CISCO 360 CCIE R&S ADVANCED WORKSHOP 1 V5.0 ... Lab 8-1: Establishing Basic Connectivity for Catalyst Switch QoS o Lab 8-2: Exploring Catalyst 3560 Series QoS Concepts o Lab 8-3: Implementing

SUNSET LEARNING INSTITUTE CLOUD TECHNOLOGY TRAINING PROVIDER - EDUCATE. INNOVATE. OPTIMIZE.

888.888.5251 | www.sunsetlearning.com

CISCO 360 CCIE R&S ADVANCED WORKSHOP 1 V5.0

(CIERS1)

COURSE OVERVIEW: Cisco 360 CCIE R&S Advanced Workshop 1 (CIERS1) v5.0 teaches learners how to use an expert-level problem-solving process that includes options analysis to support complex network technologies and topologies. This course is part of a blended learning curriculum that supports expert-level preparation in routing and switching.

WHO WILL BENEFIT FROM THIS COURSE? The primary audience for this course is network engineers that need be able to use an expert-level

problem-solving process that includes options analysis to support complex network technologies and topologies.

The secondary audience is network designers that design and support complex network technologies and topologies.

PREREQUISITES: To fully benefit from this course, students should have the following prerequisite skills and knowledge:

Layer 2 and Layer 3 switching skills

IPv6 fundamentals

RIP, EIGRP, and OSPF configuration skills for both IPv4 and IPv6

BGP configuration skills

Multicast configuration skills

QoS configuration skills

Intermediate-level troubleshooting skills for all technologies listed

RELATED COURSES: CIERS2

COURSE OBJECTIVES: After completion of this course, students will be able to...

Describe the Cisco 360 Learning Program for CCIE R&S and explain how it addresses expert-level networking issues

Discuss your baseline status for Cisco CCIE® lab readiness

Resolve expert-level Layer 2 and DMVPN task analysis, configuration and troubleshooting issues

Resolve expert-level core task analysis, configuration, and troubleshooting issues

Resolve expert-level BGP issues from both a configuration and troubleshooting perspective

Resolve expert-level MPLS L3 VPN configuration tasks.

Resolve expert-level multicast task analysis, configuration, and troubleshooting issues

Resolve expert-level IP connectivity issues regardless of whether they involve IPv4 or IPv6

Resolve expert-level router MQC QoS task analysis, configuration, and troubleshooting issues

Resolve expert-level Network Services task analysis, configuration, and troubleshooting issues

Resolve expert-level multitopic core and advanced task analysis, configuration, and troubleshooting issues



COURSE OUTLINE:

Module 1: Cisco 360 Learning Program for CCIE R&S Lesson 1: Introducing the Cisco 360 Learning Program for CCIE R&S

Define what it means to be an internetworking expert

Discuss common questions asked by CCIE candidates

Discuss the Cisco 360 CCIE R&S blended learning domain

Describe the Cisco 360 CCIE R&S blended learning resources that are available to develop expert- level networking skills

The lesson includes these topics: o What Is an Internetworking Expert? o Common Questions Asked by CCIE Candidates o Cisco 360 CCIE R&S Domain o Cisco 360 CCIE R&S blended learning resources

Lesson 2: Preparing for the Cisco CCIE Lab Exam

Discuss why a structured approach to CCIE lab preparation is needed

Describe how modularization supports lab preparation and task configuration

Discuss the Cisco 360 CCIE R&S problem-solving process using Options Analysis diagrams

Describe the two problem or task formats encountered in the Routing and Switching CCIE lab: configuration tasks and troubleshooting tasks

Describe how Cisco 360 CCIE R&S assessments measure progress and define next steps in the expert- level routing and switching preparation process

Module 2: Core Task Assessment Lesson 1: Applying the Cisco 360 CCIE R&S Opening-Moves Strategy to Cisco CCIE Labs

Describe a structured set of well-defined opening moves to modularize the lab tasks

Construct topology diagrams and a task-tracking worksheet as an implementation roadmap

Apply these opening moves to Cisco 360 CCIE R&S Advanced Workshop 1 Assessment Lab 1

The lesson includes these topics: o Applying the Cisco 360 CCIE R&S Problem-Solving Process to CCIE-Level Labs o Using Preconfiguration Tools on the CCIE Lab o Previewing CIERSASSESS-1 o Lab 2-1: CIERSASSESS-1

Lesson 2: Analyzing the Cisco 360 CCIE R&S Assessment Results Report

Discuss how to interpret their lab performance based on the Cisco 360 CCIE R&S Assessment Results Report

Plan their next Cisco CCIE® preparation steps based on the Cisco 360 CCIE R&S Assessment Results Report

The lesson includes these topics: o Using the Cisco 360 CCIE R&S Assessment Results Report o Planning Your Next Steps from Your Results Report

Module 3: Core Task Analysis and Configuration Lesson 1: Resolving DMVPN Tasks

Describe DMVPN technology

Develop strategies to configure and verify DMVPN

Describe potential DMVPN issues and tools to avoid these issues

Develop strategies to troubleshoot DMVPN

Discuss next steps for CCIE lab preparation with DMVPN technology



Lesson 2: Resolving Layer 2 Tasks

Describe Serial interface encapsulation options

Develop strategies to configure and verify PPP options

Develop strategies to troubleshoot serial encapsulation

Develop strategies to configure and verify PPP over Ethernet options

Describe Ethernet switching technologies

Develop strategies to configure and verify Ethernet switching tasks

Describe potential Ethernet switching issues and tools to avoid these issues

Develop strategies to troubleshoot Ethernet switching Lesson 3: Resolving IGP Tasks

Describe the role of routing protocols in the network

Develop strategies to configure, troubleshoot, and verify RIP tasks

Develop strategies to configure, troubleshoot, and verify EIGRP and EIGRPv6 tasks

Develop strategies to configure, troubleshoot, and verify OSPFv2 and OSPFv3 tasks

Compare routing protocols and discuss tools to avoid potential issues

Discuss next steps for CCIE lab exam preparation with routing protocols Lesson 4: Resolving Redistribution Tasks

Describe redistribution and its potential issues

Develop strategies to configure, troubleshoot, and verify redistribution tasks

Discuss next steps for CCIE lab exam preparation with redistribution

The lesson includes these topics: o Reviewing Redistribution o Identifying Configuration, Troubleshooting and Verification Strategies for Redistribution

Tasks o CCIE Lab Exam Tips for Redistribution Tasks

Module 4: BGP Task Analysis and Configuration Lesson 1: Reviewing Basic BGP Operations

Describe BGP fundamentals

Configure and verify basic BGP peering for both IPv4 and IPv6

Describe options for originating routes into BGP

Discuss issues in BGP route advertisement for both IPv4 and IPv6 Lesson 2: Resolving Advanced BGP Tasks

Describe and configure advanced BGP peering options for both IPv4 and IPv6

Develop strategies to analyze and resolve interactions between BGP and the underlying Layer 3 topology

Discuss how BGP synchronization rules affect data movement

Discuss strategies to analyze and resolve multiple BGP update filtering requirements on a router

Develop strategies to analyze and resolve BGP path determination options

Develop a strategy to troubleshoot pre-existing BGP implementations

The lesson includes these activities: o Lab 4-1: Establishing Basic Connectivity for BGP o Lab 4-2: Configuring BGP o Lab 4-3: Filtering BGP Updates and Path Determination



Module 5: MPLS Layer 3 VPNs Lesson 1: Reviewing Basic MPLS VPN Operations

Discuss the concept of enabling privacy by controlling routing tables

Configure OSPF, LDP, and BGP to support core connectivity

Create customer VRFs on provider edge routers

Enable static, RIP, and OSPF routing processes between PE and CE routers

Explain how the OSPF route tag prevents potential routing loops and how a sham link is used to optimize paths

Configure methods of adding non-VPN routes to a VRF instance

The lesson includes these activities: o Lab 5-1: Establishing Basic Connectivity for MPLS Layer 3 VPNs o Lab 5-2: Configuring the MPLS Core o Lab 5-3: Creating VPNs and Enabling VPN Routing o Lab 5-4: Adding a Backup Link in VPNA

Module 6: Multicast Task Analysis and Configuration Lesson 1: Reviewing Basic Multicast Operations

Describe multicast technology

Discuss multicast addressing

Discuss multicast group membership

Describe PIM-DM operations

Discuss potential issues with PIM and ways to resolve these issues

The lesson includes these activities: o Lab 6-1: Establishing Basic Connectivity for Multicast o Lab 6-2: Configuring Dense Mode IP Multicast Routing

Lesson 2: Resolving PIM Sparse Mode Multicast Tasks

Discuss the differences and similarities in multicast modes

Describe PIM-SM configuration and operations

Discuss RP considerations with PIM-SM

Discuss how to analyze, configure, and troubleshoot pre-existing IP multicast configurations, with emphasis on PIM-SM

Discuss next steps for CCIE lab exam preparation with multicast technology

The lesson includes this activity: o Lab 6-3: Configuring PIM Sparse Mode

Module 7: Router MQC QoS Task Analysis and Configuration Lesson 1: Reviewing MQC QoS and DiffServ

Describe Cisco MQC router tools

Describe the significant characteristics of the DiffServ IP QoS architecture Lesson 2: Using DiffServ Tools

Use the MQC DiffServ edge tools for class-based shaping

Use the MQC DiffServ edge tools for class-based policing

Use the MQC DiffServ edge tools for marking traffic with the MQC set command



The lesson includes these activities: o Directed Activity 7-1: Examining Operation of the shape average Command o Directed Activity 7-2: Examining Operation of a Modified shape average Command o Directed Activity 7-3: Examining the shape average Command When Be = 0 o Directed Activity 7-4: Configuring the shape peak Command o Directed Activity 7-5: Configuring the MQC shape Command with the percent Option o Directed Activity 7-6: Configuring a Single-Rate Two-Color Marker o Directed Activity 7-7: Configuring a Single-Rate Two-Color Marker with Large Conform Burst o Directed Activity 7-8: Configuring a Single-Rate Three-Color Marker

Lesson 3: Using Congestion Management and Avoidance Tools

Use the MQC congestion management tools

Use the MQC congestion avoidance tools

The lesson includes these activities: o Directed Activity 7-9: Configuring Basic LLQ o Directed Activity 7-10: Configuring LLQ and Manipulating the max-reserved-bandwidth

Command o Directed Activity 7-11: Configuring the priority Command with LLQ

Lesson 4: Identifying Strategies for Router MQC QoS Tasks

Determine strategies for traffic classification

Determine the QoS policy needed for a task

Determine how to apply the MQC policy map

Describe formulating a strategy to troubleshoot a pre-existing router QoS configuration involving the MQC

Module 8: Cisco Network Services Task Analysis and Configuration Lesson 1: Cisco Network Services per the CCIE R&S v5.0 Blue Print

Discuss which First Hop Redundancy Protocols are available for both IPv4 and IPv6 and their available options

Discuss Dynamic Host Configuration Protocol for both IPv4 and IPv6 and their available options

Discuss Network Time protocol, the different versions and differences

Describe the function and options for Network Address Translation

Formulate a strategy for troubleshooting a pre-existing Network Services configuration

Discuss next steps for Cisco CCIE lab preparation for Cisco Network Services

The lesson includes these activities: o Lab 8-1: Implementing FHRP for IPv4 and IPv6 o Lab 8-2: Implementing DHCP and DHCPv6 o Lab 8-3: Implementing NTP o Lab 8-4: Implementing NAT

Module 9: Cisco Network Troubleshooting Lab 9-1: CIERSASSESS-2

Data Link Troubleshooting (DMVPN and PPP)

Network Layer Troubleshooting (IGPs, BGP, IPv6 and MPLS L3 VPNs)

Multicast Network Troubleshooting

Network Application Troubleshooting (QoS)

Network Services Troubleshooting (NTP)

Network Security Troubleshooting (MPPE)



The lab includes these configuration activities:

DMVPN and Serial Communications

Catalyst Switch

IPv4 OSPF

IPv4 EIGRP

IPv4 RIP

BGP

IPv6 Routing

Security

QoS

DHCP

Address Administration

Gateway Redundancy

Multicast

MPLS Appendix A: Cisco Catalyst Switch QoS Task Analysis and Configuration Lesson 1: Ensuring QoS for the Catalyst 3560 Series Switch

Discuss the implications of enabling the QoS process on the Catalyst 3560 Series

Discuss trust options for supporting QoS on the Catalyst 3560 Series

Use the MQC to provide class-based and VLAN-based QoS services

Describe the options available to enhance output queuing

Describe the use of the AutoQoS macros to support VoIP on the Catalyst 3560 Series

Formulate a strategy for troubleshooting a pre-existing Catalyst QoS configuration

Discuss next steps for Cisco CCIE lab preparation with Catalyst QoS

The lesson includes these activities: o Lab 8-1: Establishing Basic Connectivity for Catalyst Switch QoS o Lab 8-2: Exploring Catalyst 3560 Series QoS Concepts o Lab 8-3: Implementing VLAN-Based QoS

Appendix B: Strengthening IPv4 Skills by Learning IPv6 The appendix includes these topics:

Reviewing IPv6

IPv6 Address Assignment

Configuring IPv6 on Links

Tunneling IPv6

IPv6 IGP Routing

IPv6 Redistribution

Troubleshooting a Pre-Existing IPv6 Configuration

The appendix includes these activities:

o Directed Activity B-1: Enabling IPv6 on a Catalyst 3560 Switch o Directed Activity B-2: IPv6 Addressing Using a Static Prefix and Static Interface ID o Directed Activity B-3: Configuring IPv6 over Frame Relay o Directed Activity B-4: Configuring IPv6 over an ISATAP Tunnel o Directed Activity B-5: Enabling OSPFv3 over a Frame Relay Link o Directed Activity B-6: Summarizing a Set of IPv6 Prefixes with OSPFv3 o Directed Activity B-7: Configuring OSPFv3 over ISATAP o Directed Activity B-8: Configuring RIPng o Directed Activity B-9: Performing Redistribution between OSPFv3 and RIPng o Directed Activity B-10: Filtering a RIPng External Prefix from OSPFv3

SUNSET LEARNING INSTITUTE (SLI) DIFFERENTIATORS: Sunset Learning Institute (SLI) has been an innovative leader in developing and delivering authorized technical training since 1996. Our goal is to help our customers optimize their cloud technology investments by providing convenient, high quality technical training that our customers can rely on. We empower students to master their desired technologies for their unique environments. What sets SLI apart is not only our immense selection of trainings options, but our convenient and consistent delivery system. No matter how complex your environment is or where you are located, SLI is sure to have a training solution that you can count on!



Premiere World Class Instruction Team

All SLI instructors have a four-year technical degree, instructor level certifications and field

consulting work experience.

Sunset Learning has won numerous Instructor Excellence and Instructor Quality Distinction awards

since 2012

Enhanced Learning Experience

The goal of our instructors during class is ensure students understand the material, guide them

through our labs and encourage questions and interactive discussions.

Convenient and Reliable Training Experience

You have the option to attend at any of our established training facilities or from the convenience of

your home or office with the use of our HD-ILT network (High Definition Instructor Led Team)

All Sunset Learning Institute classes are guaranteed to run – you can count on us to deliver the

training you need when you need it!

Outstanding Customer Service

Dedicated account manager to suggest the optimal learning path for you and your team

Enthusiastic Student Services team available to answer any questions and ensure a quality training

experience during your week at Sunset Learning Institute

Documents

CISCO 360 CCIE R&S ADVANCED WORKSHOP 1 V5.0 ... Lab 8-1: Establishing Basic Connectivity for Catalyst Switch QoS o Lab 8-2: Exploring Catalyst 3560 Series QoS Concepts o Lab 8-3: Implementing