V 1uFC419 168-1042-78 50V 0.1uFC420 187-4753-65 50V 4.7uFC422 168-4722-55 50V 4700pFC423 168-1042-78 50V 0.1uFC424 178-4742-78 25V 0.47uFC425 187-1053-65 50V 1uFC428 168-1042-78 50V 0.1uFC501 187-1053-65 50V 1uFC502 178-2242-78 50V 0.22uFC503 178-2242-78 50V 0.22uFC504 168-4732-78 50V 0.047uFC505 178-2242-78 50V 0.22uFC506 178-2242-78 50V 0.22uFC507 168-1042-78 50V 0.1uFC508 187-1053-65 50V 1uFC509 166-1011-50 50V 100pFC510 166-1011-50 50V 100pFC516 187-1073-25 10V 100uFC601 178-4742-78 25V 0.47uFC602 178-4742-78 25V 0.47uFC603 178-4742-78 25V 0.47uFC604 178-4742-78 25V 0.47uFC605 166-1011-50 50V 100pFC606 166-1011-50 50V 100pFC607 166-1011-50 50V 100pFC608 166-1011-50 50V 100pFC609 187-1063-35 16V 10uFC610 187-1063-35 16V 10uFC613 168-4722-55 50V 4700pFC614 187-1063-35 16V 10uFC615 178-4742-78 25V 0.47uFC616 187-1053-65 50V 1uFC617 172-1041-15 50V 0.1uFC635 178-1052-78 16V 1uFC701 168-1042-78 50V 0.1uFC702 168-1042-78 50V 0.1uFC703 166-4701-50 50V 47pFC704 168-1042-78 50V 0.1uFC705 168-1532-55 50V 0.015uFC706 168-1032-55 50V 0.01uFC707 168-4722-55 50V 4700pFC708 168-1522-55 50V 1500pFC709 168-1042-78 50V 0.1uFC710 168-1042-78 50V 0.1uFC711 168-1532-55 50V 0.015uFC712 168-1042-78 50V 0.1uFC713 168-1042-78 50V 0.1uFC714 166-6811-50 50V 680pFC715 166-6801-50 50V 68pFC716 168-1042-78 50V 0.1uF

C717 178-1052-78 16V 1uFC720 178-1052-78 16V 1uFC721 187-1073-15 100-6.3VC722 178-1052-78 16V 1uFC724 187-1073-15 100-6.3VC725 187-2273-15 220-6.3VC728 168-3332-78 50V 0.033uFC729 168-6822-55 50V 6800pFC730 168-1042-78 50V 0.1uFC731 168-1042-78 50V 0.1uFC732 168-4732-78 50V 0.047uFC733 168-4732-78 50V 0.047uFC734 168-4712-55 50V 470pFC735 168-4712-55 50V 470pFC738 168-1042-78 50V 0.1uFC739 187-1073-25 10V 100uFC740 168-1042-78 50V 0.1uFC741 168-1042-78 50V 0.1uFC742 168-1042-78 50V 0.1uFC743 168-1042-78 50V 0.1uFC744 168-5622-55 50V 5600pFC745 168-1042-78 50V 0.1uFC746 178-1052-78 16V 1uFC751 168-1022-55 50V 1000pFC752 168-1022-55 50V 1000pFC753 168-1022-55 50V 1000pFC761 168-1042-78 50V 0.1uFC762 168-2222-55 50V 2200pFC763 168-1042-78 50V 0.1uFC765 168-2222-55 50V 2200pFC766 168-1042-78 50V 0.1uFC767 168-1042-78 50V 0.1uFC768 168-1042-78 50V 0.1uFC769 168-1042-78 50V 0.1uFC770 168-1042-78 50V 0.1uFC771 168-1042-78 50V 0.1uFC774 178-1052-78 16V 1uFC775 187-2273-15 6.3V 220uFC777 187-2273-15 6.3V 220uFC780 178-1052-78 16V 1uFC801 166-1011-50 50V 100pFC803 166-1011-50 50V 100pFC805 166-1011-50 50V 100pFC806 187-4763-15 6.3V 47uFC807 168-1032-55 50V 0.01uFC808 168-1022-55 50V 1000pFC809 187-1053-65 50V 1uFC810 168-1032-55 50V 0.01uFC811 166-1501-50 50V 15pFC812 166-1801-50 50V 18pFC813 168-8222-55 50V 8200pFC814 168-1222-55 50V 1200pFC901 168-1042-78 50V 0.1uFC902 187-1073-25 10V 100uFC903 187-1073-25 10V 100uFC904 168-1042-78 50V 0.1uF


REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTIONC905 168-1042-78 50V 0.1uFC906 168-1042-78 50V 0.1uFC907 168-1042-78 50V 0.1uFC908 168-1042-78 50V 0.1uFC909 168-1042-78 50V 0.1uFC910 168-1042-78 50V 0.1uFC911 187-1063-35 16V 10uFC913 042-1545-00 16V 2200pFC914 168-1022-55 50V 1000pFC915 168-1022-55 50V 1000pFC916 168-1022-55 50V 1000pFC917 168-1022-55 50V 1000pFC918 168-1022-55 50V 1000pFC919 168-1022-55 50V 1000pFC920 168-1022-55 50V 1000pFC921 168-1022-55 50V 1000pFC922 187-1053-65 50V 1uFCCT701 050-0148-51 CCT 47KD200 001-1310-00 KDS160D201 001-4312-35 02DZ6.2YD202 001-4312-35 02DZ6.2YD203 001-4312-35 02DZ6.2YD301 001-1310-00 KDS160D302 001-1310-00 KDS160D303 001-1310-00 KDS160D505 001-4312-23 02DZ4.3YD509 001-0529-43 MA8082TXD601 001-1310-00 KDS160D701 001-1313-00 KDS226D710 001-1310-00 KDS160D901 001-1310-00 KDS160D902 001-1310-00 KDS160D903 001-2003-91 1A4-JD904 001-4312-32 02DZ5.6YD905 001-4312-44 02DZ8.2YD906 001-2003-91 1A4-JD907 001-1310-00 KDS160D910 001-2003-91 1A4-JD911 001-0592-61 1N5404D912 001-4312-32 02DZ5.6YD913 001-4312-14 02DZ3.0YH-WIRE 800-0710-50 VINYL-COAT- WIREIC200 052-3971-30 uPD78F0547GKIC301 051-4620-90 LC72725KMIC302 051-3061-90 NJM14558MIC303 051-1973-38 KIC7S66FUIC401 051-5045-90 NJW1192IC501 051-3061-90 NJM14558MIC601 051-2060-00 LA47201IC701 051-6399-00 TC94A15FGIC702 051-6090-90 LA6245PIC703 051-6711-10 TA94A34FGIC704 051-3394-90 NJM2865F3-15IC801 051-6201-90 LC72146MIC901 051-3349-00 HA13166J201 074-1316-12 DCP-12PJ300 855-0593-00 3P

J601 854-4611-60 WIREJ602 854-4611-60 WIREJ701 074-1143-15 15PJ702 074-1138-60 10PJ901 074-1214-00 16PJACK601 075-9015-00 JACKJW2 060-0108-90 1/4W 0 ohmL101 010-2003-04 30uHL102 119-1011-15 1/16W 100 ohmL103 010-3001-63 5.6uHL200 010-2285-57 1K ohm/100MHzL201 117-0000-05 1/8W 0 ohmL300 001-3105-62 1K ohm/10MHzL301 010-3109-65 2K ohm/100MHzL501 117-0000-05 1/8W 0 ohmL502 117-0000-05 1/8W 0 ohmL605 010-3109-68 300 ohm/100MHzL606 010-3109-68 300 ohm/100MHzL607 010-3109-65 2K ohm/100MHzL801 010-2330-86 220uHQ101 125-2199-93 KRC103SQ102 125-0199-98 KRA118SQ103 125-0199-93 KRA103SQ104 125-2199-93 KRC103SQ106 125-4017-90 KTC4378Q301 125-2199-92 KRC103SQ302 125-2199-92 KRC102SQ303 125-3004-90 KTA1504Q601 125-4010-90 KTC3875GRQ602 125-4010-90 KTC3875GRQ603 125-0199-92 KRA102SQ701 125-3011-90 KTA1663Q703 125-8014-90 KTK5134SQ704 125-2199-93 KRC103SQ705 125-8014-90 KTK5134SQ707 125-8014-90 KTK5134SQ708 125-9022-92 RN4982Q801 125-8014-90 KTK5134SQ901 125-3007-90 KTA1298Q902 125-2199-92 KRC102SQ905 125-4010-90 KTC3875GRQ906 125-2199-92 KRC102SQ907 125-4010-90 KTC3875GRQ908 125-0199-93 KRA103SQ909 125-4010-90 KTC3875GRQ910 125-0013-97 RN2427Q911 125-2199-92 KRC102SQ913 125-9022-92 RN4982R101 119-1021-15 1/16W 1K ohmR102 119-3311-15 1/16W 330 ohmR103 119-4721-15 1/16W 24.7K ohmR105 119-1021-15 1/16W 1K ohmR107 119-1021-15 1/16W 1K ohmR108 119-4721-15 1/16W 4.7K ohmR109 119-0000-15 1/16W 0 ohmR111 119-5621-15 1/16W 5.6K ohmR112 119-0000-05 1/16W 0 ohmR113 119-2231-15 1/16w 22K ohm

R114 119-1031-15 1/16W 10K ohmR116 119-0000-05 1/16W 0 ohmR118 116-3311-15 1/4W 330 ohmR121 119-3311-15 1/16W 330 ohmR201 119-1021-15 1/16W 1K ohmR202 119-1021-15 1/16W 1K ohmR224 119-0000-05 1/16W 0 ohmR225 119-0000-05 1/16W 0 ohmR229 119-3321-15 1/16W 3.3K ohmR230 119-1041-15 1/16W 100K ohmR231 119-3321-15 1/16W 3.3K ohmR233 119-4731-15 1/16W 47K ohmR234 119-4731-15 1/16W 47K ohmR235 119-8231-15 1/16W 82K ohmR237 119-4731-15 1/16W 47K ohmR238 119-4731-15 1/16W 47K ohmR239 119-1031-15 1/16W 10K ohmR240 119-1031-15 1/16W 10K ohmR241 119-1031-15 1/16W 10K ohmR243 119-1041-15 1/16W 100K ohmR244 119-4731-15 1/16W 47K ohmR245 119-4731-15 1/16W 47K ohmR246 119-5631-15 1/16W 56K ohmR247 119-2231-15 1/16w 22K ohmR248 119-1031-15 1/16W 10K ohmR249 119-1031-15 1/16W 10K ohmR250 119-1031-15 1/16W 10K ohmR251 119-1031-15 1/16W 10K ohmR253 119-1021-15 1/16W 1K ohmR254 119-1031-15 1/16W 10K ohmR255 119-1031-15 1/16W 10K ohmR256 119-1231-15 1/16W 12K ohmR258 119-1031-15 1/16W 10K ohmR260 119-1021-15 1/16W 1K ohmR264 119-1021-15 1/16W 1K ohmR265 119-1021-15 1/16W 1K ohmR266 119-1021-15 1/16W 1K ohmR267 119-1021-15 1/16W 1K ohmR268 119-0000-05 1/16W 0 ohmR301 119-0000-05 1/16W 0 ohmR302 119-1031-15 1/16W 10K ohmR303 119-1231-15 1/16W 12K ohmR304 119-1041-15 1/16W 100K ohmR305 119-2211-15 1/16W 220 ohmR306 119-3331-15 1/16W 33K ohmR307 119-3321-15 1/16W 3.3K ohmR308 119-1021-15 1/16W 1K ohmR309 119-1021-15 1/16W 1K ohmR312 119-4721-15 1/16W 4.7K ohmR313 119-1031-15 1/16W 10K ohmR315 119-1011-15 1/16W 100 ohmR316 119-0000-05 1/16W 0 ohmR402 119-1021-15 1/16W 1K ohmR403 119-6831-15 1/16W 68K ohmR404 119-0000-05 1/16W 0 ohmR406 119-4721-15 1/16W 4.7K ohmR407 119-2221-15 1/16W 2.2K ohmR409 119-1021-15 1/16W 1K ohm


R410 119-6831-15 1/16W 68K ohmR411 119-0000-05 1/16W 0 ohmR413 119-4721-15 1/16W 4.7K ohmR414 119-2221-15 1/16W 2.2K ohmR501 032-0140-99 1/16W 39K(F) ohmR502 032-0140-00 1/16W 56K(F) ohmR503 032-0140-00 1/16W 56K(F) ohmR504 119-1041-15 1/16W 100K ohmR505 119-1041-15 1/16W 100K ohmR506 032-0140-00 1/16W 56K(F) ohmR507 032-0140-00 1/16W 56K(F) ohmR508 032-0140-99 1/16W 39K(F) ohmR509 032-0140-99 1/16W 39K(F) ohmR510 119-1021-15 1/16W 1K ohmR511 032-0140-99 1/16W 39K(F) ohmR518 119-3311-15 1/16W 330 ohmR601 119-1021-15 1/16W 1K ohmR602 119-1021-15 1/16W 1K ohmR603 119-1021-15 1/16W 1K ohmR604 119-1021-15 1/16W 1K ohmR606 119-0000-05 1/16W 0 ohmR607 119-0000-05 1/16W 0 ohmR609 119-1031-15 1/16W 10K ohmR610 119-3311-15 1/16W 330 ohmR611 119-1031-15 1/16W 10K ohmR612 119-3311-15 1/16W 330 ohmR613 119-5621-15 1/16W 5.6K ohmR614 119-5621-15 1/16W 5.6K ohmR615 119-0000-05 1/16W 0 ohmR616 119-4721-15 1/16W 4.7K ohmR617 119-1031-15 1/16W 10K ohmR618 119-4721-15 1/16W 4.7K ohmR619 119-0000-05 1/16W 0 ohmR622 119-0000-05 1/16W 0 ohmR631 119-1011-15 1/16W 100 ohmR632 119-1011-15 1/16W 100 ohmR633 119-1011-15 1/16W 100 ohmR634 119-1011-15 1/16W 100 ohmR701 119-5621-15 1/16W 5.6K ohm

R702 119-4731-15 1/16W 47K ohmR703 119-3341-15 1/16W 330K ohmR704 119-2231-15 1/16W 22K ohmR705 119-2231-15 1/16W 22K ohmR706 119-2211-15 1/16W 220 ohmR707 119-1001-15 1/16W 10 ohmR708 119-6811-15 1/16W 680 ohmR710 119-1231-15 1/16W 12K ohmR712 119-1531-15 1/16W 15K ohmR713 119-4731-15 1/16W 47K ohmR714 119-4731-15 1/16W 47K ohmR715 119-4731-15 1/16W 47K ohmR716 119-4731-15 1/16W 47K ohmR717 119-8231-15 1/16W 82K ohmR718 119-8231-15 1/16W 82K ohmR719 119-4731-15 1/16W 47K ohmR721 119-1051-15 1/16W 1M ohmR722 119-8211-15 1/16W 820 ohmR723 119-2211-15 1/16W 220 ohmR724 119-2211-15 1/16W 220 ohmR725 119-1041-15 1/16W 100K ohmR727 119-1031-15 1/16W 10K ohmR728 119-0000-05 1/16W 0 ohmR731 119-0000-05 1/16W 0 ohmR741 119-2211-15 1/16W 220 ohmR743 119-4731-15 1/16W 47K ohmR744 119-2231-15 1/16W 22K ohmR745 119-4721-15 1/16W 4.7K ohmR746 119-2221-15 1/16W 2.2K ohmR747 119-4721-15 1/16W 4.7K ohmR748 119-2221-15 1/16W 2.2K ohmR749 119-4721-15 1/16W 4.7K ohmR750 119-2221-15 1/16W 2.2K ohmR751 119-1031-15 1/16W 10K ohmR752 119-4731-15 1/16W 47K ohmR753 119-2251-15 1/16W 2.2M ohmR754 119-8211-15 1/16W 820 ohmR757 119-3321-15 1/16W 3.3K ohmR758 119-3321-15 1/16W 3.3K ohm

R760 117-0000-05 1/8W 0 ohmR761 117-0000-05 1/8W 0 ohmR762 119-2221-15 1/16W 2.2K ohmR801 119-1021-15 1/16W 1K ohmR802 119-5631-15 1/16W 56K ohmR803 119-2221-15 1/16W 2.2K ohmR804 119-1021-15 1/16W 1K ohmR805 119-2711-15 1/16W 270 ohmR806 119-1231-15 1/16W 12K ohmR807 119-6811-15 1/16W 680 ohmR901 119-2741-15 1/16W 270K ohmR902 119-1031-15 1/16W 10K ohmR904 119-2221-15 1/16W 2.2K ohmR909 119-4721-15 1/16W 4.7K ohmR910 119-4731-15 1/16W 47K ohmR911 119-1021-15 1/16W 1K ohmR912 119-2231-15 1/16w 22K ohmR913 119-1031-15 1/16W 10K ohmR914 116-2231-15 1/4W 22K ohmR915 116-1521-15 1/4W 1.5K ohmR916 119-1231-15 1/16W 12K ohmR917 119-0000-05 1/16W 0 ohmR919 119-5631-15 1/16W 56K ohmR920 119-6831-15 1/16W 68K ohmR922 119-0000-05 1/16W 0 ohmR923 119-0000-05 1/16W 0 ohmR925 119-0000-05 1/16W 0 ohmRCA601 855-5516-60 RCA JACKS200 013-3932-01 RST SWSUP101 060-0122-20 DSP-141N-S00BT901 009-9006-60 CHOKEVR101 012-4738-13 VRX200 060-1540-90 12MHzX301 061-3013-00 4.33MHzX701 060-1909-90 16.934MHzX702 060-1909-90 16.934MHzX801 061-1066-00 7.2MHzPWB 039-2998-01 PWB (WITHOUT COMPONENT)

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION


C1 168-1022-55 50V 1000pF C4 178-1052-78 16V 1uF D1 001-4312-29 02DZ5.1Y D2 001-4312-35 02DZ6.2Y D3 001-7824-90 LED (PE-2934E-A)D3 001-7820-90 LED (PE-2934E-B)D3 001-7816-90 LED (PE-2935E-A)D4 001-4312-35 02DZ6.2Y D5 001-7824-90 LED (PE-2934E-A)D5 001-7820-90 LED (PE-2934E-B)D5 001-7816-90 LED (PE-2935E-A)D6 001-4312-14 02DZ3.0X D7 001-4312-35 02DZ6.2Y D8 001-4312-35 02DZ6.2Y D9 001-7824-90 LED (PE-2934E-A)D9 001-7824-90 LED (PE-2934E-B)D9 001-7816-90 LED (PE-2935E-A)D10 001-7824-90 LED (PE-2934E-A)D10 001-7824-90 LED (PE-2934E-B)

D10 001-7816-90 LED (PE-2935E-A)D12 001-4312-29 02DZ6.2Y D14 001-7824-90 LED (PE-2934E-A)D14 001-7824-90 LED (PE-2934E-B)D14 001-7816-90 LED (PE-2935E-A)D15 001-4902-91 HZM6.8MFA IC1 051-6013-50 PT6554LQ J1 076-0703-12 PLUG LCD1 379-5019-00 LCD Q1 125-0013-97 RN2427 Q2 125-2199-92 KRC 102S Q3 125-3007-90 KTA1298 Q4 125-2199-92 KRC 102S Q5 125-2199-92 KRC 102S R1 119-4731-15 1/16W 47K ohm R2 119-1241-15 1/16W 120K ohm R3 119-3921-15 1/16W 3.9K ohmR4 119-4711-15 1/16W 470 ohmR5 119-1021-15 1/16W 1K ohm

R7 119-0000-05 1/16W 0 ohmR8 116-8201-15 1/4W 82 ohmR9 116-8201-15 1/4W 82 ohmR10 119-3311-15 1/16W 330 ohmR11 119-3311-15 1/16W 330 ohmR12 119-1221-15 1/16W 1.2K ohmR13 119-1211-15 1/16W 120 ohmR14 119-1211-15 1/16W 120 ohmR15 116-3311-15 1/4W 330 ohmR16 116-3311-15 1/4W 330 ohmR17 116-3311-15 1/4W 330 ohmR18 116-3311-15 1/4W 330 ohmR19 119-0000-05 1/16W 0 ohmR21 119-0000-05 1/16W 0 ohmR22 119-0000-05 1/16W 0 ohmR23 119-0000-05 1/16W 0 ohmVR1 016-9901-02 VR ROTARY PWB 039-2994-00 PWB (WITHOUT COMPONENT)

REF No. PART No. DESCRIPTION

Switch PWB (B2) section

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTIOND1 001-7058-90 AN1105W-RRD2 001-7058-90 AN1105W-RRJ1 074-1138-60 10P

Q1 060-4015-91 PS1192HBQ2 060-4015-91 PS1192HBS1 013-7414-50 CHUCKING

S2 013-7413-50 LIMITPWB 039-2675-20 PWB (WITHOUT COMPONENT)

Sensor PWB (B3) section

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTIONJ901 074-1285-00 ISO connectorJumper 999-0050-06 Jumper wire

Jumper 999-0125-06 Jumper wireFuse 060-0057-57 Auto-Fuse (15A)

PWB 039-2999-00 PWB (WITHOUT COMPONENT)

ISO Connector PWB (B4) section


REMOVING MAIN PWB FOR REPAIR

View from bottom side

A 311-1848-03 LOWER CASE 1 B 039-2998-01 MAIN PWB 1 C 816-4006-60 FLAT WIRE 1 D 731-3005-8B TAPTIGHT 3 E 929-5011-80 MECHANISM 1 F 313-2014-00 HEAT SINK 1 G 731-3012-8B TAPTIGHT 3 H 714-3006-8B MACHINE SCREW 2 I 731-3008-8B TAPTIGHT 4 J 714-2606-8H MACHINE SCREW 2 K 370-6288-00 INNER ESCUTCHEON 1 L - PICK-UP HEAD CABLE 1 M 714-2604-8B MC SCREW 3 N 335-0833-01 CABLE TIE 1 O 335-7501-01 FPC PROTECTOR 1 P 074-1143-15 FPC CONNECTOR 1

No. PART No. PART NAME Q’TY

Step 1Remove all screw G , H , I , from heat sink F cut off the cable tie N .

Step 2Remove heat sink F .

Step 3Remove lower case A .

Step 4Remove all screw J , from inner escutcheon K .

Step 5Remove inner escutcheon K .

Step 6Unsolder 4 points on the main PWB B , (Figure 1).

Step 7Open FPC protector O unplug the pick-up head cable L from the FPC connector P .

Step 8Remove flat wire C between main PWB B , and mechanism E .

Step 9Remove main PWB B for repairing.

Step 10Unscrew D and M from the mech brkt, if the mechanism E needs replacement.


PRINTED WIRING BOARDSWITCH PWB (B2) section

Caution:COMPONENT SIDE: Parts on the component side seen from the component side are indicated.

Caution:SOLDER SIDE: Parts on the solder side seen from the solder side are indicated.

COMPONENT SIDE SOLDER SIDE

To J

201

of M

AIN

PW

B (B

1) s

ectio

n 1/

2 (P

age

25)


PRINTED WIRING BOARDSENSOR PWB (B3) section

CIRCUIT DIAGRAMSENSOR PWB (B3) section

To J702 of MAIN PWB (B1)section 1/2 (Page 25)with FLAT WIRE 816-4006-60

To J701 ofMAIN PWB (B1)section 2/2(Page 26)

Documents

Clarion Db178rmp Db179rmp