Upload
petkovic1961
View
214
Download
0
Embed Size (px)
Citation preview
7/27/2019 CHOICE STABLE MIXTURE UNLEADED GASOLINS FOR VEHICLES WITH 3,5 AND 10% ETHANOL AND 0,1, 0,2, 0,3 0,5 AND 1% WATER
1/5
VInternational Congress MotorVehicles & Motors 2006
Kragujevac, October 4th-6th, 2006
MVM2006NNNN
Peanac M.1
Radovanovi M.2
Petkovi S.3
CHOICE STABLE MIXTURE UNLEADED GASOLINS FORVEHICLES WITH 3,5 AND 10% ETHANOL AND 0,1, 0,2, 0,30,5 AND 1% WATER
ABSTRACT: Products of the fossil fuels combustion damages flora and fauna. To reduce the consequences ofthe damages caused by the combustion products, the law regulations are getting stricter in order to reduce theallowed amounts of the partial combustion products. We introduce alternative fuels gradually with the same aim.Among all the fuels produced from the renewable sources, besides biodiesel, alcohols are considered the mostacceptable alternative fuel.Ethyl alcohol is used in the various relations with gasoline. Problem with the mixture is the separation. It is shown inthe paper the possibility of production and selection of the stabile mixture of the unleaded motor gasoline and ethylalcohol.
KEYWORDS: unleaded gasoline, ethyl alcohol, separation, ecology.
INTRODUCTION
Biomass presents the great potential for the production of the alternative fuels, that is, fuels of the non-oil origin.The possible products from the biomass are [2]:
Bioethanol
Biomethanol
Biodiesel
Biogas
Biodimethilethar
Bio ETBE (Ethyl Tercial Butyl Ether)
Bio MTBE (Methyl Tercial Butyl Ether)
Synthetical biofuel Pure plant oil.
The utilization of the ethanol produced from the biomass (bioethanol) has numerous advantages comparing it witha gasoline, mostly because of the reduced emission of carbon dioxide as the main cause of the greenhouse effect.The advantages of ethanol utilization are: more complete combustion, lower carbon dioxide, carbon monoxide andaromatic hydrocarbon emission, increased power, torque and octane number. Disadvantages are: highervolumetric consumption, mass separation and aggressive influence on some materials.
The directive 2003/30/EC of the European Parliament and of the Council of 8 May 2003 promote the utilization ofthe biofuels or other renewable transport fuels. Oil fuels for the transport in the EU are 98% currently. The transportsector uses more than 30% of final energy consumption in the EU. The main aim of the directive is to reduce thecarbon dioxide emission which would rise for 50% until 2010 (around 1113 million tones) and to reduce the EU
1 Author's name, affiliation, company, address, e-mail2Co-author's name, affiliation, company, address, e-mail3Co-author's name, affiliation, company, address, e-mail
1
7/27/2019 CHOICE STABLE MIXTURE UNLEADED GASOLINS FOR VEHICLES WITH 3,5 AND 10% ETHANOL AND 0,1, 0,2, 0,3 0,5 AND 1% WATER
2/5
dependence on the oil [2]. The directive has predicted the increase of the biofuel utilization in the road transportfrom 6% in 2000 to the 20% in 2020. As the result of the technological improvement, the great number of thevehicles in the EU is capable for utilization of the low biofuel concentration without modification. In some states ofthe EU biofuels make 10% and even more. In America, E10 and E85 are utilised, that is, content of up to10 and 85of bioethanol in a mixture with unleaded gasoline is in use. In Brazil it is up to 22% [3].
To achieve the aim of the directive, states of the EU should reduce taxes in favour of biofuels, to introduce the lawlegislative for a minimum biofuel blend in conventional fuel and to force the motor vehicle producers to insure thevehicle flexibility for usage of the biofuel or the mixture and conventional fuel.
Consumers will accept the alternative fuel if there is it in the sufficient amounts and if the price is competitive.Depending on the motor vehicle adoption, biofuels can be used in its pure form or in the mixture with aconventional fuel.
In this paper the stabilizer is chosen for the stable mixture of the unleaded fuel and 3,5 and 10% ethilalcohole with0.1, 0.2, 0.3, 0.5 and 1% of water.
TEST PROGRAM
Includes the determination of:
Physical and chemical characteristics of BMB 95 and ethanol and BMB 95 mixture (BMB-unleaded motor
gasoline),
Selection of the appropriate stabilizer,
Selection of the stable mixture for the climate conditions.
The characteristics of the utilized unleaded motor gasoline are determined according to the standard EN 228.Distillation curve of the unleaded motor gasoline and ethanol is determined according to the Yugoslavianstandard JUS B.H8.028.
Tercial butyl alcohol (TBA (CH3)COH) and isopropyl alcohol (IPA C3H7OH) are used as stabilizers. Duringthe preliminary investigations, TBA showed as better stabilizer and it was used during the examination.
Characteristics of the absolute ethanol (p.a.) are taken from the alcohol producer and they are shown in a table.
In a practice, it is extremely important that in all exploitation conditions, motor gasoline ethanol mixture remainhomogeneous. To choose a stabile mixture it is necessary to know the stabilizer type and temperature atwhich it comes to the separation on two phases: lower phase of ethanol and upper phase of gasoline. Watercontent and impurity content contribute to this phenomenon as well as low environment temperature.
Separation temperature is the extreme temperature during the cooling of the gasoline ethanol mixture at which theseparation at two phases occurred.
During the test, concentration 3,5 and 10% v/v ethanol with 0.1, 0.2, 0.3, 0.5 with 1% of water was used.Separation was demonstrated in the shape of drops on the mixture bottom, which is not a common two-phase separation. Such a separation is shown on the Figure 4 in the Results.
RESULTS AND ANALYSIS OF THE EXPERIMENT RESULTS
Analysis of the unleaded gasoline 95, permitted values according to the EN 228 and test methods are given inTable 1.
Analysis of the absolute ethanol, according to the JUS H.G3.101 is given in Table 2, based on the data received
from the producer.
2
7/27/2019 CHOICE STABLE MIXTURE UNLEADED GASOLINS FOR VEHICLES WITH 3,5 AND 10% ETHANOL AND 0,1, 0,2, 0,3 0,5 AND 1% WATER
3/5
Table 1 Analysis primary sample of fuel ( unleaded gasoline)
Characterictic
Primary
sample
gasoline
Regulation Test method
Density at 15C (kg/m3)759
No regulate,
just recordedEN ISO12815
Copper strip corrosion (3 hour at 50
C) 1 1b JUS ISO2160
Octane rating 95.5 Min. 95ASTM D
2699
Reid Pressure (bar) 0.52 Min. 0.7* JUS B.H7.030
Relation vapour/liquid 36:1 (C) 67.6 Min. 53 calculated
* for summer period from May 1 to September 30
Table 2 Ethanol characteristics p.a. (JUS H.G3.101)
Characterictic Value
Ethanol contents Min. 99.8 %
Density at 20 C 0.791-0792 kg/m3
Interval distillation 77.5-78.5
CMixing with water According to regulation
No evaporable matter maximal 0.001%
Free acid -
CH3COOH maximal 0.003%
Free alkali (NH3) maximal 0.0001%
Resistance to KMnO4 5 minute
thanol content (CH3OH) According to regulation
cetone content (CH3COCH3) maximal 0.001%
Aldechides content (CH3COH) According to regulation
Furfural content maximal 0.0001%
elasa According to regulation
anin
Hard metal (Pb)
According to regulation
maximal 0,0001%
Taste and smell Specific
Appearance Clear and colourless
Results during the selection of the stabilizer are shown in the Figure 1, the selected stabilizer is Tercial ButylAlcohol (TBA).
-30
-20
-10
0
10
20
30
3 4 5 6 7 8 9 10
% v/v EA
TemperaturemixtureC
BMB-95 + 0.1% water +1%
(TBA or IPA)
BMB-95 + 0.1% water + 2%
( TBA or IPA)
BMB-95 + 0.1% water +
3% TBA
BMB-95 + 0.1% water +
3% IPA
Figure 1 Selection of the stabilizer.
3
7/27/2019 CHOICE STABLE MIXTURE UNLEADED GASOLINS FOR VEHICLES WITH 3,5 AND 10% ETHANOL AND 0,1, 0,2, 0,3 0,5 AND 1% WATER
4/5
Figure 2. shows the distillation curves of BMB 95 and mixture of BMB 95 +10% EA + 0.3% of water.
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
0 10 20 30 40 50 60 70 80 90 100
Destillate ( v/v %)
Temperaturedistillation
BMB-95+10%EA +
0.3%w ater+2% TBA
BMB-95
Figure 2Distillation curves
The stabile mixture for the certain climate conditions was chosen from the figure 3. (3.a,3.b,3.c)
Sub-sub-heading 1
If you need sub-sub-headings, please use the Heading 3 style. Use capital and small letters. Do not leave a line ofspace above and below these headings.
MAIN HEADING 2
Here are some practical hints for using bulleted lists, equations, tables and figures in the text of the paper.
If you need to use an unordered list using bullets, please use the Unordered list style:
This is an unordered list using bullets.
This is the second item in the list.
This is the third item in the list.
If you need to use an ordered list using bullets, please use the Ordered list style:1. This is an ordered list, using numbers.2. This is the second item in the list.3. This is the third item in the list.
Equations should be written using the Equation editor, according to the following style, centred at the left column ofthe table. The right column of the table contains (centred) the number of the equation in the brackets. The applied
table has no visible cell borders. Leave a blank line before and after the table containing the equation:
++= ibax 12
(1)
4
7/27/2019 CHOICE STABLE MIXTURE UNLEADED GASOLINS FOR VEHICLES WITH 3,5 AND 10% ETHANOL AND 0,1, 0,2, 0,3 0,5 AND 1% WATER
5/5
All equations must be numbered consecutively:
++= ibax 12
(2)
Tables should be centred. The title of the Table is centred and written just above the table, using the Table namestyle. Tables are numbered consecutively.
Table 1 Type the table title here (Table title text + style)
All illustrations, photos, graphics, etc. must be embedded as Figures into the document. Separate graphic files arenot accepted. Line art must be professionally drawn and photos must be high quality with adequate contrast.Figures are inserted into the paper, centred with layout in line with text. The titles of the Figures should be writtenunder the Figure, centred, using Figure title style. Please number figures consecutively. Live a blank line before theFigure and another one after the Figure title.
VFigure 1 Type the title of the Figure here
CONCLUSIONS
Type your conclusions here.
ACKNOWLEDGMENTS
Here is the Acknowledgment section. This is an optional section.
REFERENCES
[1] References should be cited according to alphabetical order and prepared according to References style,[2] The surname of the author, the first letter of name., co-authors surname and the first letter of name.:
Reference title, Journal (or Monograph, Congress, Proceedings, etc), Vol., No., Year of publishing, place,pages,
[3] Reference 3,[4] Reference 4,[5] Reference 5.
5