Upload
pradeepknvp
View
185
Download
2
Tags:
Embed Size (px)
Citation preview
Check Point QoSAdministration Guide
Version NGX R65
700726 January 2007
© 2003-2007 Check Point Software Technologies Ltd.
All rights reserved. This product and related documentation are protected by copyright and distributed under licensing restricting their use, copying, distribution, and decompilation. No part of this product or related documentation may be reproduced in any form or by any means without prior written authorization of Check Point. While every precaution has been taken in the preparation of this book, Check Point assumes no responsibility for errors or omissions. This publication and features described herein are subject to change without notice.
RESTRICTED RIGHTS LEGEND:
Use, duplication, or disclosure by the government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and FAR 52.227-19.
TRADEMARKS:
©2003-2007 Check Point Software Technologies Ltd. All rights reserved. Check Point, AlertAdvisor, Application Intelligence, Check Point Express, Check Point Express CI, the Check Point logo, ClusterXL, Confidence Indexing, ConnectControl, Connectra, Connectra Accelerator Card, Cooperative Enforcement, Cooperative Security Alliance, CoSa, DefenseNet, Dynamic Shielding Architecture, Eventia, Eventia Analyzer, Eventia Reporter, Eventia Suite, FireWall-1, FireWall-1 GX, FireWall-1 SecureServer, FloodGate-1, Hacker ID, Hybrid Detection Engine, IMsecure, INSPECT, INSPECT XL, Integrity, Integrity Clientless Security, Integrity SecureClient, InterSpect, IPS-1, IQ Engine, MailSafe, NG, NGX, Open Security Extension, OPSEC, OSFirewall, Policy Lifecycle Management, Provider-1, Safe@Home, Safe@Office, SecureClient, SecureClient Mobile, SecureKnowledge, SecurePlatform, SecurePlatform Pro, SecuRemote, SecureServer, SecureUpdate, SecureXL, SecureXL Turbocard, Sentivist, SiteManager-1, SmartCenter, SmartCenter Express, SmartCenter Power, SmartCenter Pro, SmartCenter UTM, SmartConsole, SmartDashboard, SmartDefense, SmartDefense Advisor, Smarter Security, SmartLSM, SmartMap, SmartPortal, SmartUpdate, SmartView, SmartView Monitor, SmartView Reporter, SmartView Status, SmartViewTracker, SofaWare, SSL Network Extender, Stateful Clustering, TrueVector, Turbocard, UAM, UserAuthority, User-to-Address Mapping, VPN-1, VPN-1 Accelerator Card, VPN-1 Edge, VPN-1 Express, VPN-1 Express CI, VPN-1 Power, VPN-1 Power VSX, VPN-1 Pro, VPN-1 SecureClient, VPN-1 SecuRemote, VPN-1 SecureServer, VPN-1 UTM, VPN-1 UTM Edge, VPN-1 VSX, Web Intelligence, ZoneAlarm, ZoneAlarm Anti-Spyware, ZoneAlarm Antivirus, ZoneAlarm Internet Security Suite, ZoneAlarm Pro, ZoneAlarm Secure Wireless Router, Zone Labs, and the Zone Labs logo are trademarks or registered trademarks of Check Point Software Technologies Ltd. or its affiliates. ZoneAlarm is a Check Point Software Technologies, Inc. Company. All other product names mentioned herein are trademarks or registered trademarks of their respective owners. The products described in this document are protected by U.S. Patent No. 5,606,668, 5,835,726, 6,496,935, 6,873,988, and 6,850,943 and may be protected by other U.S. Patents, foreign patents, or pending applications.
For third party notices, see: THIRD PARTY TRADEMARKS AND COPYRIGHTS.
Table of Contents 5
Contents
Preface Who Should Use This Guide.............................................................................. 10Summary of Contents ....................................................................................... 11
Appendices ................................................................................................ 11Related Documentation .................................................................................... 12More Information ............................................................................................. 15Feedback ........................................................................................................ 16
Chapter 1 Overview What is Quality of Service................................................................................. 18Internet Bandwidth Management Technologies ................................................... 19
Overview .................................................................................................... 19Superior QoS Solution Requirements ............................................................ 19Benefits of a Policy-Based Solution .............................................................. 20
How Does Check Point Deliver QoS.................................................................... 21Features and Benefits ...................................................................................... 23Traditional Check Point QoS vs. Check Point QoS Express ................................... 24Workflow......................................................................................................... 26
Chapter 2 Introduction to Check Point QoS Check Point QoS’s Innovative Technology........................................................... 30
Technology Overview ................................................................................... 31Check Point QoS Architecture ........................................................................... 33
Basic Architecture ...................................................................................... 33Check Point QoS Configuration..................................................................... 35Concurrent Sessions.................................................................................... 38
Interaction with VPN-1Pro and VPN-1 Net ......................................................... 39Interoperability ........................................................................................... 39
Chapter 3 Basic QoS Policy Management Overview ......................................................................................................... 42Rule Base Management.................................................................................... 43
Overview .................................................................................................... 43Connection Classification............................................................................. 44Network Objects ......................................................................................... 44Services and Resources ............................................................................... 45Time Objects.............................................................................................. 45Bandwidth Allocation and Rules ................................................................... 45Default Rule............................................................................................... 47QoS Action Properties ................................................................................. 47Example of a Rule Matching VPN Traffic....................................................... 48Bandwidth Allocation and Sub-Rules ............................................................ 49
6
Implementing the Rule Base............................................................................. 51To Verify and View the QoS Policy ................................................................ 51To Install and Enforce the Policy .................................................................. 51To Uninstall the QoS Policy ......................................................................... 52To Monitor the QoS Policy ........................................................................... 52
Chapter 4 Check Point QoS Tutorial Introduction .................................................................................................... 54Building and Installing a QoS Policy .................................................................. 56
Step 1: Installing Check Point Modules......................................................... 57Step 2: Starting SmartDashboard ................................................................. 57To Start SmartDashboard............................................................................. 58Step 3: Determining QoS Policy ................................................................... 61Step 4: Defining the Network Objects ........................................................... 61To Define the Gateway London ..................................................................... 62To Define the Interfaces on Gateway London ................................................. 66To Define the QoS Properties for the Interfaces on Gateway London................. 72Step 5: Defining the Services....................................................................... 73Step 6: Creating a Rule Base ....................................................................... 73To Create a New Policy Package................................................................... 74To Create a New Rules ................................................................................ 75To Modify New Rules .................................................................................. 76Step 7: Installing a QoS Policy..................................................................... 82
Conclusion ...................................................................................................... 84
Chapter 5 Advanced QoS Policy Management Overview ......................................................................................................... 86Examples: Guarantees and Limits...................................................................... 87
Per Rule Guarantees ................................................................................... 87Per Connections Guarantees ........................................................................ 90Limits........................................................................................................ 91Guarantee - Limit Interaction ....................................................................... 91
Differentiated Services (DiffServ) ...................................................................... 93Overview .................................................................................................... 93DiffServ Markings for IPSec Packets ............................................................. 93Interaction Between DiffServ Rules and Other Rules ...................................... 94
Low Latency Queuing ....................................................................................... 95Overview .................................................................................................... 95Low Latency Classes ................................................................................... 95Interaction between Low Latency and Other Rule Properties.......................... 100When to Use Low Latency Queuing............................................................. 101Low Latency versus DiffServ....................................................................... 102
Authenticated QoS......................................................................................... 103Citrix MetaFrame Support............................................................................... 104
Overview .................................................................................................. 104Limitations............................................................................................... 105
Load Sharing................................................................................................. 106Overview .................................................................................................. 106
Table of Contents 7
Check Point QoS Cluster Infrastructure ....................................................... 107
Chapter 6 Managing Check Point QoS Defining QoS Global Properties ....................................................................... 112
To Modify the QoS Global Properties........................................................... 112Specifying Interface QoS Properties................................................................. 114
To Define the Interface QoS Properties ....................................................... 114Editing QoS Rule Bases.................................................................................. 118
To Create a New Policy Package ................................................................. 118To Open an Existing Policy Package............................................................ 119To Add a Rule .......................................................................................... 119To Rename a Rule .................................................................................... 121To Copy, Cut or Paste a Rule...................................................................... 121To Delete a Rule ....................................................................................... 122
Modifying Rules............................................................................................. 123Modifying Sources in a Rule ...................................................................... 123Modifying Destinations in a Rule ................................................................ 126Modifying Services in a Rule ...................................................................... 128Modifying Rule Actions.............................................................................. 130Modifying Tracking for a Rule .................................................................... 135Modifying Install On for a Rule................................................................... 135Modifying Time in a Rule........................................................................... 138Adding Comments to a Rule....................................................................... 140
Defining Sub-Rules ........................................................................................ 142Working with Differentiated Services (DiffServ) ................................................. 144
To Define a DiffServ Class of Service .......................................................... 145To Define a DiffServ Class of Service Group................................................. 146To Add QoS Class Properties for Expedited Forwarding ................................. 147To Add QoS Class Properties for Non Expedited Forwarding .......................... 148
Working with Low Latency Classes................................................................... 150To Implement Low Latency Queuing ........................................................... 150To Define Low Latency Classes of Service.................................................... 151To Define Class of Service Properties for Low Latency Queuing...................... 151
Working with Authenticated QoS ..................................................................... 153To Use Authenticated QoS......................................................................... 153
Managing QoS for Citrix ICA Applications ......................................................... 155Disabling Session Sharing.......................................................................... 155Modifying your Security Policy ................................................................... 156Discovering Citrix ICA Application Names.................................................... 157Defining a New Citrix TCP Service .............................................................. 160Adding a Citrix TCP Service to a Rule (Traditional Mode Only)....................... 161Installing the Security and QoS Policies ...................................................... 161
Managing QoS for Citrix Printing ..................................................................... 162Configuring a Citrix Printing Rule (Traditional Mode Only)............................. 162Configuring Check Point QoS Topology........................................................ 163
Viewing the Check Point QoS Modules Status ................................................... 164To Display the Status of Check Point QoS Modules Controlled by the SmartCenter
Server ................................................................................................... 164
8
Enabling Log Collection.................................................................................. 165To Turn on QoS Logging ............................................................................ 165To Confirm that the Rule is Marked for Logging ........................................... 166To Start SmartView Tracker........................................................................ 167
Chapter 7 SmartView Tracker Overview of Logging ....................................................................................... 170Examples of Log Events.................................................................................. 174
Connection Reject Log .............................................................................. 174LLQ Drop Log ........................................................................................... 174Pool Exceeded Log.................................................................................... 175
Examples of Account Statistics Logs................................................................ 177General Statistics Data.............................................................................. 177Drop Policy Statistics Data......................................................................... 178LLQ Statistics Data ................................................................................... 178
Chapter 8 Command Line Interface Check Point QoS Commands........................................................................... 180Setup ........................................................................................................... 181fgate Menu ................................................................................................... 182Control ......................................................................................................... 183Monitor......................................................................................................... 185Utilities ........................................................................................................ 187
Chapter 9 Check Point QoS FAQ (Frequently Asked Questions) Questions and Answers................................................................................... 190
Introduction ............................................................................................. 190Check Point QoS Basics ............................................................................ 191Other Check Point Products - Support and Management ............................... 194Policy Creation ......................................................................................... 195Capacity Planning..................................................................................... 196Protocol Support....................................................................................... 197Installation/Backward Compatibility/Licensing/Versions................................. 198How do I? ................................................................................................ 198General Issues.......................................................................................... 199
Chapter 10 Deploying Check Point QoS Deploying Check Point QoS............................................................................. 202
Check Point QoS Topology Restrictions ....................................................... 202Sample Bandwidth Allocations ........................................................................ 204
Frame Relay Network ................................................................................ 204
Appendix A Debug Flags fw ctl debug -m FG-1 Error Codes for Check Point QoS...................................... 208
Index.......................................................................................................... 217
9
Preface PPreface
In This Chapter
Who Should Use This Guide page 10
Summary of Contents page 11
Related Documentation page 12
More Information page 15
Feedback page 16
Who Should Use This Guide
10
Who Should Use This GuideThis guide is intended for administrators responsible for maintaining network security within an enterprise, including policy management and user support.
This guide assumes a basic understanding of
• System administration.
• The underlying operating system.
• Internet protocols (IP, TCP, UDP etc.).
Summary of Contents
Preface 11
Summary of ContentsThis guide describes QoS components and contains the following chapters and appendices.
AppendicesThis guide contains the following appendices
Table A-1
Chapter Description
Chapter 1, “Overview” presents an overview of Quality of Service and how it is delivered by Check Point QoS.
Chapter 2, “Introduction to Check Point QoS”
presents an overview of QoS, including technologies and architecture.
Chapter 3, “Basic QoS Policy Management”
describes how to manage a basic FloodGate-1 QoS Policy Rule Base.
Chapter 4, “Check Point QoS Tutorial”
is a short tutorial describing how to define a QoS Policy.
Chapter 5, “Advanced QoS Policy Management”
describes the more advanced policy management features of Check Point QoS that enable you to refine basic QoS policies.
Chapter 6, “Managing Check Point QoS”
describes how to manage QoS, including modifying and changing policies and rules.
Chapter 7, “SmartView Tracker”
describes the features and tools that are available for monitoring Check Point QoS.
Chapter 8, “Command Line Interface”
discusses how to work with Check Point QoS via the Command Line.
Chapter 9, “Check Point QoS FAQ (Frequently Asked Questions)”
a compilation of frequently asked questions and their answers.
Chapter 10, “Deploying Check Point QoS”
Describes how to deploy Check Point QoS and provides sample bandwidth allocations.
Table A-2
Appendix Description
Appendix A, “Debug Flags” contains a list of debugging error codes.
Related Documentation
12
Related DocumentationThe NGX R65 release includes the following documentation
TABLE P-1 VPN-1 Power documentation suite documentation
Title Description
Internet Security Product Suite Getting Started Guide
Contains an overview of NGX R65 and step by step product installation and upgrade procedures. This document also provides information about What’s New, Licenses, Minimum hardware and software requirements, etc.
Upgrade Guide Explains all available upgrade paths for Check Point products from VPN-1/FireWall-1 NG forward. This guide is specifically geared towards upgrading to NGX R65.
SmartCenter Administration Guide
Explains SmartCenter Management solutions. This guide provides solutions for control over configuring, managing, and monitoring security deployments at the perimeter, inside the network, at all user endpoints.
Firewall and SmartDefense Administration Guide
Describes how to control and secure network access; establish network connectivity; use SmartDefense to protect against network and application level attacks; use Web Intelligence to protect web servers and applications; the integrated web security capabilities; use Content Vectoring Protocol (CVP) applications for anti-virus protection, and URL Filtering (UFP) applications for limiting access to web sites; secure VoIP traffic.
Virtual Private Networks Administration Guide
This guide describes the basic components of a VPN and provides the background for the technology that comprises the VPN infrastructure.
Related Documentation
Preface 13
Eventia Reporter Administration Guide
Explains how to monitor and audit traffic, and generate detailed or summarized reports in the format of your choice (list, vertical bar, pie chart etc.) for all events logged by Check Point VPN-1 Power, SecureClient and SmartDefense.
SecurePlatform™/ SecurePlatform Pro Administration Guide
Explains how to install and configure SecurePlatform. This guide will also teach you how to manage your SecurePlatform machine and explains Dynamic Routing (Unicast and Multicast) protocols.
Provider-1/SiteManager-1 Administration Guide
Explains the Provider-1/SiteManager-1 security management solution. This guide provides details about a three-tier, multi-policy management architecture and a host of Network Operating Center oriented features that automate time-consuming repetitive tasks common in Network Operating Center environments.
TABLE P-2 Integrity Server documentation
Title Description
Integrity Advanced Server Installation Guide
Explains how to install, configure, and maintain the Integrity Advanced Server.
Integrity Advanced Server Administrator Console Reference
Provides screen-by-screen descriptions of user interface elements, with cross-references to relevant chapters of the Administrator Guide. This document contains an overview of Administrator Console navigation, including use of the help system.
Integrity Advanced Server Administrator Guide
Explains how to managing administrators and endpoint security with Integrity Advanced Server.
Integrity Advanced Server Gateway Integration Guide
Provides information about how to integrating your Virtual Private Network gateway device with Integrity Advanced Server. This guide also contains information regarding deploying the unified SecureClient/Integrity client package.
TABLE P-1 VPN-1 Power documentation suite documentation (continued)
Title Description
Related Documentation
14
Integrity Advanced Server System Requirements
Provides information about client and server requirements.
Integrity Agent for Linux Installation and Configuration Guide
Explains how to install and configure Integrity Agent for Linux.
Integrity XML Policy Reference Guide
Provides the contents of Integrity client XML policy files.
Integrity Client Management Guide
Explains how to use of command line parameters to control Integrity client installer behavior and post-installation behavior.
TABLE P-2 Integrity Server documentation (continued)
Title Description
More Information
Preface 15
More Information• For additional technical information about Check Point products, consult Check
Point’s SecureKnowledge at https://secureknowledge.checkpoint.com/.
• See the latest version of this document in the User Center at http://www.checkpoint.com/support/technical/documents
Feedback
16
FeedbackCheck Point is engaged in a continuous effort to improve its documentation. Please help us by sending your comments to:
17
Chapter 1Overview
In This Chapter
What is Quality of Service page 18
Internet Bandwidth Management Technologies page 19
How Does Check Point Deliver QoS page 21
Features and Benefits page 23
Traditional Check Point QoS vs. Check Point QoS Express page 24
Workflow page 26
What is Quality of Service
18
What is Quality of ServiceQuality of Service is a set of intelligent network protocols and services that are used to efficiently manage the movement of information through a local or wide area networks. QoS services sort and classify flows into different traffic classes, and allocate resources to network traffic flows based on user or application ID, source or destination IP address, time of day, application specific parameters, and other user-specified variables.
Fundamentally, QoS enables you to provide better service to certain flows. This is done by either raising the priority of a flow or limiting the priority of another flow.
Internet Bandwidth Management Technologies
Chapter 1 Overview 19
Internet Bandwidth Management Technologies
In This Section
OverviewWhen you connect your network to the Internet, it is most important to make efficient use of the available bandwidth. An effective bandwidth management policy ensures that even at times of network congestion, bandwidth is allocated in accordance with enterprise priorities.
In the past, network bandwidth problems have been addressed either by adding more bandwidth (an expensive and usually short term “solution”) or by router queuing, which is ineffective for complex modern Internet protocols.
Superior QoS Solution RequirementsIn order to provide effective bandwidth management, a bandwidth management tool must track and control the flow of communication passing through, based on information derived from all communication layers and from other applications.
An effective bandwidth management tool must address all of the following issues:
• Fair Prioritization
It is not sufficient to simply prioritize communications, for example, to specify a higher priority for HTTP than for SMTP. The result may well be that all bandwidth resources are allocated to one service and none to another. A bandwidth management tool must be able to divide the available resources so that more important services are allocated more bandwidth, but all services are allocated some bandwidth.
• Minimum Bandwidth
Overview page 19
Superior QoS Solution Requirements page 19
Benefits of a Policy-Based Solution page 20
Benefits of a Policy-Based Solution
20
A bandwidth management tool must be able to guarantee a service’s minimum required bandwidth. It must also be able to allocate bandwidth preferentially, for example, to move a company’s video conference to the “head of the line” in preference to all other internet traffic.
• Classification
A bandwidth management tool must be able to accurately classify communications. However, simply examining a packet in isolation does not provide all the information needed to make an informed decision. State information — derived from past communications and other applications — is also required. A packet’s contents, the communication state and the application state (derived from other applications) must all be considered when making control decisions.
Benefits of a Policy-Based SolutionBased on the principles discussed in the previous section, there are basically three ways to improve the existing best-effort service that enterprise networks and ISPs deliver today:
• Add more bandwidth to the network.
• Prioritize network traffic at the edges of the network.
• Guarantee QoS by enforcing a set of policies that are based on business priorities (policy-based network management) throughout the network.
Of these, only policy-based network management provides a comprehensive QoS solution by:
• Using policies to determine the level of service that applications or customers need.
• Prioritizing network requests.
• Guaranteeing levels of service.
How Does Check Point Deliver QoS
Chapter 1 Overview 21
How Does Check Point Deliver QoSCheck Point QoS (previously called FloodGate-1), a policy-based QoS management solution from Check Point Software Technologies Ltd., satisfies your needs for a bandwidth management solution. Check Point QoS is a unique, software-only based application that manages traffic end-to-end across networks, by distributing enforcement throughout network hardware and software.
Check Point QoS enables you to prioritize business-critical traffic, such as ERP, database and Web services traffic, over less time-critical traffic. Check Point QoS allows you to guarantee bandwidth and control latency for streaming applications, such as Voice over IP (VoIP) and video conferencing. With highly granular controls, Check Point QoS also enables guaranteed or priority access to specific employees, even if they are remotely accessing network resources through a VPN tunnel.
Check Point QoS is deployed with VPN-1® Pro. These integrated solutions provide QoS for both VPN and unencrypted traffic to maximize the benefit of a secure, reliable, low-cost VPN network.Figure 1-1 Check Point QoS Deployment
Check Point QoS leverages the industry's most advanced traffic inspection and bandwidth control technologies. Check Point-patented Stateful Inspection technology captures and dynamically updates detailed state information on all network traffic. This state information is used to classify traffic by service or
How Does Check Point Deliver QoS
22
application. After a packet has been classified, Check Point QoS applies QoS to the packet by means of an innovative, hierarchical, Weighted Fair Queuing (WFQ) algorithm to precisely control bandwidth allocation.
Features and Benefits
Chapter 1 Overview 23
Features and BenefitsCheck Point QoS provides the following features and benefits:
• Flexible QoS policies with weights, limits and guarantees: Check Point QoS enables you to develop basic policies specific to your requirements. These basic policies can be modified at any time to incorporate any of the Advanced Check Point QoS features described in this section.
• Integration with VPN-1 Power or VPN-1 Net: Optimize network performance for VPN and unencrypted traffic: The integration of an organization’s security and bandwidth management policies enables easier policy definition and system configuration.
• Performance analysis through SmartView Tracker: monitor the performance of your system by means of log entries recorded in SmartView Tracker.
• Integrated DiffServ support: add one or more Diffserv Classes of Service to the QoS Policy Rule Base.
• Integrated Low Latency Queuing: define special classes of service for “delay sensitive” applications like voice and video to the QoS Policy Rule Base.
• Integrated Authenticated QoS: provide QoS for end-users in dynamic IP environments, such as remote access and DHCP environments.
• Integrated Citrix MetaFrame support: deliver a QoS solution for the Citrix ICA protocol.
• No need to deploy separate VPN, Firewall and QoS devices: Check Point QoS and VPN-1 Power share a similar architecture and many core technology components, therefore users can utilize the same user-defined network objects in both solutions.
• Proactive management of network costs: Check Point QoS’s monitoring systems enable you to be proactive in managing your network and thus controlling network costs.
• Support for end-to-end QoS for IP networks: Check Point QoS offers complete support for end-to-end QoS for IP networks by distributing enforcement throughout network hardware and software.
Traditional Check Point QoS vs. Check Point QoS Express
24
Traditional Check Point QoS vs. Check Point QoS Express
Both Traditional and Express modes of Check Point QoS are included in every product installation. Express mode enables you to define basic policies quickly and easily and thus “get up and running” without delay. Traditional mode incorporates the more advanced features of Check Point QoS.
You can specify whether you choose Traditional over Express or vice versa, each time you install a new policy.
Table 1-1 shows a comparative table of the features of the Traditional and Express modes of Check Point QoS.
Table 1-1 Check Point QoS Traditional Features vs. Check Point QoS Express Features
Feature Check Point
QoS
Traditional
Check Point
QoS Express
Find out more...
Weights * * “Weight” on page 45
Limits (whole rule) * * “Limits” on page 46
Guarantees (whole rule) * * “Guarantees” on page 46
Authenticated QoS * “Authenticated QoS” on page 103
Logging * * “Overview of Logging” on page 170
Accounting * *
Supported by VPN-1 UTM Edge Gateways
* Check Point VPN-1 UTM Edge Management Solutions Administration Guide
Support of platforms and HW accelerator
* *
High Availability and Load Sharing
* *
Guarantee (Per connection) * “Per Connections Guarantees” on page 90
Limit (Per connection) * “Limits” on page 46
Traditional Check Point QoS vs. Check Point QoS Express
Chapter 1 Overview 25
LLQ (controlling packet delay in Check Point QoS)
* “Low Latency Queuing” on page 95
DiffServ * “Differentiated Services (DiffServ)” on page 93
Sub-rules *
Matching by URI resources *
Matching by DNS string *
TCP Retransmission Detection Mechanism (RDED)
*
Matching Citrix ICA Applications
*
Table 1-1 Check Point QoS Traditional Features vs. Check Point QoS Express Features
Feature Check Point
QoS
Traditional
Check Point
QoS Express
Find out more...
Workflow
26
WorkflowThe following workflow shows both the basic and advanced steps that the System Administrator may follow in the installation, setup and operational procedures of Check Point QoS:Figure 1-2 Workflow Steps
1. Verify that Check Point QoS is installed on top of VPN-1Pro or VPN-1 Net.
2. Start SmartDashboard. See “Step 2: Starting SmartDashboard” on page 57.
3. Define the Global Properties of Check Point QoS. See “Defining QoS Global Properties” on page 112.
4. Define the Check Point Gateway’s Network Objects. See the SmartCenter Administration Guide.
5. Setup the basic rules and sub-rules governing the allocation of QoS flows on the network. See “Editing QoS Rule Bases” on page 118. After the basic rules have been defined, you may modify these rules to add any of the more advanced features described in step 8.
6. Implement the Rule Base. See “Implementing the Rule Base” on page 51.
7. Enable log collection and monitor the system. See “Enabling Log Collection” on page 165.
8. Modify the rules defined in step 4 by adding any of the following advanced features:
• DiffServ Markings. See “Working with Differentiated Services (DiffServ)” on page 144.
• Define Low Latency Queuing. See “Working with Low Latency Classes” on page 150.
Workflow
Chapter 1 Overview 27
• Define Authenticated QoS. See “Working with Authenticated QoS” on page 153
• Define Citrix ICA Applications. See “Managing QoS for Citrix ICA Applications” on page 155.
Workflow
28
29
Chapter 2Introduction to Check Point QoS
In This Chapter
Check Point QoS’s Innovative Technology page 30
Check Point QoS Architecture page 33
Interaction with VPN-1Pro and VPN-1 Net page 39
Check Point QoS’s Innovative Technology
30
Check Point QoS’s Innovative TechnologyFloodGate-1 is a bandwidth management solution for Internet and Intranet gateways that enables network administrators to set bandwidth policies to solve or alleviate network problems like the bandwidth congestion at network access points. The overall mix of traffic is dynamically controlled by managing bandwidth usage for entire classes of traffic, as well as individual connections. FloodGate-1 controls both inbound and outbound traffic flows.
Network traffic can be classified by Internet service, source or destination IP address, Internet resource (for example, specific URL designators), user or traffic direction (inbound or outbound). A Check Point QoS Policy consists of rules that specify the weights, limits and guarantees that are applied to the different classifications of traffic.
A rule can have multiple sub-rules, enabling an administrator to define highly granular Bandwidth Policies.
FloodGate-1 provides its real benefits when the network lines become congested. Instead of allowing all traffic to flow arbitrarily, FloodGate-1 ensures that important traffic takes precedence over less important traffic so that the enterprise can continue to function with minimum disruption, despite network congestion. FloodGate-1 ensures that an enterprise can make the most efficient use of a congested network.
FloodGate-1 is completely transparent to both users and applications.
FloodGate-1 implements four innovative technologies:
• Stateful Inspection: FloodGate-1 incorporates Check Point’s patented Stateful Inspection technology to derive complete state and context information for all network traffic.
• Intelligent Queuing Engine: This traffic information derived by the Stateful Inspection technology is used by FloodGate-1’s Intelligent Queuing Engine (IQ EngineTM) to accurately classify traffic and place it in the proper transmission queue. The network traffic is then scheduled for transmission based on the QoS Policy. The IQ Engine includes an enhanced, hierarchical Weighted Fair Queuing (WFQ) algorithm to precisely control the allocation of available bandwidth and ensure efficient line utilization.
• WFRED (Weighted Flow Random Early Drop): FloodGate-1 makes use of WFRED, a mechanism for managing packet buffers that is transparent to the user and requires no pre-configuration.
Technology Overview
Chapter 2 Introduction to Check Point QoS 31
• RDED (Retransmission Detection Early Drop): FloodGate-1 makes use of RDED, a mechanism for reducing the number of retransmits and retransmit storms. This Check Point mechanism, drastically reduces retransmit counts, greatly improving the efficiency of the enterprise’s existing lines. The increased bandwidth that FloodGate-1 makes available to important applications comes at the expense of less important (or completely unimportant) applications. As a result purchasing more bandwidth can be significantly delayed.
Technology OverviewFloodGate-1’s four innovative technologies are discussed in more detail in this section.
Stateful InspectionEmploying Stateful Inspection technology, FloodGate-1 accesses and analyzes data derived from all communication layers. This state and context data is stored and updated dynamically, providing virtual session information for tracking both connection-oriented and connectionless protocols (for example, UDP-based applications). Cumulative data from the communication and application states, network configuration and bandwidth allocation rules are used to classify communications.
Stateful Inspection enables FloodGate-1 to parse URLs and set priority levels based on file types. For example, FloodGate-1 can identify HTTP file downloads with *.exe or *.zip extensions and allocates bandwidth accordingly.
Intelligent Queuing EngineFloodGate-1 uses an enhanced WFQ algorithm to manage bandwidth allocation. A FloodGate-1 packet scheduler moves packets through a dynamically changing scheduling tree at different rates in accordance with the QoS Policy. High priority packets move through the scheduling tree more quickly than low priority packets.
Check Point QoS leverages TCP’s throttling mechanism to automatically adjust bandwidth consumption per individual connections or classes of traffic. Traffic bursts are delayed and smoothed by FloodGate-1’s packet scheduler, holding back the traffic and forcing the application to fit the traffic to the QoS Policy. By intelligently delaying traffic, the IQ Engine effectively controls the bandwidth of all IP traffic.
The preemptive IQ Engine responds immediately to changing traffic conditions and guarantees that high priority traffic always takes precedence over low priority traffic. Accurate bandwidth allocation is achieved even when there are large
Technology Overview
32
differences in the weighted priorities (for example 50:1). In addition, since packets are always available for immediate transmission, the IQ Engine provides precise bandwidth control for both inbound and outbound traffic, and ensures 100% bandwidth utilization during periods of congestion. In addition, in Traditional mode it uses per connection queuing to ensure that every connection receives its fair share of bandwidth.
WFRED (Weighted Flow Random Early Drop)WFRED is a mechanism for managing the packet buffers of FloodGate-1. WFRED does not need any preconfiguring. It adjusts automatically and dynamically to the situation and is transparent to the user.
Because the connection of a LAN to the WAN creates a bottleneck, packets that arrive from the LAN are queued before being retransmitted to the WAN. When traffic in the LAN is very intense, queues may become full and packets may be dropped arbitrarily. Dropped packets may reduce the throughput of TCP connections, and the quality of streaming media.
WFRED prevents FloodGate-1’s buffers from being filled by sensing when traffic becomes intense and dropping packets selectively. The mechanism considers every connection separately, and drops packets according to the connection characteristics and overall state of the buffer.
Unlike mechanisms such as RED/WRED, which rely on the TOS byte in the IP header (which is seldom used), WFRED queries FloodGate-1 as to the priority of the connection, and then uses this information. WFRED protects “fragile” connections from more “aggressive” ones, whether they are TCP or UDP, and always leaves some buffer space for new connections to open.
RDED (Retransmit Detect Early Drop)TCP exhibits extreme inefficiency under certain bandwidth and latency conditions. For example, the bottleneck that results from the connection of a LAN to the WAN causes TCP to retransmit packets. RDED prevents inefficiencies by detecting retransmits in TCP streams and preventing the transmission of redundant packets when multiple copies of a packet are concurrently queued on the same flow. The result is a dramatic reduction of retransmit counts and positive feedback retransmit loops. Implementing RDED requires the combination of intelligent queuing and full reconstruction of TCP streams, capabilities that exist together only in FloodGate-1.
Check Point QoS Architecture
Chapter 2 Introduction to Check Point QoS 33
Check Point QoS ArchitectureIn This Section
Basic ArchitectureThe architecture and flow control of Check Point QoS is similar to Firewall. Check Point QoS has three components:
• SmartConsole
• SmartCenter Server
• Module
The components can be installed on one machine or in a distributed configuration on a number of machines.
Bandwidth policy is created using SmartDashboard. The policy is downloaded to the SmartCenter Server where it is verified and downloaded to the QoS Modules using CPD (Check Point Daemon), which is run on the module and the SmartCenter Server. The QoS module uses the Firewall chaining mechanism (see below) to receive, process and send packets. QoS uses a proprietary classifying and rule-matching infrastructure to examine a packet. Logging information is provided using Firewall kernel API.
QoS ModuleThe major role of the QoS module is to implement a QoS policy at network access points and control the flow of inbound and outbound traffic. It includes two main parts:
• QoS kernel driver
• QoS daemon
Basic Architecture page 33
Check Point QoS Architecture page 33
Check Point QoS Configuration page 35
Basic Architecture
34
QoS Kernel Driver
The kernel driver is the heart of QoS operations. It is in the kernel driver that IP packets are examined, queued, scheduled and released, enabling QoS traffic control abilities. Utilizing Firewall kernel module services, QoS functionality is a part of the cookie chain, a Check Point infrastructure mechanism that allows modules to operate on each packet as it travels from the link layer (the machine network card driver) to the network layer (its IP stack), or vice versa.
QoS Daemon (fgd50)
The QoS daemon is a user mode process used to perform tasks that are difficult for the kernel. It currently performs 2 tasks for the kernel (using Traps):
• Resolving DNS for the kernel (used for Rule Base matching).
• Resolving Authenticated Data for an IP (using UserAuthority - again for Rule Base matching).
• In CPLS configuration, the daemon updates the kernel of any change in the cluster status. For example, if a cluster member goes down the daemon recalculates the relative loads of the modules and updates the kernel.
QoS SmartCenter ServerThe QoS SmartCenter Server is an add-on to the SmartCenter Server (fwm). The SmartCenter Server, which is controlled by Check Point SmartConsole clients, provides general services to Check Point QoS and is capable of issuing QoS functions by running QoS command line utilities. It is used to configure the bandwidth policy and control QoS modules. A single SmartCenter Server can control multiple QoS modules running either on the same machine as the SmartCenter Server or on remote machines. The SmartCenter Server also manages the Check Point Log Repository and acts as a log server for the SmartView Tracker. The SmartCenter server is a user mode process that communicates with the module using CPD.
QoS SmartConsoleThe main SmartConsole application is Check Point SmartDashboard. By creating "bandwidth rules" the SmartDashboard allows system administrators to define a network QoS policy to be enforced by Check Point QoS.
Other SmartConsole clients are the SmartView Tracker - a log entries browser; and SmartView Status which displays status information about active QoS modules and their policies.
Check Point QoS Configuration
Chapter 2 Introduction to Check Point QoS 35
Figure 2-1 Basic Architecture - Check Point QoS Components
Check Point QoS in SmartDashboardCheck Point SmartDashboard is used to create and modify the QoS Policy and define the network objects and services. If both VPN-1Pro and Check Point QoS are licensed, they each have a tab in SmartDashboard.Figure 2-2 QoS Rules in SmartDashboard
The QoS Policy rules are displayed in both the SmartDashboard Rule Base, on the right side of the window, and the QoS tree, on the left (see Figure 2-2).
Check Point QoS ConfigurationThe SmartCenter Server and the QoS Module can be installed on the same machine or on two different machines. When they are installed on different machines, the configuration is known as distributed (see Figure 2-3).
Check Point QoS Configuration
36
Figure 2-3 Distributed FloodGate-1 Configuration
Figure 2-3 shows a distributed configuration, in which one SmartCenter Server (consisting of a SmartCenter Server and a SmartConsole) controls four QoS Modules, which in turn manage bandwidth allocation on three FloodGated lines.
A single SmartCenter Server can control and monitor multiple QoS Modules. The QoS Module operates independently of the SmartCenter Server. QoS Modules can operate on additional Internet gateways and interdepartmental gateways.
Client/Server InteractionThe SmartConsole and the SmartCenter Server can be installed on the same machine or on two different machines. When they are installed on two different machines, FloodGate-1 implements the Client/Server model, in which a SmartConsole controls a SmartCenter Server running on another workstation.
Check Point QoS Configuration
Chapter 2 Introduction to Check Point QoS 37
Figure 2-4 QoS Client/Server Configuration
In the configuration depicted in Figure 2-4, the functionality of the SmartCenter Server is divided between two workstations (Tower and Bridge). The SmartCenter Server, including the database, is on Tower. The SmartConsole is on Bridge.
The user, working on Bridge, maintains the QoS Policy and database, which reside on Tower. The QoS Module on London enforces the QoS Policy on the FloodGated line.
The SmartCenter Server is started with the cpstart command, and must be running if you wish to use the SmartConsole on one of the client machines.
A SmartConsole can manage the Server (that is, run the SmartConsole to communicate with a SmartCenter Server) only if both the administrator running the SmartConsole and the machine on which the SmartConsole is running have been authorized to access the SmartCenter Server.
In practice, this means that the following conditions must be met:
• The machine on which the Client is running is listed in the$FWDIR/conf/gui-clients file.
You can add or delete SmartConsoles using the Check Point configuration application (cpconfig).
• The administrator (user) running the GUI has been defined for the SmartCenter Server.
You can add or delete administrators using the Check Point configuration application (cpconfig).
Concurrent Sessions
38
Concurrent SessionsIn order to prevent more than one administrator from modifying a QoS Policy at the same time, FloodGate-1 implements a locking mechanism. All but one open policy is ‘Read Only’.
Interaction with VPN-1Pro and VPN-1 Net
Chapter 2 Introduction to Check Point QoS 39
Interaction with VPN-1Pro and VPN-1 NetIn This Section
InteroperabilityFloodGate-1 must be installed together with VPN-1 Power or VPN-1 Net on the same system. FloodGate-1 is installed on top of a VPN-1 Power or VPN-1 Net. Because FloodGate-1 and VPN-1 Power or VPN-1 Net share a similar architecture and many core technology components, users can utilize the same user-defined network objects in both solutions. This integration of an organization’s security and bandwidth management policies enables easier policy definition and system configuration. Both products can also share state table information which provides efficient traffic inspection and enhanced product performance. FloodGate-1’s tight integration with VPN-1 Power or VPN-1 Net provides the unique ability to enable users that deploy the solutions in tandem to define bandwidth allocation rules for encrypted and network-address-translated traffic.
SmartCenter ServerIf FloodGate-1 is installed on a machine on which VPN-1 Power or VPN-1 Net is also installed, FloodGate-1 uses the VPN-1 Power or VPN-1 Net SmartCenter Server and shares the same objects database (network objects, services and resources) with VPN-1 Power or VPN-1 Net. Some types of objects have properties which are product specific. For example, a VPN-1 Power has encryption properties which are not relevant to FloodGate-1, and a FloodGate-1 network interface has speed properties which are not relevant to VPN-1 Power.
Interoperability page 39
Interoperability
40
41
Chapter 3Basic QoS Policy Management
In This Chapter
Overview page 42
Rule Base Management page 43
Implementing the Rule Base page 51
Overview
42
OverviewThis chapter describes the basic QoS policy management that is required to enable you to define and implement a working QoS Rule Base. More advanced QoS policy management features are discussed in Chapter 5, “Advanced QoS Policy Management””.
Rule Base Management
Chapter 3 Basic QoS Policy Management 43
Rule Base ManagementIn This Section
OverviewQoS policy is implemented by defining an ordered set of rules in the Rule Base. The Rule Base specifies what actions are to be taken with the data packets. It specifies the source and destination of the communication, what services can be used, and at what times, whether to log the connection and the logging level.
The Rule Base comprises the rules you create and a default rule (see Default Rule page 47). The default rule is automatically created with the Rule Base. It can be modified but cannot be deleted. The fundamental concept of the Rule Base is that unless other rules apply, the default rule is applied to all data packets. The default rule is therefore always the last rule in the Rule Base.
A very important aspect of Rule Base management is reviewing SmartView Tracker traffic logs and particular attention should be paid to this aspect of management.
Check Point QoS works by inspecting packets in a sequential manner. When Check Point QoS receives a packet belonging to a connection, it compares it against the first rule in the Rule Base, then the second, then the third, and so on. When it finds a rule that matches, it stops checking and applies that rule. If the matching rule has sub-rules the packets are then compared against the first sub-rule, then the second and so on until it finds a match. If the packet goes through all the rules or sub-rules without finding a match, then the default rule or default sub-rule is applied. It is important to understand that the first rule that matches is applied to the packet, not the rule that best matches.
Overview page 43
Connection Classification page 44
Services and Resources page 45
Time Objects page 45
Bandwidth Allocation and Rules page 45
Default Rule page 47
QoS Action Properties page 47
Example of a Rule Matching VPN Traffic page 48
Bandwidth Allocation and Sub-Rules page 49
Connection Classification
44
After you have defined your network objects, services and resources, you can use them in building a Rule Base. For installation instructions and instructions on building a Rule Base, see “Editing QoS Rule Bases” on page 118.
The QoS Policy Rule Base concept is similar to the Security Policy Rule Base. General information about Policy Rule Bases can be found in the SmartCenter Administration Guide.Figure 3-1 SmartDashboard Rule Base Window
Connection ClassificationA connection is classified according to four criteria:
• Source: A set of network objects, including specific computers, entire networks, user groups or domains.
• Destination: A set of network objects, including specific computers, entire networks or domains.
• Service: A set of IP services, TCP, UDP, ICMP or URLs.
• Time: Specified days or time periods.
Network ObjectsNetwork objects serve as the sources and destinations that are defined in QoS Policy rules. The network objects that can be used in FloodGate-1 rules include workstations, networks, domains, and groups.
Note - It is best to organize lists of objects (network objects and services) in groups rather than in long lists. Using groups gives you a better overview of your QoS Policy and leads to a more readable Rule Base. In addition, objects added to groups are automatically included in the rules.
Services and Resources
Chapter 3 Basic QoS Policy Management 45
Information about network objects can be found in the SmartCenter Administration Guide.
User GroupsCheck Point QoS allows you to define User Groups that are comprised of predefined users. For example, all the users in the marketing department can be grouped together in a User Group called Marketing. when defining a Source in a rule you can then use this group as a possible Source, instead of adding individual users to the Source of the rule.
Services and ResourcesFloodGate-1 allows you to define QoS rules, not only based on the source and destination of each communication, but also according to the service requested. The services that can be used in FloodGate-1 rules include TCP, Compound TCP, UDP, ICMP and Citrix TCP services, IP services
Resources can also be used in a FloodGate-1 Rule Base. They must be of type URI for QoS.
Time ObjectsCheck Point QoS allows you to define Time objects that are used is defining the time that a rule is operational. Time objects can be defined for specific times and/or for specific days. The days can further be divided into days of the month or specific days of the week.
Bandwidth Allocation and RulesA rule can specify three factors to be applied to bandwidth allocation for classified connections:
WeightWeight is the relative portion of the available bandwidth that is allocated to a rule.
To calculate what portion of the bandwidth the connections matched to a rule receive, use the following formula:
this rule’s portion = this rule’s weight / total weight of all rules with open connections
Bandwidth Allocation and Rules
46
For example, if this rule’s weight is 12 and the total weight of all the rules under which connections are currently open is 120, then all the connections open under this rule are allocated 12/120 (or 10%) of the available bandwidth.
In practice, a rule may get more than the bandwidth allocated by this formula, if other rules are not using their maximum allocated bandwidth.
Unless a per connection limit or guarantee is defined for a rule, all connections under a rule receive equal weight.
Allocating bandwidth according to weights ensures full utilization of the line even if a specific class is not using all of its bandwidth. In such a case, the left over bandwidth is divided among the remaining classes in accordance with their relative weights. Units are configurable, see “Defining QoS Global Properties” on page 112.
GuaranteesA guarantee allocates a minimum bandwidth to the connections matched with a rule.
Guarantees can be defined for:
• the sum of all connections within a rule
A total rule guarantee reserves a minimum bandwidth for all the connections under a rule combined. The actual bandwidth allocated to each connection depends on the number of open connections that match the rule. The total bandwidth allocated to the rule can be no less than the guarantee, but the more connections that are open, the less bandwidth each one receives.
• individual connections within a rule
A per connection guarantee means that each connection that matches the particular rule is guaranteed a minimum bandwidth.
Although weights do in fact guarantee the bandwidth share for specific connections, only a guarantee allows you to specify an absolute bandwidth value.
LimitsA limit specifies the maximum bandwidth that is assigned to all the connections together. A limit defines a point beyond which connections under a rule are not allocated bandwidth, even if there is unused bandwidth available.
Limits can also be defined for the sum of all connections within a rule or for individual connections within a rule.
Default Rule
Chapter 3 Basic QoS Policy Management 47
For more information on weights, guarantees and limits, see “Action Type” on page 47.
Default RuleA default rule is automatically added to each QoS Policy Rule Base, and assigned the weight specified in the QoS (FloodGate-1) page of the Global Properties window. You can modify the weight, but you cannot delete the default rule (see “Weight” on page 45).
The default rule applies to all connections not matched by the other rules or sub-rules in the Rule Base.
In addition, a default rule is automatically added to each group of sub-rules, and applies to connections not classified by the other sub-rules in the group (see “To Verify and View the QoS Policy” on page 51).
QoS Action PropertiesIn the QoS Action Properties window you can define bandwidth allocation properties, limits and guarantees for a rule.
Action TypeBy this stage, you should already have decided whether your policy is Traditional mode or Express mode, see “Traditional Check Point QoS vs. Check Point QoS Express” on page 24.
You can select one of the following Action Types:
• Simple
• Advanced
Note - Bandwidth allocation is not fixed. As connections are opened and closed, FloodGate-1 continuously changes the bandwidth allocation to accommodate competing connections, in accordance with the QoS Policy.
Example of a Rule Matching VPN Traffic
48
Table 3-1 shows which Action Types you can select in Traditional or Express modes.
Simple
The following actions are available:
• Apply rule to encrypted traffic only
• Rule weight
• Rule limit
• Rule guarantee
Advanced
The same actions that are available in Simple mode are available in Advanced mode with the addition of the following:
• Per connection limit
• Per rule guarantee
• Per connection guarantee
• Number of permanent connections
• Accept additional connections
Example of a Rule Matching VPN TrafficVPN traffic is traffic that is encrypted in the same gateway by Check Point VPN. VPN traffic does not refer to traffic that was encrypted by a non-Check Point product prior to arriving at this gateway. This type of traffic can be matched using the IPSec service.
When Apply rule only to encrypted traffic is checked in the QoS Action Properties window, only VPN traffic is matched to the rule. If this field is not checked, all types of traffic (both VPN and non-VPN) are matched to the rule.
Table 3-1 Action Types Available
Action Type Traditional Mode Express Mode
Simple Yes Yes
Advanced Yes No
Bandwidth Allocation and Sub-Rules
Chapter 3 Basic QoS Policy Management 49
Use the Apply rule only to encrypted traffic field to build a Rule Base in which you define QoS actions for VPN traffic which are different than the actions that are applied to non-VPN traffic. Since Check Point QoS uses the First Rule Match concept, the VPN traffic rules should be defined as the top rules in the Rule Base. Below them rules which apply to all types of traffic should be defined. Other types of traffic skip the top rules and match to one of the non-VPN rules defined below the VPN traffic rules. In order to completely separate VPN traffic from non-VPN traffic, define the following rule at the top of the QoS Rule Base:
All the VPN traffic is matched to this rule. The rules following this VPN Traffic Rule are then matched only by non-VPN traffic. You can define sub-rules below the VPN Traffic rule that classify the VPN traffic more granularly.
Bandwidth Allocation and Sub-RulesWhen a connection is matched to a rule with sub-rules, a further match is sought among the sub-rules. If none of the sub-rules apply, the default rule for the specific group of sub-rules is applied (see “Default Rule” on page 47).
Sub-rules can be nested, meaning that sub-rules themselves can have sub-rules. The same rules then apply to the nested sub-rules. If the connection matches a sub-rule that has sub-rules itself, a further match is sought among the nested sub-rules. Again if none of the sub-rules apply, the default rule for the specific group of sub-rules is applied.
Bandwidth is allocated on a top/down approach. This means that sub-rules cannot allocate more bandwidth to a matching rule, than the rule in which the sub-rule is located. A nested sub-rule, therefore, cannot allocate more bandwidth than the sub-rule in which it is located.
A Rule Guarantee must likewise always be greater than or equal to the Rule Guarantee of any sub-rule within that rule. The same applies to Rule Guarantees in sub-rules and their nested sub-rules., as shown in the following example.
Table 3-2 VPN Traffic Rule
Name Source Dest Service Action
VPN rule Any Any Any VPN Encrypt, and other configured actions
Bandwidth Allocation and Sub-Rules
50
Example:
In this example any extra bandwidth from the application of Rule A1.1 is applied to Rule A2 before it is applied to Rule A1.2.
Table 3-3 Bandwidth Allocation in Nested Sub-Rules
Rule Name Source Destination Service Action
Rule A Any Any ftp Rule Guarantee - 100KBpsWeight 10
Start of Sub-Rule A
Rule A1 Client-1 Any ftp Rule Guarantee - 100KBpsWeight 10
Start of Sub-Rule A1
Rule A1.1 Any Any ftp Rule Guarantee - 80KBpsWeight 10
Rule A1.2 Any Any ftp Weight 10
End of
Sub-Rule A1
Rule A2 Client-2 Any ftp Weight 10
End of
Sub-Rule A
Rule B Any Any http Weight 30
Implementing the Rule Base
Chapter 3 Basic QoS Policy Management 51
Implementing the Rule BaseWhen you have defined the desired rules, you should perform a heuristic check on the Rule Base to check that the rules are consistent. If a Rule Base fails the verification, an appropriate message is displayed.
You must save the Policy Package before verifying. Otherwise, changes made since the last save will not be checked.
After verifying the correctness of the Rule Base, it must be installed on the FloodGate-1 Modules that will enforce it. When you install a QoS Policy, the policy is downloaded to these QoS Modules. There must be a QoS Module running on the object which receives the QoS Policy.
In This Section
To Verify and View the QoS Policy1. Select Policy>Verify to perform a heuristic check on the Rule Base to check
that the rules are consistent.
2. Select Policy>View to view the generated rules as ASCII text.
To Install and Enforce the PolicyPerform the following steps in order to install and enforce the QoS policy:
1. Once the rule base is complete, select Install from the Policy menu. The Install Policy window is displayed. Specify the QoS modules on which you would like to install your new QoS policy. By default, all QoS modules are already selected. (In order for an object to be a QoS module, it needs to have FloodGate-1 checked under Check Point Products in the Object Properties window).
Note - The QoS Module machine and the SmartCenter module machine must be properly configured before a QoS Policy can be installed.
To Verify and View the QoS Policy page 51
To Install and Enforce the Policy page 51
To Uninstall the QoS Policy page 52
To Monitor the QoS Policy page 52
To Uninstall the QoS Policy
52
The objects in the list are those that have FloodGate-1 Installed checked in their definition (see “Specifying Interface QoS Properties” on page 114).
You may deselect and reselect specific items, if you wish. The QoS Policy is not installed on unselected items.
2. Click OK to install the QoS Policy on all selected hosts. The installation progress window is displayed.
To Uninstall the QoS PolicyYou can uninstall QoS Policy from any or all of the QoS Modules in which it is installed.
1. Choose Uninstall from the Policy menu to remove the QoS Policy from the selected QoS Module. The Install Policy window is displayed.
2. Deselect those QoS Modules from which you would like to uninstall the QoS policy.
3. Click OK.
To Monitor the QoS PolicyCheck Point SmartView Monitor allows you to monitor traffic through a floodgated interface. For more information, see SmartView Monitor Administration Guide.
53
Chapter 4Check Point QoS Tutorial
In This Chapter
Introduction page 54
Building and Installing a QoS Policy page 56
Conclusion page 84
Introduction
54
IntroductionThis chapter presents a step by step guide to building and installing a QoS Policy in Check Point QoS. This tutorial is based on the network configuration shown in Figure 4-1 on page 54.
This tutorial is based on a simple network configuration, but working through it will familiarize you with the many issues involved in building and installing a FloodGate-1 QoS Policy. Each step in the process is described in detail so that by the end of this tutorial you will have developed a practical knowledge of building and installing a usable QoS policy.
The tutorial walks you through the steps involved in physically installing a network, and then introduces you to SmartDashboard and Check Point QoS, in which you configure the network and implement QoS policy.Figure 4-1 Example Network Configuration
This example shows a typical network configuration for an organization with offices located in London, Oxford and Cambridge. The Check Point QoS Module is located in London where the gateway to the Internet will comprise 3 interfaces. The SmartCenter Server is located at Oxford while the SmartConsole is installed at Cambridge. Within the private local network there are the Marketing and
Introduction
Chapter 4 Check Point QoS Tutorial 55
Engineering departments. In this tutorial you are shown how a QoS policy is implemented to regulate and optimize the flow in Internet traffic to these departments.
Building and Installing a QoS Policy
56
Building and Installing a QoS PolicyThe following steps represent the workflow that must be followed in order to build and install a QoS Policy on the network shown in Figure 4-1. Each of these steps is then described in detail in the sections that follow:
1. Install the appropriate Check Point Modules on each machine, as needed (see Table 4-1).
2. Start SmartDashboard and display the QoS tab.
3. Determine the type of QoS Policy you want to implement.
4. Define the network objects to be used in the Rule Base.
You define only those objects that are explicitly used in the Rule Base and do not have to define the entire network.
5. Define any proprietary services used in your network.
You do not have to define the commonly used services. These are already defined for you in FloodGate-1. In most cases, you need only specify a name, for network objects and services because Check Point QoS obtains the object’s properties from the appropriate databases (DNS, YP. hosts file).
6. Create a new QoS Rule Base and the rules that comprise that Rule Base.
7. Install the Rule Base on the QoS Module machine, which will enforce the QoS Policy.
Each of these steps are described in detail in the sections that follow.
Table 4-1 Check Point Modules to Install on Each Machine
Computer Function Check Point Module to install
London QoS Module; the Gateway to the Internet
QoS ModuleVPN-1 Power Module (required)
Oxford SmartCenter Server SmartCenter Server, QoS Add-on
Cambridge SmartConsole SmartDashboard
Note - In order to manage QoS modules, you need to install Check Point QoS on the SmartCenter Server as well as on the module.
Step 1: Installing Check Point Modules
Chapter 4 Check Point QoS Tutorial 57
In This Section
Step 1: Installing Check Point ModulesThis step describes the physical installation of the Check Point Products at the various locations in the example on page 54. In this tutorial you do not physically install the network but you do run the QoS Module on SmartDashboard.
Detailed installation instructions are available in the Getting Started Guide.
Install QoS in the following sequence:
1. Install QoS and VPN-1 Power or VPN-1 Net modules on London.
2. Install SmartConsole on Cambridge.
3. Install SmartCenter Server on Oxford.
4. On Oxford, define Cambridge as a SmartConsole.
5. On Oxford, define the administrators who will be allowed to manage the QoS Policy.
6. Establish a secure connection (SIC) between the SmartCenter Server at Oxford and the QoS Module at London.
Step 2: Starting SmartDashboardYou must start SmartDashboard in order to be able to access Check Point QoS. For the purposes of this tutorial, and although all the regular log on procedures are described in this section, you must run SmartDashboard in Demo Mode, selecting the Advanced option. This section describes how to start SmartDashboard and access its QoS tab to be able to enter and install the QoS Policy you are defining.
Step 1: Installing Check Point Modules page 57
Step 2: Starting SmartDashboard page 57
Step 3: Determining QoS Policy page 61
Step 4: Defining the Network Objects page 61
Step 5: Defining the Services page 73
Step 6: Creating a Rule Base page 73
Step 7: Installing a QoS Policy page 82
To Start SmartDashboard
58
To Start SmartDashboard1. From the Start menu, select Programs > Check Point SmartConsole R65 >
SmartDashboard. The Welcome to Check Point SmartDashboard window (Figure 4-2) is displayed:
Figure 4-2 SmartDashboard Login Window
2. You can log in using either your:
• User Name and Password
1. Select User Name.
2. Enter your user name and password in the designated field.
• Certificate
1. Select Certificate.
2. Select the name of your certificate file from the dropdown list.
3. You can browse for the file using by clicking .
4. Enter the password you used to create the certificate in the Password field.
3. Enter the name of the machine on which the SmartCenter Server is running. You can enter one of the following:
• A resolvable machine name
• A dotted IP address
To Start SmartDashboard
Chapter 4 Check Point QoS Tutorial 59
4. To work in local mode, check Demo Mode and select Advanced from the drop-down list.
5. (Optional) Check Read Only if you do not wish to modify a policy,
6. (Optional) Click More Options >> to display the Certificate Management and Advanced Options (Figure 4-3).
Figure 4-3 (SmartDashboard Login Window - More Options
7. (Optional) Click Change Password to change the certificate password.
8. (Optional) Check Use compressed connection to compress the connection to the SmartCenter Server.
To Start SmartDashboard
60
9. (Optional) Enter the text describing why the administrator wants to make a change in the security policy in the Session Description field. The text appears as a log entry in the SmartView Tracker in the Session Description column (in Audit mode only).
10. (Optional) Check Do not save recent connections information if you do not want your connection settings saved.
11. Click Less Options << to hide the Certificate Management and Advanced options.
12. Click OK The SmartDashboard main window Figure 4-4 is displayed:Figure 4-4 SmartDashboard Main Window.
13. Click the QoS tab display the QoS Rule Base. The QoS tab (Figure 4-5) is displayed.
Note - If the Session Description column does not appear in the SmartView Tracker, use the Query Properties pane to display it. For more information on the SmartView Tracker, see the chapter called SmartView Tracker in the SmartCenter Administration Guide.
Step 3: Determining QoS Policy
Chapter 4 Check Point QoS Tutorial 61
Figure 4-5 QoS Tab
Step 3: Determining QoS PolicyTo implement an effective QoS Policy, you must first determine how you currently use your network, and then identify and prioritize the types of traffic and the users who are going to use the network.
For example, a typical QoS Policy would be:
• HTTP traffic should be allocated more bandwidth than RealAudio.
• Marketing should be allocated more bandwidth than Engineering.
You will create the rules to implement this policy in “Step 6: Creating a Rule Base” on page 73.
Step 4: Defining the Network ObjectsYou must now define the Network Objects including London, the gateway on which the QoS Module is running, and its interfaces, as well as the sub-networks for the Marketing and Engineering departments.
This step describes, as an example, how the gateway London will be defined.
To Define the Gateway London
62
To Define the Gateway London1. Using one of the methods described in Table 4-2, open the Properties window
To Define the Gateway London
Chapter 4 Check Point QoS Tutorial 63
(Figure 4-8 on page 66.)
Table 4-2 Creating a New Gateway
From the... ... proceed as follows
Manage menu • From the Manage menu, choose Network Objects. The Network Objects window (Figure 4-6) is displayed.
Figure 4-6 Network Objects Window
• Click New and choose Check Point > Gateway from the menu. The Check Point Gateway - General
Properties window is displayed (Figure 4-7).
Objects toolbar • If the Objects toolbar is not visible, then, from the View menu choose Toolbars > Objects.to display it.
• Select from the toolbar. The Network Objects window (Figure 4-6) is displayed.
• Click New and choose Check Point > Gateway from the menu. The Check Point Gateway - General
Properties window is displayed (Figure 4-7).
Network Objects tree • Right-click Network Objects in the Network Objects tree and choose New > Check Point > Gateway from the menu. The Check Point Gateway - General
Properties window is displayed (Figure 4-7).
To Define the Gateway London
64
Figure 4-7 Check Point Gateway - General Properties Window
2. In the Check Point Gateway - General Properties window (Figure 4-7) enter the information shown in Table 4-3 to define London’s gateway.
Table 4-3 London’s Check Point Gateway - General Properties Window
Field Value Explanation
Name London This is the name by which the object is known on the network; the response to the hostname command.
IP Address 192.32.32.32 This is the interface associated with the host name in the DNS — get this by clicking Get Address.For gateways, this should always be the IP address of the external interface.
To Define the Gateway London
Chapter 4 Check Point QoS Tutorial 65
The Check Point Gateway - General Properties window now has the information shown in Figure 4-8 on page 66.
Comment QoS Module (gateway)
This is the text that is displayed at the bottom of the Network Objects window when this object is selected
Check Point
Products • Select the
Version from the drop-down list.
• Check VPN-1 Power (if needed), FireWall-1and QoS (FloodGate-1).
These settings specify the Check Point products installed on London, and their version number.Check Point QoS must be installed on any gateway on which a QoS Module is installed.Note that if multiple Check Point products are installed on a machine, they must all be the same version number.
Secure Internal Communication
Establishes a secure communication channel between Check Point Modules.
Table 4-3 London’s Check Point Gateway - General Properties Window
Field Value Explanation
To Define the Interfaces on Gateway London
66
Figure 4-8 Check Point Gateway - General Properties Window
To Define the Interfaces on Gateway London1. Click Topology in the tree on the left side of the Check Point Gateway -London
window. The Topology page Check Point Gateway - London window (Figure 4-9) is displayed.
To Define the Interfaces on Gateway London
Chapter 4 Check Point QoS Tutorial 67
Figure 4-9 Check Point Gateway - London Topology Window
2. The easiest and most reliable way to define the interfaces is to click Get.., which automatically retrieves general and topology information for each interface. If you choose this method of configuring the gateway, the topology fetched suggests the external interface of the gateway based on the QoS Module routing table. You must ensure that this information is correct.
Alternatively, click Add. The Interface Properties window (Figure 4-10) is displayed.
To Define the Interfaces on Gateway London
68
Figure 4-10 Interface Properties - General Tab
3. Enter the information on the three interfaces listed in Table 4-4, Table 4-5 and Table 4-6 in the General and Topology tabs of this window.
4. Click OK after you have entered the information from each table to add the interface to the Check Point Gateway - London - Topology window.
To Define the Interfaces on Gateway London
Chapter 4 Check Point QoS Tutorial 69
The data for each of the three interfaces of London is as follows:
Table 4-4 Field Values — Interface Properties Window — le0
Field Value Explanation
General tab
Name le0
Net Address 192.32.32.32
Net Mask 255.255.255.0
Topology tab
Topology Check External (leads out to the Internet).
Specifies to which network this interface leads.
Anti-Spoofing Check Perform Anti-Spoofing based on network topology.
Specifies that each incoming packet will be examined to ensure that its source IP address is consistent with the interface through which it entered the machine.
Spoof Tracking Check Log. Specifies that when spoofing is detected, the event will be logged.
To Define the Interfaces on Gateway London
70
Table 4-5 Field Values — Interface Properties Window — le1
Field Value Explanation
General tab
Name le1
Net Address 192.32.42.32
Net Mask 255.255.255.0
Topology tab
Topology Check Internal (leads to the local network).
Specifies to which network this interface leads.
IP addresses behind this interface
Check Network defined by the interface IP and Net Mask.
Specifies that the standard IP addressing scheme is being used.
Anti-Spoofing Check Perform Anti-Spoofing based on network topology.
Specifies that each incoming packet will be examined to ensure that its source IP address is consistent with the interface through which it entered the machine.
Spoof Tracking Check Log. Specifies that when spoofing is detected, the event will be logged.
To Define the Interfaces on Gateway London
Chapter 4 Check Point QoS Tutorial 71
After the three interfaces have been defined, they are listed in the Check Point Gateway - London - Topology window (Figure 4-11).
Table 4-6 Field Values — Interface Properties Window — le2
Field Value Explanation
General tab
Name le2
Net Address 199.199.199.32
Net Mask 255.255.255.0
Topology tab
Topology Check Internal (leads to the local network).
Specifies to which network this interface leads.
IP addresses behind this interface
Check Network defined by the interface IP and Net Mask.
Specifies that the standard IP addressing scheme is being used.
Anti-Spoofing Check Perform Anti-Spoofing based on network topology.
Specifies that each incoming packet will be examined to ensure that its source IP address is consistent with the interface through which it entered the machine.
Spoof Tracking Check Log. This specifies that when spoofing is detected, the event will be logged.
To Define the QoS Properties for the Interfaces on Gateway London
72
Figure 4-11 Check Point Gateway - Topology Page
To Define the QoS Properties for the Interfaces on Gateway London
1. In the Check Point Gateway - London - Topology window (Figure 4-11), double-click London’s external interface (le0), or select it and click Edit. The Interface Properties window is displayed.
2. Click the QoS tab. The Interface Properties - QoS tab (Figure 4-12) is displayed.
Step 5: Defining the Services
Chapter 4 Check Point QoS Tutorial 73
Figure 4-12 Interface Properties Window - QoS tab
3. Check both Inbound Active and Outbound Active.
4. From the Rate dropdown list set both rates to 192000 - T1 (1.5 Mbps).
5. Click OK to exit the Interface Properties window.
6. Click OK to exit the Check Point Gateway - London - Topology window.
Step 5: Defining the ServicesThe QoS Policy required for this tutorial does not require the definition of new proprietary services. The commonly used services HTTP and RealAudio are already defined in FloodGate-1.
Step 6: Creating a Rule BaseAfter defining your network objects and services, you are now ready to create the Rule Base that will comprise your QoS policy rules. When you start SmartDashboard, the last Policy Package that was used is displayed. The Policy Package comprises the Rule Bases of all the tabs that are displayed in the SmartDashboard window. This tutorial is only concerned with the QoS Rule Base
To Create a New Policy Package
74
which is accessed when you select the QoS tab. In this step you close this Policy Package and create a new Policy Package in which you have the QoS Rule Base for the rules that you are about to create.
The new Rule Base is created with a Default Rule (see “Default Rule” on page 47). After you have created the Rule Base you must add the rules that will enforce the QoS Policy determined in “Step 3: Determining QoS Policy” on page 61.
To Create a New Policy Package1. In SmartDashboard select New from the File menu. The Save window is displayed
requesting that you save the displayed Policy Package before creating a new one.
2. Click Save and continue. The New Policy Package window is displayedFigure 4-13 New Policy Package Window
3. Enter the name in the New policy Package Name field.
4. Check Security and Address Translation (if needed).
5. Check QoS. and select Traditional mode.
6. Click OK. The new Policy Package is created together with a Default Rule and is displayed in the QoS tab (Figure 4-14).
Figure 4-14 New Rule Base In the QoS Tab
To Create a New Rules
Chapter 4 Check Point QoS Tutorial 75
To Create a New RulesThis procedure describes how to create the two new rules required to enforce the Rule Base. Create two rules: Web Rule and RealAudio Rule.
1. Click the QoS tab to access the QoS Rule Base.
2. Right-click in the Name field of the QoS tab and select Add Rule above from the menu that is displayed. The Rule Name window is displayed.
Figure 4-15 Rule Name Window
3. Enter Web Rule as the Rule Name.
4. Click OK. The rule is added to the Rule Base.
5. Repeat steps 1 to 3 and create a new rule with the name of RealAudio Rule. The QoS tab in SmartDashboard lists all the rules in the Rule Base.
Figure 4-16 QoS Tab with Rules
Rule PropertiesWhen a new rule is created it has the default values assigned by the System Administrator. You must change these values so that they correctly reflect the policies you want.
To Modify New Rules
76
The next procedure describes how to change these rules so that they reflect the values shown in Table 4-7.
To Modify New Rules1. In the QoS tab, right-click in the Service field of the Web Rule and select Add
from the menu that is displayed. The Add Object window (Figure 4-17) is displayed.
Figure 4-17 Add Object Window
2. Select HTTP from the list.
3. Click OK. The Web Rule’s Service is changed.
4. Repeat steps 1 to 3 but change the service of the RealAudio rule to RealAudio.
5. Right-click in the Action field of the Web Rule and select Edit Properties from the menu that is displayed. The QoS Action Properties window (Figure 4-18) is displayed.
Table 4-7 Changing Rules Default Values
Rule Name Source Destination Service Action
Web Rule Any Any HTTP Weight 35
RealAudio Rule
Any Any RealAudio Weight 5
Default Any Any Any Weight 10
To Modify New Rules
Chapter 4 Check Point QoS Tutorial 77
Figure 4-18 QoS Action Properties Window
6. Change the Rule Weight to 35 and Click OK.
7. Repeat steps 5 and 6 and change the weight of the RealAudio Rule to 5.
Classifying Traffic by ServiceEven an exhaustive Rule Base will generally not explicitly define rules for all the “background” services (such as DNS and ARP) in the traffic mix, but will let the Default rule deal with them.Figure 4-19 Service Rules in the GUI
Note how the structure of the Rule Base is shown at the left of the window (Figure 4-19) as a tree, with the Default Rule highlighted in both the tree and the Rule Base. (For a description of the Rule Base window, see Chapter 3, “Basic QoS Policy Management”.”).
To Modify New Rules
78
The effect of these rules is that, when connections compete for bandwidth, they receive bandwidth in accordance with the weights assigned by the rules that apply to them. For example, Table 4-8 describes what happens when there are four active connections.
It is important to note that the bandwidth allocation is constantly changing. Bandwidth is allocated among connections according to their relative weight. As the connection mix changes — as it does continuously as connections are opened and closed — FloodGate-1 changes the bandwidth allocation in accordance with the QoS Policy, so that bandwidth is never wasted. For example, if the HTTP, FTP and TELNET connections are all closed, and the only remaining connection is the RealAudio connection, RealAudio will receive 100% of the bandwidth.
Suppose now that the TELNET and FTP connections are closed. Table 4-9 shows the result.
Both HTTP and RealAudio benefit from the bandwidth released by the closed connections. Even though RealAudio is assigned a very small weight compared to HTTP, it will never “starve,” even in the event of heavy HTTP traffic.
Table 4-8 Service Rules - four active Connections
connections relevant rule bandwidth remarks
HTTP Web Rule 70% 35 / 50 (the total weights)
RealAudio RealAudio Rule
10% 5 / 50
FTP Default sharing 20%
10 /50; a rule applies to all the connections together
TELNET Default sharing 20%
10 /50; a rule applies to all the connections together
Table 4-9 Service Rules - two active Connections
connections relevant rule bandwidth remarks
HTTP Web Rule 87.5% 35/40 (the total weights)
RealAudio RealAudio Rule
12.5% 5/40
Note - In practice, you will probably want to give a high relative weight to an interactive service such as TELNET, which transfers small amounts of data but has an impatient user at the keyboard.
To Modify New Rules
Chapter 4 Check Point QoS Tutorial 79
Classifying Traffic by SourceThe second part of the QoS Policy (“Marketing should be allocated more bandwidth than Engineering.””) can be expressed in the following rules:
Using the same principles described in “To Create a New Rules” on page 75 and “To Modify New Rules” on page 76, create new rules and modify them to reflect the values shown in Table 4-10. The effect of these rules is similar to the effect of the rules in Table 4-8 on page 78, except for:
• the different weights
• the fact that allocation is based on source rather than on services.
Classifying Traffic by Service and SourceTable 4-11 shows all the rules together in a single Rule Base.
Table 4-10 Marketing is Allocated More Bandwidth Than Engineering
Rule Name Source Destination Service Action
Marketing Rule
Marketing Any Any Weight 30
Engineering Rule
Engineering
Any Any Weight 20
Default Any Any Any Weight 10
Table 4-11 All the Rules Together
Rule Name Source Destination Service Action
Web Rule Any Any HTTP Weight 35
RealAudio Rule
Any Any RealAudio Weight 5
Marketing Rule
Marketing Any Any Weight 30
Engineering Rule
Engineering
Any Any Weight 20
Default Any Any Any Weight 10
To Modify New Rules
80
In this Rule Base, bandwidth allocation is based both on sub-networks and on services.
First Rule Match PrincipleIn the Rule Base in Table 4-11, it is possible that more than one rule can be relevant to a connection. However, FloodGate-1 works according to a first rule match principle. Every connection is examined against the QoS Policy and receives bandwidth according to the action defined in the first rule that is matched.
If a user in Marketing initiates an HTTP connection, both Web Rule and Marketing Rule are theoretically relevant. Because Web Rule comes before Marketing Rule in the Rule Base, the connection will be given a weight of 35. Marketing Rule will no longer be relevant to this connection.
In order to differentiate HTTP traffic by source, it would be necessary to create sub-rules for Web Rule. See “Sub-Rules” on page 81.
Guarantees and LimitsIn addition to using weights, you can define bandwidth allocation by using guarantees and limits. You can define guarantees and limits for whole rules, or for individual connections within a rule.
For example, the Web Rule shown in the Rule Base in Table 4-11 on page 79 allocates 35% of available bandwidth to all the HTTP connections combined. The actual amount of bandwidth received by connections under this rule depends on available bandwidth and on the open connections that match the other rules.
A guarantee can be used mainly to specify bandwidth in absolute measures (such as bits or bytes) instead of relative weights. Note however that 35% of available bandwidth (specified in the example above) is assured to you. You may get more bandwidth if there are few connections backlogged to other rules, but you will not get less bandwidth. The bandwidth allocated is absolutely guaranteed. In Table 4-12, Web Rule is guaranteed 20 KBps. The connections under Web Rule will receive a total bandwidth of 20 KBps. Any remaining bandwidth will be allocated to all the rules, Web Rule included, according to their weights.
Note - The actual bandwidth allocated to a connection at any given moment depends on the weights of the other connections that are active at the same time.
To Modify New Rules
Chapter 4 Check Point QoS Tutorial 81
For more information and examples of guarantees and limits, see “Examples: Guarantees and Limits” on page 87 and “Bandwidth Allocation and Rules” on page 45.
Sub-RulesSub-rules are rules within a rule. For example, you may wish to allocate bandwidth for HTTP connections by source, so that HTTP connections from Marketing receive more bandwidth than other HTTP traffic. In this case, you would define sub-rules under Web Rule as follows:
Table 4-12 Guarantee Example
Rule Name Source Destination Service Action
Web Rule Any Any HTTP Guarantee 20 KBpsWeight 35
RealAudio Rule
Any Any RealAudio Weight 5
Marketing Rule
Marketing Any Any Weight 30
Engineering Rule
Engineering
Any Any Weight 20
Default Any Any Any Weight 10
Table 4-13 Defining Sub-Rules
Rule Name Source Destination Service Action
Web Rule Any Any HTTP Weight 20
Start of Sub-Rule
Marketing HTTP Marketing Any Any Weight 10
Default Any Any Any Weight 1
End of Sub-Rule
Step 7: Installing a QoS Policy
82
Sub-Rules are created in a similar manner to Rules as described in “To Create a New Rules” on page 75, However to create a sub-rule you right-click in the Name field of the rule in which you want to create the sub-rule and select Add Sub-Rule from the menu that is displayed.
The sub-rule means that for connections under Web Rule bandwidth should be allocated according to the weights specified: 10 for HTTP traffic from the Marketing department and 1 for everything else.
The bandwidth allocated to the Web Rule according to its weight (20). This weight is further divided between its sub-rules in a 10:1 ratio. Note that there will be two Default rules: one for the Rule Base as a whole and another for the sub-rules of Web Rule.
The Source, Destination and Service fields of the sub-rule must always be a “sub-set” of the parent rule otherwise the sub-rule will be ineffective.
Step 7: Installing a QoS PolicyAfter you have defined the Rule Base, you can install the QoS Policy on the QoS Modules by selecting Install from the Policy menu.
The Install Policy window (Figure 4-20) is displayed, showing a list of gateways defined as FloodGate-1 Modules (see “Step 4: Defining the Network Objects” on page 61).Figure 4-20 Install Policy Window
Step 7: Installing a QoS Policy
Chapter 4 Check Point QoS Tutorial 83
Select the specific QoS Modules on which to install the QoS Policy. Check Point QoS will enforce the QoS Policy on the directions specified in the interface properties of each selected module. and click OK
For further information, see “Implementing the Rule Base” on page 51.
Conclusion
84
ConclusionYou have now completed all the steps that were required to install the network described in Figure 4-1 on page 54, and to define the Rule Base that will implement the required policy QoS policy.
As a result, you should have a much better understanding of how QoS policy can be implemented using Check Point QoS. It is strongly recommended however that you now spend some time and refer to Chapter 6, “Managing Check Point QoS”” for further information.
85
Chapter 5Advanced QoS Policy Management
In This Chapter
Overview page 86
Examples: Guarantees and Limits page 87
Differentiated Services (DiffServ) page 93
Low Latency Queuing page 95
Authenticated QoS page 103
Citrix MetaFrame Support page 104
Load Sharing page 106
Overview
86
OverviewThis chapter describes the more advanced QoS policy management procedures that enable you to refine the basic QoS policies described in Chapter 3, “Basic QoS Policy Management””.
Examples: Guarantees and Limits
Chapter 5 Advanced QoS Policy Management 87
Examples: Guarantees and LimitsThe QoS Action properties defined in the rules and sub-rules of a QoS Policy Rule Base interact with one another to determine bandwidth allocation.
The guidelines and examples in the sections that follow explain how to use guarantees and limits effectively.
In This Section
Per Rule Guarantees1. The bandwidth allocated to the rule is a combination of the guaranteed
bandwidth, plus the bandwidth that is given to the rule because of its weight. The guaranteed bandwidth is first “extracted” from the total bandwidth and set aside so that the guarantee can be upheld. The remaining bandwidth is then distributed according to the weights specified by all the rules. This means that the amount of bandwidth that is guaranteed to a rule is the guaranteed bandwidth plus the rule’s share of bandwidth according to weight.
Example:
The link capacity is 190KBps.
In this example, Rule A receives 130KBps, 100KBps from the guarantee, plus (10/30) * (190-100).
Rule B receives 60KBps, which is (20/30) * (190-100).
Per Rule Guarantees page 87
Per Connections Guarantees page 90
Limits page 91
Guarantee - Limit Interaction page 91
Table 5-1 Total Rule Guarantees
Rule Name Source Destination Service Action
Rule A Any Any ftp Rule Guarantee - 100KBpsWeight 10
Rule B Any Any http Weight 20
Per Rule Guarantees
88
2. If a guarantee is defined in a sub-rule, then a guarantee must be defined for the rule above it. The guarantee of the sub-rule can also not be greater than the guarantee of the rule above it.
Example:
This Rule Base is not correct because the guarantee is defined in sub-rule A1, but not in Rule A. To correct this, add a guarantee of 100KBps or more to Rule A.
3. A rule guarantee must not be smaller than the sum of guarantees defined in its sub-rules.
Table 5-2 Guarantee is Defined in Sub-rule A1, But Not in Rule A Making the Rule Incorrect
Rule Name Source Destination Service Action
Rule A Any Any ftp Weight 10
Start of Sub-Rule
Rule A1 Client-1 Any ftp Rule Guarantee - 100KBpsWeight 10
Rule A2 Client-2 Any ftp Weight 10
End of
Sub-Rule
Rule B Any Any http Weight 30
Per Rule Guarantees
Chapter 5 Advanced QoS Policy Management 89
Example:
This Rule Base is incorrect because the sum of guarantees in Sub-Rules A1 and A2 is (80 + 80) = 160, which is greater that the guarantee defined in Rule A (100KBps). To correct this, define a guarantee not smaller than 160KBps in Rule A, or reduce the guarantees defined in A1 and A2.
4. If a rule’s weight is low, some connections may receive very little bandwidth.
Table 5-3 Example of an Incorrect Rule Base
Rule Name Source Destination Service Action
Rule A Any Any ftp Rule Guarantee - 100KBpsWeight 10
Start of Sub-Rule
Rule A1 Client-1 Any ftp Rule Guarantee - 80KBpsWeight 10
Rule A2 Client-2 Any ftp Rule Guarantee - 80KBpsWeight 10
Rule A3 Client-3 Any ftp Weight 10
End of
Sub-Rule
Rule B Any Any http Weight 30
Per Connections Guarantees
90
Example:
The link capacity is 190KBps.
Rule A is entitled to 103KBps, which are the 100KBps guaranteed, plus (190-100) * (1/31). FTP traffic classified to Sub-Rule A1 receives the guaranteed 100KBps which is almost all the bandwidth to which Rule A is entitled. All connections classified to Sub-Rule A2 together receive only 1.5KBps, which is half of the remaining 3KBps.
5. The sum of guarantees in rules in the upper level should not exceed 90% of the capacity of the link.
Per Connections Guarantees1. If the Accept additional connections is checked, connections exceeding the
number defined in the Number of guaranteed connections are allowed to open. If you leave the field adjacent to Accept additional connections empty, the additional connections receive bandwidth allocated according to the Rule Weight defined.
2. If Per connection guarantees are defined both for a rule and for its sub-rule, the Per connection guarantee of the sub-rule should not be greater than the Per connection guarantee of the rule.
Table 5-4 If a Rule’s Weight is Low, Some Connections May Receive Very Little Bandwidth
Rule Name Source Destination Service Action
Rule A Any Any ftp Rule Guarantee - 100KBpsWeight 1
Start of Sub-Rule
Rule A1 Client-1 Any ftp Rule Guarantee - 100KBpsWeight 10
Rule A2 Client-2 Any ftp Weight 10
End of
Sub-Rule
Rule B Any Any http Weight 30
Limits
Chapter 5 Advanced QoS Policy Management 91
When such a Rule Base is defined, a connection classified to the sub-rule receives the Per connection guarantee that is defined in the sub-rule. If a sub-rule does not have a Per connection guarantee, it still receives the Per connection guarantee defined in the parent rule.
Limits1. If both a Rule Limit and a Per connection limit are defined for a rule, the Per
connection limit must not be greater than the Rule Limit.
2. If a limit is defined in a rule with sub-rules, and limits are defined in all the sub-rules, the rule limit should not be greater than the sum of limits defined in the sub-rules.
Having a rule limit that is greater than the sum of limits defined in the sub-rules is never necessary, because it is not possible to allocate more bandwidth to a rule than the bandwidth determined by the sum of the limits of its sub-rules.
Guarantee - Limit Interaction1. If a Rule Limit and a Guarantee per rule are defined in a rule, then the limit
should not be smaller than the guarantee.
2. If both a Limit and a Guarantee are defined in a rule, and the Limit is equal to the Guarantee, connections may receive no bandwidth, as in the following examples:
Guarantee - Limit Interaction
92
Example:
The Guarantee in sub-rule A1 equals the Guarantee in rule A (100KBps). When there is enough traffic on A1 to use the full Guarantee, traffic on A2 does not receive any bandwidth from A (there is a limit on A of 100KBps).
The steps that lead to this situation are as follows:
• A rule has both a guarantee and a limit, such that the limit equals the guarantee.
• The rule has sub-rules with Total Rule Guarantees that add up to the Total Rule Guarantee for the entire rule.
• The rule also has sub-rule(s) with no guarantee.
In such a case, the traffic from the sub-rule(s) with no guarantee may receive no bandwidth.
Table 5-5 No Bandwidth Received
Rule Name Source Destination Service Action
Rule A Any Any ftp Rule Guarantee — 100KBpsRule Limit 100KBpsWeight 10
Start of Sub-Rule
Rule A1 Client-1 Any ftp Rule Guarantee —100KBpsWeight 10
Rule A2 Client-2 Any ftp Weight 10
End of
Sub-Rule
Rule B Any Any http Weight 30
Differentiated Services (DiffServ)
Chapter 5 Advanced QoS Policy Management 93
Differentiated Services (DiffServ)In This Section
OverviewDiffServ is an architecture for providing different types or levels of service for network traffic. Packets are marked in the IP header TOS byte, inside the enterprise network as belonging to a certain Class of Service, or QoS Class. These packets are then granted priority on the public network.
DiffServ markings have meaning on the public network, not inside the enterprise network. (Effective implementation of DiffServ requires that packet markings be recognized on all public network segments.)
DiffServ Markings for IPSec PacketsWhen DiffServ markings are used for IPSec packets, the DiffServ mark can be copied from one location to another in one of two ways:
• :ipsec.copy_TOS_to_inner — The DiffServ mark is copied from the IPSec header to the IP header of the original packet after decapsulation/decryption.
• :ipsec.copy_TOS_to_outer — The DiffServ mark is copied from the original packet’s IP header to the IPSec header of the encrypted packet after encapsulation.
This property should be set, per QoS Module, in $FWDIR/conf/objects_5_0.c.
The default setting is:
:ipsec.copy_TOS_to_inner (false)
:ipsec.copy_TOS_to_outer (true)
Overview page 93
DiffServ Markings for IPSec Packets page 93
Interaction Between DiffServ Rules and Other Rules page 94
Interaction Between DiffServ Rules and Other Rules
94
Interaction Between DiffServ Rules and Other RulesA DiffServ rule specifies not only a QoS Class, but also a weight, in the same way that other QoS Policy Rules do. These weights are enforced only on the interfaces on which the rules of this class are installed.
For example, suppose a DiffServ rule specifies a weight of 50 for FTP connections. That rule is installed only on the interfaces for which the QoS Class is defined. On other interfaces, the rule is not installed and FTP connections routed through those other interfaces do not receive the weight specified in the rule. To specify a weight for all FTP connections, add a rule under “Best Effort.”
DiffServ rules can be installed only on interfaces for which the relevant QoS Class has been defined in the QoS tab of the Interface Properties window (FIGURE 0-3 on page 116). “Best Effort” rules (that is, non-DiffServ rules) can be installed on all interfaces of gateways with QoS Modules installed. Only rules installed on the same interface interact with each other.
Low Latency Queuing
Chapter 5 Advanced QoS Policy Management 95
Low Latency QueuingIn This Section
OverviewFor most traffic on the Web (including most TCP protocols), the WFQ (Weighted Fair Queuing, see “Intelligent Queuing Engine” on page 31) paradigm is adequate. This means that packets reaching FloodGate-1 are put in queues and forwarded according to the interface bandwidth and the priority of the matching rule. Using this standard policy, FloodGate-1 avoids dropping packets as often as possible, because such drops may adversely affect TCP. Avoiding drops, however, means holding (possibly long) queues, which may lead to non-negligible delays.
For some types of traffic, such as voice and video, bounding this delay is important. Long queues are inadequate for these types of traffic because they lead to substantial delay. Fortunately, for most “delay sensitive” applications, there is no need to drop packets from queues in order to keep them short.
Instead, the fact that the streams of these applications have a known, bounded bit rate can be utilized. If FloodGate-1 is configured to forward as much traffic as the stream delivers, then only a small number of packets accumulate in the queues and delay is negligible.
FloodGate-1 Low Latency Queuing makes it possible to define special Classes of Service for “delay sensitive” applications like voice and video. Rules under these classes can be used together with other rules in the QoS Policy Rule Base. Low Latency classes require you to specify the maximal delay that is tolerated and a Constant Bit Rate. FloodGate-1 then guarantees that traffic matching rules of this type is forwarded within the limits of the bounded delay.
Low Latency ClassesFor information on installing Low Latency Classes, see “Low Latency Classes” on page 95.
Overview page 95
Low Latency Classes page 95
Interaction between Low Latency and Other Rule Properties page 100
When to Use Low Latency Queuing page 101
Low Latency versus DiffServ page 102
Low Latency Classes
96
For each Low Latency class defined on an interface, a constant bit rate and maximal delay should be specified for active directions. FloodGate-1 checks packets matched to Low Latency class rules to make sure they have not been delayed for longer than their maximal delay permits. If the maximal delay of a packet has been exceeded, it is dropped. Otherwise, it is transmitted at the defined constant bit rate for the Low Latency class to which it belongs.
If the Constant Bit Rate of the class is defined correctly (meaning that it is not smaller than the expected arrival rate of the matched traffic), packets are not dropped (provided that the delay exceeds some minimum, see “Computing Maximal Delay” on page 97). On the other hand, when the arrival rate is higher than the specified Constant Bit Rate, packets exceeding this constant rate are dropped to ensure that those transmitted are within the maximal delay limitations.
Low Latency Class PrioritiesIn most cases, one Low Latency class is sufficient to serve all bounded delay traffic. In some cases, however, the user may need to define more than one Low Latency class. For this purpose, Low Latency classes are assigned one out of five priority levels (not including the Expedited Forwarding class, see “Low Latency versus DiffServ” on page 102). These priority levels are relative to other Low Latency classes.
It is advisable to define more than one Low Latency class if different types of traffic require different maximal delays.
The class with the lower maximal delay should get a higher priority than the class with the higher delay. The reason for this is that when two packets are ready to be forwarded, one for each Low Latency class, the packet from the higher priority class is forwarded first. The remaining packet (from the lower class) then encounters greater delay. This implies that the maximal delay that can be set for a Low Latency class depends on the Low Latency classes of higher priority.
Other Low Latency classes can affect the delay incurred by a class and therefore must be taken into consideration when determining the minimal delay that is feasible for the class. This is best done by initially setting the priorities for all Low Latency classes according to maximal delay, and then defining the classes according to descending priority. When you define class two, for example, class one should already be defined.
Note - The maximal delay set for a Low Latency class is an upper limit. This means that packets matching the class are always forwarded with a delay not greater, but often smaller, than specified.
Low Latency Classes
Chapter 5 Advanced QoS Policy Management 97
For more information on the effects of class priority on computing maximal delay, see “Computing Maximal Delay” on page 97.
Logging LLQ InformationSmartView Tracker enables you to log extensive information for all aspects of LLQ. For more information, see “SmartView Tracker” on page 169.
Computing the Correct Constant Bit Rate and Maximal Delay
Limits on Constant Bit Rate
For each direction of an interface (inbound and outbound), the sum of the constant bit rates of all the Low Latency classes cannot exceed 20% of the total designated bandwidth rate. The 20% limit is set to ensure that “Best Effort” traffic does not suffer substantial delay and jitter as a result of the existing Low Latency class(es).
Computing Constant Bit Rate
To compute the Constant Bit Rate of a Low Latency class, you should know the bit rate of a single application stream in traffic that matches the class and the number of expected streams that are simultaneously opened. The Constant Bit Rate of the class should be the bit rate of a single application, multiplied by the expected number of simultaneous streams.
If the number of streams exceeds the number you expected when you set the Constant Bit Rate, then the total incoming bit rate exceeds the Constant Bit Rate, and many drops occur. You can avoid this situation by limiting the number of concurrent streams. For more information, see “Ensuring that Constant Bit Rate is Not Exceeded (Preventing Unwanted Drops)” on page 100.
Computing Maximal Delay
To compute the maximal delay of a Low Latency class, you should take into account both the maximal delay that streams matching the class can tolerate in FloodGate-1 and the minimal delay that FloodGate-1 can guarantee this stream.
Note - Unlike bandwidth allocated by a Guarantee, the constant bit rate allocated to a Low Latency class on an interface in a given direction is not increased in the event that more bandwidth is available.
Low Latency Classes
98
It is important not to define a maximal delay that is too small, which may lead to unwanted drops. The delay value defined for a class determines the number of packets that can be queued in the Low Latency queue before drops begin to occur. The smaller the delay, the shorter the queue. Therefore, an insufficient maximal delay may cause packets to be dropped before they have the chance to be forwarded. It is advisable to allow for at least several packets to be queued, as explained in the steps below.
If you are using Check Point SmartView Tracker, it is recommended to use the default Class Maximal Delay defined in the LLQ log. In order to obtain this default number, you must first configure the correct Constant Bit Rate for the Class and you must give an estimation for the Class Maximal Delay. For more information, see “SmartView Tracker” on page 169. Alternately, you can set the Class Maximal Delay, as described in the steps that follow. If you use the following method you can set the delay of the class by obtaining estimates for the upper and lower bounds, and setting the delay to a value between the bounds:
1. Estimate the greatest delay that you can set for the class:
1. Refer to the technical details of the streaming application and find the delay that it can tolerate.
For voice applications, for example, it is commonly stated that the user starts to experience irregularities when the overall delay exceeds 150 ms.
2. Find or estimate the bound on the delay that your external network (commonly the WAN) imposes. Many Internet Service Providers publish Service Level Agreements (SLAs) that guarantee certain bounds on delay.
3. The maximal delay should be set at no more than the delay that the streaming application can tolerate minus the delay that the external network introduces.
This ensures that when the delay introduced by FloodGate-1 is added to the delay introduced by the external network, and does not exceed the delay tolerated by the streaming application.
2. Estimate the smallest delay that you can set for the class:
1. Find the bit rate of the streaming application in the application properties, or using Check Point SmartView Monitoring (see SmartView Monitor Administration Guide).
Note - Even if you set the Constant Bit Rate of the class to accommodate multiple simultaneous streams, conduct the following calculations with the streaming rate of a single stream.
Low Latency Classes
Chapter 5 Advanced QoS Policy Management 99
2. Estimate the typical packet size in the stream. You can either find it in the application properties or monitor the traffic.
If you do not know the packet size, you can use the size of the MTU of the LAN behind FloodGate-1. For Ethernet, this number is 1500 Bytes.
3. Many LAN devices, including switches and NICs, introduce some burstiness to flows of constant bit rate by changing the delay between packets. For constant bit rate traffic generated in the LAN and going out to the WAN, it is therefore recommended to monitor the stream packets on the FloodGated gateway (on the internal interface that precedes FloodGate-1) to get an estimate of burst size.
4. If no burstiness is detected, the minimal delay of the class should be no smaller than:
This enables three packets to be held in the queue before drops can occur. (Note again that the bit rate should represent a single application, even if you set the Constant Bit Rate of the class to accommodate multiple streams.)
If burstiness is detected, set the minimal delay of the class to be at least:
3. The maximal delay that you choose for the class should be between the smallest delay (estimated in step 2 on page 98) and the greatest delay (estimated in step 1 on page 98). Setting it very close to either of these values is not recommended. However, if you expect the application to burst occasionally, or if you don’t know whether the application generates bursts at all, then you should set the delay close to the greatest value.
4. When you enter the maximal delay you calculated, you may get an error box containing the message “The inbound/outbound maximal delay of class... must be greater than... milliseconds.”
This can occur if the Class of Service that you define is not of the first priority (see “Low Latency Class Priorities” on page 96). The delay value displayed in the error message depends on the Low Latency classes of higher priority, and on interface speed.
Set the maximal delay to a value no smaller than the one printed in the message.
3 packet size×bit rate
-----------------------------------
burst size 1+( ) packet size×bit rate
---------------------------------------------------------------------
Interaction between Low Latency and Other Rule Properties
100
Ensuring that Constant Bit Rate is Not Exceeded (Preventing Unwanted Drops)As explained in “Logging LLQ Information” on page 97, if the aggregate bit rate going through the Low Latency class exceeds the Constant Bit Rate of the class, then drops occur. This situation may occur when the number of streams actually opened exceeds the number you expected when you set the Constant Bit Rate.
To ensure that more streams than allowed are opened through a Low Latency Class, define a single rule under the class, with a per connection guarantee as its Action. In the Per Connection Guarantee field of the QoS Action Properties window, define the per connection bit rate that you expect, and in the Number of guaranteed connections field define the maximal number of connections that you allow in this class. The Accept additional non-guaranteed connections option should not be checked.
In this way, you can limit the number of connections to the number you used to compute the Constant Bit Rate of the class.
Interaction between Low Latency and Other Rule Properties
To activate a Low Latency class, you should define at least one rule under it in the QoS Policy Rule Base, however you may define more than one rule. The traffic matching any Low Latency class rule receives the delay and Constant Bit Rate properties defined for the specified class and is also treated according to the rule properties (weight, guarantee and limit).
You can use all types of properties in the rules under the Low Latency class, including Weight, Guarantee, Limit, Per Connection Guarantee and Per Connection Limit.
To better understand the integration of Low Latency class and rule properties, consider the class with its rules as a separate network interface forwarding packets at a rate defined by the Constant Bit Rate with delay bounded by the class delay, and with the rules defining the relative priority of the packets before they arrive at
When to Use Low Latency Queuing
Chapter 5 Advanced QoS Policy Management 101
the interface. If a rule has a relatively low priority, then packets matching it are entitled to a small portion of the Constant Bit Rate, and hence prone to more drops if the incoming rate is not small enough.
When to Use Low Latency QueuingUse Low Latency Queuing in the following cases:
• When low delay is important, and the bit rate of the incoming stream is known. This is the case for video and voice applications. In such cases, specify both the maximal delay and the Constant Bit Rate of the class.
• When controlling delay is important, but the bit rate is not known in advance. The most common example is Telnet. This application requires fast responses, but the bit rate is not known in advance. In addition, even if the stream occasionally exceeds the Constant Bit Rate, you do not want to experience drops. It is preferable to experience a somewhat larger delay. In such cases, set the Constant Bit Rate of the class to an upper estimate of the stream rate, and set a very large maximal delay (such as 99999 ms). The large delay ensures that packets are not dropped even in the event of a burst exceeding the Constant Bit Rate. They are queued and forwarded according to the Constant Bit Rate.
Do not use a Low Latency Class when controlling delay is not of prime importance. For most TCP protocols (such as HTTP, FTP and SMTP) the other type of FloodGate-1 rule is more appropriate. Use Weights, Limits and Guarantees in such cases, so the exact priority of the traffic is imposed without having to take care of bit rate and delay. FloodGate-1 enforces the policy with minimal drops. Moreover, weights and guarantees dynamically fill the pipe when some types of expected traffic are not present, while Low Latency Queuing firmly bounds its traffic by the Constant Bit Rate.
Note - Using sub-rules under the low latency class is not recommended because they make it difficult to compute the streams that suffer drops and the drop pattern. Guarantees and limits are not recommended for the same reasons (with the exception of Per Connection Guarantees, as described in “Ensuring that Constant Bit Rate is Not Exceeded (Preventing Unwanted Drops)” on page 100.
Note - When the incoming stream is smaller than the Constant Bit Rate, the actual delay is much smaller than 99999 ms (in the example above), because packets are forwarded almost as soon as they arrive. The 99999 ms bound is effective only for large bursts.
Low Latency versus DiffServ
102
Low Latency versus DiffServLow Latency classes differ from DiffServ classes in that they do not receive type of service (TOS) markings. Packets are not marked as Low Latency in a universal manner, and this preferential treatment can only be guaranteed for the QoS Module through which they pass.
The exception to this rule is the Expedited Forwarding DiffServ class. Any DiffServ class defined as an Expedited Forwarding class automatically becomes a Low Latency class of highest priority. Such a class receives the conditions afforded it by its DiffServ marking both in FloodGate-1 and in the rest of the network.
When to Use DiffServ and When to Use LLQIf you need to limit the delay for some types of traffic, you should use Low Latency Queuing except in the following two cases, when you should mark your traffic using a DiffServ class (see “When to Use Low Latency Queuing” on page 101):
• when your ISP supports DiffServ, meaning that you can receive a different level of QoS according to the DiffServ marking that you apply to the IP packets.
• when your ISP provides you with several Classes of Service using MPLS. In this case, DiffServ marking serves to “communicate” to your ISP the Class of Service that you expect every packet to receive.
Note - To use the Expedited Forwarding class as DiffServ only, without delay being enforced, specify a Maximal Delay value of 99999 in the Interface Properties tab (see “Low Latency Classes” on page 95).
Authenticated QoS
Chapter 5 Advanced QoS Policy Management 103
Authenticated QoSCheck Point Authenticated QoS provides Quality of Service (QoS) for end-users in dynamic IP environments, such as remote access and DHCP environments. This enables priority users, such as corporate CEOs, to receive priority service when remotely connecting to corporate resources.
Authenticated QoS dynamically prioritizes end-users, based on information gathered during network or VPN authentication. The feature leverages Check Point UserAuthority technology to classify both inbound and outbound user connections. The User Authority Server (UAS), maintains a list of authenticated users. When you query the UAS, Check Point QoS retrieves the data and allocates bandwidth accordingly.
FloodGate-1 supports Client Authentication, including Encrypted Client Authentication, and SecuRemote/SecureClient Authentication. User and Session Authentication are not supported.
For information about Client Authentication, see Firewall and SmartDefense Administration Guide.
Citrix MetaFrame Support
104
Citrix MetaFrame Support In This Section
OverviewCitrix MetaFrame is a client/server software application that enables a client to run a published application on a Citrix server farm from the client's desktop. It provides:
• Load balancing by automatically directing a client to the server with the lightest load in a server farm and by allowing publishing and application management from a single server in that farm.
• A secure encryption option via the ICA (Independent Computing Architecture) protocol developed by Citrix.
One of the disadvantages of using Citrix ICA is that, uncontrolled, printing traffic would consume all the available bandwidth, leaving mission critical applications struggling for bandwidth. There is, therefore, a critical need to provide service differentiation both between Citrix and other types of traffic, as well as within Citrix (layer 7) traffic.
Check Point QoS, from NG with Application Intelligence (R55), solves the problem by:
• Classifying all ICA applications running over Citrix through layer 7.
• Differentiating between the Citrix traffic based on ICA published applications, ICA printing traffic (Priority Tagging) and NFuse.
For further information, see “Managing QoS for Citrix ICA Applications” on page 155.
Check Point QoS, from NG with Application Intelligence (R55) manages QoS for printing over Citrix using the following service:
• Citrix_ICA_printing service: Citrix ICA printing traffic service.
For further information, see “Managing QoS for Citrix Printing” on page 162.
Overview page 104
Limitations page 105
Limitations
Chapter 5 Advanced QoS Policy Management 105
Limitations• The Citrix TCP services are supported in Traditional mode QoS Policies only.
• Session Sharing must be disabled.
• The number of applications that are detected by the inspection infrastructure is limited to 2048. Console errors will be sent if this limit is exceeded. These errors are harmless and will not affect your system. Simply restart the machine.
• Versions of MetaFrame prior to 1.8 are not supported because there is no packet tagging in these versions.
• Only one Citrix TCP service can be allocated per single rule.
Load Sharing
106
Load Sharing
OverviewLoad Sharing is a mechanism that distributes traffic within a cluster of gateways so that the total throughput of multiple machines is increased. Check Point QoS architecture guarantees that Load Sharing will provide either:
• Two-way Stickiness - all packets of a single connection use the same machine in both directions.
• Conversation Stickiness - all packets of control/data connections within a conversation use the same machine in both directions.
In Load Sharing configurations, all functioning machines in the cluster are active, and handle network traffic (Active/Active operation). If there is a failure in one of the machines, its connections are redistributed amongst the remaining operational machines in the cluster.
If any individual Check Point gateway in the cluster becomes unreachable, transparent failover occurs to the other machines, thus providing High Availability. All connections are shared between the remaining gateways without interruption.
All cluster servers share the same set of so called "virtual" interfaces. Each virtual interface corresponds to an outgoing link. An example of a typical cluster setting is presented in Figure 5-1.
Note - The new Check Point High Availability is a special type of load sharing that automatically works with QoS Load Sharing. These modes can be safely switched. To enforce the change though, The QoS policy has to be reinstalled.
Check Point QoS Cluster Infrastructure
Chapter 5 Advanced QoS Policy Management 107
Figure 5-1 Cluster Example
Check Point QoS provides a fault-tolerant QoS solution for cluster load sharing that deploys a unique, distributed WFQ bandwidth management technology. The user is able to specify a unified QoS policy per virtual interface of the cluster. The resulting bandwidth allocation is therefore identical to that obtained by installing the same policy on a single server.
Check Point QoS Cluster InfrastructureThis section describes the cluster infrastructure needed for QoS load sharing.
Note - Under a load state there are a few connections that are backlogged active for short periods of time. In such cases the Load Sharing function in ClusterXL are not spread evenly, but in this case there is no congestion and therefore no need for QoS.
Check Point QoS Cluster Infrastructure
108
Cluster State ClusterXL introduces a member's load value. A member's load, calculated in percentages, is assigned to each member by the cluster. The load is different for ClusterXL multicast and unicast modes. Generally the load for the N members in the cluster equals (100 / N)%. If number of cluster members changes dynamically (due to failover or recovery) the load is dynamically adjusted by the cluster to the appropriate value.
Changes in Cluster StateCluster members are informed of changes in a fellow cluster member’s load. All cluster members, including the causer member recalculate their rates with respect to the new load.
In this way, on the next re-calculation of rates the failed machine’s unutilized bandwidth, will be divided between the active cluster members. This guarantees correct work and the quick recovery of the system when faults have occurred.
Rates Calculation AlgorithmQoS Load Sharing uses a member's load value in order to obtain correct rates allocation for QoS rules.
The rates of the cluster members are calculated in the context of each virtual network interface. These calculations are used for enforcing the scheduling policy of a virtual network interface by setting the local rates of the corresponding real network interface of the cluster members. The cluster member executes this calculation each time ClusterXL informs them of changes in the cluster state.
Basically, in a centralized policy the rate of a rule is divided equally between the matching connections. In load sharing, the set of connections is evenly split between the cluster members by the decision function. Therefore, any rule and sub-rule of a cluster member is assigned a fraction of the original rate that is proportional to the load of member in the cluster. To achieve a guaranteed rate, the limit and allotment of each centralized policy rule are recalculated proportionally to the load of the each member.
Finally, a member's physical interface limit is calculated as a portion of the cluster interface limit, proportional to the member's load.
Note - If for any reason the QoS daemon cannot retrieve a load from the Check Point Load Sharing, it calculates the load statically according to the (100 / N)% formula. Where N is the number of members configured in the cluster topology and which are not necessarily active.
Check Point QoS Cluster Infrastructure
Chapter 5 Advanced QoS Policy Management 109
Per-connection guarantees are processed separately (Per-connection limit implementation remains unchanged by the load sharing mechanism.)
Per-Connection Guarantee AllocationEach rule with a per connection guarantee manages its rate budget. A rule's budget is the sum of all per connection guarantee rates over the number of per-connection guarantee connections allowed under this rule.
In order to decide whether a new connection receives its per-connection guarantee, the overall rate, which has already been granted to the matched rule's per-connection guarantee is checked. If this rate is below the rule's budget then the new connection is granted its per-connection guarantee.
This budget is also divided among cluster members proportionally to their cluster load. So, generally, each member will process only half the allowed per-connection guarantee matched to the rule. In this way the cluster as a whole will grant per-connection guarantee service according to the cluster’s QoS policy.
Example of Rates CalculationConsider a cluster consisting of two machines with one virtual interface configured to the rate of 125KBps. The centralized scheduling policy as well as the corresponding local scheduling policies are shown in Figure 5-1.Figure 5-2 Centralized Policy Rates
Check Point QoS Cluster Infrastructure
110
ConclusionThe decision function distributes traffic evenly between all cluster members and the resultant load sharing allocates exactly the same rates to the rules/connections as would be done by a centralized policy.
111
Chapter 6Managing Check Point QoS
In This Chapter
This chapter describes how to configure and manage Check Point QoS. The procedures described in this chapter all presuppose that you have already started the SmartDashboard application as described on page 57.
Defining QoS Global Properties page 112
Specifying Interface QoS Properties page 114
Editing QoS Rule Bases page 118
Modifying Rules page 123
Defining Sub-Rules page 142
Working with Differentiated Services (DiffServ) page 144
Working with Low Latency Classes page 150
Working with Authenticated QoS page 153
Managing QoS for Citrix ICA Applications page 155
Managing QoS for Citrix Printing page 162
Viewing the Check Point QoS Modules Status page 164
Enabling Log Collection page 165
Defining QoS Global Properties
112
Defining QoS Global PropertiesYou can define the QoS Global Properties, including the maximum weight of a QoS rule, the default value for the weight of a new QoS rule, the unit of measure for displaying transmission rates, and various timeout values for the implementation of the QoS rules.
To Modify the QoS Global Properties1. From the Policy menu, choose Global Properties or click the Edit Global
Properties icon in the toolbar. The Global Properties window is displayed.
2. Click QoS in the tree that appears on the left side of the page. The QoS page of the Global Properties window is displayed (FIGURE 0-1).FIGURE 0-1 Global Properties Window - FloodGate-1 Page
3. The following properties that apply to QoS rules are displayed. You can change any of these fields:
In the Weight area:
To Modify the QoS Global Properties
Chapter 6 Managing Check Point QoS 113
• Maximum weight of rule: The maximum weight that can be assigned to rules. The default value is 1000, but can be changed to any number.
• Default weight of rule: The weight to be assigned in the Action column by default to new rules, including new Default rules.
In the Rate area:
• Unit of measure: The unit specified in FloodGate-1 windows by default for transmission rates (for example, Bps - Bytes per second).
In the Authenticated timeout for QoS area:
• Authenticated IP expires after: If a user has been authenticated, all connections that are opened within the specified time receive the guaranteed bandwidth connection. Any connection opened after the specified time will be queried with the User Authority Server (UAS) again.
• Non authenticated IP expires after: If a user has previously tried and failed to be authenticated by the QoS Policy, then all connections that are opened within the specified time will not receive the guaranteed bandwidth connection. This means that they will not match that specific rule during that time.
• Unresponded queried IP expires after: The User Authority Server (UAS) database is queried to see if a user’s IP has been previously authenticated using Client Authentication or SSL. Until an answer is received, connections from this user will be classified to the next matching rule. If an answer is not received within the specified time, there will be another query.
4. Click OK to save the changes to the QoS Global Properties.
Note - Click Set Default to restore the default settings for the Authentication timeout for QoS parameters.
Specifying Interface QoS Properties
114
Specifying Interface QoS PropertiesYou must first define the network objects, that is, the gateway and its interfaces on which QoS controls traffic flow. For further information, see Network Objects in SmartCenter Administration Guide.
After defining the interfaces you can specify the QoS properties for those interfaces. This is done in the QoS tab of the Interface Properties window. Defining the interface QoS properties involves setting the Inbound and Outbound active transmission rates and specifying the Differentiated Services (DiffServ) and Low Latency classes. You can change these definitions at any time.
To Define the Interface QoS Properties1. Open the Properties window for the appropriate gateway by double-clicking the
gateway in the Objects Tree, or by choosing the gateway from the list in the Network Objects window. The Check Point Gateway - General Properties window is displayed (FIGURE 0-2).
Note - The QoS tab is only enabled for the interfaces of gateways that have FloodGate-1 checked under Check Point Products in the General Properties of the Check Point
Gateway window, as shown in FIGURE 0-2 on page 115.
To Define the Interface QoS Properties
Chapter 6 Managing Check Point QoS 115
FIGURE 0-2 Check Point Gateway - General Properties
2. Choose Topology in the tree on the left side of the Check Point Gateway - General Properties window. The Check Point Gateway - Topology window is displayed.
3. If a list of the gateway’s interfaces are not already present, click Get... to automatically retrieve the interfaces’ information. If you choose this method of configuring the gateway, the topology fetched suggests the external interface of the gateway based on the QoS Module routing table. You must ensure that this information is correct.
Alternatively, clicking Add displays the Interface Properties window. Interface information can then be defined in the General and Topology tabs of this window.
4. Double-click on the appropriate interface, or select it and click Edit. The Interface Properties window is displayed.
5. Click the QoS tab. The QoS tab is displayed (FIGURE 0-3).
To Define the Interface QoS Properties
116
FIGURE 0-3 Interface Properties Window - QoS Tab
6. Check Inbound Active to enable FloodGate-1 to control traffic on this interface in the inbound direction.
7. From the Rate dropdown list select the available bandwidth in the inbound direction, or enter the interface rate manually.
8. Check Outbound Active to enable FloodGate-1 to control traffic on this interface in the outbound direction.
9. From the Rate dropdown list select the available bandwidth in the outbound direction, or enter the interface rate manually.
Note - The interfaces on the WAN side (or the interface connected to the slower network) should usually be set to active. On a simple gateway with only two interfaces, FloodGate-1 should be installed only on the interface connected to the WAN. If the gateway also controls DMZ traffic, you may want to install FloodGate-1 on the interface connected to the DMZ.
Note - Ensure that the rates correspond to the actual physical capacity of the interfaces, as FloodGate-1 does not verify these values.
If the rate is incorrectly defined as less than the line’s real capacity, FloodGate-1will not use more than the capacity defined, and the excess capacity will remain unused. If the rate is incorrectly defined as more than the line’s real capacity, FloodGate-1 will not control the traffic correctly.
To Define the Interface QoS Properties
Chapter 6 Managing Check Point QoS 117
10. In the DiffServ and Low Latency classes area, you can specify the Differentiated Services (DiffServ) and Low Latency Queuing classes to be used on the interface.
You can Add, Edit or Remove a class. Refer to “Working with Differentiated Services (DiffServ)” on page 144 and “Working with Low Latency Classes” on page 150 for more details on adding or editing DiffServ and Low Latency Classes.
For information about DiffServ and Low Latency classes, see “Differentiated Services (DiffServ)” on page 93 and “Low Latency Queuing” on page 95.
11. Click OK to save the changes to the interface QoS properties.
12. Repeat from step 4. above for each of the relevant interfaces.
Editing QoS Rule Bases
118
Editing QoS Rule BasesA Policy Package comprises several Rule Bases, depending on the policy types selected.
Qos policy is implemented by defining an ordered set of rules in the Rule Base. The Rule Base is comprised of those rules which you create and a default rule. The default rule is automatically created with the Rule Base. It can be modified but cannot be deleted. The fundamental concept of the Rule Base is that unless other rules apply, the default rule is applied to all data packets. The default rule is therefore always the last rule in the Rule Base.
The Rule Base specifies what actions are to be taken with the data packets. It specifies the source and destination of the communication, what services can be used, at what times, whether to log the connection and the logging level.
A QoS Rule Base is applied to specific gateways and interfaces. After you have created the Policy Package and defined its QoS rules you must install it on the relevant QoS Modules.
For further details, refer to “Overview” on page 42.
In This Section
To Create a New Policy Package1. From the File menu choose New. The New Policy Package window is displayed.
2. Enter the name of the Policy Package in the New Policy Package Name field. This name cannot:
• Contain any reserved words or spaces.
• Start with a number.
• Contain any of the following characters:%, #, ‘, &, *,!, @, ?, <, >, /, \, :.
To Create a New Policy Package page 118
To Open an Existing Policy Package page 119
To Add a Rule page 119
To Rename a Rule page 121
To Copy, Cut or Paste a Rule page 121
To Delete a Rule page 122
To Open an Existing Policy Package
Chapter 6 Managing Check Point QoS 119
• End with any of the following suffixes: .w, .pf, .W.
3. In the QoS area, select whether you want Traditional mode or Express mode. See “Interaction with VPN-1Pro and VPN-1 Net” on page 39
4. Click OK to save the Policy Package to a new file. The new Policy Package is saved and a Default Rule is automatically created.
To Open an Existing Policy Package1. From the File menu choose Open. The Open Policy Package window is displayed.
2. Double-click on the appropriate Policy Package, or select it and click Open. The selected Policy Package is displayed.
To Add a RuleWhen you add rules to a Policy Package you can position the new rule at any location in the Policy Package. The Default Rule which is automatically created with the Rule Base must always remain in the last position in the Rule Base.
1. Position your mouse cursor in the Name field of the QoS tab, at the position where you want to add a new rule.
To Add a Rule
120
2. You can add the new rule either from the Rule menu or the toolbar, as described in Table 6-1, or you can also right-click on any name in the Name column of a rule to display the Rule menu, as described in Table 6-2.
Table 6-1 Adding a Rule
To add a rule Select from menu Toolbar
Button
After the last rule Rules > Add Rule > Bottom
Before the first rule Rules > Add Rule > Top
After the current rule Rules > Add Rule > Below
Before the current rule
Rules > Add Rule > Above
To the current rule Rules > Add Sub-Rule
Note - The current rule is the one that is highlighted. To select a rule, click on its name.
Table 6-2 Description of Rule Menu Items
Menu Option Explanation
Add Rule above Adds a rule before the current rule.
Add Rule below Adds a rule after the current rule.
Add Sub-Rule Adds a sub-rule after the current rule.
Delete Rule Deletes the current rule.
Copy Rule Copies the current rule to the clipboard.
Cut Rule Deletes the current rule and puts it in the clipboard.
Paste Rule Pastes the rule in the clipboard (a sub-menu is displayed from which you can select whether to paste the rule above or below the current rule).
To Rename a Rule
Chapter 6 Managing Check Point QoS 121
3. Select one of the options for creating the new rule. The Rule Name window is displayed.
4. Enter the name of the rule in the Rule Name field.
5. Click OK. The rule is added to the Rule Base at the selected position and is comprised of the default values defined in the FloodGate-1 page of the Global Properties window (FIGURE 0-1 on page 112). Follow the procedures described in the pages that follow to modify this rule.
To Rename a Rule1. In the QoS tab, double-click on the rule you want to rename, or right-click on
the rule and select Rename Rule. The Rule Name window is displayed.
2. Enter the rule name in the Rule Name field.
3. Click OK to save the rule name.
To Copy, Cut or Paste a RuleYou can copy, cut or paste a rule using either the Edit or Rules menus or the right-click menu of the selected rule.
1. In the QoS tab, select the rule you want to copy, cut or paste.
Add Class of Service Specifies a Class of Service (see “Differentiated Services (DiffServ)” on page 93 and “Low Latency Queuing” on page 95). A sub-menu is displayed from which you can select whether the Class of Service is to be added above or after the current rule.
Hide Rule Hides the current rule. The rule is still part of the Rule Base and will be installed when the QoS Policy is installed.
Disable Rule Disables the current rule. The rule appears in the Rule Base but is not enforced by the QoS Policy.
Rename Rule Renames the current rule.
Matching Method Starting from FloodGate-1 NG this feature is not relevant since it is kept for backward compatibility only (version 4.1).
Table 6-2 Description of Rule Menu Items
Menu Option Explanation
To Delete a Rule
122
2. From the Edit or Rules menu, choose one of the options described in Table 6-3.
If you choose Paste, then the Paste menu will be opened. You must then select Bottom, Top, Above, or Below to specify where in the Rule Base to paste the rule.
To Delete a RuleYou can delete a rule using either the Edit or Rules menus or the right-click menu of the selected rule.
1. In the QoS tab, select the rule you want to delete.
2. From the Edit or Rules menu, choose one of the options described in Table 6-4.
3. Click Yes to delete the selected rule.
Table 6-3 Copying, Cutting and Pasting Rules
Action Select from menu Toolbar
Button
Cut Edit>Cut
Copy Edit>Copy
Paste Edit>Paste
Table 6-4 Deleting a Rule
Action Select from menu Toolbar Button
Cut Edit>Cut or
Modifying Rules
Chapter 6 Managing Check Point QoS 123
Modifying RulesYou can modify any of the rule fields, as often as you like, until the rule is in the form that you require. This includes specifying the source and destination of each communication, what services can be used at what times (including TCP, Compound TCP, UDP, and ICMP services), the actions to be taken with the data packets, whether you want to maintain a log of the entries for the selected rule, and on which interfaces of the QoS module the rule is enforced.Figure 6-1 SmartDashboard Rule Base Window
This section describes the procedures for modifying the various fields in a rule. Refer to “Overview” on page 42 for more details about rules.
In This Section
Modifying Sources in a RuleYou can modify the source(s) of the communication in a rule. You can add as many sources as required. In addition, you can restrict the sources of the rule to particular user groups, or to user groups originating from specific locations.
Modifying Sources in a Rule page 123
Modifying Destinations in a Rule page 126
Modifying Services in a Rule page 128
Modifying Rule Actions page 130
Modifying Tracking for a Rule page 135
Modifying Install On for a Rule page 135
Modifying Time in a Rule page 138
Modifying Sources in a Rule
124
In This Section
To Add Sources to a Rule1. From the Rule Base choose the rule you want to modify.
2. Right-click in the Source column of the selected rule and select Add. The Add Object window is displayed (FIGURE 0-4), listing the network objects defined in the Security Policy and the QoS Policy.FIGURE 0-4 Add Object Window
3. Select one or more network objects (using the standard Windows selection keys) to add to the rule’s Source.
4. Click OK. The objects are added to the Source field. You can add as many sources as required.
To Add User Access to the Sources of a Rule1. From the Rule Base choose the rule you want to modify.
To Add Sources to a Rule page 124
To Add User Access to the Sources of a Rule page 124
To Edit, Delete, Cut, Copy or Paste a Source in a Rule page 125
To View Where an Object is Used page 126
Note - You can also use the Add Object window to define new objects and delete or modify objects.
Modifying Sources in a Rule
Chapter 6 Managing Check Point QoS 125
2. Right-click in the Source column of the selected rule and select Add Users Access. The User Access window is displayed (FIGURE 0-5).FIGURE 0-5 User Access Window
3. Choose one of the user groups to add to the rule’s Source.
4. Select whether you want to restrict the Location, as follows:
• No restriction: There is no restriction on the source of the users. For example, if you choose All Users and check No restriction, then AllUsers@Any will be inserted under Source in the rule.
• Restrict to: The source is restricted to the network object you select in the list box. For example, the source object in the rule will be AllUsers@Local_Net.
5. Click OK to add the user access to the rule source.
To Edit, Delete, Cut, Copy or Paste a Source in a RuleYou can edit, delete, cut, copy or paste a source in a rule using the right-click menu of the selected source.
1. From the Rule Base choose the rule you want to modify.
2. Right-click on the Source of the selected rule and select one of the following options:
• Edit: The appropriate window is opened, according to the type of object selected, and you can change the object’s properties. (Alternatively, you can double-click on an object in the Source column of the selected rule to edit it.)
Modifying Destinations in a Rule
126
• Delete: The selected object is deleted. If you delete the last source object in the rule it is replaced by Any.
• Cut: The selected object is cut and put it in the clipboard.
• Copy: The selected object is copied to the clipboard.
• Paste: The object is pasted from the clipboard to the rule’s Source.
To View Where an Object is UsedYou can view where the selected object is used (in queries, active policies, and so on).
1. From the Rule Base choose the rule you want to modify.
2. Right-click on the Source of the selected rule and choose Where Used. The Object References window is displayed (FIGURE 0-6), showing you where the selected object is used (in queries, active policies, and so on).FIGURE 0-6 Object References Window
3. Click Close to return to the rule.
Modifying Destinations in a RuleYou can modify the destination(s) of the communication in a rule. You can add as many destinations as required.
Modifying Destinations in a Rule
Chapter 6 Managing Check Point QoS 127
In This Section
To Add Destinations to a Rule1. From the Rule Base choose the rule you want to modify.
2. Right-click in the Destination column of the selected rule and select Add. The Add Object window is displayed (FIGURE 0-4), listing the network objects defined in the Security Policy and the QoS Policy.
3. Select one or more network objects (using the standard Windows selection keys) to add to the rule’s Destination.
4. Click OK. The objects are added to the Destination field. You can add as many destinations as required.
To Edit, Delete, Cut, Copy or Paste a Destination in a RuleYou can edit, delete, cut, copy or paste a destination in a rule using the right-click menu of the selected source.
1. From the Rule Base choose the rule you want to modify.
2. Right-click on the Destination of the selected rule and select one of the following options:
• Edit: The appropriate window is opened, according to the type of object selected, and you can change the object’s properties. (Alternatively, you can double-click on an object in the Destination column of the selected rule to edit it.)
• Delete: The selected object is deleted. If you delete the last destination object in the rule it is replaced by Any.
• Cut: The selected object is cut and put it in the clipboard.
• Copy: The selected object is copied to the clipboard.
To Add Destinations to a Rule page 127
To Edit, Delete, Cut, Copy or Paste a Destination in a Rule page 127
To View Where an Object is Used page 130
Note - You can also use the Add Object window to define new objects and delete or modify objects.
Modifying Services in a Rule
128
• Paste: The object is pasted from the clipboard to the rule’s Destination.
To View Where an Object is UsedYou can view where the selected object is used (in queries, active policies, and so on).
1. From the Rule Base choose the rule you want to modify.
2. Right-click on the Source of the selected rule and choose Where Used. The Object References window is displayed (FIGURE 0-6), showing you where the selected object is used (in queries, active policies, and so on).
3. Click Close to return to the rule.
Modifying Services in a RuleYou can modify the service(s) in a rule. You can add as many services as required, however, you can only add one URI for QoS resource in a single rule.
In This Section
To Add Services to a Rule1. From the Rule Base choose the rule you want to modify.
2. Right-click in the Service column of the selected rule and select Add. The Add Object window is displayed (FIGURE 0-4), listing the network objects defined in the Security Policy and the QoS Policy.
3. Select one or more network objects (using the standard Windows selection keys) to add to the rule’s Service.
4. Click OK. The objects are added to the Service field. You can add as many services as required. However only one TCP Citrix or URI for QoS service is allowed.
Note - Previous versions of FloodGate-1 have not limited the number of URIs for QoS resources allowed per rule. If you are using a QoS Policy originally designed for use with a previous FloodGate-1 version, be sure to redefine any rule that has more than one resource in its Service Field.
To Add Services to a Rule page 128
To Add a Service with a Resource to a Rule page 129
To Edit, Delete, Cut, Copy or Paste a Service in a Rule page 129
To View Where an Object is Used page 130
Modifying Services in a Rule
Chapter 6 Managing Check Point QoS 129
To Add a Service with a Resource to a Rule1. From the Rule Base choose the rule you want to modify.
2. Right-click in the Source column of the selected rule and select Add with Resources. You can only add one service with a resource to a rule, so this option will only be available if you have not already added a service with a resource to this rule. The Services with Resource window is displayed (FIGURE 0-7). FIGURE 0-7 Services with Resource Window
3. Choose one of the services in the Location area and then select the appropriate resource from the Resource dropdown list. For further information, refer to:
• Only resources of type URI for QoS can be added to the FloodGate-1 Rule Base. URI for QoS is used for identifying HTTP traffic according to the URL (URI).
• Do not use the protocol prefix (http://) when setting up a URI resource. HTTP services with URI for QoS resources can be defined on all ports.
4. Click OK to add the service with a URI for QoS resource to the rule.
To Edit, Delete, Cut, Copy or Paste a Service in a RuleYou can edit, delete, cut, copy or paste a service in a rule using the right-click menu of the selected service.
1. From the Rule Base choose the rule you want to modify.
Note - Only one resource is allowed in a single rule.
Modifying Rule Actions
130
2. Right-click on the Service of the selected rule and select one of the following options:
• Edit: The appropriate window is opened, according to the type of object selected, and you can change the object’s properties. (Alternatively, you can double-click on an object in the Service column of the selected rule to edit it.)
• Delete: The selected object is deleted. If you delete the last service object in the rule it is replaced by Any.
• Cut: The selected object is cut and put it in the clipboard.
• Copy: The selected object is copied to the clipboard.
• Paste: The object is pasted from the clipboard to the rule’s Service.
To View Where an Object is UsedYou can view where the selected object is used (in queries, active policies, and so on).
1. From the Rule Base choose the rule you want to modify.
2. Right-click on the Service of the selected rule and choose Where Used. The Object References window is displayed (FIGURE 0-6), showing you where the selected object is used (in queries, active policies, and so on).
3. Click Close to return to the rule.
Modifying Rule ActionsYou can modify the default properties of a rule. The options available vary according to the action type of rule, that is whether the rule is defined as simple or advanced. The advanced rule action type enables you to specify limits and guarantee allocation on a per connection basis.
In This Section
To Edit the Rule Actions1. From the Rule Base choose the rule you want to modify.
To Edit the Rule Actions page 130
To Reset the Rule Actions to Default Values page 134
Modifying Rule Actions
Chapter 6 Managing Check Point QoS 131
2. Right-click in the Action column of the selected rule and select Edit Properties. The QoS Action Properties window is displayed, as follows:
• If the Action Type of the rule is defined as Simple, the QoS Action Properties window is displayed (FIGURE 0-8).
FIGURE 0-8 QoS Action Properties - Simple
• If the Action Type of the rule is defined as Advanced, the QoS Action Properties window is displayed (FIGURE 0-9).
Modifying Rule Actions
132
FIGURE 0-9 QoS Action Properties - Advanced
3. The following properties are displayed for a QoS rule with a simple action type. You can change any of these fields:
In the Action Type area:
• Simple: The full set of actions with the exception of the Guarantee Allocation and the per connection limit features.
• Advanced: The full set of actions with the Guarantee Allocation feature included.
In the VPN Traffic area:
• Allow rule only to encrypted traffic: Check this box if you want the rule to be matched only by VPN traffic. If you do not check this field, rules will be matched by all traffic types, both VPN and non-VPN traffic. VPN traffic means traffic that is encrypted in this same gateway by Check Point VPN. This field does not apply to traffic that was encrypted prior to arriving to this gateway. This type of traffic can be matched using the "IPSec" service,
Note - When Express QoS has been installed, Advanced Actions are not available.
Modifying Rule Actions
Chapter 6 Managing Check Point QoS 133
see the SmartCenter Administration Guide. For further explanation on how to use this check box for prioritizing VPN traffic over non-VPN, see “Example of a Rule Matching VPN Traffic” on page 48.
In the Action Properties area you can define the restrictions on bandwidth for connections to which the rule applies in the following fields:
• Rule Weight: Enables you to define the weight of the rule. This field is checked by default and has the value defined in the Global Properties window in “Defining QoS Global Properties” on page 112. It is recommended to leave this value as is to avoid a complete loss of bandwidth. For detailed information see “Weight” on page 45.
• Rule Limit: Enables you to restrict the total bandwidth consumed by the rule. For detailed information see “Limits” on page 46.
• Rule Guarantee: Enables you to define the absolute bandwidth allocated to the rule. For detailed information see “Guarantees” on page 46.
4. (Optional) The following additional properties are displayed for a QoS rule with an advanced action type. You can change any of these fields:
In the Limit area:
• Rule Limit: Enables you to restrict the total bandwidth consumed by the rule. For detailed information see “Limits” on page 46.
Warning - 0 rate in conjunction with 0 guarantee can lead to the rule’s complete loss of bandwidth. To prevent this from happening, retain some ratio in the Rule Weight. The default is 10.
Tip - When using weights or guarantees, the weighted fair queuing algorithm that Check Point QoS makes use of assures that no bandwidth is ever wasted. Spare bandwidth is divided among the backlogged rules. However, if you set a rule limit, it will not use spare bandwidth above this limit.
Note - The number you enter for the Rule Guarantee cannot be larger than the Rule Limit.
Tip - When using weights or guarantees, the weighted fair queuing algorithm that Check Point QoS makes use of assures that no bandwidth is ever wasted. Spare bandwidth is divided among the backlogged rules. However, if you set a rule limit, it will not use spare bandwidth above this limit.
Modifying Rule Actions
134
• Per connection limit: Enables you to set a rule limit per connection.
In the Guarantee Allocation area:
• Guarantee: Enables you to allocate a minimum bandwidth to the connections matched with a rule. For detailed information see “Guarantees” on page 46.
• Per rule: Enables you to define the absolute bandwidth allocated to the rule.
• Per connection: Enables you to manage the bandwidth at the connection-level.
• Per connection guarantee: Enables you to restrict the absolute bandwidth allocated per connection.
• Number of guaranteed connections: Enables you to allocate a minimum number of guaranteed connections
• Accept additional connections: Check this checkbox to allow connections without per connection guarantees to pass through this rule and receive any left over bandwidth. Enter the maximum amount of bandwidth that is allowed for this option in the text box. This only occurs if all other conditions have been met.
5. Click OK to update the QoS Action Properties for the rule.
To Reset the Rule Actions to Default Values1. From the Rule Base choose the rule you want to modify.
Note - The number you enter for the Rule Guarantee cannot be larger than the Rule Limit.
Note - The number you enter for the Per rule cannot be larger than the Rule Limit.
Note - The Number of guaranteed connections multiplied by the Per connection guarantee cannot be greater than the rule limit.
Note - Select a non-zero rule weight when Accept additional non-guaranteed connections is checked.
Modifying Tracking for a Rule
Chapter 6 Managing Check Point QoS 135
2. Right-click in the Action column of the selected rule and select Reset to Default. The action properties for the selected rule are reset to their default values. The default values are defined in the FloodGate-1 page of the Global Properties window (see “Defining QoS Global Properties” on page 112).
Modifying Tracking for a RuleYou can choose whether you want to maintain a log of the entries for the selected rule. If you do want to log the entries, you also have the option of logging the entries in account format. For further information on tracking and logging, see “Overview of Logging” on page 170. For information on how to turn logging on, see “Enabling Log Collection” on page 165.
To Modify Tracking for a Rule1. From the Rule Base choose the rule you want to modify.
2. Right-click in the Track column of the selected rule. The menu that is displayed has the following options:
Table 6-5 Track Menu
3. Select the required option.
Modifying Install On for a RuleThe Install On field specifies on which interfaces of the QoS module the rule is enforced. You can select any number of Install On objects.
Track Meaning
None: No logging is done for this connection.
Log: Logging is done for this connection.
Account: Logging for this connection is done in Accounting format.
Note - In order to install a QoS Policy on a gateway, you must ensure that the gateway has a QoS module installed in the Global Properties window and that the interface is defined in the QoS tab of the Interface Properties window. (See “Defining QoS Global Properties” on page 112 and “Specifying Interface QoS Properties” on page 114.)
Modifying Install On for a Rule
136
In This Section
To Modify Install On for a Rule1. From the Rule Base choose the rule you want to modify.
2. Right-click in the Install On column of the selected rule and select Add. The Add Interface window is displayed (FIGURE 0-10).FIGURE 0-10 Add Interface Window
3. (Optional) Click Select Targets to select additional installable targets. The Select Installation Targets window is displayed (FIGURE 0-11).
To Modify Install On for a Rule page 136
To Delete an Install On for a Rule page 137
To View Where an Object is Used page 138
Modifying Install On for a Rule
Chapter 6 Managing Check Point QoS 137
FIGURE 0-11 Select Installation Targets Window
1. To add any target(s) to the list of Installed Targets, select the target(s) in the Not in Installation Targets area and click . The selected target(s) are added to the In Installation Targets area.
2. To remove a target(s) from the In Installation Targets area, select the target(s) and click . The selected targets are returned to the Not in Installation Targets area.
3. Click OK. The selected targets now appear in the Add Interface window (FIGURE 0-10).
4. Select from the list of targets in the Add Interface window:
• A module (and all its interfaces on which QoS is defined), or
• An interface (in both directions), or
• One direction of an interface
5. Click OK. The selected interface is added to the Install On field.
To Delete an Install On for a RuleYou can remove an interface for a rule. The rule will no longer be enforced for the interface.
1. From the Rule Base choose the rule you want to modify.
Modifying Time in a Rule
138
2. Right-click on the Service of the selected rule and select Delete. The selected object is deleted.
To View Where an Object is UsedYou can view where the selected object is used.
1. From the Rule Base choose the rule you want to modify.
2. Right-click on the Install On of the selected rule and choose Where Used. The Object References window is displayed (FIGURE 0-6), showing you where the selected object is used.
3. Click Close to return to the rule.
Modifying Time in a RuleYou can specify the times that the rule is enforced. You add any number of time objects to a rule.
In This Section
To Modify Time in Rules1. From the Rule Base choose the rule you want to modify.
2. Right-click in the Time column of the selected rule and select Add. The Add Object window is displayed (FIGURE 0-12).
To Modify Time in Rules page 138
To Edit or Delete a Time Object for a Rule page 140
To View Where an Object is Used page 140
Modifying Time in a Rule
Chapter 6 Managing Check Point QoS 139
FIGURE 0-12 Add Object Window - Time Objects
3. (Optional) You can edit a time object:
1. Select the required time object and click Edit to modify a time object. The Time Properties window is displayed (FIGURE 0-13). (Alternatively, you can double-click on an object in the Time column of the selected rule to edit it.)
FIGURE 0-13 Time Properties Window
2. Edit the fields in the Time Properties window, as required.
3. Click OK. The Time Object Properties are amended.
Adding Comments to a Rule
140
4. Select the required time object in the Add Object window. The time object is added to the rule.
To Edit or Delete a Time Object for a RuleYou can edit or delete a time object in a rule using the right-click menu of the selected service.
1. From the Rule Base choose the rule you want to modify.
2. Right-click on the Time of the selected rule and select one of the following options:
• Edit: The appropriate window is opened, according to the type of object selected, and you can change the object’s properties. (Alternatively, you can double-click on an object in the Time column of the selected rule to edit it.)
• Delete: The selected object is deleted. If you delete the last time object in the rule it is replaced by Any.
To View Where an Object is UsedYou can view where the selected object is used (in queries, active policies, and so on).
1. From the Rule Base choose the rule you want to modify.
2. Right-click on the Service of the selected rule and choose Where Used. The Object References window is displayed (FIGURE 0-6), showing you where the selected object is used (in queries, active policies, and so on).
3. Click Close to return to the rule.
Adding Comments to a RuleYou can add a comment to a rule.
To Add Comments to Rules1. From the Rule Base choose the rule you want to modify.
2. Right-click in the Comment column of the selected rule and select Edit. The Comment window is displayed (FIGURE 0-14). You can also open this window by double-clicking in the Comment column of the selected rule.
Adding Comments to a Rule
Chapter 6 Managing Check Point QoS 141
FIGURE 0-14 Comment Window
3. Type any text you wish to add in the text box.
4. Click OK. The comment is added to the rule.
Defining Sub-Rules
142
Defining Sub-RulesSub-rules are rules that allocate bandwidth more specifically within a rule. For example, consider the rule shown in Figure 6-2.Figure 6-2 Rule Base with Sub-Rules
The bandwidth allocated to the ABC_VPN rule is further allocated among the sub-rules ABC_VPN_ERP through Default under ABC_VPN (see the rule tree).
In This Section
To Define Sub-Rules1. Select the rule under which the sub-rule is to be defined.
2. Right-click in the Rule Name column.
3. Select Add Sub-Rule from the menu. The Rule Name window is displayed.
4. Enter the sub-rule name and click OK. The new sub-rule together with a default sub-rule is automatically created, under the rule selected in 1 above, using the default values defined.
5. You may modify the sub-rules by following the same procedures for editing rules described on page 119.
6. Add new sub-rules by following the same procedures for creating rules described on page 119.
To View Sub-RulesThe sub-rules under a main rule can be seen by expanding the rule in the QoS Rule Tree.
To Define Sub-Rules page 142
To View Sub-Rules page 142
Defining Sub-Rules
Chapter 6 Managing Check Point QoS 143
To view sub-rules in the Rule Base itself, click one of the sub-rules in the relevant main rule. The Rule Base shows all the sub-rules for that rule.
Working with Differentiated Services (DiffServ)
144
Working with Differentiated Services (DiffServ)
A DiffServ rule specifies not only a QoS Class, but also a weight, in the same way that other QoS Policy Rules do. These weights are enforced only on the interfaces on which the rule is installed.
Refer to “Differentiated Services (DiffServ)” on page 93 for additional information on DiffServ.
In This Section
To Implement DiffServ Marking in FloodGate-11. Define one or more DiffServ Classes of Service using the QoS Classes window.
You may also define a Class of Service Group.
For more information, see “To Define a DiffServ Class of Service” on page 145.
2. In the QoS tab of the Interface Properties window of all interfaces on which the DiffServ class will be implemented (see “Specifying Interface QoS Properties” on page 114), click Add under DiffServ and Low Latency classes to add a new class, or Edit to edit the properties of an existing class. See “Specifying Interface QoS Properties” on page 114
3. In the Add QoS Class Properties window, select the QoS class and define the Inbound and Outbound parameters.
4. Click OK. You can now add QoS Classes to the QoS Policy Rule Base.
5. Right-click in the Name column of a rule and choose Add Class of Service, or choose Add QoS Class from the Rules menu.
6. Specify whether the class should appear above or after the rule in the Rule Base.
7. Choose the required Class of Service from the drop-down menu in the Add Class of Service window (FIGURE 0-15).
To Implement DiffServ Marking in FloodGate-1 page 144
To Define a DiffServ Class of Service page 145
To Define a DiffServ Class of Service Group page 146
To Add QoS Class Properties for Expedited Forwarding page 147
To Add QoS Class Properties for Non Expedited Forwarding page 148
To Define a DiffServ Class of Service
Chapter 6 Managing Check Point QoS 145
FIGURE 0-15 Add Class of Service Window
8. Click OK. A DiffServ class header appears in the Rule Base.
9. Add rules under the QoS Class you defined, by either:
• Choosing Rules > Add Rule > Below from the menu, or
• Right-clicking on the QoS Class and choosing Add Rule > Below from the menu
To Define a DiffServ Class of Service1. From the Manage menu select QoS>QoS Classes. The QoS Classes window
(FIGURE 0-16) is displayed.FIGURE 0-16 QoS Classes Window
2. Click New to define a new DiffServ class and select DiffServ Class of Service to display the Class of Service Properties window (FIGURE 0-17).
To Define a DiffServ Class of Service Group
146
FIGURE 0-17 Class of Service Properties Window
3. Enter the following details in the Class of Service Properties window:
• Name: The name of the Class of Service.
• Comment: The text to be displayed when this class is selected in the QoS Classes window (FIGURE 0-16).
• Color: Select a color from the dropdown list.
• Type: Select a type from the dropdown list. You may choose a predefined or user defined class.
• DiffServ code: This is a read-only field that displays the DiffServ marking as a bitmap.
4. Click OK to create the new DiffServ Class of Service.
To Define a DiffServ Class of Service Group1. From the Manage menu select QoS > QoS Classes. The QoS Classes window
(FIGURE 0-16) is displayed.
2. Click New to define a new DiffServ class and select DiffServ Class of Service Group to display the Group Properties window (FIGURE 0-18).
To Add QoS Class Properties for Expedited Forwarding
Chapter 6 Managing Check Point QoS 147
FIGURE 0-18 QoS Class of Services Group Window
3. Enter the following details in the Group Properties window:
• Name: The name of the group.
• Comment: The text to be displayed when this class is selected in the QoS Classes window (FIGURE 0-16).
• Color: Select a color from the dropdown list.
• To add a DiffServ class to the group, select the class in the list box labeled Not in Group, and click .
• To delete a class from the group, select the class in the list box labeled In Group, and click .
4. Click View expanded group to display all members of the selected DiffServ group.
5. Click OK to create the new DiffServ Class of Service Group.
To Add QoS Class Properties for Expedited Forwarding
1. From the QoS tab of the Interface Properties window FIGURE 0-3 on page 116, click Add or Edit.
To Add QoS Class Properties for Non Expedited Forwarding
148
2. From the menu that is displayed select either Low Latency Classes or DiffServ > Expedited Forwarding. The Add Low Latency QoS Class Properties window FIGURE 0-19 is displayed if you selected Low Latency Classes. If you selected DiffServ Expedited Forwarding, a similar window with the identical fields is displayed.FIGURE 0-19 Add Low Latency QoS Class Properties Window
3. Enter the required information as detailed below. You should define at least one inbound or outbound direction.
• Class: Select a Low Latency class from the list of defined classes.
• Inbound: Define the portion of the interface’s inbound capacity to be reserved.
• Constant Bit Rate: The constant bit rate at which packets of this class will be transmitted.
• Maximal Delay: The maximum delay that will be tolerated for packets of this class. Those packets that exceed this delay are dropped.
• Outbound: Define the portion of the interface’s outbound capacity to be reserved by defining a Constant Bit Rate and a Maximum Delay as described above.
4. Click OK. The new class is added.
To Add QoS Class Properties for Non Expedited Forwarding
1. From the QoS tab of the Interface Properties window FIGURE 0-3 on page 116, click Add or Edit.
2. From the menu that is displayed select DiffServ>Others. The Add DiffServ QoS class Properties window is displayed (FIGURE 0-19).
To Add QoS Class Properties for Non Expedited Forwarding
Chapter 6 Managing Check Point QoS 149
FIGURE 0-20 DiffServ QoS class Properties Window
3. Enter the required information as detailed below. You should define at least one inbound or outbound direction.
• Class: Select a DiffServ class from the list of defined classes.
• Inbound: Define the portion of the interface’s inbound capacity to be reserved.
• Guaranteed bandwidth: The bandwidth guaranteed to be marked with the QoS Class.
• Bandwidth Limit: The upper limit of the bandwidth to be marked with the QoS Class. Traffic in excess of the Bandwidth Limit will not be marked. For example, if the interface’s capacity is 256MB and Bandwidth Limit to 192MB, then traffic beyond 192MB will not be marked.
• Outbound: Define the portion of the interface’s outbound capacity to be marked by defining a Guaranteed Bandwidth and a Bandwidth Limit as described above.
4. Click OK. The new class is added.
Working with Low Latency Classes
150
Working with Low Latency ClassesFloodGate-1 Low Latency Queuing makes it possible to define special classes of service for “delay sensitive” applications like voice and video. Rules under these classes can be used together with other rules in the QoS Policy Rule Base. Low Latency classes require you to specify the maximal delay that is tolerated and a Constant Bit Rate. FloodGate-1 then guarantees that traffic matching rules of this type are forwarded within the limits of the bounded delay.
For more detailed information, please see “Low Latency Queuing” on page 95.
In This Section
To Implement Low Latency QueuingHaving defined one or more Low Latency Classes of Service, you can implement Low Latency Queuing as follows:
1. In the QoS tab of the Interface Properties window of all interfaces on which Low Latency classes are implemented (see “Specifying Interface QoS Properties” on page 114), click Add under DiffServ and Low Latency classes to add a new class, or Edit to edit the properties of an existing class.
2. In the Add QoS Class Properties window (FIGURE 0-19 on page 148), select the Low Latency class and define the Inbound and Outbound parameters (see “To Add QoS Class Properties for Expedited Forwarding” on page 147).
3. Click OK. You can now add Low Latency Classes to the QoS Policy Rule Base.
4. Right-click in the Name column of a rule and choose Add Class of Service, or choose Add QoS Class from the Rules menu.
5. Specify whether the class should appear above or below the rule in the Rule Base.
To Implement Low Latency Queuing page 150
To Define Low Latency Classes of Service page 151
To Define Class of Service Properties for Low Latency Queuing page 151
Note - The order of the classes in the Rule Base must be DiffServ, followed by Low Latency, and then Best Effort. You will not be able to add a Low Latency class to the Rule Base above any DiffServ classes you may have.
To Define Low Latency Classes of Service
Chapter 6 Managing Check Point QoS 151
6. Choose the required Class of Service from the drop-down menu in the Add Class of Service window (FIGURE 0-21).FIGURE 0-21 Add Class of Service Window
7. Click OK. A class header appears in the Rule Base.
8. Add rules under the QoS Class you defined, by either:
• Choosing Rules>Add Rule>Below from the menu, or
• Right-clicking on the QoS Class and choosing Add Rule>Below from the menu.
To Define Low Latency Classes of ServiceBefore a Low Latency class can be implemented on an interface and used in the FloodGate-1 Rule Base, it must be defined.
1. From the Manage menu select QoS>QoS Classes. The QoS Classes window is displayed (FIGURE 0-16 on page 145).
2. Define the Low Latency Class of Service as described in “To Define a DiffServ Class of Service” on page 145.
3. To define a new Low Latency class, click New and select Low Latency Class of Service to display the Class of Service Properties window (FIGURE 0-22 on page 152).
To Define Class of Service Properties for Low Latency Queuing
1. From the Manage menu select QoS > QoS Classes. The QoS Classes window is displayed (FIGURE 0-16 on page 145).
2. Click New and select Low Latency Class of Service to display the Class of Service Properties window (FIGURE 0-22).
To Define Class of Service Properties for Low Latency Queuing
152
FIGURE 0-22 Low latency Class of Service Properties Window
3. Enter the following details:
• Name: The name of the Class of Service.
• Comment: Enter the text to be displayed when this class is selected in the QoS Classes window (FIGURE 0-16 on page 145).
• Color: Select a color from the dropdown list.
• Class Priority: Select one of the five priority types from the dropdown list (Class 1 being the highest priority).
4. Click OK. The new Low Latency Class of Service is saved.
Working with Authenticated QoS
Chapter 6 Managing Check Point QoS 153
Working with Authenticated QoSCheck Point Authenticated QoS provides Quality of Service (QoS) for end-users in dynamic IP environments, such as remote access and DHCP environments. This enables priority users, such as corporate CEOs, to receive priority service when remotely connecting to corporate resources.
For more detailed information, please see “Authenticated QoS” on page 103.
To Use Authenticated QoSIn order to apply Authenticated QoS in a rule, follow these steps:
1. Make sure that the UAS package is installed on the module that performs Authenticated QoS.
2. Make sure that the User Authority Server, under Check Point Products Installed, is checked on the VPN-1 Power Module upon which you are installing the policy.
3. Create a group in Manage > Users > New > Group in the menu. The Group Properties window is displayed.
Figure 6-3 Group Properties Window
4. Include all the user(s) whom you want to give priority by selecting the user and clicking .
To remove a user from the group, select the user and click .
To Use Authenticated QoS
154
5. Make a rule and in the Source column, right-click and select Add User Access.
For example, if the CEO of your company is in a remote location and wants to access his email and without waiting too long, create a rule as follows:
6. Install the policy.
Policy-wide properties for Authenticated QoS can be defined in the FloodGate-1 page of the Global Properties window (FIGURE 0-1 on page 112). For more information, see “Defining QoS Global Properties” on page 112.
Table 6-6 A Rule that Allows Access to email from a Remote Location
Rule
Name
Source Destination Service Action
CEO CEO@localnet Any Pop-3 Weight 10Guarantee 50,000 Bps
Note - To minimize the resources taken up by Authenticated QoS, it is recommended that Authenticated QoS rules refer to specific services, and unless absolutely necessary, you should not include Any in the Service field.
Note - The user must be authenticated in the UAS in order for the QoS policy to be enforced.
Managing QoS for Citrix ICA Applications
Chapter 6 Managing Check Point QoS 155
Managing QoS for Citrix ICA ApplicationsIn order to deliver a QoS solution for the Citrix ICA protocol, complete the following procedures:
1. Disable session sharing in the Citrix Program Neighborhood.
2. Modify your Security Policy to allow the Citrix_ICA and Citrix_ICA_Browsing services.
3. Discover the Citrix application names, as defined by the Citrix Administrator, and retrieve your Citrix ICA application names from the SmartView Tracker. This includes turning on the application detection check box and installing Security and QoS Policies.
4. Define new Citrix TCP services with the application names you have detected.
5. Add the appropriate Citrix TCP services to rules in your QoS Policy.
6. Install the QoS Policy.
In This Section
Disabling Session SharingCitrix enables session sharing by default. In this mode, traffic from all the applications used by a specific client share the same TCP connection. In order for Check Point QoS to prioritize different Citrix ICA applications from the same client, you must disable session sharing. This means that every application uses a separate TCP connection (all going to the same server port, 1494, from different source ports).
Note - The Any service does not include the Citrix ICA service.
Disabling Session Sharing page 155
Modifying your Security Policy page 156
Discovering Citrix ICA Application Names page 157
Defining a New Citrix TCP Service page 160
Adding a Citrix TCP Service to a Rule (Traditional Mode Only) page 161
Installing the Security and QoS Policies page 161
Modifying your Security Policy
156
You should contact the Citrix Administrator to configure the correct mode.
To Disable Session Sharing:1. Double-click the Citrix Program Neighborhood icon placed on the desktop by the
Citrix install program.
2. Click the Settings icon or select Application Set Settings from the File menu.
3. Select the Default Options tab.
4. Select something other than Seamless Window from the Window Size dropdown list.
Modifying your Security Policy You must modify your Security Policy to enable the new Citrix_ICA TCP and Citrix_ICA_Browsing UDP services. The Citrix_ICA service initializes the stateful inspection of the Citrix ICA protocol. The Citrix_ICA service is not included in the Any service of the Security Policy and must therefore be enabled in one of the following ways:
• In the Security tab add a rule to your Security Policy with the Citrix_ICA TCP service. Similarly, add a rule for the Citrix_ICA_Browsing service. Alternatively, you can add simply add the Citrix_metaFrame group, which incorporates both the Citrix_ICA TCP and Citrix_ICA_Browsing UDP services.
OR
1. Expand the TCP branch of the Services Tree. Double-click on the Citrix_ICA service. The TCP Service Properties - Citrix _ICA window is displayed.
2. Click Advanced. The Advanced TCP Service Properties window is displayed.
3. Check Match for Any to turn on the Citrix ICA protocol inspection without having to add a specific rule for the Citrix_ICA service (if the Any service is allowed).
Discovering Citrix ICA Application Names
Chapter 6 Managing Check Point QoS 157
Discovering Citrix ICA Application NamesIn order to discover the Citrix ICA application name, as defined by the Citrix Administrator, use Check Point QoS to snoop the wire and send logs (of type alert) to the SmartView Tracker, recording the Citrix ICA application name. The Citrix ICA application detection is turned off by default.
Advanced: If you want to reset the application detection cache in order to re log a Citrix ICA application on the wire even if it was logged in the past 24 hours use the following command line instruction:
fw tab -t fg_new_citrix_app -x
To Enable Citrix ICA Application Name Logging:1. Double-click on the gateway in the Network Objects Tree. The Check Point
Gateway - General Properties window is displayed.
2. Choose Logs and Masters > Additional Logging in the tree on the left side of the Check Point Gateway - General Properties window. The Additional Logging Configuration window is displayed.
Note - The frequency of recording an application name log (alert) is 24 hours.
Discovering Citrix ICA Application Names
158
FIGURE 0-23 Additional Logging Configuration Window
3. Check Detect new Citrix ICA application names to enable Check Point QoS to log the Citrix application names.
4. Click OK. Citrix ICA application name detection is enabled.
5. Create a Security Policy with a valid rule that uses the Citrix_ICA service.
6. Install the QoS and Security policies on the QoS Module and let it run for a period of time. See "Installing the QoS Policy" on page 82.
Note - The QoS policy content is irrelevant to the application detection feature.
Discovering Citrix ICA Application Names
Chapter 6 Managing Check Point QoS 159
7. View the QoS log entries using SmartView Tracker (the entries are of Type Alert and contain the Citrix ICA application names). Once you have the application names you can turn off the application detection, as well as define new Citrix TCP services to use in a QoS policy. For example:FIGURE 0-24 Record Details Window
To Disable Citrix ICA Application Name Logging:1. Double-click on the gateway in the Network Objects Tree. The Check Point
Gateway - General Properties window is displayed.
2. Choose Logs and Masters > Additional Logging in the tree on the left side of the Check Point Gateway - General Properties window. The Additional Logging Configuration window is displayed.
3. Uncheck Detect new Citrix ICA application names so that Check Point QoS will not log the Citrix application names.
4. Click OK. Citrix ICA application name detection is disabled.
5. Install the QoS Policy.
Note - It is a pre-requisite that the Citrix_ICA TCP be enabled in the Security Policy.
Defining a New Citrix TCP Service
160
Defining a New Citrix TCP ServiceA new service type was introduced in the Smart DashBoard, Citrix TCP.
To Define a New Citrix TCP Service1. Right-click on the Citrix TCP branch of the Services Tree, and select New Citrix
TCP. The Citrix Service Properties window is displayed.
2. Enter the following details in the Citrix Service Properties window, as shown in the example below:
• Name: The name of the new service.
• Comment: A comment describing the new service.
• Color: Select a color from the dropdown list.
• Application: The exact name (case insensitive) of the Citrix Application.FIGURE 0-25 Citrix Service Properties Window
3. Click OK to create the new Citrix Class of Service.
Note - The application name is case insensitive.
Adding a Citrix TCP Service to a Rule (Traditional Mode Only)
Chapter 6 Managing Check Point QoS 161
Adding a Citrix TCP Service to a Rule (Traditional Mode Only)
Once you have created a new Citrix TCP service, you can add the service to a rule in your QoS Policy, in the usual manner. See “Editing QoS Rule Bases” on page 118
Installing the Security and QoS PoliciesOnce you have created the appropriate Security and QoS Policies these must be installed.
Managing QoS for Citrix Printing
162
Managing QoS for Citrix PrintingIn This Section
Printing generates relatively large quantities of data, causing the TCP connection to consume excessive quantities of bandwidth. Clearly, from a QoS perspective this type of connection should be identified and the bandwidth made available to these connections should be limited.
There are three primary methods of printing in the MetaFrame environment, IP Network printing, MetaFrame Auto-Creation of printers and local MetaFrame printing.
Check Point QoS provides a solution for printing traffic using the MetaFrame Auto-Creation of printers printing method, by classifying each ICA connection as either a printing or a non-printing connection.
A connection that is classified as printing is assigned to a Citrix printing rule. This rule can be configured to limit printing traffic and thus avoid excessive consumption of bandwidth. A connection that is classified as non-printing is assigned to a rule according to the regular matching method.
Classification of the connection is dynamic and is based on examining the ICA priority bits of each packet. An ICA connection is therefore matched dynamically to one of 2 different rules depending on the type of data passing through the connection at any point in time.
It is recommended that you limit the bandwidth per connection for printing to 25Kbps. This value represents the average bandwidth utilization of a single non-printing Citrix ICA session versus an additional 150Kbps of bandwidth per session that printing often requires. This preserves bandwidth for other traffic.
Configuring a Citrix Printing Rule (Traditional Mode Only)
Define a printing rule to which all ICA connections that are in a printing state are assigned.
Configuring a Citrix Printing Rule (Traditional Mode Only) page 162
Configuring Check Point QoS Topology page 163
Configuring Check Point QoS Topology
Chapter 6 Managing Check Point QoS 163
To Configure a Citrix Printing Rule1. Position your cursor in the Name field of the QoS tab, at the position where you
want to add a new rule.
2. Right-click and select one of the Add Rule options. The Rule Name window is displayed.
3. Enter the rule name in the Rule Name field.
4. Click OK to save the rule name.
5. Right-click in the Service column and select Add. The Add Object window is displayed, listing the network objects defined in the Security Policy and the QoS Policy.
6. Select the predefined Citrix_ICA_printing service and click OK. The service is added to the rule.
7. Right-click in the Action column and select Edit Properties. The QoS Action Properties window is displayed.
8. Select Advanced in the Action Type area.
9. Select Per connection limit in the Limit area.
10. Enter a per connection limit of 25 Kbps in the Per connection limit field (recommended).
11. Click OK.
Configuring Check Point QoS TopologyWhen the MetaFrame Auto-Creation of printers printing method is used, the Citrix printing traffic passes from the Citrix Server to the Citrix Client. To enforce QoS on this traffic, Check Point QoS must be installed on the Gateway external interface on the inbound direction, or on the Gateway internal interface on the outbound direction, that is, Flood-Gate-1 must be able to "see" the traffic passing from the Citrix Server to the Citrix Client.
Viewing the Check Point QoS Modules Status
164
Viewing the Check Point QoS Modules Status
To Display the Status of Check Point QoS Modules Controlled by the SmartCenter Server
Use the Check Point SmartView Status application and the SmartView Monitor. For information about the Check Point SmartView Status, see the SmartCenter Administration Guide.
Enabling Log Collection
Chapter 6 Managing Check Point QoS 165
Enabling Log CollectionIn order for a connection to be logged, the QoS logging flag must be turned on and the connection’s matching rule must be marked with either Log or Account in the Track field of the rule. For further information on how Check Point QoS’s logging features work see “Overview of Logging” on page 170.
In This Section
To Turn on QoS LoggingA QoS Module logs to the Check Point log if Turn on QoS Logging is checked in the Additional Logging page (under Logs and Masters) of the QoS Module’s Properties window (Figure 6-4 on page 166). By default Qos Logging is turned on.
To Turn on QoS Logging page 165
To Confirm that the Rule is Marked for Logging page 166
To Start SmartView Tracker page 167
To Confirm that the Rule is Marked for Logging
166
Figure 6-4 Properties Window - Additional Logging Configuration
To Confirm that the Rule is Marked for Logging1. Select the rule whose connection will be logged.
2. Confirm that either Log or Account appear in the Track field. See “To Modify Tracking for a Rule” on page 135
Figure 6-5 Track Logging or Accounting
To Start SmartView Tracker
Chapter 6 Managing Check Point QoS 167
To Start SmartView TrackerTo start SmartView Tracker, double-click on the SmartView Tracker icon, or choose
SmartView Tracker from the Window menu in the SmartDashboard window.Figure 6-6 Log showing FloodGate-1 Entries
It is now possible to view log data according to:
• Rule Name
• Rules using DiffServ
• Control type having to do with install and uninstall logs
For more information, see “SmartView Tracker” in the SmartCenter Administration Guide.
Note - The SmartCenter Server reads the Log File and sends the data to the SmartConsole for display. The SmartConsole only displays the data.
To Start SmartView Tracker
168
169
Chapter 7SmartView Tracker
In This Chapter
Overview of Logging page 170
Examples of Log Events page 174
Examples of Account Statistics Logs page 177
Overview of Logging
170
Overview of LoggingThe SmartView Tracker enables you to view entries in the Log File. Each entry in the Log File is a record of an event or an account record. The SmartView Tracker gives you control over the information displayed in the Log File. You can navigate through the Log File and select the log entries that you would like to display. You can view the log entries for all the installed Check Point products or for a selected product, such as Check Point QoS or VPN.
Two types of events are logged. Table 7-1 on page 171 describes the features unique to event logs and Table 7-1 on page 173 describes the features unique to accounting logs.
The following two conditions must be met for a connection to be logged:
• The QoS logging checkbox must be selected in the Gateway Properties - Additional Logging Configuration window shown in Figure 6-4 on page 166 must be selected. (By default this is automatically selected.)
• The connection’s matching rule must be marked with either Log or Account in the Track field of the rule. Refer to “To Confirm that the Rule is Marked for Logging” on page 166 and “To Modify Tracking for a Rule” on page 135.
Further information on how to start the SmartView Tracker can be found in “Enabling Log Collection” on page 165.
Overview of Logging
Chapter 7 SmartView Tracker 171
The following table describes the non-accounting events logged by SmartView Tracker:
Table 7-1 SmartView Tracker Non-Accounting Log Events
Log Event Data Returned Presentation Express or
Traditional
modes
Connection Reject
QoS rejects a connection when the number of guaranteed connections is exceeded and/or when you have configured the system not to accept additional connections.
The name of the matching rule on account of which the connection was rejected.
Generated as a reject log. Unified with the initial connection log.
Traditional mode only. PCG is a feature of Traditional mode.
Running Out of Packet Buffers
Overview of Logging
172
• QoS’s global packet buffers are exhausted.
• One of the interface-direction’s packet buffers is exhausted. A report is generated a maximum of once per 12 hours.
A string explaining the nature of the problem and the size of the relevant pool.
New log record created each time a global problem is reported.
Traditional mode only.
LLQ Packet Drop
When a packet is dropped from an LLQ connection. A report is generated a maximum of once per 5 minutes.
The statistics are computed from the last time an LLQ Packet Drop log was generated for all relevant interface directions. The following are logged:8. number of bytes
dropped from the connection.
9. average delay computed for all the connection’s packets that were not dropped.
10. maximum delay of a connection packet.
11. maximum delay difference between two consecutive successfully transmitted packets.
Unified with the initial connection log.
Traditional Mode only. LLQ is a feature of Traditional mode.
Table 7-1 SmartView Tracker Non-Accounting Log Events
Log Event Data Returned Presentation Express or
Traditional
modes
Overview of Logging
Chapter 7 SmartView Tracker 173
Table 7-1 Explaining the Accounting SmartView Tracker Log
Table 7-2
Logged Data Returned Express or Traditional
modes
General Statistics
The total bytes transmitted through QoS for each relevant interface and direction.
Inbound & outbound bytes transmitted by Check Point QoS.
Both
Drop Policy Statistics
• Total bytes dropped from the connection as a result of QoS’s drop policy.
• Count of the bytes dropped from the connection because the maximum used memory fragments for a single connection was exceeded
Traditional Mode only
LLQ Statistics
Statistics about the LLQ connection.
The following are logged:8. number of bytes
dropped from the connection due to delay expiration
9. average packet delay.
jitter which is computed as the maximum delay difference between two consecutive packets.
Traditional Mode only. LLQ is a feature of Traditional mode.
Examples of Log Events
174
Examples of Log EventsIn This Section
This section describes the log events in the SmartView Tracker:
Connection Reject LogThe connection is rejected because the rule exceeds the number of guaranteed connections, where Accept additional non guaranteed connections is unchecked in the QoS Action Properties window (see “QoS Action Properties” on page 47). The log will include the name as well as the class of the rule in the following format: rule_name:<class>-><name>.
In the following example, the rule belongs to the class Best_Effort. The name of the rule (rule_name) is udp2.
LLQ Drop LogWhen a packet from the LLQ connection is dropped, LLQ information is computed and logged from the last time a log was generated. This information includes significant data logged from the relevant interface-direction. In the following example, the information logged includes:
• s_in_llq_drops: The number of bytes dropped from the connection on the Server-In interface direction.
Connection Reject Log<ManRef>page 174
LLQ Drop Log<ManRef>page 174
Pool Exceeded Log<ManRef>page 175
Table 7-1 Connection Reject Log — Example
..
.
Time Product Interface Type Action Information ...
..
.15:17:09
QoS daemon
log reject
rule_name:Best_Effort->udp2
...
Pool Exceeded Log
Chapter 7 SmartView Tracker 175
• s_in_llq_avg_xmit_delay: The average delay computed for all the connection's packets that were not dropped on the Server-In interface direction.
• s_in_llq_max_delay: The maximum delay of a connection packet that was not dropped on the Server-In interface direction.
• s_in_llq_xmit_jitter: The maximum delay difference between two consecutive successfully transmitted packets of the connection on the Server-In interface direction. Any packets which are dropped in between the two successfully transmitted packets are ignored.
• s_in_llq_recommended_delay: The default delay that can be entered into the Add Low Latency QoS Class Properties window in order to achieve a minimal number of dropped bytes.
Table 7-2 LLQ Drop Log — Example
In the above example relevant data was observed only on the Server-In interface direction, therefore only Server-In counters are available.
Pool Exceeded Log The designated size of the pool is exceeded, whether the pool is set for a particular interface direction, or whether it represents the global pool. In the following example, the information logged includes:
• an interface direction (ifdir) has a pool size of 8 fragments
Table 7-3
... Product Type Information ...
... QoS log s_in_llq_drops:3000 s_in_llq_avg_xmit_delay: 900 s_in_llq_max_delay: 1351 s_in_llq_xmit_jitter: 1351s_in_llq_recommended_delay:2000
...
Note - There are several reasons why logging might not occur on a specified interface direction:
• QoS might not be installed on all the interfaces directions.• No packets were seen on other interface directions.• Data on other interface directions might not be significant, for instance, the
values logged might be all zeroes.
Pool Exceeded Log
176
• the interface name is E100B1, and the direction is outbound (marked by little cube juxtaposed to the interface name which has an outward pointing arrow) in the Inter. column.
Table 7-4 Pool Exceeded Log — Example
Table 7-5
..
.
Product Interface Type Information ...
..
.QoS E100
B1contr
olinfo:Ifdir Memory Pool Exceeded Pool_size:8
...
Examples of Account Statistics Logs
Chapter 7 SmartView Tracker 177
Examples of Account Statistics LogsIn the Check Point SmartView Tracker, the account logs always include the segment_time information (the time from which the information about the log was gathered) in the Information column.
Table 7-6 The Mandatory Fields in Account Logs
In This Section
Account Logs may include any or all of the above information:
General Statistics DataThese statistics include the number of bytes transmitted through QoS in any relevant interface direction. In the following example:
• s_in_bytes: 5768 bytes were transmitted through Check Point QoS on the Server-In interface direction.
• s_out_bytes: 154294 bytes were transmitted through Check Point QoS on the Server-Out interface direction.
Table 7-7
... Product Type Information ...
... QoS Account segment_time 8May2002 12:24:57 ...
General Statistics Data page 177
Drop Policy Statistics Data page 178
LLQ Statistics Data page 178
Note - Only significant data is logged and presented in the same log record.
Drop Policy Statistics Data
178
Table 7-8 General Statistics Data — Example
Drop Policy Statistics DataThe number of bytes dropped from the connection in any relevant interface direction as a result of drop policy are logged. The drop policy is aimed at managing FloodGate-1 packet buffers, see “WFRED (Weighted Flow Random Early Drop)” on page 32. This includes the total number of bytes dropped from the connection since it exceeded its allocation. In the following example:
• s_out_total_drops: 3914274 bytes were dropped from the connection as a result of drop policy, on the Server-Out interface direction.
• s_out_exceed_drops: Out of total number of drops (s_out_total_drops) 3914274 bytes were dropped from the connection because it exceeded its allowed number of fragments, on the Server-Out interface direction.
Table 7-10 Drop Policy Statistics Data — Example
LLQ Statistics Data Data items are the same as in “LLQ Drop Log” on page 174, but are computed from the beginning of the connection and not from the last time a log was generated.
Table 7-9
... Information ...
... s_in_bytes:5768 s_out_bytes: 154294
...
Table 7-11
... Information ...
... s_out_total_drops:3914274 s_out_exceed_drops: 3914274
...
179
Chapter 8Command Line Interface
In This Chapter
Check Point QoS Commands page 180
Setup page 181
fgate Menu page 182
Control page 183
Monitor page 185
Utilities page 187
Check Point QoS Commands
180
Check Point QoS CommandsTable 8-1 lists the QoS command names.
Table 8-1 FloodGate-1 Command Names
VPN-1 Power and FloodGate-1
Installed on the Same Machine
Description
etmstart Starts FloodGate-1
etmstop Stops FloodGate-1
fgd50 FloodGate-1 daemon
Setup
Chapter 8 Command Line Interface 181
SetupIn This Section
cpstart and cpstopGenerally, to stop and start the QoS Module you are required to stop the VPN-1 Power using the cpstop and cpstart commands. In the event that you would like to stop the QoS Module only, you can use the QoS specific etmstart and etmstop commands. For more on cpstop and cpstart, see the SmartCenter Administration Guide.
etmstartetmstart loads the FloodGate-1 Module, starts the FloodGate-1 daemon (fgd50), and retrieves the last policy that was installed on the FloodGate-1 module.
etmstopetmstop kills the FloodGate-1 daemon (fgd50) and then unloads the FloodGate-1 policy and Module.
cpstart and cpstop page 181
etmstart page 181
etmstop page 181
fgate Menu
182
fgate MenuThe following menu is displayed when typing fgate from the command line.Figure 8-1 fgate Menu
Control
Chapter 8 Command Line Interface 183
ControlIn This Section
fgateThe fgate program is used to manage FloodGate-1. Its specific action is determined by the first command line argument, as described in the following sections:
fgate loadfgate load runs a verifier on the policy file. If the policy file is valid, fgate compiles and installs a QoS Policy to the specified QoS Modules. It can only be run from the SmartCenter Server.
Syntax
If targets is not specified, the QoS Policy is installed on the local host.
fgate unloadfgate unload uninstalls a QoS Policy from the specified QoS Modules. It can only be run from both the SmartCenter Server and localhost.
Syntax
If targets is not specified, the QoS Policy is uninstalled from the local host.
fgate fetchfgate fetch retrieves the QoS Policy that was last installed on the local host. You must specify the machine where the QoS Policy is found. Use “localhost” in case there is no SmartCenter Server or if the SmartCenter Server is down. You may specify a list of SmartCenter Servers, which will be searched in the order listed.
fgate page 183
fgate load page 183
fgate unload page 183
fgate fetch page 183
fgate load <rule-file.F> [targets]
fgate unload [targets]
Control
184
fgate fetch -f attempts to retrieve policies from all management stations, one after the other until it succeeds. If the module fails to retrieve a policy from a SmartCenter Server, it tries to retrieve one from itself.
Syntax
Examples
fgate fetch [-f | servers]
fgate fetch localhostfgate fetch -ffgate fetch mgmt_server_name
Monitor
Chapter 8 Command Line Interface 185
MonitorIn This Section
fgate statfgate stat displays the status of target hosts in various formats. If this command is launched from a SmartCenter server this command can be run on an array of modules. If this command is launched from a module, the status of the module is returned.
Usage
The default format displays the following information for each host: product, version, build number, policy name (Express or Traditional), install time and interfaces number.
If no target is specified, the status of localhost is shown. Example:
fgate stat page 185
fgate ver page 186
fgate stat [targets]
fgate stat
Monitor
186
Figure 8-2 fgate stat Output
Examples
fgate verfgate ver displays the FloodGate-1 version number. If the -k option is included, both the kernel version build number and QoS executable version build number are returned. Without the -k, only the QoS executable version is specified.
Syntax
fgate statfgate stat gateway1 gateway2
fgate ver [-k]
Utilities
Chapter 8 Command Line Interface 187
UtilitiesIn This Section
fgate logfgate log turns logging on or off in the kernel. It can be used in order to save resources without reinstalling your QoS policy. the stat option returns the current state of logging.
Syntax
By default, fgate log is turned on.
fgate ctlfgate ctl sends control information to the QoS kernel module.
Syntax
fgate debugfgate debug turns on a debug flag which sends additional debugging information to the fgd logfile: $FGDIR/log/fgd.elg. The default is off.
fgate log page 187
fgate ctl page 187
fgate debug page 187
fgate kill page 188
fgate log < on | off | stat >
fgate ctl etmreg
parameter meaning
etmreg etmreg is for Unix platforms only. fgate ctl turns on or off the QoS kernel.
Utilities
188
Syntax
fgate killfgate kill sends a signal to a FloodGate-1 daemon. The SmartCenter Server does not run the QoS daemon therefore this command is valid only on modules.
Syntax
The FloodGate-1 daemon writes the pids to files in the log directory upon startup. These files are named $FWDIR/tmp/<daemon_name>.pid. For example, the file containing the pid of the FloodGate-1 snmp daemon is $FWDIR/log/snmpd.pid.
Examples
The following command:
sends signal 15 to the FloodGate-1 fgd daemon.
The following command:
sends signal 1 to the FloodGate-1 fgd daemon.
fgate debug < on | off >
fgate kill [-t sig_no] proc-name
parameter meaning
[-t sig_no] proc-name If the file$FWDIR/tmp/<proc-name>.pid exists, send sig_no to the pid given in the file.If no signal is specified, signal 15 (SIGTERM) is sent.
fgate kill fgd
fgate kill -t 1 fgd
189
Chapter 9Check Point QoS FAQ (Frequently Asked Questions)
In This Chapter
Questions and Answers page 190
Questions and Answers
190
Questions and AnswersIn This Section
IntroductionWhat is Check Point QoS? — Check Point QoS is a policy-based, Quality of Service (QoS) solution for VPNs, private WANs and Internet links. It optimizes network performance by assigning priority to business-critical applications and end users. Check Point QoS is tightly integrated with VPN-1® Pro
How can I comment on this FAQ? — For comments and ideas regarding this FAQ or Check Point QoS in general, please send email to: [email protected]
For additional technical information about Check Point QoS, consult Check Point’s SecureKnowledge database athttp://support.checkpoint.com/kb/
Where can I find further information regarding Check Point QoS? — Find further details about Check Point QoS at http://www.checkpoint.com/products/floodgate-1/index.html
Do I have to know how to administrate Provider-1/SiteManager-1 to manage Check Point QoS? — Knowing how to administrate Provider-1/SiteManager-1 is not mandatory, but prior knowledge of Provider-1/SiteManager-1 is helpful when working with Check Point QoS.
Introduction page 190
Check Point QoS Basics page 191
Other Check Point Products - Support and Management page 194
Policy Creation page 195
Capacity Planning page 196
Protocol Support page 197
Installation/Backward Compatibility/Licensing/Versions page 198
How do I? page 198
General Issues page 199
Check Point QoS Basics
Chapter 9 Check Point QoS FAQ (Frequently Asked Questions) 191
Check Point QoS BasicsWhen should I use Traditional mode and when should I use Express mode? —
Traditional mode should be used if you need fine-tuned functionality and enhanced Check Point QoS features. Express mode should be selected if your system requires only basic QoS.
What are the benefits of using each mode? — Traditional mode provides you with optimal QoS functionality, whereas Express mode increases performance and needs less CPU and less memory.
Can I change from Express mode to Traditional mode and vice versa? — You can change a policy from Express mode to Traditional mode, however, you cannot change a policy from Traditional mode to Express mode. Therefore it is recommended that if you are unsure which to install, you should begin with Express mode, maintaining the option to transition to Traditional mode, if you find that your policy required heightened Check Point QoS functionality.
What is the highest weight I can use in a rule? — Weights are relative. The only limitation is the Maximum weight of rule parameter, which is defined in the Global Properties window under Check Point QoS. The default parameter is 1000, but can be changed to any number.
In the example shown in Table 9-1, you can see the significance of the value of the weight allocated in two different policies. In the example both the HTTP and FTP connections initially enjoy an equal share of the available bandwidth, although they each had a weight of 500 in Policy 1 and a weight of 2 in Policy 2.
By adding a third rule to both policies you can significantly change the result. for example, An SMTP connection with a weight of 100 can be added to each policy. Due to the high initial weights used in Policy 1, there is an insignificant change to the amount of bandwidth available for the HTTP connection in Policy 1 + third rule. However, due to the low initial weights used in Policy 2, the amount of bandwidth that is available to the HTTP connection in Policy 2 + third rule is significantly reduced.
Note - This parameter is only used to assist in input validation.
Check Point QoS Basics
192
Table 9-1 Example of Highest Weight Differentiation
Should I install Check Point QoS on the external or the internal interface? — While Check Point QoS can run on both interfaces, it is highly recommended to position Check Point QoS on the external interface only.
What is the difference between guarantees and weights? — Guarantees and weights are similar in their behavior. Despite the difference in their dictionary meaning, they both guarantee the allocated bandwidth to the matched traffic. The differences between them are:
Policy 1 HTTP gets ...and
equals
Comment
HTTP weight = 500, FTP weight =500
500/(500+500) = ½ Equal weight is given to each rule.
Policy 2
HTTP weight = 2, FTP weight =2;
2/(2+2) = ½ Equal weight is given to each rule.
Policy 1 + third rule
HTTP weight = 500, FTP weight =500, SMTP weight = 100
500/(500+500+100)
= 500/1100
Due to the initial high value of the weights in Policy 1, the amount of bandwidth available to the HTTP connection is only marginally less than in Policy 1 even after the introduction of the third rule.
Policy 2 + third rule
HTTP weight = 2, FTP weight =2; SMTP weight = 100
2/(2+2+100) = 2/104 Due to the low value of the weights in Policy 2, the amount of bandwidth available to the HTTP connection is now significantly less as a result of the introduction of the third rule.
Check Point QoS Basics
Chapter 9 Check Point QoS FAQ (Frequently Asked Questions) 193
• Guarantees are stated in absolute numbers (for example, 20000bps) and weights are stated in relative numbers (for example, 100).
• Guarantees are allocated their share of bandwidth before weights. For example if you have a link of 1.5 MB:
Your Rule Base is:
• HTTP Guarantee 1Mb
• FTP Weight 40
• SMTP Weight 10
The result is:
• first 1 MB for HTTP is allocated, then• 0.4 MB for FTP is allocated and 0.1MB for SMTP is allocated.
Use guarantees to define bandwidth in absolute terms or for per connection guarantees.
How does Check Point QoS handle TCP retransmitted packets? — When a retransmission is detected, Check Point QoS checks to see if the retransmitted data is already contained in the Check Point QoS queue. If so, the packet is dropped. This unique Check Point QoS capability eliminates retransmissions that consume up to 40% of a WAN link, and saves memory required to store duplicated packets.
Which Firewall resources does Check Point QoS support in the Rule Base? — Check Point QoS can use its resources to inspect HTTP traffic. Resources are defined using the URI for QoS option and can contain specific URLs or files. For example, you can limit Web surfing to the site http://www.restrict-access-to-this-site.com. You need to add a QOS URI resource that looks for the string “www.restrict-access-to-this-site.com” (without http://). Then use the resource in a Check Point QoS rule and add a limit.
Do guarantees waste bandwidth? — No. Check Point QoS uses a sophisticated queuing mechanism. An application only takes as much bandwidth as it needs. Any unused bandwidth is then available for use by other applications.
How do I know if loaned bandwidth is available for applications that may need it back? — There is no loaned bandwidth in Check Point QoS. Bandwidth that is not utilized by a guarantee/weighted rule is immediately (on a per-packet basis) distributed to the other connections, according to their relative priorities. The important thing to remember is Resolution (referring to level of granularity). Check Point QoS allocates bandwidth on a per packet basis. Therefore, only one packet is allocated at a time, resulting in the most accurate scheduling policy.
Other Check Point Products - Support and Management
194
Other Check Point Products - Support and Management
Where is Check Point QoS placed in the Provider-1/SiteManager-1 Inspection chain? — Check Point QoS is composed of two Modules:
• QoS Policy, which is in charge of rule matching
• QoS Scheduling, which is in charge of packet scheduling
Does Check Point QoS work With Provider-1/SiteManager-1? — Yes. One of Check Point QoS’s most important features is its unique and sophisticated integration with Provider-1/SiteManager-1. Its integration features include:
• accurate classification of VPN traffic (inside the VPN tunnel)
• classification of NATed traffic
• shared network objects and topology (that save you time and effort in administration)
• common Check Point SmartDashboard with an advanced GUI but a familiar look and feel
• authenticated Quality of Service allows you to assign bandwidth to VPN remote users
• DiffServ Support and Check Point QoS bring Better than Frame Relay QoS to the VPN world
• log verification
Is SmartView Monitor a part of Check Point QoS? — No. As of NG with Application Intelligence (R55), SmartView is a separate product that is bundled with Check Point QoS.
Does Check Point QoS support Load Sharing configurations? — Yes, Check Point QoS supports all ClusterXL configurations. Check Point QoS supports the SYNC mechanism and therefore can be used with CPLS/CPHA or third-party solutions. For OPSEC partner solutions, see the OPSEC Website:
http://www.opsec.com/ for certification.
Does Check Point QoS support NATed traffic? — Check Point QoS has full support for NATed traffic, including matching, scheduling, limiting and all other Check Point QoS features.
What is the maximum number of QoS Modules I can manage? — QoS Modules management is identical to VPN/FireWall Module management. Thus, the maximum number of Modules is identical to the maximum number of VPN/FireWall Modules that are managed.
Policy Creation
Chapter 9 Check Point QoS FAQ (Frequently Asked Questions) 195
Do I need to run QoS on the SmartCenter server? — Yes, in order to manage a QoS Module you need to install Check Point QoS on the SmartCenter server.
Policy CreationWhen should I use LLQ (Low Latency Queuing)? — LLQ is best suited for VoIP applications, Video conferencing and other multimedia applications. LLQ is targeted for applications where:
• a minimal guaranteed bandwidth is required for adequate performance
• low delay and Jitter are required
Is QoS Rule Base “first match”? — From Check Point QoS NG forward, all QoS rules are matched on the “first match” principle. Meaning that only the first rule that applies to a connection is activated.
For example, if you have a rule for CEO traffic and a rule for HTTP traffic, the rule that appears first within the Rule Base will be matched to all CEO surfing.
Correct Rule Base (CEO is the first match)
1. SRC=CEO => Guarantee = 128Kbps
2. Service=HTTP => Limit = 64Kbps
Incorrect Rule Base (CEO traffic will be limited)
1. Service=HTTP => Limit = 64Kbps
2. SRC=CEO => Guarantee = 128Kbps
I am using QoS on multiple modules. What is the best way to organize my Rule Base? — • If you are managing Modules with identical bandwidth and you want an
identical policy for all Modules, define as All in the Install On field.
• If you are managing Modules with varied bandwidths and want an identical policy for all Modules, you can have one policy installed on all modules. It is best to use weights since they assign relative bandwidth and not a fixed one. Remember that weights also guarantee bandwidth allocation.
• If you are managing Modules with varied bandwidths and want a different policy for all Modules, you can use different sub-rules for each module. You can also use common rules that are matched for Modules.
When should I use Sub-rules? — Sub-rules should be used when there is hierarchy between objects. For example, when you want to manage bandwidth according to organizational structure, such as within an organization that has R&D, Marketing and operation divisions.
Capacity Planning
196
How can I see the top bandwidth-hogging applications? — From the command line run the command rtmtopsvc.
Capacity PlanningWhat are Check Point QoS’s memory requirements? — To run Check Point QoS, the following amount of free memory is needed (in addition to the memory needed for Provider-1/SiteManager-1):
• These numbers include SmartView Monitor and UserAuthority.
• Connections are counted in the Firewall connection table.
• Note that the default size for the connection table is 25,000.
• On an average, each connection requires 1300 bytes.
How do I know which machine I need to run Check Point QoS? — Deciding on a hardware platform and vendors involves many aspects and each buyer has their own specific considerations such as support, price, appliances, knowledge, and so on.
As far as performance is concerned, CPU performance is the main factor in Check Point QoS performance. With Check Point QoS’s reduced memory footprint and 2003 memory prices, memory should not usually be the cause of a bottleneck.
How do I tune Check Point QoS performance? — Here are some tips on fine-tuning Check Point QoS performance:
1. Upgrade to the newest Check Point QoS version available. Major improvements in performance have been introduced in Check Point QoS NG FP1 and NG FP2.
2. In most cases you need to install Check Point QoS only on the external interfaces of the gateway.
Figure 9-1 Check Point QoS memory requirements
Number of
connections
Manageme
nt
Module (or Management+ Module)
5,000 0 MB 32.5 MB
10,000 0 MB 39 MB
25,000 0 MB 57 MB
50,000 0 MB 91 MB
100,000 0 MB 156 MB
Protocol Support
Chapter 9 Check Point QoS FAQ (Frequently Asked Questions) 197
3. Unless you are using limits for inbound traffic, installing Check Point QoS only in the outbound direction will provide you with most of the functionality and improvements.
4. Put more frequent rules at the top of your Rule Base. You can use SmartView Monitor to analyze how much a rule is used.
5. Turn “per connection limits” into “per rule limits”.
6. Turn “per connection guarantees” into “per rule guarantees”.
What is the maximum bandwidth supported by Check Point QoS? — Check Point QoS NG FP1 can support up to 1.13MBps and 890MBps (in Traditional Mode) of traffic of long UDP packets. In real-world traffic and in the Rule Base, Check Point QoS supports 330MBps (In Express Mode) and 255 MBps (in Traditional Mode) of traffic.
Protocol SupportWhat protocols/services are supported by Check Point QoS? — See: http://www.checkpoint.com/products/downloads/vpn-1_fw-1_fg-1_app_support.pdf
Can I prioritize system administration traffic? — Yes. This can be done in any of the following ways:
• Guarantees for administrators based on authentication
• Guarantees for administrators based on IPs, networks
• Guarantees for applications only administrators use (for example, Provider-1/SiteManager-1 control protocols, PC-Anywhere)
• Combinations of all the above
Does Check Point QoS support Citrix applications? — Yes, Citrix applications can be differentiated from one another. In addition, Check Point QoS can identify Citrix ICA printing traffic and re-classify it to a proper rule.
Does Check Point QoS support SIP? — Yes. Starting from Check Point QoS FP2, the SIP protocol is supported.
Does Check Point QoS support H323? — Yes. Starting from Check Point QoS FP1, the H323 protocol is supported
Does Check Point QoS support GRE? — Yes. This protocol is supported.
Note - New services and applications are added on a permanent basis.
Installation/Backward Compatibility/Licensing/Versions
198
Installation/Backward Compatibility/Licensing/Versions
When will Check Point QoS next feature pack be available? — Check Point QoS feature packs/releases are usually shipped at the same time Provider-1/SiteManager-1 feature packs are released.
How do I?How do I guarantee performance for my mail server? — You need to add a rule matching your email traffic. You can do this by either matching the source/destination of your mail server, or matching mail protocols (SMTP, POP3, Exchange). For this rule, define a weight or guarantee that meets the needs of the priorities you want to set.
How do I ensure Quality of Service for Voice Over IP? — Check Point QoS FP1 introduced the VoIP-tuned mechanism Low Latency Queuing (LLQ). This mechanism is tuned to achieve best latency for constant bit rate applications, like VoIP.
To limit the number of connections admitted, use LLQ with a per connection guarantee. For voice, you want to give each conversation a guaranteed bandwidth. Usually you would want an admission policy that does not accept additional calls if bandwidth is not adequate.
How can I prioritize traffic for remote users? — Using the Authenticated QoS feature of Check Point QoS, you can prioritize bandwidth allocation for remote VPN users and Windows domain user groups. To configure the Windows domain users please refer to the UserAuthority Administration Guide and read the SecureAgent -> System Setup section.
How do I guarantee performance for my ERP applications? — You need to add a rule matching your ERP traffic. You can do this by either matching the source/destination of your ERP server, or matching application protocols (SAP, BAAN, ORACLE). For this rule, define a weight or guarantee that meets the needs of the priorities you want to set. If your ERP application is not a predefined service, you can either add it manually or use the first method.
If you are using ERP over HTTP, check “How can I provide bandwidth for my intranet applications”?
Note - This is equivalent to the busy tone in old voice system.
General Issues
Chapter 9 Check Point QoS FAQ (Frequently Asked Questions) 199
Can I use Check Point QoS to prevent Denial of Service Attacks? — Check Point QoS’s main goal is not an Anti-Denial of Service tool. However, there are many situations in which Check Point QoS can be used to detect, monitor and prevent such attacks. Using SmartView Monitor and Check Point QoS you can perform detection and monitoring.
Prevention can be achieved in the following ways:
• by limiting applications that are known to be a part of DOS attacks (for example, ICMP, suspicious URLs).
• by providing guarantees for important traffic (for example, ERP, MAIL, VoIP).
• by providing guaranteed bandwidth for authenticated users using Authenticated QoS. Authenticated users can be identified with digital signatures and can rely on VPN authentication and encryption. Check Point QoS guarantees that these users will get their bandwidth. The attacker cannot authenticate to the VPN and will not get bandwidth for the attack.
Why is limiting bandwidth for Napster better than blocking It? — Blocking "nonwork-related" applications might cause users to find a way to bypass blocking. Prioritizing bandwidth lets users continue with their activities without damaging critical business processes. Consider a university where the Internet connection is being used for peer-to-peer file downloads like Napster and Kazaa. Blocking these services completely may encourage the students find a smart way to bypass the block, which in turn might cause legal problems. Check Point QoS offers smarter solutions:
• Limiting the allocated bandwidth for such applications – this can be done with or without the students’ knowledge.
• Limiting the allocated bandwidth during daytime, and providing more bandwidth at night.
• Providing guarantees to important users (Professors, MIS) while allowing students to use the reminder of the bandwidth.
General IssuesMy machine is experiencing certain technical failures. What should I do? — Check the Web for updated release notes on known issues and limitations. Contact your vendor for further support.
General Issues
200
I set up a guarantee/limit but in SmartView Monitor it seems to be broken? — If you are looking at very low traffic limit (for example, 1000 Bytes per second) at a high frequency (update every 2 seconds) it might look, as if the limit is broken since Check Point QoS does not fragment packets. If you lower the sampling frequency of SmartView Monitor (update every 8 seconds) you will see that limits are kept.
Can Check Point QoS prompt a user for authentication in order to use the Authenticated QoS feature? — No. In order to use Authenticated QoS, Provider-1/SiteManager-1 must perform an authentication session prior to the classification of the connection by Check Point QoS.
Can I deploy Check Point QoS on LAN environments? — Yes. You will need to position the hardware to support the network traffic you want to prioritize. Check Point QoS is best deployed in congestion points for network traffic.
What happens if a line’s bandwidth (as defined in the QoS tab of the Interface Properties window) is less than its physical (“real”) bandwidth? — Check Point QoS will only allocate as much bandwidth as is defined in the Interface Properties window. Additional bandwidth will not be allocated regardless of the physical bandwidth of the interface.
What happens if a link bandwidth (of the link defined in Check Point QoS) is more than its physical (“real”) bandwidth? — Check Point QoS will attempt to transmit more than the physical bandwidth allows. This can cause random traffic drops in the next hop that result in the loss of critical packets.
201
Chapter 10Deploying Check Point QoS
In This Chapter
Deploying Check Point QoS page 202
Sample Bandwidth Allocations page 204
Deploying Check Point QoS
202
Deploying Check Point QoS
Check Point QoS Topology RestrictionsCheck Point QoS can manage up to the maximum number of external interfaces supported by Firewall, subject to the following restrictions. (Refer to the Firewall documentation for further information):
1. All of the traffic on a managed line must go through the gateway.
2. Each managed line must be connected (directly or indirectly via a router) to a separate physical interface on the QoS machine. Two managed lines may not share a physical interface to the QoSmachine, nor may two lines be connected to the same router.
For example, in the configuration depicted in Figure 10-1, the routers can pass traffic to each other through the hub without the QoS Module being aware of the traffic.
Figure 10-1 Two Lines Connected to a Single Interface
In addition, you cannot manage two lines connected to a single router (as in Figure 10-2), since traffic may pass from one line to the other directly through the router, without the QoS Module being aware of the traffic.
Check Point QoS Topology Restrictions
Chapter 10 Deploying Check Point QoS 203
Figure 10-2 Two Lines Connected to a Router
An example of a correct configuration is depicted in Figure 10-3.Figure 10-3 Correct Configuration
Sample Bandwidth Allocations
204
Sample Bandwidth Allocations
Frame Relay NetworkIn the network depicted in Figure 10-4, the branch offices communicate with the central site and vice versa, but they do not communicate directly with each other or with the Internet except through the central site. The Web server makes important company documents available to the branch offices, but the database server supports the company’s mission-critical applications.
The problem is that most of the branch office traffic is internal and external Web traffic, and the mission-critical database traffic suffers as a result. The network administrator has considered upgrading the 56K lines, but is reluctant to do so, not only because of the cost but also because upgrading would probably not solve the problem. The upgraded lines would still be filled mostly with Web traffic.Figure 10-4 Frame Relay Network Example
The goals are as follows:
1. Allocate the existing bandwidth so that access to the database server gets the largest share.
2. Take into account that the branch offices are connected to the network by 56K lines.
Frame Relay Network
Chapter 10 Deploying Check Point QoS 205
These goals are accomplished with the following Rule Base:
Each office has sub-rules, as follows:.
The sub-rules give database traffic priority over Web traffic and other traffic.
AssumptionsThe following assumptions are made in this example:
• The problem (and its solution) apply to traffic outbound from the central site.
Note that FloodGate-1 shapes the branch office lines in the outbound direction only. FloodGate-1 shapes inbound traffic only on directly controlled interfaces (that is, interfaces of the FloodGated machine).
• The central site has the capacity to handle the network’s peak traffic load.
Table 10-1 Main Rules
Rule Name Source Destination Service Action
Office 1 Office 1 Any Any Weight 10Limit 56KBps
... ... ... ... ...
Office n Office n Any Any Weight 10Limit 56KBps
Default Any Any Any Weight 10
Table 10-2 Office Sub-Rules
Rule Name Source Destination Service Action
Start of Sub-Rule
Database Rule
Any Database Server
database-service Weight 50
Web Rule Any Web Server http Weight 10
Branch Offices
Any Any Any Weight 10
End of Sub-Rule
Frame Relay Network
206
• There is no traffic between the offices.
207
Appendix ADebug Flags
Note - Error is turned on by default.
fw ctl debug -m FG-1 Error Codes for Check Point QoS
208
fw ctl debug -m FG-1 Error Codes for Check Point QoS
TABLE 0-1 fw ctl debug -m FG-1 Error Codes for Check Point QoS
Command
Line
Usage
All commands begin with: fw ctl debug -m FG-1...
driver Driver Attachment
error General Error Flag
chain Main Steps Of QoS Packet Processing
install For Future Use
pkt Packet recording mechanism
citrix Citrix processing
ls Load sharing
tcp TCP Retransmission Detection
sched Packet Scheduling
policy QOS Policy Rules Matching
url QOS URL Matching
dns DNS Related Messages
rtm SmartView Monitor Interaction
auth Authenticated QOS
log Logging
conn Connections Processing
drops Drop Policy
rates Reporting Rule/Connection Rates
dropsv Verbose Version Of Drop Policy
timers Timer Events
chainq Internal Chain Q Mechanism
llq Low Latency Queuing
fw ctl debug -m FG-1 Error Codes for Check Point QoS
Chapter A Debug Flags 209
verbose Used With Other Flags - Adds More Information
automatch Report Matching Process (Debug Version Only)
autosched Report Scheduling Process (Debug Version Only), a good way of reporting of rates on rules
TABLE 0-1 fw ctl debug -m FG-1 Error Codes for Check Point QoS
Command
Line
Usage
fw ctl debug -m FG-1 Error Codes for Check Point QoS
210
211
THIRD PARTY TRADEMARKS AND COPYRIGHTS
Entrust is a registered trademark of Entrust Technologies, Inc. in the United States and other countries. Entrust’s logos and Entrust product and service names are also trademarks of Entrust Technologies, Inc. Entrust Technologies Limited is a wholly owned subsidiary of Entrust Technologies, Inc. FireWall-1 and SecuRemote incorporate certificate management technology from Entrust.
Verisign is a trademark of Verisign Inc.
The following statements refer to those portions of the software copyrighted by University of Michigan. Portions of the software copyright © 1992-1996 Regents of the University of Michigan. All rights reserved. Redistribution and use in source and binary forms are permitted provided that this notice is preserved and that due credit is given to the University of Michigan at Ann Arbor. The name of the University may not be used to endorse or promote products derived from this software without specific prior written permission. This software is provided “as is” without express or implied warranty. Copyright © Sax Software (terminal emulation only).
The following statements refer to those portions of the software copyrighted by Carnegie Mellon University.
Copyright 1997 by Carnegie Mellon University. All Rights Reserved.
Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that copyright notice and this permission notice appear in supporting documentation, and that the name of CMU not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.CMU DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CMU BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
The following statements refer to those portions of the software copyrighted by The Open Group.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE OPEN GROUP BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
The following statements refer to those portions of the software copyrighted by The OpenSSL Project. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/).
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY * EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The following statements refer to those portions of the software copyrighted by Eric Young. THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Copyright © 1998 The Open Group.
212
The following statements refer to those portions of the software copyrighted by Jean-loup Gailly and Mark Adler Copyright (C) 1995-2002 Jean-loup Gailly and Mark Adler. This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
The following statements refer to those portions of the software copyrighted by the Gnu Public License. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
The following statements refer to those portions of the software copyrighted by Thai Open Source Software Center Ltd and Clark Cooper Copyright (c) 2001, 2002 Expat maintainers. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.GDChart is free for use in your applications and for chart generation. YOU MAY NOT re-distribute or represent the code as your own. Any re-distributions of the code MUST reference the author, and include any and all original documentation. Copyright. Bruce Verderaime. 1998, 1999, 2000, 2001. Portions copyright 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002 by Cold Spring Harbor Laboratory. Funded under Grant P41-RR02188 by the National Institutes of Health. Portions copyright 1996, 1997, 1998, 1999, 2000, 2001, 2002 by Boutell.Com, Inc. Portions relating to GD2 format copyright 1999, 2000, 2001, 2002 Philip Warner. Portions relating to PNG copyright 1999, 2000, 2001, 2002 Greg Roelofs. Portions relating to gdttf.c copyright 1999, 2000, 2001, 2002 John Ellson ([email protected]). Portions relating to gdft.c copyright 2001, 2002 John Ellson ([email protected]). Portions relating to JPEG and to color quantization copyright 2000, 2001, 2002, Doug Becker and copyright (C) 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, Thomas G. Lane. This software is based in part on the work of the Independent JPEG Group. See the file README-JPEG.TXT for more information. Portions relating to WBMP copyright 2000, 2001, 2002 Maurice Szmurlo and Johan Van den Brande. Permission has been granted to copy, distribute and modify gd in any context without fee, including a commercial application, provided that this notice is present in user-accessible supporting documentation. This does not affect your ownership of the derived work itself, and the intent is to assure proper credit for the authors of gd, not to interfere with your productive use of gd. If you have questions, ask. "Derived works" includes all programs that utilize the library. Credit must be given in user-accessible documentation. This software is provided "AS IS." The copyright holders disclaim all warranties, either express or implied, including but not limited to implied warranties of merchantability and fitness for a particular purpose, with respect to this code and accompanying documentation. Although their code does not appear in gd 2.0.4, the authors wish to thank David Koblas, David Rowley, and Hutchison Avenue Software Corporation for their prior contributions.
Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0
The curl license
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1996 - 2004, Daniel Stenberg, <[email protected]>.All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose
with or without fee is hereby granted, provided that the above copyright
notice and this permission notice appear in all copies.
213
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder.
The PHP License, version 3.0
Copyright (c) 1999 - 2004 The PHP Group. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. The name "PHP" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected].
4. Products derived from this software may not be called "PHP", nor may "PHP" appear in their name, without prior written permission from [email protected]. You may indicate that your software works in conjunction with PHP by saying "Foo for PHP" instead of calling it "PHP Foo" or "phpfoo"
5. The PHP Group may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number. Once covered code has been published under a particular version of the license, you may always continue to use it under the terms of that version. You may also choose to use such covered code under the terms of any subsequent version of the license published by the PHP Group. No one other than the PHP Group has the right to modify the terms applicable to covered code created under this License.
6. Redistributions of any form whatsoever must retain the following acknowledgment:
"This product includes PHP, freely available from <http://www.php.net/>".
THIS SOFTWARE IS PROVIDED BY THE PHP DEVELOPMENT TEAM ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE PHP DEVELOPMENT TEAM OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This software consists of voluntary contributions made by many individuals on behalf of the PHP Group. The PHP Group can be contacted via Email at [email protected].
For more information on the PHP Group and the PHP project, please see <http://www.php.net>. This product includes the Zend Engine, freely available at <http://www.zend.com>.
This product includes software written by Tim Hudson ([email protected]).
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd
214
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Copyright © 2003, 2004 NextHop Technologies, Inc. All rights reserved.
Confidential Copyright Notice
Except as stated herein, none of the material provided as a part of this document may be copied, reproduced, distrib-uted, republished, downloaded, displayed, posted or transmitted in any form or by any means, including, but not lim-ited to, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of NextHop Technologies, Inc. Permission is granted to display, copy, distribute and download the materials in this doc-ument for personal, non-commercial use only, provided you do not modify the materials and that you retain all copy-right and other proprietary notices contained in the materials unless otherwise stated. No material contained in this document may be "mirrored" on any server without written permission of NextHop. Any unauthorized use of any material contained in this document may violate copyright laws, trademark laws, the laws of privacy and publicity, and communications regulations and statutes. Permission terminates automatically if any of these terms or condi-tions are breached. Upon termination, any downloaded and printed materials must be immediately destroyed.
Trademark Notice
The trademarks, service marks, and logos (the "Trademarks") used and displayed in this document are registered and unregistered Trademarks of NextHop in the US and/or other countries. The names of actual companies and products mentioned herein may be Trademarks of their respective owners. Nothing in this document should be construed as granting, by implication, estoppel, or otherwise, any license or right to use any Trademark displayed in the document. The owners aggressively enforce their intellectual property rights to the fullest extent of the law. The Trademarks may not be used in any way, including in advertising or publicity pertaining to distribution of, or access to, materials in
this document, including use, without prior, written permission. Use of Trademarks as a "hot" link to any website is prohibited unless establishment of such a link is approved in advance in writing. Any questions concerning the use of these Trademarks should be referred to NextHop at U.S. +1 734 222 1600.
U.S. Government Restricted Rights
The material in document is provided with "RESTRICTED RIGHTS." Software and accompanying documentation are provided to the U.S. government ("Government") in a transaction subject to the Federal Acquisition Regulations with Restricted Rights. The Government's rights to use, modify, reproduce, release, perform, display or disclose are
restricted by paragraph (b)(3) of the Rights in Noncommercial Computer Software and Noncommercial Computer Soft-ware Documentation clause at DFAR 252.227-7014 (Jun 1995), and the other restrictions and terms in paragraph (g)(3)(i) of Rights in Data-General clause at FAR 52.227-14, Alternative III (Jun 87) and paragraph (c)(2) of the Commer-cial
Computer Software-Restricted Rights clause at FAR 52.227-19 (Jun 1987).
Use of the material in this document by the Government constitutes acknowledgment of NextHop's proprietary rights in them, or that of the original creator. The Contractor/Licensor is NextHop located at 1911 Landings Drive, Mountain View, California 94043. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in applicable laws and regulations.
Disclaimer Warranty Disclaimer Warranty Disclaimer Warranty Disclaimer Warranty
THE MATERIAL IN THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. TO THE FULLEST EXTENT POSSIBLE PURSUANT TO THE APPLICABLE LAW, NEXTHOP DISCLAIMS ALL WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON INFRINGEMENT OR OTHER VIOLATION OF RIGHTS. NEITHER NEXTHOP NOR ANY OTHER PROVIDER OR DEVELOPER OF MATERIAL CONTAINED IN THIS DOCUMENT WARRANTS OR MAKES ANY REPRESEN-TATIONS REGARDING THE USE, VALIDITY, ACCURACY, OR RELIABILITY OF, OR THE RESULTS OF THE USE OF, OR OTHERWISE RESPECTING, THE MATERIAL IN THIS DOCUMENT.
Limitation of Liability
215
UNDER NO CIRCUMSTANCES SHALL NEXTHOP BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOSS OF DATA OR PROFIT, ARISING OUT OF THE USE, OR THE INABILITY TO USE, THE MATERIAL IN THIS DOCUMENT, EVEN IF NEXTHOP OR A NEXTHOP AUTHORIZED REPRESENTATIVE HAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IF YOUR USE OF MATERIAL FROM THIS DOCUMENT RESULTS IN THE NEED FOR SERVICING, REPAIR OR CORRECTION OF EQUIPMENT OR DATA, YOU ASSUME ANY COSTS THEREOF. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT FULLY APPLY TO YOU.
Copyright © ComponentOne, LLC 1991-2002. All Rights Reserved.
BIND: ISC Bind (Copyright (c) 2004 by Internet Systems Consortium, Inc. ("ISC"))
Copyright 1997-2001, Theo de Raadt: the OpenBSD 2.9 Release
PCRE LICENCE
PCRE is a library of functions to support regular expressions whose syntax and semantics are as close as possible to those of the Perl 5 language. Release 5 of PCRE is distributed under the terms of the "BSD" licence, as specified below. The documentation for PCRE, supplied in the "doc" directory, is distributed under the same terms as the software itself.
Written by: Philip Hazel <[email protected]>
University of Cambridge Computing Service, Cambridge, England. Phone:
+44 1223 334714.
Copyright (c) 1997-2004 University of Cambridge All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
* Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
* Neither the name of the University of Cambridge nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Eventia Reporter includes software whose copyright is owned by, or licensed from, MySQL AB.
216
February 2007 217
Index
AAdd Class of Service
window 144, 151Add Interface window 136Add QoS Class Properties
window 144, 150Adding Comments to a Rule 140allocation of bandwidth 200Authenticated IP 113Authenticated QoS 153
definition 103using 153
Bbandwidth
allocating 45sample allocations 204
Bandwidth Policyfetching last installed on
host 183loading 183
CCheck Point QoS
architecture 39deploying 104displaying page 112distributed configuration 35Global Properties 112installing and configuring 39topology restrictions 202
Citrix 197Citrix ICA Application
Names 157Citrix MetaFrame Support 104Citrix Printing Rule 162
Class of Service Properties window 151
classifying trafficby service and source 79by source 79
Client/Serverinteraction 36
commandscpstart 181etmstart 180, 181etmstop 180, 181fgate 181fgd50 180
Comment window 141comments
adding to a rule 140concurrent sessions 38configuration
distributed 35Configuring a Citrix Printing
Rule 162Configuring Check Point QoS
Topology 163connections
classifying 44constant bit rate
computing 97ensuring it is not
exceeded 100in defining a class 96limits on 97
cpconfig 37
Ddefault rule 47, 77
for sub-rules 47default weight 113defaults
reset to 113rule weight 113units 113
Defining Sub-Rules 142
Denial of Service Attacks 199difference between guarantees
and weights 192Differentiated Services
(DiffServ) 144Differentiated Services, see
DiffServDiffServ
defining classes 145, 146definition of 93Expedited Forwarding
class 102interaction with other
rules 94IPSec packets 93versus Low Latency
Queuing 102Disabling Session Sharing 155
Eenforcing 51enforcing and installing,
difference between 51ERP applications 198example
Account Statics Logs 177Connection Reject Log 174Drop Policy Statistics
Data 178General Statistics Data 177LLQ Drop Log 174LLQ Statistics Data 178Pool Exceeded Log 175
Expedited Forwarding 102External Interfaces 192
Ffgate 183
fgate fetch 183
218
fgate load 183fgate stat 185fgate unload 183fgate ver 186
fgate ctl 187fgate debug 187fgate log 187fgate stat command 185first rule match principle 80FloodGate Module 35
logging 165status 164
FloodGate-1configuration 35GUI Management Client 35
FloodGate-1FloodGate requirements 19installation sequence 57technology overview 31
FloodGate-1 Topology 163
GGet Interfaces button 115GRE 197guarantees 80
definition 46interaction with limits 91per connection 46, 90total rule 46using 87
HH323 197
IIntelligent Queuing Engine 30,
31Interface Properties opening QoS
tab 114Interface Properties window 144,
150QoS tab 116, 144, 150
interfaces
activating 116Get Interfaces 115properties of 114
IPauthenticated 113non-authenticated 113queried 113
LLAN environments 200limits 80
definition 46interaction with
guarantees 91using 87
Load Sharing 106loading a Bandwidth Policy 183loaned bandwidth 193log
Connection Reject 171Drop Policy Statistics 173General Statistics 173LLQ Packet Drop 172LLQ Statistics 173Running Out of Packet
Buffers 171viewing 170
log collectionenabling 165
Log Viewer 167starting 167viewing 170
Low Latency classoverview 95priorities 96
Low Latency Classes 150Low Latency Queuing
class priorities 96classes 95constant bit rate 96defining classes 151implementation 150interaction with other rule
properties 100maximal delay 96overview 95versus DiffServ 102when to use 101
low traffic limit 200
Mmail server 198matching method
first rule 80maximal delay
computing 97in defining a class 96
maximum weight 113memory requirements 196Modifying your Security
Policy 156multiple modules 195
NNapster 199network objects 44
defining 56New Citrix TCP Service 160new rule
default weight 113next feature pack availability 198Non-authenticated IP 113
Pprioritize system administration
traffic 197Properties window 165
QQoS Class
adding 144, 150adding to Rule Base 144,
150definition 93DiffServ 93editing 144, 150Low Latency Queuing 95
QoS Classes window 145, 146, 151
QoS for Citrix ICA Applications 155
219
QoS for Citrix Printing 162QoS logging
turning on 165QoS Policy
installing 82installing and enforcing 51monitoring 52uninstalling 52verifying and viewing 51
QoS Rule tree 35Queried IP 113
Rrate units 113, 119RDED 31, 32resources
URI for QoS 45Retransmission Detection Early
Drop 32Rule Base
adding QoS Classes 144, 150
display 44, 123management 43
rulesadding and inserting 120adding to Rule Base 119adding under QoS
Classes 145, 151copying 122cutting 122default 47default weight 113deleting 122modifying 123naming 121pasting 122properties of 75source 124, 127, 128, 130,
134time 138track 135, 136
Sservices 45
defining 56
Services with Resource window 129
simple window definitions 134SIP 197SmartDashboard 35
starting 56SmartDashboard Rule Base Editor
window 44, 123SmartDashboard Rule Base
window 44, 123source
adding to a rule 124, 127, 128, 130, 134
classifying traffic by 79Stateful Inspection 30, 31status
of hosts, displaying using command-line interface 185
Status Manager 164Sub-rules 195sub-rules
bandwidth allocation for 49default rule 47defining 142example 81viewing 142
TTCP retransmitted packets 193TELNET
typical QoS Policy for 78Time in a Rule 138time objects 138top bandwidth hogging 196top bandwidth hogs 196track 135, 136Turn on QoS Logging 165
UURI for QoS resources 45Users Access
adding 125Users Access window 125utilities
fgate ctl 187fgate debug 187fgate kill 188fgate log 187
Vviewing
log 170Voice Over IP 198VPN-1 Power
interoperability 39sharing objects with 39
WWeight 112Weighted Fair Queuing 30, 31weights
calculating 45setting maximum 113
WFRED 30, 32windows
Add Class of Service 144, 151
Add Interface 136Add Object 124, 127, 128Add QoS Class
Properties 144, 150Class of Service
Properties 151Interface Properties 144,
150Properties 165QoS Action Properties 47QoS Classes 144, 145, 146,
151Services with Resource 129Users Access 125Workstation Properties 62,
114, 115Workstation Properties window
General page 64Topology page 66, 115
220